Search Documents

By George Comstock

THESE notes should be considered as a further discussion of Mr. S. W. Miller's paper on "Some Structures in Steel Fusion Welds."1 In that paper and the resulting discussion; several conflicting opinions were expressed as to the identity of the needles or small crystals present in oxyacetylene and electric welds. An interesting specimen of an electric weld examined by the writer seems to afford new evidence regarding the needles, that may be worth presenting at this time. The specimen consisted of a piece of 3/8 -in. (9.5-mm.) steel plate, about 2 ¼ by 1 ¾ in. (5.7 by 4.5 cm.) in size, on which some iron had been deposited by arc-welding to a depth of about 3/16 in. (4.7 mm.). The weld appeared to be a very good one, with no noticeable break or boundary between the plate and the deposited iron. Sections for microscopic examination were cut in three planes at right angles to each other through the deposited metal, two of these sections also extending through the steel base. After polishing in the usual way, the microscope showed that the deposited metal was full of very small, round, gray, oxide spots, while the steel plate contained quite a number of alumina inclusions and a little slag. The sections were etched with nitric acid in ordinary alcohol, and structures similar to those described by Mr. Miller were then displayed. Fig. 1 shows the typical appearance of the deposited metal, which was quite uniform in all three of the planes examined. The round dark-gray spots are oxides, and the pale angular crystals are evidently what, Mr. Miller called cementite and Mr. Jeffries martensite, while Dr. Ruder and Prof. Boylston suggested that they might be nitride. The boundary between this structure and the steel base was sharply defined under the microscope. Fig. 2 shows the structure of the plate just under the weld; this is almost martensitic and resembles a coarse-grained casting. This coarse cast structure soon became finer as the distance from the weld increased, finally, becoming very fine, with numerous small particles of sorbite. This very fine structure, shown in Fig. 3, became coarser in turn and finally merged into the original normal structure of the steel plate, shown

Jan 1, 1919

By L. E. Snow, L. F. Pett

AT the Utah Copper Pit of Kennecott Copper Corp. a versatile mobile drill unit has been developed and tested. Through increased drilling speed and additional available drilling time, an improvement of 233 pct in drill performance has been realized. Operators using drill power can quickly and easily convert the unit from a vertical to a toe hole drill. Drilling is done with the machine in line with the unit or at right angles to it. Table I covers the 1950 drill record at the mine, showing the types of machines used and the footage obtained. Development of the new units was prompted by a desire for solution of the following problems: 1—The ever-expanding operations within the Utah Pit, requiring some 65 miles of transmission pipe lines radiating from a central compressed air plant, have now taxed this compressor plant beyond capacity. While 100 lb per sq in. pressure is maintained at compressors, transmission losses from innumerable small leaks result in low terminal pressure at the drills. Fig. 1 illustrates that while terminal pressure varies according to size of air hose and fittings used, the average drill is operating on air pressures within the 60 to 70-lb range. The compressor plant is operated primarily for air rock drills. All drilling is done on day shift, but it is necessary to run two of the three 3720 cu ft capacity compressors during night shift in order to prevent drastic loss of pressure through leaks. On day shift all three compressor units are operated at capacity, so that there is no reserve safeguard available for extensive repairs to any compressor. The calculated volume of compressed air required for operation of 25 drills is but 33 pct of three day-shift compressors. While compressed air is being used to a minor extent for purposes other than drilling, it is felt that satisfactory substitute facilities could be pro- vided in the event that air lines were no longer available. 2—Drill performance has increased beyond the capacity of present 3-in. drifter machines. 3—The installation, maintenance, and moving of air lines in routine mining is a growing problem. The 2-in. level lines are placed outside electrification towers and must be moved to new location upon completion of each shovel cut. In addition to these moves it is often necessary to dismantle level lines so that excessive shovel spillage, or material covering track following a blast, can be pushed in the clear with bulldozers. Where level room is limited, it is often necessary to remove air lines in giving bulldozers room to prepare grades for wagon drills. In spite of precautions taken, many level lines become buried, twisted, and constricted, with excessive air loss resulting. Excessive back break in blasting often leaves several sections of air line suspended in mid-air. Occasionally air lines come in contact with defective electric transmission towers, so that holes are burned through pipe. 4—Rail-handling of drilling equipment such as wagon drills from one location to another requires considerable locomotive crane crew time. Any new unit developed should travel under its own power. 5—Present practice requires accessory material including hose, water pressure tanks, water barrels, drill steel, and bits to be transported by means of push cars when drill locations are changed on any level. 6—In order to supply numerous drill locations with material, many stock piles of new drill rods, drill bits, and other essentials must be left at strategic points, usually in the vicinity of powder magazines. This practice makes for poor housekeeping and contributes to the loss of supplies. Planning the Unit It was felt that a mobile drill unit which would rectify the foregoing problems should meet certain demands: 1—It must furnish compressed air to operate a 4-in. rock drill at a pressure of 90 to 100 lb.

