Search Documents

By J. R. Thoenen

For several years the Bureau of mines has been investigating the characteristics of ground vibrations produced by quarry blasts. Considerable basic information has been obtained in the course of this study, and the results have been made known to the public through various publications listed in the accompanying bibliography The studies have been confined to obtaining fundamental knowledge of the characteristics of the vibrations themselves, because it was evident at once that he problem was extremely complicated. It was felt that any attempt to predict the effect of a ground vibration on any type of artificial structure would be useless until the complexities of building vibrations are better understood. As opportunity offered, teats wore made in various types of structures and the effects of vibrations from many different sources were measured. In one set of tests (5)4/, it was demonstrated that the behavior of a building as quite different if it was shaken by vibrations originating outside tae foundation walls than if the source of the vibrations was within the building; vibrations coming from the ground outside seemed to shake the building as a single, loosely-coupled structure, whereas mechanically induced vibrations within the house seemed to set floors and walls in motion as independent units, each of which communicated its own natural motion to the adjoining member, causing a very complicated movement that was impossible to interpret.

Jan 1, 1938

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminick, D. Evans-Lamswood

"Abstract — Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite."

Jan 1, 2012

By J. R. Thoenen

For several years the Bureau of mines has been investigating the characteristics of ground vibrations produced by quarry blasts. Considerable basic information has been obtained in the course of this study, and the results have been made known to the public through various publications listed in the accompanying bibliography. The studies have been confined to obtaining fundamental knowledge of the characteristics of the vibrations themselves, because it was evident at once that he problem was extremely complicated. It was felt that any attempt to predict the effect of a ground vibration on an' type of artificial structure would be useless until the complexities of building vibrations are better understood. As opportunity offered, teats wore made in various types of structures and the effects of vibrations from many different sources were measured. In one set of tests (5)4/, it was demonstrated that the behavior of a building as quite different if it was shaken by vibrations originating outside tae foundation walls than if the source of the vibrations was within the building; vibrations coming from the round outside seemed to shake the building as a single loosely-coupled structure, whereas mechanically induced vibrations within the house seemed to set floors and walls in motion as independent units, each of which communicated its own natural motion to the adjoining member, causing a very complicated movement that was impossible to interpret.

Jan 1, 1938

By Wesley T. Holmes

This report describes the first phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected slag compositions in the titania-alumina-silica-calcia-magnesia system. Both the melting-holding-quenching method and the hot-stage microscope method were used in the tests. Liquidus temperatures of slags studied ranged from 1,217° to 1,667° C. The lowest liquidus temperature of the slags occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. Liquidus temperatures were also lowered when Si02 was substituted for Ti02 plus Al2O3 when CaO and MgO levels were held constant. Improved methods for the measurement of liquidus temperatures on very small samples are described.

Jan 1, 1968

By R. B. Schluter

Drying and preheating (partial induration) the green, unfired iron ore pellets is a means of reducing the energy required to produce metallized pellets. The Bureau of Mines processed three magnetite and two hematite concentrates through the unit operations of pelletizing, preheating in air, and reduction to metal to determine the effects of preheating upon the properties of the metallized pellets. The pellets were prepared in a 16-inch-diameter laboratory balling drum. Preheating and metallization were carried out in an externally heated 4-inch-ID by 4-inch-long stainless steel drum using air for the preheating atmosphere and lignite char as a reductant. The results 'varied considerably: two of the magnetites spalled when preheated in air at temperatures of 900° C and above, and the third magnetite and the hematite flotation concentrate required complete induration at 1,300° C to produce satisfactory pellets. The earthy hematite ore yielded excellent pellets at all preheat temperatures.

Jan 1, 1972

By K. J. Bathe

The current version of the computer program ADINA/BM (Automatic Dynamic Incremental Nonlinear Analysis for the Bureau of Mines) for linear and nonlinear, static and dynamic finite element analysis of mine structures is described. The complete report is divided into four parts. In Part A the program solution capabilities, the finite element library, the logical construction of the program and storage allocations are discussed. In Part B the theory and numerical techniques used in the program are summarized. In Part C brief problem descriptions and solution results for some sample solutions that have been transmitted as data cases with the program are presented. In the last section of the report, Part D, the users? manual of the program is presented. Program ADINA/BM is a general effective tool for coal mine structural analysis. The program is an extension of the computer program NON SAP (which was developed under an earlier contract with the U.S. Bureau of Mines). The important additional capabilities of ADINA/BM are: (1) the occurrence of all elements is time dependent, (2) all elements can be used in geometric and material nonlinear analysis, (3) the truss element can be used in elastic-plastic analysis, (4) the three-dimensional element can be employed in orthotropic, elastic-plastic and cracking and crushing analysis, (5) the program executes an out-of-core solution and thus allows the analysis of very large and complex coal mine models, (6) the truss elements can be employed as 2-4 variable-number-nodes elements, (7) a rock material model has been implemented, (8) displacement constraint equations can be imposed in the solution, (9) more flexibility in specifying the incremental solution strategy and an acceleration procedure in the equilibrium iteration are available

