Search Documents

By P. A. Davies

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 11pp., 15 refs. Hazards such as vibration, dust emission and fragment projection can result in an area called the Danger Zone being set around a blasting site. Traditionally Danger Zones have been set solely on the basis of consequences (e.g. based on the maximum distance of rock projection or expected ground vibration plus a defined safety margin). Advances in risk assessment and its growing acceptance as a safety management tool have led to the setting of Danger Zones based on both consequences and frequency of occurrence. This allows distances to be optimised on the basis of acceptable risk levels rather than the potential consequences of infrequent events. The setting of a flyrock Danger Zone is used to demonstrate a risk-based approach compared with a traditional consequence approach

Aug 1, 1995

By C. C. Hustwit

The U.S. Bureau of Mines formulated a new mathematical model to characterize iron oxidation. The new model is intended to replace the currently used model, recommended by the Environmental Protection Agency (EPA), for most acid mine drainage (AMD) treatment applications. The new model was evaluated in a series of five synthetic AMD treatment tests. The initial ferrous iron concentrations ranged from 800 to 2,400 mg/L. In these tests, the Bureau model underpredicted the measured ferrous iron oxidation rates by a range of 3.24 to 8.03 pct. This was considered to be in close agreement after consideration of experimental error. The model proposed by the EPA was also evaluated using the same test data. The EPA model underpredicted the oxidation rates by a range of 77 to 100 pct in four tests and overpredicted by 19 pct in one test. The model formulated by the Bureau expresses that the rate of iron oxidation is a function of a treatment system's oxygen transfer efficiency and is independent of ferrous iron concentration when treated to near-neutral pH's. A new test method for evaluating oxygen transfer in flow-through reactors is also described.

Jan 1, 2010

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006

By Ananta L. Yennamani

Blast movement measurement (BMM) transmitters are a practical method to measure three-dimensional (3D) rock movement because of blasting. The BMM transmitters are activated, programmed and installed in specially designed drill holes prior to the blast and the BMM detector locates the transmitters after the blast. The BMM software then calculates and summarizes the 3D movement of each BMM transmitter ball. This information helps to redefine the ore and waste boundaries and enables improved ore and waste selection, resulting in a genuine step change in grade control. The BMM program was carried out at Newmont Mining Corp.?s Phoenix Mine, in northern Nevada near the town of Battle Mountain. The mine is in a historic mining district that contains gold, silver and copper. The geology of the pit consists of different formations made up of sandstone, siltstone, limestone, chert-pebble conglomerate, shale, skarn and quartzite, to name a few. Some of the rock is extremely hard and a powder factor of up to 0.5 kg/t (1 lb/st) is required to get adequate fragmentation to ensure sufficient throughput through the crusher and the mill. The result of using such a high powder factor translates into considerable blast movement and heave. This movement means that the ore/waste digging polygons estimated by the ore control engineer from sampling the initial blast holes will no longer be located in their original posi-tions. The purpose of this project was to test the measurement method and to see if locating the digging polygons in the broken muck pile and excavating to those polygons will improve grade control through the mill. Case studies (Zhang, 1994), (Taylor, 1995), (Gilbride, 1995), (Harris, 1997), (Taylor, 2003), Barrick Goldstrike (Gold-strike Mine, 2008), Ruby Hill Mine (Hilkewich, 2009), (Porcupine Mine, 2005) and (Aguirre, 2010) have shown that, by accounting for the blast movement, there is a potential to increase mineral recovery by as much as 25 percent for individual blasts for only a modest cost increase.

