Search Documents

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.' It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anortho-site, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagio-clase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout.' Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized.V he bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15". The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1953

By David P. Shoemaker, Clara B. Shoemaker

It has been shown for an important class of complex transition intermetallic compounds (a, P, R, 6, and p phases) characterized by "normal" coordination [CN12 (icosahedral), CN14, CN15, CN16/ that interatomic distances nay be calculated to a good approximation as the sum of characteristic atomic radii. Two radii, one for major ligands and one for minor ligmds, are specified for each atom, except in the case of CN12 where only a miaaor-ligand radius is specified. The same appears to be true of transition-metal phases of simpler struc-ture: Laves phases (CN12, CN16), and p-tungsten phases (CN12, CN14). In the case of known examples of the more complex phases, a simple rule is given which specifies these radii. However, only a fraction of the known examples of the simpler phases obey this rule closely. To include the latter phases the rule may be modified by considering the radii as linear functions of the weighted average of the Pauling CN12 radii of the two kinds of atonzs, with the radii weighted according to the over-all chemical composition of the alloy. With very few exceptions interatomic distances for both tlze complex and the simpler transition phases can b$ predicted with this modified rule to within 0.06A. ManY intermetallic compounds are known of composition A,By, in which A is a transition element to the left of the manganese column in the periodic table and B is a transition element in or to the right of it. Frequently the coordination numbers (CN) found in these compounds are CN12 (icosahedral), CN14, CN15, and CN16 (called "normal" coordinations by Frank and Kasperl). Well-known examples are the cubic and hexagonal Laves phases which have CN12 and CN16, and the 0-tungsten (CrsO) phases which have CN12 and CN14. In the more complicated (often ternary) phases, such as the a phase,2 the Beck phases p3 and R~, the 6 phase,5 and the p p atoms occur with CN12, CN14, CN15, and (except for a) CN16; in many cases several crystallographically independent atoms of one particular CN occur in the asymmetric unit. A large number of independent interatomic distances are found in these complicated phases, varying from 20 in the a phase to 94 in the 6 phase. These distances show a large spread; they vary, for example, from 2.358 to 3.278A in the 6 phase. In our analysis of these distances we found that in each of these compounds every atomic position can be characterized by either one or two radii. The CN12 positions are characterized by a single radius, The higher coordinated positions are characterized by two radii, namely: the CN14 positions by 4 in the direction of the twelve "5-coordinated" ligands3 (called 'minor" by Frank and Kasperl) and by r:, in the direction of the two "6-coordi-nated" ligands (called "major" by Frank and Kasper); the CN15 positions by r15 for the twelve minor and r:, for the three major ligands; the CN16 positions by rlE for the twelve minor and r:, for the four major ligands. We have expressed the experimentally determined interatomic distances in observational equations as the sums of the appropriate pairs of these characteristic radii and the value of these radii have been determined by the method of least Squares. Despite their wide range, the interatomic distances could then be predicted by the sums of these atomic radii with an average deviation in any one compound of 0.06A or less. The results are summarized in Table I. Inspection of the radii thus obtained shows that in the structures in Table I the radii (in A) are given to a first approximation by the simple relationship: Where CN is the coordination number (12, 14, 15, or 16), and A = 1 for major ligands and = 0 for minor ligands. The interaLomic distances can be predicted within about 0.1A by sums of these atomic radii. Another phase belonging in this group with CN12, 14, 15, and 16 is the y phase & B7, in which A is molybdenum or tungsten and B is iron or cobalt. Recently the M%C phase has been refinedE and the observed distances also agree well with those calculated with Eq. [I]. (In the original determination of the structure of W6FeV7 the F$(II)-W(II1) distance was erroneously given as 2.84A, but we have recalculated it fro? the published parameters and found it to b? 2.57i4, in good agreement with the value of 2.6A predicted with Eq. [I.].) Many binary transition alloys are known to crystallize with the simpler structures having "nor-

Jan 1, 1964

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.' It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anortho-site, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagio-clase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout.' Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized.V he bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15". The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1953

