Search Documents

By Kul Bhushan

This paper presents the results of lateral load tests on 0.61-m to 1.27-m (24 to 50-inch) diameter drilled and cast-in-place piers in San Diego area residual/formational soils. The test piers were installed and tested in the following soils: Decomposed Granitic Rock (Ktd), Stadium Conglomerate (Tst), and Friars Formation (Tf). Lateral loads of up to 845 KN (190 kip) were applied to the piers in residual granitic soils, and loads up to 1780 KN (400 kip) were applied to the piers in Stadium Conglomerate and Friars Formation. The tests were conducted by jacking against adjacent piers and monitoring the lateral load and lateral deflection at the ground line. Test results indicate that ultimate lateral pile capacities of up to 1800 KN (400 kip) can be obtained for 0.61 m (24-inch) drilled piers with penetration of 3 to 6 m (10 to 20 ft) in the residual/formational soils tested. Lateral load analyses using p-y curves for very dense sand significantly overestimate the observed lateral deflections. For lateral load analyses using dense sand p-y curves, p-multipliers that increase the lateral soil stiffness (p-y curves) by 2 to 8 times are required to match the load-deflection behavior measured in the test piles. When applied to the dense sand p-y curves, the p-multipliers provide a more accurate prediction of load-deflection behavior in the residual/formational soils, and can result in shorter required pier penetration and significant savings in foundation cost.

Jan 1, 2002

Lignite deposits of Central Otago Miocene Dunstan Formation accumulated on a broad alluvial plain and on deltas that flanked a large freshwater lake. The regional subsurface distribution and configuration of the lignite-bearing strata are identified within the context of depositional systems and placed into a genetically defined stratigraphic framework. The stratigraphic and depositional models constructed, should form an integral part of the geological assessment process to guide future regional or mine based lignite drilling programmes. Further testing and evaluation of the commercialy important lignite deposits in the Blackstone and Roxburgh Coalfields are required to adequately characterise the lignites and their geological setting, particularly to select methods of mining and wise uses of the lignite.

Jan 1, 1992

By C. S. Gibson

"MOST of the mines in the Province of Ontario in Canada are multi-level operations in steeply dipping veins; yet there is an appreciable number whose de-posits are relatively flat-lying, ranging up to 45° inclination.The veins vary in width up to several hundred feet and may or may not be branching systems. The depths of mines range from a few hundred to 8,000 feet, approximately. The primary products of the underground group are asbestos, gold, silver, cobalt, copper, nickel, iron, uranium, talc, fluorspar, gyp-sum and salt.There are a few open-pit mines. The majority are temporary in type because, as the outcrops are removed, mining is continued be-low surface. Primary products of the open pits are copper, nickel, iron, magnesium and nepheline syenite.The industry as a whole employs about 50,000 persons, approximately 60 per •cent of whom have dust-exposure occupations. The definition of a dust-exposure occupation and the requirements for •dealing with same are set forth in The Mining Act of Ontario.Results of extensive and continuing studies on the incidence and progression of silicosis have been reported periodically for years past, in annual reports of the Mines Accident Prevention Association of Ontario and in papers presented at Conferences sponsored by Mcintyre Research Foundation of Toronto, all of which have been published. The information provided therein proves the effectiveness of the means being used to prevent silicosis and allied disorders."

Jan 1, 1960

By M. Gaula

"Gold bearing deposits of the Witwatersrand basin are generally less than 2m thick and require conventional narrow-reef mining methods for extraction and employ explosives as a means of rock breaking. Optimal utilization of explosives is dependent on the overall design of the blast. The under-utilization of explosives arises when shot-holes are drilled inconsistently, overcharged, and when tamping is absent. This can be rectified by emphasizing the importance of good drilling practices as part of induction programmes and refresher courses. The project was aimed at determining whether or not explosives are being optimally utilized at project site. This was investigated through a study of the properties of explosives, mine standards, and recommendations for usage. Underground observations were made to determine whether or not mine standards were being adhered to. Historic data was obtained to establish the historic relationship existing between the quantity of explosives used (kg) and the production output (m2). This was then compared to the quantity of explosives the mine expects to use per unit of production. The results obtained were analysed to determine the presence and extent of over- or under-utilization. It was found that explosives are being under-utilized at the mine. More explosives are ordered than expected per unit of production. The explosives’ properties are not thoroughly exploited during blasting, thereby requiring the use of more explosives than prescribed. Paper written on project work carried out in partial fulfilment of BSc. (Mining Engineering)"

