Search Documents

By D. I. Bardos, A. M. Bardos, Paul A. Beck

The approximate effective silicon radii in ternary Laves phase alloys with transition elements and silicon were found to range between 1.16 and 1.21A, i.e., considerably smaller than the atomic radius calculated for elemental silicon. The atomic radii were found to increase with the size of the transition element atoms in the structure. It has been noted by Aronsson1 that silicon in solid solution in iron, cobalt, and nickel has an effective CN 12 atomic radius of approximately 1.20Å, a value very much smaller than the CN 12 radius of 1.34Å derived from the interatomic distances in elemental silicon.7 The unusually short metal-silicon interatomic distances in transition element monosilicides and disilicides have been also pointed out by various investigators.1 A similar tendency was observed by Nevitt in Cr3O type silicides.2 Recent work on Laves phases in ternary systems of silicon with transition elements4"8 suggested that extensive Laves phase fields may occur in such systems.8 It has been pointed out by Laves7 that the MgCu2 and MgZn2 type structures lend themselves particularly well for the determination of the effective radii of the component atoms. In these AB2 phases the B atoms are arranged in close packed straight lines, and their distances are related in a simple manner to the lattice parameters.8 The present work was undertaken in order to find out whether or not the B transition element in such AB2 Laves phases can be replaced to an appreciable extent by silicon. In cases where extensive substitution proves to be possible, the "average atomic radius for the B site" at various silicon contents was to be determined, and the effective atomic radius of silicon calculated by extrapolation to complete replacement of the B component by silicon. The following ternary systems were studied: Ti-Mn-Si, Ti-Fe-Si, V-Co-Si, V-Ni-Si, Nb-Fe-Si, Nb-Co-Si, Ta-Fe-Si, Ta-Co-Si, and Mo-Fe-Si. In all of these alloy systems, the Laves phase solid solutions were found to extend over a considerable range of silicon content. As previously reported,4"8 in the V-Co-Si, V-Ni-Si, and Mo-Fe-Si ternary systems Laves phases do occur, even though there are no corresponding binary Laves phases. In stabilizing the Laves phase, silicon acts as if it were decreasing the effective electron concentration of the alloy.8 A more detailed study of the boundaries of the Laves phases in the V-Co-Si and V-Ni-Si systems has been made and will be published elsewhere. In both cases, the elongated Laves phase fields extend parallel to the B-Si side of the composition triangle, clearly showing that silicon is substituting for cobalt, respectively, nickel over a wide range of compositions. The binary Laves phases NbCo2 and TaCo2 have the cubic MgCu2-type structure. It was found that, in both ternary systems with silicon, again the MgZn2-type hexagonal Laves phase is stabilized and that this phase extends to high-silicon contents. In each ternary system at least three Laves phase alloys of the composition A(B1_xSix)2 were used, x here denoting the fractional substitution of the B-transition element atoms by silicon. The alloys, listed in Table I, were prepared by arc melting in argon. Each specimen was water quenched after a homogenizing anneal of 3 days at 110(FC, except for the Mo-Fe-Si alloys, which were annealed at 1200°C. Metallographic examination showed that most of the homogenized alloys consisted of a single phase, although some had minor amounts of a second phase, as shown in Table I. X-ray diffraction patterns were prepared using an asymmetrical focusing camera of large resolution and Fe Ka radiation. The patterns were indexed, and the lattice parameters of the hexagonal Laves phases were determined from the available diffraction lines of highest indices: (213), (205), and (313). The lat-

