Search Documents

By Arthur L. Bishop

INTRODUCTION Purpose The in-situ leach method for uranium extraction is a relatively new and innovative method of uranium mining. In 1975, the first commercial in-situ facility began operation in south Texas. Since that time numerous other operations have been initiated as either pilot or commercial ventures. Considerable literature has been published that deals primarily with generalities of the process or environmental concerns. Several federal agencies have published documents which do not reflect the true operating or environmental nature of the in-situ leach method of uranium extraction. From an environmental standpoint, this is also evident in the promulgation of rules and regulations. Hence, the purpose of this paper is to present experience with an environmental concern--non- production zone excursions--such that the industry and the regulatory agencies will gain greater insight devoid of preconceived ideas and misconceptions. General Process Description In south Texas, in-situ leach mining is utilized to extract uranium from permeable sandstone ore deposits 61 to 213 meters (200 to 700 feet) below the surface. Uranium is present as an insoluble uranium oxide. In the in-situ or solution mining technique, anoxidizing lixiviant is injected into the formation through injection wells. The solution reacts with the insol uble carbonate complex. This soluble uranium complex is produced at recovery wells, each containing a submersible pump. During production there is a constant sweeping of lixiviant through the formation from the injection wells to the recovery wells. Injection and recovery wells can be arranged in any of a number of geometric patterns dependent upon ore body configuration, aquifer permeability, and operator preference. Submersible pumps in the recovery wells pump the uranium rich pregnant solution to the initial processing facility. Monitor wells surrcsund the pattern area and are screened in appropriate stratigraphic horizons (production and non-production zones) to detect any lixiviant migration that may occur (Fig. 1).

Jan 1, 1980

By W. H. Adams

Among the engineering plants with new features and deserving details which are constantly being brought to the working stage in the Southern States by the generous expenditure of capital, none can exceed in interest, whether to the public or the profession, the incline-railway built from base to summit of Lookout Mountain, near Chattanooga, Tennessee. Much geological and historical interest centers in this section of the middle mountain-country. Of its geology, the Transactions of the Institute contain many particulars. Of its history, the most

Jan 1, 1888

By J. S. Seawright

Haulage is a costly feature in the operation of an open pit mine, whether it be iron, copper, or limestone. The National Iron Co. has adapted an old underground method to the open pit inclined skip haulage to bring the ore from the pit bottom to the crusher or beneficiation plant. The Rockover skip has been placed in operation where limited areas have retarded or eliminated use of long rail or road slopes. Deep and narrow orebodies subject to rapid increase in depth that discourage use of conveyor belts and necessary crushing plants are ideal for this system. The skip haulage method was developed to combine the desirable features of conveyor, truck, and rail haulage and at the same time avoid the draw- backs. The skip was designed to follow the natural angle of repose of the pit wall and can vary from 25° to 45°. Open-pit skips now in operation show that the installation is successful and provide the

Jun 1, 1955

By C. W. Mac Gregor

THE observation of the flow layers, or Lüders' lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-steel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are in reality traces of wedge-shaped flow layers and are formed by the inter-section of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45° to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ner, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45° to the principal stress direc-tions at the point. As examples of the latter may be mentioned the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subjected to internal pressure only, etc. Hence if the flow layers are observed from an experiment, the shear-stress trajectories -the curves indicating the directions of the maximum shearing stresses in the body-may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45° to the principal stress directions, the family of principal stress trajectories, or the curves indicating the directions of the principal stresses, may be thus obtained. Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowan;1 in duralumin and other aluminum alloys, by Dawidenkow, 2 Elm,3 Fell, and others; in copper and copper-alloy crystals, by Elam;5 in brass by Elam;5 in brass wires by deForest;6 in higher carbon steels, tungsten steel, and

