Search Documents

By Robert W. McKibbin

The Bureau of Mines conducted laboratory tests to determine the slurry transport and deposition properties of coal waste. A 188.5-ft pipe test loop was constructed with instruments to measure density, flow, and power and discharge, suction, and differential pressures. A 20-ton ample of Western coal waste was crushed and screened to 100 pct minus 1/2 in. Eight loop tests using this graded waste were run at slurry densities ranging from 1.15 (25 wt-pct solids) to 1.46 (60 wt-pct sol-ids) 0 The resultant friction-'pressure gradients ranged from 0,06 to 0.24 ft of water per foot of 4-in standard steel pipe. Particle-size degradation was significant.. In a typical loop test lasting 25 min, the minus 200-mesh fraction increased from 19 pct to 34 pct. Deposition tests showed that without the use of a flocculant, the slurries would not dewater when left to stand for 1 week. With flocculant, additional water was releas2d; however, the settled slurries remained thixotropic. Further testing is necessary to determine their suitability for use as backfill material in active mines.

Jan 1, 1983

By M P. Cipold, J F. Bachmann, C C. Bachmann, J Ha, H B. Wurst

In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink–?float analysis. Using traditional sink–float method it is not possible to sample and automatically measure. This fact, as well as time, cost and safety aspects, as well as required and manageable sample size of the sink–float method have prompted the search for a new approach for establishing separation performance criteria. This is especially important as performance levels of separator plants can be maximised if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes available in time. The new method to establish washability and associated performance information utilises at least two measurement technologies concurrently: single energy X-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy X-ray transmission and image processing.If used as a standard laboratory device the continuous build-up of the washability curve allows to evaluate the statistical significance of the sample size during measurement.The measuring method can even be improved if it is combined with an automatic sampling system that feeds a continuous and representative particle stream to the analyser. Then the value of the collected data increases considerably since the washability data are additionally available in time to be considered in the control of the process plant. The washability curve can be derived and is continuously updated based on the particles measured during the past time interval. Older curves and results are stored in a database and can be retrieved for later reference. This technology now enables automated sampling and integrated automated measurement, which was previously not possible.This incorporation of an automated washability monitor at a representative sample gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested using a range of samples with different densities, varying from 1 g/cm3 (coal) to 5 g/cm3 (iron ore).CITATION:Bachmann, C C, Bachmann, J F, Cipold, M P, Wurst, H B and Ha, J, 2017. Inline analysis of washability parameters for process control, in Proceedings Eighth World Conference on Sampling and Blending , pp 213–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Sengpasith Houngaloune

Arsenic, which is a toxic and carcinogenic element, causes serious environmental problems throughout the world. It is also known as a major contaminant in the non-ferrous mining and extractive metallurgical industries, thus its disposal is one of the most important environmental issues for the mining and metallurgical industries. In order to ensure a safe disposal environment for the final wastes, stabilization of arsenic has been studied extensively with various approaches. Solidification/stabilization (S/S) represents one of the most effective methods to reduce the availability of arsenic in soil and waste by transforming toxic or potentially hazardous phases into less hazardous ones. Cement based S/S processes could reduce the solubility of arsenic in solid waste, using inorganic binders such as cement, lime, and pozzolanic materials. A new tailings management technique, called cemented paste backfill (CPB), has become widely employed for improving mining techniques and for tailing storage purpose and this technique could also enhance arsenic stabilization, by fixing the contaminants in the binder matrix. Disposal of arsenic in the form of scorodite (FeAsO4?2H2O) has been widely accepted as currently the most suitable method for stabilization and the safest known storage material. The Bio-scorodite process has been reported to be more economic and environmentally friendly method than the chemical crystallization processes. Retention of arsenic by schwertmannite (Fe8O8(OH)6SO4), a metastable ferric oxyhydroxy sulfate mineral, has gained more attention in the recent years. Schwertmannite has a large specific surface area and high capacity to adsorb arsenic in solution. Several researchers have reported that the transformation of schwertmannite to goethite could be retarded by the presence of adsorbed arsenic; therefore schwertmannite might be viable alternative for long-term storage of arsenic. In this paper, various approaches used in arsenic stabilization are reviewed with emphasis on the development in the recent years.