By J. A. Rowland, C. W. Funk

THIS investigation is a part of the United States Bureau of Mines work in conserving the Nation's resources. The isothermal sections presented were developed as a guide to a comprehensive investigation of the properties and fabricating characteristics of copper-base alloys containing manganese and tin. These alloys are being investigated as possible replacements for the commercial bronzes containing substantial quantities of tin. Development of the isothermal sections has, therefore, been limited to the area between 0 to 20 pct Mn and 0 to 25 pct Sn. Since Heusler1 reported the ferromagnetic properties of the Cu-Mn-Sn alloys in 1903, the system has been the subject of several investigations. These studies were largely concerned with correlation of magnetic properties and crystal structure.2-6 Vero,' however, established the solidus surface of the system, between 20 pct Mn and 40 pct Sn, by thermal and microscopic methods. The a, ß, and y solid solutions were also observed by Vero and reported to extend into the interior of the ternary system. For the present study, the annotated diagram of the Cu-Sn system prepared by Raynor' and the Cu-Mn diagram by Dean and coworkers9 were used as the binary borders of the ternary system. Procedure The metals used in this investigation were electrolytic manganese, washed cathode copper, and three-star tin. The manganese, produced at the Boulder City pilot plant of the Bureau of Mines, had a purity of 99.9 pct; the copper contained less than 0.004 pct Bi and 0.001 pct S; the tin contained 0.070 pct Pb, 0.070 pct Sb, 0.050 pct Fe, and 0.065 pct Si. Heats of 1 lb were melted in alundum crucibles with a 3-kw induction furnace. The heats were chill-cast in iron or copper molds to form 6-in. ingots 3/4 in. in diameter. Molds were washed with graphite or zirconia, depending on the manganese content, and preheated to 150°C. The maximum impurity content of any alloy was 0.03 pct Fe, 0.02 pct Si, and 0.02 pct Al; in most cases, they contained less than half this quantity of any of these impurities. Composition of the alloys and their treatment prior to homogenizing are shown in Fig. 1. Designations adjacent to each composition refer to the heat numbers. With a few exceptions, ingots containing 20 pct Sn or less were hot-swaged. These ingots were swaged, after a 24-hr preheat at 650°C, to obtain a total reduction of 70 pct in cross section. Intermittent reheating was necessary, and reductions were limited to either 0.025 or 0.050 in. in diameter per pass. Selection of a 200-hr homogenizing treatment was based on extensive experiments which indicated that virtual equilibrium was reached after 150 hr. Structures were retained by quenching in water. Grain sizes in the specimens homogenized at 350" and 450°C were generally small. These homogenizing treatments were preceded by a 50-hr anneal at 650°C to facilitate phase identification by increasing the grain size in these specimens. The specimens were furnace-cooled from this temperature to the homogenizing temperature, and the heat treatment was continued for the standard 200-hr period. The homogenized samples were bisected to provide an internal section for metallographic examination. Optimum definition of the microstructure was obtained by successive polishing and etching. Quarter-strength ASTM copper reagent No. 13 gave the most satisfactory results.10 Filings from interior sections of the samples were used for diffraction studies. These filings were annealed in evacuated glass tubes at homogenizing temperatures for periods exceeding 50 hr and quenched in water. During this treatment the manganese content was reduced by significant amounts, probably by vaporization. This change in composition was considered in applying the diffraction data, which were used only as a means of identifying phases where the data were consistent with the metallographic evidence. Phase Identification The a solid solution is readily distinguished by the copper-colored, twinned, polyhedral grains, as shown in Fig. 2, and a face-centered cubic X-ray pattern. Tukon indentations, using a 25-g load, indicate a Knoop hardness of 155 for a quenched from 650°C. Using white light developed by a Wratten 78 A filter, the ß grains in etched specimens have a dark brown tint in contrast to the lighter copper-colored grains of the a phase. Knoop hardness values of 284 were obtained for the ß structure in specimens quenched from 650°C. The ß structure was also distinguished from the a phase by its body-centered cubic lattice. The acicular structure appearing in Fig. 3 was evident in several alloys of higher tin content after quenching from either 750' or 650°C. Since a trans-

Jan 1, 1954

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.1 It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anorthosite, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagioclase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout' Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a. zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized! The bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15º. The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1952

By H. E. Cook

The Ising model for the internal energy of a binary alloy has been used to obtain a general equation for the critical resolved shear stress of partially ordered crystals. The equation expresses the stress in terms of the Warren "alphas " and can be used to estimate the variation in strength with order without the assumption, present in the original formulation of this problem in terms of domain size, that order is complete within each domain and that the domains are of ungorm size and shape. In addition, it is the general equation, according to the Ising model, for strengthening by short-range order. Two applications of the equation are considered: One is an estimate of the variation in strength of CkAu with long-range order. The other is an estimate of the variation in strength of FeCo with quench temperature. Reasonable agreement is found with the variations reported in the literature. When the internal energy of an alloy crystal depends upon the distribution of solute, the strength of the crystal will also depend upon it because a portion of the applied stress for plastic deformation will be: where V is the volume of the crystal and E(E) is the energy change associated with the solute redistribution caused by the plastic strain, E. We expect T to equal zero for a crystal having a random arrangement of solute because the arrangement would remain random after plastic deformation. Likewise, we expect it to equal zero when the crystal is perfectly ordered because the motion of paired dislocations found in such crystals does not disrupt order. However, when short-range order exists or when long-range order is incomplete, plastic deformation will decrease the amount of order and additional work, proportional to the ordering energy, will be expended. Fisher' estimated T for crystals having short-range order by assuming an interaction energy between neighboring atoms and estimating the change in the number of unlike neighbors as a dislocation moved through the crystal. (His analysis was limited and several workers2"6 have since given more complete ones.) Fisher minimized the importance of a strengthening mechanism of this type for paired dislocations in a structure having long-range order. ~ottrell,' however, pointed out that T could be appreciable for ordered crystals having antiphase domains. He attributed the strengthening to the increase in surface energy of the domains as they were cut by paired dislocations. Ardley,' in his test of Cottrell's theory, found that r for Cu3Au crystals obeyed the equation: for 1 > t where 1 is the domain size, t is the domain wall thickness, and y is the surface energy of an antiphase boundary. His experiments represent the classic confirmation of the strengthening mechanism proposed by Cottrell. However, the assumptions involved in using Cottrell's theory are valid only for large domain size in CU~AU,~"~ i.e., when Eq. [2] reduces to: For small domains, ~linn~ has questioned Ardley's assumption that order was complete, and, indeed, Stoloff and ~avies" fpnd it incomplete until a size of approximately lOOA was reached. Even when the order within a domain is complete, it is not obvious how one determines the appropriate value for I in a structure where domains vary in size and are irregularly shaped. The purpose of this paper is to estimate T without restrictions upon the degree of order and domain shape. Our major assumption will be the use of a generalization of the model proposed by Bethe" (the Ising model) for the internal energy. This will in fact allow us to combine the theories for strengthening by short-range order and by antiphase domains into a single, general formalism. We will use the results to estimate the variation in strength of Cu3Au crystals with long-range order8 and the variation in flow stress of FeCo crystals with quench temperature.12'13 INTERNAL ENERGY For simplicity, we restrict our considerations to those binary solid solutions which can be described as an arrangement of atoms on a Bravais lattice. An atom site will be indexed by three numbers (PI, pz, p3) determined by the vector: from the origin fixed at atom (0, 0, 0) to the atom site where a', an, and a, are the lattice translation vectors. We write: For the energy of the crystal where pi(p) is the probability (either zero or one) of finding an atom of type i (i = 1, 2) at site (p), which is shorthand for (pl, pz, p3) and pj(p + r) is that for an atom of type j (j = 1, 2) at the site (p + r), which is shorthand for (pl + rl, The coupling parameter, resents the energy associated with the pair Pi(p), Pj(p + r). The crystal is assumed large enough so that surface effects can be neglected; therefore, trans-lational and inversion symmetry require the coupling parameters to obey the relations

