Search Documents

By John C. Stankus

To improve mine roof bolt performance, Jennmar Corporation commenced the design and development of a new roof control sys- tem. This new system designated "Insta'l Compression", not only improves safety, but is more cost efficient due to reduced amounts of resin needed per bolt installation. In this paper the research and development of this new system will be outlined. Much of the information presented will be actual test data from various underground operations in Alabama, Kentucky, and Pennsylvania. The development of this system will also cover the design of a new expansion shell, resin compression ring, anti- friction washer, and upgrading of material specifications.

Jan 1, 1990

By Richard A. Cubeta

Precast concrete segments have been used in sanitary sewer tunnel design for decades. Federal mandates (reduction in heavy metals and I & I), and system design changes (increased retention times) and other factors have exacerbated corrosion problems. In an effort to combat the ever-growing effect of microbiologically induced corrosion, owners, engineers, and designers have been specifying thin-film lining systems to protect precast concrete segments. These systems have compatibility and installation issues. Chemical additives or calcareous aggregates have been utilized in precast concrete, but have only proven to retard the rate of corrosion and do not eradicate the problem. Solid cast polymer segments are stronger than precast concrete, do not require linings or coatings, are impervious to ground water infiltration, and, above all, are inherently corrosion resistant through and through.

Jan 1, 2008

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004

By Pierre Lacoste-Bouchet, Ian Orford, Mike Cooper

"The Brunswick Mine ore requires fine grinding to achieve liberation of minerals. With 25mm slugs as the grinding media in the ball mill, there was a limitation of a P80 of 25 microns on the CuPb regrind circuit. Results from pilot plant testing showed that the separation efficiency could be increased through fine grinding with a P80 of 15 microns.Options considered were the capital expenditure for new fine grinding equipment such as a vertimill or the use of the present ball mill equipment with smaller media. The Wheelabrator Allevard Enterprise (WAE) millpebs product was chosen because it was a smaller media with a distribution of steel pellets between 5 to 12 mm.With millpebs the grinding product was reduced in size from a P80 of 25 microns to a P80 of less than 19 microns. The power draw to achieve the finer grind was 13% lower while the media consumption was 57% higher.The millpebs grinding media was also tested on the zinc regrind mill. The purpose of the trial was to understand what the media consumption and power draw would be with the charge lowered to achieve an equivalent grind as obtained with the slugs. The media consumption was approximately the same and the power draw was reduced by 30%.INTRODUCTIONThe Brunswick Mine ore is a complex Pb-Zn-Cu-Ag sulphide ore with the grain size of the minerals varying from submicron blebs to particles up to several mm in size. The ore is ground progressively finer in stages. The first step of grinding occurs in the SAG mill circuit. The product sizing 80% passing 95 microns is fed to the CuPb prefloat stage (Cormier et al 2002). The tails from the prefloat is then further ground to a P80 of 35 microns for the CuPb rougher flotation. The final liberation for the CuPb circuit takes place in the CuPb regrind circuit. The regrinding mill further liberates the cleaner scavenger concentrate, second cleaner tails and third cleaner tails. The reasoning for the progressive grinding is to achieve fine grinding without having galena over ground due to its high specific gravity that preferentially sends it to the cyclone underflow."

Jan 1, 2006

By P. H. Reynolds, S. Liaghat, A. Zarasvandi

"Darreh-Zerreshk and Ali-Abad are two relatively small porphyry copper-type deposits in Yazd Province in central Iran. They are located within the central Iranian volcano-plutonic belt, formed above the collisional convergent margin of the Iranian lithospheric plate from the late Eocene to the Miocene. This paper discusses the geochemical characteristics of the igneous rocks, and 40Ar/39Ar geochronology of plutons and alteration phases associated with the Darreh-Zerreshk and Ali-Abad deposits. The deposits are spatially associated with igneous complexes that consist of older and barren granites intruded by intermediate-composition granitoids, which are the carriers of Cu mineralization. The granites have relatively high content of Nb, Y, and K, a prominent negative Eu anomaly, and were probably derived from melting of, or contamination of mantle-derived magmas by, continental crust. Porphyritic diorites, quartz monzodiorites, and granodiorites show enrichment in light rare earth and large-ion lithophile elements, depletion in middle rare earth elements, and have no negative Eu anomaly. These intermediate-composition granitoids were derived from melting of the upper mantle or lower crust, and their differentiation was controlled partly by fractionation of hornblende. A pilot K/Ar whole-rock dating study suggests that the pre-ore granites were emplaced in the Oligocene. Dating by the 40Ar/39Ar method of nine samples of secondary biotite and sericitized rocks from drillcore within the mineralized and altered zones in both deposits yielded a well-defined age of ca. 16 Ma. This date is interpreted to be the time of hydrothermal alteration and of porphyry copper type mineralization in this part of Iran."

