Search Documents

By Driver R. C, Moelle K. H R

This paper is dedicated to the memory of our friend Peter McKenzie who contributed much to the knowledge of the New South Wales Coalfields.ABSTRACTA fossil river system was recently mapped over parts of the Southern Coalfield, N.S.W. This river system occurs in the roof strata of the Bulli Seam. Sandstone of a fluvial nature was deposited in its course. The sandstone exhibits strong sedimentary vectorial properties and has a marked influence on strata-control in colliery workings.The sedimentary features analysed indicate an approximate S200W flow direction. Petrological studies reveal a clastic, well-cemented sedimentologically and structurally anistropic rock type. Washouts have been found and isopach maps of both sandstone and underlying roof-strata have been compiled. Relevant measurements were carried out in existing colliery workings and on bore cores.Optical determinations of feldspars revealed the presence of plagiocIase feldspars with few exceptions. Most of the feldspars are altered to clay minerals. It was found that a geographical trend exists in the distribution of feldspars, with more basic plagioclase in the northern part of the field.The source area of the fluvial sandstone lies to the north of the Southern Coalfield.Petrofabric analyses were done on several specimens of the fluvial sandstone. In the vicinity of major disturbances, penetrative fabrics were discovered.Calcites (e, 0112), micas (001), and quartz (crystalIo graphic c) show preferred orientations.

Jan 1, 1967

By Timo Kankaanpää

Keywords: Solvent extraction, dispersion, phase separation, CFD The liquid-liquid dispersion phases are separated by gravity in a solvent extraction settler. This separation step is made more effective by picket fences. The picket fence geometry and its physical placement have a significant effect on the separation process, because the purpose of a fence is to smoothen and control organic-aqueous dispersion flow in the first part of the settler and achieve a deep and dense dispersion layer in the front end of the settler resulting in a clean phase separation. In this study, physical phenomena in the solvent extraction process and phase separation in a solvent extraction settler with and without picket fences have been examined using a commercial CFX software package. It can be concluded that the used CFD-approach proved to be a complementary tool for optimizing and designing the solvent extraction settler.

Jan 1, 2005

By A. J. Kraemer

The twenty-fourth of a series of semiannual surveys pertaining to motor gasoline marketed in the United States was made by the Bureau of Mines in August, 1931, The first part of a report giving the results of that survey as they pertain to specification data is given in this paper. A companion report, Part II, is in preparation and will discuss the results off other determinations made on the samples, including octane number ratings on the individual samples (to be made by the Bureau of Standards) and results of the determination of gravity, color, doctor test, and "gum" content by the copper dish method and the Bureau of Mines steam-oven method. The retail price and the tax at the time Each sample was taken will also be retorted. History of Survey The Bureau of Mines made its first survey of motor gasolines sold throughout the United States in 1915,4 a second in 1917,0 and a third in April, 1919.0 These three surveys showed that during each 2-year interval the motor gasoline had become notably less volatile. In order

Jan 1, 1932

By Mario A. Terceros H., K. Rainer Massarsch

"ABSTRACTThe Expander Body (EB) technology has been used successfully to increase the pile toe capacity of bored piles in loose to medium dense soil. An important advantage of the EB system is the ability to monitor the EB expansion process, which provides important information regarding soil strength and soil stiffness. This information, obtained for each installed pile, can be used to determine the actual shape and pile toe area. The expansion pressure can be used to design the pile base capacity.The Expander Body system has been recently improved by incorporating the possibility of post-grouting of the soil below the expanded pile toe. This improvement measure provides additional strength and stiffness to the pile toe and reduces pile settlement.The shaft bearing capacity of bored piles can be increased by using a soil displacement auger, which avoids soil decompression and increases lateral soil stress. This paper describes the principle of the EB system. During the past 20 years, a large number of EB piles have been installed in Bolivia and elsewhere, providing a sound database. Results from field loading tests are presented. A comprehensive study of test piles with and without EB base has been carried out which demonstrates the improvement effects that can be achieved by the EB pile system and the combination with the displacement auger pile method. A design concept for the EB pile system with the full displacement auger pile is presented. A high degree of quality control can be achieved by monitoring the entire pile installation process, including the displacement pile and the Expander Body.1. IntroductionIn many regions of South America, soil deposits consist often of predominantly loose to medium dense sands and silts, often with high groundwater table. In the Santa Cruz area in central Bolivia, such soils are frequently quaternary sediments, deposited by the river Piray. The city of Santa Cruz is located at the right bank of the river.The most common deep foundation method during the last 30 years has been cast in situ piles, augered and concreted under support of bentonite slurry. The design of such piles has been based on SPT results. However, SPT is often performed without quality control and the reliability of geotechnical data is therefore often poor. Traditional methods of pile installation with simple well drilling equipment of insufficient capacity are frequently used. Such methods lack basic requirements of quality control. Such piles have usually low toe resistance and work mainly by shaft resistance . Although the construction process and materials are cheap, the final product has variable and limited capacity. However, the most serious deficiency is that actually achieved pile capacity and pile settlement can be erratic and difficult to predict, leading to uncertainties with regard to actual foundation performance."