Jan 1, 1969

By S. E. Szasz, E. J. Moore, B. F. Whitney

An accurate value of formation water resistivity R, is essential in calculating formation porosity and fluid saturation from electrical well logs. In the cases where R, has not been measured directly, it must be obtained from other data, e.g., the SP curve. This paper deals with another approach: how to calculate R, from the chemical analysis of the formation water. INTRODUCTION It is known that the resistivity of aqueous solutions of pure salts depends on their concentration and on the temperature; the concentrations are given in MPL (mg of solute per liter of solution), or sometimes in ppm (mg of solute per kg of solution): MPL = ppm X specific gravity. Values for different pure salts are available in the literature, but not for solutions of mixtures which are of practical interest. The major component of the dissolved material in almost all formation waters being sodium chloride, it is customary to express the resistivity of formation waters in terms of equivalent sodium chloride concentration, i.e., the concentration of a solution of pure NaCl which has the same resistivity at a given temperature as that of the formation water under consideration. Thus, the problem of calculating R, from the chemical anaylsis can also be stated as how to convert the other constituents of the solute into equivalent NaCl concentration. Salts dissolved in water are at least partly dissociated into ions, and do not conserve their identity. If known amounts of several salts are dissolved in water, the solution does not necessarily contain the same salts in the original proportion, but perhaps some other combination of the ions, along with free ions in solution. This is why the chemical analysis of formation waters is often given in terms of ions, as if all dissolved salts were completely dissociated. Our problem then boils down to how to convert the concentrations of the various ions to equivalent concentrations of Na' and C1-. Dunlap and Hawthorne' have proposed to convert the concentration of all other ions to equivalent Na' and C1-concentrations by means of constant multipliers; e.g., 0.95 for Ca"; 2.0 for Mg"; 0.27 for HCO 3-; 0.5 for SO, -, etc. Their factors were based on measurements made at 68F on 26 formation water samples from the Texas Gulf Coast, ranging in concentration from 1,500 to 75,000 ppm. The Dunlap method is widely used in electric log interpretation, and is often extrapolated beyond its original concentration range. A comparison of R, values calculated by this method and values actually measured on formation water samples has shown large discrepancies, especially at higher concentrations. Therefore, two new methods were developed at Sinclair Oil Corp.'s Tulsa Research Center to calculate equivalent sodium chloride concentration from the chemical analysis of formation water samples. FUNDAMENTAL CONSIDERATIONS The resistivity of a solution, or its reciprocal the conductivity, at a given temperature is determined by the charge, concentration and mobility of the ions actually present. Monovalent ions such as Na' or C1- always carry the same charge. Compounds of polyvalent ions, however. may show incomplete dissociation, e.g., NaSO; + Na' instead of SO,-- + 2Na'. This happens especially in more concentrated solutions. Only very dilute solutions are completely dissociated, as assumed in the chemical analysis report. At higher concentration, the degree of dissociation depends not only on the nature and concentration of the particular salt under consideration but also on the nature and concentrations of the other solutes. Mobility of the ions depends on the viscosity of the solution. It also depends on the degree of hydration of the ions, which in turn is a function of the nature and the charge of the ions and also of the amount of free water available per ion, i.e., the total ionic concentration. The net effect is that the conductivity increases slower than proportional to the concentration, even if a solution contains only one salt such as NaC1, and is different for different salts (Fig. 1). Conductivity can even decline with a further increase in concentration, e.g., if additional salt is little dissociated but ties up some of the free water and/or causes an increase in viscosity. In solutions containing more than one salt, the contribution of one salt to the total conductivity depends not only on the fractional concentration of this same salt, but also on the concentration of all other solutes. A perfect method would give the conductivity or resistivity of a solution as a function of the concentrations of all solutes present. This is so complicated as to be impractical, and a simpler method must be found which is of acceptable accuracy. The Dunlap method, on the other hand. is too simple because it askmes that at any concentration the contrih-

