Search Documents

By R. B. G. Yeo

Pronounced isothermal martensite formation at room temperature was measured dilatometrically in a steel containing 0.01 pct C, 24.9 pct Ni, 0.26 pctAl, 2.58 pct Ti and 0.25 pct Cb. It is shown that martensite will form isothermally if stabilization of the austenite-martensite transformation is eliminated by removal of carbon. The decarburization of two iron-nickel alloys allows isothermal transformation to martensite to occur at temperatures above their athermal Ms temperatures. In an Fe-22.4 pct Ni alloy, at the 0.008 pct C level, the Ms temperature during air cooling is 85°F higher than that during- water quenching-. At the 0.15 pct C level this difference is reduced to only 5°F. The introduction of carbon causes stabilization during air cooling which lowers the Ms temperature virtually to the same level as determined during mate?. quenching. Thus in the 0.15 pct C alloy, the Ms temperature is almost independent of cooling rate. It is suggested that rival theories of martensite formation should be reexamined in alloys of sufficiently low carbon and nitrogen content to eliminate the complication of stabilization. The Ms temperature of a steel containing 0.01 pct C, 24.9 pct Ni, 0.26 pct Al, 1.58 pct Ti and 0.15 pct Cb, solution treated at 1500°F and air cooled as 1/8-in. diam specimens, was found to be 57 °F. 1 However, when held for several hours at room temperature the steel hardened slightly and became appreciably ferromagnetic. Isothermal transformation to martensite was first revealed by Kurdjumov and Maksimova2 in an iron-base alloy containing 0.6 pct C, 6.0 pct Mn and 2 pct Cu. Most of the other studies of isothermal martensite have also been confined to highly alloyed steels which transform at subzero temperatures; for instance, DasGupta and Lement, 3 Cech and Hollomon, 4 Machlin and Cohen,5 Shih, Averbach, and Cohen.6 Averbach and cohen7 noted a rapidly decaying volume increase at room temperature in a steel containing 1 pct C, 1.5 pct Cr and 0.2 pct V. cina8 and Marshall, Perry, and Harpster9 have described the isothermal transformation to martensite at room and subzero temperature in stainless steels. Kurdjumov10 has recently reviewed the subject, noting that the isothermal formation of martensite can be observed only in the temperature range somewhat below Ms or below -50°C. The isothermal formation of martensite may be characterized as follows: 1) It occurs in steels of widely different compositions, the main prerequisite being a low transformation temperature. 2) The transformation occurs by the formation of new plates and not by the growth of old ones. 3) The isothermal transformation is suppresed by stabilization during slow cooling or holding at temperatures near room temperature. However, the factors governing this mode of transformation are still not fully understood. The formation of martensite isothermally suggests an activated process. The early theories of martensite formation did, in fact, utilize classical nucleation concepts. Kurdjumov 11 first proposed the presence of thermally activated nuclei of different sizes and compositions which would grow if they reached critical size during cooling. This treatment was enlarged and developed quantitatively by Fisher, Holloman, and Turnbull12,13 and was later reviewed by the latter two authors.14 Fisher15 associates Ms with a nucleation rate of one per cc per sec. At slightly higher temperatures the nucleation rate is so low that isothermal formation of martensite is not observed in reasonable times. At slightly lower temperatures the nucleation rate is so high that it could not be suppressed by rapid cooling. By judicious use of parameters Fisher 16 was able to obtain good agreement between classical nucleation theory and the incubation times of martensite formation.4 However the application of these principles to martensite formation in iron-nickel alloys15 predicts that an alloy containing about 30 pct (31 at. pet) Ni would not transform. The presence of an Ms temperature at -223° C in an alloy containing 34.1 pct (33 at. pct) Ni led Kaufman and cohen17 to reject the hypothesis of homogeneous nucleation in favor of the reaction path theory originally proposed by Cohen, Machlin and Paranjpe.18 This theory conveniently explains the formation of martensite athermally but becomes labored when dealing with isothermal formation. Kaufman and cohen19 did explain the isothermal activation of embryos by assuming it to be a result of the expansion of their boundary dislocation loops but this treatment predicts an upper temperature limit of isothermal martensite formation.