Jan 1, 1978

By James Gibbs

In order to provide an initial approach to the deposits of oil shale, nahcolite, and dawsonite in the central area of the Piceance Creek Basin in northwestern Colorado, the U.S.B.M. and associated contractor personnel drilled and cased a 96-inch ID shaft to a depth of 2,371 feet. The shaft was constructed using "big hole" drilling techniques and succeeded in giving access to previously inaccessible deposits of the above minerals. This report documents the construction from its beginning in January 1977 to its completion in January 1978. Procedures used and problems encountered are discussed in derail.

Jan 1, 1978

This Bureau of Mines publication contains the texts of the four papers presented at the May 6-7, 1980, seminar on the role of overburden analysis in surface mining. Coverage includes the geologic distribution of pyrite and calcareous material and its relationship to overburden sampling, overburden sampling and analysis, use of soil-overburden data in mine planning and development, and minesoil classification.

Jan 1, 1981

By Thomas C. Denton

In 1965 Africa maintained its position as a region of the world essential to advanced non-Communist nations for supply of vital metals and minerals. The position stemmed from the fact that Africa produced in large quantity a number of key minerals of which either or both resources and production capacity elsewhere did not approach the needs of the free world. The Republic of South Africa alone contributed more than three quarters of the gold mined in the entire non-Communist world besides an estimated 60 percent of metals of the platinum group and the entire new supply of amosite asbestos, and Africa as a whole was nearly the non-Communist world's only source of gem and industrial diamond. Africa also accounted for 83 percent of non-Communist world cobalt production. Besides these massive contributions, Africa in 1965 provided 50 percent or more of the new supply from non-Communist countries of the following mineral commodities: Lithium minerals, corundum, manganese ore: and chromite, and over 20 percent of new supply from non-Communist countries of columbium-tantalum concentrates, antimony, beryl, vanadium, phosphate rock, and copper. Africa also accounted for 18 percent of the non-Communist world's output of uranium, 14 percent of its tin, 11 percent of its lead, 9 percent of its zinc, and 8.9 percent of its crude oil output. With respect to chromite, at yearend Africa's reserves of the mineral were far larger than those of all other non-Communist regions combined. This probably also held true for manganese ore. In the case of crude oil, the fact that Africa's share of non-Communist world output was 1.6 percentage points greater than in 1964 was significant, particularly inasmuch as the output rate was continuing to increase at yearend.

Jan 1, 1967

By S. P. Godby, S. P. Sharples

Wind-tunnel tests were carried out of the conditions under which nuisance dust particles (100-1 000 micrometres) become entrained by wind. A laser entrainment monitoring system (LEMS) was used, and was found to provide an accurate means of assessing nuisance dust emissions from a surface. Accurate determination of the threshold entrainment velocity of dusts using the LEMS gives a baseline against which the performance of dust control techniques can be evaluated. Minerals tested included coal, petroleum coke, limestone, sand and pulverised fuel ash. Pilot field trials of a portable wind tunnel equipped with the LEMS have been successfully completed, providing a means of validating laboratory results in the field

Jun 19, 1905

Gangue-cemented paste backfill (GCPB), is a well-established green mining technology and significantly improves the recovery rate of mineral resources, prevents mine dynamic disasters, reduces surface subsidence, and consumes a considerable amount of solid waste. The addition of an early strength agent as an additive in cement-based materials provides several security, technical, and economic advantages. In this study, the early strength agent on the early age (3, 7 and 28 days) strength of GCPB is evaluated experimentally. The GCPB specimens have an initial sodium sulfate early strength agent concentration of 0%, 1%, 2%, 3%, and 4%, and the obtained samples were analyzed by testing for uniaxial compressive strength (UCS) and scanning electron microscopy (SEM). The test results show that the UCS of the GCPB specimens with sodium sulfate is much higher than that of the blank specimens. When cured for 3 days and 7 days, the strength of GCPB with 2% sodium sulfate increased the most, by 131% and 116% respectively. When cured for 28 days, the strength of GCPB with 1% sodium sulfate increased by 135%. Scanning electron microscopy (SEM) results showed that the GCPB with 1% and 2% sodium sulfate had better internal structure compactness, thicker acicular crystals, and more flocs. As a kind of early strength agent, sodium sulfate can react with calcium hydroxide to generate calcium dihydrate sulfate and then react with calcium aluminate; the hydration product (C3A) quickly generates calcium sulfoaluminate hydrate (AFt) needle-shaped crystals, forming an early skeleton and improving the early strength.