Jan 1, 2015

By G. I. Mathieu, R. W. Bruce

Flotation schemes for the separation of molybdenite from other minerals are based on utilizing the Inherent hydrophobicity of molygdenite (Fuerstenau1). This natural floatability was attributed to the crystalline structure of molybdenite by Gaudin et al.2 who suggested that any surface formed by the rupture of van der Wall's bonds should be hydrophobic and, therefore, naturally floatable. Other authors argued that "natural floatability" is dependent of adsorption of hydrocarbon ions and/or molecu1es on the surface of the minerals. This theory, albeit-c questioned 1,2 has long been recognized in actual practice of molybdenite flotation as the latter in carried out with hydrocarbons, such as fuel oil, kerosene and stove oil. Although conferring ready floatability to molybdenite, these presents generally have little effect on other sulphides and silicates. However, talc is a noteworthy exception because of its innate floatability4. Not withstanding the reason for this behavior which has also been attributed to crystal structure2 its end results as in the case of molybdenite is an immediate flotation response to frothing oils arid kerosene, as was observed by Baranovski5, Sutherland and Wark6.

Jan 1, 1974

By H. P. Hermance

Preliminary examinations of the Parker and Webb deposits were made by E. E. Maillott, Bureau of Mines engineer in July 1942. The chemical and spectrographic analyses included in this report wore made at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., under the general supervision successively of S. M. Shelton and of Paul M. Tyler, formerly regional engineer, Eastern Region. Beneficiation tests were conducted under the supervision of Frank D. Lamb. The mineral exploration was under the general supervision of J. D. Bardill, formerly district engineer. Acknowledgment is gratefully made to the St. Joseph Lead Co., in particular to John S. Brown and P. J. Mechin for their assistance. Special acknowledgment is made to the American Metal Co., Ltd., ,Ind to T. C. Moore for furnishing core-drill and assay data; to the Universal Exploration Co. and P. B. Jennings; and to the Northern New York Mining Corp. and C. H. Sprague for their permission to publish the core-drill dta. Excellent cooperation was given by Dr. W; M. Agar and C, L. Rogers of the Geological Survey.

Jan 1, 1949

By Tae-kyeong Yeu, Jong-Choi, Cheon-Hong Min, Hyung-woo Kim, Jae- Won Oh, Sup Hong, Minuk Lee, Sung-Soon Kim, Chang-Ho Lee, Ki-Young Seong

"Collecting mineral resources from the seabed using a seafloor crawling robot is the firststep in the mining operation. The second-step is lifting the collected ore up to the water surface. For lifting through a riser pipe, prevention of pipe clogging (flow assurance) and economic and eco-friendly up-transferring is of the utmost concern.During collection of mineral ores, the production rate can be highly variable because of the variability in the distribution of the mineral deposit, variations in seafloor topography, fluctuations robot speed, and variations in performance of the mining robot, etc. Direct transfer of the collected ore to the riser pipe might cause unpredictable and serious problems such as over-loading of the lift pump, reduction in the life of the equipment, pipe clogging, severe increase of down-time, critical damage of equipment, further propagation of damages, and total failure after all.As a counter measure to these potential problems, a buffer station has been adopted, which is capable of storing the collected ore for a certain time and simultaneously regulating the transfer of the ore into the riser pipe. A pilot buffer has been developed by KRISO/KIOST (see Fig. 1)."

Sep 1, 2014

By T. M. Barczak

Longwall tailgates in coal mines are often subject to severe mining induced loading and deformation. Innovative tailgate supports have been developed over the years to provide safe and economical access and a ventilation pathway at the tailgate. The support capacity and yield capabilities of the supports need to be matched to the loading imposed by the surrounding rock mass. The ground response curve can be used to represent the rock mass response to mining and its effect on support systems. The FLAC finite difference code was used to supplement field results by simulating a longwall tailgate and the associated ground response. The ground response curve is developed by modeling tailgate excavations with different internal support pressures and recording the resulting convergence. Ground response curves are developed for two typical longwalls operating in the Pittsburgh seam with weak and strong immediate roof. An additional model is presented in which the effect of weak overburden strata is simulated. The ground response is shown to be significantly affected by the strength of the immediate roof as well as the main roof. The importance of yield capacity of standing support is demonstrated. Gob height and compaction are found to affect the amount of convergence in the tailgate. The potential exists to develop site specific tailgate design curves by combining model results with field observations.

Since 2001, the Hybrid Stress Blast Model (HSBM) project members have developed a software suite to model the complete blasting process from non-ideal detonation to muck pile formation. To preserve the physics and improve solution time, the breakage engine uses a combination of analytical models and 2D axisym-metric finite differences to model near-field crushing, coupled to 3D discrete lattice fracturing and distinct element numerical methods to model throw and muck pile development. The model has been validated by comparison with laboratory and field tests in kimberlite. Multiple blasthole simulations are used to demonstrate how changes to blasting parameters can influence downstream efficiencies. Case studies of wall control blasting show that the presplit design must balance the two opposing effects of increased damage with increased charge and decreasing attenuation of the seismic waves with decreasing charge. Modelling of decoupled explosives needs further development. Reducing the charge towards the back of the trim blast results in a much more significant decrease in back damage than altering the timing. The model demonstrates how separation along the weaker planes in a jointed rock can coarsen the fragmentation, leading to inefficient beneficiation, and extends the damage to a distance of at least twice the burden behind from the blasthole, severely compromising the wall stability.