Jan 1, 1963

By M. Metzger, L. E. Hendrickson

Grain boundary attack in 16 pct HCl was found to be substantially the same at low penetrations in zone-refined aluminum (individual impurities 0.1 at. ppm), superior electrolytically refined aluminum (51 at. ppm), and aluminum with various impurities at much higher levels. It was concluded that impurity atom segregation affecting corrosion would have been detected and that the corrosion susceptibility did not originate in this segregation but in the structure of the boundary. It was pointed out that the significance of most previous studies in this system had been obscured by an unrecognized autocatalytic copper reaction. Although general corrosion rate was also impurity-insensitive , there was shallow pitting attributed to iron seg-regation and a hillocked surface texture associated with copper; these were interpreted as due to cathodic damage affecting- cathode distribution. THE grain boundary corrosion suffered by high-purity aluminum in hydrochloric acid has been the object of some interest (the earlier work is summarized in Ref. 1). The central metallurgical question here is whether the corrosion susceptibility of a boundary originates in its structure or in impurity atom segregation. An attempt to study this question revealed large catalytic effects associated with small quantities of the copper impurity in the aluminum, 220 ppm, or in the corrodent, and these magnified the preferential boundary attack and obscured the intrinsic susceptibility question.' After the catalytic effects had been examined,"' test conditions could be designed to avoid them and methods developed for studying the shallow boundary penetrations prevailing when they were absent.= It then became possible to determine whether intrinsic boundary corrosion in aluminum involves impurity segregation. The older work provided no firm information on grain boundary segregation of specific solutes influencing corrosion although several studies suggested iron segregates.4,5 perryman4 found in 10 pct HC1 that the slowly developing (microns per month) grain boundary grooves were deeper in material of higher iron content (range 10 to 550 ppm, with 5 to 80 pprn Cu) but he did not measure the depths of general corrosion, which were probably several times greater, and his reference surfaces may have varied more than did the groove depths. Metzger and Intrater's results for 20 pct HC~,' which yielded higher time-average rates (mm per month) and deeper penetrations, suggested that boundary segregation of iron (range 4 to 230 ppm, with 22 pprn Cu) decreased the penetration rate. However. in the stronger acid the autocatalytic l.E. HENDRICKSON, Student Member AIME ,and M. METZGER, Member AIME, are Research Assistant and Professor of Physical Metallurgy, respectively, Department of Mining, Metallurgy and Petroleum Engineering, University of Illinois, Urbana, Ill. Manuscript submitted March 11, 1968. IMD effect of the copper impurity is greater1,2 and it is now evident that their corrosion rates had been much magnified by this effect and did not provide a proper basis for the analysis of segregation. In exploratory studies of other solutes (made under the same conditions), 1000 ppm additions of Mg, Mn, or Si or 100 ppm Ca were without effect.1 Montariol6 noted that boundary attack in 22 pct HC1 persisted after zone refining although with fewer deep fissures (ranges 0.06 to 4 ppm Cu, 4 to 23 ppm Fe). Autocatalytic effects may have influenced these results also and those of Perryman.4 The present objective was, as a first step, to see whether quantitative tests designed to exclude autocatalytic influences would indicate the existence of low-level impurity effects on intrinsic boundary corrosion. Comparison of electrolytically refined with zone-refined aluminum of lower copper and iron contents revealed no differences in boundary corrosion, but certain impurity-sensitive differences in general corrosion morphology were noted and investigated further at higher impurity levels. I) EXPERIMENTAL PROCEDURE A) Material. A selection from commercially available material was made with the cooperation of several producers. An electrolytically refined lot (III-A, 1 ppm Cu, 2.4 ppm Fe) studied previously3 provided a starting point. Since material of substantially higher copper content could not be used if the autocatalytic corrosion reaction were to be avoided,2,3 a lot (III-B) of about the same purity was added as a check, two zone-refined lots (I-A and I-B) with copper and iron an order of magnitude lower were selected for comparison, and an intermediate lot (11) was included. Analytical data are given in Table I. For copper in I-B and iron in I-A and I-B, the actual concentration is thought to be near the limit given, i.e., about 0.1 ppm. For titanium, vanadium, and chromium in III-B, the actual amounts are thought to be, like those in III-A, substantially lower than in the zone-refined lots (these elements concentrate in the solid on freezing). Data are given later for some additional lots surveved. B) Specimen Preparation and Procedure. one by 3 cm blanks with a notched stem were cut from 1-mm cold-rolled sheet, annealed 24 hr in air at 650°C, and quenched in an air stream (42°C per sec initial cooling rate, 100 sec to cool to 100°C). The high annealing temperature maximized diffusivities and approach to equilibrium impurity distributions. A water quench, in principle more efficient in preserving the distribution established, was undesirable because the boundaries were almost plane and they tended to shear and migrate during the quench and thus to be separated from any existing impurity atmosphere. Test procedures, previously described,3 involved electropolish-ing, etching 2 min in 10 pct HF at 24.0°C, and expos-

Jan 1, 1969

Jan 1, 1905

By E. R. Johnson

THE copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the western flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past 15 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. FORMER PLANT The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7 1/2 gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by 1-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55 1/2-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73 1/2-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bin serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 1 3/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7 1/2 McCully gyratory crusher set at 1 3/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73 1/2 by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1947

By D. O. Hobson, J. O. Stiegler, C. J. McHargue

The effects of alloy composition, deformation temperature, heal treatment, ad inlerstilial contamination on the occurrence of deformation twins were studied. The twinning transition temperature varied with composition and was a maximuni of 140°C for the 40 pcl V composition. Tire remperature range of the transition was very narrow. Alloys of 20 to 70 pet V could he cold-rolled and exhibited profuse twinning. The alloys which did not twin at room temperature (10, 80, and 90 pel V) could plot be cold-rolled. Oxygen additions systematically lowered the transition temperatures for all vanadium contents. The transition temperature for a 30 pet V alloy increased with annealing temperature, apparently due to changes in dislocation density and configuration. Twinning did not nucleate fracture in any specimen in the 20 to 60 pet V composition range. THERE is great current interest in the refractory metals and alloys as structural materials. An important factor in considering the ductile-brittle behavior of such materials is the role of mechanical twinning as a deformation mechanism. Mechanical twins have been observed after deformation at low temperatures or at high loading rates in the pure metals iron,1 vanadium,2,3 columbium,4,5 tantalum,6 Chromium,7 molybdenum,8 and tungsten.9 Binary alloys in which mechanical twins have been observed include: iron with silicon,10 phosphorous," or aluminum;12 and chromium, molybdenum, or tungsten with rhenium.13-17 The increase in low-temperature ductility obtained by alloying the Group VI-A elements with rhenium is very important with regard to fabricability, and there has been considerable effort to understand the so-called '(rhenium effect". Factors suggested to explain this effect include:'' 1) increase in solubility of interstitial impurities with alloying (electronic effect): 2) changes in the nature of grain boundary phases; 3) changes in interfacial energies of grain boundaries and stacking faults: and 4) promotion of twinning. Although an outstanding characteristic of these alloys is the profuse twinning that accompanies low-temperature deformation, most studies of the rhenium effect have been concerned with the other factors. During recent studies of refractory-metal alloys, it was noted that solid solutions of columbium and vanadium exhibited high hardness and strength at room temperature and elevated temperature and, surprisingly, also showed considerable ductility at room temperature and below. These alloys deformed by twinning at room temperature when subjected to slow loading rates. It appeared that the low-temperature ductility resulted at least in part from the relaxation of stresses by twinning in a system where slip is difficult. The reason for enhanced twinning behavior in some bee solid-solution alloys is unknown. There have been suggestions18,19 that, as in fee alloys, the

