Search Documents

By T. A. Rickard

Our Transactions contain two notable papers descriptive of the stamp-milling practice of the Black Hills and of Grass Valley, namely, the elaborate and complete treatise of Prof. H. 0. Hofman, on " Gold-Milling in the Black Hills,"" and the paper describing the North Star mill, by E. R. Abadie, its superintendent. Having visited and examined the stampmills of both localities, I venture to offer here such comment as more recent information or a different point of view has suggested.†

Jan 1, 1896

By A. W. Fahrenwald

CELL depth has been for many years a controversial question in a flotation-machine performance. In the impeller type of machine, we are really talking about impeller submergence-i.e., the depth in the pulp at which the impeller is required to produce aeration. THE FLOTATION MACHINE A COMPRESSOR A flotation machine can be considered as an air compressor or blower in which the aeration mechanism takes in air under atmospheric pressure[t] (14.7 lb. per sq. in.) and blows it into the pulp (the pulp being the receiver) against a head of 14.7 plus cell depth in feet times 0.4333 lb. per sq. inch. In commercial machines the impeller is submerged in the pulp to depths ranging from about 2 ft. in the smaller machines to as much as 5 ft. in some of the larger ones. In the 2-ft. cell, the hydrostatic head on the impeller is (2 X 1.25 =) 2.50 ft. (assuming a pulp density of 1.25), equal to (2.50 X 0.4333 =) 1.078 lb. per sq. in. For the 5-ft. cell, the hydrostatic head against which the impeller must make air is (5 X 1.25 X 0.4333 =) 2.708 lb. per sq. inch. In the small 2-ft. machine, the volume reduction is (1.078 [-] 0.147 + 0.01078 =) 6.85 per cent and in the large, 5-ft. machine, the volume reduction is (2.708 [=] 0.147 + 0.02708 =) 15.5 per cent. It is obvious that for unit volume of free air intake the larger machine receives a lesser (8.65 per cent less) volume of aeration* than the smaller machine. The bubbles in escaping from the pulp expand and are greater in volume at the surface than at the moment of their formation in the pulp; 7.33 and 18.4 per cent larger, respectively, in the small and large machines. Just how this situation affects flotation is not known. It is interesting to note, however, that the bubbles are smaller in the zone of the coarsest particles and largest in the upper zones of the finer, more easily suspended mineral particles. It would seem that the relationship might be reversed advantageously. The deep cell is at a greater disadvantage in this respect than the shallow cell. Nothing, however, presumably can be done about this situation. The shallow cell is a partial corrective. Not only does the compression ratio of aeration increase with impeller submergence but the hydrostatic head against which the impeller must operate also increases. THE FLOTATION MACHINE AS A PUMP Since, in impeller machines that rely upon their own operation to produce aeration, pulp passes through the im-

Jan 1, 1946

By Louis A. Carapella, Ralph Hultgren

WHEN F. Heusler1 found in 1898 that certain alloys containing only copper, manganese, and tin were ferromagnetic, the discovery excited a great deal of interest and led to numerous investigations. It was early found that tin could be replaced by aluminum, arsenic, antimony, bismuth, or boron without destroying the ferromagnetic nature of the alloys.2 Copper may also be replaced by silver.3 All these alloys have come to be known as "Heusler alloys." The aluminum alloys apparently were the most magnetic and have been most extensively investigated. However, no agreement has yet been reached as to the source of the ferromagnetism arising from these nonferromagnetic elements. Absence of reliable quantitative data makes speculation hazardous. The value of much of the earlier work was vitiated by lack of necessary precautions against contamination, and by lack of close control of heat-treatment. It was only recently established that in aluminum Heusler alloys" the ferromagnetism arose from a single phase, an ordered body-centered-cubic structure. With modern methods of preparation, heat-treatment, and X-ray examination, it is possible to prepare these alloys without contamination, to heat-treat them intelligently, and to determine what phase or phases are present in the finished sample. In the present investigation, a series of pure alloys in the comparatively neglected copper-manganese-tin system have been prepared, which consist of a single, body-centered-cubic structure (the beta phase) and whose compositions vary within wide limits. The magnetic saturation values of these single-phase alloys have been quantitatively determined, so that considerable data on the effect of composition on the ferromagnetism have been made available. In the course of the investigation some information on the extent of the stability of the beta phase and the nature of phases in adjacent regions of the ternary diagram has been accumulated. Anomalies in earlier data have been explained, and alloys have been prepared that are much more strongly magnetic than any previous Heusler alloys. PREVIOUS WORK In the original work of F. Heusler1 and coworkers,2 a maximum magnetic saturation value of I = 107 was found at the composition Cu6Mn3Sn, while a value for Cu2MnA1 of I = 443 was early measured. Ross and Grays found a second maximum at the composition Cu2MnSn, which was much more magnetic than Heusler's original alloy. F. Heusler6 then reinvestigated the system, confirmed their results,