Jan 1, 1962

By J. B. Campbell, V. V. Valleroy, B. T. Willman, L. W. Powers

A steam drive of heavy oil was field tested in a shallow, low oil-saturation formation near Deerfield, Mo. The pilot was conducted in the Warner formation, a sandstone containing an 18' API oil having 1,000-cp viscosity at the 60F origind reservoir temperature. The formation war at a depth of 160 ft. Steam was injected into nine input wells arranged in an array of inverted five-spot patterns. In the completely confined center pattern, 14 temperature observation wells were installed to obtain thermal data and observe test progress. Late in the test, slugs of ammonia were injected to trace the flow paths of injected fluids. From the test area about 7,000 bbl of oil were produced. Data were obtained on areal and vertical temperature distribution, steam front advance, reservoir fluid movement and terminal saturations. This field test of a steam drive (I) demonstrated the feasibility of the method, (2) confirmed that the low residual oil saturations observed in the laboratory are obtained in the steam-swept region in the field and (3) provided recovery and conformance data for one set of field conditions. INTRODUCTION The Deerfield steam drive pilot test was conducted in a shallow sandstone containing 1,000-cp oil. The venture was undertaken cooperatively by the research and production departments of Carter Oil Co., which organizations have since been consolidated into Esso Production Research Co. and Humble Oil & Refining Co.. respectively. The production department was interested in steam injection at Deerfield because it appeared to be the most promising method of commercially producing this heavy oil deposit. The research department was interested in applying the new recovery method and in evaluating its performance in the field. At the time the test was begun, the initial oil saturation was not well known. Subsequent air coring and early pilot results confirmed that there was too little oil in place for profitable commercial exploitation by steam. Pilot termination at that time, however, would have been premature for evaluating field performance of the process, and the tert was continued to obtain additional data on steam injection as a recovery method. The test was located in Vernon County, Mo., about 10 miles north of the town of Deerfield and only a few miles from the Kansas border. The pilot site was selected as typical of the area. The location represented neither the highest nor the lowest oil saturation region in the acreage under lease in 1954. The steam drive was conducted in the Warner sandstone of Lower Pennsylvanian age. At the test site the top of the Warner occurs at about 160 ft subsurface and the formation is a fine- to medium-grained micaceous sandstone that dips gently to the northwest at the rate of 12 to 15 ft/ mile. A cross-section and permeability profile of the test location are shown in Fig. 1. At the pilot location the average total thickness of the Warner formation is about 43 ft, but the effective thickness for steam drive is 26 ft. Two distinct types of hydrocarbon saturation are apparent. The lower portion of the total sand, averaging about 17 ft thick, contains a very heavy asphaltic material that will not flow under the influence of a steam drive. This bottom interval, referred to as a dead oil residue, was not considered as part of the net sand undergoing steam exploitation. The initial formation and fluid properties of the upper 26 ft in the test area are summarized in Table 1, and variation of oil viscosity with temperature is shown in Fig. 2. Imbibition tests on preserved core samples taken at the end of the pilot test showed that the Warner sandstone was then neutral or slightly water-wet. Initially, the reservoir may have been strongly water-wet as indicated by low relative permeability to water during both water injection testing and early steam injection. PRIOR HISTORY Initial production tests of wells at the pilot site produced water with only a faint show of oil. No gas was produced except at Well 7-W in the pilot area and at another well about 1/3 mile northeast of the pilot. Prior to the start of the steam drive, a two-well water injection test and a two-well air injection test were conducted. No oil was produced by either. Water was pumped into Well I-W in the northeast corner of the pilot area with simultaneous production from Well 1 (Fig. 3). The air-injection tat was run at input Well 9-W and its offset, Well 2, in the southwest corner. Air and water injectivities were about the same when corrected for viscosity and pressure differences.

