Search Documents

By E. S. Machlin, Morris Cohen

GRENINGER and Troiano' were the first to establish the fact that the habit planes of mar-tensitic products are usually planes of high indices. In steels containing 0.55 to 1.4 pct C, the habit plane indices are {225}A.* In steels with more than 1.5 pct C and in Fe-Ni alloys, the indices are {259In. The presence of both habits in certain alloy steels has been reported recently." Several investigators"-" have subsequently attempted to provide an understanding of these complex habit relations. Bowles'6 work is the most recent and the most successful. Like Greninger and Troiano, Bowles concluded that the transformation occurs in two steps, the first, a strain (or displacement) that is homogeneous throughout the volume of the martensitic plate, while the second is a strain that is homogeneous only within relatively small portions of the martensitic plate. The first strain yields the measured tilt of the specimen surface, but does not produce the final martensitic structure. This and the correct lattice orientations are achieved by the second strain. Bowles also reasoned that each strain could be described by the motion of a plane of no rotation and no distortion (hereinafter called the invariant plane) in a direction not necessarily contained in the plane.** In applying these considerations to steels with {225}a habits, Bowles found that the habit plane coincided with the invariant plane of the first strain, a result which signified that the atoms move along certain paths during the transformation. Whether this correlation results from the existence of some sort of a plate nucleus6 lying along the invariant plane of the first strain, or whether the invariant plane primarily defines the preferred directions of propagation of the first strain, will be discussed in a later section. There are two obstacles to the general acceptance of Bowles' treatment: 1—it has not been shown that elements of his double-strain analysis are unique, and 2—it is not known whether his treatment applies to transformations yielding the {2591A habit. Unless these two questions are resolved, the correlation between the habit and invariant planes in the {225}A systems might be regarded as coincidental. Experimental Procedure Using a 70 pct Fe-30 pct Ni alloy as an example of a {2591A habit system, preliminary attempts were made to obtain a double-strain solution based on a Nishiyamax** set of orientation relations and on a Greninger-Troianot set, adopting the stereographic technique described by Bowles" who used the Kurd-jumow-Sachstt set in connection with the {225}A habit. These attempts were unsuccessful because the method is essentially one of trial and error and requires either exceedingly good luck or a prior knowledge of the results being sought. Consequently it was decided to measure independently the strain associated with the formation of a martensitic plate as well as the habit-plane indices of the particular plate. By means of matrix algebra, the measured strain was applied to the austenite lattice, whose orientation with respect to the strain was determined, in order to ascertain whether the resultant structure would have the lattice of martensite. This was not found to be the case, and hence it was assumed that the measured strain was the first of two Bowles-type strains, characterized by the motion of an invariant plane. A solution of this displacement was obtained in terms of the invariant-plane indices and the direction of motion of the atoms. Then the second strain

Jan 1, 1952

By G. M. Schwartz, G. A. Thiel

Dimension stone was first quarried in Minnesota in 1820 and a very active industry has grown up over the years. The main basis of the present industry is a wide variety of igneous rocks sold under the general trade name of "granite." Also of considerable importance is the Ordovician dolomite sold under the locality names, Man kato, Kasota and Winona. THE first record of the quarrying of dimension stone in Minnesota dates back to 1820 when limestone was quarried locally for part of old Fort Snel-ling. Limestone quarries were operated at Stillwater, Mankato, and Winona as early as 1854. Granite was quarried first at St. Cloud in 1868, and within a few years thousands of tons were shipped to widespread points. Rough dimension stone for large buildings furnished the first important market, but beginning in 1886 paving blocks were in demand. The largest shipment was in 1888, when 1925 cars were shipped from the St. Cloud area. Quartzite was quarried first at New Ulm in 1859 and somewhat later at Pipe-stone and elsewhere in southwestern Minnesota. The productive dolomite quarries at Kasota were opened first in 1868 and have continued as large producers of a variety of stone to the present time. At present, the industry is controlled by relatively few operators, and for that reason detailed figures on dimension stone are not released for publication. A general idea may be obtained from the data in the Minerals Yearbook for 1948. The figures for total stone produced in Minnesota are 1,804,000 tons valued at $5,090,652. Probably the largest item in the latter figure is received from dimension stone. A better idea of the situation in relation to the country as a whole may be gained by using the data for 1930 when more companies were operating in Minnesota, and complete figures were published. In that year Minnesota produced granite valued at $2,668,119 and ranked third among the states in value. Minnesota's production of granite was almost exclusively for dimension stone. In the same year Minnesota produced 300,000 tons of limestone (dolomite) valued at $840,860, and this likewise was mainly dimension stone. In finished limestone Minnesota ranked second among the states in 1930. Sandstone and minor amounts of quartzite are the only other dimension stones that have been produced in Minnesota, but the quarries are now inactive. The commercial stones of Minnesota have been described in two reports by Bowlesl and by Thiel and Dutton. The early history of quarrying in Minnesota and extensive notes on the various rocks are given by N. H. Winchell.8 Small limestone and dolomite quarries were numerous throughout the area of Paleozoic rocks in southeastern Minnesota. Early production was largely dimension stone. With the increased use of Portland cement, most of these ceased production, and today only those at Kasota and Winona remain in operation. In recent years many quarries have reopened and new ones started, but these are devoted to the production of crushed rock and agricultural lime. As the application of modern quarrying and finishing methods increased, small companies in the granite business have dropped out, and the remaining companies have modernized their plants, purchased old quarries, and opened up new ones, thus furnishing a wide variety of granites suitable for most of the customary uses. It is the purpose of this review to present notes on the geology and operations of each of the quarries now operating within the state. Granites and Related Igneous Rocks The term granite as used in this report includes granites, gneisses, diorites, gabbros, and other igneous rocks. The granites of greatest economic importance are found in three widely separated regions, see Fig. 1. 1—Central Minnesota in the region of the city of St. Cloud, 2—the upper Minnesota River valley region, 3—the northeastern portion of the state, commonly referred to as the Arrowhead region. The St. Cloud Region: The rocks of the St. Cloud region are mainly granites and related rock types such as monzonites and quartz diorites. The stones may be grouped into three major types, namely, pink granite, red granite and gray granite. Most of the pink granite occurs in the area to the southwest of St. Cloud. The rock is best described as stone with large pink crystals set in a finer grained black and white background. The minerals of the matrix occur in remarkably uniform sizes, and the pink crystals are sufficiently uniform in their dis-

Jan 1, 1953

By M. E. Nicholson

The effect of boron on the austenitic transformation rate of iron is smaller than on low carbon steels. The influence of austenitizing temperature on B-Fe is the reverse of its influence on steels. THERE have been many studies made of the influence of boron on the hardenability of steel, but apparently none has been made of its influence on the y-a transformation of pure iron. There are several facts suggesting that boron should have a pronounced effect on the transformation rate of iron. First, Simcoe et a1.l indicated that boron reduces the nucleation rate of ferrite and bainite. Second, they showed, along with others,', " that the lower the carbon content of steel the greater the influence of boron on hardenability. If this trend extends to pure iron, the influence on rate of ferrite formation should be considerably greater for iron than for medium carbon steels. According to Rahrer and Armstrong," the multiplying factor for boron in pure iron should be about 2.40, compared with 1.50 in a 0.35 pet C steel. According to an extrapolation made by Grange and Mitchell,' the effect should be even greater, and the multiplying factor should be about 3.5 in iron. Many investigations of the boron influence'.7, 2, 5 indicated that boron is effective only when in solid solution. On the other hand, Chandler and Bredig" suggested that boron increases hardenability by combining with nitrogen, thereby preventing formation of AlN, which catalyzes the decomposition of austenite. If their hypothesis is valid, boron should have no effect on an alloy free from nitrogen. Digges et al." showed that so far as low nitrogen high purity Fe-C alloys are concerned this is not the case. No experiments, however, have been made on low nitrogen iron. To determine whether or not boron has an effect on low nitrogen iron and, if an effect exists, to determine whether it is as large as predicted from the investigations of boron treated steels, the following work was performed. Because of the rapidity with which iron transforms from austenite to ferrite at even a moderate degree of supercooling, it was decided to study the influence of boron on the transformation rate of iron by determining the effect of quenching rate on the temperature of the beginning of transformation. The technique, essentially that used by Greninger' and Duwez,H consisted of heating small specimens, 0.1 in. sq and 0.010 in. thick, in an atmosphere of purified helium with a resistance heater coil, and then quenching the sample in a jet of helium gas. At the time the jet was applied, the heating coil was removed from around the sample. The sample was suspended in the furnace on 30 gage chrome1 and alumel wires, one welded to each side of the specimen, which also served as a thermocouple for measuring the specimen temperature. Specimens were prepared from vacuum-melted iron obtained from the National Research Corp. which was rolled to a thickness of 0.060 in. and then decarburized in wet hydrogen for 51/2 hr at 700°C. This treatment also removed any boron present in the iron. The resulting iron contained 0.001 pet C. 0.0002 pet N, and 0.005 pet 0. One half of the piece was then boronized by surrounding it with 325 mesh boron powder and heating it for about 2 hr at 900°C in H,. The boronized iron was then homogenized at 1100°C for 24 hr. The iron boride case formed by boronizing was removed by grinding 0.010 in. from each side of the plate, and the piece was finally rolled to a thickness of 0.010 in. The resulting alloy contained