Jan 1, 1941

By Charles R. Fettke

BefoRe the Drake well on Watson Flats below Titusville, Pa, inaugurated the modern petroleum industry on Aug. 28, 1859, a considerable industry, based on the manufacture of mineral oils through the destructive distillation at relatively low temperatures (750' to 800' F.) of cannel coals and shales in closed, air-tight retorts, had already sprung up in Europe and America because of the increasing cost of animal and vegetable oils and fats and the growing demand for illuminating and lubricating oils. In 1860, eight out of 55 such coal-oil companies in the United States had plants located in Pennsylvania.' Of these, the Lucesco Works, costing $120,000, situated near Kiskiminetas Junction, was the largest operating in the country. It was equipped with 10 revolving 2.5-ton retorts and 16 stills for rectifying the oil, each holding 2000 gal. The total output of crude oil was almost 6000 gal. per day.2 The discovery of an abundant supply of natural petroleum by the Drake and other wells stopped the distillation of coal oil in America. Most of the smaller plants were closed and others were converted into petroleum refineries. At present, in spite of the temporary over-production of petroleum, the coal and oil-shale carbonization industries are again attracting the attention of far-sighted oil companies who realize that the gradual exhaustion of the American petrol-

Jan 1, 1923

By L. D. Jaffe Hollomon, Hollomon John H.

For many steel parts it is desired to obtain the maximum toughness consistent with the strength required by the mechanical design. It is generally recognized that the greatest toughness at any given strength is found in steels having a tempered martensitic structure.' and is virtually independent of the composition of the steel2 (except for carbon). The choice of the composition of a steel for the parts in question should be based, therefore, on hardenability considerations and on manufacturing facility and economy. In a recent paper3 the concept of hardenability was discussed and a somewhat new approach to the problem was suggested. The hardenability was defined in terms of the cooling conditions (speed of cooling) required to avoid the pearlite and the bainite reactions. Since all the alloying elements do not have the same effects on the two reactions, the bainitic and pearl-itic hardenabilities must be considered separately. In order to design a steel for a given part, it is necessary to design a composition that has both sufficient pearlitic and sufficient bainitic hardenability. However, this requirement does not fix the combination of alloying elements to be used; an infinite number of steels would have the required hardenabilities. Other considerations limit the choice. For example, decreasing the carbon content increases the toughness at a given hardness, and for this reason low-carbon steels are often desired. Limitations or requirements of refining, casting, or forming practices often affect the level of some of the alloying elements. Price considerations enter. Frequently, however, it is very desirable to minimize the tendency toward quench-cracking while maintaining the necessary hardenability. This paper is concerned with suggesting a method for choosing compositions that will have the required hardenability together with minimum tendency toward quench-cracking. Quench Cracking Since only the case in which the entire part will transform to martensite in the particular quench employed is being considered, the analysis of the quench-cracking problem is somewhat simplified. Quench-cracking arises from the temperature gradients existing throughout the piece during cooling. Because of these temperature gradients, the contraction arising from the decreasing temperature and the expansion arising from the austenite-martensite reaction do not occur uniformly over the parts, and stresses are set up that tend to cause cracking. The temperature gradients can be reduced by decreasing the severity of quench. This, however, requires that the hardenability be correspondingly increased by increasing the carbon or alloy content. An

Jan 1, 1947

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in ' Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in term of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L slope of energy grade line by s Mass per unit volume of solids by m. Mass Per unit volume of liquid by mi Mass per unit volume of mixture by mm We then have as an expression for the solids load: W = pQmm The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1948