Jan 1, 1967

By John S. Crandall

THE mineral garnet, while ordinarily considered a semiprecious gem stone or a second-grade industrial gem, has also proved itself in the field of industrial abrasives. Its use is well known as a sandpaper grain, and as a sandblasting sand its qualities are rapidly becoming recognized in more and more industries. Production of garnet as an abrasive is confined chiefly to two areas in the United States, North Creek, N. Y., where the Barton Mines Corp. operates, and Emerald Creek, Benewah County, Idaho, where Occurrence: Garnets in the Emerald Creek area occur as disseminated crystals in beds of micaceous schists of the Belt Series, which in this section are estimated to be close to 4000 ft thick. The schists are high in alumina and silica with iron, manganese, and magnesium. Subjection of the original sediments to high temperatures and pressures caused metamorphism to take place with the resultant re-crystallization of high alumina-silica minerals such as garnet, mainly spessartite and almandite varieties, cyanite, sillimanite, chlorite, actinolite, tourmaline, biotite, and muscovite, with minor amounts of ilmenite and magnetite. Quartz is also present in considerable amounts. Fast erosion of the soft mica schists on exposure to weathering has created extensive alluvial deposits containing up to 10 pct garnet having a maximum grain size of 3/16 in. These alluvial sands and gravels are now being treated for the recovery of garnet sands. Treatment: Overburden of 1 to 4 ft must be stripped to expose the garnetiferous gravels. This operation and the subsequent feeding of the gravels to a trommel-screen washing plant are performed by a % yd dragline. The trommel-screen openings are 3/16 in., thus allowing a separation and concentration based on grain size, since over 95 pct of total free garnets are minus 3/16 in. All plus 3/16-in. material is wasted at this point. The minus 3/16-in. material is further concentrated in a sand-drag classifier, where the slimes and silts are washed out and wasted. The sand product from the classifier varies in garnet content from 20 to 60 pct according to the particular section of ground being worked. This sand product is trucked to a jig plant where two sized fractions are made in a trommel-screen. The minus 3/16-in. plus 10-mesh portion is fed to a Pan-American two cell 42-in. jig. The minus 10-mesh portion is treated in a Bendelari three cell 42-in. jig. The jig concentrates are combined to form a 98 pct garnet sand. The jig tailings contain 3 to 5 pct garnet which is mainly flat crystals and chips which will not settle into the jig hutch. Subsequent treatment of these tailings in a scavenger jig followed by drying and electromagnetic separation will, according to tests, reduce the garnet losses in the tailings to something around 1 pct. Jig treatment of this feed approaches ideal as the major portion of the garnet crystals are the natural dodecahedrons and so are, in general, close to spherical. The specific gravity of pure garnet is 4.2, while the next heaviest mineral in the feed is cyanite with a specific gravity of 3.6, then quartz with specific gravity of 2.6. The garnet concentrate is practically free of quartz. The predominant impurity is cyanite which amounts to about 1.5 pct. The rod-like crystals of cyanite appear to up-end in the jig and go into the hutch with the garnets. Some ilmenite and magnetite appear in the concentrate but in very minor amounts. Subsequent washing in a sand-drag classifier removes fine silts and iron oxides. The gravel feed to the washing plant will average 8 pct recoverable garnet content. Concentration ratio in this plant runs about 2.5 to 1. Washing-plant concentrate as fed to the jigs will average 45 pct garnet by weight. Concentration ratio of jigging runs about 2.2 to 1. The garnet concentrate is dried in a rotary oil-fired drier and then fed to vibrating screens in closed circuit with crushing rolls. Practically any grit from 10-mesh down to 150-mesh grain size may be graded to specifications in two 3-deck vibrating screens. The present production, however, is approximately 75 pct No. 36, 15 pct No. 60. and the balance No. 80 and No. 100. Metal-screen cloth is used for sizes down to 36 mesh. From 36 mesh and finer, silk-screen cloth is used since it has less tendency to blind. All garnet sand is bagged in 100 lb self-sealing, sleeve-type paper bags. Practically all shipments are made in carload lots. Car loading is convenient since the plant is in Fernwood on the tracks of a branch line of the Milwaukee railroad. Truck shipments can and are made occasionally.