Jan 1, 1939

By A. C. JR. Boyle

I. INTRODUCTION THE geological field work of the Bully Hill district, upon which this paper is based, was begun July 1, 1908, and covered a period of three months. The time was found too short for a complete report and the district was again visited in the early part of July, 1912,. from which time detailed study of the locality continued until September of the same year. This paper is the result of observations made in the mines in the immediate vicinity of Winthrop, Shasta county, Cal., during these two periods of study. The preparation of this report has been greatly facilitated by various courtesies rendered the writer by D. M. Riordan, President of the Bully Hill Copper Mining & Smelting Co., and by John B. Keating and Herbert R. Hanley, managing officers actively in charge at the mines. The elaboration and further study of the notes and collections were carried on in the laboratories of the Departments of Geology and Mining at Columbia University, and the writer takes pleasure also at this point in expressing his acknowledgments to Profs. James F. Kemp, A. W. Grabau, Charles P. Berkey, and William Campbell, for advice and assistance. In order that one may appreciate at first reading the significance of some of the details which follow, and for the sake of clearness, a brief outline of the geological relationships is here given, together with certain conclusions which have been reached regarding the genesis. of the ores and the gypsum masses. In the Bully Hill mining district an associated series of Triassic lavas and tuffs, chiefly andesites, is preceded as well as followed by sediments. The entire system is tilted so that the original bedding planes dip in general to the southeast. The surrounding region has been greatly disturbed, and in the immediate vicinity of the mines close folding of the later sediments and extreme shearing of the igneous rocks locally is a striking feature. Into the nearly vertical shear zones have been intruded post-Triassic dikes of various rock types in the following order: alaskite-porphyry and andesite-porphyry. Outside the area under consideration diorite dikes are known, but they will not receive attention further than to note that' they, probably, represent a differentiation product of the same magma from which the other two dikes came. In this connection all the dikes have an important bearing on the origin of the ores and of the gypsum found in the mines.

Jan 1, 1914

By A. U. Seybolt, J. L. Walter

The effects of the addition of 0.5 pct ThO2 (by volume) on the grain structure and texture of heavily rolled tungsten sheet were studied. Powder metallurgy ingots were rolled to sheet, 0.001 in. thick, and samples were annealed at temperatures from 1200" to 2500°C. The heating rate to the anneal temperature was varied from 3°C per min to 6500°C per min. The orientations of the largest grains were determined by X-ray diffraction. The disposition and loss of the ThO2 particles were determined by electron transmission microscopy and the activation energy for remozlal of the thorium was measured by mass spec-troscopy. Heating rates below about 800 C per min produced large, highly elongated grains. Higher heating rates produced much smaller, less elongated grains. The grain structure and texture of the slowly heated samples were identical to the structures and textures of heavily rolled tungsten foil conventionally doped with aluminum, silicon, and potassium but the recrystallization temperature was about 200°C lower. There was stringer-like dispersion of larger ThO2, particles superimposed on a uniform dispersion of fine particles. The particles increased in size and decreased in number with time at temperature. The loss of particles was accompanied by formation of grain boundary voids and surface pits. The activation energy for removal of the ThO2 was about 40 kcal per mole. THE addition of small amounts of aluminum, silicon, and potassium to tungsten has a profound effect on the grain structure of heavily rolled sheet1 or drawn wire."4 Thus, "doped" tungsten sheet, rolled to 0.001 in. and recrystallized, develops a structure consisting of large, highly elongated grains of a specific preferred orientation.' It has been shown that the elongated grain structure was caused by a dispersion of particles, identified as mullite (Al6si2O13),1,4 in strings parallel to the rolling direction in sheet or to the wire axis. Identical results were obtained for iron which was doped with glass and rolled to 99 pct reduction of thickness and recrystallized.5 Again, the glass particles were disposed in strings parallel to the rolling direction. The strings retarded boundary migration in the lateral direction but grain growth was able to proceed relatively unhindered along the direction parallel to the strings.1,5 In both the doped tungsten and the glass-doped iron, the particles were highly plastic during the high-temperature deformation. Since mullite melts at about 1800°C and the glass employed melts at about 810ºC, the particles were probably molten during the recrystallization anneals (above 1800°C for the doped tungsten and 850°C for the glass-doped iron). There are indications in the literature that particles not plastic at hot-working temperatures (up to about 1550°C for tungsten) may also impart elongated grain structures by primary recrystallization of worked alloys. Examples are dispersions of tantalum carbide in chromium,6 and ThO2 in nickel where elongation ratios of recrystallization grains of up to 20:l were obtained.7 Strings of ThO2 particles in W-ThO2 wire have been seen by Rieck.8 In view of the available evidence, it was of interest to extend the previous studies of doped tungsten and glass-doped iron to include W-ThO2 sheet materials. Of specific interest was the grain structure, preferred orientation, recrystallization temperature, and disposition of the thoria particles. EXPERIMENTAL PROCEDURE A) Material Preparation. About 380 g of blue tungsten oxide (approximate composition WO3) was wet with a sufficient amount of aqueous solution of Th(N03)4 to provide 0.5 vol pct ThO2. The wet mixture was stirred to distribute the doping material uniformly throughout the powder. Stirring was continued while the mixture was heated until it was completely dry. The dried, doped mixture was then reduced to tungsten powder by heating at 850°C for 2 hr in a stream of dry hydrogen. The doped tungsten powder was hydropressed in a rubber sack at pressures of 50,000 psi to produce an ingot approximately 2 cm diam by about 5 cm long. Next, the pressed cylinder was heated in hydrogen for 2 hr at 1350°C to render it strong enough for machining. The cylinder was machined to a square cross section of 1.6 by 1.6 cm with rounded corners. Finally, the bar was heated for 2 hr at 2150°C in hydrogen to provide a sufficiently dense mate rial to withstand the hot-rolling operation. Prior to rolling, the ingot was reduced in thickness by about 20 pct by forging at 1550°C. This served to increase the density of the material and to widen it slightly for better rolling characteristics. The forged ingot was then rolled at 1550°C to a reduction of 45 pct of thickness, following which the rolling temperature was reduced to 1300°C and the slab rolled, with several reheats, to 0.050 in. Further reduction was accomplished at 800°C in tungsten sheet packs to a total reduction of about 99.85 pct. B) Annealing Treatment and Observation of Structure. Small samples of the rolled foil were annealed in one of two ways. Some of the samples were suspended in a covered tungsten can and annealed at temperatures from 1200" to 2200°C for various times in vacuum of l0-7 to 10-6 mm Hg. The can was heated by induction and temperatures were determined by optical pyrometry