Jan 1, 1953

By G. W. Thomas

A simplified mathematical model of underground conduction heating in a system of limited permeability is presented. The model applies to underground retorting of oil shale, or to reservoirs containing extremely heavy oils. We assume that heat is introduced at a constant rate into a horizontal fracture which communicates between wells. The radial temperature distribution along the fractured surface is approximated by a step-function. Heat transfer away from the fracture is assumed to be by vertical conduction, and all convection effects are neglected. The model also takes into account the possible temperature dependence of thermal conductivity. A general expression for calculating the growth of the step-function temperature distribution with time is derived. The use of this expression and solutions to the one-dimensional heat equation make it possible to construct isotherms. Expressions for calculating .oil recovery, well spacing and heat efficiency are also given. An example calculation is presented for the conduction heating process in oil shale. Finally, the effect of the heat transfer coefficient between the gas and the fracture boundaries is investigated. INTRODUCTION Thermal recovery processes of oil recovery fall into the four general areas of hot fluid injection, forward combustion, reverse combustion and conduction heating. The first three of* these processes have been rather extensively studied in the past decade from both the experimental and theoretical points of view. As a result, it is possible to make reasonable engineering predictions and analyses of these processes. Little attention has been devoted, however, to the conduction heating process other than to note its possible utility.I To a certain extent, conduction heating cannot be divorced from the other regimes cited above, insofar as these provide the source of heat energy. In the conduction heating process, heat is introduced (either by combustion in the forward or reverse mode or by hot fluid injection) into a small fraction of the total reservoir thickness. This fraction may be either a streak of high permeability or an interwell fracture. Heat penetrates by conduction into the adjacent, less permeable regions of the oil-bearing rock, where the direction of conduction is essentially perpendicular to the streak or fracture. The heated product then drains by gravity or is gas driven to production wells. Conduction heating is probably most applicable to systems containing immobile bitumens such as tar sands and oil shale deposits and perhaps to low-permeability reservoirs containing highly viscous crudes. The mechanism also acts in combination with other thermal processes where fingering or overriding of a bed occurs. It seems probable that in at least one field test, conduction heating of this type was very influential.2 In this presentation we give a first approximation to some of the quantitative aspects of conduction heating. Marx and Langenheim3 treated a similar problem where they focused attention upon the injection interval, which spanned the total reservoir thickness. In their model, conduction heat losses to the bounding media imposed a practical limit on the calculated heated area. In the present study, however, we shall confine the injection interval to a small fraction of the reservoir thickness and assume it has no heat capacity. We therefore direct our attention to regions outside the injection interval into which the conduction of heat is beneficial. In particular, we will endeavor to locate specific isotherms in the media bounding the injection interval. Furthermore, we will construct our model to allow the thermal conductivity to vary arbitrarily with temperature. Thus the model will be applicable to underground retorting of shale where variations in thermal conductivity may be important. THEORY We consider the rock matrix to have no or, at best, a very limited permeability; consequently a

Jan 1, 1965

By J. C. Deppe

A method is presented for calculating approximate injection rates in secondary recovery operations. The method can be applied to cases of unequal fluid mobilities, irregular well patterns and boundary patterns. The steady-state pressure distributions for the four flood patterns reported by Muskat and for five additional patterns reveal that most of the difference in pressure between the injection and producing wells occurs in regions around the wells which can adequately be described as regions of radial flow. This leads to a method of calculating injectivity by approximating the flood pattern with radial flow elements (or a combination of radial- and linear-flow elements for some patterns such as the direct line drive). Irregular and boundary patterns can also be approximated by radial and linear elements. Each of these elements can be described by radial-and linear-flow equations and the results combined as series flow resistances to give an approximate equation for the initial injection rate. The mobility ratio does not affect the initial rate; therefore, if the well pattern is one of those regular patterns for which theoretical rate equations have been derived for unity mobility ratio, the approximate initial rate equation can be improved by adjusting it to match the theoretical equation. The available theoretical rate equations are listed, including five new cases. As the flood progresses, the injectivity changes because in general the flood front will divide the pattern into areas of different fluid mobilities. Simple shapes can be assumed for the flood front so that both areas can be divided into radial- and linear-flow elements. Radial- and linear-flow equations are applied to these elements to account for the change in flow resistance behind the front. To calculate injection rates after breakthrough, it is necessary to know the sweep efficiency at breakthrough. Areal sweep data are available in the literature for a number of patterns, and sufficiently accurate breakthrough sweep efficiency can be estimated from these data if it is not otherwise available. Again, simple shapes for the flood front can be assumed after breakthrough, and injection rates can be calculated for the remainder of the flood. When areal sweep data are available, these data can be used to cbeck. the calculated injection rates after breakthrough. Injection rates calculated by this approximate method compare favorably with available model data. INTRODUCTION When the fluid mobilities in the swept and un swept regions are equal, the injectivity will not change as the flood front advances; and for regular patterns it can be calculated by mathematical formu1as.l When the fluid mobilities in the swept and unswept regions are not equal, the injectivity will increase or decrease as the flood front advances. In this case, the injectivity has not been calculated by analytical means for any practical well pattern; and, furthermore, scale model and analog4,6 results have been published only for the five-spot pattern. The main object of this paper is to present an approximace method for calculating injectivity for the case of unequal mobilities. The method can be applied to regular, irregular and boundary patterns. Before the approximate method is discussed, the analytical formulas for equal mobilities will be summarized, and the analytical solution for radial flow with unequal mobilities will be used to show how the injectivity changes as the flood progresses. EQUAL MOBILITIES, REGULAR PATTERNS In a flooding operation the injectivity, the rate at which fluid can be injected per unit difference in pressure between injection and producing wells, depends on basic physical properties and, in addition, on three variables to be treated here—the area of the swept region, the fluid mobilities in the swept and unswept regions, and the well geometry (pattern,

