Search Documents

By T Haskell, Y Joe, S Dickie

A current trend amongst producers is the increase in dewatering of iron ore fines (<0.5 mm), due to an increase in wet beneficiation processes used to upgrade lower quality ore deposits, increased water content in orebodies located below the water table, and increasing focus on transportable moisture limits (TML). Vacuum filtration is commonly used for dewatering of iron ore fines, and as with all filtration processes performance decreases with particle size. Significant improvements are possible with the use of filter aids, usually anionic surfactants and flocculants. Anionic surfactants reduce the surface tension of the associated water, which is then removed more readily leading to improved filtercake moistures. Anionic flocculants used correctly can improve cake permeability, in turn, decreasing cake formation times and increasing filtration rates. In addition to increased throughput, savings and benefits for producers can include: moisture limit penalties, improved handleability, along with energy and water savings.The effect of filter aids on two iron ore fines samples from the Pilbara region were evaluated using a lab scale vacuum filtration unit. The first sample showed a reduction in the filtercake moisture content by 2.3 per cent weight/weight (w/w) with the use of BASF’s Drimax® 1234. For the second sample a reduction in the filtercake moisture of 3.4 per cent w/w along with an increase in filtration rate of 20 per cent was achieved by using a combination of Magnafloc® 5250 and Drimax® 1239 NF, as both filter throughput and cake moisture were considered important by site.CITATION:Haskell, T, Dickie, S and Joe, Y, 2017. The use of filter aids on iron ore fines, in Proceedings Iron Ore 2017, pp 183–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Judicious placement of a range of geotechnical instruments was employed at the Tasmania gold mine, Beaconsfield, Tasmania, as a key strategy in the monitoring of rock mass conditions over the past four years. The range of instruments employed included vibrating wire stress-meters and hollow inclusion cells to monitor changing stress conditions, resistance wire and multipoint borehole extensometers to monitor the impact of stress changes on the integrity of the rock mass, and instrumented cable bolts and threadbar bolts to monitor the static and dynamic impact of rock mass changes on the installed ground control system. Initially the monitoring was of a qualitative nature, monitoring change from the time of installation. The value of the output was considerable when considered in relation to the ongoing seismic record which was also being monitored. It was clear from the seismic record and the monitoring results that stope blasting was the primary trigger for changing rock mass conditions. However, it was unclear how well observed behaviour was reflecting conditions anticipated by elastic numerical modelling. The latter had predicted significant stress increase in the near field of man-access footwall development. Qualitative monitoring and visual inspection did not support the modelling prediction, and this led to a program of quantitative measurement being undertaken. Measurement of the absolute stress condition in the backs of footwall development immediately adjacent to monitoring hollow inclusion cells provided the benchmark for tracking quantitative stress change. The program provided insight into the evolution of principal stress field magnitude and orientation in relation to rock mass change observed with extensometers and instrumented ground control elements, as well as providing a degree of calibration between the elastic numerical modelling and the virgin stress field. Calibrated monitoring data has also provided a useful benchmark for finite element modelling which is to be used for future mine-wide design.

Nov 25, 2010

By Timothy C. Siegel

Accurate representation of the geotechnical resistance distribution is critical in evaluating the performance of piles and pile groups for design. A current practice is to infer the geotechnical resistance distribution based on measured changes in strain during conventional top load pile testing. Especially for drilled and bored piles, the residual load is typically assumed to be negligible both during testing and after the application of the structure load. A practical result is that the compressive structural load is anticipated to be opposed primarily by the shaft resistance with little or no mobilized toe resistance. The predicted top deflection is estimated as the combined elastic compression plus the movement necessary to mobilize shaft resistance. The development of residual load (and associated negative skin friction) results in a significantly different design condition. Negative skin friction tends to force the pile into the ground and develops residual load in the pile that contributes to the internal compressive load. Significant toe resistance can be mobilized in order to resist the combination of negative skin friction and the sustained compressive load. The pile movement becomes a function of the toe penetration required to mobilize sufficient resistance to reach a balance of forces. In an effort to study the development of residual load in augered cast-in place (ACIP) piles, the authors installed and monitored strain gages that were embedded in an 18-inch diameter ACIP pile at a site in southeast Georgia. The results of this study indicate that residual load develops over time and reaches a distribution that is consistent with the principles of the unified design of piles. It is concluded that residual load develops in ACIP piles (as well as all drilled and bored piles by the same mechanisms) and that the residual load should be considered in the interpretation of load tests and in the pile design, particularly in the estimation of the single pile and pile group settlement.

