Search Documents

By Moyle F. J

This paper describes an apparatus which was developed to study solid-vapour equilibria and presents results which were obtained during a study of the FeCI3-AlCI3-CI2 system. Analysis of the results showsthat fractional desublimation might offer a means of achieving a useful separation of the iron and aluminium chlorides produced by the chlorination of bauxite. The results, presented in the form of isothermal vapour pressure curves covering the range of temperature 160-200°C, support the earlier findings of Semenenko et al (Dokl Akad Nauk SSSR, 154: 42-43 (1964)) that the solid phase contains two terminal solid solutions.The equilibrium constant for the formation of the mixed dimer, FeAICI6, was approximately 4. The latent heat of sublimation of aluminium chloride varied from 18 to 26 kcal/mole AI2CI6 for solid compositionsfrom 0.9 to 0·5 mole fraction FeCls3.

Jan 1, 1979

By Silver EA

The Finisterre Range on the north coast of Papua New Guinea is the uplifted forearc riagio.n. of a modern arc-continent collision. The core of the range is composed of the P- nisterre Volcanics, an Oligocene''-arc terrane. The southern flank of the range consists of a clastic sedimentary sequence which is an uplifted accretionary wedge and collision complex. This clastic sequence can be subdivided into three distinct units. To the south of aiid structurally below the Finisterre Valcanics are the Mebu beds, an Oligocene- $arly Miocene sequence of volcanolithic turbidites. The Erap Structural Complex is south of, and structurally below the Mebu 43eds. , It consists of three subunits; the 3rly Pliocene micaceous turbidites of the Sukurum unit, contemporaneous pillow basalts AF{ the Basalt unit, and Late Pliocene to Pleistocene volcanolithic turbidites of the -Nariawang unit. The Quaternary Leron Formation, a fluvial to shallow marine 'clastic unit, is the southernmdst. and structurally lowest unit of the clastic -sequence The Finisterre Range is dominated by a fold-and-thrust belt with most thrusts "dipping steeply N. Melange fabric _ is developed in the vicinity of major thrusts. "ffle thrust belt strikes NW, oblique to the regional convergence direction, but no strike-slip motion is observed along NW striking faults.

Jan 1, 1991

Flue dust from the sintering of base metal sulphides was leached to remove cadmium and arsenic. Leach liquor contained cadmium, zinc and small amounts of other base metals as chlorides. Results are reported of the use of a cation exchange resin Zeocarb 225 to separate the base metals from the arsenic. The resin was eluted with sodium chloride or sulphate to give a solution of relatively concentrated cadmium suitable for recovery by zinc cementation. The limited solubility of sodium sulphate presented some practical problems which were investigated. Another problem was the precipitation of lead sulphate in the resin during elution.INTRODUCTIONWhen lead-zinc sulphides are sintered prior to smelting, the gases passing to the flue are mainly uncondensable but contain a certain proportion of sublimates and dust particles which deposit in the flue or are carried, after condensation in the gas stream, to some form of dust extraction equipment.The recovered dust is a complex mixture of base metal sulphates, sulphites, sulphides, chlorides and oxides, the composition depending on the original concentrates. A large proportion of the cadmium and some of the arsenic originally in the concentrates finds its way to this flue dust, the treatment of which can be a convenient means of removing these elements and controlling their concentrations in the main lead-zinc smelter circuit. However, disposing of this material represents an appreciable waste of base metals as well as a serious toxicity hazard.Sulphide Corporation Pty. Ltd. was faced with this problem in planning the flow sheet of the new lead-zinc smelter at Cockle Creek, N.S.W. From a test run carried out on a pilot plant at Avonmouth, U.K., using a mixture of lead and zinc concentrates, a sample of dust was obtained for...

Jan 1, 1960

By John R. Koehler

Available barrier pillar design methods do not adequately account for overburden caving characteristics, the timing and magnitude of associated load transfers, the occurrence of unusual geologic features, or the effects of multiple-panel/multiple-seam mining. To address this problem, the Bureau of Mines, in cooperation with Cyprus Plateau Mining Corporation, conducted a barrier pillar study in a multiple-seam mine setting. Insufficient barrier width resulted in excessive load transfer to an adjacent/underlying section. Consequent entry and pillar deterioration resulted in the section being prematurely abandoned. This paper proposes an approach based on in situ measurements, which includes mine-specific loading conditions in the barrier design process.

