Search Documents

The National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine the effectiveness of a filtered air delivery system to reduce respirable dust exposure to roof bolter operators in underground coal mines. When performing roof bolting operations, roof bolter operators may experience exposure to high levels of respirable dust during a working shift, especially when working downwind of the continuous mining machine. While drilling and installing roof bolts, this filtered air system supplies a clean curtain of air over the roof bolter operator by means of a plenum mounted beneath the canopy. This experimentally designed air curtain, adapted for roof bolting machines used in this study, is based upon previous design prototypes, computational fluid dynamics (CFD) simulations, and trial-and-error testing. Both prototype and final designs were tested in the full-scale mining galleries at the Office of Mine Safety and Health Research (OMSHR) in Pittsburgh before being taken underground for field testing. Test results of the system in both laboratory and field studies show reductions in operator exposure to respirable dust when the operator is positioned directly under the protected zone of the canopy.

Jan 1, 2012

By E. M. Shemang, C. E. Suh, L. Mbinkar, University of Yaounde

"Two iron deposits within the Precambrian mineral belt of Cameroon are described in detail for the first time: the Archean Metzimevin replacement iron deposit enclosed in Fe-enriched itabirite, and the Proterozoic granite-hosted, shear zone-related Mayo Binka magnetite deposit. In the Metzimevin de¬posit, quartz is corroded and microplaty hematite overprints martite-textured hematite. The Mayo Binka massive magnetite veins show evidence of deformation in magnetite (fracturing and microbrecciation) and in overgrowths of specular hematite (mechanical twinning and undulating extinction). The magnetite is partially replaced by hematite (martitization) and goethite. Ores from both deposits have >88% total Fe2O3 and low contents of contaminants such as SiO2, Al2O3, MgO, CaO, P2O5, and TiO2. They are also poor in Cu, Pb, Zn, V, Cr, and Ni. The Metzimevin massive hematite is characterized by an accentuated light rare earth element depletion relative to the Fe-enriched itabirite. It is suggested that the Metzimevin iron deposit is the result of hypogene leaching of gangue minerals from, and further hematitization of, an itabirite protore. Although the genesis of the Mayo Binka massive magnetite is unclear, it is spatially related to Neoproterozoic granitic rocks. The data allow some comparison of these little known, but pot¬entially economic iron deposits, with some of the world’s better investigated deposits, and are useful to the exploration efforts for iron ore currently underway in Cameroon and the Central African subregion.Deux gisements de fer de la ceinture minérale Précambrienne du Cameroun sont ici décrits en détail pour la première fois : le gisement de fer Archéen de Metzimevin formé par remplacement et encaissé par des itabirites enrichies en Fe, et le gisement de magnétite Protérozoïque de Mayo Binka as¬socié au cisaillement dans un granite. Au gisement de Metzimevin, le quartz est corrodé et de l’hématite en microplaquettes se développe au dépends de l’hématite a texture martitique. Les veines de magné¬tite massive de Mayo Binka présentent des évidences de déformation dans la magnétite (fracturation et microbréchification) et dans les surcroissances d’hématite spéculaire (Macles tectoniques et extinction ondulante). La magnétite est partiellement remplacée par l’hématite (martitisation) et par la goethite. Le minerai des deux gisements contient >88% de Fe2O3 total et un faible contenu en contaminants tels que SiO2, Al2O3, MgO, CaO, P2O5, et TiO2. Il est également pauvre en Cu, en Pb, en Zn, en V, en Cr et en Ni. L’hématite massive de Metzimevin est caractérisée par un appauvrissement relatif en terres rares légères relativement à l’itabirite enrichie en Fe. Il est suggéré que le gisement de fer de Metzimevin résulte du les¬sivage hypogène des minéraux de la gangue ainsi que de l’hématitisation poussée d’une préconcentration de fer dans l’itabirite. Bien que la genèse de la magnétite massive de Mayo Binka demeure obscure, elle est spatialement associée aux roches granitiques Néoprotérozoiques. Ces données permettent de comparer ces gisements de fer peu connus et potentiellement économiques avec certains des gisements mondiale¬ment mieux connus, aidant ainsi les efforts d’exploration présentement en cours en Afrique de l’ouest et au Cameroun."