Jan 1, 2014

By P Blattner

The Late Miocene gold-silver bearing epithermal system at Waihi has some close similarities in its paleo-thermal and geochemical structure with modern, volcanic-hosted geothermal systems such as Ohaaki-Broadlands. At Waihi an extensive braided quartz vein system is enveloped by hydrothermally altered andesites with minor tuff breccias and tuffs. A main stage of vein filling consists of multiple phases of chalcedonic quartz and fine to medium grained quartz, which are accompanied by pyrite, sphalerite, galena, chalcopyrite and acanthite below the base of oxidation. Platy calcite is present locally. Fluid inclusion studies indicate that the main stage quartz was deposited at temperatures of 189¦-273¦C from dilute (Tm of -0.1 to -1.0¦C) fluids that were locally boiling. Homogenisation temperature Th versus Tm data points lie within the field enveloped by dilution and boiling/gas loss paths determined for the Ohaaki geothermal field, and indicates that the parent hydrothermal fluid for the Waihi epithermal system had a similar composition to that at Ohaaki, ie 0.2 wt% equiv NaCl and 3.3 wt% equiv CO2. The hydrothermal alteration mineralogy and the isotopic composition of vein calcite indicate that the hydrothermal fluid contained relatively high concentrations of CO2 , as at Ohaaki. Oxygen isotope analyses of main stage quartz range from 6.1 to 11.6 %0 and of vein calcite from 2.29 to 9.4%0. Calculated d18Owater values for the hydrothermal fluid that deposited the main stage quartz range from 2.0 to -5.7%0, with a trend to less negative values with depth. They are similar to those in the deep chloride fluid in active geothermal systems with a substantial fluid throughput. A high fluid throughput at Waihi system is also evident from the extensive high intensity hydrothermal alteration and large volume of quartz deposited in the vein system.

Jan 1, 1995

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite with length-to-diameter (L/D) ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite) were tested to failure in axial compression to determine to what extent an increase in end constraint increased compressive strength. Adjustable steel rings, mechanically tightened about the ends of test specimens to create a radial prestress of 3,000 or 5,000 psi prior to the application of axial load, increased end constraint more than was possible in previous tests using solid steel rings. (Solid rings, epoxy-bonded to the ends of dogbone specimens, increased compressive strength compared with that of straight specimens without ring constraint.) During the loading cycle, additional end constraint was produced by lateral expansion of the specimens against the rings. The effect of the end constraint was to increase the compressive strength 55 to 58 percent for the shorter pillars of dogbone shape compared with the compressive strength of straight pillars with the same L/D ratios without ring constraint. Most pillars with L/D ratios of less than 2 were made stronger by end constraint. Pillars with an L/D ratio of 3 did not benefit significantly from end constraint. When the results from compression testing of straight specimens of rock in the laboratory are used to design mine pillars in situ, the pillars will be larger than necessary if the horizontal compressive stress is several thousand pounds per square inch greater than that resulting from the weight of the overlying rock alone. The L/D ratio can be increased by a factor of 1.76 for ratios in the range 0.25 to 3 and still provide the same compressive strength. The safety factor applied with straight specimen test results should also be acceptable for use with constrained pillar test results.