Jan 1, 2009

By Patrick J. Foster

This paper summarises a behavioural safety project undertaken in seven quarries in the UK in order to investigate its applicability as a means of raising the standards of health and safety in the UK quarrying industry. A behavioural safety methodology was developed and trialled at two quarry sites in the UK. During the study the number of unsafe acts and minor accidents had decreased and at one of the quarries there was a 95% reduction in the number of working days lost. It was then introduced at a further five sites of varying sizes and within this focused specifically on lone workers as well as behaviours that affected quality and environmental issues. Positive improvements were noted in most of these operations. The project also looked at the effectiveness of health and safety performance indicators. Here, the common lead and trailing indicators for both safety and health that are commonly used by industry were identified. In consultation with the UK quarrying industry these were then used to identify specific performance measurement criteria that can be used by the quarrying sector to measure performance. Following on from this a quarry specific health and safety management system specification was developed for large and small quarries.

Jan 1, 2008

By Y. Bai, J. J. Liu, D. Q. Li, S. Z. Liu, X. T. Wang

"This paper presents the results of an industrial test using 8 t/d of Baotou concentrate (50% REO) of a clean metallurgical process, which includes: 1. Roasting with H2SO4 at low temperature (220~260 0C) in a batch roasting furnace followed by water leaching to obtain a leach liquor as feed with a yield of >95% RE and Th, recovering F as fluoride, producing a leach residue amounting to 1/3 of an equivalent high temperature residue and containing <0.03% Th and radioactivity < 3×104 Bq/kg compared to the normal high temperature residue containing 0.2-0.3% Th and 1×105 Bq/kg. 2. Separating Th with N1923 and extracting RE by P507 has been completed in mixer-settlers. Test results indicate that the ThO2 product has a purity of > 95% with a yield of 99%, and the RE has a yield of >95%, in which ThO2/REO <5×10-6, and that P507 loaded RE connect straight with separating RE using P507-HCl system. 3. Treatment and multipurpose use of "three wastes" (water, gas and solids) are discussed in some detail."

Jan 1, 2014

By P. N. Lategan

Mining companies are challenged with increased difficulty in delivering capital projects on schedule and within budget. In 2005, PricewaterhouseCoopers global review of major capital projects in the mining industry only 2.5% of projects could be defined as successful when assessed across the four critical dimensions of scope, cost, schedule and business benefits. Thus 97.5% of major mining capital projects were not successful according to the criteria PricewaterhouseCoopers used. Normally if a project fails on all these criteria it indicates scope creep. Scope creep refers to the change in a project&apos;s scope after the project work has started. As a result, the projects drift away from their original design, timeline, and budget, and as a consequence destroy business benefits. The major reasons for scope creep are poor change control and the lack of proper front end loading. Change control and front end loading are based on project processes in the planning and monitoring & control process group of the Project Management Body of Knowledge1 (PMBOK). This paper will focus on key factors to consider during project scheduling/planning with special reference to cost and schedule (using Microsoft Project as a tool although the principal is universal)

