Search Documents

By Arístides Sotomayor

El presente texto señala la importancia del oro a nivel financiero y minero ya que los inversionistas suelen utilizar este metal para obtener ganancias debido al mínimo riesgo existente en la pérdida de su valor comparado con otras divisas. Así, se estima que en el Perú, existen 480 unidades mineras de oro, de las cuales 28 concentran cerca del 90% de la producción nacional, como la Minera Yanacocha, Minera Barrick, Compañía de Minas Buenaventura, Consorcio Minero Horizonte, Aruntani y Aurífera Retamas. Entre las dos regiones que producen mayor cantidad de oro está: Cajamarca y La Libertad ( 38%) y la tercera región es Arequipa, seguida por Madre de Dios (9%).

May 1, 2016

The evident need to improve the reliability of fluid power systems in underground coal mining equipment prompted the U.S. Bureau of Mines, and later the Department of Energy, to contract with the Fluid Power Research Center at Oklahoma State University for a research project to develop methods for achieving this end. Since the work of the contract was completed at about the time DOE was relinquishing its underground coal mining projects to BOM it was decided to issue the final report under 80M cover. The contract revealed that the major causes of poor reliability were: (1) poor overall system design, (2) poor component contamination toleranace, (3) poor system filtration, and 4) poor maintenance practices stemming from a lack of defined maintenance procedures and enforcement of same. This report demonstrates the variability of the reliabilities of components of similar performance description when subjected to standard tests. Improved design procedures are recommended and the information needed to specify and select components whose reliability is predictable and optimum without sacrifice in performance or significant increase in envelope size.

Jan 1, 1983

By J. S. Vanderploeg

I WILL begin this presentation by citing the annual per capita use of copper in Canada. This is best calculated by taking refinery domestic sales, plus imports of the products of foreign fabricating mills (very little refinery copper is imported), and deducting the exports of Canadian mills. No attempt has been made to estimate the copper content of imports or exports of machinery, motors, etc., but the trade balance here is probably against Canada. In any event, we find that, though varying somewhat since the war, the estimated yearly per capita figure has reached a high of 18 pounds. This is practically on a par with the United States. The rest of the world uses an average of about 2 pounds per capita, yearly, though this includes some countries, such as Sweden, Germany and England, which consume much better than average quantities. It looks, therefore, as if the Canadian copper industry has not (as has been generally charged) been asleep after all.

Jan 1, 1962

By Joseph Kuti

Longwall mining is the term used for the underground extraction of a wide and deep panel of coal. Such a panel may be blocked out by one or more entries on either side ("head" and "tail") of a longwall face. If all the entries are pre-driven, the panel extraction is termed longwall retreat mining. With one exception, all the longwall faces in the United States are of this type. (1) prior to the general decline in the rates of production with Continuous Miners, the development of the multiple entries generally kept ahead of the longwall extraction rate. This is no longer the case: longwall extraction rates far exceed the rate of development. In addition to this problem, in newly established mines, the development of a haulage and bleeder system based on multiple entries results in a lead-time of three years or more before longwall mining can be applied. This is one reason why earlier projections and much of the optimism attached to longwall mining as a principal "savior" in the energy crisis should be viewed with some caution.

Jan 1, 1978

By Donald M. Liddell

ALTHOUGH the midday lunches of business associations have been re-echoing the phrases that re- search would lead us out of the depression and that the last place to economize is on research, nevertheless most executives apparently concluded that it was their neighbor who ought not to economize in research, and that in their own plants what had been discovered in 1929-30 was sufficient to lead them out of the wilderness. At any rate, I have discovered much less that seems worth noting, and compared with 1931, the report volume of the committee members is off about 40 per cent, and compared with 1929, about 80 per cent. Evidently there is some hookup with the +tee1 industry as to output, and the Report Reading Committee should investigate this and the relative use of commas and periods.