By Hubert D. Keiser

An observation that is finding fresh confirmation in the leadership of the Allied Nations is "When the need arises, a man will rise to fill it." Much the same can be said of industrial advances in the current emergency. Events and circumstances have created needs for new materials and stimulated the inventive genius of man to fill them. The timely development of fibrous-glass manufacture, in relation to present war needs, is a case in point. Historical Summary It is probable that the first glass fibers produced by the hand of man were made about 4000 years ago. Successful production of glass fibers for manifold industrial and military uses, on any scale that could begin to meet present needs, has a history spanning a scant four years. The American processes that brought this young industry into being were developed between the years 1931 and 1937; research and manufacturing efforts were consolidated to create a commercially satisfactory operation as late as November 1939. In the 40 months that have elapsed since then, the industry has achieved commercial importance, supplied immense quantities of materials for pre-war industrial expansion to meet "defense" and Lend-Lease needs, and now has reached such importance that it has come largely under the control of the War Production Board for equitable distribution of its major products among 13 claimant agencies. It is worthy of note, however, that the Bureau of Ships, Navy Department, began exploratory use of fibrous-glass products in 1932, within one year after the date of the first experimental trials of the new process. This early recognition of the military importance of fibrous glass gave impetus to further research work. The foregoing rapid scanning of historical development must be filled in, lest the. impression be created that glass fibers were suddenly created out of thin air, with no antecedent trials, failures, and partial successes. The actual history of glassmaking is lost in antiquity. Probably some nomadic tribesman found molten glass beneath the bed of a hot campfire built upon sand of the proper composition. If his curiosity led him to poke the glowing, viscous pool with a green-wood stick or some handy weapon, it is probable that he drew a glass fiber on the end of his implement. Molten glass has much the same consistency as honey or molasses; it strings out tenuously. Thus, it is quite possible that the first form of glass shaped by man's action was a glass fiber. Artisans in glass, throughout the long Direc- of glassmaking as an art> drew fibers from fine rods for many decorative applications, including "spun glass" decoration in beautiful stemware and the charming millefiori (glass flowers encased in solid glass), and even to create the blood vessels in glass eyes to match a bleary mate.

Jan 1, 1948

By T. B. Counselman

Probably the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of being high in phosphorus because of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetite area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake Superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mines, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion. Range of Minnesota, were hard and lumpy, and opened UP the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium, and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi. and it is these big open-pit deposits that constitute our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The Process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers, and tables, which later were replaced by classifiers. Ore particles finer than 100 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes. The latest and most important process that has been

Jan 1, 1947

By R. P. Aikman, F. G. Miller, J. M. Podgursky

As part of a larger study of the mechanism of froth flotation of coal, the rates at which coal particles of various size and specific gravity react to froth flotation were investigated. Results of this study show that in flotation: I) recovery rate increases, but selectivity decreases with a decrease in particle size down to 100 mesh, and 2) recovery rate is constant for all sizes between 100M and 325M. n response to the growing demand for low-sulfur coking coal for iron making, the coal industry is continually striving to perfect methods for cleaning coal to acceptable ash and sulfur levels while maintaining maximum product yield. By present standards the industry has adequate processes for cleaning coarse coal, i.e., + 28 mesh, at almost any desired specific gravity. However, in the case of fine coal, i.e., —28 mesh, neither of the two existing processes - froth flotation or hydrocycloning — in its present state of development yields products that are comparable in ash and/or sulfur content to products normally obtained from coarse coal processes. The work outlined in this paper is part of a larger study directed toward maximum exploitation of froth flotation for fine coal processing. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of froth flotation with other fine-coal processing methods. The paper includes: 1) A discussion of the value of a detailed wash-ability study as a method of assessing the problems associated with fine coal processing, 2) A general discussion of hydrocyclone principles, included to serve as a basis for understanding the mechanism of coal flotation, and 3) A detailed discussion of the mechanism of coal flotation, as well as the research leading to the optimum use of froth flotation in combination with other fine-coal cleaning methods to provide efficient fine-coal processing. Our study of the rates at which coal particles of various size and specific gravity react to flotation shows that in flotation: 1) recovery rate increases but selectivity decreases with a decrease in particle size down to 100 mesh, 2) recovery rate is constant for all sizes between 100 mesh and 325 mesh, and 3) the flotation process effectively rejects only those extremely fine particles which do not contain surface carbon. (Because of this feature, froth flotation is an excellent method for rejecting clays - the only extreme fines in - 325-mesh coal that are always carbon free.) Washability studies of flotation products are used to assess flotation efficiency. These studies show that: 1) the increase in percent sulfur in flotation products above the theoretical sulfur content as defined by the washability study is due almost entirely to flotation of fine high-specific-gravity particles that are part coal and part pyrite, and 2) in a given size range particle floatability decreases with an increase in particle specific gravity. Error curves are explained and are used to compare the mechanisms of coal flotation and hydrocycloning. These comparisons show that hydrocyclone performance is affected primarily by particle mass, i.e., particle specific gravity and size, whereas coal flotation performance is dependent on both the particle mass and the coal surface available for bubble attachment. Since the error curve is a basic tool for rating the efficiency of any coal processing system, it will be useful to quickly review the principles of error curve construction. RATING COAL-PROCESSING EFFICIENCY BY THE ERROR CURVE The organic component of coal is of lower specific gravity than its impurities, and the most effective principle for coal concentration is therefore separation on the basis of specific gravity. However, since there is no sharp dividing line between pure coal and pure ash components, specific gravity must be closely controlled if the product is to have acceptable quality at maximum yields. In turn, the basis for close control in any coal processing system is the reference standard provided by precise laboratory washability studies. In these studies, coal is carefully separated into a series of progressively higher specific gravity fractions to establish a relationship

Jan 1, 1968

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,' is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3' tests, however, this is not justified, and the D values