Jan 1, 1970

By A. W. Furbank

IN reviewing the aerial cameras produced in different countries, it becomes apparent that in nearly all of them an attempt has been made to secure the greatest possible angle of view. This angle, of course, is determined by the objective. The objectives most commonly in use in aerial cameras have a maximum angle of 65°. The objective developed for this new Zeiss camera combines freedom from distortion and brilliant definition, with an angle of 95°. Aerial mapping, it is claimed, has been placed on a different economic basis, and new possibilities presented, par-ticularly in connection with automatic stereoscopic plotting instruments, to which some short references are made. One way of enlarging the angle of view is to couple several instruments with their axes convergent, thereby producing a multilens camera. Typi-cal of cameras of this sort in the United States is the Bagley four-lens camera, which later was developed into the five-lens camera (T3-A) of the U. S. Air Corps. More recently, in order to get away from the unfavorable Maltese cross image field of the five-lens camera, and to obtain a more practical form, two five-lens cameras were combined. By using them in tandem and rotating them by 45° relatively to each other, a ten-lens camera was produced, covering an octagonal ground area, with a total angle of view of 140°. Similar designs have been evolved in other countries. In all of them, however, a number of difficulties have arisen, quite apart from their large weight and high cost. Because of their complex mechanism, numerous shutters and magazines, and the high precision with which these parts must be interadjusted and synchronized, these cameras are far from dependable. Moreover, a multilens camera by itself does not yet constitute a complete outfit for producing pictures suitable for photogrammetric survey. Because all the component pictures, except the central one, are obliques, it is always necessary to employ rectifying apparatus which transforms the marginal views to the perspective of the central one. In multilens cameras with many individual magazines, it is not convenient to