Jan 1, 1957

By P. Somasundaran

Flotation of minerals has usually been discussed in terms of solid-liquid interfacial phenomena. This paper discusses the relative importance of phenomena such as collector adsorption at other interfaces formed between the bubble, liquid and solid. Adsorption of collector ions of various chain lengths at liquid-gas and solid-gas interfaces has been obtained. The data have been analyzed under conditions corresponding to those of flotation to show the significant role of collector adsorbed on the bubble surface in determining the bubble-mineral attachment required for flotation, and consequently to suggest consideration of this role in the development of better flotation conditions. Vacuum flotation of quartz with alkyl ammonium acetate reported in the foregoing paper1 showed that the collector chain length has an effect on flotation even at concentrations below those necessary for hemi-micelle association of the hydrocarbon chains at a solid-liquid interface. This chain length effect might be explained by the following arguments: Hydrocarbon chains find it energetically favorable to be in a medium of low dielectric constant. Considering the possibility of an iceberg structure at the solid-liquid interface, such a structure would produce a region of lower dielectric constant at the solid-liquid interface than in the liquid phase, because the dielectric constant of ice is 2 to 3,2 while that of water is 80. Depending on chain length, this difference will certainly cause even individual ions to adsorb in higher quantities at the solid-liquid interface. Another mechanism to consider is the possible formation of dimers, trimers, etc and chain length would influence this formation. But, above all, the chain length effect on flotation at concentrations of low adsorption at the solid-liquid interface could be due to the significant but often-neglected role of the collector adsorption at the bub- ble surface. Collector ions or molecules are adsorbed both at the solid-liquid interface and the liquid-gas interface. Below the concentration for hemi-micelle association at the Stern plane adjacent to the surface, the bulk of the collector ions adsorbed at the solid-liquid interface are in the diffuse part of the double layer. If such systems, where there is a gas bubble coming in contact with the solid surface, are to achieve some degree of electroneutrality, those collector ions would have to migrate from the diffuse part of the double layer to the region directly adjacent to the surface during the induction period when the bubble is making contact with the solid. The time necessary for this migration would contribute to the induction period required for creation of the solid-gas interface. It seems reasonable that the induction period could be reduced sufficiently for flotation to occur if these collector ions were carried to the surface by the bubble. In an attempt to ascertain whether or not the bubble could possibly have sufficient collector ions at its surface to meet the requirement mentioned above, the adsorption density of the collector ions at the liquid-air interface was determined. For this purpose, the surface tension of alkyl ammonium acetate solutions was determined as a function of concentration. Adsorption densities of the collector at the liquid-gas interface were calculated using the Gibbs adsorption equation: where y is the interfacial tension and ri and pi are the adsorption density and the chemical potential, respectively, of the chemical species, i. Using the convention that the adsorption density of water at the interface is zero, the following relationship is obtained for the liquid-gas interface where lg refers to liquid-gas interface and RA+ refers to the alkyl ammonium ions. For dilute solutions, rf^-wri^&rfwW [3] where C is the concentration of the collector ions in solution. l?:: can now be evaluated using Eq. 3 and surface tension measurements.

Jan 1, 1969

By Klaus Schwerdtfeger

The rate of formation of silicon monoxide from silica spheres has been measured at 1500°C in H2, H2-H2O, H2-He, H2-Ar, and CO-CO2 gas mixtures. Indications are that in the hydrogen-containing gases the reaction rate is mainly determined by convective diffz~sion. In the CO-CO2 mixtures the rate approches a constant value which is independent of sphere diometer (and gas velocity). This suggests that a surface reaction becomes rate controlling in CO-CO2 gas. WHENEVER silica is exposed at elevated temperature to a strongly reducing atmosphere there occurs, inevitably, a volatilization of silica by the formation of gaseous silicon monoxide. Because of the importance of this reaction in metallurgical processes and laboratory experiments, its kinetics were studied in the present work. EXPERIMENTAL The spheres made of vitreous silica were suspended by a molybdenum wire in the hot zone of a gas-tight high-purity recrystallized alumina furnace tube of 3.1 cm internal diam and 100 cm length. Molybdenum wire resistance heating was used. A purified H2, H2-H2O, H2-He, H2-Ar, or CO-CO2 gas mixture was passed through the tube, from top to bottom. The amount of silicon monoxide formed was determined by weighing the silica balls before and after the experiments. The silica balls were made from commercially available translucent fused quartz glass. In experiments with hydrogen-containing gases the silica stayed vitreous during the experiment, whereas in experiments with CO-CO2 mixtures, which were performed over longer times, the balls were always crystallized to cristobalite (as determined by X-ray examination) at the surface. Constant-pressure head capillary flowmeters were used to control the composition of H2-He, H2-Ar, and CO-CO2 gas mixtures. The oxygen and water vapor were removed from the gases containing hydrogen by passage through columns containing platinized asbestos (450°C) and an-hydrone. The CO was purified from O2 and CO2 by passing it through activated copper (200°C) and through ascarite. The H2-H2O gas mixtures were prepared by passing purified Hz through a mixture of oxalic acid dihydrate and anhydrous oxalic acid held at a constant temperature in a water bath. The equilibrium water vapor pressures of oxalic acid dihydrate-anhydrous oxalic acid mixtures were taken from the available data.1 The furnace system was checked for sufficient gas tightness at regular intervals. As an additional check, the H2O and CO2 contents were measured in the exit gas and were found to agree closely with the metered contents when H2-H2O or CO-CO2 mixtures were used. When purified H2 was used, H2O pressures found in the exit gas were always below 0.1 mm Hg. These contents originate either from an incomplete reoxidation of silicon monoxide in the cold part of the furnace or from small leaks which cannot be avoided. If the latter is the case, such small uncontrolled H2O contents decrease the partial pressure of SiO in equilibrium with SiO2 by less than about 7 pct, which is considered small in comparison to other experimental uncertainties. The temperature of the furnace was controlled automatically in the usual manner. The reported temperature was measured with a Pl-Pt/l0pct Rh thermocouple and was accurate to ± 5°C. TRANSPORT-CONTROL LED RATE OF REDUCTION The gaseous convective diffusion from the surface of a sphere can be predicted from the semiempirical relationship obtained by Ranz and Marshall2 in a study of the evaporation of water and benzene drops in air. The following equation applies:

Jan 1, 1967

By Richard G. Warren, Michael M. Minor, Gayle J. Thomas

INTRODUCTION Los Alamos Scientific Laboratory (LASL) initiated its effort in the Hydrogeochemical and Stream Sediment Reconnaissance (HSSR), a part of the Department of Energy (DOE) National Uranium Resource Evaluation (NURE) program, in late 1975. Since that time, LASL has completed sampling of the Rocky Mountain states of New Mexico, Colorado, Wyoming, and Montana at a density of about one water or waterborne sediment sample per 10 km2 and has sampled about 85% of Alaska at a density of at least one per 25 km2. Analytical results for these samples are reported by National Topographic Map Series (NTMS) quadrangle. All collection and analytical procedures have been standardized from the outset (Sharp, 1977; Sharp and Aamodt, 1978). Until early 1979, only uranium results were reported for these samples; thereafter, results include analyses for at least 42 additional elements in the sediment samples. Each LASL HSSR report also includes a discussion of the relationship of these analytical data to known or possible uranium resources; more recently, these data have been re- examined for their relationship to resources for other metals (Beyth et al., 1980; 1980a). Analytical results for LASL HSSR sediment samples are both comprehensive, including 43 elements, and precise, allowing close inter-comparison of data between quadrangles. A recent HSSR study shows that elemental concentrations in sediment samples from the Dixon Entrance quadrangle in Alaska are insensitive to the choice of sieve size fraction and do not vary significantly between stream locations a few meters apart, except for extremely high elemental concentrations (Warren, et al., 1980). Elements that are particularly reproducible include thorium, hafnium, and the .ram earth elements. Fortunately, sensitivities for these elements, which are often associated with uranium, are excellent by the nondestructive analytical technique of neutron activation analysis that LASL employs. Wet chemical techniques may not always give reliable results for these elements in sediment samples due to the difficulty of dissolving the resistate mineral phases that normally contain these elements. LASL has recently open-filed results for a large number of NTK3 quadrangles; to date analyses have been reported for about 605 of the quadrangles within the states of the Rocky Mountain region. As a result, uranium analyses am now complete for all sediment samples collected from the state of Wyoming. We have chosen to sumnarize the analytical results for Wyoming and portions of adjoining states hereafter termed "the ~ Wyoming regionn (Fig. 1 ) ; nearly 24 000 uranium analyses and nearly 17 000 analyses for 42 additional elements are available for sediment samples collected from this area. The DOE open-file report numbers are shown in Fig. 1 for reports open filed before September 1, 1980. The Wyoming region provides an ideal area for an examination of regional geochemical patterns ex- hibited by sediment samples. It is endowed with a variety of exposed geologic units and with widely distributed uranium districts associated with host units of several ages. However, discussion will focus on rock units of Eocene and Precambrian ages because they are widely exposed and host the majority of the uranium resources within the region (Fig. 2). Miocene units are also widespread and host mineralization in the Brown's Park Formation (Fig. 2). Epigenetic uranium mineralization occurs in sand- stones of lower Eocene age such as the Wasatch, Battle Springs, and Wind River Formations whereas vein type mineralization occurs in Precambrian crystalline rocks. Precambrian rocks within the region consist of a variety of granitic and meta- morphic rocks with l .4-2.8 billion year ages, except within the Uinta Arch, where they consist of a sequence of very low grade metamorphosed or unmetamorphosed 1.0 billion year old sedimentary rocks. Precambrian rocks have served as sources for much of the clastic material comprising the lower Eocene units, and may also have provided the source for the uranium in mineralized Eocene or Miocene sandstones (Stuckless, 1979). The remainder of this paper describes the relationship of elemental concentrations in HSSR sediment samples to exposures of Eocene and Precambrian rocks. The results are used primarily to determine where these Precambrian rocks might provide the most suitable uranium source areas and to infer the direction of transport toward adjacent depositional basins during the Eocene.

Jan 1, 1980

By N. De Nevers

A calculation method has been developed for carbonated water flooding. This method takes into account the effects of oil viscosity reduction and oil swelling, due to carbon dioxide transferred to the reservoir oil from the carbonated flood water. It shows the effect of changes in carbonation pressure and carbonated water slug size. The method is based on a Buckley-Leverett-type linear flow model. The mathematical approach is similar to that developed by Welge, et al, for enriched gas drives. However, it contains a very important advance over the previous papers in its solution to the problem of injection of a "slug" of carbonated water rather than continuous injection of fluid of constant composition. The method also shows the chromatographic nature of the transport of Co 2 in a carbonated water flood. Sample calculations indicate that viscosity reduction is the most important source of incremental oil recovery. Swelling contributes to a lesser extent. Raising the carbonation pressure increases recovery, but this effect diminishes as pressure is increased. increasing the slug size also increases recovery, but again this effect diminishes as slug size is increased. INTRODUCTION In recent years there has been considerable interest in carbonated water flooding as a secondary recovery method. Several carbonated waterflood field tests are now in progress.1'3 Yet there is no published method for predicting the results of a carbonated water flood. This paper presents a method for predicting the oil recovery for ; carbonated water flood. In a carbonated water flood. a carbonated water slug is injected into the reservoir. Then this slug is driven forward by injecting plain water behind it. The field operator must choose the carbonated water slug size and the CO2:water ratio in the slug. The calculation method presented here shows the effects of both slug size and CO2:water ratio on oil recovery. The calculation assumes that the addition of carbon dioxide to flood water increases the oil recovery by two mechanisms: 1. Carbon dioxide transfers from the flood water to the oil, thereby reducing the viscosity of the oil. At the lower viscosity, the oil flows more readily and is more easily swept out by flood water. 2. The carbon dioxide which transfers to the oil phase causes the oil phase to swell. Assume that the residual oil saturation (volume per cent of pore space) is the same whether the oil is carbonated or not. Then the same volume will contain less stock tank oil if it is carbonated, due to oil swelling. The plain water driving the carbonated water slug forward will strip the CO2 out of this residual oil., causing this oil to shrink. This swelling-followed-by-shrinking leaves behind a lower residual oil saturation than would have been left behind by a plain water flood. Since some oils swell to almost twice their original volume at reasonable CO2 pressures, this effect may be large. Two additional benefits sometimes claimed for carbonated water flooding are: 1. Adding CO2 to flood water greatly increases the water injectivity in some cases.1 (Injectivity = BPD of water injected/ft of sand x differential bottom-hole pressure, psi.) CO2 forms a weak acid in water; injecting carbonated water is, therefore, somewhat like acid treating. If a formation responds to acid treating, it will probably have a higher injectivity for carbonated water than for plain water. Although the increased injectivity increases the profitability of a carbonated water flood over a plain water flood, it does not change the production curve based on total fluid injected. Therefore, the method presented here does not show any effect of increased injectivity. 2. It is claimed in one patent4 that carbon dioxide will react with some constituents of the oil to form detergents. These detergents are expected to increase the oil recovery. There is little data available to support this idea. The calculation method presented here takes no credit for extra oil recovery due to the formation of any such detergents.