Aug 1, 2013

By D. G. Krige

For the purpose of determining confidence limits for ore grade estimates, an extensive simulated data base was used, which included 1728 ore blocks with ‘actual’ grades and the corresponding estimates based on ordinary and simple kriging. The practical results show that conditional unbiasedness is essential and that acceptable confidence limits can then be set using Normal theory for the simulated error distribution based on the logarithms of the ratios of ‘actuals’/estimates with a variance related to the kriging variance. The mean of the data used to prepare the variogram and the estimated block grade are to be used properly in this approach. A practical analysis was also done of the actual point and block data from a very large mined out Carbon Leader area. The distributions of the actual grades for two levels of block sizes with different levels of variability were fitted using three models, ie. 2-. 3- and compound-lognormal. The trends of tonnages, grades and relative profits for a range of pay limits, as well as the usual tonnage-grade curves, show a practical insensitivity for the choice between the three lognormal models considered.

Jan 1, 2003

By W. P. Yant, R. R. Sayers, H. W. Shoaf, John Chornyak

"The contemplated use of dichloro-difluoro methane in domestic and commercial refrigerating appliances and in air-conditioning equipment for Public buildings and possibly homes, brings attention to the health hazards involved in a wide potential exposure of the public to vapors of another new product, and for the first time to vapors of an organic fluorine compound. The objective in the development of this new refrigerant, however, has been the mitigation of health and explosion hazards in automatic refrigeration, and accordingly these factors have been given primary attention. Early in the development, the Bureau of Mines was requested to make a laboratory study of the toxicity and potential hazard:"" and it was on the basis of the results of this work and the results of a preliminary investigation made in another laboratory5 that the compound has been selected for commercial use. Although the investigation conducted by the Bureau of Mines is still in progress, information has been obtained to indicate the order of the toxicity and the magnitude of the health hazards involved in the use of dichloro-difluoro methane as a refrigerant. The following is a summarized report of the work completed to date:Additionally work rich is in progress at the present time includes a determination of the lethal time-concentration curve for animals and a study of the response of persons within the range of safe concentrations.The writers desire to jive acknowledgment to T E. Midgley, Frigidaire Corporation, Layton, Ohio, for suggesting the investigation, for arranging for the cooperation of the Frigidaire Corporation, and for advice during the experimental work; to Robert A. Kehoe, The Eichberg Laboratory of Physiology, University of Cincinnati, Cincinnati, Ohio; and E. R. Hayhurst, college of Medicine, Ohio State University, for consultation and advice in planning the work; and to the following employees of the Bureau of Mines for assistance in performing the experimental work: L. M. Berger, chief scientific aid, S. J. Pearce, junior chemist, and Ethel B. Stead, technician."

May 1, 1930

By Laxman S. Sundae

A Bureau of Mines investigation was conducted to determine the effect of specimen volume on the apparent tensile strength of disks of St. Cloud Gray Granodiorite, Lithonia granite, and Rockville granite. The investigation used a technique developed by the Bureau to determine apparent tensile strength. Because the test specimens were selected without macroscopic defects, that is, cracks, joints, and planes of weakness, the strength variations are solely due to microscopic features. Several replications of each test were performed. Data for each set of specimens were fitted to a power law of the form y = axb, where y = apparent tensile strength, x = specimen volume, and a and b are constants. This power law is essentially a form of Weibull's theory. The average coefficients of correlation for St. Cloud Gray Granodiorite, Lithonia granite, and Rockville granite were 0.85, 0.53, and 0.78, respecitvely. In all cases a decrease in strength with increasing volume was noted; in the extreme case, a decrease of 40 pct was noted with an elevenfold increase in volume. The decrease in strength with increasing specimen volume is explained in terms of Weibull's theory.

Jan 1, 1974

By Mark A. Williams, James D. Humphrey

Without question, draglines are one if not the most effective tools available to the surface mining industry for overburden handling. With few moving parts and a two- or threeman crew, this machine silently sits and chews into millions of yards of overburden annually. A 100 cubic yard machine operating for 30 years will excavate three-quarters of a billion yards of material during that time. That is 750,000,OOO yards of material!