Jan 7, 2020

By Marshal Scherba

Coal seams approximately 7 feet, 9 feet and 20 feet thick at depths of 250, 600 and 1,000 feet respectively were detected using high resolution seismic reflection techniques. Investigation of seismic profiles indicates that good data are required to delineate faulting with only 20 feet of throw but that faulting with 50 feet of vertical displacement can be detected with poor data. Data acquired from dynamite charges fired in water saturated media were clearly superior to that acquired using charges dry tamped in 10 and 20 foot holes.

Jan 1, 1977

By L. D. Johnson

On a project which is to develop a system to suppress coal dust explosions, a facility has been built and several devices tested. The facility is a 317-foot, 4.5-foot diameter shock tube and to date 53 tests have been carried out with methane-air and methane/coal dust-air as the explosive mixtures. Suppression of slowly propagating (up to 300 ft/sec) flame fronts has been successfully carried out on two tests using the dry chemical extinguishing agent Purple K. Delivery of the material directly into the flame front Seems to be required if effective suppression is to be accomplished.

Jan 1, 1972

By J Zhou, L Crompton, K P. Galvin, J L. Sutherland, C P. Lowes, C Bezuidenhout, J Bijzet

Platinum Group Metal (PGM) bearing ores from the Upper Group 2 (UG2) reef often contain significant concentrations of chromite which can potentially be upgraded to produce a saleable product. A common approach is to implement gravity separation on the PGM flotation circuit tailings. However, where the particle size range of interest is broad and the lower size limit ultra-fine, the challenge is how to maximise the recovery at a saleable product grade without compromising throughput. This study was concerned with the performance of a REFLUX™ Classifier for beneficiation of a PGM bearing chromite ore and the benefits of size classification. The sample had a nominal top size of 0.5 mm and was processed over the complete size range and in two discrete size classes following classification at 106 µm. The primary goal was to produce a concentrate exceeding 40 wt. per cent Cr2O3, ideally approaching 42 wt. per cent Cr2O3, with minimal PGM losses above 106 µm. A major challenge was to process at the required solids throughput in a single stage with the feed pulp density constrained to a nominal upper limit of 30 wt. per cent solids. It was found that varying the controller density set point of the REFLUX™ Classifier produced strong control of the product grade. Products as high as 41.1 wt. per cent Cr2O3 were produced at 78.6 per cent recovery for the +106 µm material, while in the −106 µm portion the product grade was as high as 41.4 wt. per cent Cr2O3 at 83.2 per cent recovery. Processing the feed in discrete size classes enabled the volumetric feed and fluidisation rates to be optimised for a given application; hence, superior performance was achieved at the finer sizes. This work has demonstrated the value in considering feed preparation as well as technology selection in developing a robust process solution.

Aug 24, 2022

By Gary L. Stecklein

This final report delineates the findings of the test programs, simulations, and analyses performed to determine the requirements for the effective application of berms and guardrails as truck restraint systems for elevated mine roadways. Included arts criterion for effective vehicle restraint for guardrail applications and recommendations for berm applications based on scale model tests and computer simulations. Full scale haulage vehicle-berm interaction field tests were performed to correlate the results of these model tests and computer simulations. Recommendations for the construction of berms were made on the basis of tests of berm bearing strength, response of the vehicle to different berms, and predictions based on the obtained correlation

Jan 1, 1981

By Qing Wang, H. Sevim

Belt network simulators are the most widely used models in the design of belt networks. The simulators developed in the past two decades are reviewed and their limitations are discussed. To overcome these limitations and to provide a design model that can be used efficiently in real-life applications, a comprehensive non-simulation model has been developed. The features of this model are briefly discussed. A real example is used to demonstrate the model's superiority over belt simulators

Sep 1, 1991

By C. S. Tout

While investigating methods for determining the best temperatures for hot-working experimental stainless steels, the Bureau of Mines Albany Metallurgy Research Center developed a machine in which hot-twist tests could be made in a few minutes. This machine is similar to some used previously except that specimens are heated by induction instead of by radiation, and their temperature is measured by a calibrated radiation-detection unit instead of by a thermocouple. In. developing the technique for using the new machine, tests were made on specimens of medium-carbon steel, mild steel, and AISI (American Iron and Steel Institute) type 304 stainless steel. Tests also were made on as-cast specimens and preworked specimens of experimental AISI type 202, low austenitic stainless steel, and as-cast specimens of AISI type 301 experimental stainless steel. The optimum hot-working temperatures were determined for all types of steel tested. Also, data were gathered on the effects of test speed and temperature on torsional strength and the effect of twisting on tensile stress in the specimen.