Jan 1, 1965

By O. R. Morris, G. L. Hawkes

A galvanic cell, using as electrolyte a fused salt solution of calcium carbide and as electrodes carbon and a Fe-C alloy of known composition, has been set up to study the thermodynamics of Fe-C alloys in the temperature rmzge 800" to 1000°C. Time independence and reproducibility of the cell electromotive force were taken as evidence of the reversible behavior of the cell. Carbon was believed to be present in the electrolyte as the so-called acetylide ion, C;-. The plots of the cell electromotive force us temperature for a specific alloy composition were straight lines within the limits of experimental error. The average Partial molar enthalpy of carbon in iron relative to pure carbon was found to be +10,610 i 93 cal per g-atom C. Thermodynamic analysis of the data has led to the following equation for the carbon activity, ac, based upon pure carbon as the standard state: In ac = In Zc + 10,560/RT + (10.02 + 77O/T)ZC - 2.350 where ZC is the lattice ratio [nC/(nF, - nc )] and T is the absolute temperature. This equalion gives carbon activity values generally slightly lower than those from gas equilibration studies reported in the literature. METAL LOGRAPHIC examination of a polished cross section of the steel anode used in the electrolysis studies of fused salt solutions of calcium carbide by Morris and Harry revealed extensive carburization of the steel by the electrodeposited carbon. This carburization was reflected in the variability, with time, of the applied potential to the electrolysis cell, necessary to maintain a constant current density at the electrodes. This observation suggested the setting up of a galvanic cell of the "alloy concentration" type to study the thermodynamics of some metal-carbon alloys. Cells of this general type have been widely used for the study of alloy systems.2 In view of the availability of published data in respect of the austenite phase of the Fe-C system, it was decided to carry out measurements upon these alloys before proceeding to studies of less well documented systems. The galvanic cell may be written: where [C] is carbon dissolved in iron. The electrolyte was a fused salt solution of calcium carbide, containing some 5 to 10 mol pct of carbide. The cell reaction is believed to be: C(s)-[CI [I1 Carbon forms an interstitial solid solution in iron, with the atoms located in the octahedral interstices. In the fcc crystal structure of austenite there is one octahedral interstice per iron atom. Thus, the lattice ratio, ZC, shown by Gurney3 to be the fundamental concentration parameter in the context of interstitial solutions, is given by: where nc and nFe are the number of carbon and iron atoms, respectively. chipman4 has recently shown empirically the advantages of using this concentration parameter instead of the more usual atom ratio or atom fraction. The cell electromotive force, E, assuming reversible behavior, is related to the carbon potential or the partial molar free energy of carbon in the solid solution relative to pure carbon at the same temperature and pressure, GP at the composition ZC, by the equation: where z is the carbide ion valency and F is the Faraday constant. An activity of carbon, ac, in the solution relative to the value of unity assigned to pure carbon, and an activity coefficient, qC , are defined such that: where R is the gas constant and T the absolute temperature. GF is further related to the relative partial molar enthalpy Hm, and the temperature coefficient of the cell electromotive force, (aE/aT)Zc, by the equations: Measurement of the cell electromotive force thus enables calculation of the relative partial molar thermodynamic properties of carbon in iron, if z is known. At E = 0, the solid solution is in equilibrium with pure carbon. More convenient for many purposes is the standard state based upon the infinitely dilute solution, Henry's law. The relationship between the activity coefficient of carbon based upon this standard state, and that based upon the pure carbon standard state, qC , may be obtained by considering the free energy of transfer of carbon from the latter standard state to the former. The relationship is: where +:H is the activity coefficient of carbon in the hypothetical standard state based on a reference of

Jan 1, 1969

By Gen-ichi Nakazawa, Masamichi Fujimori, Ichiro Doi

INTRODUCTION The major products of nickel industry in Japan are the electrolytic nickel (E-Ni), the ferro-nickel (Fe-Ni) and the nickel oxide sinter (NOS), totaling in production to 90 - 100 X 103 tons/year in terms of pure nickel content, and sharing approximately 20% for E-Ni, 10% or less for NOS, and the rest for Fe-Ni. The raw materials to be used for these products depend totally upon the imports from abroad; matte, the raw material used in the production of E-Ni, is from Australia and Indonesia; matte for the NOS is from Indonesia and New Caledonia; and garnierite, the raw material for Fe-Ni, is imported in bulk from New Caledonia, Indonesia and the Philippines. This report describes the acquisition of these raw materials, the production processes, trend of supply-demand, problem areas and the measures taken, and so forth, in connection with the nickel industry in Japan. ELECTROLYTIC NICKEL 1. History The nickel industry in Japan began in 1939 by the Sumitomo Metal Mining Co., Ltd. (SMM) with 150 tons E-Ni/month under the blast furnace smelting and the metal anode electrolysis. This was temporarily suspended after the end of last World War II, but resumed in 1952 with garnierite of New Caledonia as a raw material. Since then, the production capacity has been expanded incidentally to the increase of demand. However, since the smelting of garnierite contained about 2% nickel was very costly, the smelting process had been changed to smelt the briquettes of the mixture of garnierite and nickel sulfide concentrate imported from Canada and Australia. In 1975, this smelter was closed, and SMM's nickel refinery used matte from Western Mining Corp. (WMC) of Australia as a raw material. The refining process had been the metal anode one. The crude nickel oxide derived from roasting the high grade nickel matte had been melted and reduced with coke in the electric furnace and cast into anode. In 1970, a new refinery was constructed to produce 1,000 tons Ni/month under the matte anode process, and further, in 1976, the old refinery was converted into the matte anode process, thus resulting in the total production capacity of 1,690 tons Ni/ month today under the matte anode process. Shimura Kako Co., Ltd. began in 1951 to produce a little of E-Ni, and in 1955, they constructed a shaft furnace smelter with New Caledonian garnierite as a raw material to begin the E-Ni production under the matte anode process. Its monthly production reached 400 tons in 1957, but it discontinued its smeltering in 1963 to convert to the matte import from S. Le Nickel, WMC and INCO. In 1979, it changed the source of matte supply from the above to Soroako of Indonesia, discontinued the E-Ni production in 1979, and arranged for a total toll contract with Sumitomo. Meanwhile, SMM has developed a very distingished process for nickel-cobalt separation and refining by a solvent extraction method from nickel and cobalt mixed sulfide generated as a by-product in the nickel recovering process from laterite under the Nicaro process. Nippon Mining Co., Ltd. (NMC) also developed its own process. The plants under these processes were constructed in 1975, with the monthly production capacity of 230 tons of nickel and 130 tons of cobalt by SMM, and 300 tons of nickel and 110 tons of cobalt by NMC. SMM imports the raw material from the Marinduque Mining and Industrial Corp. of the Philippines, while NMC from Queensland Nickel Pty. Ltd. of Australia. 2. Production Status 2.1 Producers and materials Today, SMM holds the monthly E-Ni production capacity of 1,920 tons, of which 1,690 tons are from the matte anode process, and the remaining 230 tons are from the mixed sulfide as a raw material. NMC also uses the mixed sulfide as a raw material for a production of 300 tons/month. [ ] Most of SMM's raw material, nickel matte, is imported from WMC of Australia, partly using the Soroako matte from Indonesia. An example of material analysis is given in Table 1. Matte is a raw material for E-Ni and NOS, and the major sources of matte supply at present are Australian WMC and Indonesian Soroako, occupying ap-

Jan 1, 1982

By Klaus Schwerdtfeger

Activities of lead in Pt-Pb and Pd-Pb melts in the temperature range of 800° to 1200°C have been detev-mined from electromotive-. force measurements 202th the cells Both systems display strong negative deviations from Raoult's law. The data obtained with cell [1] were combined with available data on the activity of PbO in silica-satuvaterl PbO-SbO2 melts to calculate the standard free cnergy of formation 01- liquid PbO. FREE energies of formation of oxides and activities of components in metal and oxide melts can be determined with galvanic cells consisting of a metal phase, an electrolyte containing the oxide of one of the components of the metal phase, and an oxygen electrode. This technique has been used previously to measure the standard free energy of formation of solid sio2, 1 and activities in Fe-si, CO-si,2 Ni-Si,2 and CaO-P2O5 3 melts. The present paper reports activities in Pt-Pb and Pd-Pb melts as measured with the same experimental technique. EXPERIMENTAL METHOD General Considerations. The following cells were used: Pbl (PbO-SiO2)liquid, SiO2 Pt-Pb 1 (PbO-SiOz)liquid, SiO2solidO2 [2] Pd-Pb (PbO-SiOz)liquid, SiO2solid O2 [3] Liquid alloy and' oxide melt were contained together in a silica glass crucible of essentially the same design as described previously.1'2 The PbO-SiO2 melts are ionic conductors.' During the experiment, the silica glass crystalizes in a layer adjacent to the electrolyte. The electrolyte equilibrates with solid silica and hence attains the composition of the Si02-liquidus curve in the system PbO-SiO2 at any particular temperature. Molybdenum wires were used to establish contact with the liquid metal. The oxygen electrode, which reaches the surface of the PbO-SiO, electrolyte from above, consists of a platinum wire inserted into a ceramic tube and provided with a 2-mm-diam platinum bead at its end. Gas of known oxygen partial pressure (pure oxygen of 1 atm: air, or N2 with 1.04 pct 0,) is blown through the ceramic tube onto the surface of the electrolyte. The cell reaction is Pb (metal) + 1/2O2 (gas) = PbO (electrolyte) [4] No oxidation of platinum or palladium ("displacement reaction") occurs. This is to be expected from the noble character of platinum and palladium, but was also shown experimentally, as described in the next section. The galvanic electromotive force of the cell is given by where AG is the change in free energy for Reaction [4], E(=2) is the number of electrical equivalents necessary to form 1 mole of PbO, and F is the Faraday constant. Formula [5] is valid only if no junction potential exists within the electrolyte. Junction potentials occur only when the compositions of the electrolyte are markedly different at the electrodes. Such differences are negligible in the PbO-SiO, electrolyte, as shown in the next section. Since molybdenum contact leads are used, appropriate corrections were made on the measured electromotive forces to account for the thermoelectric effect of the Mo-Pt couple. The thermoelec-tromotive forces were measured separately with a Mo-Pt couple, and were found to vary linearly from 19 mv at 740°C to 40 mv at 1310°C with molybdenum being positive and platinum negative (cold junction at 25°C). Extrapolation of these values to higher temperatures yields values which are in satisfactory agreement with those obtained previously in the temperature range 1440° to 1630°c.1,2 The change in free energy for Reaction [4] is expressed as where chemical potentials of the species. The value of constant for a given temperature because the slag composition is fixed. Inserting [6] into [5] and using appropriate expressions for upb and uO2 the relation