Jan 1, 1989

The dynamic response of holdup in a continuous ball mill has a direct influence on the rate function of grinding kinetics and is useful for predicting the variation in the size distribution of the finished product with time.A model was proposed involving three interacting, completely mixed chambers and this was used to derive analytically the transfer function of the system, from which the unit impulse response and the unit step response of the holdup with feed rate were obtained.The theory was confirmed by comparing it with previously published experimental data for the residence time distribution of particles passing through a ball mill.

Jan 1, 1975

By W. T. Benson

Peacetime production of mercury in the United States is controlled by world mercury prices, with significant lags to be expected between price increases or decreases and resultant increased or decreased production. Twenty-four mercury-bearing mines and prospects in widely separated districts in western and central Nevada and one property on the Nevada-Oregon border were examined and sampled. The purpose of the project was to determine if some of the properties warranted more extensive exploration work to obtain information on possible reserves of commercial-and sub-commercial-grade ores. The investigation of mercury deposits in Nevada was sufficiently widespread and indicated several areas of interest in the State that merit further exploration work.

Jan 1, 1956

By T. Lilley

The use of membranes in wastewater systems has increased rapidly in recent years. Microporous or semi-permeable barriers augment conventional chemical or biological processes to meet stringent treatment targets. These developments enable elegant solutions to wastewater discharge challenges and extend the scope of water recycle redressing the overall water balance and operational economics Wastewater treatment processes are discussed by reference to the spectrum of waterborne contaminants and the respective membrane separation capabilities. The role chemical pre-treatment to enable physical separation of metals with micro-filtration (MF) is described and how integration of MF with reverse osmosis (RO) is used to control a broader range of dissolved contaminants Membrane configurations are considered apropos function, operational economics and sustainability. These features are exemplified with case studies. Firstly, MF alone following chemical precipitation for the removal of heavy metals, then MF onto two stages RO of different configurations for TDS reduction and waste volume minimisation and finally an open channel RO alone for the reduction of inorganic COD from a leach stream.

Feb 27, 2013

By Kimiz Dalkir

Some things to keep in mind? ! What is your role in knowledge management? ! What knowledge-related challenges are you facing today? ! How does important knowledge get shared in your organization? ! Can you name factors that enable/block innovation and organizational learning in your work context? A brief history of KM? ! Top-down / imposed ! Rigid / bureaucratic ! Slow deployments ! Expensive ! Unpopular: empty libraries, info-junkyards, low adoption rates ! Problems measuring success ! The result: traditional KM is not the answer

May 1, 2003

By K. Viking

The vibratory characteristics of full-scale sheet piles, vibratory driven into the ground, have so far not been described systematically in detail. This paper concerns the preliminary results of a series of full-scale field tests where both the driveability and induced ground vibrations have been continuously monitored. Furthermore, the results of measured ground vibration levels have been measured at two different sites characterised as having hard and easy driving conditions. In the light of the presented results, the paper briefly discusses how the complexity of a driveability and vibration prediction can be subdivided into three parts, namely, vibrator-, sheet pile-, and soil-related parameters, all of which significantly affect both the driveability and induced ground vibrations.

Jan 1, 2000

By P McCarthy

"This paper is based on 30 years of involvement in feasibility studies as a participant, study manager and the leader of a firm that provides study components and overall study management. The following topics are discussed:the purpose of feasibility studiesaligning the goals of the study team with those of the ownerthe difference between optimisation and designhow the types and levels of studies affect the organisation of the studythe relative merits of various management structures and contractual arrangementssetting scopes of work and tendering the work outthe selection of a study manager and the study management teamcommunications within the study team and externallythe project management trianglemanaging scope changes and maintaining flexibility to respond to study findingsprogress paymentsmanaging a study crisisinnovation, risk aversion and bankabilityreporting the resultsthe dangers and benefits of value engineering.CITATION:McCarthy, P, 2016. Making studies work – organisation, communication and management, in Proceedings Project Evaluation 2016, pp 20–30 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