By Paul Giesecke

Since most modern metallurgical plants are operated continuously and on a large scale, successful operation at maximum efficiency demands that an accurate knowledge of the performance at each stage of the process be available at all times. Quantitative analyses provide the most practical process guides, and it is essential to have analytical procedures that combine accuracy and speed. In continuous plant operations, large losses may occur if the time interval between the development of trouble at any stage and its recognition and correction is great. Many metallurgical plants are using rapid colorimetric and spectrochemical methods of analyses for control purposes. So-called "color coppers" may be cited as an example of the colorimetric methods, in contrast with- the routine use of the ultraviolet spectrograph for the analysis of steels.42 By means of this more refined spectrochemical procedure, a complete quantitative analysis of the molten metal is obtained every few minutes. During the past two years the Physics Division and the Ore Dressing Laboratory of the American Cyanamid Company's Stamford Research Laboratories have collaborated in a study of the use of spectrochemical methods for the analysis of various metallurgical products. New methods have been developed, which have proved of practical value in plant operation. The following pages give a general review of the principles of spectrochemical methods and also the details of several specific analyses. Principles of Spectrochemical Analysis In general, it can be said that a visible light spectrochemical analysis can be performed for any ion or molecule that is naturally colored, or that can be made to react with another to produce a colored salt or complex. Whereas transmission measurements in the ultraviolet and infrared portions of the spectrum are most useful for the analysis of organic molecules, * visible light measurements are of particular value for metal salts. Such elements as copper, manganese, cobalt, nickel, iron, molybdenum, vanadium, chromium, phosphorus, mercury, zinc, lead, and a great many others, can now be determined with a high degree of sensitivity, accuracy and dispatch. From the simplest of qualitative determinations, color analyses have been improved to such an extent that, at the present time, through the use of recording spectrophotometers, hundreds of accurate quantitative analyses can be performed by a single analyst during an 8-hr. day after the standardization curves have been established for the ions to be determined.

Jan 1, 1947

By Harry L. McNeill

The Selective Media Process was developed by the author in a laboratory provided by The Steams-Roger Manufacturing Co. It is the outcome of an investigation into the possibilities of coarse beneficiation by sink and float without using the conventional heavy media. Commercial work to date has been limited to the treatment of minus 3/8-in. iron ore at the Hill Trumbull washing plant of the Cleveland Clifis Iron Co., at Calumet, Minnesota. Two cut away prints of the machine are shown (Figs. I and 2). A rotary conical impeller is mounted within a stationary cone (Fig. 2). This impeller is adjustable vertically by a 12-ton screw jack. The speed of the impeller can be varied from 14 to 32 r.p.m. by the Reeves variable-speed motor pulley mounted on the 7½-hp. motor drive. Attached to the bottom of the stationary cone is the automatic control valve for sink product, actuated by a ¼-hp. gear motor. The sink product is dewatered in a conventional drag driven by a 7½-hp. motor and discharged onto an inclined conveyor containing from 6 to 10 per cent moisture. Two plants are operated at the Hill Trumbull property. All the ore is first treated in a typical washing plant (Fig. 3). when treating "wash ore" a finished concentrate can be produced by the log washers and Akins classifiers, as the separation involves only fine silica (minus 48-mesh) and free iron. However, when "jig ore" is led to the washing plant the coarse

Jan 1, 1947

By E. H. Rose

The question is often pondered whether the flotation process is still an art or has become a science. The fact is that flotation is a science in so many variables that only art can blend them. It is demonstrable that no less than one hundred variables are involved in any flotation operation, most of them immeasurable on a routine basis. The behavior of every one of them is always governed by orderly and unchanging law, as no man can doubt. There is nothing truly indefinite about that behavior; the only indefiniteness is in our knowledge of it, either in general or from hour to hour in the circuit. In dealing with a simultaneous equation in, say, one hundred variables, all not only affecting the outcome to some degree but many influencing each other as well, it is small wonder that the mineral-dressing profession presents a case history of debate and controversial opinion. The statement of the subject of this symposium—a symposium on flotation machines—seems to delimit and define the matters to be considered and at least the general nature of the conclusions sought. Nevertheless, in such a meeting it is not possible to meditate upon all the variables that do in one way or another affect performance of flotation machines. To attempt it would be much like trying to operate a hundred-ring circus. Perverse variables being what they are, one could expect the elephant in ring 36 to squirt a trunkful of water at the tightrope performer in ring 37 to ruin that artist's act, just as our learning to depress pyrite in the early 1920's ruined the act of the formerly faithful old Callows. Honest Disagreements Selective flotation dates from 1922 or 1923, when several plants established their regular flotation operations on a selective basis. Since then, two decades of efforr have gone into the development of better and better flotation machines. Many have come and gone. The competition has simmered down to perhaps a dozen machines, each one of which is staunchly defended by some operators as being the best for their particular jobs, and as scornfully dismissed by at least a few others elsewhere as being positively the poorest for theirs. These disagreements are honest disagreements, honestly arrived at after plenty of sweat. In many a flotation plant, one machine has been tried out against another under conditions as fair as they could possibly be made. Sometimes the results are on a par but more often one machine shows a consistent and unmistakable margin of superiority over the other. In equally honest and enlightened tests, machine A may win over machine B in one place, and machine B over machine A by as great a margin in another. This paper purposes to identify some of the more prominent reasons why this is so,