Jan 1, 2011

By Barbara Mazzini Loureiro

As placas de circuito impresso (PCI) são materiais heterogêneos e sua composição pode variar em função do ano de fabricação, tecnologia empregada, propósito de utilização, legislações vigentes e país de origem, entre outros. Essas características interferem diretamente no valor econômico agregado a estes resíduos, pois dependem da composição dos mesmos, de tal maneira que as empresas recicladoras tomam como base essas informações no momento da aquisição da sucata. Assim, a classificação e caracterização de PCIs é de suma importância para o mercado de reciclagem de resíduos eletroeletrônicos. A fim de alcançar este objetivo foi realizada cominuição em moinho de facas utilizando grelhas com abertura de 9, 6 e 3mm. A etapa de caracterização incluiu ensaios de digestão em água régia, perda ao fogo, análises química quantitativa por ICP-OES e MEV/EDS. Verificou-se que o lote de PCI estudado possui 39,5% de material cerâmico, 34,5% polimérico e 26 % metálico. A porcentagem em massa de cobre na placa é de 14,28%, de ferro 3,73%, de ouro 0,012% e de estanho 1,29%. O lote não é lead free e é multilayer com quatro camadas de cobre.

Aug 8, 2018

COUNCIL OF EDUCATION OF AIME (Formerly Mineral Industry Education Division) Established as a Division January 15, 1932 Established as a Council February 26, 1957 John C Calhoun, Jr, Chairman 0 Cutler Shepard, Vice-Chairman Thomas A Read, Secretary-Treasurer Dept of Mining & Metallurgical Engrg University of Illinois Urbana, Illinois COUNCIL OF ECONOMICS OF AIME (Formerly Mineral Economics Division) Established as a Division December 15, 1948 Established as a Council February 26, 1957 Louis C Raymond, Chairman Lorin A Cranson, Vice-Chairman Henry T Mudd, Vice-Chairman Adam K Stricker, Jr, Vice-Chairman Paul F Yopes, Secretary-Treasurer U S Bureau of Mines Albany, Oregon

Jan 1, 1957

By J Harris, M Shi, S Vink, P A. Kirsch

Across the life-of-mine, water is both an essential commodity to mining, and one of the most significant hazards. In Australia, a land of drought and floods, availability of water is a critical strategic risk for mine sites and neighbouring stakeholders, with both insufficient water leading to curtailed operations and contested space, and extreme water closing operations through flooding of mine sites, transportation infrastructure and unplanned regulatory restrictions. In addition to these major strategic risks, water must be addressed in operational risk management activities in many different ways.This paper develops a set of categories for classification of water risks based on academic papers from the water in mining literature. These categories are applied to media content analysis of articles in International Longwall News (ILN) (an online coal industry news site) obtained with the search terms ‘water’, ‘rain’ and ‘flood’. Identified risks are discussed within the context of the life-of-mine. The paper uses these same categories to analyse the treatment of water risks in a new coal industry risk management body of knowledge called RISKGATE (http://www.riskgate.org, Minerals Industry Safety and Health Centre, The University of Queensland). The discussion of water risks in both INL and RISKGATE is compared and contrasted to pinpoint opportunities (and a roadmap) for further development of a specific RISKGATE water module for site-based operations. The media review also identifies areas for development of RISKGATE expansion topic(s) that would address other strategic water risks, eg severe weather events.CITATION:Shi, M, Kirsch, P A, Vink, S and Harris, J, ?2014. Water as risk in mining – media analysis and the RISKGATE body of knowledge, in Proceedings Life-of-Mine 2014 , pp 205–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests.

Jan 1, 1934

By N. Kyriazi

The U.S. Bureau of Mines subjected the CSE SR-lOO self-contained self-rescuer (SCSR) approved by the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) to a series of laboratory treatments designed to simulate various environmental conditions in underground coal mines. The tests were designed to predict the ability of the self-rescuers to withstand those environmental stresses without causing a decrease in wearer protection. The apparatus were heated to 710 C for 48 h, cooled to -450 C for 16 h, vibrated for 9 h, and dropped 1 m on each axis. A critical concern was internal damage to an apparatus, without any obvious external signs, that would cause it to malfunction or seriously degrade its performance. Carbon dioxide (C02) levels in apparatus with combined treatments were higher than in apparatus with individual treatments and untreated apparatus. The higher levels remained within safe limits, however. None of the treatments caused venting of the small oxygen cylinder that provides starter oxygen. Some bottles were found to be empty because of manufacturing defects in the burst disks. This problem was corrected in later models. The heat treatments did make the case ends more difficult to remove and the breathing bag sticky and subsequently more difficult to unfold. An apparatus that was dropped and vibrated had a broken desiccant bag that released some of its contents which compromised the seal of the relief valve. The case was dented from the drops. As with the first-generation self-rescuers, if there is visible damage to the case of the apparatus, the apparatus should be considered to be internally damaged and must be removed from service.