By J. M. GLEDHILL

IT would doubtless have been felt by many but a few years back that there was little left to be said on the subject of crucible tool-steel, and that something akin to finality had been arrived at in its manufacture and general treatment. Probably such feeling was justifiable when it is remembered that the making of steel in crucibles is by far the oldest method known, dating back from time immemorial, it being indeed impossible to accurately trace its origin and earliest development; but it seems certain that carbon-steel was made and used thousands of years ago for cutting-tools. Proof of this may be seen by the marvelous carvings and workings on the intensely hard stone-work of the ancients, for it would be difficult to conceive by what means, other than with steel tools, such work could have been executed; and it is wonderful to contemplate that steel cutting-tools should have been used so long ago, whilst the principle of manufacturing them-that is, by fusion of iron and charcoal in crucibles-was then in a measure on the sane lines as we work on at the present day. Archaeologists have discovered that the Chinese made steel in crucibles long before the Christian era. " Wootz " steel fabricated in India centuries ago was crucible steel, as was also the celebrated Damascus steel, produced at the forges of Toledo, and, curiously, this latter steel furnishes' yet another proof that "There is nothing new under the Sun," for it is recorded that Damascus steel contained certain percentages of tungsten, nickel, manganese, etc., some of the very elements, in fact, contained in the present modern high-speed steel, so that a latent high-speed steel may be said to have existed

Mar 1, 1905

By J. Fred Johnson

MORE ORE is mined in the Bingham District than in any other mining district in Utah. In addition to the open-pit operations of the Utah Copper Co., there have been, many large underground mines. Until recent years the principal production was from the Jordan and Commercial limestones, but in the last eight years valuable ore deposits have been developed in the so-called alphabetical or "A," "B," "C," and "D" limestones, mainly by the U. S. Smelting, Refining & Mining Co. The value of these developments has led the company just mentioned to acquire large holdings in the district and within the last year to install at the Niagara shaft a hoist capable of going to a vertical depth of 4000 ft., or 1800 ft. deeper than the present lowest level. Ore from Bingham has been the chief factor in enabling the

Jan 1, 1934

By W. F. Domis, F. von Gemmingen, F. Garofalo

The effect of rain size on the creep behavior of an austenitic iron-base alloy has been studied at 1300° F under conditions of constant stress. The average grain diameter varied between 9 and 190 p (ASTM 10.7-2). The subgrain size and apparent activation energy for creep were not found to depend in any systematic manner on gain size. Grain hozmdary serrations were observed in all specimens tested. The variation of the secondary-creep rate, 2,, with the pain diameter, 1, is given by: es = K(213m + 1 )/l.]; 1, is the grain diameter zohere is reaches a minimum. Results in the literature shoujthat 1,increases as the temperature increases. At low creep temperatures is is therefore proportional to 12, at intermediate temperatures <, exhibits a minimum, and at high creep temperatures is is proportional to 1/1. The dependence ofis on the stress, u, is given by: t, = A" (sinh acrln, a and n show little variation with 1. The dependence of A" on 1 is given by: A" = KA[(21k + 13)/1]. For 1 » >>lmn = 4, and at constant values 01- isat lozu stress levels, the steady-state stress is given by the Hall-Petch relation. The variation of c, with grain size is believed to he associated particularly with grain boundary generation of dislocations which becomes more important with increasing temperatures. SEEMINGLY inconsistent experimental findings have led to a certain amount of confusion concerning the effect of grain size on creep behavior. The confusion is attributed to a lack of test results obtained over sufficiently wide ranges in grain size, stress, and temperature. Experimental results presented in this paper and results available in the literature1-5 show a consistent behavior and lead to a unified concept for the dependence of secondary-or steady-state creep rate on grain size. In accordance with this concept, which is substantiated experimentally, secondary-creep rate should increase with increasing grain diameter at low creep temperatures, leading to greater creep strengths for fine-grained materials. At intermediate temperatures the secondary-creep rate should decrease to a minimum and then increase as the grain size is increased. At high creep temperatures the secondary-creep rate should decrease with increasing grain size, leading to greater creep strengths for coarse-grained materials. Whether a temperature is high or low for creep in a metal or alloy depends primarily on its melting temperature. MATERIAL AND TEST PROCEDURES The material tested was an austenitic iron-base alloy of the following composition (wt pct): C, 0.005; N, 0.017; Mn, 1.26; Ni, 14.21; and Cr, 17.18. Two 15 -lb ingots were forged and hot-rolled to 5/8-in.-diam bars which were then cold-rolled and cold-swaged to a diameter of 0.49 in. These were sectioned into 3-in.-long blanks and heat-treated at various temperatures to obtain different grain sizes. The procedures employed and the results obtained are summarized in Table I. The secondary treatment at 1400° F followed the primary treatment without intermediate cooling to room temperature. This final treatment was employed to minimize various effects arising from heating to different temperatures during the primary treatment, particularly differences in intragranular dislocation structure, segregation of interstitial atoms at grain boundaries, and density of grain boundary ledges. The intragranular dislocation structure was examined by electron transmission metallography after each of the treatments described in Table I. Isolated dislocations and a few tangles were observed but no evidence of subgrains was found after any of the treatments. No grain-size effect was evident on the density and distribution of dislocations. Stabilization of grain boundary structure is particularly important because, as will be discussed later, grain boundaries influence high-temperature creep behavior. Magnetic-permeability measurements after each treatment and