Jan 1, 1947

By P. H. Cardwell

The effect of various plastics upon the permeability of a sand and the mechanism of their ensuring permeability within the consolidated sand body is discussed. Data are presented on various properties of the plastic materials used in sand consolidation and the effect of temperature and usable temperature ranges are considered. The recovery of petroleum from uncon-solidated sands presents serious production problems, owing to sloughing of the formation. The solution of some of these problems usually has been by mechanical methods.' The ideal way of controlling the sloughing tendencies of these un consolidated formations, however, is to prevent the movement of the individual sand grains by the use of a bonding medium. A step in the desired direction was taken by Irons and Stcesser2 when they taught the use of liquid plastics to produce a consolidating deposit that prevents sloughing. More recently, Wrightsman and Buckley3 proposed a modification of this process. In this use of the liquid plastic, the sand grains become coated and the ensuing hardening of the plastic by polymerization or condensation cements together the sand Particles. Liquid plastics that have been suggested for this Purpose are of the following types: phenolformaldehyde, alkyd resins, vinyl type resins, polystyrene and the acrylic esters. When the flow of fluids through a sand must not be materially reduced, it is essential only to cement together the sand grains with liquid plastic and leave a portion of the interstitial space for fluid flow. TO be assured of obtaining fluid flow through the sand interstices after injection of plastic, it has been necessary in the past to remove the excess plastic from the interstices between the particles before it sets. Wrightsman and Buckley suggest two methods for the removal of the excess plastic from the interstices of the sand: (I) to flush the excess plastic back into the formation, away from the well bore, by use of oil or water; (2) to produce the well before the plastic has set, thereby moving the excess plastic into the well bore. Under certain well conditions it is very difficult to remove the excess plastic from all parts of the formation by either of these methods and leave the formation consolidated with no sections completely sealed. The method* described herein of retaining permeability within a sand body is to use a liquid plastic that upon setting ensures permeability within the consolidated sand body. This cements the sand grains but obviates the need for removing plastic from the interstices of the sand. One of the ways of accomplishing this is to use a liquid plastic that occupies a considerably greater volume than the solidified resin it yields on further polymerization or condensation in situ. In order to be satisfactory, the volume of the plastic while liquid should be at least one and one half times the volume of the solid formed. Preferably,

Jan 1, 1947

By R. H. Wightman

The following paper describes current mining practices of the Riverside Cement Co. at its Crestmore plant, Riverside, California. For a number of years the Riverside Cement Co. obtained its raw materials by surface quarry operations but after these deposits were exhausted for equipment available at that time, the company started underground mining. Mine workings were begun in 1927 to 1930 for the recovery of limestone by block-caving methods. Geology The bed of limestone that is being worked is a metamorphosed and recrystallized limestone, which is generally white in color and from medium to coarsely crystalline. This bed is fissured by water courses that vary from minute cracks to large areas. The bed has also been cracked by intrusions along the footwall and hanging wall. These walls are coarse-grained, gray, quartz granodiorite. The strike of the deposit is north and south and it dips to the east at an angle of approximately 50°. The bed is approximately 1700 ft. long, 270 ft, thick at right angles to the dip at the middle of the deposit and tapers to a thickness of approximately 100 ft. at each end. Mining Methods The mine layout consists of four main levels with elevations as follows: 892 Collar of shaft. 800 Manway level used for ventilation, prospect purposes and as an entrance into the stopes. 700 Mining level where all material is extracted and on which are located the tapping grizzlies. This is the elevation from which all main cutoff stopes and undercutting work is started. 660 Haulage level where the limestone is drawn from transfer raises into the cars and is transported to the tipple by electric locomotives. 633 Level where all water is collected and which keeps the general water table below the working levels. A detailed description of the mine was given in U. S. Bureau of Mines Information Circular No. 6795, in June 1934. Current Block Development The first blocks to be caved were developed very much after the procedure followed in the copper mines of Arizona. This paper covers the ninth block to be caved. with a hard, tough rock like our limestone, it was found that some alterations in the development and control of dm, i, caving were. necessary to secure better crushing effect and provide more safety for such secondary blasting as is required. Sequence of Block Development 1. The fringes of the 800-ft. manway level are driven to confirm the diamond-drill information and serve to determine the final location and development required for the block (Fig. I).

