Search Documents

By Wenting Zhu, Liqing Chen, Junjun Cui, Zhenye Chen

In this presentation, a low carbon high strength steel microalloyed with Nb and Ti was processed by thermo-mechanical controlled process (TMCP) containing two stages of controlled rolling. The austenite with various grain sizes was obtained by austenitizing this hot-rolled steel at different temperatures. And the effect of austenite grain size on bainitic transformation was investigated in a dilatometer to reveal microstructural change. The results showed that the microstructure of the hot-rolled steel was mainly composed of granular bainite, lath-like bainite, and martenite/austenite constituents (M-A constituents). With increasing the austenitizing temperature, or increasing the austenite grain size, the microstructure was changed from granular bainite to lath bainite. When the steel was reheated to a lower temperature of 860 ºC, a relatively higher start temperature (Bs) was measured for bainitic transformation. This was mainly caused by the formation of solute-depleted region in the austenite and the promotion of the granular bainitic nucleation. The highest reaction rate occurred at austenitizing temperature of 1000 ºC with fine grain size, while the coarse austenite grain can lead to a sharp increase in the amount of bainite. An analysis was made on the kinetics of bainite transformation which was controlled by the volume diffusion of C atom.

Oct 1, 2019

By L. Martins Demuner, D. Burzic, V. Cunha Aranda, F. L. Lourenço, G. Romeu Trindade dos Santos, F. Ramstorfer

For many years, Dynamic Soft Reduction has been regarded as a proper method in improving internal quality of slabs. Even though processes models improved significantly over the past years, the efficiency of Soft Reduction was always limited by the discretization error, which inherently exists if segment rollers cannot be positioned individually. The recently developed SRD segment type allows for an individual roller positioning within the mushy zone by avoiding any discretization deviation from the optimal gap. This paper provides a detailed technological overview of the SRD segments as well as operational results at their very first implementation at Ternium Brazil.

Oct 1, 2019

By Gabriel Oliveira Glória

Due to growing concern about the ambient impacts, lignocellulosic fibers are been investigated to replace the synthetic ones in polymer composites The giant bamboo fiber, a relatively unknown lignocellulosic fiber with potential for composite reinforcement, still needs to characterize for possible engineer applications. However the giant bamboo fiber has low adhesion with the polymeric matrix. In order to understand the interaction that occurs between the bamboo fiber and the polymer matrix is necessary to evaluate its physical and chemical characteristics. Therefore, the present work analyzed the giant bamboo fiber by means of Fourier Transform Infrared (FTIR) spectroscopy. The spectrum revealed main absorption bands typical of giant bamboo fiber specific molecular interactions.

Aug 16, 2017

By Gabriel Oliveira Glória

In the context of changing culture, the society is increasingly looking for environmentally friendly materials, the natural fibers appear as an option to substitute the synthetic. Among these natural fibers, the PALF fiber may be considered an option, but there is limited information about the flexural strength of epoxy composites incorporated with PALF fibers. Therefore, the objective of this work was to investigate the mechanical properties in bending tests of epoxy composites incorporated with up to 30% in volume of PALF fibers. The results showed that the PALF fiber increase the flexural strength of polymer composites.

Aug 16, 2017

By Daniel Hajduk

Efficiency of back up rolls depends mostly on two parameters – length of campaign and dressing amount after the campaign. The longer the campaign (in terms of rolled tones) is, the higher the dressing amount. To solve this task properly it is necessary to know the distribution of accumulated damage in the working layer of the roll caused by previous campaigns and by loads (separating force and bending) during present campaign respecting changing conditions of material properties (hardness) through radius of the roll. To find an optimum dressing amount an algorithm has been developed and specialized computer program will be presented, that takes real measured loads during the backup roll campaign, calculates fatigue damage in the roll and suggests relevant dressing amount. This can help to prolong service life of rolls, minimize the risk of spalls and reach maximum efficiency in terms of rolled tones/km per roll.