Jan 1, 1965

By Arthur Forsyth

A SEARCH through the available literature shows that the cobalt-nickel-silicon system has not been systematically studied. This seems rather odd because all three elements are fairly abundant and have better than average corrosion resistance; however, they have high melting points, which makes experimental work difficult. Cobalt and nickel form a continuous series of solid solutions and each metal dissolves about 7.5 per cent silicon. Many ternary alloys have been studied and the results have been published in a great many different ways, but to present such data in a short but clear and understandable manner is still a problem. The following pages describe the results of the study of 76 alloys from which the partial ternary diagram (Fig. 1) of the cobalt-nickel-silicon system has been drawn. The alloys were chosen according to the plan in Fig. la by taking definite ratios of cobalt and nickel, such as 70 Ni, 30 Co or 40 Ni, 60 Co, and adding silicon in various percentages. Each section was studied in detail by means of thermal analysis and microscopic examination, but only two of these detailed sections were thought necessary in the point perspective drawing to give a comprehensive picture of the liquidus, solidus and solid transformations that take place over the temperature ranges studied. Complete thermal analyses and microscopic data are given in Table 1.

Jan 1, 1940

By E. P. Klier, Taylor Lyman

THE structures formed when austenite is quenched to subcritical temperatures and allowed to transform isothermally have been the subject of intensive study since the work of Davenport and Bain.1 Isothermal transformation diagrams summarizing the results of many of these studies have become widely familiar to metallurgists. Of particular interest to metallographers are the dark-etching, acicular products of transformation formed by isothermal reaction below the temperature of maximum velocity of the austenite to pearlite reaction. These products, the bainite structures, can be formed in a wide variety of steels. However, the constitution of bainite is not well understood and divergent views have been expressed as to its mode of formation. In this investigation a combination of dilatometric, microscopic and X-ray methods has been brought to bear upon the problem in the hope of some elucidation of the bainite reaction as it occurs in hypoeutectoid steels. MECHANISM OF BAINITE FORMATION Davenport and Bain1 considered the mechanism of bainite formation to consist of two steps-an allotropic transformation followed by precipitation of carbide. The separation in time of the two processes was considered to be very slight in the upper temperature range and very marked at temperatures just above the martensite range. This concept has been restated by Vilella, Guellich and Bain2 in the form of a definition of the acicular mode of transformation as: The successive, abrupt formation of flat plates of supersaturated ferrite along certain crystallographic planes of the austenite grains; this supersaturated ferrite begins at once to reject carbide particles, (not lamellae), at a rate depending upon temperature. In effect, this is the acicular mode of transformation, even though the temperature be such as to limit the actual life of the quasi-martensite to millionths of a second. The investigation of isothermal decomposition of austenite in certain alloy steels (notably those containing chromium or molybdenum) has revealed that there may be a range of temperatures between the pearlite and bainite reactions in which the austenite decomposes at a relatively low rate.3-6 Further, it is characteristic that in the second region of fast reaction the decomposition of the austenite is incomplete by one reaction but goes to completion by a second reaction. These observations led Wever7 to a description of the bainite reaction as follows: I. The reaction takes place by initial precipitation of a martensitic intermediate structure. 2. In the upper temperature range this structure readily decomposes into ferrite and cementite. In the lower range carbon separates in an unknown form. 3. In the upper temperature range the precipitated carbide nucleates the precipitation

Jan 1, 1944

By Philip Bucky

THE term "longwall mining" is best known to coal men, although modifications of the method are continually being used in other fields. Longwall mining is of interest today because it makes for greater mecha-nization and better supervision at the working face, and therefore lower production costs and increased safety. It is an approach to the factory system of production, the high efficiency of which as compared to that in mines is well known. There is available an accumulation of experience regarding this work but coordination of experience is lacking and this series of experiments was undertaken to help serve this purpose. Model experiments were used for reasons of safety, cost and time, and because it has been previously shown1,2,3 that a scalar model built of the same material as the prototype will behave in a manner similar to that of the prototype, with time effects the same, if the effective weight of the model is increased in the same proportion as its linear dimensions are decreased. This is accomplished by substituting a centrifugal for the gravitational field; i.e., placing the model in a centrifuge and controlling the strength of the centrifugal field by varying the rate of rotation. Many factors affect the behavior of the geologic material overlying a bed, therefore results and conclusions contained in this paper apply only to the conditions presented herein.