The extent of regional stratigraphic and structural geological mapping so far carried out in Australia is likely to be greatly overestimated by uncritical inspection of the latest authoritative geological map of the continent-that so ably compiled by the late Sir'T. W. Edgeworth David. Vast areas geologically coloured on this map are in fact known only from the most meagre field data, some of Which even include observations of distant views from which the so-called "geology" has been indicated in' reconnaissance reports.This applies to large areas in Cape York Peninsula; the plateau of Arnhem Land, and its margins except on the west where the Pine Creek mineral belt is better known; to the Desert Basin of Western Australia, practically the whole of the western half of the Northern Territory, much of east-central Western Australia, and northwestern New South Wales. Other vast areas are, more happily perhaps, left blank. It is true that prospecting parties have, at various times and with varying degrees of thoroughness, traversedparts of these little-known regions, often, however, in the search for gold or the.more obvious types of metalliferous mineral deposits and, furthermore, too often without leaving any written account of their examination, or with very sketchy details supplied. Unpublished geological surveys also cover some parts of these regions, but, on the whole, the picture we can draw of the regional deployment of rock masses in Australia is far less full than even David's map, with its obvious blanks, presents to us.Lest the practical mineral seeker among us should be inclined to place too much reliance on the prospecting to which I have referred.as giving him a straight hint of what country to keep out of, we may point to the recent discovery of a major sedimentary basin in the east KimberllilYs on which Dr. Teichert will have more to say. And that there are new metalliferous mineral deposits to be foundin parts of these little-known areas no one can doubt, for, after all, new discoveries are made from time to time in areas so well-known as the Victorian gold-fields. I take it then that regional geological mapping is a necessary concomitant of the further development of Australia's mineral resources-but I am not of the school that places it first on the list of priorities, and furthermore I believe that there can be a royal road to regional mapping-an inspired approach based on knowledge already gained and led to fruition by field surveys in key areas, by which there may be obtained a result giving a significantly close approach to actuality with only a fraction of the work that would be required for detailed field surveys on a systematic basis. I believe that a policy of rapid reconnaissance of such a type should be adhered to, especially in view of present deficiencies in numbers of geologists available for all purposes in Australia. The details that must eventually be sought can, I believe, be filled in later as the whole country becomes more developed and amenable to detailed surveys.

Jan 1, 1950

By Nicol S. K, Firth B. A

Much effort over the years has been put into the task of devising parameters which adequately assess the metallurgical efficiency of mineral processmg operations. One of the most celebrated of these methods is the so-called "release analysis" method of Dell (1953) which tackles the problem in terms of an ideal separation based on sequential retreatment of the products and tails of a given separation process. Other methods have also been proposed by Jowett (1969) and by Holland-Batt (1971 ). While these procedures are appropriate to multi-component mineralogical separations, they perhaps do not lend themselves to the much more simple two-component systems encountered in coal preparation. However Dell (1962) has suggested the use of the term "specific profit" in coal preparation in order to assess the conditions that give maximum economic gain. Specific profit is derived from data relating washability data with equipment performance and operating costs. The procedure for using this criterion for comparative purposes is therefore somewhat cumbersome as is illustrated by its lack of widespread acceptance in the coal preparation literature.In contrast, an efficiency index, E, which is both simple and meaningful from the utilitarian standpoint, has been proposed by Tsiperovich and Evtushenko (1959a). This index is defined by the relation, E = Yield X Tailings ash/Product ash (1) A cursory examination of this parameter shows that it increases when yield and tailings ash increase and also when product ash decreases; all of which are desirable circumstances in coal cleaning operations.Further, it will be shown that slight variations in operation are amplified by this function which makes comparisons simple and direct.While the use of this index is quite extensive in the Soviet coal preparation literature for some reason it has not received wide usag~ elsewhere.