Jan 1, 1946

By A. E. Back

A method is described in which particulate iron, as distinguished from high purity iron powders used in powder metallurgy, is a precipitant for copper contained in dilute solutions. A new precipitation apparatus utilizes particulate iron precipitants to recover copper more efficiently than is possible in a conventional launder precipitation plant. In the search for lower cost methods of recovering copper from mine water, the use of sponge iron or particulate iron (as distinguished from iron powder used in powder metallurgy) as precipitants in place of tin cans, detinned scrap iron, or scrap iron is an intriguing possibility. The relatively faster copper precipitation rate obtained with particulate iron as compared to scrap iron promises economic and processing advantages when, and if, particulate iron becomes competitive cost-wise with available scrap iron. Kennecott has developed a precipitation cone,' see Fig. 1, utilizing various particulate iron precipitants and has demonstrated the process successfully in a prototype at a flow rate of approximately 1000 gal of solution per min. Essentially complete precipitation of copper is obtained, the cone overflow solution is clear and contains no particulate copper, and the iron factor is more favorable than in a conventional launder plant. Initially, sponge iron produced at the Ray Mines Div. Kennecott Copper Corp. for use in a Leach-Precipitation-Flotation process was used in exploratory tests to develop a suitable apparatus to take advantage of the rapid precipitation rate and efficient iron utilization for the recovery of copper from dilute solutions. Here it was demonstrated that, when sponge iron was added to a launder, the particles of iron collected in the bottom of the launder and tended to cement together. This resulted in incomplete precipitation of the copper and inefficient utilization of the iron. Next, sponge iron was suspended in glass columns to study the dynamics of the precipitation reaction. Again it was observed that the particles tended to cement together at low solution flow rates, while at higher flow rates large amounts of the precipitant overflowed the column, resulting in loss of precipitant and an inefficient process. Next, the precipitant was suspended in an inverted cone in a rising column of solution. Dynamic suspension of the solids was maintained at relatively rapid solution flow rates with instantaneous and complete precipitation of copper and with improved iron utilization. The first tests were conducted on a batch basis and it was determined that a dynamically suspended bed of precipitant was necessary for satisfactory operation. More than 99% of the metallic iron could be converted to metallic copper by careful control of the residence time in the cone and copper precipitation was essentially complete, even when the available iron precipitant was almost depleted. Several cones were built, ranging in capacity from 1 to 200 gal of feed solution per min, and finally, a prototype cone was constructed which was 20-ft high

Jan 1, 1968

By John D. Meahin

THE use of digital methods for generating crystallo-graphic data is well-established and many programs are now available. Transmission electron microscopy usually requires a knowledge of the electron diffraction pattern which is obtained by plotting a planar section through reciprocal space. With cubic symmetry these sections are very easily produced, but with hexagonal and lower symmetry systems considerably more labor is involved. Johari and Buchanan1 have written a Fortran program for generating standard projections and along similar lines we have produced a short but completely general program for generating any section through reciprocal space. The required inputs are the lattice parameters and angles for the real crystal. The Miller indices of the direction [U, V, W] parallel to the electron beam are then specified and the program will generate the Miller indices of the plane normals perpendicular to [U, V,, W] up to some specified integer. A subroutine can be inserted to test for forbidden reflections if desired. We have used such routines for fct and hcp crystals. As each permitted index is generated it is printed or punched out and no storage arrays are utilized in the computer. The normal diffraction pattern corresponds to the zero-order Laue zone, but with thin crystals or crystals of large lattice parameters the higher-order Laue zones may contribute to the diffraction pattern. Accordingly the program will generate successive Laue zones and project them onto the zero-order zone. The output of the program first lists the zone axis [C, V, W] and the Laue zone, and then gives a list of permitted reflections and the corresponding XP and YP coordinates of the reciprocal lattice point in angstroms-'. In addition, ZP, the perpendicular distance of the reciprocal lattice point from the (U, V, Ur) plane in reciprocal space is given, as is the reciprocal interplanar spacing. In the case of the zero-order Laue zone ZP is zero. A diffraction spot from the higher-order Laue zones will be very slightly displaced from the computed coordinates as its position in an actual pattern is given by projection along the diffracted beam2 and not along [u, V, w]. For any given electron wavelength this correction could be readily incorporated into the program, but as it only amounts to -1 pct it was decided to leave the program in its most general form, i.e ., a computation of points