Jan 1, 1967

By W. O. Philbrook, R. S. Kaplan

Rates of oxidation were studied for levitation-melted samples of Fe-C, Fe-Si, Fe-C-Si, Fe-C-P, Fe-C-Mn, and Fe-C-S alloys oxidized by mixtures of either 5 or 10 pct O2, in helium at several temperatures in the range 1850o to 2050°C. The concentrations of the oxidized elements decreased linearly with time. Mass transport in the gas phase was found to be the rate-controlling step. Ilowever, a mulliple -film model was necessary to account for the flux of iron and manganese vapor counter to the oxygen flow. THE advent of the basic oxygen and spray-refining processes of steelmaking has generated considerable interest in the kinetics of reactions between oxygen-bearing gases and liquid iron alloys. The object of this research was the determination of the role of mass transport in the gas and metal phases and of surface chemical reactions in the overall oxidation process. Of the reactions for elimination of elements dissolved in liquid iron, the oxidation of carbon has been investigated most extensively. Studies by Fuji and Ura,1 Fuji,' and Gunji et a1.,3 done with pilot-scale basic oxygen furnaces, indicated that mass transport of gaseous oxygen was rate controlling when the metal carbon content was greater than 0.15 to 0.30 pct. When the carbon content was less than this critical amount, diffusion of carbon dissolved in the iron was thought to be rate limiting. L. A. Baker et a1.4,5 levitated samples of iron-carbon alloys and oxidized them in CO-CO2, CO-C02-He, and O2-He atmospheres at 1660°C. These investigators found that the metal carbon concentration decreased linearly with time and their samples exploded when the carbon content fell below about 0.8 pct. They concluded that the rate-limiting step was the transfer of oxidant to the gas-metal interface. A model based on this rate-limiting step predicted decarburization rates within a factor of two of those experimentally observed. The explosion of the samples was attributed to a shift in rate-controlling step from gas-phase mass transport to transport of carbon dissolved in the metal. L. A. Baker and R. G. ward6 and R. Baker7 used freely falling droplets to investigate oxidation kinetics. In both papers, the authors speculated that flame fronts may have been partially responsible for the lack of better agreement between experiment and theory. Swisher and Turkdogan8 oxidized liquid iron having an initial carbon content of 0.97 pct with CO-CO2 and CO-C02-Ar mixtures at 1580°C. They concluded that a surface reaction was the rate controlling step. Iron-silicon alloys have been oxidized by R. Baker7 and Filipov and Martynov.9 R. Baker 7 also studied iron-carbon-silicon alloys falling as liquid droplets through oxygen. He found that the rate of both carbon and silicon oxidation varied inversely with the drop radius. When the initial silicon concentration was greater than 6 pct, the samples cooled during their fall. Manganese oxidation has been studied by R. Baker,7 and by Filipov and Martynov.9 ward10 investigated the loss of manganese from liquid iron under vacuum. He found that mass transport of manganese vapor was rate limiting in argon atmospheres of 0.02 torr to 700 torr pressure. Iron-sulfur alloys were desulfurized with H2-He and H2-Ar mixtures by Peters et al.11 A model based on the transport of H2S from the gas-metal interface into the bulk gas gave fair agreement between the predictions of the model and the experimental results. EXPERIMENTAL TECHNIQUE Essentially, the technique consisted of using helium-oxygen gas mixtures to oxidize levitated samples of liquid binary and ternary iron-base alloys. The fused silica reaction tube is shown in Fig. 1. The coil design is similar to that of L. A. Baker et al.4'5 A Tef-lon-sheathed, ferritic stainless steel lifter (B) and an alumina pedestal (C) were used to support the sample in the coil prior to levitation and for the recovery of the sample. Samples were inserted into

Jan 1, 1970

By R. A. Breitrick, J. N. Swinderman, J. J. Cooper, H. L. Bauer Jr.

The Robinson Mining District, near Ely, Nev., is one of the major porphyry copper districts in the world. Within the district is an eight mile long east-trending zone of altered porphyry, metamorphosed sedimentary rocks, and sulphide mineralization surrounded by Paleozoic limestone, dolomite, shale and sandstone, Tertiary volcanics, and Quaternary alluvium. Six major disseminated ore deposits have been exploited in this zone. About 20% of the district production has come from disseminated ore in metamorphosed sedimentary rocks found adjacent to altered quartz-monzonite porphyry. The following brief statements summarize some of the relations between porphyry alteration, metamor-phism, and mineralization: 1) Disseminated copper ore does not occur in unaltered porphyry or in m-metamorphosed sedimentary rocks. 2) Sedimentary rocks have been only weakly metamorphosed where intruded by unaltered porphyry. 3) Intensely metamorphosed sedimentary rocks are found only adjacent to altered porphyry. 4) Many hydrothermal minerals are common to both altered porphyry and adjacent metamorphosed sediments. 5) Disseminated ore is found in altered porphyry and adjacent metamorphosed sedimentary rocks. 6) In general, there is a direct correlation between grade of ore in porphyry and copper content in the adjacent rocks. 7) Chemical changes in the altered porphyry and metamorphosed rocks appear to be related. The foregoing relations support a hypothesis that the porphyry alteration, the metamorphism of the sedimentary rocks, and the ore deposition were all part of a continuous hydrothermal process which probably closely attended the porphyry intrusion. The Robinson Mining District, most often referred to as the Ruth or Ely District, is located in eastern Nev. and is one of the major porphyry copper districts of the world. Production from 1908 through 1962 was nearly 250 million tons of ore averaging a little over one percent copper with a total metal value of nearly one billion dollars. The ore has been produced from six major disseminated-type deposits with the Liberty Pit deposit accounting for 70% of the total district production. Less than one million tons of base metal and gold ores have been produced from the replacement-type deposits of the district. Approximately 20% of the district production has come from underground mining operations; the pit ore has been mined with shovels and removed by train haulage, truck-train haulage combinations, truck haulage, and presently by a combination truck-skip system. Many of the ore deposits formerly worked by underground methods have been and are being exploited by open pit methods. (See Fig. I.) Two co.'s have accounted for virtually the entire production from the district. In 1958 Kennecott Copper Corp. acquired the district assets of Consolidated Coppermines Corp. and is now the sole ore producer in the district. Present operations are confined to the Liberty Pit where 22,500 tons of ore averaging a little less than 0.8% copper is mined per day. Cutoff grade is 0.4% copper, and the stripping ratio is three to one. The ore is hauled by rail 23 miles to the McGill Reduction Plant where it is concentrated to about 20% copper. Molybdenite is recovered as a by-product in the mill. The copper concentrates are smelted in McGill, and the blister copper is shipped for refining to Balt. where gold, silver, platinum and palladium are recovered. The Robinson Mining District has been well known as a porphyry copper district for the past fifty years, but many geologists are unaware of the fact that a large portion of the production has come from disseminated ore found in metamorphosed sedimentary rocks. The scope of this paper describes the occurrences of disseminated ore in the various metamorphosed sedimentary rocks, and presents evidence for the hypothesis that these ores are genetically, spacially, and coevally related to the disseminated ore in the porphyry rocks. Publication of this paper was granted by the management of Kennecott Copper Corp. A. H. James suggested and encouraged the writing of the manuscript. Special mineralogical and spectrographic analyses were performed by the Kennecott Research Center. The deposits of the district have been studied by many geologists since the turn of the century, and

