Search Documents

By Sastry Putcha, Santosh Mummaneni, Swamy Avasarala, Vamshi Vemula

"This paper presents the results from a case study on the comparison of two strain acquisition instrumentation technologies, Geokon rebar strainmeters and Embedded Data Collectors (EDC) for the DC Water Main Pump Station project, in Washington D.C. These two instrumentation systems were installed by AVER in a single 18-inch (0.45 m) diameter augercast pile (with one-1.25 inch (3.175 cm) dywidag bar) at critical locations to determine the load transfer mechanism and establish a comparison between strain/load measured with these two systems along the pile. A quick static load test was performed on the test pile as per ASTM D1143 standard.Prior to the installation of the pile, a 24-inch (0.6 m) diameter outer casing was installed to the proposed cutoff elevation of -22.5 feet (-6.85 m) to discount the frictional resitance within the upper overburden zone. The pile was then drilled through the outer casing to the tip elevation of -65.02 feet (-19.8 m) with inner casing within the overburden zone. Strainmeters along with EDC were installed on dywidag bar at various locations and then wet set into the concrete following auger retrieval. The loads measured with EDC and Geokon sensors were within 15% percent of each other.PROJECT BACKGROUNDProject Background & Requirements:Like any other foundation piles, augercast piles are extensively used in the public and private sector structures in the United States for many years. It is a common practice to perform static compression (ASTM D1143), tension (ASTM D3689), and lateral load tests (ASTM D3966) depending on the project requirements. In recent years, embedded strain sensors, manufactured by Smart Structures, USA has gained prominence for its use to collect both static and dynamic measurements for driven piles. In addition, AVER has successfully used EDC for collecting long term static measurements for an abutment drilled shafts for I-95 Hotlanes project in Virginia, USA.Geokon sisterbar strain gages are widely used in the foundation industry to monitor the load transfer mechanism within pile foundations throughout the world. As the Geokon strainmeters are vibrating wire and are welded to a sister bar, there is often a debate within the engineering community with regards to what modulus to use when converting measured strains to loads. EDC sensors, unlike Geokon strain gages are embedded directly into the concrete and therefore do not have the same concern."

Jan 1, 1900

By J. T. Nel

The establishment of a pilot plant for the continuous production of titania pigment and nano-titania is discussed. The plant was designed, constructed and operated on the Necsa site. The TiO2 production capacity is 7?10 kg.h-1 by the reaction of TiCl4 and O2at>1000°C. Liquid TiCl4 is sprayed under pressure into a plasma reactor where it evaporates and reacts with O2 to form TiO2. Process optimization has allowed for continuous production without any clogging or blockages. The primary advantage of the plasma-assisted process is the possibility to recover and recycle the chlorine values in high yield as Cl2 for use in the manufacture of TiCl4. The HCl formed in most conventional fossil-fuelled processes makes Cl2 recovery and recycling much more difficult. Particle size distribution analysis of the fine, white product revealed a d50= 125 nm. The raw product consisted of 60% rutile that could be increased to 80?100% rutile by post-annealing. The specific surface area (SSA) of the pigment was 8?20 m2?g-1(BET). According to the CIE colour index the ?whiteness? (L*>95) of the plasma-produced pigment was better than that of several commercially available pigments. The particle size could be manipulated by controlling the TiCl4 feed rate, gas flowrates, and the particle quench rate and residence time. Nano-sized TiO2 powders with a particles size (d50) as small as 50 nm were also successfully produced in this way.

Jan 1, 2010

By M. R. Geer, H. F. Yancey

"INTRODUCTION Throughout the history of coal washing, the jig has been one of the most important coal-cleaning appliances. In 1935 34.7 percent of the 45,361,021 tons of clean coal produced was the product of jigging. 4/ Previous to 1928, most of the jigs used in the United States were of the piston type, with which sufficient mobility to allow stratification in bed is imparted by the reciprocating up-and-down movement of a piston in the water compartment adjacent to the screen compartment. In 1928, the Baum type of jig was introduces in this country and has since come into wide spread use. In this type, water pulsations are imparted by application and release of compressed air to the water compartment. All prior studies of the mechanism of seperating cleared coal from impurity by piston-type jigs. 5/ The same laws of settling, of course, apply to both types, piston or Baum, but the character of the separation with the Baum type may be modified more easily because of the flexibility with which air may be handled, as distinguished from the fixed action of eccentrics commonly used in piston jigs. Since no detailed studies are available to show the performance, that is, the character of the separation between coal and impurity, of the Baum type the Bureau of Mines undertook the investigation recorded in this report."