Jan 1, 1933

By J. N. Van der Merwe, D. P. Roberts

The two components of pillar design formula being used in South Africa are pillar strength and pillar load. While considerable effort has been directed to the determination of pillar strength, the other half of the safety factor equation, the load, has not received the same amount of attention. The load acting on pillars has always been calculated using the Tributary Area Theory (TAT). This paper summarises the recent studies on coal pillar loading using various numerical models. It concludes that although there are meaningful differences under certain circumstances, there is still a compelling argument to use the TAT in coal pillar design. Les deux parties composantes de la formule de conception de pilier généralement utilisée en Afrique du Sud sont la résistance de pilier et la charge de pilier. Tandis que des efforts considérables on été dirigés vers la détermination de la résistance de pilier, l’autre moitié du facteur de sécurité n’a pas reçu la même attention. La charge agissant sur les piliers a toujours été calculée avec la Théorie d’Aire Tributaire (TAT). L’étude présente résume les études récentes sur la charge de pilier de charbon utilisant des modèles numériques variés. La conclusion est que bien qu’il y ait des différences significatives selon les circonstances, il y a toujours un argument puissant pour utiliser le TAT dans la conception de pilier de charbon. Die in Südafrika für die Auslegung von Pfeilern verwendeten zwei Formelkomponenten sind Pfeilerstärke und Pfeilerbelastung. Während beträchtlicher Aufwand zur Bestimmung der Pfeilerstärke gemacht wurde, wurde der anderen Hälfte der Sicherheitsfaktorsgleichung nicht die gleiche Aufmerksamkeit gewidmet. Die auf die Pfeiler wirkende Last wurde immer unter Verwendung der Tributary Area Theory (TAT) berechnet. Diese Arbeit fast neuere Studien betreffend der Belastung von Kohlepfeilern unter Verwendung verschiedener numerischer Modelle zusammen. Die Schlussfolderung ist, daß obwohl unter bestimmten Vorraussetzungen bedeutende Unterschiede existieren, nach wie vor ein bezwingendes Argument besteht TAT in der Kohlepfeilerauslegung zu verwenden.

Jan 1, 2003

By Francis J. Fratttali, Verda McLendon, Stanley J. Green

"INTRODUCTION During the first phases of the war emergency the shortage of aluminum prompoted the Bureau of Mines to investigate methods for using low-grade bauxites of high silica content and also clays as raw-material sources of this strategic metal. The Bayer process treats low-silica bauxites to provide the industry with a major portion of the purified alumina, which contains very low percentages of silica and other impurities. One of the methods investigated in the laboratories of the Bureau of Mines for low-grade materials is the lime-soda sinter process, which was studied on a pilot-plant scale. In this process, the alumina content of the alumina-bearing minerals Bs made water-soluble by sintering the raw material with limestone and soda. Simultaneously, the siliceous material is rendered insoluble. The sinter is extracted with an alkaline liquor, and the resulting extract liquor is treated as follows to recover the alumina: (1) Autoclaving with lime to remove silica as a zeolitic complex and (2) treatment with CO2 to precipitate alumina as the trihydrate (A1203.3H20). Figure 1 is schematic flow sheet of this process.As the process is cyclic, it is necessary that nearly all of the soda and alumina remaining in the plant liquors after carbonation be recovered. Upon passing through one cycle, these liquors contain 14 to 15 percent NaCO3 2 to 5 percent NaOH, 1 to 3 percent A1203, minor amounts of silica, and, with certain materials such as Pennsylvania diasporic clays, 0.5 to 1.0 percent Na2S04. Approximately 50 percent of the Na20 in these liquors must be returned, as soda ash, to the dry-grinding and raw-materials blending operations. Previous work (6)5/ on sulfate-free solutions demonstrated that two methods for recovering Na20 were feasible, namely: (1) Salting out Na2C03.H20 by evaporation of the carbonated solutions and (2) crystallizing Na2C03.10H20 by cooling the concentrated carbonated solutions."