Jan 1, 1964

By R. W. Armstrong, D. H. Feisel

Self-diffusion in pure crystalline solids has been described through extension of the Cohen and Tum-hull volume -fluctuation model originally proposed for diffusion in simple liquids. It is shown, for a number of crystalline solids, that the self-diffusion coefficient, D, obeys the relationship where a is the lattice spacing, v the Debye frequency, Z&apos; the lattice-volume fluctuation per atom required for a diffusion jump, and (?V/Vo) the relative increase in the lattice volume resulting from thermal expansion between O°K and the temperature under consideration. The calculated value of Z&apos; is dependent upon the difiusion mechanism and the lattice geometry. ThE need for an increased understanding of mass-transport processes in crystalline solids has resulted in much research to determine rates of self-diffusion.&apos; For several metals (e.g., copper, silver, and iron), the experimental values of the self-diffusion coefficient, D, have been determined over a large interval of temperature and the accuracy of D has been investigated through repeated experiments. Also, a number of empirical and theoretical diffusion studies have established a rational basis for understanding the D values for the different elements.2"6 The empirical diffusion analysis by Sherby and simnad6 supplied the main stimulus for the present study. Sherby and Simnad, reviewing the self-diffusion data for a substantial number of pure crystalline solids, suggested that sufficient data were available to establish with some certainty the apparent intrinsic material properties which influence D. Without explicit regard for any mechanism of diffusion, these investigators obtained an empirical relationship for D which correlated the self- diffusion coefficient for each element with the melting temperature, crystal structure, and valence of the particular element. Their analysis is only unsatisfactory in that the effect on D of crystal structure is not very clear and the valence to be assigned to an element is not always straightforward. The present study is an attempt, from a very different viewpoint from that of Sherby and Simnad, to establish a basis for understanding the self-diffusion coefficients for crystalline solids. This analysis was undertaken for the purpose of developing a general expression for D which would explicitly depend on the mechanism of diffusion. The main result of the study is that diffusion in crystalline solids may be described in terms of a volume-fluctuation model which was originally proposed by Cohen and Turnbull7 to describe diffusion in simple liquids. The model appears to be useful for predicting self-diffusion coefficients in crystals. The following sections describe the volume-fluctuation model for diffusion, the application of this model to crystals, and the resultant agreement with experimental data. 1) THE VOLUME-FLUCTUATION MODEL FOR DIFFUSION Cohen and Turnbull7&apos;8 developed their model for liquid self-diffusivity for the purpose of describing certain properties of liquids, glasses, and the liquid-glass transition. A hard-sphere model for the liquid structure is used. In this model, the size of a spherical molecule or atom is fixed for all temperatures by the interatomic spacing at the absolute zero of temperature. At any temperature above O°K, the atom is viewed as being contained within a larger spherical cage defined by the interatomic spacing of the atoms at that temperature. A random distribution of varying cage sizes is assumed to exist in the liquid. An individual diffusion jump occurs when the free volume of an atom (the volume of the cage containing the atom minus the volume of the atom) is large enough for the atom to jump out of its cage. With this physical picture of diffusion in liquids, Cohen and Turnbull derive the following equation for self-diffusivity: D=Doe-yv*/vf [1] where Do is the product of three factors which are the diffusion-path geometry, the diffusion-jump distance, and the velocity of the diffusing atom, v*