Jan 1, 1970

By O. W. Bilharz

Acid mine-water drainage is a serious problem with many mines in the Tri-State zinc and lead mining district. Particularly is this true when large volumes must be considercd in unwatering old mines that have refilled with water which has dissolved the products of oxidation and has become chalybeate in character. The experiences discussed in this paper have to do specifically with the unwatering of a comparatively small area west of the town of Baxter Springs, Kans., where the pumping job was complicated by water of this type and where the extremely high sulphate content particularly effected that phase of mine drainage having to do with stream pollution. Location, Geology and History The Baxter Springs area of the Tri-State mining field is situated just west of the town of Baxter Springs and is a northeasterly extension of the main mineralized zones of the Oklahoma part of the district (Fig I). The mining area is traversed with well defined shear zones which provide easy circulation of ground waters and the ore bodies are found along these shear zones as localized enrichments wherever the structural conditions are favorable (Fig 2). The ore-bearing strata is Mississippian with an overlain capping of shale of Penn- sylvanian age. This shale strata carries much pyrite and marcasite at its base and undoubtedly was a contributing factor to the subsequent high iron content of the water. The area originally contained a sulphide water which discharged as an artesian flow in springs within the town and gave Baxter Springs its name. These springs were famed for many years for their mineral water. This original sulphide water was first removed about 1917 and active mining was carried on west of the town during subsequent high metal price periods. Many small mines were opened, with each localized enrichment becoming a separate mine. During the depression mining ceased and all mines in the west Baxter area were allowed to flood. No serious effort was made to again unwater until higher prices caused from the demand for metal for World War II once more focused attention 011 this part of the field. Original Mining Results in Oxidation As plans for unwatering progressed, it soon developed that the mine-water pools had become strongly acid in character and carried large amounts of sulphates in solution. This occurred in the following way. When the original sulphide water was removed, shafts sunk, and mining carried on over a number of years, ferrous sulphate was formed by the spontaneous oxidation of the pyrite beds in contact with air admitted through churn-drill holes and mine openillgs. These products of oxidation can be seen today in the old mines of the district as crusts of crystalline sulphates

Jan 1, 1949

By Harry L. McNeill

The Selective Media Process was developed by the author in a laboratory provided by The Steams-Roger Manufacturing Co. It is the outcome of an investigation into the possibilities of coarse beneficiation by sink and float without using the conventional heavy media. Commercial work to date has been limited to the treatment of minus 3/8-in. iron ore at the Hill Trumbull washing plant of the Cleveland Clifis Iron Co., at Calumet, Minnesota. Two cut away prints of the machine are shown (Figs. I and 2). A rotary conical impeller is mounted within a stationary cone (Fig. 2). This impeller is adjustable vertically by a 12-ton screw jack. The speed of the impeller can be varied from 14 to 32 r.p.m. by the Reeves variable-speed motor pulley mounted on the 7½-hp. motor drive. Attached to the bottom of the stationary cone is the automatic control valve for sink product, actuated by a ¼-hp. gear motor. The sink product is dewatered in a conventional drag driven by a 7½-hp. motor and discharged onto an inclined conveyor containing from 6 to 10 per cent moisture. Two plants are operated at the Hill Trumbull property. All the ore is first treated in a typical washing plant (Fig. 3). when treating "wash ore" a finished concentrate can be produced by the log washers and Akins classifiers, as the separation involves only fine silica (minus 48-mesh) and free iron. However, when "jig ore" is led to the washing plant the coarse