Jul 30, 2018

By Roman Vaynshteyn

In places where Blast Furnaces are usually located, climatic factors may be unfavorable. Raw materials may be exposed to e.g. rain during transport/storage, bringing moisture into the process with consequences for stability and hot metal cost. This paper describes a technology for drying and pre-heating pellets and coke in the stockhouse. It does not require additional handling or logistical equipment and does not introduce extra transfer steps and degradation. Not only can moisture content be reduced, it can be controlled to a stable level by the operator.

Aug 16, 2017

By Darina Manova

Plasma assisted surface modification methods have been used to nitride stainless steels in order to enhance hardness and therefore the lifetime of industrial components. Nevertheless, the corrosion resistance is not always preserved since it is very sensitive to the process parameters, either in implantation or in thermochemical diffusion techniques. AISI 316L stainless steel was plasma nitrided using three different techniques: Low Energy Ion Implantation (LEII), Plasma Immersion Implantation (PI3) and conventional DC pulsed plasma nitriding (DCPN). For each method several parameters were tested and some of them were selected to achieve the so called S phase of about 3 µm thickness and no nitrides precipitation. The nitrided layer was characterized with OM and SEM. Hardness was assessed on the surface with Vickers indenter and 25 g load. XRD was performed to characterize the S phase and to detect other phases if present and electrochemical corrosion tests were carried out in 3.5% NaCl solution. Although the S phase thickness in the three groups of samples was comparable, hardness was not and neither was the corrosion resistance. The PI3 samples were the hardest with the best performance in corrosion experiments, resulting in a higher breakdown potential and lower currents.

Aug 8, 2018

By Davide Onesti

Electrode regulation is the technology at the heart of the AC and DC Electric Arc Furnace. As such, in the last decade it underwent continuous improvement to maximize the EAF performances, in terms of process efficiency, machine utilization and operator safety. Given this background, Danieli Automation’s efforts in the field of electrode regulation have been focused on fast response to scrap cave-in, compensation of supply variations, automatic resonance detection, transformer protection, dynamic regulation of the electrical and chemical set-points, coordination and control of slagging and foaming agents, arc irradiance supervision. An extensive analysis of operator utilization and feedback was also carried out to develop an innovative system HMI. In this field, the choice of the variables shown to the user is the key aspect to allow a prompt process evaluation by the operator, who can refer to a condensed set of useful data. This paper will describe the innovative features and embedded models of the electrode regulation module (Q-REG+) and the supervision HMI, together with the effects of their application on EAF process efficiency and system usability.

Oct 30, 2017

By Oliver Schulz

This paper presents the latest references of the Siemens VAI slab casting technology. Following the connect & cast philosophy Siemens VAI has developed technological packages suitable for installation in existing casters of any original supplier, as well as for complete new machines. A major demand on new machines is to adapt quickly to different market demands. This requirement for flexibility can be divided into two actual trends. Firstly into casting a broad range of steel grades, thicknesses and width on the same machine and secondly having installed slab, bloom and billet caster in one steel plant to deliver all different types of needs on the market. Depending on the condition of the existing machine the focus of modernization ranges from the substitution of single components featuring state-ofthe-art technology to complete caster revamping projects. In this paper concepts and references for short machine outages and fast caster ramp-ups at moderate investment costs are presented.

Jul 30, 2018

By Peter Fajfa, Heinz Palkowski, Jakob Kraner, Matjaž Godec

The study of asymmetric rolling on the AA 5454 aluminium alloy plates was carried out. The plates were taken directly from the industrial hot rolled sheet. They were cold rolled on the laboratory mill with different rotation speed of the upper and the lower work roller with the strains around 33 % and 44 %. To get closer to the industrial conditions the maximal dimensions of the rolled plates for laboratory rolling mill and the special industrial lubricant were used. After deformation the plates were annealed to the soft condition. This research was focused on all possible effects of asymmetric rolling: The reduction of rolling force, the increase of strain at same set roll gap, bending of workpiece, finer microstructure, more heterogeneous textures and as a consequence of that better mechanical properties. The asymmetric rolling with favourable mechanisms in the deformation zone has created the material with the homogeneous hardness in the cross section and with lower anisotropy, which is crucial for improvement of formability properties of aluminium work hardened alloys and to get closer to properties of steels. In the presented paper the general impact and different effects of speed difference of rollers was investigated on cold rolled aluminium alloy. Obtained and analysed results explain the function of asymmetry in rolling process and the options to implement the asymmetric rolling in industrial plant.