Jan 1, 1938

The Reefton Goldfield on the West Coast of the South Island of New Zealand was a significant gold producing area between 1860 and 1951. During this period it produced approximately 2.1 million ounces (67 tonnes) of gold. The largest single producer on the goldfield and the deepest mine in New Zealand, was the Blackwater Mine at Waiuta which produced 21 tonnes of gold. The Prolubition Shaft reached a depth of 878 metres (317 metres below sea level). The mine closed suddenly in 1951 with about 66 000 tonnes of are remaining in the stapes. Since closure there has been no attempt to determine the ore potential of the mine at depth. This paper summarises the geology, history and resource potential of the mine and sets out two options for evaluating the remaining resource. The options are either deep drilling from surface or recovery of the Prohibition Shaft and underground development and drilling. A schedule for each option is presented and discussed.

Jan 1, 1992

By J. Dienenthal

Automatic Charging and Stoking Machines for use at ferroalloy furnaces are in operation for more than 20years. Dango & Dienenthal Maschinenbau GmbH (short: DDS) has developed several machine generations. Today advanced solutions help to achieve better charging and stoking results to minimize cost and to improve the working environment around the furnaces. Three different alternatives can be considered: Rail-mounted solution The machine(s) travel(s) on an overhead monorail to one or several furnaces and is locked in the desired working position from where charging and stoking is performed. Mobile solution This machine travels on the charging platform and is also locked at the respective working position to perform charging and stoking. Automation of a standard mobile charging and stoking machine A standard charging and stoking machine can be adapted for automation. A reliable navigation system is included. Charging and stoking is performed with the moving machine. Advantage versus other solutions: considerable lower investment cost and possibility to upgrade the mobile charging and stoking machine for later automation. Overall, automatic charging and stoking can save up to 10 per cent of the specific smelting energy. A better and more consistent furnace operation can be achieved. Different programs are used to cope with different furnace conditions and changing raw materials. All machine movements can be recorded and correlated to other furnace parameters. Working environment on the charging platform is greatly improved.

Jan 1, 2007

By R J. Norris, D J. MacKenzie

Gold-bearing veins have formed at a wide range of depths throughout the uplift history of the Otago Schist. The earliest gold mineralisation occurred during the later stages of Mesozoic metamorphism. This mineralisation was characterised by diffuse wall rock alteration with greenschist facies metamorphic or retrograde metamorphic mineral assemblages, and gold occurs in this altered rock. Quartz veins formed in .steeply dipping extensional fractures associated with this mineralisation type strike north to northeast. The Macraes mine exploits this deposit type. The present northwest strike of the mineralised zone at Macraes is a result of post-mineralisation deformation of the schistosity-parallel mineralised shear zone which hosts northeast striking extensional veins. This combination of schistosity-parallel shear zone and steeply dipping northeast striking veins may exist elsewhere in Otago, and this deposit type is most prospective. Steeply dipping quartz veins formed during post-metamorphic un-roofing of the Otago Schist strike northwest to west and occur as clusters of near-parallel structures in east and central Otago. These veins consist mainly of massive quartz, although some prismatic quartz occurs also. Breccia fragments in veins are common and these are generally silicified, with some gold. Wall rock alteration is negligible, and vein margins are sharp. A set of middle Tertiary veins occurs in northwest Otago. Most of these also strike northwest and dip steeply, but some strike northeast. These veins contain abundant ankeritic carbonate as well as quartz. The carbonate pervades adjacent wall rock as veinlets, but gold mineralisation is confined to veins. Quartz is commonly prismatic and vuggy, and contains gold, which is commonly coarse grained especially in silicified breccia zones. Associated veins contain stibnite. This vein type formed close to the paleosurface (>2 km). Mineralised veins in Marlborough currently strike northwest, but these have been rotated from northeast strike during Alpine Fault displacement of Marlborough from Otago. Some of these veins were formed under late metamorphic conditions and are similar to the north to northeast striking veins in Otago. As in Otago, this type should be considered to be most prospective if they have associated schistosity-parallel shears.

