Search Documents

By K. L. Murphy, G. Multamaki, P. M. Huck

"A preliminary evaluation, based on existing data, has been made of the implications of placing radium-barium sludge in tailings areas. The study was restricted to a consideration of possible increases in the quantities of radionuclides escaping to the environment through either groundwater or surf ace water, considering the types of tailings treated and the effluent treatment systems currently operating in Canada.IntroductionIn the recovery of uranium from ore deposits, the tailings produced by mine/mill complexes are conveyed to impoundment areas in slurry form. After settling, the supernatant is discharged to the environment together with runoff from precipitation on the tailings bas in. Currently, all operating uranium mines in Canada employ barium chloride treatment to control the release of dissolved radium to the aquatic environment. The dissolved radium in the tailings decant is precipitated with barium chloride, forming (Ra,Ba)SO4, and allowed to settle in ponds or lakes. In some instances, settling tanks have replaced ponds and flocculants have been added to aid settling. Because the Atomic Energy Control Board does not consider the precipitation ponds to be suitable for final disposal of these sludges, acceptable sites must be found. Options which have been suggested for sludge management include underground placement either in worked-out mine areas or in special chambers, or placement in the tailings areas. Conceptually, the latter alternative is attractive and probably would minimize sludge handling. This alternative would be subject to the AECB policy which requires that upon abandonment, radioactive releases from a tailings area must be within present regulatory limits and that treatment to meet these limits should not be required in perpetuity.No quantitative data exist concerning either the effect of physical and chemical conditions in the tailings on resolubilization of radium from precipitated sludges or the fraction of this additional radium which would be released."

Jan 1, 1982

By Daniel Su

Approximately 90% of the primary roof bolts used in CONSOL?s Pittsburgh seam coal mines is 2-piece, 8-foot long, 7/8? (or ¾?), high-strength, resin assisted, mechanical shell tensioned bolt. The remaining 10% is the 2-piece, 8-foot long, 7/8? combination bolt, which employs 4 feet of fast resin to anchor the deformed rebar at the top of the hole. In either system, a 1-3/8? hole is required to accommodate the mechanical shell and the coupler. The cheaper torque-tension rebar system, which is typically fully-grouted with 2-speed resin and which typically provides low bolt tension, is not used in CONSOL?s Pittsburgh seam mines. Rather, it is used in CONSOL?s Central Appalachia mines, where the roof rocks have CMRR rating of 50 or higher. Fully-grouted headed rebars, on the other hand, are used in CONSOL?s room-and-pillar mines. The selection of tensioned versus non-tensioned, fully-grouted bolts for coal mine primary roof support has been debated for the past thirty years. Many researches have been conducted to understand the theoretical bases behind the two systems. This paper describes CONSOL?s experience of using a new fully-grouted, mechanical shell tensioned bolt in the Pittsburgh seam with the development of low insertion force resin.

Jan 1, 2007

By J. Hansen

This paper has been written for presentation during the Open Pit Mining Session at the SME Annual Meeting and Exhibit, Denver, Colorado, February 26 to 28, 2001. The paper addresses the application of automated monitoring of electric rope shovels to improve performance and blasting technique.

Jan 1, 2001

By N. Charue

An international prediction event was carried out within the framework of a 30-pile testing program organized in a sandy soil in Belgium (Limelette). That program called upon sev­eral testing methods: static load tests, Statnamic testing, and dynamic testing. This paper provides a summary of received predictions and results obtained from the static pile load tests, which were carried up to failure of the instrumented piles. The comparison between predictions is made using load-settlement curves with reference to the results of the static load tests. The predictions are based on a geotechnical approach using an extensive soil investigation program and a dynamic approach using the dynamic load test data.

Jan 1, 2002

Sulphuric acid leaching at atmospheric pressure of a number of Australian nickeliferous laterites was examined in detail. The results obtained indicate that nickel can be extracted from these ores, although the conditions required to achieve about 90 per cent extraction vary widely. These differences in reactivity can be related to the types of nickel-bearing minerals present.Nickel is more readily extracted from nickel-bearing clays such as chlorite, than it is from nickel-containing goethite.The results clearly show the problems associated with the processing of complex ores such as the nickeliferous laterites, and they indicate the need for complete characterization of each deposit.

Jan 1, 1978

By M. Carrales

This Bureau of Mines report presents information on the sulfur content of crude oil in the United States and in some foreign countries. Data are presented for oil produced in 1971 from fields in 26 States that accounted for about 76 percent of total U.S. oil production; the foreign data cover fields in 24 foreign countries that accounted for about 64 percent of the total oil produced from these countries in 1971. Most of the data are presented in tabular form.