Jan 1, 1964

By M. M. Fine

THE problem of producing a uniform, medium-fine sand for glass-furnace feed has been of interest to the glass-container industry for many years. In the present investigation of the problem, conducted by the Bureau of Mines in cooperation with the Owens-Illinois Glass Co., Alton, Ill., a satisfactory method of producing such sand was developed. The investigation involved continuous-grinding studies of glass sand with flint and porcelain pebbles, steel balls and rods, and a simultaneous study of classification. The most satisfactory procedure consisted of grinding in a pebble or ball mill followed by a double classification: hydraulic classification to separate the oversize for return to the grinding unit and mechanical classification to remove fines and impurities from the ground sand. The proper application of this flowsheet usually yielded a graded sand containing less iron than the feed even when grinding was done in a steel-lined ball mill. The amount of sand ground into the so-called "dusting" sizes was, in all cases, less than 10 pct. Experiments were made which showed that this very fine sand could be beneficiated to a usable material. Background The advantages in utilizing a uniform, medium-fine sand as a feed for glass furnaces has motivated a considerable amount of research on the ,problem of producing such sand by glass producers and others. For the glass producer, the faster melting rate of such a graded sand offers the possibilities of reduced fuel costs and increased furnace capacity. In addition, there is the likelihood of improving the quality of the melt and thereby reducing the number of seeds (air bubbles) and stones (unrnelted grains) in the finished ware. Although the melting rate of a glass batch depends on other factors in addition to the grain size of the sand, there is experimental evidence to show that grain size influences the melting rate considerably. Potts, Brookover, and Burch' found that when the raw materials (sand, soda ash, and limestone) were always matched in- size, there was a great decrease in the melting time as the grain size of the materials was decreased. They found, too, that when the grain sizes of the soda ash and Limestone were held constant at 40 to 60 mesh, the minimum melting time occurred when 40 to 60 mesh sand was used. The increase in melting time with decrease in grain size beyond 40 to 60 mesh was due, they postulated, to accelerated demixing or separation of batch during melting as the grain size of the sand decreased in relation to the grain size of the other materials. An earlier investigatora found that the highest rate of melting and purifying ordinary glass was obtained when medium-size sand (0.385 to 0.120 mm, correspondingly roughly to 40 to 120 mesh) was used. Although batches containing smaller-size sand were found to fuse more rapidly, the time required to remove air bubbles from such melts actually increased the total duration of the process. Coarsegrained sand, it was stated, increased greatly the times of both melting and purifying. Although the laboratory data are difficult to confirm on a plant scale, observations by the Owens-Illinois Glass Co. indicate a higher furnace capacity of better-quality ware when a medium-fine sand is used in the batch. During the recent war, the glass producer was inclined to overlook a considerable variation in raw materials in the interest of higher production. For instance, table I shows the wide range in the amounts of various screen fractions in sand supplied by one producer to the Terre Haute plant of Owens-Illinois. The sand, from the northern Illinois St. Peter sandstone, represented material used by that plant over a period of a few years during the war. Since the war, the glass industry has insisted on

Jan 1, 1951

By K. T. Aust

The relative interfacial energies of symmetrical tilt boundaries in silver of greater than 99.999 pct purity were measured as a function of orientation difference 0 between 9° and 36° about <001>. The results are in good agreement with the dislocation model of the grain boundary. The energy vs H curve may be represented by the Shockley and Read equation in the form Eoe (0.55—In 8). READ&apos; has indicated that an ideal experimental method of testing the predictions of the dislocation theory of the grain boundary would be to measure the interfacial energies of symmetrical tilt boundaries between face-centered-cubic grains that have a common <001> axis, as a function of orientation difference 0. The misfit H should be defined by a rotation of each grain through an angle of H/2 away from the boundary. Such boundaries might be expected, from geometrical considerations, to be made up of a series of edge dislocations, at least for small values of 0. Energy vs H relationships for tin&apos; and lead:&apos; were previously obtained for an asymmetrical tilt boundary separating two grains in which generally only one grain was rotated about a <001> specimen axis through an angle of H away from the boundary, the other grain remaining fixed. It is possible, however, that the boundary atoms in tin and lead may have attained a symmetrical position, in relation to the orientations of the grains on either side of the boundary, during equilibrium annealing. The two sets of measurements on silicon ferrite&apos; were somewhat better suited for comparison with theory, since the boundaries were symmetrical tilt boundaries in which the axis of relative rotation was <110> in the first series and <l00> in the second; but this alloy has a body-centered-cubic structure. Although the grain boundaries in silver" were symmetrically tilted, the axis of relative rotation was not a simple crystallographic direction, and it varied from boundary to boundary. Although the above measurements were in good agreement with the Shockley and Read equation,"&apos;: it appeared desirable to carry out experiments under the ideal conditions specified by Read.&apos; Consequently, the relative energies of symmetrical tilt boundaries in silver between grains that have a common <001> axis were measured. The technique of equilibrating grain boundaries in oriented tricrystals was used rather than the less satisfactory thermal groove method previously employed for silver bicrystals." Experimental Details and Observations The solidification and seeding techniques, described previouslyh for growing tricrystals of controlled orientations, were used to prepare tricrystal specimens from silver of greater than 99.999 pct purity. The silver was obtained from American Platinum Works, Newark, N. J., in the form of poly crystalline rods 10 cm long and 7 mm in diam. These rods were then cold worked by rolling or drawing them into suitably shaped blanks. Single crystal seeds and tricrystals were grown in a high purity graphite boat by means of a movable furnace with globar heating elements. The graphite boat was enclosed in a Vycor tube, which was first evacuated to about l00/u Hg and then filled with a static argon atmosphere. The maximum temperature outside the Vycor tube was 1250°C. A typical tricrystal specimen of silver is shown in Fig. 1. Grains B and C were grown from seed crystals with a <001> specimen axis or longitudinal direction parallel to the direction of growth and with another <001> direction perpendicular to the surface. Each of the two seed crystals was rotated 18" about the <001> specimen axis but in opposite directions away from the boundary. A symmetrical tilt boundary, therefore, separated grains B and C with an orientation difference 8 of 36" about <001>. Grain A in Fig. 1 was grown from the middle seed with a <110> direction parallel to the specimen axis and with a <001> direction inclined at 45&apos; to the surface of the specimen. The interfaces sepa-

Jan 1, 1957

By W. J. Babyak

The habit planes for hydride precipitation in large grains of alpha zirconium and Zircaloy-4 were determined in specimens containing 161 and 136 ppm hydrogen, respectively. In zirconium, the hydride platelets precipitated on various pyramidal planes inclined to the basal plane at angles ranging from 10 to 50 deg and 75 to 90 deg. Hydrides were most frequent at inclinations of about 20 deg and 90 deg. In Zircaloy-4, hydride plates were inclined to the basal plane at angles vanging from 5 to 25 deg with the predominant inclinatioiz equal to 12 deg; no platelets were found near the prism plane position. In both zircoinium and Zir-caloy-4, hydrides were principally, but not exclusively, parallel to (1011) type planes. When the Zircaloy-4 gmins were subjected to tension stresses of 12,100 psi and 19,400 psi during hydride precipitation, the hydride habit was unchanged except that precipitation favored those habit planes which were inore nearly perpendicular to the stress direction. The stress-orientatioiz effect increased with the magnitude of the stress. THE hydride habit plane in a zirconium has been determined by several investigators. Langeron and Lehr1 in 1956 found platelets parallel to (1010) slip planes. In 1962, Westlake and Fisher2 confirmed these findings and showed that hydride precipitation on twin planes, as reported by Kunz and Bibb,3 was probably due to incomplete removal of worked metal from specimen surfaces. Secondary habit planes, ( 1011) and (1015), were also found by Westlake and Fisher under particular charging conditions where a hydride layer may have existed at the hydrogenation temperature. Most recently, walters4 and westlake5 again observed the (1010) habit exclusively in zirconium. Louthan and hgermans have reported that hydrides precipitate on various ( 101l ) and (112l) planes positioned 31.5 to 90 deg to the basal plane in Zircaloy-2. The present investigation was concerned with the hydride habit in Zircaloy-4 in relation to that in zirconium and the possible change in habit when precipitation occurs under stress. The latter consideration was prompted by the stress-orientation phenomenon originally reported by Marshall and Louthan.7, 8 I) EXPERIMENTAL Materials and Specimens. Chemical analyses of all materials are given in Table I. The zirconium specimen was a 1 by 4 in. section cut from wrought crystal bar that was hot-rolled at 790°C to 0.300 in. and cold-rolled to a final thickness of 0.095 in. All surfaces were mechanically polished and then chemically polished with a solution of H2O, HNO3, and HF (10:10:l by volume) prior to annealing. Grains as long as 0.25 in. were grown by thermally cycling the specimen three times (in 10-5 mm Hg vacuum) between 825" and 1000°C at approximately 125°C per hr. The specimen was isothermally annealed at 825°C for 24, 40, and 120 hr after each cy-