Jan 1, 1964

By D. F. Gibbons

THIS investigation was undertaken in order to gain further information on the mechanism of plastic deformation of iron at temperatures between room temperature and 77.2°K, and also to contribute to our understanding of the low temperature brittleness phenomenon that occurs in both the tensile and impact tests. It was decided to study as pure an iron as possible and to use the tensile test in order to simplify the problem as much as possible. Two series of iron were used throughout the investigation: iron A, obtained from the National Research Corp. and supplied as gas-free, high purity iron; and iron B, obtained from Fast&apos; and produced by melting iron under purified hydrogen. Typical analyses of samples of both irons, after fabrication, are given in Table I. The main difference in composition of these irons is in their nickel and oxygen contents. Nickel has a very large solid solubility in iron. However, oxygen has an extremely small solid solubility. An attempt was made to reduce the oxygen content still further by remelting under purified hydrogen. This was successful in reducing the oxygen content to -0.0006 pct. However, no results on tests of this iron are included, since difficulty was encountered in fabricating the ingot. Wire specimens 1 mm in diameter were used for the investigation. The wires were produced from the ingots, as supplied, by cold rolling and swaging, with intermediate vacuum anneals at 700°C. Care was taken to reduce preferred orientation in the wires to a minimum by keeping the percentage of reduction in area between anneals of 30 to 40 pct. X-ray transmission photographs showed no indication of preferred orientation. The final grain size of iron A was 20 to 24 grains per linear mm and of iron B, 16 to 18 grains per linear mm. All specimens were tested in the decarburized and denitrided condition unless otherwise stated. The procedure was to pass hydrogen, saturated with water vapor at 26oC, over the specimens at 730°C for 2 hr. The specimens were quenched in iced water and then annealed in a vacuum of - 5x10-6 mm Hg for one day at 560°C to remove hydrogen. Higher temperatures were used for the vacuum anneal but this temperature was found to be quite satisfactory in removing hydrogen. The specimens were slow-cooled after the vacuum anneal. Where it is stated that the specimens were carburized, the specimens were given an identical decarburizing treatment and then carburized by passing hydrogen, saturated with pure n-heptane vapor at 0°C, over the specimens at 730°C. The specimens were then homogenized at 730°C for 2 hr in dry hydrogen. After the carburizing treatment the specimens were given the same vacuum anneal as for the decarburized specimens. The carbon content was determined from the maximum value of the internal friction carbon peak.2 Apparatus Fig. 1 shows a diagram of the tensile apparatus, with half the cooling coil removed. The cooling coil enabled temperatures from 200" to 77.2oK to be obtained. The apparatus was designed to fit a standard Tinius Olsen Universal tensile machine. The apparatus consisted of the rigid plate A which carried two carefully machined hooks H. These hooks attached the plate firmly to the moving crosshead of the tensile machine. The lower grip B was rigidly suspended from the plate A by three stainless steel rods. The upper grip C was joined to the upper grip of the tensile machine by the stainless steel rod E. The lower part of the apparatus was surrounded by a Dewar vessel, which was made a sliding fit inside the brass collar D. The specimen was held in a clamp which fitted into the grip, forming a ball and socket joint (see inset a). This was to attain as nearly pure

Jan 1, 1954

By Herty, C. H.