Jan 1, 1990

By Bruno Leonardy Sousa Lopes

Este trabalho tem como objetivo mostrar a correlação entre as fases constituintes do aço superdúplex SAF 2507 na junta soldada por processo MIG-MAG, considerando os efeitos da energia de soldagem nas propriedades mecânicas e de corrosão. Os resultados mostraram que a energia de soldagem causou mudanças no balanço das fases a/?, na formação pontual da fase s nos contornos de grãos ferriticos e mudanças de microdureza e tenacidade nas regiões da zona fundida (ZF) e zona termicamente afetada (ZTA), além de promover o aumento da fase ? e do índice de resistência à corrosão por pite (PREN?), quanto maior energia de soldagem. Entretanto, a tenacidade na ZF diminuiu mesmo com maior formação da fase ?, coalescimento dos grãos ferriticos, elevando a microdureza na ZTA sob baixa energia de soldagem. Assim, espera-se que estes resultados permitam estabelecer diretrizes para procedimentos de reparo em aços superdúplex sob processo de soldagem

Aug 17, 2017

By D Reddy

Rosh Pinah Zinc Corporation is a zinc-lead mine located in southern of Namibia. It is currently considering the development of a low grade ore body containing about 2.8% zinc. This ore can be utilised by the concentrator if it could be upgraded prior to the ball mill. Preliminary work indicated that the ore may be upgraded in a pre-beneficiating stage by using dense medium separation, X-ray sorting or a combination thereof to a feed grade of minimum 9% zinc. This paper describes the process followed in evaluating the technologies for pre-beneficiation. The results from test work indicated that the low grade ore is amenable to pre-beneficiation by both dense medium separation and X-ray sorting. A comparison between the two technologies showed that dense medium separation marginally outperformed X-ray sorting on grade and recovery. The results for the X-ray sorting were achieved by tuning the calibration curve specifically for the samples tested.

Jan 1, 2008

By Pavel Vasak

Microseismic monitoring has become standard practice in the mining industry as a ground control monitoring tool at depth. Translating the information into practical hazard assessment tools for the rock mechanics practitioner is the focus of research jointly conducted at Creighton Mine by INCO Mines Technology Centre (MTC) and the Geomechanics Research Centre (GRC) in Sudbury, Ontario. Rock mass damage mechanisms are typically related to stress and the presence of geological structures. Due to well executed de-stress blasting practices at the mine, stress related problems are minimized. However, structurally related damage mechanisms associated with shear zones, faults and joints pose a substantial hazard. Identifying active structures from the dataset of seismic and microseismic events is generally problematic. We propose a new methodology that uses a combination of spacetime event density, hierarchical clustering and principal component analysis to identify planes of microseismic activity, termed active planes (APs). Once identified, the presence and intersection of active planes can be used to provide a hazard ranking for nearby excavations. The ranking is based on the standard Q rock mass classification system, with emphasis on the joint set number (Jn) and stress reduction factor (SRF) parameters. If the rock is treated as a fractured continuum, then, the Jn indicates the degree of freedom for blocks to move and hence, increased potential hazard. An increased hazard can also result if the APs are larger-scale and discrete (faults) rather than ubiquitous (joints). In this case the SRF is used as a measure of the degree of looseness in the rock mass.

May 1, 2004

By Yotamu Hara, Animesh Jha

"High Curie temperature and large magnetic anisotropy make cobalt an important magnetic material for power engineering applications of magnets operating above ambient. It is also an essential constituent of modem lithium - cobalt oxide batteries, without which modem electronic gadgets will be functionless. Both these applications of cobalt save energy and reduce C02 emission. Ironically, however the production of cobalt from copper and nickel smelting in the world remains one of the least energy efficient process. The paper analyzes the energy balance, material and process chemistry of overall cobalt recovery and the waste generated, which entail the process limitations. We discuss a novel approach for the reduction of sulphide minerals with CaS04, permitting better separation of metals from slag and generating higher concentrations of S02. Such an approach may seem to be an alternative energy efficient option for processing and further purification of cobalt in metallic form. The results are discussed in the context of process thermodynamics and reaction kinetics for Coalloy production.IntroductionCopper sulphides bearing minerals are predominantly associated with iron and cobalt sulphides minerals. Carrollite (CuC02S4) is a mineral that has both copper and cobalt sulphides [1,2], which may also contain FeS, by substituting either Cu2+ or Co2+ ions in mineral lattice. On smelting copper - cobalt - iron sulphide concentrates, some parts of the cobalt often partition to matte at preferentially low oxygen potential by forming eventually an alloy phase with copper, however a significant fraction is often lost into an oxide slag rich in iron and silica. The slag heaps accumulated in the Copperbelt region in Zambia from last 60 years of mineral processing and metal extraction is reported to be 0.3 to 2.6 wt% of cobalt element, which is high [3]. Cobalt is also available in smaller concentrations in the copper smelting and converter slag, as reported in the investigations on the recycling of such slag materials using leaching with ammonium salt [4], iron chloride [5], and sulphuric acid [6], and solvent extraction [7].The recovery of cobalt from slag, irrespective of the techniques researched so far, does not seem energy efficient because the molten slag at 1300°C is quenched by losing thermal and chemical energy. The quenched slag is again reheated to above room temperature for leaching and above liquidus for carbothermic reduction of residual cobalt oxide. For example, in Mintek DC arc smelting [3], 80% of cobalt and 95% nickel are recovered by expending 600 kW per tonne. Assuming that the mineral carrollite is the starting phase, the univariant calculations for the Co-Ca-Si-S-0, Fe-Ca-Si-S-0, and Co-C-Si-S-0 systems are shown in Figure la, lb, and le, respectively at 1573 K."