Oct 1, 2019

By Jan Lückhoff

The introduction of the EAF Quantum furnace by Primetals Technologies represents an important milestone in the field of electric steelmaking during the last 15 years. In this process the latent and chemical heat of the off-gas generated during a melting process in an EAF is used to pre-heat scrap in an integrated shaft prior the melting of the scrap in the vessel. Combining proven own technologies, Primetals EAF Quantum enables nearly continuous process, cutting down idle times and enhancing availability for production. The essential benefits will be shown in this Paper.

Aug 16, 2017

By Mohammad Masoumi

In the present study, API 5L X70 pipeline steel samples were deformed by hot-rolling cooled in air or quenched in water and subsequently tempered at different temperatures. X-ray diffraction (XRD) and electron backscatter diffraction (EBSD) technique were used to analyze the texture evolution from the initiate state to rolling and tempering state at mid-thickness and near surface plane of all samples. The results showed that the mid-thickness region is richer in {100}//ND oriented grains known as more susceptible to crack formation and growth through. Hot deformed specimen showed dynamic recrystallization grains while quench tempered sample at 700°C evidenced recovery and grain growth.

Aug 16, 2017

By Bruno Alves Resende, Antonio Adel dos Santos

Temperature, microstructure and dimensions are the main material parameters to be controlled during hot rolling of steel. Although thermal mathematical models have long been developed and applied for hot strip rolling, each Hot Strip Mill (HSM) must have its own model adapted to its facilities. Thus, a mathematical model for temperature evolution during rough rolling has been developed for the Usiminas HSM at Ipatinga Plant. The model achieved a high level of accuracy, which was assessed by comparing measured values of temperature at the hot strip mill entry with the calculated ones, the difference ranging from 9°C to 17°C. Application examples have shown that the slab can be occasionally stopped before start of rolling for as long as a couple of minutes without compromising its further processing. On the other hand, if the transfer bar stops after rough rolling even for short time, further processing in the HSM can be hindered, due to excessive temperature drop. In case of such abnormal line stop, the model can be used as a tool for decision-making to either continuing the planned rolling schedule or to changing the route, thus improving the overall rolling process.

Oct 1, 2019

By Guilherme Guidugli

The hot blast stoves are a regenerative heat exchange system, accounting for 10 to 20% of the total energy requirement in an integrated steel plant, responsible for the supply of about one-third of the blast furnace heat input and responsible for a constant flow of hot air to the blast furnace, according to the required production. Because of their important role in the hot metal production, a stable operation and an appropriate combustion control is necessary. This paper aims to present the results of an investigation and modifications performed as an operating multi-furnace plant, as well as the parameters considered to ensure thermal equilibrium, improving in the stoves heating cycle.

Aug 16, 2017

By Luca Tommasi

Danieli complemented its wide range of production plants for the iron and steel industry with a further step upstream into iron ore pelletizing and beneficiation. Danieli has engineered and constructed a state of the art and fully automated pilot plant facility – pot grate and sinter box – at Altos Hornos de Mexico S.A. (AHMSA) Pelletizing Plant, Monclova, Mexico. Installation and commissioning were completed in October 2009. Key features of the pot grate include the avoidance of the need for operator intervention during the test, automatic system preheat, absence of dead time, heat recuperation system with an air/air heat exchanger, oxygen control in preheating and firing with zirconia oxygen analyzer, possibility to test deep beds up to 625 mm. A series of projects have been accomplished by AHMSA availing of the pot grate facility with the aim to enhance pellet plant productivity and to reduce operating costs. The results obtained by use of Danieli pot grate combined with the experience and skill of plant operators has shown significant technical and economical benefits thus fully justifying the initial investment made by AHMSA and confirming the importance of having an in-house testing facility in order to optimize industrial plant operations.