Jan 1, 1951

By John S. Crandall

THE mineral garnet, while ordinarily considered a semiprecious gem stone or a second-grade industrial gem, has also proved itself in the field of industrial abrasives. Its use is well known as a sandpaper grain, and as a sandblasting sand its qualities are rapidly becoming recognized in more and more industries. Production of garnet as an abrasive is confined chiefly to two areas in the United States, North Creek, N. Y., where the Barton Mines Corp. operates, and Emerald Creek, Benewah County, Idaho, where Occurrence: Garnets in the Emerald Creek area occur as disseminated crystals in beds of micaceous schists of the Belt Series, which in this section are estimated to be close to 4000 ft thick. The schists are high in alumina and silica with iron, manganese, and magnesium. Subjection of the original sediments to high temperatures and pressures caused metamorphism to take place with the resultant re-crystallization of high alumina-silica minerals such as garnet, mainly spessartite and almandite varieties, cyanite, sillimanite, chlorite, actinolite, tourmaline, biotite, and muscovite, with minor amounts of ilmenite and magnetite. Quartz is also present in considerable amounts. Fast erosion of the soft mica schists on exposure to weathering has created extensive alluvial deposits containing up to 10 pct garnet having a maximum grain size of 3/16 in. These alluvial sands and gravels are now being treated for the recovery of garnet sands. Treatment: Overburden of 1 to 4 ft must be stripped to expose the garnetiferous gravels. This operation and the subsequent feeding of the gravels to a trommel-screen washing plant are performed by a % yd dragline. The trommel-screen openings are 3/16 in., thus allowing a separation and concentration based on grain size, since over 95 pct of total free garnets are minus 3/16 in. All plus 3/16-in. material is wasted at this point. The minus 3/16-in. material is further concentrated in a sand-drag classifier, where the slimes and silts are washed out and wasted. The sand product from the classifier varies in garnet content from 20 to 60 pct according to the particular section of ground being worked. This sand product is trucked to a jig plant where two sized fractions are made in a trommel-screen. The minus 3/16-in. plus 10-mesh portion is fed to a Pan-American two cell 42-in. jig. The minus 10-mesh portion is treated in a Bendelari three cell 42-in. jig. The jig concentrates are combined to form a 98 pct garnet sand. The jig tailings contain 3 to 5 pct garnet which is mainly flat crystals and chips which will not settle into the jig hutch. Subsequent treatment of these tailings in a scavenger jig followed by drying and electromagnetic separation will, according to tests, reduce the garnet losses in the tailings to something around 1 pct. Jig treatment of this feed approaches ideal as the major portion of the garnet crystals are the natural dodecahedrons and so are, in general, close to spherical. The specific gravity of pure garnet is 4.2, while the next heaviest mineral in the feed is cyanite with a specific gravity of 3.6, then quartz with specific gravity of 2.6. The garnet concentrate is practically free of quartz. The predominant impurity is cyanite which amounts to about 1.5 pct. The rod-like crystals of cyanite appear to up-end in the jig and go into the hutch with the garnets. Some ilmenite and magnetite appear in the concentrate but in very minor amounts. Subsequent washing in a sand-drag classifier removes fine silts and iron oxides. The gravel feed to the washing plant will average 8 pct recoverable garnet content. Concentration ratio in this plant runs about 2.5 to 1. Washing-plant concentrate as fed to the jigs will average 45 pct garnet by weight. Concentration ratio of jigging runs about 2.2 to 1. The garnet concentrate is dried in a rotary oil-fired drier and then fed to vibrating screens in closed circuit with crushing rolls. Practically any grit from 10-mesh down to 150-mesh grain size may be graded to specifications in two 3-deck vibrating screens. The present production, however, is approximately 75 pct No. 36, 15 pct No. 60. and the balance No. 80 and No. 100. Metal-screen cloth is used for sizes down to 36 mesh. From 36 mesh and finer, silk-screen cloth is used since it has less tendency to blind. All garnet sand is bagged in 100 lb self-sealing, sleeve-type paper bags. Practically all shipments are made in carload lots. Car loading is convenient since the plant is in Fernwood on the tracks of a branch line of the Milwaukee railroad. Truck shipments can and are made occasionally.

Jan 1, 1951

By Thomas E. Wayland

AN isopachous map is one on which lines connect points of equal thickness of a given unit. This type of map is used by the Florida Phosphate Project of the U. S. Geological Survey to represent the economic phosphate deposits known as matrix and the waste material, or overburden, that overlies the matrix. The top of the bed on which the phosphate was deposited is known as the basement and a subsurface contour map of this old buried erosion surface is known as a basement map. Recent experiments have been made in preparing maps that show tonnages and grades of the phosphate content of the matrix. Few of the operating companies in the Florida phosphate district have applied isopachous (Greek isos, equal and pachys, thick) to mapping. The writer believes there is a need for the techniques discussed herein and that they can be applied to mapping other geologically similar areas in either economic or scientific investigations. The land-pebble phosphate district of Florida occupies a compact area in the west-central part of the state. It includes mainly the following land survey divisions: Ts. 27 S. through 32 S. and Rs. 20 E. through 26 E. The town of Mulberry, Fla., is in the approximate center of the district. The strata of the area, which is part of the Gulf Coastal Plain, occur in thin formations with broad outcrop belts, and low dips. The topography is subdued and gently rolling with three marine terraces, which are found at 30, 100, and 150 ft above sea level,' accounting for most of the relief. Occasional small sinkhole lakes are present, most of them above the 150-ft shoreline. The phosphate deposits occur in unconsolidated sediments such as clays, sands, and sandy clays. They are overlain by a heterogeneous assemblage of sands, clays, muck, and iron-cemented sand, easily penetrated, in most cases, by a hand auger or drill. Limestone, locally called bedrock, or a calcareous bedclay, thought to be a residue of the limestone, directly underlies the phosphate deposits. General Requirements Most companies and independent prospectors operating in the district have furnished prospecting data to the U. S. Geological Survey. The information is recorded on either field logs or prospecting maps and includes the following information for each hole drilled: location of the hole, thickness of the overburden, thickness of the matrix, phosphate content in long tons per acre, grade of the phosphate content expressed as the percentage of bone phosphate of lime (P2O5 x 2.18) or BPL, and the per- centages of iron-aluminum oxides and insolubles. The phosphate is classified according to size as either pebble or flotation material. The milling processes of the companies vary, and the size classification is necessarily different in many cases. However, pebble may be considered as larger than 14 mesh and flotation material as smaller than 14, but larger than 150 mesh. Some prospecting data include the exact depth at which bedrock or bedclay was reached, and these figures greatly increase the reliability of the data both for isopachous mapping and for mapping the basement. A drilling density of four holes per 40 acres of land furnishes a minimum amount of data for isopachous and related mapping. From the minimum of four, densities up to 32 holes per 40 acres are used. The various drilling densities may influence the choice of the proper scale. Selection of the proper scale is dependent upon the known drilling densities, the subsurface variations to be shown, the extent of the area to be mapped, and the detail desired in the completed map. Scales of 1:24,000, 1:4800, and 1:2400 are used in isopachous and related mapping by the Florida Phosphate Project. The 1:24,000 scale is used most effectively with drilling densities not exceeding eight holes per 40 acres. The subsurface variations should be relatively low and uniform, permitting the use of smaller intervals without undue crowding of the lines. Comparatively large areas can be mapped on this scale, but minute detail is necessarily sacrificed, because the information is drawn from a maximum drilling density of only eight holes per 40 acres. Isopachous and related maps of the 1:4800 scale are made of areas on which the drilling information covers from 4 to 16 holes per 40 acres. Moderate subsurface variations with relatively sharp gradations can be shown accurately. The area represented by the maps is reduced considerably in favor of detail. The 1:2400 scale is most frequently used by the Florida Phosphate Project. It lends itself particularly well to isopachous and related mapping, being easily adapted to the multiform drilling data available. Maps of this scale are prepared with information ranging from 4 to 32 holes per 40 acres; however, use of the minimum drilling density on the