One of the numerous requirements of many grades of present- day steel is that the steel shall be free from non-metallic inclusions. These inclusions may be composed of oxides, sulphides, complex oxy- sulphides, and nitrides, which enter the steel with the furnace charge, result from sulphur absorption from the furnace gases, or are formed in the steel during the deoxidation process. Although few&apos; data are available which indicate in any quantitative manner the specific effects of inclusions in steel, there is a large mass of circumstantial evidence which points to the advisability of producing steel free from these impurities for many purposes. At the present time there is a growing feeling among metallurgists that non-metallic inclusions should be divided into two distinct types: (I) those readily visible under the microscope at ordinary magnifications; and (2) those in colloidal suspension or in solid solution. Both types are profoundly influenced by the character of the charge, the manipulation of the furnace slag, and the method of deoxidation. The work described in this bulletin deals primarily with inclusions visible under the microscope at ordinary magnifications, but the steels made by the various methods of deoxidation are being used LO study certain effects which may be ascribed to the second classification, named above. This latter work will be the subject of further bulletins on the effect of deoxidation practice on the physical properties of the steels involved.

Jan 1, 1957

By Frank L. Nason

(New York meeting, February, 1912) IN the year 1904 an eminent Swedish geologist prepared a report on the iron-ore reserves of the world. His estimates follow: Countries. Tons. United States, 1,100,000,000 Great Britain, . 1,000,000,000 Germany, 2,200, 000, 000 Spain, 500,000,000 Russia and Finland, 1,500,000,000 France, 1.500, 000, 000 Sweden, . 1,000,000,000 Austria-Hungary, . 1,000,000,000 Other countries, 1,200,000,000 Total, . 10,000, 000, 000 The iron-ore allotted to the United States by the Swedish geologist is barely sufficient to last 20 years at the present rate of consumption. On the other hand (according to Edwin C. Eckel,1 from whom the above and following statistics are quoted), there is hardly need for worry on the part of our iron industries for the, next two centuries or more. Upon the basis of careful work by the U. S. Geological Survey, in which Mr. Eckel has taken an important part, the following estimates arc definitely, but by no means finally, given for the United States District. Tons. Lake Superior District, . . 1,500,000,000 to 2,000,000,000 Alabama, red hematite. . . 1,000,000,000 brown hematite, 725,000,000 Georgia, red hematite, 200,000,000 brown hematite, 125,000,000 Tennessee red hematite, . 6110,000,000 I brown hematite, 225,000,000 Virginia., red hematite, 50,000,000 brown hematite, 300,000,000 Total, . . 4,725,000,000 to :5,225,000,000

Jul 1, 1912

By Finney, W. R.

MUCH has been said and written of the "Big Inch," of the terrific obstacles encountered in its construction, of the colorful and tough men engaged in its building, but little has been publicized of the engineering and economic problems behind the scenes. Long before Pearl Harbor it was apparent to the petroleum industry that a critical oil shortage could be expected along the Atlantic seaboard, owing to delay in tanker deliveries as a result of convoy movements, and to allocation of vessels for foreign shipments. This area, with a normal consumption of approximately 1,800,000 barrels per day of oil and products, was almost entirely supplied by tanker. Pipe lines supplied an average of only 20,000 barrels per day in 1939, 40,300 barrels per day in 1940, and 55,000 barrels per day in 1941. A small amount of oil and products was also delivered via barge.

Jan 1, 1943

By E. H. Crabtree

This paper traces the experimental and pilot plant work completed by the authors since 1939 including the various methods which have been developed in applying coarse activated carbon to cyanidation. The methods and results developed by the authors in desorbing gold and silver from carbons are given and the possibilities for the re-use of the desorbed carbons are discussed