Jan 1, 2007

In the past decade several significant intrusion-related gold deposits have been discovered in terranes historically exploited for tin-tungsten mineralization (eg Tintina Gold Province, Yukon and Alaska, Tasman Fold Belt, Australia and the Altaid orogenic collage in central Eurasia). This paper presents new data on the geological and geochemical characteristics of these deposits that links them to magmatic-hydrothermal processes and highlights their implications for exploration. New data from several intrusion-related gold provinces suggest that these deposits are found in areas that contain granodiorite to granite, but with a locally significant mafic component, have Rb/Sr ratios ranging between 0.1 and 1.0, and are moderately reduced (Fe2O3/FeO ~ 0.1 to 0.6) ilmenite series, metaluminous, I-types. The intrusions are distinct from porphyry copper intrusions and tin granites, but are more akin to tungsten granites. Hydrothermal fluid types vary with depth of emplacement in intrusion-related gold deposits and new proton induced X-ray emission (PIXE) data from syn-ore fluid inclusions in shallow and deep deposits provide fascinating insight into the variation in metal content between the different settings consistent with observed deposit metal associations. Exploration for intrusion-related gold deposits in tintungsten terranes should focus on regions that contain both mafic and felsic intrusion that are moderately reduced, metaluminous, I-type granites rather than terranes with dominantly highly fractionated, strongly reduced, peraluminous S-types. Intrusion-related gold systems occur in variety of deposit styles (in part controlled by host rock, proximity to granite, and depth of emplacement) and exploration geologists need to be aware of the variety of target types in and around the intrusive environment, and be able to recognise whether they are exploring a shallow or deep intrusion-related gold setting.

Jan 1, 2005

By Adam Gray, Emery Gray

State-of-the-art seismographs can be employed to assist the blasting engineer in understanding the propagation of vibration waves generated by blasting. Wave traces and frequency plots are used to adjust shot loading and timing, especially around close or near- field structures. Successful close-in blasting vibration monitoring requires careful consideration of the following: Geophone locations Mounting of geophone both on structures and in the ground Differences between ground motion and structural response This presentation will discuss methods used to control and monitor blast-induced ground and structure motions. Case histories are presented to illustrate seismic monitoring used as a tool to control vibrations and guide the blaster in the design process.

Jan 1, 2005

Present roof bolting practices in the collieries of Australian Iron and Steel Pty. Ltd. are outlined. Roof support has been improved since introducing roof bolts and it is hoped to increase the reliability of the bolts still further.Expansion-shell, and split and wedge roof bolts five to eight feet long are placed by "Atlas Falcon" and "Fletcher" roof bolters. Both anchorage and tightening have presented some problems.Good panel supervision is required if systematic roof bolting is to be properly co-ordinated with coal production without unnecessary delay to either. Successful roof bolting can only be the product of conscientious men and supervisors who are all convinced of its value. A rigid operational code should be established early and maintained.INTRODUCTIONRoof bolting is a method of support which is permanent and reduces or eliminates the need for other support; The method was pioneered in America and was first experimentally investigated in Australian collieries at Elrington in 1949 (McKensey, 1953). Pneumatic installation methods were employed. Subsequently, a method of using standard hand-held electric coal drills was developed at John Darling Colliery (Horseman, 1954). Pneumatic roof bolting equipment was first operated in the collieries of Australian Ironand Steel Pty. Ltd (A.I. &. S.) in 1951. Since then various hydraulically operated mobile machines have been installed in Australian collieries and these, together with improved pneumatic equipment, form the two present basic methods of placing ,roof bolts. Roof bolt anchorage is achieved by either split and wedge or expansion-shell bolts.The two broad types of roof bolting are 1. consolidation of strata, and 2. suspension support.