Jan 1, 2000

By Abraham Lindo

"Blasting plays a key role in hard rock underground mining. It is by nature a violent and destructiveextraction method designed to economically fragment the rock into a suitable size for it to be loaded and hauled as part of the specific mining process while controlling the amount of damage to the surrounding rock mass."

Jan 1, 2016

By H Kurth

Geoscan is used for multi-elemental analysis of conveyed bulk materials in real time. It has been used for coal analysis since the 1990s, in the cement industry, and since 2003 for measuring mineral ore quality. Geoscan-M has proven performance and demonstrated paybacks of weeks or months, in iron ore, manganese, copper, zinc-lead and phosphate industries. Geoscan-M measures continuously through the full bed depth and is unaffected by belt speed, particle size, layering and dust levels. Increments of two minutes (typically one to five minutes) are accurately measured and provide the plant operators with tonnage weighted results of each element within seconds.A Geoscan installed after crushing is able to measure quality shortly after mining. The analysis results can be used to divert the increments based on composition, such as diverting waste for disposal and diverting marginal material to a stockpile for processing at a later date. The bulk sorting process allows different qualities to be placed into relevant stockpiles for subsequent blending. Material meeting product DSO (Direct Shipping Ore) quality can bypass a beneficiation circuit to prevent unnecessary treatment costs. An analyser in a blending application enables proportioning of different quality feed materials from multiple stockpiles to achieve a desired compositional consistency for process feed. The parameter used for decisions may be; a) primary metal content, e.g. Cu, Fe, P, etc. b) deleterious component content, e.g. Mg as an indicator of talc content, c) process parameter content, or a combination of these. Process parameter content may be the elemental ratio between critical components, e.g. Cu:S ratio, Fe:Si ratio, basicity, Lime Saturation Factor, etc. or the content of an “indicator” element, e.g. Si as an indicator of material hardness or grindability.Measurement of the composition in real time enables prompt feedback to the mining operators and also feed forward to the process operators. Compositional variability can be critical in the process and advance warning enables appropriate reactions prior to processing. This may include modifying the feed rate, changing the feed blend (through additives), or modifying reagent dosing in anticipation of a change in feed quality. Benefits include, but are not limited to; reducing waste processing, improved feed grade stability, reducing energy, water and grinding media consumption, producing less tailings, increasing process efficiency, higher metal recovery, better plant utilisation, reducing plant downtime, better utilising mined material, all achieved using the same process plant throughput capacity.CITATION:Kurth, H, 2015. Optimising plant feed quality and process performance using Geoscan elemental analysis, in Proceedings MetPlant 2015, pp 373–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By F. Agterberg

In his 1978 monograph ‘Lognormal-de Wijsian Geostatistics for Ore Evaluation’, Professor Danie Krige emphasized the scale-independence of gold and uranium determinations in the Witwatersrand goldfields. It was later established in nonlinear process theory that the original model of de Wijs used by Krige was the earliest example of a multifractal generated by a multiplicative cascade process. Its end product is an assemblage of chemical element concentration values for blocks that are both lognormally distributed and spatially correlated. Variants of de Wijsian geostatistics had already been used by Professor Georges Matheron to explain Krige’s original formula for the relationship between the block variances as well as permanence of frequency distributions for element concentration in blocks of different sizes. Further extensions of this basic approach are concerned with modelling the three-parameter lognormal distribution, the ‘sampling error’, as well as the ‘nugget effect’ and ‘range’ in variogram modelling. This paper is mainly a review of recent multifractal theory, which throws new light on the original findings by Professor Krige on self-similarity of gold and uranium patterns at different scales for blocks of ore by (a) generalizing the original model of de Wijs to account for random cuts; (b) using an accelerated dispersion model to explain the appearance of a third parameter in the lognormal distribution of Witwatersrand gold determinations; and (c) considering that Krige’s sampling error is caused by shape differences between single ore sections and reef areas.