Jan 1, 1938

By Ernest F. Burchard

A Reconnaissance of the manganese- and chrome-ore deposits of Cuba was made by the writer, as a representative of the U. S. Geological Survey, in company with Mr. Albert Burch of the Bureau of Mines, under instructions of the Secretary of the Interior, in the spring of 1918. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the island. The object of the study was to obtain authentic information for use of the United States Government as to the location, character, quantity, and availability of the manganese- and chrome-ore deposits in Cuba. Accordingly, the work comprised examination of such deposits as seemed to be of promise, without regard to stage of development, with a view to a determination of the quantity and quality of ore likely to become available for shipment during 1918 and 1919, and of the tonnage of ore in reserve. Wile it was possible to visit most of the deposits that seemed to be of promise, there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Moreover, the necessity for paying particular attention to the ore deposits and the mines precluded the possibility of making more general studies of the geology of the region, and of making satisfactory collections of country rock and of fossils, and so for other details as to the geography and geology of Cuba the reader is referred to the report by Hayes, Vaughan, and Spencer.l Mr. Burch returned to the United States about 10 days in advance of the writer, who continued, in company with Sr. Montoulieu, investigations of reported deposits in Pinar del Rio, Matanzas, and Santa Clara Provinces. On his arrival in Washington, Mr. Burch submitted to the Director of the Bureau of Mines a summary of the results of the work to date. Later the writer published, as Press Bulietin 190. 380 of the U. S. Geological Survey, a statement concerning the chrome and man-

Jan 1, 1920

By Herbert Clark Hoover, Lou Henry Hoover

PREVIOUSLY I have dealt with the methods of separating silver from copper. There now remains the portion which treats of solidified juices ; and whereas they might be considered as alien to things metallic, nevertheless, the reasons why they should not be separated from it I have explained in the second book. Solidified juices are either prepared from waters in which nature or art has infused them, or they are produced from the liquid juices themselves, or from stony minerals. Sagacious people, at first observing the waters of some lakes to be naturally full of juices which thickened on being dried up by the heat of the sun and thus became solidified juices, drew such waters into other places, or diverted them into low-lying places adjoining hills, so that the heat of the sun should likewise cause them to condense. Subsequently, because they observed that in this wise the solidified juices could be made only in summer, and then not in all countries, but only in hot and temperate regions in which it seldom rains in summer, they boiled them in vessels over a fire until they began to thicken. In this manner, at all times of the year, in all regions, even the coldest, solidified juices could be obtained from solutions of such juices, whether made by nature or by art. Afterward, when they saw juices drip from some roasted stones, they cooked these in pots in order to obtain solidified juices in this wise also. It is worth the trouble to learn the pro- portions and the methods by which these are made. I will therefore began with salt, which is made from water either salty by nature, or by the labour of man, or else from a solution of salt, or from lye, likewise salty. Water which is salty by nature, is condensed and converted into salt in salt-pits by the heat of the sun, or else by the heat of a fire in pans or pts or trenches. That which is made salty by art, is also condensed by fire and changed into salt. There should be as many salt-pits dug as the circumstance of the place permits, but there should not be more made than can be used, although we ought to make as much salt as we can sell. The depth of salt-pits should be moderate, and the bottom should be level, so that all the water is evaporated from the salt by the heat of the sun. The salt-pits should first be encrusted with salt, so that they may not suck up the water. The method of pouring or leading sea-water into salt-pits is very old, and is still in use in many places. The method is not less old, but less common, to pour well-water into salt-pits, as was done in Babylon, for which Pliny is the authority, and in Cappadocia, where they used not only well-water, but also spring-water. In all hot countries salt-water and lake-water are conducted, poured or carried into salt-pits, and, being dried by the heat of the sun, are converted into