Jan 1, 1990

By Mototsugu Matsuno

A new process has been developed to treat fly ash generated from municipal incinerators, which contains not only toxic metals such as lead and cadmium, but also dioxins. The process includes the following steps; fly ash is formed into green pellets with some additives and the pellets are then roasted to eliminate or stabilize the toxic metals and to decompose dioxins. A pilot plant with a capacity of approximately 100 kg/hr was used to test the process. The tests verified that heavy metals were either volatilized or stabilized and dioxins were decomposed by high-temperature roasting. The pelletized ash was found to be non-toxic, so that it can be recycled as artificial lightweight aggregate. It was also found that volatilized metals collected as secondary ash can be recycled as smelting resources.

Jan 1, 2003

By D G. Randall, R Jivanji, J Nathoo, T Reddy

Paradoxically, the increased emphasis on water treatment in mining has generated a new problem û hypersaline brines. Currently brines are either disposed of into ash systems, lined evaporation ponds or hazardous waste sites. Evaporative crystallisation (EC) is an alternative, but the energy requirements can be prohibitive and the salt product is still a waste that must be disposed of. Eutectic freeze crystallisation (EFC) is an alternative technology that is capable of separating aqueous solutions into pure water (as ice) and pure, solidified solutes. It is highly energy efficient and does not depend on the introduction of any solvents. In addition, the simultaneous production of pure ice and potentially saleable pure salt(s) is a major advantage. Although EFC has been shown to be effective in separating a single salt and water, it is still in the early stages of being applied to the multi-component hypersaline brines that are typical of reverse osmosis retentates generated by mining and extractive metallurgy.This paper presents an EFC brine treatment protocol developed by the Crystallisation and Precipitation Unit at the University of Cape Town. The protocol incorporates brine analysis, thermodynamic modelling to establish which salts will freeze out and at which temperatures, followed by experimental studies to determine the kinetic parameters, such as nucleation temperatures, salt yields and crystal purity.Case studies showing the application of EFC for the purification of typical brines containing high levels of sodium, chlorine, sulfate and ammonia (Brine 1) and a mixture of sodium and magnesium sulfate (Brine 2) are covered. Modelling tools were applied to describe the phase behaviour of the multi-component saline systems under different process conditions. Experimental validation was carried out using synthetic brines of different (and increasingly complex) compositions. The results showed that EFC could be used to selectively recover the sodium as a sodium sulfate salt from both different brines. The simulation tools were useful in the analysis and understanding of the process.A preliminary economic analysis showed that the operating costs for EC were approximately nine times those for EFC, but the capital costs were much less- equipment for EC cost about half that of EFC. However, it is important to note that the capital cost calculations for EC are based on a technology that is already well established and with only relatively marginal future equipment cost savings expected. In contrast, EFC is a new technology, with significant future technology improvements expected.

Jan 1, 2009

By Edward Rosenberg

The synthesis and characterization of silica polyamine composites modified with a variety of sulfur containing ligands is described. The two most successful ligands in terms of sulfur in-corporation and mercury capture are ethylene sulfide and carbon disulfide. The ethylene sulfide forms either an amino mercaptane or a polysulfide upon reaction with amino groups on the composite. The carbon disulfide undoubtedly forms a dithiocarbamate functional group upon reaction of the amino group under basic conditions. Both materials posses excellent capture kinetics and capacities for mercury, Once captured, the mercury is extremely difficult to remove from the composite materials, even with concentrated acids, and they easily pass the TCLP test. The materials are compared with related thioether modified silica polyamine composites and appropriate potential applications are discussed.