Jan 1, 1941

By Nicholas J. Grant, Italo S. Servi

THE creep and stress rupture properties of three grades of aluminum have been reported in a previous paper.' It was found that the stress coefficient of the creep rate and of the rupture time changes at the transition from low temperature-type to high temperature-type deformation. The transition corresponds to the equicohesion for grains and grain boundaries. In order to support the conclusions obtained from the examination of creep and stress rupture data, the deformed specimens were observed metallographically and a few special tests were conducted. The results of these qualitative observations are given in the present paper. Experimental Procedure and Results Table I gives the types of aluminum specimens.' The creep and stress rupture tests were conducted in simple tension at constant stress. Further details on the experimental techniques have been given.' The test bars were electropolished in a perchloric-acetic mixture before testing and were observed after testing without any further preparation unless otherwise specified. Observations of specimen cross-sections were made after electrolytic polishing and etching. The samples were extended along a direction parallel to the longer side of the micrographs of Figs. 12 through 27. The log-log plots of stress vs. minimum creep rate for the three grades of aluminum appear in Figs. 1 and 2. The reference numbers on each curve help relate the photographs to the conditions of testing, indicating where high temperature-type deformation and failure prevailed and where low temperature behavior prevailed. Deformation of Single Crystals at Very High Temperature: An annealed, high purity aluminum specimen was slightly strained at one end and re-annealed. A large single crystal was formed at the strained end of the specimen during re-annealing; the other end remained polycrystalline (see Fig. 3). A stress of 50 psi was applied to the cold specimen to avoid loading at 1100°F. The temperature was then raised to 1100°F, kept at 1100°F for 3 hr, and lowered again to room temperature. Fig. 4 shows the appearance of the specimen after testing. The single crystal deformed by gliding along parallel planes, while the polycrystalline part deformed mainly by grain boundary flow. Some grain growth occurred in the polycrystalline part. Another high purity specimen, which had two large single crystals at the two ends and a polycrystalline zone in the middle portion, was tested at 1000 °F under a stress of 100 psi. The appearance of the sample after test is shown in Fig. 5. Even though considerable slip occurred in the single crystals, the fracture occurred in the weaker polycrystalline portion. Evidence of Grain Boundary Migration during Creep Testing: A high purity, coarse grained specimen, which had a large crystal in the middle portion (see Fig. 6) was tested at 700°F under a constant stress of 175 psi for 30 hr. The appearance of the specimen after testing (Fig. 7) indicates that the large crystal deformed by gliding along parallel planes, while the rest of the specimen deformed mainly by grain boundary flow. Microscopic examination showed clear evidence of grain boundary flow and grain boundary migration, an example of

Jan 1, 1952

By S. R. B. Cooke, H. S. Choi, D. H. Harraway, I. Iwasaki

The mineralogy of natural iron ore samples and their slimes have been investigated and the nature of slime interference in iron ore flotation has been studied. The results have been correlated with the flotation behavior of a natural ore sample. Various conclusions have been reached as a result of these studies. In the flotation of iron oxide ores, desliming is generally considered to be an essential step to successful separation, irrespective of whether the iron oxide or siliceous gangue minerals are to be floated, although some workers have found empirically that certain collectors and reagent combinations are less sensitive to the presence of slime than others. The detrimental effect of slime is considered to be twofold. First, the presence of slime presupposes a high reagent consumption because of high specific surface. When clays are present and when cationic collectors are used abstraction by ionic exchange may augment this condition. Attempts to compensate by the addition of large amounts of reagent result in only partial correction. Second, slime coatings on granular particles tend to interfere with the bubble-mineral contact. The nature of slime coatings in flotation is quite complex and has been the subject of considerable study; an attempt was recently made by Fuerstenau et al.' to relate the slime-coating density with flotation recovery and with the properties of the electrical double layer at the mineral surfaces. Although major constituent minerals in the oxidized iron ores of the Mesabi and Cuyuna ranges are hematite and goethite (limonite) as the iron oxides, and quartz and chert as the siliceous gangue, very little is known of the mineralogy and of the chemical and physical characteristics of the slimes, and still less of the interaction between slimes, collector, and the mineral surfaces. For pragmatic reasons iron ore slimes are defined as — 20p material, based upon the calculated settling velocity of a quartz sphere of the stated diameter, and of all other equal-settling mineral particles. Active slime interference with flotation is usually attributed to particles 5p in size or finer, the extent of such interference appearing to depend not only on the mineralogy but also on the size distribution of each mineral in the slime fraction. The objective of this work was to acquire a more specific knowledge of the constitution of iron ore slimes and of their role in flotation. The mineralogi-cal composition of natural slimes was obtained by differential thernal analysis (hereinafter referred to as DTA), electron microscopy, and chemical and X-ray analyses. Some flotation tests were made on natural ore samples. The surface properties of several constituent minerals were investigated by electrophoretic measurements and by determination of the adsorption of some typical flotation collectors. Finally, simplified flotation tests were made on granular goethite and quartz in the presence of various artifically prepared slimes; the results were compared with laboratory flotation tests made on natural ores. MATERIAL AND METHODS Mineralogy of Some Iron Ore Slimes: Samples of two wash-ore tailing::, hereinafter identified as A* and B, *Sample A of the present investigation 18 the same am ore A in ref. 3. of a wash ore C, and of a paint rock D, all from the Mesabi range, were selected for investigation on the basis of prior information concerning their flotation behavior. The two wash-ore tailings, when deslimed, were known to respond well to flotation, whereas the wash ore was high in goethite, tended to be slimy, and responded poorly to flotation. The paint rock also exhibited sliming tendencies, and was suspected to contain relatively large quantities of clay minerals because of its high A1203 content. Gruner states that the paint rock of the Mesabi frequently contains kaolinite. To ascertain the relative sliming tendencies of each sample a standardized desliming method was employed. All samples were ground through 65 mesh using jaw and rolls crushers. A 500-g sample of each