Jan 1, 1969

By P G. Rutherford, A W. McOnie

A volcanic sequence is described from the Golden Cross Mine, Waihi, New Zealand. The sequence includes seven lithostratigraphic units comprising flow and pyroclastic units of Coromandel Group andesite and dacite and overlying Whitianga Group dacite and rhyolite which is intruded by the Golden Cross dacite porphyry and rhyolite dykes. The sequence is mineralised and is unconformably overlain by two post-mineral units, the lacustrine Waitekauri beds and Omahine Subgroup andesite.   Detailed structural analysis of mine data has identified four deformational events (D 1-D4) and related these to the gold-silver mineralising events. Faulting was coeval with the mineralization and directly controlled the development, localisation, style and geometry of the ore shoots. Mineralization developed in competent lithologies where dilation occurred during faulting. The Empire Fault is the master shear which controlled fluid flow. Mineralised veining developed in response to tectonic pulses occurring at slightly different stages as represented by the underground Empire vein complex and the open pit vein array. The mineralising events culminated with the deposition of barren calcite veins. Post-mineral movement along the Western Boundary fault appears to have offset the orebody.

Jan 1, 1995

By L R. Marshall, M J. Rubenach, T G. Blenkinsop, J S. Cleverley

The source and transport regions of fluidised (transported) breccias outcrop in the Cloncurry Fe-oxide-Cu-Au district, providing insights into the origins of other fluidised magmatic-hydrothermal breccias such as kimberlites. Discordant dikes and pipes with rounded clasts of metasedimentary calc-silicate rocks and minor felsic and mafic intrusions extend several kilometres upwards and outwards from the contact aureole of the 1530 Ma Williams Batholith into overlying schists and amphibolites. The brecciation initiated at depths >10 km and may have resulted in surface breaching. We used analytical equations for particle transport to estimate clast velocities (eÆ 20 ms-1), approaching volcanic ejecta rates (up to 80 ms-1). The wide range of CO2 fluid inclusion densities (up to 150 MPa), the localisation of the base of the breccias in contact aureoles, and the scale and discordancy of the bodies suggests the breccia transport process was triggered by an abrupt release of overpressured fluid. At these depths, such extreme behaviour may have been achieved by release of dissolved fluids from crystallising magma, in combination with a strongly fractured and fluid-laden source, sitting under a strong, low permeability barrier, and such parameters may be analogous to the asthenosphere/lithosphere boundary in the case of kimberlite initiation. The relationship of these breccias to the Ernest Henry iron-oxide-Cu-Au deposit suggests they may have been either fertile or æfailedÆ orebody feeders.

Jan 1, 2005

By Sun Jiale

This paper presents a brief description of information construction technology for supported excavation to assure satisfactory performance of engineered system. As a successful example of application of the technique, quite a few troublesome problems, such as high groundwater level in soft ground and crowded buildings around the excavation, were solved satisfactorily in the construction of the new tower of Guangzhou Overseas Chinese Manison.

Jan 1, 1991

By Colin Barratt

The East Side Access (ESA) project is the largest underground rail infrastructure project under construction in New York City, USA. The Manhattan segment of the project is to be mined through rock and consists of 4.1 miles of Tunnel Boring Machine tunnels for track work and mined excavations to house rail switches, air plenums, and other rail facilities. This paper considers different methods for concrete lining, such as the use of fixed forms, adjustable forms, and pneumatically applied shotcrete. The advantages and disadvantages of these methods are discussed and the basis for considering one over the other are illustrated. Further discussions on design development and preparation of documents to facilitate quality and constructability in the field are presented.