Jan 1, 1961

By P. Falcão Neves

A detailed analysis of the geomechanical behaviour in rock cutting with a diamond saw is provided to obtain a better understanding of the mechanisms involved in the process. The energy of elastic deformation (before failure) and plastic deformation (post failure) was determined in uniaxial compression tests as well as the energy consumed per unit volume in the cutting process. The test samples are White and Ruivina marbles from Borba - Vila Viçosa in Portugal. Correlations between total deformation specific energy and cutting specific energy, normal and tangential forces and diamond indentation are analysed, and some conclusions are presented.

Jan 1, 2012

By Jim Wickens, Andy Cole, John Pekrul

"The roaster facility at Barrick Goldstrike Mine treats double-refractory sulfidic/carbonaceous gold ore. Prior to oxidation in the roasters, the ore is ground in two parallel dry grinding circuits utilizing 19’ Ø x 75’ double rotator mills. The design plant throughput was 12,000 dstpd. However, process improvements have significantly increased throughput rates by 25-50%. The current daily throughput record is 20,078 dstpd. Grinding circuit improvements contributing to this success include feed size reduction, ball size optimization, automatic ball charging optimization, and operating strategy changes. In addition to the changes already made, this paper discusses future optimization initiatives including on-stream particle size analysis and “real-time” ore hardness determination techniques.INTRODUCTIONBarrick Goldstrike Mines is located 29 miles Northeast of Carlin, Nevada, USA. Through 2001, the property has produced over 23 million ounces of gold making it one of the premier gold operations in the world.Prior to Barrick’s ownership, the property began producing gold from a small heap leach operation in 1975. The small-scale heap leach production continued through 1986, and in January 1987, Barrick acquired the property. Increased exploration activity by Barrick significantly increased gold reserves. In August 1988, a 4,500 dstpd mill facility was commissioned to treat high grade oxide ore. Also, heap leach operations had significantly expanded. In 1990, the mill was expanded to 6,000 dstpd, and the first autoclave was commissioned to treat refractory sulfide ore. By the end of 1996, the mill and pressure oxidation facility had expanded to 16,000 dstpd and heap leaching had ceased as oxide reserves were exhausted. In 2000, a roaster facility was commissioned to treat double-refractory sulfidic/carbonaceous ore."