Jan 1, 1952

By K. P. Gupta, A. K. Pal, L. Chandrasekaran, U. P. Singh

The Mn-Sn binary system, investigated at the high-manganese end and between 500° and 1000° C, shows four phases at temperatures below 727"C, namely the u Mn, the p Mn, the Mn3 Sn, and the Mn, Sn phases, while at higher temperatures only the last three phases remain stable. The solubility of tin in a Mn is very small and the maximum solubility of tin in P Mn phase appears to be abollt 10 at. pct Sn. The solubility range of the Mn,Sn and the Mn, Sn phases is 23.0 to 26.0 and 37.0 to 40.0 at. pct Sn, respectively. The lattice parameter of the 13 Mn phase increases with increasing tin content. The Mn, Sn thase is hexagonal with and appears to be basically of the Ni3 Sn type structure except that for quite a few X-ray diffraction lines the calculated and observed relative intensities do not agree well. The Mn-Sn binary system has been studied by several investigators.''~ Their results indicate that three intermediate phases, namely, the Mn3Sn, Mn,Sn, and MnSn, phases, exist at high concentrations of tin. However, so far the proper phase equilibrium has not been established at the manganese-rich end and very little data is available for the composition range between pure manganese and Mn3Sn. Moreover, earlier investigators differ in their opinion about the exact composition range at which the Mn3Sn and Mn,Sn phases appear and some doubt has been cast by some investigators3 regarding the structure of Mn3Sn phase which has been reported to be isotypic with Ni3Sn (Mgscd type) structure. In this investigation an attempt has been made to establish the proper phase equilibrium between pure manganese and Mn + 50 at. pct Sn composition in the temperature range of 500" to 1000°C. PROCEDURE The raw materials used were from three different sources. For exploratory work five alloys containing 5, 10, 15, 20, and 25 at. pct Sn were prepared using 99.9 pct pure manganese and tin supplied by E. Merck & Co., Germany. The rest of the alloys and one more 25 at. pct Sn alloy were prepared using 99.9 pct Mn supplied by Gallard Schlesinger Chemical Mfg. Corp., U.S.A., and 99.999 pct Sn supplied by Semi Elements Inc., U.S.A. Weighed amounts of manganese and tin were melted in recrystallized alumina crucibles in an inert gas (argon) high-frequency induction melting furnace. By careful control of temperature and time of melting the losses were reduced to below 0.2 pct in all cases. Since the losses were very small, no attempt was made here to analyze the samples chemically. Alloys were wrapped in molybdenum foil and sealed in small evacuated fused silica capsules. The alloys were annealed at different temperatures, controlled within + l°C, for sufficiently long periods to attain proper phase equilibrium, and subsequently quenched in cold tap water. The annealing periods used at different temperatures were 15 days at 500°C, 7 days at 600°C, 5 days at 700" and 750°C, 3 days at 800°, 850°, and 900°C, 2 days at 968"C, and two alloys annealed at 968°C were reannealed for 10 hr at 1000° C. From each annealed specimen, a part was utilized for metallographic study while another piece was used for X-ray diffraction study. 1.0 pct HNO, solution and oxalic acid solutions of concentrations 0.05 to 1.0 pct were used for etching Mn-Sn alloys above and below the MnsSn composition, respectively. Since all alloys were brittle, X-ray specimens were prepared using the as-crushed -325 mesh alloy powders. Only one 25 at. pct Sn alloy powder was reannealed in an evacuated silica capsule at 800°C for 5 min and water-quenched. X-ray diffraction patterns . for the Mn3Sn phase with the as-crushed and the reannealed powders did not show appreciable change. Un-filtered iron radiation at 25 kv, 15 ma was used with either Norelco 114.6-mm-diam Debye Scherrer Camera (for phase identification) or Norelco 12-cm-diam symmetrical focusing camera (for lattice parameter determination of the 6 Mn phase). The estimated accuracy of lattice parameter determination for the focusing camera was * 0.001A. RESULTS AND DISCUSSIONS The results of metallographic and X-ray diffraction study made with different alloys are shown in Fig. 1. The variations in lattice parameter with composition for the p Mn and the Mn3Sn phases are given in Tables I and 11, respectively, and the lattice parameter as a function of composition for the p Mn phase is shown in Fig. 2. The lattice parameter of the p Mn phase increases with increasing tin content while for the Mn,Sn phase the data obtained from two two-phase alloys and one single-phase alloy indicate increase in a,, and decrease in c, parameters with increasing tin content. The results, Fig. 1, indicate that the solubility of