Jan 1, 1938

By F. Lynwood Garrison

There is probably no subject for study in the metallurgy of iron and steel of greater interest than the effect of manganese upon the properties of iron. Some of the peculiarities of iron and steel containing appreciable quantities of manganese were observed many years ago by Heath, Robert Mushet, and others; but it was not until the introduction of the Bessemer process, when a demand was created for large quantities of iron-manganese alloys, that such compounds of iron and manganese became articles of commerce. Since that time the demand for these alloys has steadily increased, the use of ferro-manganese not only becoming an absolute necessity in the ordinary Bessemer practice, but also essential to the manufacture of open-hearth, crucible steel and steel castings; in fact it is the only source of supply for all the manganese used in metallurgical opera-

Jan 1, 1893

By O. I. Deschon, Ralph Arnold

Deep drilling was the keynote of the more important developments in the North Rocky Mountain region during 1929, with Montana recording the most important achievement through discovery of three new oil fields. Alberta produced 1,000,000 bbl. of 74 gravity naphtha, showing a considerable gain over 1928, developed a commercial oil pool in Turner Valley and extended that field 8 miles southward. Wyoming's discovery field was deepened to a second producing horizon, giving impetus to deeper drilling, and practically every Wyoming oil field will have a deep test either this year or in the near future. Whereas Montana prospecting has been confined to the shallow plains structures, since the discovery of Kevin-Sunburst field, the coming year will see an active search for new oil and gas pools in sharp-dip structures, following the success of prospecting in the Sweetgrass Hills during 1929. A dozen or more structures have been mapped in North Central Montana, several of these straddling the Alberta border. Four structures tested thus far have all shown commercial oil or gas or both. Sweetgrass Hills The first important development in the Hills area was the Rogers-Imperial gasser, which had an initial of 51,000,000 cu. ft. of dry gas per day, with a rock pressure of 1080 lb. This well is located on a sharp nose running north from the hills into Alberta. Several wells drilled by independent operators on the American side, on the west flank of reserve structure, have developed a total open flow capacity of 30,000,000 cubic feet. The third structure tested in the Hills area is known as Bears Den, where commercial oil was found at the base of the Cretaceous at 2470 ft. The existence of oil in three lower sands has been established by two wells on the top of the structure, these two wells finding gas flows of 10,000,000 and 15,000,000 cu. ft., respectively, in the horizon where

Jan 1, 1930

"In the spring of 1927, six members of the American Institute of Mining and Metallurgical Engineers met for dinner at the Chemists' Club in New York to discuss the possibility of setting up a committee within the Institute to further the current interest in the science of steelmaking. Attention' to this subject had been crystallized by a symposium held by the Faraday Society in 1925. ' After a prolonged discussion, ranging from thermodynamics to slag conditioning, it was decided to approach the Institute with the request that a standing committee on "The Physical Chemistry of Steel Making" be set up. This committee proposed to promote scientific and practical papers on the subject, and was designed to cooperate with the Open Hearth Committee of the Institute in bringing scientific developments to the attention of open-hearth operators throughout the country... . "As the life of the [Physical Chemistry of Steelmaking] Committee lengthened and general interest in the technical phases of steelmaking grew, it became evident that there was a distinct need for a book that might serve the open-hearth interests to better advantage than standard texts whose scope is necessarily wide and whose detailed exposition of the open-hearth process is, therefore, somewhat limited. With this thought in mind, the Committee, after some years of consideration and debate, embarked on the venture of writing a manuscript on `Basic Open Hearth Steelmaking'." The foregoing paragraphs, taken from the introduction by C. H. Herty, Jr. to the first edition, well describe the circumstances which led to the publication of "Basic Open Hearth Steelmaking" in the spring of 1944. The book consisted of nineteen chapters contributed by twenty-three authors and edited by the staff of Alloys of Iron Research and T. S. Washburn, B. M. Larsen, and J. S. Marsh with Frank T. Sisco as consulting editor. The Engineering Foundation and the Open Hearth Steel Committee of the Iron and Steel Division, AIME, made financial grants; steel companies and other organizations supported the publication by contributing time and expenses of staff members in their capacity as authors or editors. The volume was sponsored by the Seeley W. Mudd Memorial Fund and appeared under the