Jan 1, 1962

By W. C. Coffin

The refractory linings of open-hearth steel furnaces above the bath line are subject to severe wear not only from the heat caused by the combustion of the fuel and the reactions of the bath, but also from the melting action of the gases when not controlled and directed, and from the scouring of the oxides, etc. with which the products of combustion are charged. The framework that encases or binds the furnace is made up primarily of an iron or steel pan in which the furnace proper is built, side and end buckstays, and tie-rods. The expansion and contraction are so great and variable that the bindings may be subjected to severe stresses unless the tie-rods are carefully adjusted in heating up the furnace, but they are most affected by direct heat and usually become deformed from that cause when the lining is worn thin and, sometimes, when sections of the lining fall in and expose some of the framework. A deformed framework displaces the skewback of the roof arch and tends to distort or crush the roof. Bent buckstays deform the front wall, causing the door frames to stand away from the lining so that the gases burn between the lining and the frames, destroying both of them. Frequently the frames are attached to the buckstays; then when the latter bend the frames usually break. Preventing the distortion of the framework and maintaining the economy of the refractories are real factors in the cost of steel making. Nat only does the cost of general repairs and reconstruction add directly to the cost of steel produced, but the time lost in making repairs cuts down the steel production and increases the overhead expense of both the furnace shop and its allied foundry or mills. Many years ago water-cooled equipment applied to iron blast furnaces made it possible to increase greatly not only the size and production of the furnaces but also the life of the lining. It also cut down the loss from frequent repairs. The open-hearth furnace is a much later invention, especially as a commercial factor; for though it dates from the Fred Siemens patent of 1856, much more progress was made in the Bessemer process until the latter eighties and most of the development

Jan 1, 1920

By George G. Binder Jr., James W. Lacey, Arthur L. Draper

An experimental investigation of miscible fluid displacement has been made in linear porous media under highly adverse mobility ratio conditions. Various refined oils were displaced at field rates by liquid propane in both horizontal and vertical models 9 to 36 ft in length. In horizontal tests, mixed zones or transition zones form between the two liquids early in the displace-lents. Initially, the zones grow rapidly. III 2-in. diameter models, the mixed regions become nearly stable zones from 6- to 20-ft long. From then on these quasi-stable zones apparently grow only by molecular diffusion. The lenghts of the quasi-stable zones appear to be almost independent of the core material in which displacement;; are made and increase with increasing rates of injection and oil/solvent viscosity ratios. The lengths of the quasi-stable zones. measured in 2-in. diameter models at viscosity ratios and injection rates anticipated in the field indicate that essentially piston-like displacements of oil by solvent would occur. However, the mixed zone lengths increase markedly as the model diameter increases. In vertical displacements controlled by gravity drainage, only short trans-sition zones form. The entire lenghts of these zones can be accounted for by molecular diffusion. Therefore, in reservoirs having characteristics allowing a high degree of gravity drainage, nearly complete oil recovery should be attainable by miscible fluid displacement. INTRODUCTION The oil industry is faced with an ever increasing cost for finding new oil reservoirs. This, coupled with the fact that conventional methods of oil recovery usually leave from 1 to 3 bbl of oil in the ground for every barrel produced, has aroused considerable interest in developing more efficient methods. An integral part of the mechanism of many of these new methods of recovery is a miscible fluid displacement in which oil is displaced by a much less viscous materiai such as liquid propane. A numher of irlvestigators have explored the mechanics of miscible fluid displace-ment,'.2.1.'."." but in the experiments reported many of the important factors have been varied only over a limited range far removed from norma1 oilfield values. This paper presents the results of an experimental study of oil displacement by liquid propane at field rates from linear, natural-sandstone models of various sizes. Both horizontal and vertical flow tests were made. EXPERIMENTAL APPARATUS AND PROCEDURE Refined oils with viscosities varying over a wide range were displaced at several rates by liquid Propane from both horizontal and vertical flow systems. The behavior of the displacement was observed by propane-oil analyses of the effluent and, when possible, by differential pressure measurements along the cores. A schematic flow diagram of the apParatus used to conduct the experirents is shown in Fig. 1. The cores used in the tests were 9-ft lengths cut from natural consolidated sandstone and turned to the desired diameter. These were cast in steel tubing with a low melting point (160°F) alloy which expands on solidification. Flanges welded to the ends of the steel pipes permitted sealing the ends or butting one core to another. Pressure seals were maintained with O-rings. The cores were cleaned by flushing

By J. T. McGrath, R. C. A. Thurston

Poly crystalline specimens of copper, and copper with various additions of zinc, were tested in plane-bending fatigue. In tests performed at a constant stress, the fatigue life of copper increased slightly with the addition of up to fifteen per cent zinc. There was a sharp increase in fatigue life as further additions of zinc of up to 35 pct were made. Surface observations showed that the coarse slip bands that are characteristic of fatigue became narrower as the concentration of zinc increased. The rate of crack propagation also decreased with increasing zinc content. It is suggested that the fatigue behavior is controlled by cross slip processes. CROSS slip occurs when dislocations move from one primary slip plane to another along a connecting or cross slip plane. The primary and cross slip planes have a common slip direction. Wide stacking faults, having low energy, tend to make cross slip more difficult. According to recent theories, the ability of a material to cross slip is important to the formation and propagation of fatigue cracks. McEvily and Machlin2 have examined this concept experimentally by fatiguing single crys tals of lithium fluoride, sodium chloride, silver chloride, and KRS-5.* The latter two materials ex- hibit easy cross slip, while the former two do not. Normal rapid fatigue failure was obtained in the silver chloride and KRS-5 specimens, whereas it was much more difficult to achieve in sodium chloride and lithium fluoride crystals. Furthermore, numerous slip band extrusions and intrusions were found in silver chloride and KRS-5 crystals, whereas only one isolated extrusion was found in lithium fluoride and none was found in sodium chloride. McEvily and Machlin also consider that there is no clear-cut demarcation between crack initiation and propagation. The intrusion-extrusion process, which initiates crack formation, continues ahead of the cracks to allow propagation of these cracks along slip bands. The process of cross slip is therefore important not only to crack initiation, but also to crack propagation. Holden4 postulates that fatigue crack growth is dependent upon cross slip and thus upon stacking-fault energy. Using an X-ray microbeam technique, he found a cyclic subgrain structure in fatigued aluminum and a-iron. Holden suggests that micro-cracks develop in the densely-packed sub-boundaries ahead of the main crack front, and when sufficiently numerous join up to promote crack growth. The ease with which a subgrain structure could form would depend upon the ability of the dislocations to cross slip, and thus upon the stacking-fault energy. Hence in aluminum, which has a high stack-ing-fault energy and in which cross slip is easy, Holden found that the relative rate of fatigue crack propagation was considerably greater than in stainless steel, a low stacking-fault energy material. It has been shown by a number of investigators that the probability of forming deformation stacking faults in copper increases as zinc is added.5-7 Cross slip should, therefore, become more difficult as the zinc concentration is increased. In order to check the validity of the foregoing theories, it was decided to test copper and copper with various additions of zinc in plane bending fatigue, and determine to what extent their fatigue properties are dependent upon their ability to cross slip. EXPERIMENTAL PROCEDURE Fatigue tests were carried out on polycrystalline OFHC copper and various copper-zinc alloys with 5, 15, 20, 30, and 35 wt pct Zn. The Cu-Zn alloys were obtained commercially in sheet form. Test specimens, as shown in Fig. 1, were machined from sheet that had been reduced to an approximate grain size of 0.040 mm, the heat-treatment procedure being similar to that of Feltham anc copley.8