Jan 1, 1975

THE Wonthaggi coal-field lies south easterly from Melbourne at a distance by rail of 86 miles, on the flats of the Powlett River, immediately to the south of the deep-cut valleys and steep intervening ridges in the Jurassic rocks of the Bass Range and itsfoot-hills. The coal-bearing area is covered with a thin layer of late Tertiary and Recent deposits, which serve to mask the true character of the underlying coal-bearing rocks and effectually prevent the appearance of any coal outcrop. Two or three bores sunk prior to 1890 had shown the locality to be really a potential coal-bearing one. Only one additional bore was sunk in the State Coal Mine area until 1908, when energetic boring was resumed, with the result that in November, 1909, when an acute shortage of black coal in Victoria resulted from the prolonged strike on the New South Wales coal-fields, coal-seams had been located at Wonthaggi offering sufficient inducement to start an...

Jan 1, 1918

By Y Zhuang, S La Brooy

The selection of the optimum process route for a new project has traditionally consisted of investigating existing options and ranking them in terms of cost, technical risk and environmental acceptability. With the current focus on sustainable development other factors now need to be considered. Life Cycle Assessment (LCA) of the process options can be used to extend the assessment in terms of their potential for earning renewable energy credits and in judging their ability to achieve greenhouse gas emission reductions. A rigorous life cycle assessment is demanding in terms of setting the baseline for comparisons and evaluating the elements that make up the emission profiles of the process options. However, a simplified LCA can provide a useful tool for comparing different process options. This approach can be combined with traditional assessment criteria to rank the options available to the project. GRD Minproc has been intimately involved in executing LCA calculations for different municipal waste treatment options. This paper applies a similar LCA methodology to investigate the greenhouse gas implications for different options for copper processing. The process options considered are:concentrator û sale of concentrate to smelter, concentrator û on-site mini smelter, and concentrator û leach SX/EW. The paper then goes on to consider the operating cost implications that could arise with the introduction of carbon taxes or carbon credits and how these might impact on the future choice of flowsheet.

Jan 1, 2002

By Varadarajan Seshadri

Geometallurgical characterization of iron ore which is a raw material for Iron making as in the case of charcoal blast furnaces operating in Brazil or for production of agglomerates such as iron ore sinter which serves as burden material for blast furnces of high productivity or pellets extensively used in the direct reduction processes all over the world in the iron and steel industry. Selection of proper raw material after due characterization should lead to an improvement of the productivity of the respective processes The usual classification of quality of iron ore is uniquely based on chemical analysis, granulometric and physical parameters. However not much emphasis has been given to the structural characteristics which also are important in the processes. Different typological categories of Brazilian iron ores have been used in the characterization . For instance, several kinds of hematite crystals like specularite, martite and microgranular hematite, etc with variable crystal sizes are found in the different ore types. They are also composed of different of fabrics and types of accessorial mineralogical constituents and have different porosities, pore diameters, etc which influence the cold and the hot agglomeration stages of the ore fines, and also chracteristics such as reducibility, decrepitation etc, important for assessment of quality of iron ores. . The first step for attaining a good characterization of ores is to know in detail about the structure of the deposit, shape of the body, types of iron ores and their distribution. This requires a geological-structural study and the mapping of the bodies using mineralogical criteria for typological classification of ores. followed by structural characterization of materials in stages of mining, comminution, screening and concentration processes. In this contribution a geometallurgical approach for quality control of Brazilian iron ores for sintering and pelletizing processes is highligted.

Jan 1, 2006

By H. T. Chiwaye

Risk analysis is an important step in the design of rock slopes in open pit mining. Risk is defined as the product of the probability of slope failure and the consequences of the failure, and is generally evaluated in terms of safety and economic risk. Most of the risk analysis done at present is based on the use of limit equilibrium (LE) techniques in evaluating the probability of failure (POF) of the slopes. The approach typically makes use of full Monte Carlo simulations of the limit equilibrium models, with all uncertain variables randomly varied. The number of required simulations is generally over a thousand, at times as high as 20 000, in order to produce statistically valid results of the POF. Such an approach is clearly not practical when using numerical modelling programs dueto the high computational effort required. This paper explores the impact of using numerical modelling instead of the traditional LE techniques in evaluating the probability of slope failure. The difference in the overall assessed risk, in terms of economic impact, for the mining operation is then evaluated. With numerical models, approximate methods are used in the calculation of the probability of failure instead of full Monte Carlo simulations. This paper will use a method called the response surface methodology (RSM) for estimating the POF from numerical analyses. Simple slope models were used to verify the accuracy of the RSM method by comparing the results with those obtained from full Monte Carlo simulations. It is shown that there is good agreement between the POF values computed using full Monte Carlo simulation and those obtained using the RSM method. Finally, the use of numerical modelling in the assessment of risk is shown to bring a significant difference in the result compared with that from LE methods. One of the reasons for the difference is that LE models tend to underestimate the failure volumes and hence the consequences of slope failure.