Aug 16, 2017

By Armando Vazquez

Steel Dynamics Inc. (SDI) and Tenova Goodfellow Inc. (TGI) have successfully commissioned the first hybrid extractive/laser system for continuous and full spectrum analysis (CO, CO2, O2, H2 and H2O vapor) on two twin shell furnaces at Butler, Indiana. NextGen® technology using off-gas analysis as a main tool for EAF practice optimization is a proven effective method for improving plant productivity. Significant benefits attributed to the NextGen® system are operational cost reductions through the use of real-time dynamic control of chemical energy and improved environmental conditions through reduced GHG emissions. Additionally, the implementation of Tenova’s Water Leak Detection Technology® has shown results as an effective tool for operators to identify in real-time the presence of water during both reducing and oxidizing conditions. This paper will include project details, trials and results and will also outline the latest hardware developments and multipoint capabilities

Oct 30, 2017

By Daniel Stickel

Current political, economic and ecological guidelines demand the increase of power densities of nearly all machinery parts today. In order to further lower the wear rate towards the ultra-mild sliding wear regime an integral approach is needed, which has to regard contact conditions, surface topography, surface chemistry, as well as sub-surface properties. Still there are no simple parameters to classify the performance of tribosystem. In this study the area and volume affected by tribocontacts are calculated by means of a three dimensional elastic-ideal plastic contact model. The surfaces are generated by means of conventional machining procedures and characterized by scanning white light interferometry. The further input data as to normal and friction forces are derived by ultra-mild sliding wear tests under boundary lubrication conditions of carburized steel against carburized steel and 52100 steel against case-hardened spheroidal cast iron. This contribution will depict the distinct influence of the topography on friction and ultra-mild sliding wear of common Fe-base materials and point on the marked importance of highly localized effects, which govern the acting mechanisms.

Jul 31, 2018

By Anna Carolina Cerqueira Neves

Synthetic fibers have been gradually replaced by lignocellulosic fibers. Compared to the synthetic fiber, natural fiber showed economic and environmental advantages presenting interfacial characteristics with polymer matrices that favor the impact energy absorption by the composite structure. However, so far little has been reported about the hemp fiber embedded in polymer matrices, such as tensile properties. This study aims to evaluate the resistance in tensile tests of epoxies composites reinforced with different percentages of hemp fiber. Tensile tests were submitted with percentage of 0%, 10%, 20% and 30% incorporated hemp fiber in epoxy matrix. The tensile strength and deformation substantially increased the relative amount of hemp fibers incorporated into the polymeric matrix.

Aug 16, 2017

By Jean-François Stumper, Mario Moser, Mark Kruessmann, Volker Langer, Daniel Bastos Martins Cruz, Claude Meisch

The latest generation of probes and casthouse machines provide a wealth of data that has not been available a few years ago. The evaluation of this data gives direct feedback to improve the blast furnace efficiency, the equipment maintenance and design and it allows the early detection of critical or deviating process situations. A stable operation with lower operation and maintenance costs are the final customer benefits.

Oct 1, 2019

By Josef Maierl

For the production of advanced high strength steel grades (AHSS) like API X80/X100, dual-phase, martensitic and complex-phase grades a number of hot strip mills need to extend their limits in terms of power and flexibility. Especially for cooling and coiling of these new materials, Primetals Technologies developed the “Power Cooling” and “Power Coiling” technologies. Power Cooling combines the advantages of conventional laminar cooling or “low pressure cooling” with the newly developed “high pressure cooling” with highest cooling rates for flexible operation. The Power Coiler which is needed to coil those high strength grades especially at thicker gauges ensures reliable strip-coiling for a most economical production. To enhance the reliable production of high-strength steel grades for a wide range of strip dimensions, the automation system with its advanced models is an integral part to the mechanical design. In this context the paper presents examples for the installation of power cooling and power coiling in new and modernized HSM.

Aug 16, 2017