Jan 1, 2003

By L. Malmgren, A. Ansell

This paper deals with the influence from blast induced stress waves on the performance of shotcrete support in the Kiirunavaara mine. Time histories of stress waves from blasting were obtained from measurements during production blasts in the mine, followed by failure mapping. A finite element model, consisting of beam and spring elements, was used to calculate the shotcrete response to vibrations from blasting. The modelling approach was similar to that of a building during an earthquake, with accelerations measured in-situ used as loads. The analysis showed that the calculated adhesive stresses exceeded the strength in the interface between rock and shotcrete near to the blasted ring. It also indicated that tensile rock failure did occur. These types of failure will presumably result in ejection of joint defined rock blocks or rock slabs and will require a ductile support, such as fibre reinforced shotcrete. The predicted failure was confirmed by the mapping, which also showed that the zone of failed shotcrete was much larger in areas with plain shotcrete compared to areas with reinforced shotcrete. L’influence de l’onde de pression générée par les sautages à la mine de fer de Kiruna sur la performance du béton projeté est étudiée dans le présent article. Les ondes créées par les sautages ont été enregistrées et les domages résultants ont été cartographiés. La réponse du béton projeté aux vibrations de sautage est étudiée à l’aide d’un modèle d’éléments finis, constitué de poutres et de ressorts. L’approche est similaire à celle d’un immeuble subissant un tremblement de terre, avec les accélérations internes utilisées comme charges. L’analyse montre qu’à proximité des sautages, la contrainte adhésive dépasse la résistance de l’interface roche-béton. L’analyse confirme aussi l’existence de ruptures en tension. Ces types de rupture induisent probablement l’éjection des blocks définis par les structures du massif rocheux et requierent un support ductil, comme du béton projeté renforcé par exemple. Le type de rupture est confirmé par les observations de terrain, qui montrent aussi une extension plus importante des domages lorsque le béton projeté n’est pas renforcé. In diesem Konferenzbeitrag geht es um den Einfluss, der aus einer Sprengung hervorgerufenen Schwingungswellen auf die Ausführung der Spritzbetonverstärkung in dem Kiirunavaara Bergwerk. Die Aufzeichnungen der Schwingungswellen von Sprengungen gemäß einer Fehlerkartierung beziehen sich auf Messungen, die während der Sprengungen durchgeführt wurden. Ein Finite Elemente Modell, bestehend aus Stab- und Federelementen, wurde für die Berechnung der Spritzbetondeformation in Bezug auf die Schwingungen aus Sprengungen angewendet. Die Modellierungsmethode war ähnlich der eines Gebäudes während eines Erdbebens anhand der gemessenen Beschleunigungen vor Ort, die als Lasten benutzt wurden. Die Untersuchung hat gezeigt, dass die berechnete Haftspannung größer war als die Festigkeit in der Verbindung zwischen Gestein und Spritzbeton in der Nähe des Sprengungscentrums. Die Analyse hat gezeigt, dass die Zugfestigkeit des Gesteins versagte. Diese Arten von Versagen werden als Folge der Herausnahme von Gesteinsbrocken oder Gesteinsplatten erklärt und benötigen eine faserverstärkte Spritzbeton. Das vorausgesagte Versagen bestätigte sich beim Kartieren, welches auch zeigte, dass die Zone des versagenden Spritzbetons in Bereichen mit unverstärktem Spritzbeton viel größer war als in Bereichen mit armierten Spritzbeton.

Jan 1, 2003

By R. Hummel

When the slope angles of the southern side of the Venetia open pit were required to be flattened by some 20 degrees after an analysis completed by De Beers geotechnical engineering in conjunction with SRK, the additional waste stripping tonnage generated was in the order of some 70 million tons. The potential cost of having to move this tonnage had a significantly negative effect on the Net Present Value of Venetia Mine, challenging the viability of the third pushback and rendering a potential fourth pushback completely uneconomic. This paper details some of the innovation that went into the design and planning process undertaken to virtually negate the instantaneous effect of the flattened slope angles and the associated waste tonnage as well as further improve the NPV of Venetia Mine and bring the fourth pushback back into economic viability. This process has become known as NPV+ and is anon going exercise in waste reduction/deferment and revenue advancement.

Jan 1, 2001

By P. J. Closmann

Steam zone growth as a function of time has been calculated for the case of constant rate steam injection into a preheated reservoir. To simplify the calculation a linear temperature profile has been assumed in the cap and base rock at the start of steam injection. The results indicate that at early times augmentation of steam zone growth due to preheating should be greatest. At longer times the steam zone development becomes close to that calculated with no preheating. INTRODUCTION With the increasing application of thermal recovery processes to recover viscous oil, cyclic steam injection has become important in many large-scale projects. In this process, the cycle of steam injection followed by oil production is repeated a number of times. At the beginning of the second and later cycles, steam is injected into a reservoir that has already been heated but that has lost part of its heat both in produced fluids and by conductive heat loss away from the injection zone. In such a case, the temperature level of the injection zone and the temperature distribution of the surrounding rock will affect the growth of the steam zone developed during the subsequent steam injection. Knowledge of the size of steam zone developed is important in determining the amount of oil displaced and the extent of heating in the reservoir. It is also useful to be able to compute the size of the steam zone for cases where thief zones take most of the injected steam. This paper presents a fairly straightforward method of estimating the steam zone developed in a preheated formation, based on certain simplifying assumptions. Some cases of steam injection into a reservoir at its original temperature have already been considered elsewhere.1-3 Because it is difficult or impossible to obtain an accurate representation of the temperature distribution in the reservoir some time after initial heating has taken place, in this work, a linear temperature profile in the cap and base rock is assumed (Figs. 1A and 1B). The linear profile has the advantage of yielding heat flow equations that

Jan 1, 1969

By James A. McGrath

"The predominant key word associated with all commercial blasting methods is “safety”. Safetyshould take precedent over all other aspects of the entire explosives industry which on a wholehas had an excellent track record as to number of injuries per unit of hours worked at all blastsites throughout our country."