Sep 1, 1947

By L Mottola

Three decades ago mining companies, principally in North America, aided by machine and explosive manufacturers, started significant attempts to develop and implement automated mining systems, mainly underground. These tended to be motivated by decreasing cost, increasing productivity, reducing labour requirements, and improving safety. These are important business drivers, however, little attention was given to the underlying goal of mining automation, namely to bring upstream processes in control and reducing variation, as seen in downstream mineral processing plants.This paper first reviews the nature of Lean Thinking and its application in the context of the growing commitments by industry to develop future automated mine production systems. The paper then makes reference to prior and current experiences in open pit blasthole drill and shovel performance monitoring, to demonstrate the principle that machine performance data offers as a means, not only to characterise the dynamic geological and working environment, but also to provide a foundation for automation. In this case, drill and shovel monitoring was originally motivated as a means to optimise blast fragmentation through more effective drill and blast designs that are based on an accurate determination of the bench geological and geotechnical characteristics, hence managing variation in the drilling and blasting process. This paper considers how automating and integrating such components of the mine production system would bring processes into a controlled state, creating value at the face, within a framework of Lean mining.

Nov 22, 2011

By Zhang Libo, Peng Jinhui, Zhang Zhengfu, Fu Mengbi, Han Yamei

In this paper, results of a novel synthesis method of carbon-coated LiNi113Mn113Co11302 cathode material for lithium-ion battery are reported. The carbon coating was produced from a precursor, glucose, by microwave-pyrolysis method. The structure, morphology and electrochemical performance of the bare and carbon-coated LiNi113Mn113Co11302 were characterized by X-ray diffraction, scanning electron microscopy and charge-discharge tests respectively. The L8(27) orthogonal experiments were carried out to optimize LiNi113Co113Mn1130z/C technological conditions. The conditions of the orthogonal experiments were that the glucose content were 1.5 % and 4 %, the holding time were 15min and 30min, the heating temperature were 400 °C and 500 °C and the solvent were H20 and CH3CH20H. The main experiment target include specific capacity at 0.1C and 0.2C, Capacity retention rate, medium voltage attenuation rate and The fifth discharge medium voltage. The data were analyzed by Minitab 14 statistics software. The results of analysis of variance indicated that the most influential factor was the glucose content despite of discharge rate. Secondly, the effect of the solvent was equivalent to the holding time.

Jan 1, 2013

By R. M. Santmyers

The pigments, whose colors are due primarily to iron exides and iron hydroxides, comprise a variety of yellow, brown, red, and sometimes black paint-coloring agents, both natural and artificially prepared. The natural pigments in this group include ocher, umber, sienna, mineral paints, paint rock, and mortar colors. When the natural color or tinting power--either in the raw state or after treatment--is too weak, these pigments may be "forti- fied" or strengthened. Ocher, umber, and sienna, rhile often described as "iron oxide pigments," are also known as "earthy" rigments. Inasmuch as the iron content of these pigments is, in general, somewhat lower than that of other iron oxide pigments, the ochers, umbers, siennes, and other brown earth pigments are not discussed in the present paper. In addition to a discussion of natural or artificial pigments whose color is due to the presence of iron oxide in some form, this paper contains data on mortar colors, which are medium or low grade pigments used for tinting mortar, cement, and concrete. A great variety of materials are used for theso purposes, including "blue billy" (residue left from roast- ing pyrite), ground slate and shale, and even culm from coal washeries. Dur- ing the past three years, there has been a definite trend among the producers of iron oxide pigments to push the sales of the better grades of colors for tinting mortars. Due to the amount of low-grade coloring matter that is re- quired to impart a strong color to concrete (in soro cases as high as 15 per cent of pigment is necessary) the strength of the cement may be materially impaired. The addition of some 2 per cent of the higher grades of iron oxide to the concrete mix imparts a brighter and stronger colcr, does not weaken the material, and in the end is not as expensive as the low-grade pigments formerly used. Iron oxide pigments occur in nature in various shades and colors, but the red pigments are the most important and account for the larger part of the total red pigments used.3/ The nomenclature of these red pigments is involved and the names given to them are descriptive of the shade rather than of origin, method of produc- tion or chemical composition. In most cases the red pigments under this class may occur naturally or may be produced by heating hydrous iron oxide pigments such as yellow ocher to a sufficiently high temperature to drive off the water of composition. They may also be prepared by fortifying naturally-occurring pigments with stronger natural or synthetic oxides or with coal-tar dyes (e.g. alizarine lake), Most of the mineral reds derive their color from the presence of ferric oxide (Fe2O3), the mineral hematite. This may be present in relatively small percentages, as in the red slates and shales, or it may constitute as much as 90 per cent or more of the material, as in Spanish red. The principal iron oxide pigments used in the manufacture of paint are discussed in the following pages.