Jan 1, 1963

By C. R. Fulton

The idea of making permanent magnets by sintering is not a new one, but until the introduction of the iron-nickel-aluminum permanent-magnet alloys there was little need for such a process. Permanent-magnet alloys in use up to the time of this development could be forged and machined to the exact size or shape required without too much difficulty. These new Fe-Ni-A1 alloys, which have become known as Alnico in this country, soon became very popular because of their superior magnetic properties, but when they were made by casting they did have some disadvantages when compared with the older type of permanent-magnet steels. Among these disadvantages were the following: 1. It was almost essential that they be cast to size, since they could not be readily forged or machined. The material could be ground but this was quite expensive, particularly for small magnets in large quantities. 2. The material had a large grain size and was mechanically weak. 3. Close tolerances could not be held and on small magnets this meant grinding almost the entire magnet. Because of the brittle nature of the material, there was considerable loss due to chipping and cracking during these grinding operations. 4. Because of its high aluminum content, the molten alloy had a high surface tension. It was difficult to prevent loss of aluminum by oxidation during the melting operation. In view of these difficulties it is not hard to understand why a process for sintering alnico was developed, or why sintered alnico has come into such widespread use in recent years. It might be well to qualify this by saying that it has come into widespread use for small magnets weighing 2 oz. and less, of the type shown on Fig. I. In this size range, sintered alnico has been able to compete in price with cast alnico. Magnets larger in size, of the type shown on Fig. 2, can be made but they do not compare favorably in price with the cast material. An idea of the range of sizes that have been produced is given by Fig. 3, which shows a small magnet weighing 0.006 oz. and a large magnet with a steel insert weighing 4 lb., both made from sintered alnico. Magnets weighing more than 2 oz., however, should not be made from sintered

Jan 1, 1945

By A. E. Jenkins, A. Jostsons

Isothermal sections of the Ti-0-H phase diagvam at 600°, 700°, and 800°C have been constructed from equilibrium hydrogen pressure measurements over a range of Ti-0-H alloys containing up to 34 at. pct 0. Oxygen reduces the hydrogen solubility at fixed hydrogen pressure but increases the terminal solubility in the a solid solutions at the a/(a + P) phase boundary. Metal-lographic studies of alloys annealed below the eutectoid temperature show that oxygen also increases the ter-ninal solubility of hydrogen in the a solid solution in equilibrium with the hydride phase. The effect of oxygen on hydrogen solubility is discussed in terms of the electronic and geometric structure of interstitial solid solutions. THE isothermal solubility of hydrogen in a Ti-0 alloys at 800°C has been measured by Hepworth and ~chuhmann' who subsequently used ternary Gibbs-Duhem integrations to calculate oxygen activities in binary Ti-0 alloys. The present study aims to extend Hepworth and Schuhmann's measurements to alloys richer in oxygen and to a range of temperatures. This paper presents the results of hydrogen equilibrium pressure/concentration measurements in Ti-0 alloys as well as observations on the effect of oxygen on the terminal solubility of hydrogen in a titanium. The thermodynamic properties of binary Ti-0 alloys, derived from these measurements, will be published separately.' EXPERIMENTAL METHODS Specimen Preparation. Ti-0 alloys were prepared from iodide-refined titanium and titanium dioxide obtained by hydrolysis of redistilled titanium tetrachlo- ride. Specimens containing up to 16 at. pct 0 were prepared by electromagnetic levitation3 whereas a conventional tungsten arc furnace with a water-cooled copper hearth was used to melt oxygen-rich alloys. The specimen homogeneity was indicated by the constancy of lattice parameters of samples from various parts of the ingot as well as by the sharpness of the reflections on X-ray powder patterns. Oxygen-rich specimens in the composition range (20 to 34 at. pct), where ordering has been ~bserved,~ were annealed for 300 hr at 600°C prior to use in hydrogen solubility measurements. Apparatus. The hydrogen pressure/concentration measurements were made with a modified Sieverts apparatus shown diagrammatically in Fig. 1. Specimens were placed in a clear silica tube and impurity pickup by direct reaction with silica was prevented by lining the heated end of the silica tube with thin molybdenum sheet. A double silica tube was required to eliminate loss of hydrogen by diffusion through silica at high temperatures and high hydrogen pressures, the space between the tubes being maintained at a hydrogen pressure equal to that above the specimen. Hydrogen was purified by diffusion through a Ag-Pd tube.= Hydrogen pressures were measured with a mercury McLeod gage in the range 0.001 to 4 Torr