Jan 1, 2008

By Roberto J. Guardia, Tim Shell, Robert A. Robinson, Steve Rodolf

Our aging infrastructure includes numerous tunnels that provide easy access through topographic and societal obstacles. These tunnels are renewable resources that require periodic maintenance and rehabilitation to extend their useful lifespan to hundreds or even thousands of years. However, as with any structural rehabilitation project, tunnel liner rehabilitation requires an inordinate amount of evaluation and care due often poorly documented original construction and subsequent repair construction methods and materials. This paper documents the investigation, planning, design, and construction efforts of the rehabilitation of a 74-year old, 216-meter (713 foot) long two-lane highway tunnel in moderately fractured to highly sheared basalt on the Oregon coast. The tunnel consists of four sections lined originally with timber and subsequently overlaid with concrete, and three unlined sections.

Jan 1, 2005

Study on Mineral Processing of Refractory Copper-Nickel Ore

Sep 13, 2010

By Verne E. Hooker

This Bureau of Mines report summarizes the results of modifications in the borehole deformation gage design and subsequent changes in the overcoring techniques. Modifications in the borehole deformation gage have greatly improved the creep characteristics and enhanced the versatility of the gage. In situ field tests in competent rock near St. Cloud, Minn., provided sufficient data to compare the reliability between gages and new techniques in obtaining good engineering estimates of stresses. Near-surface horizontal stresses at the test sites are compressive and biaxial in nature.

Jan 1, 1974

By Anil K. Ray

Roof falls are one of the greatest hazards in underground coal mines worldwide. Due to stringent safety measures and extensive support system development, roof falls have been reduced significantly but they still persist in many underground coal mines. Some of the roof falls initiate with cutter roof or guttering. In the past, many factors have been identified as being responsible for the development of cutters and roof fall. These responsible factors can be broadly classified as stress related or non-stress related. In this paper the finer details of mining technique have been taken into consideration for better understanding of cutter roof and roof fall problems. Three dimensional finite difference modeling has been used to explain the mechanism of cutter development. Strain softening material behavior has been used to realistically simulate the cutter formation, and common cutting sequences as implemented in the field have been simulated. This was done with an objective to determine whether the cutting sequence has really any significant control over cutter formation or not. In addition to cutting sequences, the effect of cut length is also studied. The effect of step cutting and turning of crosscut into and away from major and minor horizontal stresses is also examined to see its influence on cutter development.

Jan 1, 2009

As part of the Bureau of Mines program to reduce U.S. reliance on foreign suppliers of strategic and critical metals, research was conducted to improve technology for the recovery of critical metals from hardface alloy grinding waste, a form of superalloy scrap. This report describes a hydrometallurgical process that demonstrated on a laboratory scale that 79 pct of the chromium, 97 pct of the cobalt, 99 pct of the manganese, 99 pct of the nickel, and 90 pct of the tungsten could be recovered in chemical form from hardface alloy grinding waste. The process involved deoiling the grinding waste, followed by chloride-based dissolution of the deoiled material. A high-grade calcium tungstate (CaW04) product was recovered from the resultant leach residue by caustic leaching and precipitation. Iron, cobalt, man-ganese, and nickel chlorides were sequentially recovered from the leach liquor by solvent extraction. Amine extractants were used to extract the iron, cobalt, and manganese; decanal oxime was used to extract the nickel. Market-grade cobalt chloride (CoCI2), manganese chloride (MnC12), and nickel chloride (NiCl2) products could be produced directly from the resultant strip liquors. The final raffrnate was a relatively pure chromic chloride (CrCI3) solution that compared favorably with commercial solutions.

Jan 1, 1988

By W Donovan

Concern exists about the potential release of metals from the proposed mining operation at Martha Hill to the Ohinemuri River. Speculation on possible impacts is fuelled by the dearth of published data on existing metal levels not only for this river system but for streams throughout the Coromandel. At first sight this lack of data is surprising given the apparent interest in this subject and the fact that future mining activity in this region has been a possibility since at least 1979. That such a situation has arisen is not altogether unexpected given the difficulties faced by various organisations, including the mining industry, in determining metal levels which are generally acknowledged to be low. This paper presents data for a number of stations in the vicinity of the proposed operation; it explains the analytical procedures which were adopted and the rationale for them and relates the information which has been obtained to water quality criteria.