By Manuel Gomez

Bituminous coals having maximum fluidity values in the 40- to 25,400-dial-divisions-per-minute (ddpm) range were carbonized in a continuous, entrained-bed reactor. Carbonization was conducted in an 8-inch diameter, vertical reactor at temperatures from 955° to 1,345° F and at air-to-coal ratios ranging from 4.63 to 16.12 scf/lb of moisture-and ash-free coal charged. Carbonization rates from about 118 to 360 lb/hr, as-carbonized basis, were examined. It was demonstrated that carbonization temperature and air-to-coal ratio must exceed minimum values for continuous operation. Within the operating conditions discussed, highly fluid bituminous coal was carbonized to produce tar and nonagglomerated char. The yield of tar ranged from 21.3 to 38.9 gallons per ton and the char yield ranged from 1,109 to 1,563 pounds per ton, all units expressed on a moisture-and ash-free basis. It was demonstrated that the maximum fluidity and the average size of the coal along with the air-to-coal ratio and the carbonization temperature act together to influence the carbonization product yields and certain properties of the products. Prediction equations were developed from the data for product yields and selected properties of the char, tar, and gas.

Jan 1, 1968

By John R. Bartels

This U.S. Bureau of Mines report describes the development, system by system evaluation, and preliminary surface testing of a flywheel-powered shuttle car (FPSC). The use of a self-contained flywheel-power source has the potential to eliminate the numerous safety and routing problems associated with tethered mobile equipment. An alternative to conventional power cable systems was developed consisting of the world's fIrst seven-rotor stacked flywheel system capable of storing 6 kW·h of energy at 16,700 rpm. Numerous interdependent systems were necessary for successful interfacing with a conventional shuttle car. Each of these systems was evaluated and tested individually. Finally, the entire shuttle car was surface tested. The tests indicated that the flywheel energy system can function and operate a shuttle car. The economics of the system and the design of required support systems were not addressed in the project.

Jan 1, 1991

[Thin roport. C"WAW; I Ac rvq"I LN 01 a tvchniv&ll nnd oco I in j ;- I iv It i on c)l roncc p Ln,I I Lc!iin I OV Lhe undprnro"nd vNing, ruh h! i zn(kn, And 1" viiii rutoriin- of Opp &L :;halo drponi1q. Study L-I 10 1 1:; ..vi c I i rst d it cc tvd L ""Ards "vA I "it Wit "I the ippLWAhle q(t)¬logy, .in:;"(OLud ;hintvirak, r"ck muchnnics, ii; Olu rolturving, acum; mining, votitiInthn, iiiHtl I' it inn, vaFrry, :ind nn': iru"muniAl iNpiet InvI ors ConroptuAl mv:Lvmn wore nv"tWqjW rind Wen ovALUOILed agalnSt I lIt"n I it' 1 ttCS I runt ho I I I ;I I cc!ii i (.:I I A I I( I ocon "mi t?. vivwpn Lnt . Thu I CS" ICS 01 Lhunv vv&"Mions wpru thun ;lira ly-Ptl ind, KNqwd upon this analls is , hit foll"wkg two syntvmn writ' 5VIecLind lor furLhpu study in Phaso Ll: 4 -Ili I I : kcoiii nid Pi I lair -Art ica L DrL I I and Blasr SyKyw 1V: THOW Hori"g-Horiz"nuaL Ring Drill anti BI-ast Thiq rvpnrL is nahmillrd in fulAllarrit or We Phzni, J parLion ul (Arnt KICL Oinhou SON LO/ 1 by Nni x & Kc Won , I nc. Co thp D. nvor Rostnrch Cvntpr, Uni-LPd AL"tpn DWPAUxiont of the InLerilor, QUrCJlH of Mines. Ark wns tonpirrind as of March, 1979.]

Jan 1, 1975

By Bradley V. Johnson, Robert J. Timko, Edward D. Thimons

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has researched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1987

By B. Gazea, A. Kontopoulos, A. Kourtis, K. Adam

Static tests give a measure of the balance between acid-producing and acid-neutralising mineral components in a material, while kinetic tests determine acid generation and neutralisation over a long period. Drill-core samples from the amphibolite and gneiss host rocks of the Stratoni lead-zinc sulphide deposit in Greece and mine/mill waste samples from Stratoni and Olympias were examined by the standard acid base accounting, BCR and net acid production tests. Mineralogical data on the materials and resulting residues were used to illustrate the differences between the methods and establish their ranges of applicability. BCR seems to simulate most closely the conditions prevailing during generation of acid mine drainage but is time-consuming and requires elaborate equipment. Acid base accounting is suggested for standard screening; net acid production might be used in the field or for solids with less than 10% S