Jan 1, 2012

By P. N. Anyalebechi

The effects of solidification rate on the cast microstructures of aluminum alloys 6009 and 6016 have been investigated with directionally cooled laboratory-size ingots, at 0.2-10.1 K/s and 0.4- 23.1 K/s, respectively. These ranges of solidification rate are within those observed in commercial-size ingots. In both alloys, the average dendrite cell size and second phase particle size decreased with increase in average solidification rate and with a decrease in average local solidification time. However, at comparable solidification rates, the dendrite cells and second phase particles are finer in the shorter freezing range alloy 6009 than in the longer freezing range alloy 6016. This is provisionally attributed to the earlier formation of second phase intermetallics at higher temperatures during solidification and to the formation of greater amount of the relatively coarse plate-like ß -phase (Al9Fe2Si4) phases in alloy 6016. In general, in both alloys, the types and relative amounts of the second phase particles in both alloys are independent of solidification rate.

Jan 1, 2006

By D. Vogt

South African underground hard rock mines are typically managed using measurements made daily, weekly or even monthly of key parameters such as face advance, readiness to blast, blast success, temperature or dust levels. Health, safety and productivity can all be greatly improved if a real-time measurement system can inform decision making. To enable this vision of widespread sensing, communication and decision support, CSIR has developed an open standard architecture for communication of sensor data, and a reference implementation using that standard. The standard, called AziSA, meaning ?to inform? in isiZulu, will allow any device that complies with it to join any network that supports it. The standard is designed for South African gold and platinum mines. To be practical in a typical Bushveld platinum mine, a real-time sensor system needs to be robust, reliable and cheap: ?Sensors are equipped with power sources that will last as long as the sensor is required. In effect, sensors need to be disposable: cheap enough not to warrant repair if they break. ?Communication in the stope is wireless, to avoid there liability problems associated with wire connections. For example, wires to sensors in the face area are unlikely to survive blasting. ?To get information out of the stope, the power line to the scraper winch is used as a communications link. Unlike a separate communications link, the power line will be repaired if damaged, because of its importance to production. ?Outside the stope, communications are transferred onto the mine communication infrastructure. To succeed as a management system, the next key element is the use of software decision support tools that will analyse masses of real-time data to extract key parameters and trends for decision makers. A range of sensors has been developed, including commercial sensors that have had wireless adapters added to make them AziSA compliant, and bespoke sensors that provide low cost sensing of typical mining parameters. An important parameter in any sensor network is the location of the sensor. This has to be easy and cheap to establish, so a tool has been developed to locate sensors in the confines of a stope, using ultrasonic and radio techniques. Once sensors are installed and located, they associate their location to all data that they produce. All the data from the system are captured at surface in a flexible database that can be queried by any application that requires data of any kind. It is simple to program alerts, and for actions to be associated with alerts. The use of wireless in stope also allows for communication from surface to the stope, or from stope to stope. The first implementation of an AziSA compliant system is being installed as part of the Mine Health and Safety Council funded rockfall elimination project. The design is discussed, and a future application for a platinum mine is considered.

Jan 1, 2009

By M. Ahrens, J. Gonser

Gearless mill drives are a well established solution for grinding applications in the minerals and mining industries. The paper describes the functionality and technical features of such drive systems as well as their advantages compared to other drive solutions. Due to the variable speed operation the grinding process can be optimized for ores with varying grinding properties. This leads to significant optimization potential for the plant design as well as for its operation. Furthermore, energy and cost savings due to optimized operation, high system efficiency and high system availability are shown.

Jan 1, 2007

Uranium ore at Sleisbeck, N.T., occurs as lenticular bodies associated with zones of bleached carbonized schists lying between walls of closely folded quartzite. The ore consists mainly of uranium micas with Borne pitchblende.INTRODUCTIONThe Sleisbeck uranium prospect is about 70 miles E. of Pine Creek, and 160 miles S.E. of Darwin (Fig. 1). The prospect consists of a well-defined, E.-W. trending line of hills, about I! miles long. The line is composed of 3 major hills called the Eastern, Central and Western hills, with minor interconnecting hills and outcrops (Fig. 2).