Jan 1, 1950

By S. T. Wlodek

The scale md subscale reaction products were identified and their rates of formation were studied in air over the range 1600" to 2000°F (871 " to 1149°C) for periods of up to 400 hr and for hoth the solution-annealed and aged conditions. The effect of prior sltrface preparation on suhscale oxidation was also studied The general oxidation behavior of both Ni-Cr-Mo-Al-Ti type alloys was similar. A surface film of a, Al2O3, forms immediately on exposure Subsequent oxidation continued at a linear rate (QL = 55 * 5 kcal per mole) as colonies of Cr2O3 nucleated at the A12O3/gas interface Further oxidation proceeded at a paraholic rate zvhiclz could he fitted to two successive rate constants. During paraholic oxidation, and depending on temperature, the scale consisted of Cr2O3, NiCr2O4 , and TiO2 with traces of NiO. In the case of Rene 41, the activation energy of both paraholic processes was 66 * 3 kcal per mole suggesting that diffusion of cations tlzrozrgh Cr2O3 was the rate -determining process. An unusual decrease in the oxidation of Udimet 700 at 1900°F where a spinel of Ni(A1,Crh0, zuas the predominant reaction product prevented the accurate assignment of activation energies for this composition. In both alloys internal oxidation of Al2O3 commenced shortly after parabolic scaling was observed. Prolonged exposure prod7tced intemal oxidation of TiN, and in Udimet 700 a complex Mo-Ni nitride was also found. At 1900oF, the subscale reactions in Udimet 700 undergo an inversion which parallels the decrease in surface oxidation; internal oxidation ceases hut is replaced by the formation of "spherodized" 3.' colonies. Surface-preparation techniqtles which introduce appreciable working, such as coarse surface grinding or grit blasting. increase the amount of alloy depletion and internal oxidation in Reni 41. The reverse is true of Udimet 700 for which electropolished or mechanically polished specimens show much more subscale oxidation than strongly worked stirfaces. The strongest commercial nickel-base alloys presently available are generic to the Ni-Cr-Mo-A1-Ti base which exploits the precipitation of Ni3(A1,Ti) as the main strengthening mechanism, while relying on solid-solution strengthening by molybdenum and chromium reinforced by the pre- cipitation of carbides to attain maximum properties. This study characterizes the oxidation behavior of Rene 41, the strongest alloy of the Ni-Cr-A1-Ti type commercially available in sheet form, and Udimet 700, whose higher aluminum and titanium content allows it to exhibit one of the more attractive combinations of high-temperature properties available in a wrought product. The scaling processes of complex, type nickel-base alloys have received relatively little attention. Malamand and vidal as well as Poulignier et al.2'3 have determined the composition gradients across the metal/oxide interface produced by high-temperature oxidation and considered the effect of surface perature, Limited weight-gain data has also been published by Fere 5 for alloys of this type and Radavich6 has identified the reaction products on Udimet 500 and Inco 702 after oxidation at 1832°F. Reference can, of course, be made to the excellent reviews of Kubaschewski and Hopkins7 or Ignatov and Shamgunova8 for a summary of the data available on the oxidation of binary and ternary alloy systems which are related to the more complex alloys considered here. EXPERIMENTAL The analyses of the different commercial heats studied are given in Table I. Using the experimental procedures previously established,9 continuous weight-gain data were obtained on both heats of Rene 41 sheet (A and B) and 150-mil-thick slices of cast Udimet 700. Subscale oxidation reactions were followed by static exposure of cylindrical specimens obtained from swaged Rene 41 (Heat C) and Udimet 700 (Heats E and F). In brief, continuous weight-gain tests were performed on specimens with a surface area of 10 to 12 sq cm. These were abraded through 600 grit Sic paper, electropolished to 2p rms in an electrolyte of 10 pct H2So4 in ethanol, and lightly etched in 10 pct HCl in ethanol before final washing and rinsing in ethanol. All continuous weight-gain data were obtained in dried (-70°F dew point) flowing (1 liter per min) air to an accuracy of +0.1 mg. Subscale oxidation processes were followed by the metallographic examination of 0.5-in-diam by 1.0-in.-long specimens. After an initial center-less grinding, various additional surface treatments were employed to determine the effect of surface preparation on subscale oxidation processes. Before exposure in zirconia crucibles, all samples were lightly etched in 10 pct HCl-ethanol, washed in ethanol, and dried. The depth of internal oxidation was measured to ±0.00025 in. on unetched specimens mounted so as to provide a taper mag-

Jan 1, 1964

By Marius R. Campbell

Does mine-sampling show the commercial value of a coal, and if so, how should it be done? This question is often asked, but seldom answered. During the past summer, while engaged in securing coal for the Government coal-testing plant at St. Louis, I had an excellent opportunity to obtain information on this subject, and the results seem to furnish an answer to the questions propounded above. Sampling for the Geological Survey Coal-Testing Plant. In organizing the work of the testing-plant, it was decided that coal in car-load lots only would be accepted for testing, also that this coal should be loaded under the immediate supervision of a representative of the plant, so as to be certain that the car-load sample would be representative. As an additional check on the work, two mine-samples were to be collected from each mine visited, and these samples, as well as the sam¬ple from the car when it was received at the testing-plant, were to be carefully analyzed at the chemical laboratory, which was established in connection with the plant and operated under the direction of Prof. N. W. Lord, of the Ohio State University, Columbus, Ohio. Mine-Sanmhling:-Mine-samples were collected with great care by me and my assistants, Messrs. J. Shober Burrows, John W. Groves and Frank W. De Wolf. The dominant idea in the regulations which were adopted for mine-sampling was that it should be done in such a manner that the sample would have the same composition as the commercial output of the mine. .

Sep 1, 1905

By E. N. Harshman

Uranium mining and milling are rather new industries in Wyoming and South Dakota, but, in the past 15 years, ore valued at more than $400,000,000 has been mined and milled in the region. The major uranium deposits are in structural and/ or erosional basins or on the flanks of uplifts. The principal host rocks are medium- to coarse-grained sandstones that were deposited in continental or brackish-water environments and were derived in large part from the granitic cores of the uplifts and the sedimentary rocks that flank the cores. The ages of the host rocks range from Cretaceous to Miocene, but more than 95 per cent of the known reserves in the region are in rocks of early Eocene age. The bulk of the ore in the region is unoxidized and lies below the water table; some oxidized ore has been mined in the Powder River Basin and Black Hills districts. The unoxidized ore comprises pyrite, uraninite and/ or coffinite, marcasite, hematite, jordisite(?), and selenium. Minerals in the oxidized ore include hydrous uranium carbonates, phosphates, and sulfates and hydrous uranium and/ or vanadium silicates. The deposits are in the form of ore rolls that contain from a few hundred to a few hundred thousand tons of ore, ranging in grade from 0.1 per cent to 1.0 per cent U3O8. The rolls are at the margins of large tabular bodies of sandstone that has been altered by the orebearing solutions. The deposits are believed to have resulted from the interaction of an alkaline; oxidizing, ore-bearing ground water and a reducing environment. Exploration guides include the spatial relations of ore to altered sandstone, favorable lithology in the host rock, the content of certain elements and/ or compounds in ground water, and the relation of deposits to major paleodrainages.