Jan 1, 2010

By Y. K. Wong

This paper describes in detail various problems concerning the construction of a pile-raft foundation supporting a 42-storey tower block. The subsurface generally consists of highly weathered sedimentary rock. A comprehensive instrumentation program is implemented to monitor the behaviour of the foundation system throughout the construction period of the superstructure. Instrumentation observations are highlighted in the second half of the paper.

Jan 1, 2010

By Frederick M. Fowkes

Dusts can be filtered out of air streams onto polymer surfaces by electrostatic trapping resulting from the spontaneous transfer of electrons upon contact between dust particles and the polymer surfaces. Such spontaneous contact electrification has been studied quantitatively in this contract with the aid of modern semiconductor charge-sensors with the aim of determining what basic principles govern the sign and magnitude of contact electrification. Information obtained by capacitance-voltage measurements of thin polymer films on silicon showed that charges as large as 4 x 1012 electrons per cm2 develop spontaneously, and that such a charge gives adhesional forces of 165 pounds per square inch (11 atmospheres). Direct measurement of dust polymer contact electrification, using silicon surface channel conductance sensors, also showed spontaneous charges of more than 1012 electrons per cm2. Some polymers can either donate or accept electrons. These included chlorinated polyethylene, chlorinated polypropylene, polyethylmethacrylate, and a copolymer of maleic anhydride with n-octadecylvinylether. Other polymers never accepted electrons but could donate electrons; these included polystyrene, pulychlorostyrune, polyvinylchloride, polyvinylacetate, a polycarbonate (Lexan), and cellulose tributyrate. Contact electrification studies were made with dusts (coal dust, a channel black, or a silica powder) contacting thin films of various polymers solvent-cast onto the semiconductor charge-sensor. Sometimes charging was instantaneous and sometimes slower, but in all but one case (coal dust on a copolymer of maleic anhydride with n-octadecylvinyl ether) the charge trunsfer was a donation of electrons by the polymer to the dust. Some

Jan 1, 1973

Permian coal seams from the Tomago Coal Measures in the Northern Coalfield, New South Wales, were analysed petrographically and reflectance measurements made for each. Vitrite contents were moderate to high for most of the coals but for two they were very low.The mineral-matter contents were low to moderate by Australian standards. Different profiles of a particular seam could be correlated by petrographic methods.Standard seam profiles were drawn up and from these an idealized Tomago seam sequence was compiled. All the coals were of high-volatile bituminous rank. Their carbon contents, but not thcir reflectances, varied significantly with the quantity of vitrinite present.

Jan 1, 1968

By James Diekmann

The Disputes Potential Index (DPI) is a computer program designed to help team mem¬bers assess the likelihood of contract disputes on a construction project. The program's predictions are based on data from 159 construction projects that encompass a variety of public and private projects. The impact of three categories of project characteristics are included in the DPI program, specifically, people, process and project characteristics. Ultimately, DPI returns an overall project score that indicates the likelihood of exces¬sive contract disputes. The output of a DPI analysis can be used as part of a contract readiness review or to define the need for extraordinary dispute avoidance procedures. This paper examines the development of DPI and presents the results of DPI analyses on several tunneling projects.

Jan 1, 1995

By V N. Rudashevsky, F Melcher, J Lodziak, D Klosa, N S. Rudashevsky, M Sitnikova, L Gast

A combination of novel and æclassicÆ methods, namely electric pulse disaggregation (EPD), hydroseparation (HS), preparation of monolayer polished sections, and mineral liberation analysis (MLA) was employed to study ores from platinum pipes (Bushveld Complex, South Africa), pristine PGE mineralisation of the Main Sulfide Zone (Great Dyke, Zimbabwe), as well as ancient and modern gold/PGM placer deposits. It is shown here that the EPD technique liberates mineral grains of interest without any visible destruction allowing the study and analysis of individual rock-forming and ore minerals, in our case especially platinum-group minerals. The HS method is an effective tool in concentrating heavy minerals by factors up to 10 000 fold. As near-total recovery of grains >10 ¦m is achieved, the nugget effect can be overcome also in case of limited availability of samples (drill core, museum specimens). The MLA technique is a fast tool to detect and characterise mineral phases in ores and ore processing products. Many mineralogical parameters of individual grains and mineral assemblages can be deducted and documented. The results show that the techniques employed, either on their own or in combination, provide a wide range of additional information especially on platinum ores which is beneficial to both the researcher and the metallurgist.