Jan 1, 1969

By N. I. Fisher, J. Shepherd

A rapid method of determining natural fracture trends in collieries has been developed. The method will yield information that is precise enough to permit fracture domain boundaries to be delineated in a coal seam. Instead of a survey of cleat trends in a colliery taking several man-weeks or even man-months, a reconnaissance survey can be carried out in only a few man-days. At each of a sequence of sampling sites along a traverse, five measurements of trend are recorded for each set of fracture directions. A sequential plot of the medians of each fracture set is then made manually underground or by a computer in the mine office. Changes in fracture pattern can be detected easily in colliery development work if a geologist visits advancing faces regularly, and forecasts can be made about the likelihood of forthcoming faults and dykes. A full description of this method is given in Shepherd and Fisher (1981). The concept of mapping fractures rapidly in a colliery is based on using a geological traverse (Compton, 1962), along which observations can be made at chosen, regular intervals. The technique has been widely used for surface mapping across outcrops and in follow-up work in photogeological studies (Hepworth and Kennerley, 1970). In these cases, the geologist surveys the traverse line as mapping proceeds. In a colliery, however, ready-made traverse lines already exist in panels and along main roadways, often in several directions. It is thus possible to traverse a colliery in different directions and record the fracture trends at intervals, generating a reconnaissance fracture map. This can also be done on a continuing basis as mine development takes place. Generally, a sampling traverse should be longer than 0.5 km with sampling sites at relatively close-spaced intervals along the traverse. For example, in room-and-pillar mines pillars are commonly formed on 40-m centers and the sampling sites can then be arranged at 20-m intervals [(Fig. 1)]. The sites might have to be closer together for mines known to have bad mining conditions. The predominant fracture trend is normally the face cleat and the subordinate trend is the butt cleat (McCulloch et al.. 1974). Various changes can occur in the cleat or joint pattern: the face and butt sets may disappear or an entirely new set or sets may appear. Therefore, it is best to record all prominent fracture sets. Sometimes there is only one; in other cases there may be as many as three or more. An odd number of measurements of each fracture set are made (generally five or more) to enable the median value to be determined easily. The median value can be plotted underground using graph paper or a computer plot can be made in the laboratory or mine office [(Fig. 2)]. The sequential linked median (SLIME) plot draws the median trend for each sampling site as a unit line segment. The segments from successive sampling sites can be connected together to form a long chain [(Fig. 2A)]. The needle plot, on the other hand, draws a straight line to represent the traverse and then plots out the median trend for each sampling site [(Fig. 2B)]. The SLIME plot is better for visual display, as it highlights small irregularities and gross changes in trend. However, some work is required to relate the individual segments to their site location along a traverse. In this respect, the needle plot is more convenient because each segment -can be plotted-at a point corresponding to its location. Also, there is precise match-up if needle plots of face and butt cleat are compared. A description and listing of the SLIME program is given by White et al. (1981). An example of the use of this method is given for Wallsend Borehole colliery in New South Wales (Australia) [(Fig. 2)], where domains II and IV are associated with mining hazards. Domain II is coincident with a normal fault of 2.6-m throw, and domain IV with a basic dyke 12 m thick. These hazards were approached driving in a southwesterly direction, and a pronounced change in trend of the cleat to a northwesterly direction occurred at a distance of approximately 45 m from each one. The northwestern joint trend is parallel to that of the dyke and fault, and it occurs at a higher frequency close to these structures. The association of a particular joint set with faults has been found elsewhere (Shepherd and Creasey, 1979). The two minor cleat direction changes within domain V are narrow joint zones that are less than 5 m wide. The fracture trends derived from a SLIME traverse can be verified by collecting larger quantities of data at selected sites, as shown in the balloon density (rose) plots depicted in [Fig. 2C]. We are grateful for the financial support provided by Thiess Bros. Pty. Ltd. and the National Energy Research, Development, and Demonstration Program administered by the Commonwealth Department of National Development and Energy. R.W. Miller Holdings Ltd. and Thiess Bros. Pty. Ltd. are thanked for their permission to publish data from their collieries.

Jan 1, 1982

Jan 1, 1900

Jan 1, 1933

By C. B. Foster, S. I. Freedman, E. M. Jamgochian

Coal-oil mixture (COM) combustion technology is regarded by the US Department of Energy (DOE) as near term and Potentially applicable to existing utility and industrial steam generators and for injection into blast furnaces. From work done previously, it has been established that COM can be burned in existing boilers and blast furnaces. Therefore, the issues being addressed by the current DOE program are: (1) determination of best available technology to achieve environmentally acceptable long-term reliable operation and (2) determination of applications for which COM can be utilized economically. Some of the technological options have begun to be determined by projects already under way. However, many projects are still in the early stages of development.

Jan 1, 1980

By Charles A. Chase

This paper, descriptive of a single mine, is presented in the belief that it may furnish useful suggestions to mine-managers encountering similar problems; and it includes the details which will enable them to estimate the value of the methods employed—especially where these depart from common practice. Tt should be added, however, that this mine is not typical of the San Juan district, but differs markedly from neighboring mines in physical conditions and metallurgical requirements. The Liberty Bell mine is situated in San Miguel county, Colo., on the west front of the San Juan mountains, 2 miles north of Telluride. The vein was discovered in 1876 by Wm. L. Cornett, who, with subsequeilt locators, took up claims along the apex. A few hundred feet of development-work was accomplished, and a few? tons of ore were smelted or milled; but profitable working proved impossible under existing