Jan 1, 1968

By Linney, Robert J.

REPUBLIC Steel Corporation's iron-ore properties in the Adirondacks consist of mines, mills, and sintering plants in the Mineville and Port Henry area and at Lyon Mountain. This article will deal with the properties in the vicinity of Mineville and Port Henry. In 1938, when Republic leased the Mineville- Port Henry operations from the Witherbee Sherman Corp., these properties had just come through some hard depression years. As a result, the mine development program was far behind schedule; most of the equipment needed replacement; and above all, the entire system of mining had to be completely changed to reduce operating costs. The concentrator had been in operation for many years; the process was dry and dusty. Machinery and equipment were either badly worn or entirely obsolete. The sintering plant, also long in operation, was badly in need of repairs.

Jan 1, 1943

By R. D. Begley, A. W. Khair

Introduction The technique being investigated here uses a physical mine model which consists of a plexiglass room-and-pillar model 11.4 x 11.4 cm (4.5 x 4.5 in.). It is placed at the bottom of a larger plexiglass box 25.4 x 30.5cm (10 x 12 in.). The box is then filled with a model material representing geologic overburden. Sand has been selected because of its deformability under gravitational forces. The mine model is capable of creating a cavity and induces movement on the surface of the model material. This surface disturbance can be measured using a photographic technique called holographic interferometry. This paper discusses results of an investigation of the possibility of generating subsidence criteria using physical mine models and laser holographic interferometry. Problem Statement Subsidence appears to be widespread in two states - Pennsylvania and Illinois - although serious subsidence is found in localized areas of numerous other states (HRB Singer Inc., 1977). The US Bureau of Mines estimates that more than 1618 km2 (400,000 acres) of urban areas are threatened by subsidence. Pennsylvania and West Virginia contain 57% of these threatened areas, with the remainder being spread out over 16 states (Johnson and Miller, 1979). Events of subsidence have been reported in urban areas, including Pennsylvania (Gray et al., 1977) and Illinois (Mahar and Marino, 1981). One location has observed three episodes of subsidence beginning in 1950 (Bruhn et al., 1981). These subsidence events all occurred over abandoned room-and-pillar mines. Some mines have been abandoned more than 50 years (Bauer and Hunt,1981) . Available research does not offer much on the problem related to time dependent subsidence, especially those associated with the failure of remnant coal pillars. The physical modeling technique developed at West Virginia University is capable of measuring both instantaneous and time delayed subsidence. Laser Holographic Interferometry Laser holographic interferometry, or holometry, uses the interference properties of laser light to measure small movements of objects. The object requires only optical access and no surface instrumentation. This technique is closely related to photoelasticity. Both techniques rely on the uniqueness of the light reflected off or through an object in any given state of stress. The entire measurement process is done remotely without any surface instrumentation and without using a camera. The interferogram is constructed and visual observation will yield fringes on all areas that yielded or moved. The displacement represented by one fringe was determined by Wilson et al. (1977) and is given by the relationship: [d ='1(1) 2 cos 8 where d = displacement of one fringe 6 = incident angle of laser light A = wavelength of light (632.8 x 10-9 meters for Helium-Neon lasers)] In summary, holometry is capable of detecting very small movements of objects under study. It is a very sensitive process that requires laser light and vibration free experiments. Experimental Program Lab Facilities The primary components of the facilities were the laser and the optical table. The light source was 50 milli-watt, Helium-Neon laser. The optical table was a granite slab weighing nearly one ton. All experiments were performed on the optical table. It consists of a large table sitting on air cells similar to car innertubes. Six air cells were placed on top of two layers of wood and Styrofoam. Figure 1 is a schematic diagram of the vibration free table. Even with these precautions, the experiments still had to be performed at night to reduce potential traffic related vibrations. Room-and-pillar mine models consisting of three different pillar sizes were constructed out of plexiglass. The models were designed to represent three different extraction ratios. Figure 2 shows the models. The extraction ratios were determined by the tributary loading concept (Peng, 1978). These models were the primary component of a seam extraction simulator. A schematic of this simulation device is shown in Fig. 3.