Jan 1, 1968

By D. B. Hunter, H. W. Rosenberg

The titanium-rich portion of the Ti-Pd system was investigated from 0 to 75 wt pct Pd by metallo-graphic and X-ray techniques. A 0 eutectoid occurs at 24 wt pct Pd and 1190°F. Two compoutzds are indicated in the region below 75 wt pct Pd, Ti,Pd and Ti2Pd3. The solubility of palladium its a titanium is low, probably less than 1 pct. In 1960 Rudnitskii and Birunl published a complete version of the Ti-Pd phase diagram. However, their work was in disagreement with the earlier literature in that they reported only one inter metallic compound, whereas three had been reported earlier. In view of these discrepancies, it was therefore necessary to redetermine those portions of the diagram of immediate interest. The following account describes our work on the system over the range of 0 to 75 wt pct Pd. MATERIALS AND METHODS Distilled titanium sponge and elemental palladium were used in the formulation of the alloys; the chemistry of these materials is detailed in Table I. The alloys were prepared as 10 to 50 g blended compacts that were melted into buttons by arc melting under gettered argon on a water-cooled copper hearth. Weighing of the ingredients before and after melting showed that negligible weight changes occurred. Therefore, no analyses were undertaken and the compositions of all alloys are nominal. All alloys were fabricated by hot rolling at 1700°F to 0.070-in.-thick sheet. Scale was removed by sandblasting and pickling in a 5 pct HF-35 pct HNO,, balance H20 solution. For metallographic examination, specimens were mounted after heat treatment transverse to the rolling direction, ground on silicon carbide papers of increasing fineness to 600 grit, and then electro-polished using a solution containing 600 ml me-thanol, 60 ml perchloric acid, 360 ml butyl cello-solve, and 2 ml "Solvent X". Unless otherwise specified, etching of alloys containing up to 42 pct Pd was carried out by swabbing with a 12 pct HN03-1 pct HF aqueous etch where a bright etch was required, or by a 1 pct hydrofluoric in saturated oxalic acid solution where contrast between phases was required. The Ti-52.8 Pd alloy was etched with a solution of 25 ml HF, 40 ml glycerine, 35 ml methanol, and 18 g benzalkonium chloride. For X-ray examination, 1/2-in.-square speci- mens of sheet were mounted flat in a standard 1-in. metallographic mount and ground and polished as above. X-ray diffraction was performed using a Norelco type 12045 Diffractometer, employing CuKa radiation with a nickel filter at 40 kv and 20 ma. Specimens were rotated about the sheet normal during exposure. Although this procedure did not remove the effects of sheet texture from the relative intensities, it had the advantage that oxidation or contaminants entering during preparation of powder samples could not confuse the patterns obtained. RESULTS AND DISCUSSION Fig. 1 illustrates the Ti-Pd phase diagram according to Rudnitskii and Birunl with the work of the present authors superimposed. Both interpretations agree that the system is of the 0 -eutectoid type with an extensive 0-phase field, and that the eutectoid temperature is just below 1200°F. There is also agreement that the solubility of palladium in a titanium is restricted. Our work would indicate that the a solubility of palladium is low, probably less than 1 pct. However, whereas Rudnitskii and Birunl place the eutectoid composition at 41 wt pct Pd, this investigation shows it to be at about 24 wt pct Pd. Moreover, this investigation confirms the existence of compounds at Ti2Pd and Ti2Pd3, whereas Rudnitskii and Birun report only a single Berthol-lide phase covering the TiPd to TiPd, range. Laves et a1.&apos; and Wallbaum, whose work was summarized by Maykuth , reported the existence of Ti2Pd3 and TiPd, in addition to Ti2Pd. More recently, Nevitt and Downe~&apos; have reported the structure of

Jan 1, 1965

By B. L. Averbach

Recovery and primary recrystalliza-tion in cold worked metals are usually considered as two competing processes. Some of the effects which usually accompany recovery are: alleviation of stress corrosion tendencies, changes in thermal emf,1 damping capacity,2 electrical resistivity,2 and magnetic properties,3 and only minor changes in hardness or the related strength properties. During primary recrystalliza-tion new unstrained grains are formed at the expense of the strained matrix. These new grains eventually become visible metallographically, and nucle-ation and growth kinetics have been indicated for this process.4,5 Frequent attempts have been made to study the cold-working phenomenon by observations on the line broadening by X ray diffraction patterns. Relatively few measurements of line intensities have been made, although Brind-ley and his collaborators, 6,7,8 by means of film techniques, compared the intensities of cold worked Cu, Ni, and Rh patterns with those from chemically precipitated powders. These precipitated powders were presumed to be strain free, and it was found that the intensities for the cold-worked materials progressively decreased as the Bragg angle increased except for the first line, where there was an increase due to reduction in extinction. This was interpreted as a randomness in atomic position induced by cold work. Such randomness is similar to that caused by thermal agitation and has been described as "frozen heat" displacement of 0.08-0.10 A from the mean atomic position. In a recent study9 on the effect of cold work in metals on their powder pattern intensities, the changes in integrated intensity for heavily cold worked alpha brass were observed as a function of the annealing temperature. These measurements were made with a manually operated Geiger-counter spectrometer using CuKa radiation monochromated with a rock salt crystal. Intensity measurements were made with a scaling meter over small intervals of angle, and the equipment was so arranged that the diffracted and incident beams made equal angles with the specimen. Intensities could be compared directly by simply interchanging specimens, and comparisons from day to day were made with a standard whose line intensities did not change on aging. It was shown that a cold worked alpha brass standard was stable for at least a year. Table 1 indicates the results of the integrated intensity measurements on a 70 Cu-30 Zn brass. In the sample preparation, a brass plate was first cold rolled 50 pct and then filed, screened to —325 mesh, compacted into briquettes at a pressure of 60,000 psi and finally annealed for one hour at various temperatures up to 400°C. The briquetting pressure did not seem to influence the integrated intensities, and most of the cold work was introduced by the filing. Although this method of cold work is not quantitative, it was used to obtain random orientation (and thus uniform diffraction lines) in order to make accurate measurements of integrated intensity. Back reflection patterns were taken in each case to check the uniformity of the lines, and from the observed line broadening it was apparent that this type of plastic deformation was quite severe. Care was taken to traverse the entire background of the pattern and to assign to each peak the total intensity above this background. The bases of the diffraction lines were quite broad and spread out over several degrees, even for the narrow peaks. The theoretical intensities were calculated to include a temperature correction, a dispersion correction, and a Lorenz- polarization factor corrected for the crystal monochromated beam. In Table 1 it was necessary to match the calculated and observed values at only one point, and the rest of the experimental values were converted directly to this arbitrary scale. The integrated intensities in Table 1 are listed in arbitrary units, and the accuracy was sufficient to reproduce any of the measured line intensities to within + 1.5 units. It is evident that the percentage error on the strongest line (111) was quite low. The calculated values and the observed intensities for the cold worked material matched reasonably well. As the annealing temperature was raised, however, the intensity of the strongest reflections, particularly the (lll), decreased measurably. Since the background intensities of all of these patterns were identical, such behavior could be interpreted as a primary