Jan 1, 1986

By E. J. Gleim

An important phase in the Bureau of Mines investigation of electrical machines designed for operation in gassy coal mines is testing enclosures of electrical components for explosion-proof qualities. In brief, this testing consists of filling and surrounding the enclosure with an explosive atmosphere of methane and air and then igniting the atmosphere within the enclosure to determine (1) Whether the resulting explosion is confined without discharge of flame; (2) whether the enclosure walls are permanently distorted; and (3) whether excessive pressures are developed within the enclosure. Ordinarily, the pressures encountered in routine testing do not exceed 100 pounds per square inch gage. Hence, the designer of the machine does not have too much difficulty in taking corrective measures to prevent flame discharge and distortion of the enclosure. Occasionally, however, the explosion pressures greatly exceed 100 pounds. Then the goblet of the designer may not be solved so readily, From experience over the year 0, the testing personnel often can predict that certain construction will result in high. Pressures, but, only in a very general way, has it been possible to advise designers what modifications might be made to reduce the explosion pressures to normal values. For example, if high pressures were developed in a motor starter having a partition with an opening through it, some enlargement of the opening may appear to be the logical procedure, but it has not been- possible to give information concerning the exact amount the opening should be enlarged to prevent development of high pressures .

Jan 1, 1952

By Glen Church, Don W. Deere, Christoph M. Goss

The Standley Lake Dam Rehabilitation Project in Colorado included the complete replacement of the outlet works. This required two 1.8m (6 ft) diameter microtunneled wet lake taps, 380m and 186m (1246 ft and 636 ft) long, a permanent valve shaft 12.2m(40 ft) wide and 32m (105 ft) deep, and a 3.5m (11.5 ft) diameter (962 foot long) outlet tunnel driven with a roadheader. The tunnels were driven in low-strength, expansive, and slickensided claystone. The paper addresses the site investigation, shaft construction, roadheader performance, shotcrete placement, tunnel convergence, long distance microtunneling, and wet lake taps.

Jan 1, 2005

Estimating Particle Size Fraction Proportions - A Multiscale Approach Using Multiple Kernel Learning

Sep 13, 2010

By B. C. Viljoen

"SynopsisCommencement of the next phase of the Lesotho Highlands Water Project is a year or so away from becoming reality. Some 50 km of tunnels in the form of access adits, shafts, diversion tunnels, and main waterways will be constructed. Sprayed concrete will form an integral part of the temporary and permanent rock support systems that will be installed. Furthermore, the use of sprayed concrete as a final tunnel lining solution was proposed as a viable alternative to concrete linings in the feasibility studies that preceded the forthcoming implementation phase.The aim of this paper is to make the reader aware of all the sprayed concrete related issues that engineers tend to grapple with during the design and construction of tunnel projects and other underground works. Primarily, these issues would include selection of applicable design parameters, technical specifications, construction application methods, quality control and, most importantly in the context of final or permanent linings, the durability of sprayed concrete.The International Tunnelling Association (ITA) Working Group (WG) 12 has been tasked specifically to publish a set of recommendations on the Quality and Control of the Application of Sprayed Concrete and the Testing of Sprayed Concrete for Durability. These tasks were also further explored at the recent World Tunnel Congress (WTC 2015) that was held in Dubrovnik, Croatia at the end of May 2015.IntroductionSprayed concrete is presented in a variety of shapes, designs, forms, application methods and accompanying terminologies including shotcrete, gunite, pneumatically applied concrete, and the like. The International Tunnelling Association (ITA) decided to standardize on a single terminology, namely ‘sprayed concrete’, in order to simplify specification, interpretation of guidelines, and codes of practice."

Jan 1, 2015

By Paul G. Swanson

This investigation was conducted to identify the principle causes of spoil instability problems in the Eastern Coal Province. The study was also conducted to develop a matrix to predict the strength and groundwater parameters necessary to conduct stability analyses on a proposed reclamation scheme. Suggestive methods to reduce spoil instability potential are also included. Numerous physical property, strength, compressibility, chemical and mineralogical tests were conducted on mine spoil samples obtained from 11 different surface mine sites. Site characteristics that influence the position of the post reclamation groundwater table were identified. Distinct regions within the Eastern Coal Province with high incidences of surface mine slides or high landslide susceptibility were identified. The application of the predictive matrices developed in this study is for surface mine sites mined and reclaimed in general accordance with the Surface Mine Reclamation Control Act of 1977. A review of current mining practices and the relative effect on spoil stability is included.

Jan 1, 1983

By D. E. Sherwood

Recent developments in high torque hydraulic rotary rigs has lead to the construction of secant bored pile walls by rotary drilling methods in circumstances where earlier methods were difficult and in some cases impossible. The evolution of secant bored pile wall construction is described including classical, rotary drilled and continuous flight auger construction methods. The paper then details the restraints which have been created in recent inner city redevelopment, many of which were not relevant in the early days of the technique. Typical examples of walls are presented to show the adapatability and advantages of the secant bored pile wall method. A number of in-situ retaining wall construction techniques are then compared in detail with regard to relative cost, technical quality and practicality.