Jan 1, 1986

By M. R. Tek, K. H. Coats, D. L. Katz

A large number of boundary value problems encountcred in unsteady-state heat transfer, fluid flow through porous media, neutron diffusion and mass transfer involve the solution of a linear, parabolic partial differential equation commonly refcrred to as the diffusivity equation, where U is the dependent potential variable. K is the diffusivity (hydraulic, thermal, neutron, etc.) and 1 is the time variablc. Solutions to Eq. I are available in the literature for a wide variety of initial and houndary conditions. The great majority of these solutions are ohtained for geometric boundaries corresponding to linear. cylindrical or spherical flow models. A typical engineering application where the solution to Eq. 1 is required is the calculation of underground water encroachment across the boundaries of oil or natural gas reservoirs, In this particular area of application, the reservoir boundary is invariably approximated by circular geometry. However. the areal shape of many reservoirs can be better approximated by elliptic rather than circular boundaries. Thus the need for a general method of solving the diffusivity equation in elliptic coordinates arises in this problem as well as in other engineering applications involving elliptic boundaries. The solution to the diffusivity equation usually in volves the Error Function for the linear flow model, Bessel functions for the radial flow model and trigonometric or Legendre functions for the spherical flow model. It is well known that the general solution to the diffusivity equation in elliptic coordinates involves Mathieu functions. The significance of Mathieu functions in the analytical treatment of the diffusivity equation in elliptic coordinates is discussed in the literature However, these references do not providc analytical solutions useful in practical engineering problems. The objectives of this papcr are the development of the equations describing the unsteady-state liquid flow through a porous medium with an elliptic inner boun- dary, the development of a numerical method of solving these equations and, finally, a comparison of the water encroachment quantities calculated from the elliptic flow equation with those calculated from the radial flow equation. While the specific problem treated in this paper relates to unsteady-state liquid flow through a porous medium, the basic equations and computational techniques devcloped will apply equally well to problems occurring in the other areas of engincering interest mentioned previously. The solution given here is limited to a single case in which thc outer boundary encloses an area 100 times that of the inner boundary. DESCRIPTION OF THE FLOW MODEL Fig. 1 shows the flow model upon which the calcu lations presented in this paper are based. The inncr and outer houndaries of the flow model are represented by two confocal ellipses with major and minor axes, respectively, equal to 2a1, 2b1, and 2a, and 26,. The height of the elliptic cylinder flow model is denoted by 17. The following assumptions are employed in the development 01 the equations governing the unsteady-state liquid flow through the described flow model. 1. Uniform porosity and permeability throughout the flow model

By J. P. Smith

DURING the winter of 1946 to 1947 potash operations in Germany, France and Spain were visited by the author. The U. S. Department of Commerce, through its Field Intelligence Agency Technical, sponsored the inspection of German properties by representatives of the American Potash Industry. Vast deposits of potash salts occur in the above-mentioned countries, and the production and marketing of these salts are important in their respective economies. Germany An area of some ten thousand square miles of north central Germany is underlain by lenses of potash salts interbedded with greater thicknesses of sodium chloride or common salt. These salt measures are relict deposits from the evaporation of an arm of the Zechstein (Permian) Sea which formerly covered northern Europe. During the peak year of 1940, Germany produced salts containing 1,860,000 tons of K,O and, next to coal, potash is its most important mineral raw material. The German deposits are found in the synclinal areas flanking the Flechtingen, Hartz Mountain and Thuringian uplifts, and, to the north they lie beneath the plains of Hannover. The regional dip of the salt measures is to the north, hence, lenses of potash found at depths of 500 to 1000 m* in the Two general depositional provinces of potash concentrations are recognized: (1) the main basin, and (2) the subsidiary basin. The main basin embraces the producing districts of Stassfurt, Sud Hartz, Halle, and Hannover-Braunschweig. From J. P. SMITH, Member AIME, is Clzief Geologist, U. S. Potash Co., Carlsbad, New Mexico. New York Meeting, February 1948. TP 2621 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 26, 1948. 40 to 45 pct of the German production comes from this basin. The Werra-Fulda district, producer of 50 pct or more of the German potash, lies in the subsidiary basin. Salt Stratigraphy: Five commercial potash zones or beds are recognized. The three beds present in the main basin are: The Stassfurt bed that occurs near the top of the older salt, and the Ronnenberg and Riedel beds in the younger salt occurring 200 to 300 m, respectively, above the Stassfurt bed. The Stassfurt bed is found over the entire main basin, while the Ronnenberg and Riedel are restricted to the Hannover area. Two potash beds occur in the Werra basin. These are the Thuringian, or lower bed and the Hessen or upper potash bed that occurs 60 m above. These beds lie 210 and 150 m, respectively, below the position of the Stassfurt bed, and are restricted to the Werra basin. The upper bed is 2.5 to 11.5 m in thickness, and the principal ores are hartsalz with varying thicknesses of carnallite. The lower bed averages 3 m in thickness, and contains hartsalz. The upper bed is presently being mined, and the