Jan 1, 1968

By P. W. Rainier

The Chivor emerald field is situated on the eastern slope of the Andes in the Department of Boyach, at an elevation of about 8000 ft. above sea level. It overlooks the Llanos (plains) of the Orinoco and is watered by many streams flowing into the Rio Meta, the Orinoco's largest tributary. The Rio Meta is navigable from the Orinoco to a point within about 50 miles of the Chivor district and may eventually prove to be the reasonable outlet for the future development of this part of the country. The topography of the district is extremely rugged and mountainous (Fig. I), the difference in elevation between two points on a mining claim 1 km. square being sometimes as much as 4000 ft. The ground is covered with dense forest growth and the available timber is suitable and sufficient for mining purposes, but it is becoming gradually depleted by Indian clearings as the country around the mines becomes settled. The many streams combined with the rough topography give good possibilities for hydroelectric power. The center of population nearest to Chivor is Bogoth, the capital of the republic and a city of some 300,000 inhabitants; the distance is two and one-half days' travel. The first stage of the journey from BogotB is accomplished by rail to Choconta, some 4 hr. travel. From Choconth the journey is made in the saddle, one night being spent in Guateque. The latter is a small town and the nearest post office to the mines, being some 10 hr. ride distant. The roads are mere bridle paths, in parts hazardous and almost impassable in the wet season. All supplies brought to the mines, other than those produced locally, are carried by pack mule; mule freight from Choconth costs 3 centavos1 per pound. The climate of the Chivor district is healthful and bracing. The wet season begins in March and concludes in November, the remaining months being dry. The annual precipitation is about 130 in. The temperature throughout the year is nearly constant, varying from about 45" F. to about 65" F. shade temperature. The rains are cold and unpleasant, and for the greater part of each day in the wet season the country is shrouded in dense mist. A fire can with comfort be kept burning in a living room all the year round. There are a few slight

Jan 1, 1931

By S. P. Kinney, A. J. Boynton

THIS paper is not the result of recent research with regard to any particular feature of iron metallurgy, blast-furnace practice or mechanical engineering. It is rather a series of notes with regard to contemporaneous progress in blast-furnace construction and operation, together with some suggestions as to changes and improvements that seem to be desirable. On April 1, 1930, a committee of the Chicago District Blast Furnace and Coke Association presented to that association a rather ambitious study of blast-furnace equipment, together with recommendations for the design of construction of a complete blast-furnace unit for the production of 1000 tons of pig iron per day. This report represented the result of months of study by members of the committee, all of whom were actively engaged in operation or design of blast-furnace plants. It is natural, therefore, that comments on the present state of the art should take this 1000-tons furnace, as recommended by the Association, as a basis for comparison with corresponding features of construction or design. See Table 1. In looking through this report at the present time, the significant difference is in the nature of the gas-washing equipment that today would be specified. In other respects, the installation would remain generally very much as it was outlined in 1930. The change in furnace dimensions would be very slight and of no especial significance, except with respect to changes in stock-line diameter, of which more will be said hereafter. The high-efficiency stove as developed by various designers is thoroughly described within this report, and few changes have taken place since. Blowing equipment shows refinement and reflects the improvement in steam engineering. Hoisting and charging equipment and ladles for the conveyance of iron and slag remain, in general, as they were in 1930. In accordance with a general tendency

Jan 1, 1935

By Arthur Fleischer

THE Kalunite process? for the production of metal-grade alumina from alumina-containing ores is applicable, considered from a general point of view, to any aluminous raw material that can be converted to potassium alum or equivalent normal alum. This result of modern technology has been the subject of a continuous study and development since 1929, on a laboratory and test-plant scale, with initial emphasis on the utilization of alunite as the raw material. The research and developmental program was carried out by the Kalunite Company and its successor, Kalunite, Inc., an affiliate of the Olin Corporation of East Alton, Illinois. The process is now approaching the time for a major test in its history with the completion of construction of a plant having a capacity of zoo tons of alumina per day in Salt Lake City for the conversion of Marysvale, Utah, alunite ores to alumina and potassium sulphate. The Salt Lake Alumina Plant is a Defense Plant Corporation project. PRODUCTION OF ALUMINUM The known existence of alunite deposits, especially in the Marysvale district, furnished the motive for the original inquiry into the utilization of this raw material for aluminum production. The deposits in this region were actively explored during World War I and utilized for the production of potassium sulphate, an essential fertilizer, of which a shortage of monumental proportions then existed. Up to the twentieth century for alunite is a mineral with an ancient history-it was used in Europe and in China as a source of potassium alum. It never had been used successfully in. this country as a source of oxide for reduction to metal. Although the known reserves of this ore, which undoubtedly will be greatly expanded with a commercial outlet for this ore, are recognized to be sufficient for only a part of the present-day needs of aluminum, it has a definite place in the aluminum industry. Academically it points the way for future raw materials. The aluminum industry has undergone a remarkable growth in the past few years as a result of defense and war requirements. Its expansion in many ways has been beyond belief and prediction, both in volume and location. This wartime status of the industry has accelerated the consumption of bauxite to such an extent, that a re-evaluation of the raw material reserves for the future peacetime industry and for eventual wartime reserves is seemingly of concern. The generally accepted picture of bauxite ore reserves in the United States, especially in raw material suitable for treatment by the Bayer process, focuses attention on other possible sources of raw material of metal-grade oxide. The perspective for the development of a suitable process may have changed in the interim