Jan 1, 2012

By Edward M. Kawenski

Float dust deposits in return airways in bituminous coal and lignite mines present a special explosion hazard. Research is in progress at the Bureau of Mines experimental coal mine to evaluate the degree of the hazard and to develop measures for preventing dissemination of dust into the ventilating air current. To determine the extent of this hazard prevailing in operating coal mines, 711 dust samples were collected in 50 mines located in the major coal fields of the United States. The mean quantity of coal and the incombustible content of the dust in the samples were determined. The term "float dust" is used to designate particles smaller than 74 microns in diameter (particles passing a No. 200 sieve) which have settled from the air current. Dust usually found in roadways and in working places is coarser than float dust, and is termed "coarse dust" (particles passing a No. 20 sieve). Variations in amount and incombustible content of coarse dust in a midwestern mine were studied previously.5

Jan 1, 1963

By O. F. Brown

The use of quality materials (aggregates and asphalt binder) in optimal proportions is the key to producing optimally performing hot mix asphalt (HMA). The Superpave mix design standard in the US introduced specific volumetric and binder property requirements in HMA design. Different methods for HMA constituent proportioning have been proposed in various guidelines. The design process to determine the HMA blend is currently iterative and engineers rely almost exclusively on experience. This approach is time consuming and often does not result in cost-optimal HMA mixtures. This paper introduces a mixed integer linear programming (MILP) optimization model for hot-mix asphalt constituent proportioning. The MILP model minimizes the total mix cost while satisfying all the volumetric, binder and mix property specification requirements. The model has been successfully validated with real-life example. The aggregates and binder ratios from the model were in close agreement with those from the contractor. The Bailey ratios and the gradation constraints were also satisfied. The cost of the optimal mix was $0.804/Mg less than that of the contractors?. This marginal reduction might make all the difference in an industry that is highly competitive. The MILP model also demonstrated that adding RAP to the contractor?s design would reduce the cost of the blend by $5.74/Mg. The virgin binder content was reduced by 1% because of the recycled asphalt contained in the RAP. This work represents the first successful attempt in incorporating both aggregate and asphalt performance requirements into the optimization formulation. Applying these models will ensure the minimum cost mix that meets all constraints and will increase profit margins for plant operators.

Jan 1, 2012

By Zach Ahinga, Mike McRae, Dave Hopkins, Steve Klein

The San Vicente Pipeline project involves the construction of an 8-1/2 foot diameter water pipeline in an 11 mile long tunnel in San Diego, California. The tunnel will be excavated in extremely variable geologic conditions consisting of strong granitic and metamorphic rocks, weak sedimentary rocks, abrasive conglomerates, and mixed face conditions. This paper discusses the challenging geologic conditions and some of the key design evaluations for the project. Currently design work for the project has been completed and construction will be underway by mid-2005.

Jan 1, 2005

By X. Shi

This paper presents design and implementation details of a fuzzy-behavior-based controller for an automated excavator. The robotic excavator is equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered during the excavation process from bucket-mounted force sensors. Implementation details card experimental results using the fuzzy-behavior-based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining-excavator controller.