Jun 19, 1905

By Jason Ryan, Stephen Harria

Q.E.D. (QED) is a blast design and evaluation model that allows full three-dimensional design specification including the development of unique “live” terrains and an unlimited variety of complex charge configurations. QED’s analysis package allows the examination of likely outcomes resulting from changing various design variables in terms of vibration, fragmentation, rock-mass damage and muck-pile profile. Especially applicable to use cautious blasting applications, QED’s damage model uses vibration to estimate rock damage beyond excavation boundaries. This relates directly to operations such as Yucca Mountain Nuclear Waste Repository in Nevada, where damage beyond the excavation perimeter must be tightly controlled. The U.S. Department of Energy (DOE) h as b een studying a site at Yucca Mountain, NV to determine its suitability for long term storage of nuclear waste. The main mechanism of waste isolation will be the natural barrier of the host rock Total Systems Performance Assessment (ISPA) is used to model the excavation design and its behavior over time. Of importance to TSPA is quantifying the condition of the rock-mass before and after excavation. Ideally, there should be no excavation-induced changes to the rock-mass’ structure (removing the requirement to model the effects). At the least it may be possible to keep excavation-induced damage far enough away from waste packages so that modeling of these effects will not be required. QED can calculate a prediction of the extents of blast induced damage to the rock-mass. By using this metric as a design parameter, it may be possible to complete excavation of the repository more rapidly and inexpensively than previously thought, without jeopardizing the structural integrity of the waste containment areas or requiring blast damage to be modeled by the TSPA. This paper will explain the structure of the QED blast modeling system and show the analysis of historical data from Yucca Mountain. Processing of the historical data and the subsequent results will demonstrate how blast modeling can be used on an ongoing basis to assist the excavation process at Yucca Mountain.

Jan 1, 2000

By Cadia Geology Team

The Cadia Hill Gold Mine, located near Orange in Central Western New South Wales, is owned and operated by Cadia Holdings Pty Ltd, a wholly owned subsidiary of Newcrest Mining Limited. Construction including pre-strip mining occurred from 1996 to 1998. The mine was officially opened in October 1998 following commissioning of the concentrator and mine fleet in June of that year. The Cadia Hill orebody is a porphyry related gold and copper system. The final pit has a strip ratio of approximately 1.3:1.0. Mining is undertaken on 15 metre benches using large capacity diesel hydraulic face shovels at an annualised rate of up to 70 Mtpa. The concentrator is currently rated at 17Mtpa and includes the worldÆs largest single line grinding circuit. The feasibility Mineral Resource was estimated at 352 Mt at 0.63 g/t Au and 0.17 per cent Cu. Initial reserves totalled 200 Mt at 0.74 g/t Au and 0.17 per cent Cu yielding a mine life of approximately 12 years. During the pre-production period mine geology systems were developed to support the operation. By design these systems were intended to add value to the business through minimisation of material miss-classification, provision of accurate and timely production information and mapping and reconciliation as a continuous model improvement tool. Variances that would prove to be material to the life of mine plan were recognised during the first year of production. These included identification of additional ore tonnes, higher copper grades and higher gold recoveries relative to the model. Gold grades and copper recoveries also reconciled favourably. Testwork was undertaken to determine the underlying causes of each variance. Re-modelling was then undertaken to capitalise on those variances. The Cadia Hill Gold Mine life of mine plan was re-evaluated with updated geology, grade, geotechnical, metallurgical and environmental inputs. Operating strategies were also reviewed and revised. Despite application of reduced metal prices in the evaluation, the outcome was one of extended mine life with more metal produced at lower cost. Development of robust mine geology systems, including a pro-active reconciliation process contributed to tangible improvement of the Cadia Hill Gold Mine operation. On-going system development and improvement initiatives are planned to add further value for the future.