Jan 1, 1947

By R. L. Templin

In treating a cast metal by any working process such as rolling, drawing or forging, variations in the conditions present in the remelting, casting, chilling and preheating of the initial ingot will certainly have some effect on the physical properties of the final product. In considering the effects of cold working on the physical properties of metals, however, it will be assumed that these factors, being controlled according to best practice, will remain constant and therefore may be neglected. Starting with such a uniform metal ingot, the next operation in the production of wrought metal involves hot working by rolling, forging or extrusion so as to produce a slab, billet or bloom. This working must be sufficient to produce substantial grain refinement and minimize any defects occurring in the initial ingot. Even such a hot-worked product is not suitable as a starting material for determining the effects of cold working because it contains internal strains analogous to those resulting from cold working. It is necessary, therefore, to supplement the hot working with a considerable amount of cold working, followed by a proper annealing in order to obtain a material suitable for use in defining the effects of cold working on the physical properties of a metal. That is, if the effects of cold working are to be evaluated accurately it is necessary to have other effects at least constant if not absent. Such material, unfortunately, cannot always be obtained in commercial practice but the requirements just indicated certainly represent the desired goal; this goal has been attained in the treatment of some metals, one being aluminum. Factors That Must Be Considered Simultaneously with Cold Working So many other factors affect the physical properties of a metal that it is necessary to consider these factors simultaneously with cold working; their effects vary in magnitude with the amount of cold work present. The most important of these factors are: (I) chemical composition, (2) structure, (3) temperature of working, (4) character of working, (5) rate of working, and (6) methods used for measuring results. For

Jan 1, 1930

By L. R. Ingersoll, James Fisher, Harry Vivian

The copper mines of the Keweenaw Peninsula in northern Michigan have long been of interest in connection with deep earth-temperature measurements. The extraordinary low geothermal gradient of l° F. in 223.7 ft. announced by Agassiz1 as a result of measurements dating from 1886, although later2 stated as in error, served to focus attention on this region as one offering, because of the great depth of the mines, unusual opportunity along this line. Lane,3 Van Orstrand4 and others have made valuable contributions to this study. Fresh opportunities afforded by the constant deepening of the mines, improvements in the accuracy and reliability of temperature-measuring instruments together with increasing knowledge of the heat conductivities and specific heats of the rocks, led the Michigan College of Mining and Technology in cooperation with some of the mining companies to renew work on this problem. It is planned eventually to complete a survey which will make use of the favorable opportunities for deep rock-temperature measurements presented in these mines. This survey should include the determination of a depth-temperature gradient in both conglomerate and arnygdaloid mines, and also the variations in temperature at the same depth in different geological formations. The first problem has a direct bearing on the question of providing equipment for necessary ventilation with increased depth. The second may show that a relation exists between the natural rock temperature and the mineral content of the formation. The measurements in all cases are to be guided by heat conduction considerations, to the end that they may represent as closely as possible

Jan 1, 1934

By Glen R. Neighbors, Sylvan Cromer

HIGH subsurface temperatures and pressures are making cementing operations more difficult as deeper producing horizons are being sought. Recorded bottom-hole temperatures above 200°F. and pressures in excess of 12,000 Ib. per sq. in., obtained by combining hydrostatic and pump pressures, are not uncommon. Insufficient time is available for proper placement of standard Portland cement, because of the shortened setting time produced by these excessive temperatures and pressures, therefore special types of cements have been developed to overcome these difficulties. From the standpoint of placement, the ideal slurry would be one that would remain fluid long enough to be placed, then harden rapidly, so that there would be a limited amount of contamination and the well could be placed on production in a minimum of time. It is highly desirable, therefore, that some method be devised to measure accurately the time that any slurry will remain in a fluid state while being pumped into the well. To study the effect of elevated temperature and pressure on fluidity, the authors have developed the pressure-type consistometer (Figs. I and 2) described below, and are presenting data obtained with it, using slurries of both quick-setting and slow-setting cements. Studies were made over a temperature range from 110° to 270°F., and a pressure range from atmospheric to 3000 lb. per sq. inch. APPARATUS The fluidity of cement slurries at atmospheric pressure is usually determined with the Halliburton consistometer1 or the Thickening Time Tester.2 These instruments are similar, in many respects, to an ordinary ice-cream freezer. The slurry to be tested is placed in a container that is rotated at a constant speed with an electric motor. Constant temperature is maintained by surrounding the container with a thermostatically controlled bath. The torque on the paddles, which is proportional to the force needed to shear the slurry, is indicated on a scale. The Halliburton instrument is calibrated from 0 to 100 poises against fluids of known viscosity. To permit direct correlation of observed elevated pressure data with those published at atmospheric pressure, the authors' designs of the slurry container, paddle, and torque indicator closely resemble those used on the Halliburton instrument. Duplicate results may be obtained at atmospheric pressure in either instrument. Instead of the atmospheric constant-temperature bath, one was built from a high-pressure steel bull plug. A Uni-Bolt union equipped with a blanking plug serves as the top, permiting the instrument to be opened or closed in less than one minute. The slurry container is built from Shelby steel tubing. A wrench socket welded to the bottom of the container engages a hexagonal nut on the top of the steel shaft that rotates it. This acts as a universal