Jan 1, 1997

By N September, R Abate

Bateman Modular (previously Van Eck and Lurie) has been building and supplying the mining industry with modular DMS plants for the last 30 years. These DMS modules range in capacity from 1 tph to 200 tph. The most popular unit produced by Bateman Modular over the years has been the 50 tph module. Development In the last 7 years a need has arisen from the industry to provide Modular DMS plants that can treat higher tonnages (150 to 200 tph). The first DMS provided to the mining industry based on the modular concept was a 150 tph DMS Module to MIBA in the DRC. Since then Bateman Modular has provided some 14 Mega DMS modules over the last 7 years with the latest two orders from Debswana (Damtshaa double up project) and Namdeb. Ever since the first Mega Module was supplied Bateman Modular has been improving the Modules. Implementation The modules can be supplied in different configurations so as to improve the overall availability of the plant. Two off 150 tph DMS modules were supplied for a Transhex operation. This allowed the client to still operate one DMS module while maintenance is being performed on the other DMS module. The client also has the option of choosing a single module. Successes The following list of projects provides the base for the success of the Mega Modules.

Jan 1, 2006

By Steve Dillingham

Here in the United States, as well as around the world, pose a daily dilemma - to wash or not to wash. Let’s face it, all trucks, especially our industry work horses - bulk trucks - get dirty. We all know that these units can be very expensive and washing them keeps your business investment looking new, improves public relations, fuels company pride, and facilitates equipment safety and preventative maintenance inspections.

Jan 1, 2001

By R. N. Pryor, S. H. Shaw, D. L. Dowie, S. H. U. Bowie, M. J. Cahalan, S. F. Gandar

It is concluded that land-based mineral resources will be adequate for most minerals in the immediate future, but in the long term more minerals will come from offshore locations. Because the oceans are international and can transport pollution, international control of offshore workings will be necessary. In the UK and similarly highly developed areas, the working of low-value bulk minerals will create increasing problems in urban development and countryside preservation. Much more information should be published on standards to be adopted and their costs, if emotional social pressures founded on ignorance are to be avoided. The Town and Country Planning Acts have greatly improved the environmental quality in Britain in relation to mineral working. In the long term conservation of some minerals in short supply may be necessary on a national or international basis. Much research is required for the determination of adequate criteria and standards for the preservation of environmental quality in the mineral industry. New local, national and international legislation will be required and the adoption of voluntary standards by trade associations should be encouraged wherever appropriate

Dec 1, 1971

By George M. Fowler, J. P. LYDEN

T HE relationship of geological structure to orebodies and to the great masses of chert in the Tri-State mining district is of such significance that it prompts a brief recital of the existing information regarding the various periods of structural deformation. We began to note a relationship between structure and orebodies early in our studies of the field, and further work revealed a like relationship of structure to the great masses of chert so commonly associated with the ore-

Jan 1, 1934

By Caciola Jr. Joseph J., Nidal M. AbiSaab

"Thanks in great part to the geology of the New York City Metropolitan area, mini-caissons are a popular choice for deep foundations. These drilled elements are readily available, easy to install with minimal impact on adjacent structures, and can be designed with large compressive and tensile capacities. Despite the frequency with which they are employed, the engineering design community is divided over several of the underlying principles governing the design of mini-caissons. This paper seeks to draw attention to several of these issues in an effort to encourage further research and discussion, namely: (1) how the allowable stresses have changed for the NYC Building Code over time, (2) the inconsistent load transfer mechanisms considered for geotechnical capacity, and (3) the role of the permanent steel casing towards structural capacities of mini-caissons.INTRODUCTIONIn the local construction nomenclature, mini-caissons are drilled deep foundation elements which derive their capacity from a socket in rock. A permanent steel casing (commonly between 7- and 24-inches in diameter) aides the drilling through overburden soils to the top of bedrock. Afterwards, an uncased rock socket is drilled into the bedrock and the inside of the casing and rock socket is inspected by means of portable video equipment. After inspection, the interior of the socket and casing is filled with steel reinforcement and concrete or grout. The casing-soil interface is generally ignored for axial design purposes and the full geotechnical compressive or tensile capacity is assumed to be generated in the rock socket. Figure 1 shows a typical mini-caisson cross section.Mini-caissons have been used for decades in the New York City area for a number of reasons. They have historically been proven to develop high axial capacities in the city’s metamorphic rock (Tamaro et. al. 2000), often exceeding 300- to 500-tons. Additionally, their method of installation (drilling) is generally able to bypass layers of dense Glacial Till, boulders, and manmade fill which would interfere with the installation of other pile types (e.g. driven piles, auger cast piles). Further they are able to extend to depths exceeding 50-ft to reach bedrock underlying a site, making them a useful tool in areas where rock is relatively deep or varied in elevation. Drilled casing installation also results in fewer vibrations and disturbances to adjacent structures and can occur in areas of restricted access (a constant concern for any project in a dense urban environment such as NYC)."

Jan 1, 2016