Jan 1, 2003

By R. H. Oitto

To determine whether reflectors could substitute for the trip lights referred to in the Federal Mine Safety Code, the Bureau of Mines studied trip safety devices under simulated haulageway conditions. The noticeability of reflectors compared with trip lights and fluorescent panels was evaluated from distances of up to 850 feet with light source intensities of up to 1-6 foot-candles (ft c). Reflectors tested consisted of a reflective lens in a holder secured to a frame that can be attached to a trip. Reflectors were found to be suitable for use as a trip safety device. In fact, for the conditions in many underground haulageways some reflectors would be more effective than a permissible trip light.

Jan 1, 1968

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

By S. A. Luciani

"In 1957, an asbestos orebody was discovered in the northern sector of the Ungava Peninsula of the Province of Quebec, an area now identified as Asbestos Hill. The deposit is situated on a plateau 1700 feet above sea level and 42 miles inland from Hudson Strait. It is a bleak, iso. lated location of typical arctic environment. Fifteen years were to pass before the first shipment of ungraded fibre was made in 1972. These years we1•e occupied with field surveys and investigations, diamond drilling, engineering design, evaluation of investment and operating costs, and construction. The problems normally associated with mine development were further complicated by location, isolation, and the extreme cold and permanently frozen ground of the arctic regions. Unique to an isolated arctic operation are the organization of support facilities and services, procurement and retention of personnel, construction of access roads and airports, and scheduling of product out and supplies in during the short summer period of sea navigation."

Jan 1, 1976

By Linney, Robert J.

REPUBLIC Steel Corporation's iron-ore properties in the Adirondacks consist of mines, mills, and sintering plants in the Mineville and Port Henry area and at Lyon Mountain. This article will deal with the properties in the vicinity of Mineville and Port Henry. In 1938, when Republic leased the Mineville- Port Henry operations from the Witherbee Sherman Corp., these properties had just come through some hard depression years. As a result, the mine development program was far behind schedule; most of the equipment needed replacement; and above all, the entire system of mining had to be completely changed to reduce operating costs. The concentrator had been in operation for many years; the process was dry and dusty. Machinery and equipment were either badly worn or entirely obsolete. The sintering plant, also long in operation, was badly in need of repairs.

Jan 1, 1943

By L. Maday, V. J. Perrone, M. B. Gilbert

INTRODUCTION The Brightwater conveyance system project in King County, Washington consists of constructing about 21 km (13 mile) of effluent and combined influent and effluent tunnels. The influent tunnels will collect sanitary sewerage from the service area and convey it to the new wastewater treatment plant (WTP) site at Route 9 in Woodinville, Snohomish County, Washington. The effluent tunnels will convey treated effluent from the WTP to an outfall at Puget Sound. The tunnels will be constructed primarily under residential areas, busy suburban roads and state highways. This 21 Km (13-mile) soft ground tunneling project faced many design challenges because of the geologic and hydrostatic conditions, long tunnel reaches, and large overburden depths. Boring depths typically varied from 45.7 M (150 ft) to 114 M(375 ft) with a maximum depth of 185.6 M (566 ft) deep. Conventional empirical methods for non-mountain terrain based on a 1:1 ratio of drilled footage per foot of tunnel bore (National Research Council, 1984) for evenly spaced borings provided a good start for the Phase 1 explorations. However a continuation of this approach with closer spacing was deemed inadequate by the geotechnical team for efficiently allocating geotechnical exploration resources for the final design. This paper presents a rational approach that was used to evaluate the value of a particular geotechnical exploration boring, pump test or other in-situ test. The method of analysis, which was initially developed for rock tunnels (Einstein et al., 1978), was modified for the Brightwater project. The method considers the potential construction cost risks resulting from variable geologic conditions, the cost and reliability of the geotechnical exploration and the earned value (cost risk reduction) of performing the geotechnical exploration. PROJECT DESCRIPTION In total the land portion of the conveyance system will include approximately21 Km (13 miles) of tunnels ranging in size from 3.0 to 5.2 M (10 to 17 ft) minimum inside diameter with overburden depths of 30.0 to 168 M (100 to 550 ft) and