Jan 1, 1999

By Andrzej Walentek

This paper presents the results of numerical modeling of the fractured zone around longwall gateroads. The numerical computations have been based on the results of underground measurements of the fractured zone around longwall gateroads, which were performed for various geological and mining conditions and measured with the use of the endoscopic method with a digital camera. Having results of the underground investigations, trials of duplicating them by the Finite Element Method using software PHASE and the Hoek-Brown failure criterion were performed. In order that the fractured zone predicted by the model-based computations closely simulate that measured underground, some selected parameters in the Hoek-Brown failure criterion were modified based on the earlier determined relations used for prediction of the roof-to-floor convergence in longwall gateroads. As a result, the model-based computations produce results very close to those obtained from the underground measurements. Determination of the fractured-rock zone around the mine roads is of great importance to mining practice, especially in planning and designing supports for longwall gateroads. The influence of the front abutment pressure causes the fractured rock zone around the roads to increase and results in an increase of support load. Moreover, proper determination of the fractured rock zone is one of basic elements in the process of planning roof bolting for mine workings.

Jan 1, 2009

By B. Goard

"IntroductionCemented backfill has been placed underground in slurry form in Inco Limited's Ontario Division mines since the early 196Os. The slurry was traditionally mixed on surface at between 65 and 70 wt% solids* and transported underground via gravity through a borehole-pipeline distribution system. This method of placement, while simple and dependable, has proven to be costly because of the large amounts of transport water involved.A significant quantity of the slimes buildup on mine levels is caused by the backfill water carrying cement and other fine material out of the stopes. The level cleanup and eventual pumping or hoisting of the slimes and water back to surface result in substantial indirect backfilling costs.The cement that remains in the stope is always overhydrated because of the high water cement ratios that exist. As a consequence, high concentrations of Portland cement must be added to the backfill to produce the fill strengths required for the different mining methods.Pouring backfill at these densities also demands extensive fill preparatory work in the stopes to withstand the hydraulic heads created by the slurried fill. This, along with the delays in pouring necessary to allow for water drainage, result in significant losses in productivity.These negative aspects of slurry placed fill has led Inco Limited to investigate several methods of transporting backfill underground via pipeline, at higher densities (i.e. 75 to 95 wt.% solids). Three separate transport methods are presently being experimented with by the Company's Mines Research Department. Each utilizes a different technique or form of flow transport, i.e. concrete pumping technology, high density slurry flow, and pneumatic conveying."

Jan 1, 1987

By R. Burger, M. Masukawa

Cato Ridge Alloys (CRA) is a joint venture company between Assmang of South Africa, Mizushima Ferro Alloy Company (MZK) and Sumitomo Corporation from Japan. Negotiations for the formation of the company started in 1992 with the joint venture agreement signed on the 19th September 1996. MZK was to supply the technical know how for the production of Medium and Low Carbon FeMn while Assmang was to manage the day to day activities of the company. Sumitomo Corporation was to act as facilitator between Assmang and MZK and, together with Ore and Metal are responsible for the marketing of the refined products. The conceptual design of the plant started in December 1996 and the first charge of molten high carbon ferromanganese metal was charged on the 19th January 1998. Problems experienced during the initial startup period were addressed resulting in substantial operational improvements. A build-up in the stock of fine metal was addressed through the development of a process to remelt the fine metal, the development of a market for fine metal and the upgrading of the crushing and screening plant to reduce the generation of fine metal. The mass yield from High Carbon Ferromanganese to Refined Ferromanganese was increased through the implementation of statistical process control, changes to the blowing patterns and the development of a sampling device for taking samples during the process. Converter refractory consumption was reduced. This was achieved on the converter by improving the cooling of the converters with the installation of cooling fans and cooling fins. The heating schedule of the converters was changed for improved refractory life. Production schedules were modified to allow cooling of the refractory between low carbon erromanganese charges. Additional changes made to improve operations were: ? Changing from mehanite casting trays to metal fines beds. ? Installation of sonic horns in the baghouse to prevent the bridging of dust. ? Improved welding on the lance tips.