Jan 1, 2015

By H. H. Storch

"INTRODUCTION The first paper of this series contained data concerning the behavior of polyhalite (K2S04.MgS04.2CaS04.2H20) upon calcination and subsequent leaching with water at 100° C. It was found that upon heating polyhalite to temperatures between 298 and 500° C. the water of crystallization is driven off, leaving, an amorphous mixture of K2S04, MgS04, and CaS04. Two transition points were located; one at 298° C. which coincides with the vigorous evolution of steam; and one at 551° C. which results in the formation of a hard mass of crystals. The latter probably consist of a solid solution If the compounds langbeinite (K2504, 2MgS04), potassium dicalcium sulphate (K2304. 2CaS04), and anhydrite (CaS04). The heat of decomposition of polyhalite at 298° C. was measured and found to be 66,000 ± 5,000 calories per mol. The optimum temperature of calcination with regard to subsequent extrac¬tion with two parts of water (at "" 0° C.) is 430 to 450° C. for 65 to 100 mesh material, if one half hour at the calcination temperature is allowed. The maximum concentration of K2S04 obtainable in the extraction of calcined polyhalite is 11.4 grams per 100 grams of water. This concentration of K2304 is considerably above the equilibrium value (3.6 g. per 100 L. of H20 at 83° C.) with respect to the solid phases polyhalite, potassium calcium pentasulphate, ¬and anhydrite. The figure 11.4 K. of K2804 per 100 g. of H20 is also somewhat than the equilibrium value (9,65 g. per 100 g, H20) with respect to the solid phases potassium calcium pentasulphate and syngenite."

Oct 1, 1930

THE present article makes no claim to be exhaustive, since it cannot contain all the knowledge which scientists and manufacturers of the compounds of the rare earths have gained. The following notes are, therefore, simply an attempt to ascertain andclearly record the occurrence, properties, and uses of the more important of the rare earths, with a special reference to their commercial values and the industries based upon them.HISTORYIt was the mine manager, Gcyer, of Stockholm, who, in 1788, first drew attention to a black mineral which had been found in a quarry near Roslagen, in Sweden. In 1805 Klapproth received some specimens of this mineral, which he declared to be a newmineral. Subsequently Gadolin, professor of chemistry at Abo, analyzed the same mineral, and determined the presence of an unknown earth resembling alumina and lime. He named the mineral ytterbite, and afterwards gadolinite. Klapproth has alsothe merit of having detected (1804) another rare earth, which he named ochroit-earth, found in the Bastnas mine, near Riddarhyttan, in Wcstmannland, Sweden. Curiously enough, Hisinger and Berzelius simultaneously ascertained the existence of the same...

Jan 1, 1909

By Larry G. Stolarczyk

Jan 1, 1980

Approximation of Surface Area of Fines in Blast Induced Fragmentation The surface area of fragmentation, especially in the finer size fractions, is a useful property to characterise the mechanisms of rock breakage. In the past, researchers have made assumptions with regard to the shape of fragments in order to estimate surface area, such as that all fragments are the same shape or all fragments are spheres. Often these assumptions were developed with inappropriate measures and returned considerable variability and error for the calculation of surface area. This paper reports a model to estimate fragmentation surface area from sieve sized raw data and a density measurement, with experimental validation down to a size fraction of -45 + 38 ?m in a range of rock types. After characterisation of particle shape, a range of fragment shapes was found to be in each size fraction. Nevertheless, in the ?2 sieve series the average fragment mass, volume and the size fraction standard deviations could be predicted reasonably accurately. Ellipsoid geometry was used to describe particle shape. Using these parameters and the number of fragments (also predicted) in each sieve size the individual surface area of each fragment was simulated.

Sep 13, 2010

By R. L. Fullman, J. W. Cahn

A method is derived for obtaining the distribution of sphere diameters and plate thicknesses (or pearlite spacings) from size distribution functions obtained along randomly oriented lines. The method described offers several advantages over existing methods. IT is often of interest to measure not only the average particle size but also the distribution in sizes of particles dispersed in an opaque material, such as an alloy. Particles of a single size will exhibit a range of apparent sizes on the plane of polish. If the sample contains a distribution of particle sizes, the distribution of observed sizes on the plane of polish is related to the distribution of actual particle sizes by an integral equation, For example, a distribution of sphere sizes, N(r),