Jan 1, 1950

By Ogden Tweto

The classes of ore deposits in the mountain province of Colorado that have been the most productive in the past and that offer the greatest promise for the future are: (1) disseminated or stockwork molybdenum deposits associated with Tertiary stocks; (2) combination precious- and base-metal veins in Tertiary volcanic rocks; and (3) base-metal replacement deposits and veins in Paleozoic sedimentary rocks. Veins in Precambrian rocks, including precious metal-bearing sulfide veins, gold-silver telluride veins, and tungsten veins, have been mined extensively in the past, but their aggregate output has been far subordinate to that of the groups named above, and the outlook for major output from them in the future is poor. Principal ore deposits of south-central Wyoming are sedimentary iron ores of Precambrian age and uranium deposits in Tertiary sedimentary rocks. Precambrian deposits of several kinds are scattered through the mountains of both states. The most promising of these, based on present indications, are vanadiferous titaniferous magnetite in southern Wyoming and southwestern Colorado and thorium-niobium rare-earth deposits associated with alkalic intrusive complexes in Colorado. Most of the mining districts of Colorado are in the Colorado mineral belt, a generally narrow but somewhat irregular belt that extends northeastward across the north-trending mountain ranges and the north-northwest trending geologic grain of the state. The belt is characterized by intrusive rocks of Laramide and younger age and by ore deposits, and it occupies environments ranging from Precambrian crystalline rocks through Paleozoic and Mesozoic sedimentary rocks to Tertiary volcanic rocks. Two ages of intrusion and ore deposition recently have been recognized in the mineral belt. One is Laramide (late Cretaceous and early Tertiary), and the other is Oligocene. As interpreted herein, the major replacement deposits and most of the sulfide vein deposits in Precambrian and sedimentary rocks are Laramide in age, and the molybdenum deposits, the tungsten and the gold telluride veins in Precambrian rocks, and the precious- and base-metal veins in volcanic rocks are Oligocene in age. In general, the Laramide deposits are mesothermal in aspect, and the Oligocene deposits are principally epithermal. The existence of two mineralization stages, in considerable part characterized by different suites of metals, has many applications in exploration.

Jan 1, 1968

By Henry G. Granger

NOTHING in this paper is to be understood as even suggesting a moment&apos;s suspension of the splendid work now going forward on the Isthmus of Panama, except so far as it is related to the proposed locks. All the work already done, and all material purchased or ordered, would be available for the plan herein proposed. The situation and the problem concerned may be summarized as. follows : The scheme of a lock-canal through the Isthmus of Panama was adopted, as is well known, on two principal grounds-namely, the greater expense of a sea-level canal, and the longer time required for its construction. Of these, the latter is believed to have been the more influential. But further developments have diminished the weight of both, so that a reconsideration of the question is warranted. It is the purpose of this paper to advocate such a reconsideration-emphasizing the importance of certain objections to the lock-canal not mentioned or not duly appreciated in the report of those members of the International Board of Consulting Engineers who favored this form; showing the nature and bearing of the new facts developed; and, finally, proposing a combination of well-known methods and apparatus, which would, in my judgment, effect the construction of a sea-level canal in less time, and perhaps at no greater cost, than will be required for the remaining work on the lock-canal. I. OBJECTIONS TO A LOCK-CANAL. 1. Earthquakes. Two centuries ago Panama is said to have been destroyed by an earthquake. In 1882 a rather violent earthquake was felt at the southern end of the Isthmus. In 1898 I felt a slight shock near the present border-line of Colombia. In 1900 I felt three shocks at Quibdo, the head of navigation of the

Jan 1, 1909

By J. C. Boswell, J. D. Crawford

IN addition to its base-metal and coal mining operations, the United States Smelting Refining and Mining Company has, for the past quarter century, been one of the few large American mining companies interested in dredging. Its activities in this field are confined to gold, and to Alaska, but it is the largest operator in that territory, with twelve huge dredges available to work during the summer on the frozen ancient beach sands at Nome and the gravels of Fairbanks. These operations will be described separately.

Jan 1, 1948

By T. B. Nolan, R. N. Hunt

In terms of present metal prices, analysis of extant records of the Eureka district indicate past production of the magnitude of $200,000,000 in recovered silver, lead, and gold. Production to date has been thoroughly oxidized ore from massive replacements, fissures, manta, and pipe-like bodies-in large part from the massive Eldorado (middle Cambrian) and Hamburg (middle to late Cambrian) dolomite horizons. In the productive area of about 6 square miles carbonate rocks comprise 80 per cent of the section, which includes early Cambrian to late Ordovician horizons. Four-fifths or more of the district's production came from a block of Eldorado dolomite in Ruby Hill that was moved in over younger horizons on strands of a regional thrust fault. The lower 500 to 600 feet of the block was much fractured and brecciated and became host to the ores. The Ruby Hill fault, a late normal fault, limits the Ruby Hill block of dolomite on the north for its entire length of nearly a mile and terminates the downward extent and exploitation of its ores. It introduced an hiatus of some 40 years in the district's development. Drilling of the past 20-odd years, followed by underground work, has now exposed the down-faulted extension of the Ruby Hill block of Eldorado dolomite and its contained ores, dropped 1800 feet in a dip shift to depths beneath the surface of 2000 to 3000 feet. The ores at depth are the sulfide counterpart of those mined in early years on the footwall side of the fault. The ores of the district may be attributed to the same source as the intrusive quartz diorite outcropping in a limited way south of Ruby Hill but found at depth elsewhere in drill holes. The long north-south axis of the district, its anticlinal structure, its major faults, and the distribution of the intrusives and, in their relation to the surface, the ores themselves, all suggest that erosion has not cut deep enough to expose the extent of intrusives and the ores consequent upon them.