Jan 1, 2004

By D. Rahal

All ores have an economic optimum particle size (Wills and Napier-Munn, 2006). This optimum value is often a compromise between the need to achieve adequate liberation for the efficient separation and recovery of valuable minerals and the energy consumed by the crushing and grinding process. It has been recognized for nearly three decades that grinding is the most expensive and least efficient stage in mineral processing (El-shall and Somasundaran, 1984). At that time it was estimated that grinding consumed between 25 and 70% of the total power required in mineral processing. This recognition drove the development of new stirred mill fine grinding technology in the 1990s (Jankovic et.al, 2003; Enderle et. al., 1997; Massey, 2008). These milling technologies have a reduced energy consumption compared to traditional fine grinding using ball mills. In the ?coarser? fine grinding applications this improvement is approximately 30%. The benefits increase to above 50% in ultrafine grinding applications (Lichter and Davey, 2006). Despite these gains, the US Department of Energy reported that an additional energy savings of up to 37% is possible in the minerals industry. They identified continuing research and development and implementing best practices in both grinding and materials handling as the primary avenues for the additional reduction (BCS, 2007).

Jan 1, 2011

By C. Vipulanandan

It is critical to monitor the ground conditions during excavation and drilling of boreholes during construction to identify possible changes in the soil and rock formations. Drilled shafts are increasingly used as foundations to support structures, bridges and other facilities in geomaterials such as soft-rocks and hard clays. Locating the bottom of the borehole during construction with the required design strength is critical. Hence developing a simple device that could be easily adapted/used with the drilling tool was of interest in this study. Determining the shear strength of the geomaterial in the borehole and at various elevations including the bottom of the borehole can lead to better quality control of construction by identifying the various layers based on strength. In this study, a down-hole penetrometer (DHP-CIGMAT) was designed, built, calibrated and tested in the field to determine its effectiveness in measuring the strength of soil/soft rock in the boreholes. Based on limited field tests, linear correlations between geomaterial strengths and DHP-CIGMAT deflection have been developed. The DHP-CIGMAT can be used to identify soils and soft rocks.

By P. J. Rua

The Piedras Verdes copper mine is a new run-of-mine (ROM), heap leach, solvent-extraction/electrowinning (SX-EW) operation located 21 km (13 miles) north-northwest of the town of Alamos in the state of Sonora, Mexico. The Piedras Verdes copper mine is wholly owned by Frontera Copper Corp. (FCC), a Canadian corporation, through its 100 percent beneficial interest in Cobre del Mayo S.A. de C.V. (CDM), a Mexican registered company. The January 2008, minable reserves were estimated to be 193.6 Mt (213 million st) at a grade of 0.36 percent copper. The overall recovery of total copper was estimated to be 61.9 percent. The property has an additional 17-year life and is designed to produce 31.7 kt/a (70 million lbs/year) of cathode copper. Construction commenced in early October 2005. The first copper cathode was produced 12 months later at a total capital cost of $100 million. Elevations at the site range from 150 to 300 m (490 to 985 ft) above sea level. The area has excellent infra-structure in the form of towns, power, water, roads, rail, airfield and access to the deepwater port of Guaymas (Fig. 1). The surrounding area is also famous for its numerous polymetallic (lead, zinc, copper, silver and gold) epithermal veins. Some of these were mined for more than 200 years and provided the wealth on which the town of Alamos was built. The original village of Piedras Verdes was located in the area of the proposed openpit mine and, consequently, it was necessary to construct a new townsite 6 km (3.7 miles) to the south before project development could commence. The new town site (Fig. 2), complete with power and water supplies, roads, sewer system, schools, clinic and recreational facilities, was completed and occupied by 49 families in September 2005. CDM received its remaining permits from the Mexican environmental authorities on Sept. 20, 2005. This enabled the company to proceed with full-scale development. CDM owns or controls 27 mining concessions covering the resource. Surface rights to the Piedras Verdes project were controlled by four Ejidos (communal agrarian and/or ranching societies) and five individual landowners. CDM has acquired all surface rights necessary for its mining operations and associated facilities either through outright purchase or long term lease agreements.

Jan 1, 2008