Jan 1, 1989

By George Comstock

IT seems a common opinion among metallographists that all light-gray inclusions seen with the microscope in polished sections of steel are manganese sulphide. Examples of this belief are continually appearing, as for instance in the paper by Dr. Henry Fay on manganese sulphide as a source of danger in steel rails,1 and in Lieutenant-Commander Cook's paper on Metallography of Steel for U S. Naval Ordnance.2 Slate FIG. 1-TRANSVERSE VIEW OF THE EDGE OF A SMALL HOT-ROLLED STEEL ROD. ETCHED WITH PICRIC ACID. X 200. colored inclusions are considered to be silicates, and dove-gray inclusions, manganese sulphide. To show the danger in the latter unqualified assumption, it should be sufficient to examine the edge of any piece of steel that is covered with a fairly thick scale, and that has been polished in such a way as to prevent the scale from breaking away entirely below the polished surface. This can be done by protecting the scaled edge of

Jan 12, 1916

By Tatsuo Itou

Both sales volume of Aluminum Can and its recycling rate are remarkably increasing here in Japan. In 1993, recycled can volume was 11.78 billion cans ( 116,258 metric tons ) and its recycling rate 57.8 percent. We, MITSUBISHI MATERIALS CORPORATION. the leading manufacturer of aluminum can in Japan and our affiliated companies are very deeply involved in recycling used beverage cans ( U.B.C ) and recycling them back to can stock. In this paper. I would like to present the following; 1. Recent trend of beverage can consumption in Japan. 2. Trend of aluminum can and its recycling rate in Japan. 3. Future of aluminum can business in Japan.

Jan 1, 1995

By Lulie H. Crump

Salient information on reserves, production, and consumption of fuels and energy by State is summarized in this Bureau of Mines publication. Reserve and production data are shown for each of the fossil fuels (coal, crude oil, natural gas liquids, and natural gas) and for uranium. The consumption data of each of the major consuming sectors (household-commercial, industrial, transportation, electric power, and miscellaneous) are broken down by energy source (coal, petroleum, natural gas, hydropower, and nuclear). In addition, total energy consumption in the Nation in 1973 is compared with consumption in 1972 and 1974 (preliminary data).

Jan 1, 1976

By Marcus A. Wiley, Gregory Abramov

Borehole mining (BHM) is a remotely operated method of extracting rock material through boreholes by high-pressure water jets. Figure 1 illustrates a BHM tool and fluids circulation. The tool consists of at least two pipes, one for pumping down high-pressure water, the second for delivering slurry to the surface. This article reviews the BHM process. It discusses current and new applications for borehole mining and help the readers determine if BHM is applicable in their situations. Previous articles in ME about BHM explained either a particular project (ME, April 2001, pp. 33-36) or a newest patent in this area (ME, March 1991, pp. 313-318). However, neither one provided an overview on the modern BHM technology.

Jan 1, 2004

By E. P. Ferrero

Crude oils from fields throughout the world are analyzed by the Bureau of Mines to determine the characteristics of the oils and their contribution to the petroleum resources of the world. Analyses are reported for 169 foreign crude oil samples from 122 oilfields in Africa, Asia, Australia, the Caribbean, Europe, North America, and South America. Tables show the geographic and geo- logic origin of the samples, names of companies that supplied the samples, annual production for the fields, general characteristics and analytical and computed data, hydrocarbon-type data, cumulative production of the larger fields, and references to sources of geological and field development information. The analyses were made by the Bureau of Mines routine method and comparisons may be made with more than 8,000 other such analyses.

Jan 1, 1972

By Paul H. Madsen, Victor S. Romero

The Tren Urbano project in Puerto Rico includes a 19 m diameter tunnel constructed by the stacked drift method, which involves installation of a pre-supported concrete arch using multiple tunnels. Geotechnical conditions consisted of weak rock and highly weathered, unstable alluvial soils. Due to low cover, reinforcement of the arch was required. Ground behavior ranged from firm ground to mixed-face to raveling and flowing ground. Consequently, construction of the individual drifts involved many different soft-ground techniques such as steel set supports, shotcrete support, shield tunneling, forepoling, and consolidation grouting. During construction, the design was modified to improve constructability. Although settlement was experienced during excavation of the drifts, arch movements were within predicted limits and minimal surface settlement was observed upon excavation of the interior.

Jan 1, 2001