Jan 1, 2009

By Xiaohui Li, Lianyun Liu, Hongmin Zhu, Chunfang Zi, Kai Huang, Hongjie Li

"The dissolution kinetics of steelmaking slag in pure water was studied, and the relative influential factors were investigated. The dissolution behavior of slag particles in water was well described by Noyes–Whitney equation, and for this kind of sparingly soluble rigid mineral this simple model was extensively applicable to describe their dissolution process. Experimental data were also obtained to confirm the significant promotion effect on the growth of some algae.1 . IntroductionIt has been found that the population of phytoplankton distributed in the ocean was significantly related to the concentration of some elements [1]. For example, silicon and iron were very low in the high-nitrate low-chlorophyll (HNLC) areas, which was the main factor limiting phytoplankton and other biomass growth in these open ocean surface water [7]. The silicon and iron-rich test also confirmed that the supply of these elements had the direct effect on the growth of phytoplankton processes at HNLC areas [2-8]. So in order to promote the growth of phytoplankton in these ocean areas, providing some of these elements into these ocean areas is a natural idea for choice. Steelmaking slag is a good resource for consideration because it usually contains silicon, iron, phosphorus and other elements that are necessary for the growth of phytoplankton [8-10].Haraguchi has proposed the following idea that [5-6], if steelmaking slag can be spread to the open ocean, the trace components like silicate, iron and phosphate as the indispensable nutrients for the growth of phytoplankton, will be leached into the sea water, not only promoting the growth of phytoplankton, but also making good use of these huge amount of steelmaking slag produced every year. Based on this idea, they have carried out studies in recent years and they found that silicon and iron in the slag could be extracted into seawater effectively and play a positive role in the growth process of many algae. About the dissolution of the steelmaking slag, the Japanese scholars' research work mainly focused on the thermodynamic analysis of its dissolution possibility, and in the process of dissolution they tried to adjust the pH value of the seawater by continuously adding hydrochloric acid, which was deviated from the natural conditions of dissolution, and so the laws drawn under these special conditions can not give the identical guide to the practical application. Therefore, it is quite necessary to investigate the dissolution behavior of the steelmaking slag in the seawater at the normal pH range without adjustment to simulate the dissolution possibility under the natural conditions. In the present study, the silicon extraction behavior from the steelmaking slag was investigated and the dissolution kinetics in this process was also discussed in detail. Further studies were also performed here to evaluate the promotion of steelmaking slag on the growth of algae."

Jan 1, 2011

By Brajendra Mishra

Molten Salt electrolytic processes offer unique opportunities to extract and refine metals where gaseous or metallothemlic reduction, hydrometallurgical extraction and aqueous electrolytic methods are thermodynamically constrained. Production of aluminum and magnesium by molten salt electrolysis are well known commercial processes. Several other reactive metals, such as lanthanides and actinides, as well as beryllium and calcium, make use of molten salt processing for extraction and refining. This presentation describes the science of molten salt chemistry and electrochemistry for winning and refining of several metals. In addition, recovery of metals from waste process salts by molten salt reduction as well as oxidation have been discussed. Material issues in design of molten salt reactors have been included. Various applications have been presented through case studies. Experimental data have been included to justify the suitability as well as limitations of these specific processes.

Jan 1, 2003

By Y. Luo

Highwall mining, which is a relatively new mining method, is a preferred and often the only feasible method for extracting coal reserve left by surface mining operations in areas with steep terrain and in closely spaced thin coal seams. Though its safety record is comparable to that of surface mining, failures of mine structures in highwall mines, especially the highwall, have occurred. Methods for the systematic designing of highwall mines to meet the safety and operational challenges are still evolving. This paper presents the results of research into improving the existing design methods and developing new ones for highwall mining operations. The design methodology is aimed at ensuring structural stability of the highwall, roof, web and barrier pillars and preventing subsidence. It takes into consideration the major ground control challenges of soft and layered mine roofs, and interactions from mining closely spaced coal seams. An optimization design process applying a pressure arch concept can be incorporated to improve the recovery rate of coal reserve. A computer program based on the design methodology was developed.

Jan 1, 2015

By Junya Tokita

In Japan, packaged explosives have traditionally been used as the most common explosive for tunneling. Recently, some blasting systems such as ANFO with a kettle loader and emulsion explosives with a pump loader have been trialed in order to improve safety and efficiency of the charging process. There are issues with these systems relative to the Japanese market. ANFO dissolves in water easily, and generates ammonia gas when it contacts with concrete. Emulsion explosives need costly pump ing unit s, and there is a need to control residuals in the pump unit. Additionally, there are obstacles by Japanese law to site mixing of emulsion explosives.

Jan 1, 2005

By P. R. Segopolo

"The purpose of the project is to convert current shuttle car utilization on an underground coal mine to best practice by focusing on change-out points and tramming routes, which have a major influence on shuttle car away times. Time studies were an integral part of the project as these enabled the determination of shuttle car away times. An indirect proportional relationship between shuttle car away times and productivity is established. Through the time studies, it is deduced that a third shuttle car will make an insignificant contribution to production when there is only one split open. During this time, maintenance on the third car can be optimized. In order to satisfy the mine’s key performance indicator of keeping shuttle car away times less than 75 seconds, a belt extension must be scheduled after the third split is open. It is established that at any given time, a minimum of two shuttle cars should be used. When cutting on the left-hand-side of the belt road with only two shuttle cars available, the centre and left (left of the feeder breaker) shuttle cars should be used for coal hauling. When cutting on the right-hand-side, the centre and the right-hand-side cars should be used. If only one shuttle car is available, the centre car is the most efficient to use. Alternative anchoring configurations can be employed so as to enable cars (left or right, especially) to reach the opposite extremities of the panel and hence minimize cable length restrictions. Paper written on project work carried out in partial fulfilment of BSc. Eng. (MiningEngineering)"