Jan 1, 1951

By B. Fitch

This paper deals with the behavior of sedimenting suspensions. More particularly, it treats, in as organized a manner as possible, the body of knowledge, theoretical or empirical, by which one predicts the behavior of miscellaneous swarms of particles in suspension. Such knowledge is necessary for precise and economical design of equipment. While the behavior of a single spherical particle settling through an infinite sea of quiescent fluid is well understood, practical sedimentation processes are almost always concerned with particles of assorted sizes, densities, and shapes, in such concentration that there is profound particle interaction. Such swarms of particles are observed to settle in any of four markedly different manners. Which one they follow is governed by particle interaction. It is determined largely by the dilution of the suspension, and the relative tendency of the particles to cohere. TYPES OF SEDIMENTATION The relationship between the different modes of sedimentation is shown paragenetically in Fig. 1. The left side of the diagram represents particles having little tendency to cohere; the right side represents particles for which interparticle cohesion is large compared to the settling force. The vertical axis represents dilution. As seen in the diagram, sedimentation is divided into three broad fields or regimes. At high dilutions there exists a regime here named 'clarification.' Particles in clarification may settle either individually, or by collecting into separated floccules. Thus there are two different possible modes of settling in the clarification regime. It is characteristic c~f this regime that there will be no clear line of demarcation between settling suspension and a supernatant. Faster particles settle out ahead of slower ones. In batch tests there develops a gradation of both particle sizes and pulp density due to progressive depletion of the largest particles from any given pulp level.

Jan 1, 1962

By Dennis A. Clark, Brent Larsson

Tunnelling today is a lot more than drilling and blasting. The developments in drilling and blasting technique have made it pos¬sible to save costs both by increasing the advance per round and optimizing the demands on the final contour. Increasing the hole depth by using longer feeds and bigger dril¬ling rigs make the drilling time shorter compared to the set up time. It is important that the deeper holes are followed up by using a suitable cut. The most common cut in Sweden today is a parallel hole cut with one or more large holes; with a diameter corresponding to the hole depth and wanted advance per round. It is often specified that smooth blasting is to be carried out with a specific drill hole spacing. It is extremely rare, however, for specifications to be issued concerning the alignment of the raw of holes closest to the contour holes. It is very easy to ruin the effect of smooth blasting altogether by firing the rest of the round carelessly with an excessively high charge distribution. The drilling and blasting of the contour holes and the line of holes closest to the contour holes is therefore an extremely important part of any underground work. Accuracy and care in connection with the drilling of contour holes is also extremely important since it is possible to reduce the amount of overbreak, the result being more rapid mucking out, smoother and more durable surfaces and also less consumption of concrete for lining purposes.

Jan 1, 1983

By G. J. Saulnier, K. E. Goddard

The US Geological Survey has developed mathematical modeling techniques to assess potential impacts on the hydrologic system resulting from mining of coal and oil shale in northwestern Colorado. Potential impacts of oil shale mining on groundwater hydrology have been simulated using a quasi-three-dimensional, finite-difference model. The model has been used to simulate hypothetical mine dewatering operations at two proposed oil shale mines. Dissolved-solids distribution and solute transport were simulated with a three-dimensional, finite-difference model that was used to evaluate the effects of flooding in hypothetical abandoned mines. The potential impacts of coal and oil shale mining on water-sheds were investigated using a digital watershed model. This deterministic physical-process model predicts responses of the hydrologic system to modifications resulting from mining in basins having snow as the major source of runoff and recharge. Potential impacts of coal development on surface water quality were investigated using a river quality assessment model. The models developed by the US Geological Survey have been useful in defining the potential effects of mining in northwestern Colorado. They are an important first step in analyzing the existing data base and in predicting impacts and new data needs. The models may not be totally applicable on the local scale but are very meaningful on the regional level.