Jan 1, 1957

By J. A. Luckmann

"SynopsisThe purpose of this paper is to introduce an innovative approach to risk management in surface mining operations, namely, positive risk. Traditionally, risk management focused on mitigating losses (negative). Positive risk, on the contrary, reverses the approach and focuses on exploiting a project’s inherent benefits (positive).The inability to accurately determine project objectives during the project planning phase and the failure to achieve those objectives during the execution phase is a major problem for any project management in the mining environment.The advance of computer aided design models for mine planning enables mining engineers to examine various options within a very short time. Employing positive risk management combined with drivers-based risk management when evaluating these options provides an ideal opportunity to investigate areas for improving the mining project’s profits. Furthermore, harnessing positive risk returns during the planning phase contributes immensely to the successful achievement of project objectives.Mining has inherent business risks, which can appear overwhelming when considering the risks associated with a mining project schedule, cost, and safety or resources, etc. The question is – how to manage risks in a surface mining environment, and what process methodologies, work methods, processes, and standards should be used when considering the surface mining risks. Applying the principles of positive risk management to manage surface mining risks is not only relevant, but definitely beneficial to mining projects and to the mining industry as a whole.It would be beneficial for risk managers and risk professionals to understand the roles of positive risk ‘drivers’, also known as ‘propitious attractors’. Identifying, analysing, estimating, and understanding the propitious attractors, their behaviour and their influence on project risk events helps considerably during the planning and execution phases. The theoretical and practical knowledge of both sides of the risk – the downside risk (negative risk) and upside risk (positive risk) – can add substantial value to any organization when downside risk is adequately mitigated and upside risk is beneficially exploited."

Jan 1, 2015

By M. S. Smith

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The condition of tunnels at Premier has deteriorated to such an extent that an objective viewpoint on what leads to poor condition was required. Poor and untimely development results in schedule deviation, rehabilitation, and increased working costs. The project focused primarily on quality, and not on efficiency. The project gave management guidelines that need to be focused on in order to produce quality infrastructure. The conclusions were reached by doing literature searches, underground site investigations, benchmarking and computer simulations. From the results we can see that, in order to produce good quality tunnels, we have to have the basics working. This was found to be one of the major problems. Firstly, tunnel profiles are not to the design specification and no fixed blast designs existed. After revising tunnel profile statistics, over break increased to 10% (previously 7%) and development metres were 50 m short of target. Blasting was not monitored and designs not optimized for the conditions. Furthermore, geological factors are the main contributor to tunnel failure, although this process is initiated and aided by poor development (overbroken tunnels, incorrect profiles, direction and location) and blast damage. Continuing to develop tunnels in the current manner will cost R 1.5 million in additional costs for loading and supporting overbreak, whilst an additional 1 800 man-shifts will be required. Blast patterns were designed as a starting point for trials, while the implementation of a blast management system, development statistical database, tunnel hand-over procedures and a revision of the bonus system were proposed.

Jan 1, 2004

By Candice Stevens

The Territory of Afars and Issas is to receive its independence from France on June 27, 1977. The Territory's economic income was based on entrepôt trade through the port of Djibouti and trans-shipment of goods on the Chemin de Fer Franco-Ethiopian (CFE) railroad. The Territorial budget was scheduled to in- crease from $32.6 million3 in 1976 to $36 million in 1977, despite severe shortfalls in 1976 stemming from inflation and a persistent balance-of-trade deficit. Subsidies from France continued to sustain the economy, and the French pledged to provide approximately $140 million in aid annually after independence. In 1976, financial agreements were concluded with a number of Arab oil-producing countries, including Saudi Arabia which granted $10 million toward development projects. The new Republic of Djibouti is scheduled to become the 49th member State of the Organization of African Unity (OAU) and the 21st member of the Arab League, and to receive aid from their financial institutions. The port of Djibouti and the CFE railroad constituted the Territory's main economic resources. Traffic at the port greatly