Jan 1, 1950

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing and shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization—one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subsequently mineralized by sulphides and barite. Introduction Buchans is 5 miles north of Red Indian Lake, in Central Newfoundland, at an elevation of 900 ft. above sea level and 400 ft. above Red Indian Lake, and is reached by a 37-mile private railway from Miller-town Junction. The first ore body found at Buchans was discovered some 30 years ago in the bed of Buchans River, by Matty Mitchell, an Indian woodsman employed by the Anglo-Newfoundland Development Co. Ltd. In the years following the discovery the ore was developed by shaft-sinking and drifting, with results indicating a lenticular ore body in a shear zone, containing about 100,000 tons of extremely fine-grained sulphide ore in barite gangue averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Cu, 10 per cent Pb, 18 per cent Zn. Because a profitable metallurgical treatment for the ore was not found, the mine was closed down in 1911. In 1915, Mr. H. A. Guess, Vice President of the American Smelting & Refining Co., learned of the Buchans River ore body, and after metallurgical tests had been carried on from time to time in his company&apos;s testing plant a satisfactory separation of the sulphides by selective flotation was finally effected in 1925. Prospecting for additional ore bodies was begun in 1926, utilizing geophysical methods under the direction of Hans Lund-

Jan 1, 1937

By F. W. Jessen, H. Kazemi

A washing technique has been developed to form a spherical cavity in massive salt. The technique is, basically, a process of controlling the fluid motion in the cavity, the concentration distribution of brine, the rate of dissolution at the walls of the cavity, and the particular settings of the wash pipe, or pipes (inlet and outlet pipe) employed. For a particular arrangement of tubing and casing, fresh water enters from the casing annulus at a position above the bottom of the tubing, and the dissolved material leaves the cavity through the tubing near the bottom of the projected hole. The initial configuration of the cavity is cylindrical, representing the drilled hole situated at the axis of the projected cavity. As washing progresses the original hole is enlarged radially (any direction perpendicular to the axis of the hole). An inert fluid (generally a hydrocarbon, natural gas, or air) which serves as a blanket is injected through the annular space between the original hole and the casing. The controlled downward motion of this blanket maintains the upper edge of the brine region that is expanding on the surface of the projected sphere. A large spherical glass container and a radial model were used to investigate the flow patterns and the concentration distribution of brine occurring during the progress of solution of the salt. Aluminum flakes and dye were injected and flow patterns were observed and recorded on motion picture film. Based on the results of these model studies and other work carried out in this laboratory, the controlled washing technique was formulated. INTRODUCTION Underground cavities leached in salt beds and salt domes have been used extensively for storing hydrocarbons. Little attention has been focused on the shape of the cavities as long as large volumes were obtained and the cavities were structurally stable. The general process involves circulating fresh water and removing brine. Two distinctly different circulating systems can be employed, each of which yields characteristically different shapes. By far the most generally accepted method of washing storage caverns in salt domes is the direct circulation system. Water is introduced through the innermost pipe of a concentric pipe system, and brine is withdrawn through the annulus. In the reverse-circulation method, water enters through the annulus and is discharged through the smallesc tubing string. The size of the operation, and hence the size of tubing and casing used, depends on such factors as cavity volume, length of hole, availability of water, disposal of brine and power requirements. Underground caverns are from 100 to 1,000 ft or more in length, and when completed vary from 40 to 100 ft in diameter, providing storage of 100,000 bbl or more. The volumes of water required per volume of salt removed vary from 6 to 7 for the reverse circulation method to 10 to 11 for the direct circulation method. Up to 80,000 BWPD are often circulated. In the direct circulation method, because water enters near the bottom of the projected cavity, solution of salt is greatest at this point, particularly in view of the fact that when the washing is begun turbulent flow undoubtedly exists in the immediate vicinity of the discharge of the inlet water. As the diameter of the hole increases, flow rates also are increased, so perhaps the condition of fluid turbulence is maintained for some time. During the later stages of leaching, when capacity of equipment may be the limiting factor in maintaining flow rates, there may still exist some turbulence adjacent to the point of influx; however, for the most part laminar flow conditions prevail. There appears, therefore, rather good evidence to indicate that the state of fluid motion is responsible for the typically shaped cavity which results from such washing — namely a cylindrical form, generally somewhat larger at the bottom than at the top. Depending on the number of so-called stages which might be employed, the walls or surfaces of the salt diminish rather uniformly from bottom to

Jan 1, 1965

By R. C. Davis, R. F. Berry, G. W. White, B. T. O’Connell, L. A. Stacha

The formation density logging tool provides a radioactivity measurement that yields formation densities in situ. The relationship between bulk density and porosity is well understood. With knowledge of grain and fluid densities, porosity may be computed from the indicated formation bulk densities in shale-free formations. The porosities thus determined may be used with a resistivity log for water-saturation determinations. One technique utilizes a density vs resistivity plut. A plot of density vs Sonic-log transit time is used for porosity determinations in shaly sands. This method is particularly suited to wells drilled with oil-base or salt muds. In shale-free formations, comparisons of density values nnd neutron-log readings are used to identify lithologr and, thus, to select appropriate values of grain density for porosity computations. Through the use of Formation Density, Sonic and neutron logs, the interpretation problems caused by complex matrix lithologies are simplified. Other applications of the Formation Density log are found in the identification of minerals in evaporite deposits and in yield determinations of "oil shales". INTRODUCTION Widespread field application has demonstrated that the measurement of formation density is a useful and revealing technique for well logging. Responding to the bulk density variations of the formation, the Formation Density log affords valuable data on the porosity, lithology and fluid content of the formations. Although not without its own limitations, the Formation Density tool may provide effective interpretation under conditions that hamper or preclude the use of other porosity devices. When used in conjunction with other devices, such as the Sonic or neutron, complex matrix conditions may be better understood, defined and evaluated. A previous paper&apos; described the valuable contribution of the Formation Density tool in the logging of empty, or gas-filled, holes. The purpose of the present paper is to describe applications of the device in liquid-filled holes. THE FORMATION DENSITY TOOL The Formation Density tool was devised to measure the bulk densities of formations in situ. Actually, the device responds to electron density, but in the overwhelming majority of cases of interest, the electron density is very closely proportional to the bulk density. In other cases appropriate corrections can be made if necessary. Comparisons of log-derived densities with true densities for the more common matrix minerals are shown in Table 1. The tool consists of a gamma-ray source and detector mounted in a skid which, during the logging operation, is in contact with the borehole wall (see Ref. 1 for schematic). Gamma rays are emitted by the source and diffused through the formation. The number of diffused gamma rays reaching the detector at a fixed spacing from the source are counted. An increase in counting rate by the detector indicates a decrease in bulk density in front of the skid. Conversely, a decreased counting rate signifies an increase in bulk density. A measurement of hole diameter, between the face of the skid and that of the eccentering arm, is recorded simultaneously with the measurement of diffused gamma rays. Since the tool is a wall-contact device, the size of the borehole has little influence, provided good contact is maintained with the wall of the hole. Only in extremely large or small boreholes does the actual diameter become significant. However, for most accurate measurements the borehole size should be taken into account. Fig. 1 presents the departure curves for the conversion of counting rate to bulk density for liquid-filled holes of various sizes. It is of utmost importance that the skid maintain good contact with the wall of the hole. If, due to roughness or caving, there is mud between the skid and the formation, the tool will include in its response the relatively low-density mud, and the apparent density reading will be too low. Normally, permeable beds do not cave appreciably, so that reliable readings are usually available for zones of interest. Nevertheless, the caliper reading over the zone of interest should be examined for any wall roughness. When mud cake exists between the skid and the formation, the Formation Density log sees it as part of the formation. When thick mud cakes exist, a correction is required. For best results in wells having thick mud cakes,