Jan 1, 1983

By J. A. Snyder, W. L. Finlay

SEVERAL notable studies of the effects of sub- stitutional solutes have been reported. Outstanding among these for its elucidation of general principles, is the summarized work of Hume-Rothery and coworkers.1 For a systematic study of the effects of substitutional solutes on the mechanical properties of the solvent lattice, the work of Brick, Martin, and Angier² on copper; of Frye and coworkers³,4,5 on copper and silver; and of Lacy and Gensamer6 and of Austin7 on iron may be mentioned. Titanium is one of the few elements offering the possibility of a similar study of interstitial solutes since, unlike most metallic elements, it exhibits extended solid solubility for most of the interstitial solutes—hydrogen, boron, nitrogen, oxygen, and carbon. This paper reports a survey of the effects of dilute solutions of nitrogen, oxygen, and carbon on the mechanical properties of high-purity alpha titanium. Previous Work: Van Arkel and De Boer showed" that high purity titanium was quite ductile and De Boer, Burgers and Fast established".' that not only were oxygen and nitrogen very soluble in solid titanium but that, long before the limit of solid solubility of either had been reached, these interstitial solutes rendered the metal brittle. Their electrical resistance data as a function of

Jan 1, 1951

By Reginald Williams

THE amount or value of the precious metals consumed in dentistry is probably amazing to most people. It falls very little short of that which is consumed in jewelry. Inasmuch as the ultimate destination is in the human mouth, dental alloys enjoy some importance because life and health depend upon restorations made with them. Prosthetic dentistry has made wonderful progress in the last few years. The manufacturers who supply the metals also deserve commendation. This industry which deals with metals to go into people's mouths is comparatively new. There is no literature on the subject, and little or no precedent by which to be guided. It was only by close cooperation with the dentist or prosthetic technician that desirable physical properties were produced, as nearly as possible, in the metals which were available and permissible. It is true that there were and still are conflicting opinions among the dentists as to the physical properties they require. Sometimes they request the impossible, such as alloys which are exceedingly stiff and springy, yet will bend or adjust easily. Even in this latter instance, progress has been made by supplying methods of heat-treatment whereby metals may be softened or hardened at will. (Figs. 1 and 2.) The demands made upon manufacturers are extremely varied. They must supply metals of tensile strengths ranging from approximately 30,000 to 100,000 lb. per sq. in. and over. The latter metals must be workable and in many instances capable of extreme deformation. They must not be affected by mouth conditions, nor should they oxidize greatly when molten, at red heat, or during a soldering operation. In addition to physical specifications, color demands must also be met. The firm of which I have the most knowledge manufacturers 11,553 standard stock articles of precious metals, taking into consideration formulas, finenesses, grades, colors, gages, lengths, sizes and weights. If special demands are taken into consideration, the number would be in excess of 25,000. Wrought metals are manufactured in a great many alloys of different sizes and shapes, such as plate, bar, rod, wire, sheet, strip, mesh and foil. There are also other products of importance.

Jan 1, 1928

Jan 1, 1924

By Waldemar Lingren

CONTENTS. PART I.-GENERAL FEATURES. [ ]

Jan 1, 1902

By Henry Ferguson

THIS paper is a preliminary statement, intended to present the more important results of the recent studies of the ore deposits of the Alleghany district in advance of the publication of the complete report, now in preparation. The Alleghany district (Fig. 1) has been a producer of gold since the early days of California gold mining. As in other California gold camps, placers yielded the bulk of the earlier production, but during the last 30 years lode deposits have been the only important source of output. The district differs from other California gold-quartz districts in that nearly all the production is from small shoots of high-grade ore. The mining camps of Alleghany and Forest are on the western flank of the Sierra Nevada range about 20 miles west of the crest. The gently sloping lava-covered plateau which controls the upland topography has been trenched by deep canyons of the westward flowing streams, which are cut to depths of as much as 2000 ft. below the crests of the ridges. The district is about 18 miles from Nevada City but the automobile road which connects the two places is 31 miles long. The senior writer first visited the district in 1913 and published a short description of the lode deposits.1 The increasing importance of the district made further study desirable. A detailed topographic map was therefore made by W. B. Upton, Jr., of the U. S. Geological Survey, in the spring of 1924, and the senior writer spent parts of the field seasons of 1924 and 1925 in the district. For the second field season the Geological Survey was fortunate in securing the services of R. W. Gannett, who had already done geologic work in the district for several of the mining companies. Owing to the death of Mr. Gannett in October, 1925, just before the close of his field work, the work of preparation of the entire report fell to Mr. Ferguson. He takes this opportunity of acknowledging how deeply he is indebted to Mr. Gannett for his excellent work in the field, and his realization of how greatly the completion of the report on the district has suffered from lack of Mr. Gannett's assistance in the office. In October, 1.928, after the completion of the first draft of the manuscript, Mr. Ferguson made a short visit to the district.