Jan 1, 1980

By Met B. E

The increasing pace of modern mining makes constantly greater demands upon the several contributing departments of rock breaking and transport, and rock-drilling, as the spearhead of attack, has received a great deal of attention with respect to both machines and steels. By a series of mechanical improvements, combined with the application of selected heat-treated alloy steels, the rock-drill has now been developed into a machine capable of rapid drilling and long service under severe working conditions. As a factoryproduct made under strict metallurgical control it is as foolproof as, say, the modern automobile, and, like its prototype, it can be kept in efficient operation by a minor amount of attention during use and by periodical adjustments and replacements.The same cannot be said, unfortunately, of the drills with which the machine is supplied; in conventional mine-shop practice these are made of the best tool steel shaped and heat-treated under the poorest of metallurgical conditions.The crudities of steel-shop practice have, in fact, always prevented the full exploitation of the steels available at any time, and even at the present day the general standard of treatment offers a contrast with the quality of the steels which moves the metallurgist to amusement, despondency or outrage, according to his temperament. Nevertheless, the tendency persists to meet the increasing demands of the rock-drill primarily by the use of still better steels, and secondarily by improvement, of the steel-shop practice. Athird type of development is the introduction of factorymade tools in the form of detachable bits and rods. It is proposed in this paper to deal with these three aspects of the recent developments in rock-drilling.*Re-written from a lecturette given during the First Ordinary Meeting, 1936.

Jan 1, 1936

The method of investigation was to study the distribution of ore in great detail, to make a thorough structural study of the lode and the mine area, and then to compare the results of the two studies. Such a comparison usually reveals a very close relationship between geological structure and ore distribution, and can often lead to important conclusions which would not be reached in the ordinary working of a mine.The Triton mine lies 30 miles E.N.E. of Cue, or 380 miles N.W. of Kalgoorlie, in typical pre-Cambrian rocks, consisting of gTeenstone lavas and tuft's, interbedded with slates and some sediments, and intruded by granite and porphyry. Fig. 1 (at end of paper) is a longitudinal section of the mine and shows that the workings consist of the main North Emu and the smaller South Emu, separated by a distance of about 1 of a mile. Both orebodies occur on the same lode, which strikes north and south and dips practically vertically. On the same line, and of 1/2 a mile and a mile respectively to the north of the North Emu, are the small Rand and North Rand workings, where a big width of lode material has proved to be very low grade. In the North Emu the lode width averages 12 to 15 feet; it is seldom less than 5 feet and in places reaches 30 feet. In the South Emu the lode is wide, but only portion of it is payable.The lode is a mineralised bed occurring between massive lava flows on the east and a mixed series of tuft's and thin lava flows on the west. The lode material is hard, fine grained, and dark coloured, and generally has a faint banding which is believed to indicate a tuft'aceous origin of the original lode rock. Microscopic examination shows that the original lode rock has undergone considerable albitisation;' there has also been considerable formation of biotite which gives the lode material a characteristic sheen. The mineralisation consists of abundant fine pyrite, which is auriferous, and a lesser development of pyrrhotite which is, however, barren of gold.THE OREBODIES AND THEIR CHARACTERISTICSThe distribution of ore is best studied from gold contours, as these reveal features that cannot be detected in an ordinary assay section. Gold contours (see Fig. 3) are developed' by plotting the width and grade of all development and stoping assays throughout the mine on a longitudinal projection, representing each sample by a coloured dot according to a suitably chosen range of assay values, and then outlining areas of similarly coloured dots (see H. J. C. Conolly, Econ. Geol., April, 1936). Both width and grade must be taken into account and the simplest method of gold contouring is to use dwt.lft. values, but difficulties arise here with big widths of low grade and small widths of high grade ore. To choose an extreme case, 30 ft. of 2 dwts. and 2 ft. of 30 dwts. both equal 60 dwts.lft., and would therefore be given the same value in dwt.lft. contouring...

Jan 1, 1943

By J. B. Gwiazda

S.S. Peng The highlights of this paper are : • The shield supports with lemniscate links will exert a tangential force on the roof strata, causing unnecessary and harmful roof movements, thus damaging the roof structure. The principal source of the tangential force is the horizontal movement of the point O, the pivotal joint between the canopy and the caving shield. When the support height is changed during setting, the point O will move along a curve upward and rearward toward the gob. As a result, it produces a vertical movement, causing the roof to move up a distance of ?d, and a horizontal movement toward the gob, creating vertical fractures in the roof. • The major purpose for employing the lemniscate-link system is to protect the hydraulic legs against the action of the bending moments induced by the tangential force that causes deformation or destruction of the legs. • Based on these two points, the author suggested that, in order to eliminate the harmful effects of the lemniscate-link system and strengthen its advantageous features, a shield support with a new design of that mechanism has been developed. With the new design, the conventional rigid lemniscate links are replaced by hydraulic rams. When the pressure inside the rams reaches a certain level, the ram will yield.

Jan 12, 1986