Jan 1, 2015

By Mark Fennel

The present paper describes the operation and application of the QEMSCANTM automated applied mineralogy technology and how it is been utilized for long range planning by characterizing and optimizing the primary sulfide reserve while providing operational support of the ongoing secondary sulfide leaching operation at the Cerro Verde Mining Complex in Arequipa, Perú.

Sep 12, 2005

By Keith Heasley

This paper is a retrospective on the development, application, and enhancement of the LaModel program from a personal perspective. The narrative starts with an explanation of the objectives behind the original development of the program and then introduces some of the unique and very practical features of the program. Next, a demonstration of how LaModel was advantageously used to model stresses and displacements in a multiple-seam mining situation with highly variable topography is presented. This is followed by the details of a number of the major enhancements and expansions of the program over the years. A back-analysis of the Crandall Canyon Mine collapse is then briefly presented, along with the associated development of a recommended calibration procedure for the critical input parameters to LaModel. Finally, some of the present research areas are briefly described, and future enhancements are introduced.

Jan 1, 2011

The use of comparative sampling methods during the evaluation of the tin-copper deposits at Cleveland mine yielded closely checking average results from groove, channel, AXT split diamond drill core, and bulk sampling for both tin and copper content of the ore.The weighted mean tin and copper grades and values for the groove, channel, and split core samples showed small percentage differences from bulk sample results, and the F-ratio test for single population origin of the four types of samples was accepted at the 99&#183; 5 per cent level of confidence.These results indicate that grade estimates based on the assays from AXT split diamond drill core and/or groove samples would be reliable within practical limits.

Jan 1, 1968

The schlieren technique describes an optical analysis method designed to enhance light distortions caused by air movement. The ability to visualize air flow has significant implications for analyzing underground mine ventilation systems, including the enhancement of surveys and models. Currently, traditional schlieren methods are impractical underground. Background oriented schlieren (BOS) provides a solution to this problem. BOS requires two primary components, a professional quality digital camera and a schlieren background. A schlieren background is composed of a varying contrast repetitive pattern, such as black and white stripes. This background allows the camera?s sensor to capture minor light diffractions, such as those caused by air flow. Although BOS shows great potential for ventilation analysis, sensitivity is an issue. This paper seeks to validate the BOS technique for imaging flow through a regulator by comparing BOS images with traditional schlieren images. This paper also outlines initial experimental efforts used for the validation.

Jan 1, 2011

By John Kazakoff, Andrew Mortimore

"Production at the remote Kumtor Gold Mine in Kyrgyzstan commenced on schedule in December 1996.The ore mined during the first few months of 1997 from the upper benches of the pit did not produce the results predicted by the feasibility study. Low metallurgical recoveries experienced at the time were cause for great concern.It soon became clear the recovery difficulties centred around the preg robbing nature of the ore.Procedures were developed to selectively stockpile highly carbonaceous low recovery ore types. Testing methods were developed in the mill to quante the preg robbing activity of the ore. Preg robbing masking agents were added to the process to reduce the preg robbing activity of the ore.The importance of coconut carbon activity relative to the preg robbing activity of the ore was realized. Every aspect of the performance of coconut carbon in circuit was evaluated and optimized to improve carbon activity.Mineralogical analyses were completed defining the deportment of gold in ore and process tailingsBy year end the recovery difficulties had been overcome and plant design production had been achieved. Process improvements continue through 1998."