Jan 1, 1944

By W. N. Lacey, B. H. Sage

The growing background of experimental information concerning the volumetric and phase behavior of binary and ternary hydrocarbon systems is used as the basis for a comparison of these systems with naturally occurring hydrocarbon mixtures under conditions representative of underground petroleum reservoirs. The qualitative and semiquantitative similarities and differences between the two types of systems are considered in reference to the possibilities and limitations of using experimental data on binary and ternary systems for predicting the volumetric and phase behavior of naturally occurring hydrocarbon mixtures of low molecular weight. The possible influence on such phase behavior of water, hydrogen sulphide, nitrogen, and components of relatively high molecular weight is discussed. INTRODUCTION During the past two decades much effort has been devoted to the study of the volumetric and phase behavior of pure paraffin hydrocarbons and of binary and ternary mixtures of these compounds. Many of these studies were carried out with the direct objective of utilizing a knowledge of the detailed characteristics of binary and ternary mixtures of the lighter paraffin hydrocarbons for predicting the behavior of more complex mixtures. The ability to make such predictions with accuracy would be of great value in petroleum production and refining. Although the behavior of the methane-propane system' served at one time as a qualitative illustration of the probable characteristics of the more complex hydrocarbon mixtures found in nature, it' fell far short of requirements for quantitative predictions. The present paper endeavors to indicate the relation of the more recently accumulated information concerning the behavior of binary and ternary hydrocarbons to this problem. In discussing binary and ternary systems as examples pointing toward the behavior of multi-component systems no effort is made to present new methods of predicting the characteristics of natural hydrocarbon mixtures. Preliminary proposals have been made elsewhere for the prediction of volumetric phase equilibrium and thermodynamic data for multicomponent mixtures, utilizing as a basis the behavior of binary and ternary systems. Numerous other proposals have been made. That based upon the concept of a pseudo-critical state" has proved to be of value to the petroleum industry. Concurrently with this study of binary and ternary systems investigations have been made of natural hydrocarbon systems. Of the many publications reporting such experimental information only a few examples will be mentioned. A number of studies of black oil and natural gas have been made and much attention has been directed to extended and detailed investigations of the behavior of fluids in condensate fieldS 16,17,18,19,20. This work has been supplemented by some studies of the separation of bitumen from natural hydrocarbon liquids The over-all behavior of such systems has been used in predicting the volumetric and phase behavior of naturally occurring mixtures This background of experimental and correlated information concerning the behavior of multicomponent hydrocarbon systems also permits a direct comparison of the characteristics of binary and ternary aliphatic systems with those materials produced from underground reservoirs. PRESENTATION OF DATA The primary limitation encountered in using binary and ternary aliphatic hydrocarbon mixtures as examples of the characteristics of the fluids encountered in underground reservoirs lies in the existing lack of knowledge of the quantitative effect upon behavior of the presence of several important constituents, notably hydrocarbons of high molecular weight, water, carbon dioxide, hydrogen sulphide, and nitrogen. The presence of substantial quantities of hydrocarbons of fairly high molecular weight serves to increase the complexity of the phase behavior of natural systems. No simple systems yet studied give adequate guidance in this regard. The influence of such materials of high molecular weight was indicated earlier",?' to an extent which serves to show that definite limitations now exist in the correlation of simple and complex systems. However, significant progress is being made in filling gaps in the information. For example, similarities in the behavior of fluids in condensate fields with that of binary and ternary systems are becoming more systematically evident. A few studies of the behavior of water in paraffin hydrocarbon systems have been made Results of investigations of mixtures of carbon dioxide and the lighter hydrocarbons also are available Limited work has been reported con-

Jan 1, 1949

By C. W. Phillips, D. N. Frey

A commercial Ti-Fe-Cr alloy, Ti-150, exhibits a martensitic transformation on cooling and two nucleation and growth reactions, one above and one below the Mg-Mf region, on isothermal holding below the single-phase ß temperature range. The reactions were followed by metallographic, X-ray diffraction, and microhardness methods. THE rapidly expanding engineering application of titanium and its alloys makes increasingly urgent an adequate knowledge of the effect of heat treatment on this material. The work herein reported is an attempt to determine certain aspects of the behavior of a commercially available alloy, Ti-150, during heat treatment. The alloy, with a nominal composition of 2.7 pct Cr, 1.3 pct Fe, 0.25 pct 0, 0.02 pct N, and 0.02 pct C, was received in the as-rolled condition as a 3/4 in. round. Slugs 0.11 to 0.12 in. thick were cut under a coolant using a silicon carbide wheel. Preliminary work established that the alloy consists of two phases, a (hexagonal close-packed) and /3 (body-centered cubic), at temperatures below 1750" to 1775"F, and of only /3 phase at higher temperatures. The slugs were heated for 1 hr in air at 1800°F to form a single-phase /3 matrix, then transferred to molten tin (1250° to 1650°F) or lead (1150°F and below) for isothermal holding. Holding temperatures ranged from 700° to 1650°F, times from 0.001 to 23 hr. The treated slugs were then sectioned, one part for metallographic examination and diamond pyramid hardness, the other, after deep etching to remove the high oxygen surface,' for comparative lattice parameter determination and X-ray phase identification. Hardness measurements were taken on the lightly etched surfaces of the metallographic specimens; a 1000 g load on a 136° diamond pyramid was used. Five impressions on each sample were made and the average of the hardness calculated. The use of microhardness measurements to follow the course of an isothermal transformation reaction is undesirable because of the possibility of wide differences in microconstituent hardness.' They were used in this case, however, because of the small amount of material available. At the higher transformation temperatures, where the above-mentioned objection was apparent, the readings were proportioned to correspond to the estimated ratio of transformed and untransformed constituents present. At lower temperatures, resulting in much finer microconstituents, the microhardness measurements were more uniform. The standard deviation of the mean of five impressions calculated from these latter values was 4.2 DPH. Employing 2a limits (probability 0.95) the experimental error of the hardness measurements averages was 8.4 DPH. The etchant used was composed of one part glyc-erol and one part 48 pct hydrofluoric acid." Of a number of etches tried, this one appeared most satisfactory. All micrographs were taken at 500X magnification and with oblique lighting to permit easier identification of the acicular structure resulting from rapid cooling. No advantage was gained by using polarized light for metallographic examination. Phase identification and lattice parameter measurements were made with a North American Philips high angle spectrometer in conjunction with a recording potentiometer. Considerable difficulty was encountered with some of the lattice parameter measurements because of the extreme broadness of the few diffraction lines obtained from samples consisting mainly of strained, untempered, quenched structures.

Jan 1, 1953