Jan 1, 2008

By Chu E. Ho

Field load tests on deep slurry stabilized bored piles have shown that end bearing resistance was unreliable due to soft toe conditions caused by debris accumulation at the bottom of the hole during pile installation. This is true whether bentonite or polymer slurry was used. Skin friction resistance was less affected by the slurry and is more reliable. A design strategy is proposed which ensures that an adequate factor of safety against the ultimate shaft resistance is maintained for any chosen design working load, such that a pile settlement of 12mm would not be exceeded.

Jan 1, 2002

By D. Brün, T. W. Nattkemper, T. Kuhn, T. Schoening

Underwater exploration for marine resources using camera-equipped devices (OFOS, ROV, AUV) is receiving growing attention. This development is creating a continuously growing pile of digital underwater images leading to a serious bottleneck in the analysis. However, any harvesting strategy must be coupled to an efficient and effective assessment of the biodiversity in the area of interest and in nearby control areas. To integrate manual image and computational image interpretation on different levels (i.e. regarding geology and environmental sciences and taxonomy), sophisticated software support is required, which is not yet offered explicitly, neither by commercial software companies nor by academic or other publicly founded institutions. Here, we present the first version of a new digital asset management system that offers functionalities for easy data management, sharing, manual annotation and integration of computational modules for image enhancement/pre-processing and interpretation. The functionality is demonstrated with data from the CCZ provided by the BGR Hannover.

Sep 1, 2014

Fire suppression systems are now recognised by both NFPA 502 and PIARC as legitimate tools for both life protection and asset protection. The effectiveness of these tools for life protection demands extremely rapid and accurate incident detection coupled with rapid response. This rapid response must be integrated with other emergency systems such as emergency ventilation. The March 2007 fatal Burnley Tunnel incident in Australia graphically illustrates the potential of effectively integrated fixed suppression systems to protect people from harm and save infrastructure from damage. Despite the raft of technology available in that instance to the operator it was the human operatorÆs ability to effectively control the emergency equipment and not the equipment itself which so positively influenced the threat to life and property.

Jan 1, 2008

Modelling and simulation are important aspects of flotation research, which may assist in the design of new circuits and the optimisation of existing ones. Flotation research in the AMIRA P9 project has developed a methodology for flotation plant modelling based on determination of cell (pulp) characteristics. froth characteristics, and ore floatability (using floatability components). The implementation of this methodology requires the determination of ore floatability, to which end a small flotation pilot plant known as the Floatability Characterisation Test Rig (FCTR) has been designed and then built and kindly made available to the AMIRA P9 project by Baker Process. The FCTR has a 2 tph capacity and consists of six 130 litre rougher/scavenger cells and six 50 litre cleaner/recleaner cells. The Mintek FloatStar pulp level control system is used to control the pulp level in all cells. A number of experimental procedures have been developed for using the FCTR to obtain the data required for the P9 flotation models. These procedures include how to determine the floatability parameters, Pi and mi, the bubble surface area flux, Sb, the mean residence of the pulp in the cell, t, water recovery. Rw, froth zone recovery, Rf, and the degree of entrainment, ENT. The flexibility of the FCTR allows it to be used in numerous flotation studies such as stream characterisation, reagent testing, grinding experiments, power studies, oxidation studies, and scale-up and simulation studies. This paper will describe the design and operation of the FCTR and the procedures that will be used to obtain data from the rig for modelling purposes.

Jan 1, 2000

By Alain Dorval

"''Purification of marine sands from Les Iles-de-la-Madeleine''This paper presents the results of the work that has been done at CRM pilot plant for «Les Silices du Golfe Inc.». Essentially the purpose of this piloting was to demonstrate, on a semi-industrial scale, the process of purification of marine sands from Les Iles-de-la-Madeleine; that had been developed by CRM Process Development Service. This purification is necessary to produce silica suitable for the glass sand and the foundry sand markets.Introduction«Les Silices du Golfe Inc.» is a company who intends to dredge marine sands around the «Les Iles-de-la-Madeleine» coasts. The material will be transported to Gaspesia where electricity, water supply, and a convenient site is available to treat it. A high purity silica intended for glass sand and foundry sand markets will be produced. The objectives of this purification process are to remove organics, calcium, feldspars and iron.Material ReceivedCRM received 50 tons of sand with Si02 varying between 80,6 and 99,3 % (see Figure.1). The highest variations in impurities were the calcium and lost on ignition. We notice direct relation between% SiO2, % CaO and % L.O.I. as you can see on the following Figures 2, 3 and 4."

Jan 1, 1994