Jan 1, 1912

By Otto Henry

THE purpose of this investigation was to determine the equilibrium diagram of the lithium-magnesium pair as a first step in studying the possible usefulness of these alloys as ultra-light structural materials. REVIEW OF THE LITERATURE The behavior of lithium towards magnesium was first investigated by Masing and Tammann.(I)? In order to prevent oxidation the alloys were made in iron tubes under an atmosphere of hydrogen; temperatures were measured with a glass-protected thermocouple. These investigators found that lithium and magnesium form two series of solid solutions separated by a miscibility gap between 85 and 95 per cent magnesium; that the alloys with 81 and 95 per cent magnesium showed a homogeneous structure under microscopic examination, while the alloy with 89 per cent magnesium contained two distinguishable crystallites; that the curve indicating the beginning of crystallization rises from the melting point of lithium to that of magnesium; and that no compounds of lithium and magnesium are formed. The equilibrium diagram was not plotted because no definite data were obtained for determining the solidus and the posi-tion of the miscibility gap in the solid state. The difficulties encountered in this investigation were: (1) that it was necessary to heat them as high as the melting point of magnesium in order to obtain homogeneous melts; at such temperatures the alloys attacked the glass protecting the thermo-couple; and (2) that at temperatures above 400° C. the lithium united

Jan 1, 1934

By S. Chander, D. W. Fuerstenau

The inherently sluggish nature of the reactions involving sulfide minerals, particularly molybdenite, in aqueous solutions under ambient flotation conditions make their investigation complicated and difficult. Since the physicochemical nature of sulfides is known to be controlled by electrochemical reactions, a number of attempts have been made in the past to study sulfide mineral-collector interactions through rest potential and electrode polarization measurements. The purpose of the present investigation was to study the interaction of potassium diethyldithiophosphate (KDTP) with molybdenite. In the present investigation of the interaction of KDTP at the molydenite surface, molybdenite electrode rest potential measurements and electrode polarization behavior were experimentally determined under various solution conditions. The standard reduction potential for the equilibrium between dithiophosphate ions (DTP-) and bis(diethoxythiophosphoryl)disulfide (DTP) [(DTP). + 2e :i7-± 2DTP- (1)] can be evaluated from the electrode rest potential measurements on a platinum electrode in deoxygenated KDTP solutions saturated with freshly prepared (DTP)2. Experimental A platinum wire was used as the electrode for potential measurements. Prior to each measurement the elec-

Jan 1, 1975

By Ernest F. Burchard

PAGE. I. Introduction,........... 75 II. Outline of the Geology......... 76 1. Stratigraphy............ 76 A. Clinton Formation........ 77 2. Structure...........82 3. The Ore..........85 A. Character............ 85 B. Geographic Distribution....88 III. Local Descriptions........... 88 1. Birmingham District.......... 88 A. Topography and Its Relation to Industrial Development... 88 H. Distribution and Structure of Formations.... 89 C. Divisions of the Birmingham District. 95 Division A (Description of the Ore-Beds), . 95 Division B.........105 Division C.......... 106 Division D,..107 Division E,...........108 Division F........ 111 Division C.......... 112 D. Mining .Development.... 113 2. Northeast Alabama........114 IV. Possible Origin oF the Ore......... 119 V. Relation of Origin to Quality and Extent of Ore... 122 VI. Estimates of Ore-Reserves,......... 125 1. Method of Making Estimates......... 125 2. Data and Results....126 VII. Production and Consumption oF IRon-ORe,.... 132 I. Introduction. Brief and interrupted studies of the Alabama Clinton iron-ores have been made within the last four years by members of the IT. S. Geological Survey. Reports on the progress of this

Jan 1, 1910

By Alexander R. Troiano, Eugene P. Klier

Since the very early work on quenched structures, where the products of the martensite transformation had been recognizedl this transformation has provoked much interest and study. Theoretically it was desirable to account for the extreme changes in physical properties resulting from the formation of martensite, as that information might lead to results of practical importance. Desirable information, therefore, was on the kinetics of transformation from austenite to martensite as well as on the physical constitution of the martensite. It has been known for years that certain steels quenched to room temperature will contain persistent austenite as well as martensite. Other important and now well-established features of the martensite reaction are the Progress of the reaction on cooling only and the independence of Ar" with cooling velocities exceeding the critical velocity. These facts have been experimentally determined by various methods and investigators. Notable among the early investigators were Tammann and Scheill and Wever and Engel.2 Unfor- tunately, all investigators did not fully interpret their results, which, coupled with several investigations that yielde. conflicting resultsl caused a state of confusion that was not clarified until quite recently. X-ray investigations of martensite in steels3-6 indicate it to be a supersaturated solid solution of carbon in alpha iron. This supersaturation is evident from the appearance of a body-centered tetragonal structure with the addition of sufficient carbon. The dimensions of this tetragonal structure are a linear function of the carbon content within the limits of accuracy of the determinations. Slight tempering of tetragonal martensite leads to the destructi,, of the tetragonal structure, which is converted to a body-centered cubic strutture. This phenomenon has precipitated a controversy concerning the nature and mechanism of the tempering of martensite The facts in the case have been outlined by Epstein7 and more recently by Antia, Fletcher, and Cohen.8 The significance of Ar" on theoretical grounds is not clear, however, although considerable study has been devoted to its determination. The precise position of Art' aS a function of carbon content was first stated by Greninger and Troiano9 for steels covering a range of approximately 0.7 to 1.8 per cent carbon. The effect of alloying elements on Ar" has recently been the subject matter of investigation by various methods.

Jan 1, 1945