Jan 1, 1968

By EDWARAD A. SIVEDENBORMG

REPORTS have been made at different times on the progress of water encroachment in the Frontier sands in the Salt. Creek oil field, Natrona county, Wyoming. All previous reports have, -however, been largely based on the position of water in the sands as determined by various physical tests. Subsequent information has been secured through a preliminary investigation of the porosity, grain size and degree of saturation of the Frontier sands. Also, a closer differentiation has been made between the waters encountered incident to the production of oil by means of chemical analysis. In view of the more recent developments there has been a need of a water encroachment map of the first Wall Creek based on a field survey and additional information acquired since the water encroachment map of the sand of 1926, by J. S. Ross and E. W. Henderson, petroleum engineers of the U. S. Geological Survey. The present report is confined to a study of the first Wall Creek sand and was written in connection with the preparation of the map, showing water encroachment in this sand. The first Wall Creek sand was the discovery sand in the field, the first well having been drilled in 1908. Its thickness averages 120 ft. and, varies between 90 and 160 ft. The sand is in the Colorado group of the Upper Cretaceous series and is further considered as a part of the Frontier formation found in other parts of Wyoming.

Jan 1, 1930

By Maurice Ewing, J. A. Peoples, J. W. Peoples, A. P. Craby

The purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data summarized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the opportunity for checking results so thoroughly is given. In the second place, the fact that recent commentatorsl,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1921, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected &apos;his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By Maurice Ewing, A. P. Craby, J. W. Peoples, J. A. Peoples

The purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data summarized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the opportunity for checking results so thoroughly is given. In the second place, the fact that recent commentatorsl,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1921, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected &apos;his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By C. A. Stetefeldt

FoR the convenience of those who do not care to enter into the details of this long essay, I begin with a summary of the most important results it presents. The extraction of silver by the lixiviation-process from ores which have been subjected to a chloridizing-roasting, is based upon the fact that silver chloride is easily soluble in solutions of sodium or calcium hyposulphite, and that silver is precipitated from such solutions by an alkaline sulphide, with regeneration of the hyposulphite salts. In case the ore contains lead a large portion of the latter is and dissolved, lead sulphate being soluble in hyposulphite solutions. If, at the same time, copper is present, the sulphides precipitated from the solution, contain silver, copper, and lead, a combination of metals not desirable for subsequent treatment. Mr. E. H. Russell, of Park City, Utah, is the inventor and the patentee in the United States and several foreign countries of a new lixiviation-process, based upon the chemical facts discussed in this paper. Mr. Russell has discovered that lead can be completely separated from a sodium hyposulphite solution, as lead carbonate, by sodium carbonate or purified soda-ash, without precipitating any copper or silver. After decanting the solution from the lead carbonate, silver and copper are obtained from it in the usual way. This method of separating lead prohibits the use of calcium poly-sulphide as a precipitant for the sulphides, because any calcium entering the regenerated lixiviationsolution would also be precipitated as a carbonate with the lead by soda-ash. Hence, a sodium sulphide must be employed. A full investigation has demonstrated that this is by no means detrimental. Sodium sulphide and hyposulphite are more advantageously used in the lixiviation-process than the corresponding calcium-salts. Another defect in the lixiviation-process consisted in the necessity of a very perfect chlorination of the silver in the ore, because silver in

Jan 1, 1885

Jan 1, 1901