May 1, 1932

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs, and Mine Management 156, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif.]

Jan 1, 1952

By Hamid Maleki

Prudent design of coal pillars in any mining system requires an estimation of in-situ pillar strength, overburden lateral load transfer capability, and a failure criterion. Pillar strength is typically determined using one of several different empirical pillar strength formulas. For coal reserves in the U.S., a new pillar design method was proposed based on extensive U.S. field measurements in underground mines (7) which accounted for confinement effects. Field measurements in seven U.S. seams indicated highest strength for some Utah mines where the coal seam developed high confining stresses. Lower strength was measured in structurally controlled seams. This method is expanded here including the data from the weaker tertiary coal measure rocks and lower confinement for pillars with low width-to-height ratios. The determination of how much load a pillar is expected to take is partially dependent on the ability of overburden to transfer load laterally; this is useful for selection of panel width and barrier pillars size in select mining applications where long-term stability is required in conservative designs. In caving mining systems, caving of the strata is influenced by geologic, mining and stress conditions and the released energies influences how the pillars react at loads approaching pillar strengths. Overburden deformation and caving mechanisms are analyzed in this paper in multi-panel extractions to enhance the understanding of load transfer, seismicity and coal bump control in deep western U.S. operations.

Jan 1, 2008

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4. N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvarl-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcade Bids. Santa Barbara, Calif.]

Jan 1, 1952

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1893 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management ` 188, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 8 Haward-Canfleld Bldg. Santa Barbara, Calif.]

Jan 1, 1952

By David J. Mack

A survey and critical appraisal of published information about Young's modulus was originally made by the writer because of a complete lack of information about this very important quantity in works on. mechanics, physical metallurgy, physics, and other sciences. It was felt that a comprehensive summary of such information about Young's modulus might be of general interest and may suggest new problems or lines of attack on other problems that involve E. Hence this paper has been prepared even though it is only a review, with no new ideas or experimental data. The references are only those used in assembling the paper. No attempt was made to compile a complete bibliography on the subject of Young's modulus. CalculatioX oP YouNg's Modulus from Theoretical or Empirical CoNsidera-tions Many attempts have been made to compute E from theoretical considerations. The earliest calculations were probably those of Tomlenson (1883) and Souther-land (1891), but Fess'enden4',~ made extensive calculations a few years later and arrived at the relationship: £ = 78.TOw(i)* where V is the atomic volume. In 1923, Peczalski, working from the same standpoint but with more information available on atomic structure, arrived at an identical relationship, which he expressed as: where B is a constant of value about 8 . 107, p is density and mis atomic weight; the atomic volume, of course, being ml p. Portevind4 immediately pointcd out that while the equations of Fessenden and Peczalski were true of the common metals, they gave low values for the refractory metals with high moduli (Fig. I). He showed (Fig. 2) that much better concordance was obtained by means of an empirical equation of the form: F- KT" where K is a constant; T the absolute melting point; V, atomic volume, and a and b constants of value approximately I and 2 respectively. This constant K in the Portevin equation is not necessarily the same for all elements, as shown by Thompson. Other equations for E based upon theoretical considerations have been derived by Honda and Yamada49 and Lasareff.50 The most recent calculations of elastic moduli based upon quantum mechanics are probably those of Fuchs He extended the method of Wigner and Seitz for calculating the lattice energy and compressibility of monovalent metals and computed the elastic constants of lithium, 18

Jan 1, 1946

By N. Morrison, I. Holl, R. Welyhorsky, A. Hempstock

ABSTRACT: The Victor diamond mine is located in the James Bay lowlands, 90 km west of the First Nations village of Attawapiskat. The project was the first of its kind in northern Ontario. The process plant was designed to produce a 95 to 98% by weight diamond concentrate through three stages of comminution, dense medium separation, and proprietary X-ray technology for final recovery. The plant was commissioned over a period of six months, commencing prior to substantial completion of construction. Through effective planning of the commissioning phase, the Victor mine start-up was safely completed nine months ahead of schedule.