Jan 1, 2005

With the launch of Immersive Technologies' next generation of Advanced Equipment Simulators for the mining industry, correlating and influencing safety, productivity and maintenance with operator competency improvements is now made even more effective. In early 2008, Immersive assembled a project team to investigate the potential linkages between operator competency and performance. Advanced Equipment Simulator Users with a range of sophistication were interviewed and consulted. The result was new and enhanced 'value realisation' programs to directly assist mine sites to deliver the expected return on investment (ROI) from simulators and operator competency development. In just over one year, 29 mine sites around the world have benefited from 34 completed programs. Case studies have been compiled to demonstrate the impact of the implementation of this approach, including at the following operations: Anglo Coal - Callide (Australia), Freeport McMoRAN - Grasburg (Indonesia), Equinox Minerals - Lumwana (Zambia), Peabody Energy - Cabllo (USA), and Xstrata - Lomas Bayas (Chile). Significant performance improvements have been achieved including: reductions of 47 per cent in gear shifting and 37 per cent in over speed errors, improvements of 68 per cent in park break errors and 12 per cent in spotting time, and increase of 54 per cent in passing emergency fire handling competency tests. This presentation draws on these case studies to clearly demonstrate the linkage between improved operator competency through the implementation of training programs tailored around Advanced Equipment Simulators and production performace measured by a range of standard metrics at mines around the world.

May 1, 2010

By Yoshinori Iwasaki, Shosei Serata, Yutaka Mochida

A new comprehensive insitu instrumentation technique named this RCC Method has been developed for rapid assessment and improvement of the structural stability of underground openings. When applied to tunnel construction, the degree of present and prospective safety of underground openings can be determined in quantitative terms within 10 to 20 minutes of microcreep observation. When applied to mining, roofs and floors can be stabilized by controlling the stress conditions. This stress control method has eliminated the need for intensive roof bolting and extensive floor renewal in all cases where it was applied. Use of this technique is illustrated by field examples from the Seikan Undersea Tunnel of Japan and deep potash mining in Canada. NEW INSTRUMENTATION TECHNIQUE: THE RCC METHOD Failure problems in underground excavation usually arise in weak non-elastic grounds where conventional rock mechanics theories of elasticity are not only useless but also misleading. Presently, discontinuity planes in the ground are being considered a factor in assessing these failure problems, and while this development is interesting academically, it is not of much use in actual excavation work, where it is nearly impossible to identify and quantize all existing planes of discontinuity. Even if such an extraordinary task could be accomplished at an underground excavation site, effective use of the data would be difficult and impractical for rapid excavation work, with the possible exception of rare cases of ideally elastic ground.

Jan 1, 1976

By R H. Sillitoe

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Geological concepts are employed routinely in porphyry copper exploration at the area selection, prospect appraisal and deposit definition stages. Regional, district-scale, deposit-scale and laboratory-based concepts can all play a role, with the resulting porphyry copper models providing templates for the integration of geochemical and geophysical responses and interpretations. Of the 19 concepts and parameters selected for brief discussion, those relating to subdivision of porphyry intrusions, understanding of diverse and commonly complex alteration-mineralisation patterns and lithocap characterisation are undoubtedly the most influential in exploration. Several of them are of particular importance because of their role in promoting grade development. Additional belt-, district- and deposit-scale features are currently little used but hold promise, whereas others have less practical value but help in underpinning the evolving porphyry copper genetic model.CITATION:Sillitoe, R H, 2015. Recent advances in porphyry copper geology and their exploration utility , in Proceedings PACRIM 2015 Congress, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015