Jan 1, 1955

By P. Foster, A. Burton

Over the past decade there has been a great deal of research into the use of virtual reality (VR) and computer graphics in the mining industry. Much of this has led to developed applications including training simulators and accident re-construction. One other area where there is considerable potential for virtual reality is that of mining ergonomics. This paper identifies those common ergonomic limitations associated with mining equipment that can be effectively modelled using VR techniques. From this, two simple models have been developed namely (i)remote control continuous miner operation and (ii) free steered vehicle sightlines, which demonstrate the practical use of VR in this area.

Jan 1, 2003

By Steve Kral

Led by a surge in coal production and prices in recent years, Colorado’s mining industry is taking part in the same revival as others states and the world. Not too many years ago, the state’s industry was languishing in the same doldrums as the rest of the mining world. Ironic for a state whose history was based on mining. Now, however, Colorado’s mining can boast increased production in all commodities produced, along with prices that allowed companies to expand, increase work forces and post improved shareholder value. So there was a lot of optimism at the Colorado Mining Association’s (CMA) 107th National Western Mining Conference in February. The conference, held in Denver, attracted more than 500 attendees and 39 exhibitors. The theme was Colorado Mines the World.

Jan 1, 2005

By Emmanuel Portilllos

Every paste backfill system is typically unique, this being due to the particular tailings characteristics, the backfill recipe and requirements of mine planning. Key to successful transport to the underground workings through the boreholes and the distribution pipelines is the quality of cemented paste, being free of lumps and recipe components uniformly mixed. Certain types of mixer require that the mixing environment is required to be intensive as possible. In this sense, the present paper point out some of the general aspects of paste plant design, a short discussion on paste recipe and process equipment, followed by a technical comparison between a batch mixing and a continuous mixing process, currently applied to the production of cemented paste tailings for mine backfill.

Sep 9, 2007

Northern Iron Ltd (NIL) is an Australian listed company that recently brought the historic Sydvaranger open pit Magnetite Mine (the Project) in Northern Norway successfully back into production. NIL made the decision to operate the Project on an owner mining basis, due to limited large scale mining expertise amongst Norwegian mining contractors, a long mine life, a limited range in planned mining rate and to minimise costs. As a new mine operator in a country where labour practices are strictly regulated, there was the desire to reduce the risk associated employing and managing skilled personnel. This was achieved by coupling the purchase of the required mining equipment from the original equipment manufacturer's (OEM) regional dealers with OEM supported Maintenance and Repair Contracts (MARC). This paper examines the process that was followed to implement an owner mining operation in a short time frame; approximately 12 months from the initial requests for quotation to actual delivery of mining equipment to site, and some of the challenges faced. By following a formal and well-tested process, not only was the implementation achieved in the set time frame, but significant value was added through the cost savings achieved in the equipment purchase price and MARC rates that were negotiated through this process.

May 1, 2010

By A. A. El-Midany

Traditionally, the choice amongst different upgrading techniques or in finding the optimum operating conditions for a given upgrading technology depends on whether one is looking at the grade or the recovery of the valuable mineral in the concentrate. In fact, the conclusions are not usually the same. This is because the best technique or optimum operating conditions for the highest grade are not the same as the conditions to achieve the maxi-mum recovery. Therefore, a unique measure that takes into consideration both grade and recovery is urgently needed. Finding such a measure is the objective of this paper. A proposed measure provides a selectivity index in the range of 0 to 1, where 0 is no selectivity and 1 is ideal selectivity. The index can be obtained by plotting the so-called Fuerstenau upgrading curve, which relates the recoveries of the components in products of separation and a running regression applying a one-parameter equation. The measure was applied to assess the selectivity of selective flocculation under different operating conditions when used as a sensitive upgrading technique for ultrafine ground ores. After applying the proposed selectivity measure in the case of the selective flocculation of ultrafine Egyptian iron ore without the addition of cations, it was found that the optimum conditions are pH 11, 1 kg/t sodium silicate and 0.4 kg/t potato starch with a selectivity index of 0.55. With the addition of cations, the optimum conditions were found to be pH 11, 1 kg/t sodium silicate and 2 kg/t potato starch with a selectivity index of 0.65. It should be noted that determining these optimum conditions using the traditional grade or recovery measures was highly ambiguous.

Jan 1, 2008

By P. J. Hancox

Heavy mineral deposits have been known from Liberia since the1950s from both river and beach placers. The heavy mineral content of beach sands ranges between 28?62% and the suite includes ilmenite, rutile, zircon and magnetite. These occur together with kyanite, sillimanite, staurolite and garnet. The average ilmenite content is 82% with minor zircon (11%), rutile (6%) and monazite (1%). The ilmenite is, however, of poor quality with haematite intergrowths and a titanium content ranging from10?42.4% (average ±25% TiO2). The amounts of rutile and zircon, while of suitable quality, have also previously been deemed too low for economic exploitation.

Jan 1, 2000

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at tem¬peratures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Forma¬tion changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite.

Jan 1, 2007