Jan 1, 2011

By R. W. Raymond

EDWARD COOPER, was born in New York City, October 26, 1824. His father, Peter Cooper, to say nothing of manifold reasons for fame as an inventor and philanthropist, deserves to be remembered as a pioneer in the establishment of public schools; and it is not surprising that he sent his son to one of the democratic institutions in which he was himself so ardently interested. From the public school Edward Cooper went to Columbia. College, where he made the acquaintance of Abram S. Hewitt, who was first his tutor, afterwards his traveling companion, brother-in-law, business partner and life-long friend.* For twenty years I was the consulting engineer of the firm of Cooper & Hewitt, and also connected with the work of the Cooper Union, in which they were both deeply interested and faithfully active. On the basis of the intimate knowledge thus gained, I venture an estimate of Edward Cooper's character and career which, if not fully comprehensive, may facilitate a juster estimate than would be reached by the strident of those data which the modesty of the man permitted to be placed upon public record. Edward Cooper's mind was one of the most active, accurate and subtle with which I have ever come into contact: He had inherited from his father a sunny, benevolent temperament, and' the irresistible impulse to attack all new problems which challenged his attention. His thorough education had 'indeed made him wiser than his father, both in philanthropy and in technical inventions. He could condemn and reject a proposition which Peter Cooper would have embraced, in a splendid, though ignorant, faith that nothing was impossible to an. American, and that the word ? impossible " was simply a label,

Jul 1, 1906

By Hazel Lyman Nickel

Daring to try where others had failed, Herbert and Lou Henry Hoover translated from the Latin the principal (and first) textbook on the mining and metallurgical profession, De Re Metallica, 1556, which had been in use for two centuries and then had lain dormant for 350 years in a language unreadable except by a chosen few. Thus the Hoovers enriched the English tongue with a vitally important contribution to history in the fields of mining, metallurgy, and chemistry. To them it was a joint hobby, because they were actively interested in the beginnings of the mining profession in which they had both been trained. Illuminating the years of toil to perfect this translation shone their ideal of service to humanity, since, in the Preface, they refer to their task as "a labour of love", which had to find the moments for its execution in night hours, weekends, and holidays, extending over a period of about five years. And they add: "If the work serves to strengthen the traditions of one of the most important and least recognized of the world's professions, we shall be amply repaid". While a student at Stanford University, during the years of 1891-95, Herbert Hoover had become familiar with a copy of this Latin mineralogy classic, De Re Metallica, a rare book in the private library of Dr. John C. Branner, at that time head of the department of geology and mining. Another Stanford student in geology was also examining and studying the ponderous volume of twelve 'books'. She was Miss Lou Henry, of Monterey, who graduated in 1898, and the following year became Mrs. Herbert Hoover. Interwoven through the tapestry of their life experiences gleamed the silver thread of their interest in this mediaeval Latin textbook. Just nine years lacer, the Hoovers had commenced their translation, while they were in temporary residence in London after the seething years in China under the shadow of the Boxer rebellion.

Jan 1, 1949

By PAUL M. Tyier

NOW that analytical chemistry has gone so far to debunk early misconceptions about minerals, the fact that the light of exact knowledge still fails to illuminate many dark corners is often overlooked. By combining the skills of the physicist with those of a chemist, the identification of minerals has become an exact science and the presence of even minute traces of impurities and extraneous elements is readily revealed by spectrographic means, Granted that we can learn all there is to know about the composition of a substance and even about its physical propertied (which latter assumption is somewhat far-reaching) it still does not follow that we clearly understood its commercial designation or utility.

Jan 1, 1941

By Kefton H. Teague

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included.

Jan 1, 1950