Jan 1, 1962

By J. -M. Lopez-Cuesta, C. Petter, B. Otazaghine, M. Batistella, R. Sonnier

"Kaolinite is a dioctahedral aluminosilicate widely used as paper filler and coating pigment. At the best of our knowledge, kaolinite is not widely used in polymer industry. Therefore, in this study, the flame retardant effect of kaolinite in ethylene vinyl acetate copolymer (EVA) and polypropylene (PP) were studied and compared with an alumina trihydrate (ATH) and Talc. Cone calorimeter results shows that the weight percentage of ATH in EVA/ATH composites must be at least 50 wt. % in order to reach an improvement in fire retardancy in terms of pHRR. In the case of EVA/kaolinite, even with 35 wt. % the pHRR is largely reduced. Comparing PP/Talc and PP/kaolinite composites at 30 wt. %, both fillers leads to same reduction in pHRR with a slightly better performance for PP/kaolinite composites. In both cases an intumescent behavior of kaolinite composites was observed that could slow the rate of the rising degradation products, allowing radical recombination reactions. Also, it was observed that kaolinite forms a protective layer on the surface of the samples, which could insulate the material. These behaviors (intumescence and formation of a protective barrier) could reduce the transfer of the degradation products to the flame and explain the better performance of kaolinite composites. INTRODUCTION The use of mineral fillers as fire retardants in polymer matrix are well known and widely studied [1]–[10]. Aluminum and magnesium hydroxides (respectively ATH and MDH) are the most widely used inorganic fire retardants. To achieve fire retardancy with these mineral fillers, about 50-60% loading is required which decrease the physical properties of the composites. The fire behavior of composite EVA has been the subject of many studies [4], [7], [9]–[15]. EVA copolymers are commonly used in the cable industry, due to their high ductility, even at high loading rates. In such applications, the flame retardant systems should be introduced into the polymer to improve the fire reaction. Many flame retardant systems have been tested but the most used industrially relates to formulations based on hydrated mineral fillers (aluminum hydroxide and magnesium hydroxide). Their low cost and reduced fumes generation explains their success. However, to obtain good performance with this type of flame retardants, it is necessary to incorporate high levels (up to 65 wt %), which severely impact other properties such as processability and mechanical behavior. The main modes of action of these flame retardants are the dilution of the gas phase, the endothermic decomposition and a barrier effect created by the inorganic oxide residue which may be improved by the incorporation of other components such as montmorillonites, silicas or talcs."

Jan 1, 2015

In July 1982 the Committee on Underground Coal Mine Safety completed its study of safety in U.S. underground coal mines; the results of the study were published in the National Research Council report entitled Toward Safer Underground Coal Mines. One of the findings of this study was: THERE IS A STRONG CORRELATION BETWEEN MINE SIZE AND FATAL INJURIES. THE FATALITY RATE IN MINES WITH 50 OR FEWER EMPLOYEES IS NEARLY THREE TIMES THAT OF LARGE MINES (WITH OVER 250 EMPLOYEES), AND ABOUT TWICE THAT OF INTERMEDIATE-SIZED MINES (WITH 51-250 EMPLOYEES). Although the Committee explored possible reasons for the higher fatality rate in the smaller mines, it was not able to explain this phenomenon fully. Therefore the Bureau of mines requested that the Committee undertake a supplementary study of fatalities in small underground coal mines. The Committee met in the fall of 1982, discussed the problem, developed an approach to it, approved a program of statistical analyses, and authorized a panel of four committee members to explore the problem in greater depth. The panel, in turn, reviewed the results of the statistical analyses and met with the president of the National Independent Coal Operators Association and with several owners of small underground coal mines for a detailed discussion of the unique problems of small mines. Panel members examined 66 individual fatality reports prepared by Mine Safety and Health Administration (MSHA) inspectors who investigated fatal accidents that occurred in small underground coal mines in 1979 and 1980. This report is the result of those studies, analyses, and deliberations. The first draft was prepared by the panel, but the report has been reviewed and approved by the entire Committee.

Jan 1, 2011

By F. C. Foshag, P. E. Wingrove

The Kayford, Boone and Nicholas Division of Bethlehem Mines Corp. operates a modern coal preparation plant in Van, WV. Since start-up of the Van plant in 1976 until the summer of 1980, the refuse handling system proved to be a costly maintenance problem and a material handling bottleneck. During the 1980 two-week miners' vacation, the original system - which included two screw conveyors and a drag conveyor - was replaced by an installation using two Flexowall steep angle belt conveyors. This paper describes the technical and economic analysis that led to the new installation and reviews its first year operating performance.

Jan 1, 1983