Jan 1, 1999

By E. Sun

Tailings disposal is a significant consideration for the mining industry, with the majority of the ore processed in most mining operations ending up as tailings. Several tailings dam failure accidents have occurred during the past few years and mine tailings dam failures are occurring at relatively high rates. Tailings dam failure is disastrous with the serious damage and the loss of lives. To increase the tailings dam safety, a tailings dam monitoring and pre-alarm system (TDMPAS) based on the internet of things and cloud computing platform has been accomplished with the abilities of real-time monitoring of the saturated line, impounded water level, rain fall and the dam deformations etc. The TDMPAS has been applied in several mines in China and helped the mine engineers monitor the tailings dam safety and get warning information automatically and remotely in any kind of weather conditions. This work has been demonstrated the tailings dam monitoring and pre-alarm system (TDMPAS) is meaningful to monitor the tailings dam physical safety condition. The TDMPAS could be applied to monitor all the national tailings dams online in the future.

Jan 1, 2012

By Verya Nasri, Mehdi Bakhshi

"Fiber reinforcement has emerged as an alternative to steel bars in precast concrete segments due to advantages such as saving cost and reducing production time while developing a more robust product with improved handling and long-term durability. ACI recently drafted a new report as the first design guideline on FRC tunnel segments to provide specific guidance for this emerging technology. ACI document offers general information on the history of FRC precast segments from tunneling projects throughout the world; a procedure for structural analysis and design based on governing load cases, and a description of the material parameters, tests and analyses required to complete the design. This paper summarizes the design considerations in this ACI guideline prepared by the authors of this paper as the main contributors. Application of this guideline to design of a tunnel with an internal diameter of 5.5 m (18 ft) results in elimination of steel bars.INTRODUCTIONPrecast concrete segments are installed to support the tunnel excavation behind the Tunnel Boring Machine (TBM) in soft ground and weak rock applications. The TBM advances by thrusting off the completed rings of precast concrete segments that provide both the initial and final ground support as part of a one-pass lining system. These segments are typically designed to resist the permanent loads from the ground and groundwater as well as the temporary loads from production, transportation and construction. Tunnel segments are generally reinforced to resist the tensile stresses at both the Serviceability (SLS) and the Ultimate Limit States (ULS). With traditional rebar, a significant amount of labor is needed to assemble the cages and place the rebar, which results in higher production costs.Fiber Reinforced Concrete (FRC) can be used to enhance the production, handling, and placement of precast concrete segments. This is because of the uniform dispersion of fibers throughout the segment to include the concrete cover, which is very advantageous for resisting the bursting and spalling stresses. These stresses develop as a result of the high loads induced on the segments during the TBM jacking process. The presence of fiber in the concrete matrix helps mitigate against unintentional impact loads during segment handling and tunnel construction operations."

Jan 1, 2016

By George S. Rice

In response to numerous requests for information as to the status of internal-combustion mine locomotives of the Diesel type that use heavy or non- volatile oil for fuel, with special reference to their safe use in coal mines, the United States Bureau of Mines is issuing this report. Data mere obtained, on application of such locomotives to cod mining only in Belgium, France, Germany, and Great Britain. The locomotives are used in coal mining in other countries, as well as in potash, iron, and other kinds of mining, but their chief development has been in coal mining in Germany, France, and Belgium. Recently popular interest in the Diesel type of engine for motive purposes was aroused in this country by the successful application of Diesel engines to railroad locomotives hauling fast transcontinental trains, and, according to published statements, at a low cost of fuel per mile of run.

Jan 1, 1936

By James J. Brady, Joginder S. Bhore, Robert B. Gordon, Jimmy W. Honeycutt

The authors of this paper have a combined construction experience of 70 years. They have served as engineers and managers on projects throughout the United States and Canada. Approximately 50 shafts have been sunk under their direct and daily participation. Several shafts have been selected from each of their experiences and have been briefly summarized here. SHALLOW SHAFT SINKING Sinking shallow shafts in highly urbanized areas adds an additional set of problems to those encountered in normal sinking operations. During the time between July, 1975 and early 1981, a series of shafts were sunk for The Washington Metropolitan Transit Authority. All of these were located along the "A" line, starting soon after the route departed from its path along Connecticut Avenue, proceeding to Wisconsin Avenue and then along Wisconsin Avenue to the city line at Western Avenue. (See WMATA System Map, Figure 1) The first three shafts were subcontracted from Morrison-Knudsen & Associates, Contract A9a, in July, 1975. They were: Albemarle Street - 27&apos;6" diameter, 78&apos;O" deep Brandywine Street - 30&apos;6" diameter, 88.6&apos; deep Ellicott Street - 33&apos;0" diameter, 110&apos;0" deep

Jan 1, 1985