Jan 1, 1951

By J. P. Smith

DURING the winter of 1946 to 1947 potash operations in Germany, France and Spain were visited by the author. The U. S. Department of Commerce, through its Field Intelligence Agency Technical, sponsored the inspection of German properties by representatives of the American Potash Industry. Vast deposits of potash salts occur in the above-mentioned countries, and the production and marketing of these salts are important in their respective economies. Germany An area of some ten thousand square miles of north central Germany is underlain by lenses of potash salts interbedded with greater thicknesses of sodium chloride or common salt. These salt measures are relict deposits from the evaporation of an arm of the Zechstein (Permian) Sea which formerly covered northern Europe. During the peak year of 1940, Germany produced salts containing 1,860,000 tons of K,O and, next to coal, potash is its most important mineral raw material. The German deposits are found in the synclinal areas flanking the Flechtingen, Hartz Mountain and Thuringian uplifts, and, to the north they lie beneath the plains of Hannover. The regional dip of the salt measures is to the north, hence, lenses of potash found at depths of 500 to 1000 m* in the Two general depositional provinces of potash concentrations are recognized: (1) the main basin, and (2) the subsidiary basin. The main basin embraces the producing districts of Stassfurt, Sud Hartz, Halle, and Hannover-Braunschweig. From J. P. SMITH, Member AIME, is Clzief Geologist, U. S. Potash Co., Carlsbad, New Mexico. New York Meeting, February 1948. TP 2621 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 26, 1948. 40 to 45 pct of the German production comes from this basin. The Werra-Fulda district, producer of 50 pct or more of the German potash, lies in the subsidiary basin. Salt Stratigraphy: Five commercial potash zones or beds are recognized. The three beds present in the main basin are: The Stassfurt bed that occurs near the top of the older salt, and the Ronnenberg and Riedel beds in the younger salt occurring 200 to 300 m, respectively, above the Stassfurt bed. The Stassfurt bed is found over the entire main basin, while the Ronnenberg and Riedel are restricted to the Hannover area. Two potash beds occur in the Werra basin. These are the Thuringian, or lower bed and the Hessen or upper potash bed that occurs 60 m above. These beds lie 210 and 150 m, respectively, below the position of the Stassfurt bed, and are restricted to the Werra basin. The upper bed is 2.5 to 11.5 m in thickness, and the principal ores are hartsalz with varying thicknesses of carnallite. The lower bed averages 3 m in thickness, and contains hartsalz. The upper bed is presently being mined, and the

Jan 1, 1951

By Charles Wert

THE diffusion and precipitation of carbon and nitrogen in a iron have previously been investigated using the internal friction as a measuring tool.' Most of this work has been done on rather pure iron; no effect was observed which would indicate that either of these phenomena is affected by the rather small amounts of impurity found in these samples of iron. Fastz observed, however, that both the diffusion rate and the aging properties of nitrogen in iron were sensibly changed by the addition of Vz pet Mn. The diffusion rate at a given temperature is reduced and the nucleation of nitrides is apparently changed somewhat. He observed no such changes for carbon in this alloy. Later Dijkstra and Sladek" extended these observations on nitrogen to other alloys of iron. They found that metals other than manganese also influence the behavior of nitrogen in iron; chromium, molybdenum and especially vanadium affect the diffusion and precipitation of nitrogen even more than manganese does. Their results have been verified in all essential details by this author, who finds in addition that small additions of nickel have about the same effect on the diffusion of nitrogen as the same amount of manganese. The present work was undertaken to study the effect on carbon in iron of these alloying elements. The alloys used had two sources. The material used as a "standard" (designated Fe in this paper) in the measurements was some iron supplied by J. K. Stanley, of Westinghouse Electric Corp., who reported 0.01 pct 0, as the only major impurity. He also made up an alloy of 0.26 pct Ni and one of 0.9 pct Mo using this same iron as a base. They were supplied by him in 2 lb billets, which were sawed into rods and cold formed into 0.030 in. wires for measurement. The alloys of chromium, manganese, and vanadium were prepared by the metallurgy section of the Institute for the Study of Metals, University of Chicago, by adding these metals in turn to vacuum melts of National Research Corp. iron. The small castings prepared in this way were also cold formed into 0.030 in. wires. After these wires had been prepared they were decarburized for 30 min at 730°C in wet Hz. After this treatment, no trace of carbon (as measured by internal friction) could be found. All specimens were then carburized for about 15 min at 710°C and water quenched. By this treatment the internal friction at 40°C was raised to a Q-' ~ 0.015. The diffusion of carbon in these alloys was studied by observing the shape and position of the internal friction peak at 0.9 cycles per sec. These measurements were made using a torsional pendulum in a manner described earlier.' The data are plotted in Fig. 1. It is seen that there is no apparent difference in internal friction between the various alloys. This is in marked distinction to the broadening and shift-

Jan 1, 1953

By Clarence E. Sims

An effort has been made to give both a comprehensive and simplified picture of the origin, modes of formation, and characteristics of nonmetallic inclusions in steel. Exogenous inclusions, those formed by mechanical entrainment or heterogeneous reaction, have their principal source in ladle refractories. Mechanical emulsion is not considered a likely mechanism. Endogenous inclusions, resulting from homogeneous reactions, are formed mainly during cooling and freezing. They are principally oxides and sulfides but include some nitrides and carbides. Deoxidation affects both the quantity and character of such oxide inclusions and significantly affects the size and shape of sulfides. The importance of inclusions is largely in their effect on mechanical properties. It is fitting and proper that we should honor the memory of those technical giants who have left such a rich heritage to our profession. Today, according to annual custom, we pay tribute to such a man. To have been chosen to play a part in this observance prompts in me an inordinate pride while I am humble before the responsibilities of my task. The ranks are growing thin of those who had the good fortune to come under the personal influence of Professor Howe, but the number who continue to benefit from his legacy of technical wisdom con-stantly increases. I am among the latter. One has only to read his works to appreciate his unusual ability to take data and observations from many sources and give them a clear and comprehensive

Jan 1, 1960