Jan 1, 1929

By W. Philippoff

ALTHOUGH Gaudin1 and more recently Sutherland2 have calculated the probability of collision of a falling mineral particle with a rising bubble, there is no published information concerning the details of the mechanism of attachment of a collector-coated particle to a bubble. During the past year the writer has developed a theory for the mechanism of attachment, which has been substantiated experimentally. Funds for the investigation and for some of the equipment used have been supplied by the Mines Experiment Station of the University of Minnesota. Motion picture studies of the phenomena involved in the collision between mineral particles and bubbles, such as those of Spedden and Hannan," show that the contact can be completed within 0.3 millisec. Formulas developed for rigid bodies have hitherto been used' for the calculation of the motion of bubble and particle, but it is obvious that a bubble cannot be regarded as a rigid body. On the contrary, Spedden and Hannan's pictures show a great degree of deformation during the collision. The time of attachment was calculated as the time the particle drifted past the bubble. Time of Collision The theory presented in this paper enables calculation of the time of collision, using the concept that the bubble, or more generally, a liquid-air interface, acts as an elastic body. The elasticity, defined as the restoring force on a mechanical deformation, is caused by the surface tension and is the result of the principle of the minimum of free surface energy. It is well known that an elasticity together with a mass determines a frequency of vibration. The vibrations of jets and drops caused by the elasticity of the interface are known to comply exactly with the classical theory of capillarity.' However, the vibrations of isolated bubbles, as distinct from foams, have not been investigated previously. The following equation, presented elsewhere,' has been deduced for these frequencies: 3_____________________ fB = 9.20.vV.vn. (n-1).(n+2)/8 [I] in which fB is the frequency of a harmonic of the bubble in cycles per second, V the volume of the bubble in cc, n a number determining the order of the harmonic, and n = 2 the basic vibration. The first (basic) harmonic describes a change of the spherical bubble to an ellipsoidal bubble. The higher harmonics are more complicated, for the circumference of the bubble is divided approximately into as many parts as the order of the harmonic. As an example, Spedden and Hannan's published motion picture of a vibrating bubble corresponds to the sixth harmonic. Eq 1 shows that only the first and third harmonics are simple multiples (1 and 3), all the others being irrational fractions of the basic frequency. This means that the shape of the vibration can change with time and is in general unsym-metric in respect to the time axis. Such conditions prevail when there is a distributed elasticity or mass, as in the case of vibrating membranes or rods. The constant 9.20 is valid for water at room temperature, but a general solution involving the physical constants of the liquid has not been found. The case of the floating particle is much easier to treat than that of the bubble. It can be assumed that the elasticity is caused exclusively by the interface and that the mass is concentrated in the particle together with some adhering water. The following expression for the frequency of a system of one degree of freedom can be applied: fP = -1/2-vE/m [2] Here fp is the frequency of the particle vibration in cycles per second, E the elasticity in dynes per cm, and m the mass in grams. The classical theory of impact phenomena gives the time of collision during the striking of a spring (in this case the surface of the bubble) by a mass, as: t, = 2/f = nvm/E [3] It is now possible to develop an expression for the elasticity of a floating cylindrical particle. The force equilibrium of a cylinder floating end on at the air-liquid interface is given by the well-known equation (Poisson7 1831) P = /4 D2-pL-g-h + D.y sin a [4] which accounts for the buoyancy and the action of the surface tension where P is the force acting on the particle in dynes (weight-buoyancy), D the diameter of the cylinder in cm, PL the density of the liquid in grams per cc, g the acceleration of gravity = 981 cm per sec2, h the depression of the cylinder below the surface of the liquid in cm, y the surface tension in dynes per cm and a the supporting angles or the one required to insure equilibrium, a being smaller than the contact angle 0. Although demonstrated by Poisson, it has not

Jan 1, 1953

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2'3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948