Jan 1, 2000

By G McMillan, P Mulvey

"Geochemical characterisation is done based upon the geology and metallurgical batch testing prior to commencement of the operation of the plant.  Tailings repository design is based upon geochemical assessment of the waste material, as well as the geomechanical issues associated with storing the waste. The resultant conceptual and detailed design is incorporated into the environmental impact statement (EIS), upon which mine approval is based. The entire environmental monitoring and harm mitigation program, which is usually a condition of the Mine Lease approval, is based upon the applicability of the original characterisation.Tacit to this process is that there is no change in the geochemistry of the tailings, i.e. no change in the implications for acid & metalliferous or saline/neutral mine drainage (AMD/SNMD) generation. But any changes in milling and processing can have a substantive impact on the geochemical behaviour of the tailings metallurgy, and potentially render an operation non-compliant within the conditions of the mine license.Environmental and statutory approval implications for continuous improvements of metallurgy need to be understood because unintended consequences could cost more than the benefits of the improvement, and in some cases cost more than all the profit made from the mine.  Examples uncovered during audit and consultant practice will be presented together with a process to ensure implications for adverse environmental harm and license conditions are fully considered.*This paper is only available for individual download. It is not included in the conference proceedings*CITATION:Mulvey, P, 2013. Continuous improvement - how changes in metallurgy can have a substantive impact on environmental impact and closure - lessons learnt from environmental auditing, presented to MetPlant 2013 Conference (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By Z. Sun

Imposing a strong magnetic field is considered to be an attractive method to prepare materials with aligned or textured structures due to its intrinsic properties, e.g. non-contact and easily controllable. However, the nature of the strong magnetic field effect still remains unclear and further research is needed. In the present paper, the effect of a strong magnetic field on the solidification of a hypereutectic Al-Cu alloy was investigated. After magnetic field treatment, the primary phase was aligned parallel to the magnetic field direction. Meanwhile, the eutectic micro-structural constituent became elongated and thinner. A theoretical analysis was conducted to have a better understanding of the phenomena. During solidification, the magnetic Faraday and dipole-dipole interaction forces are considered to decrease the solute pile-up in front of the solid-liquid interface and modify the eutectic cell formation. The alignment of the phase is due to the shape magnetic anisotropy and crystal magnetic anisotropy.

Jan 1, 2010

By Michael Young, Peter Allum, Mingwei Gao

"Tough economical conditions and high grade but fine-grained ore processing have forced the mining industry to look for more efficient processes. Isa Mill Technology for ultra-fine and fine grinding is one such process employed at several mining operations in Australia including Mount Isa Mines Limited in Australia. Mount Isa Mines is a business unit of MIM Holdings Limited. MIM is an Australian-based international mining and mineral processing company with around 8000 employees worldwide. Major products include copper, gold, zinc-lead-silver, coal and technology sales.The Isa Mill is a horizontal stirred mill with sizes up to 3 m3 chamber net volume and 1 120 kW installed motor. It was jointly invented by Mount Isa Mines of Australia and Netzsch Feinmahltecknik GmbH of Germany for ultra-fine and fine grinding duties in the minerals industry. Isa Mill operations started in 1994 at the Mount Isa Mines Leadzinc Concentrator and then at MIM’s McArthur River Mine in 1995. These Isa Mills have been used to liberate sphalerite and galena at Mount Isa and silica at McArthur River by grinding to less than 7 micron.This paper discusses the Isa Mill Technology and reports on the metallurgical performance of the Isa Mills at Mount Isa Mines, including work done over the last 9 years to improve mill design, process efficiency and maintenance, which has resulted in the current state-of-the-art Isa Mill Technology.INTRODUCTIONThe current leadzinc deposits at Mount Isa Mines (George Fisher, Hilton and Isa) have an average grade of 10.5% zinc, 7.2% lead and 165g/t silver. Fine grinding, in particular in the zinc retreatment circuit requiring a milled product P80 of 7 micron, is essential to treat the ores from the Mount Isa Mines deposits. Every one micron size reduction in the zinc retreatment circuit below a P80 of 10 micron improves the overall plant zinc recovery by 1%, resulting in an increase in revenue of about 1 million dollars per annum."

Jan 1, 2002