Jan 1, 1941

Report of the Secretary GENTLEMEN Herewith are transmitted reports from the Treasurer and of the principal standing committees of the Institute. To these special reports members are referred for details as to the year's work. Despite the unfavorable business conditions obtaining throughout the year, the Institute was able to carry on its various activities without curtailment and without drawing on the surplus accumulated through previous years. In fact, small additions were made to the Life Membership and various other funds. It is highly desirable that such additions should continue to be made, especially to the Life Membership fund, for reasons reported last year. At present, money must be used from current receipts in order to enable the Institute to fulfill its obligations to those who on joining the organization commuted their dues by a single payment. In addition, with the passage of years the number increases of those who have paid dues forty years or more and who, by reason of age or disability, are unable longer to practise their profession. These men have supported the Institute through their active professional life and it would be a pity to lose them as members through resignation or for failure to keep up their dues. In accordance with the By-laws the Board has authority to advance such members, on application, to the Honor Roll of Senior Members and to relieve them from further payment of dues. It has been the policy of the Board to do this liberally, but to keep up this, as well as to meet other obligations, it is necessary for money to be provided. It has been estimated by the Treasurer that nearly $50,000 additional should be placed in the Life Membership fund as soon as possible to meet these obligations without using current income and to that end it is necessary, not only to avoid running behind currently but to earn, if possible, some surplus each year. The small amount transferred to the Life Membership fund from surplus this year was, as a matter of fact, made possible by certain members paying personally bills that were properly chargeable to the Treasury. Such generosity is common among those active in Institute work and probably no year would have closed with a surplus except for it.

Jan 1, 1929

By S. K. Nowak

The lithium solubility limit in solid aluminum was determined by the use of micro-graphic techniques. The solubility limit thus established was shown to be a true equilibrium by checking the reversibility of AlLi phase precipitation and dissolution around the equilibrium temperature. The experimental results fit a straight line by plotting log N(LI) against 1/T. The metallurgical reasons explaining the lack of agreement among previous investigations are discussed. THE solubility limit of lithium in solid aluminum was determined by Shamray and Saldau1 by micrography and by Grube et al.' and also Voss-Kiihler- by measurement of electrical resistivity. Since the addition of lithium induces extremely small changes in the aluminum lattice, X-ray techniques could not be employed for this purpose; in fact, the addition of lithium does not cause an expansion of the lattice as might be expected from a consideration of atomic radii, but causes a small contraction from 4.040 to 4.037A3, 4 when the solvent aluminum is saturated with this element. An analysis of the results from previous investiga-tions'" shows that with improvement of investigation techniques the solubility limit tends toward a lower lithium content. Again, some of the author's own experimental results on the action of atomic hydrogen on A1-Li alloys seemed to indicate that the solubility of lithium should be much lower, i.e., about 0.3 pet at 300°C: instead of 1.15 pet, the lowest published value.4 For the foregoing reasons it was decided to investigate this problem. The aluminum and the lithium used for this purpose were of the highest purity. The lithium solubility limit was determined by metallographic techniques, in particular by the use of a reagent especially developed for the purpose of revealing the AlLi phase. The solubility limit thus determined was shown to be a true equilibrium by checking the reversibility of AlLi phase dissolution and precipitation around the equilibrium temperature. All of the experimental work was carried out in 1951 at the Centre d'Etudes de Chimie Metallur-gique at Vitry, France, under the direction of Georges Chaudron.

Jan 1, 1957