Jan 1, 1978

By Terry P. Medhurst, Stuart A. MacGregor, Peter J. Hatherly

In addition to fractures and joints, compositional factors and bedding influence the strength of clastic sedimentary rocks. Rock mass rating schemes must therefore consider all of these factors. In this paper, a rating scheme for clastic sediments based on geophysical measurements is described. Geo-physical logging allows an approximation of rock com-position to be obtained and an assessment of bedding frequency and laminations. Velocity measurements incorporate the effects of fracturing. The rating requires scores for the intact rock, bedding/cohesion, and defects. These are combined to yield a Geophysical Strata Rating (GSR). Determination of the GSR is objective and repeatable. GSR values are typically between 20 and 80 and can be related to the Coal Mine Roof Rating.

Jan 5, 2007

This report is the 21st in a series summarizing research and technologic work on coal and related investigations by the Federal Bureau of Mines - the Chard of the series published on a calendar-year basis 2/ Subject publica¬tions of the Bureau during 1956 are cited, and pertinent Bureau work is described briefly. The most effective method of conserving our important coal reserves is through improved technology of production and utilization. Associated problems form the program of the Bureau.3 4 5 6/ Potential production is depend¬ent on a knowledge of the quantity and quality of the reserves, and the Bureau continues to contribute information on this subject. Many problems are being studied that relate to improvements in current production, including mining methods and health and safety measures. Preparation of mined coal is necessary for its most efficient utilization. Preparation by conventional methods is being studied, as well as the development or new methods. Fundamental studies on the structure and properties of coal are necessary to insure full advantage of the special qualities of different coals. Controlling factors in the efficient use of coal in combustion, carbonization, gasification, and direct and indirect hydrogenation of coal are being studied continuously, and new processes are being investigated. The many advances in all these fields are discussed.

Jan 1, 1959

By Xuehua Zhang, Shengxiong Yang, Huiqiang Yao, Gaowen He

"Seamount cobalt-rich ferromanganese crusts (hereafter crusts) are authigenic iron/manganese hydroxide/oxide deposits formed from direct precipitation of minerals from seawater onto a hard substrates surface. Crusts contain significant concentrations of cobalt, manganese, nickel, copper, platinum, rare earth elements and other valuable metallic elements, with potential economic value. Regulations on Prospecting and Exploration for Cobalt-rich Ferromanganese Crusts in the "Area" was approved by the Council and Assembly of the International Seabed Authority in July 2012, China and Japan became the first to obtain exploration contracts, which were signed respectively in April and January 2014.The crusts form pavements and are mainly attached tightly to the surface of the substrate, and less commonly crusts coat talus debris located on the surface of sediment and substrate rock. During prospecting, crust sampling methods mainly include dredge, TVgrab and sub-bottom coring system. During exploration, the sub-bottom coring will be the dominant method for crust sampling, and if necessary, ROV sampling will be used. Usually the samples collected by different methods provide a larger quantity than samples needed for chemical analysis, but sampling quantity is a question that should be considered for mineral resource evaluation that how to ensure that the sampling is representation for the sampling station. Using the samples collected by China from Pacific seamounts, according to the designed analysis flow and Qeqott formula (Q=Kd2), the minimum reliable assay sample quantity ("MRASQ") of crusts for Mn, Co, and Ni are obtained. In the case of the sample homogeneous fines at ~100 mesh size (~0.15 mm), MRASQ for Mn, Co, Ni is respectively 4.5 g, 9 g and 9 g. This result provides the basic data for crusts resources evaluation."

Sep 1, 2014

By P. M. Wiltcher

The construction of a deep structural slurry wall in a restricted city centre location is always a challenging prospect. However, when the city is London and the site is bounded on two sides by high level canals and a main traffic highway on the third, the challenges are greater than usual. The paper discusses the design considerations required by the principal contractor to accommodate a single high level lateral support, value-engineered, bottom-up construction technique and the impact this had on the design detailing and construction of the slurry wall panels. This paper discusses the logistical challenges successfully overcome during the construction of 65,000sq ft of 40inch thick, 80ft deep structural slurry wall in the City of London. The paper reviews the benefits gained from using the state-of-the-art hydraulic grab and rotator system. Technological advances in computer instrumentation and real time monitoring were utilised to assist the grab operators in consistently delivering deviational control during excavation better than 1:200. With working space always at a premium on construction sites, the need for high quality, pre-fabricated reinforcement cages has never been greater. This paper reviews the argument for off-site fabrication of reinforcement members.

Jan 1, 2006

By J. P. BONARDI, C. W. Davis, R. B. Moore, J. W. MARDEN, S. C. Lind, J. E. Conley

The rare metals are becoming increasingly important to our industries. Rare-metal alloys have properties which indicate that we are only on the threshold of the possibilities of their utilization, not only in making nonferrous alloys, but also as special steels. Not only are their uses broadening rapidly, but the metals are affecting our industries in other ways. The oxides and some salts are used as pigments; others have medicinal value. The pure metals are made into filaments for incandescent lamps, and targets for X-ray tubes. By their efficient use in alloys, the weight of automobiles is reduced, • and the wear and tear on tires and roads is thus minimized; in machine shops they help to give greater efficiency to tools and reduce production costs. Their development has marked a milestone in the progress of civilization. There has been considerable uncertainty regarding analytical methods for the rare metals. A great deal has been published, but the weak and the strong points of the various methods have not been investigated as carefully as is needed. The Bureau of Mines at its Rare Metals station in Colorado necessarily had to do a great deal of analytical work in connection with the metals covered by this bulletin, which aims to give the results of the experience so acquired. No claim for much originality is made, although some published methods given have been modified, and some new ones have been developed by members of the staff. The principal methods available were studied critically, and it is to be hoped that the work will assist those interested in analytical work in connection with the metals named.

Jan 1, 1923

By S. Agarwal, S. Frimpong

The creation and maintenance of a healthy working environment in surface mining operations require sustained efforts in pursuing advanced research initiatives toward the development and deployment of powered haulage technologies. This paper contains progress summary on a frontier research in truck dynamic control, vision and collision avoidance. This research is required to provide solutions to challenging problems regarding operator visibility in truck haulage in a surface mining environment. The paper focuses on truck control kinematics and dynamics, truck-haul road interactions, intelligent truck sensing, intelligent truck collision avoidance system, integrated system for situational awareness, augmented visualization and operator interface, and field testing and error variance modeling of developed technologies. A sensor suite of four subsystems, including front-side stereo-camera, front-side Doppler radar, close range sonar proximity sensors, and rear-side camera system have been recommended for developing a 360° truck operator vision to allow safe operations. This research initiative is significant because it will provide a strong basis for developing technologies to improve truck haulage safety in surface mines and construction sites.

Jan 1, 2007

By R. Elliott, C. A. Pickles, J. Peacey

As the nickel sulfide ore deposits become decreasingly viable as a source of nickel metal, increasing attention is being paid to the exploitation of the nickeliferous laterite ores. Attempts to produce a high grade ferronickel concentrate from these ores by pyrometallurgical methods face several challenges, in particular the selective recovery of the highly disseminated nickel from the reduced ore. The current work explores strategies for maximizing the size of ferronickel particles formed in order to improve the selective recovery of the ferronickel by magnetic separation. The effect of various coal, elemental sulphur, pyrite and sodium sulphate additions on ferronickel particle formation and size at 1000°C have been investigated. It has been observed that increased coal additions leads to a moderate improvement in the size of the ferronickel particles, while the presence of any sulphur bearing reagent leads to a significant increase in particle size. The retention of sulphur in the reduced material has also been studied, showing sodium sulphate has the highest retention, followed by pyrite and then elemental sulphur. An inverse trend was observed in the efficiency of sulphur retention on the basis of residual mass of sulphur per unit mass of reagent added.

Jan 1, 2015

By Robert A. Field

Static-Load Piledriving utilizes a hydraulic push to facilitate the installation of a pile. The pile is not rotated, impacted or vibrated. A smooth pushing force advances the pile incrementally into the ground. Static-Load devices must have a reaction mass to push against. The most simple form of a Static-Load device is a jack; more advanced equipment, such as the Still Worker, also utilizes this approach. This paper focuses on the use of the Still Worker on three challenging projects. In each case, the existing site conditions made it risky, or unattractive, to utilize conventional impact, vibratory, or drilled-shaft equipment.

Jan 1, 1997