Search Documents

By P. J. Closmann

Steam zone growth as a function of time has been calculated for the case of constant rate steam injection into a preheated reservoir. To simplify the calculation a linear temperature profile has been assumed in the cap and base rock at the start of steam injection. The results indicate that at early times augmentation of steam zone growth due to preheating should be greatest. At longer times the steam zone development becomes close to that calculated with no preheating. INTRODUCTION With the increasing application of thermal recovery processes to recover viscous oil, cyclic steam injection has become important in many large-scale projects. In this process, the cycle of steam injection followed by oil production is repeated a number of times. At the beginning of the second and later cycles, steam is injected into a reservoir that has already been heated but that has lost part of its heat both in produced fluids and by conductive heat loss away from the injection zone. In such a case, the temperature level of the injection zone and the temperature distribution of the surrounding rock will affect the growth of the steam zone developed during the subsequent steam injection. Knowledge of the size of steam zone developed is important in determining the amount of oil displaced and the extent of heating in the reservoir. It is also useful to be able to compute the size of the steam zone for cases where thief zones take most of the injected steam. This paper presents a fairly straightforward method of estimating the steam zone developed in a preheated formation, based on certain simplifying assumptions. Some cases of steam injection into a reservoir at its original temperature have already been considered elsewhere.1-3 Because it is difficult or impossible to obtain an accurate representation of the temperature distribution in the reservoir some time after initial heating has taken place, in this work, a linear temperature profile in the cap and base rock is assumed (Figs. 1A and 1B). The linear profile has the advantage of yielding heat flow equations that

Jan 1, 1969

By G. Beghi, G. Piatti

THE authors examined the problem of the gradual transformation of Al2O3 from the transition phases normally encountered in SAP (r -x-n)1-3 to the stable a phase. This phenomenon is well-known at temperatures above the melting point of aluminum,3"6 whereas in this paper the transformation was studied at temperatures lower than the melting point of the aluminum matrix.

Jan 1, 1967

By William E. Greenawalt

IN these days of special legislation for the benefit of various industries one might well consider one branch of human endeavor intimately associated with engineering-that of patents and patent litigation. It is estimated that 85 per cent of all industries in the United States are based directly or indirectly on patents. Most inventors are engineers, and most patent litigation pertains to the engineering industries. It is fitting, therefore, that engineers should be vitally interested in discussing patent affairs, particularly as inventors are not a professional group, and invention is mostly a transitory phase incident to the development of specific industrial problems.

Jan 1, 1937

By NONE N

Jan 1, 1963

By Johannes Moeljono, Werner Wenzel, Heinrich Wilhelm Gudenhau

As an important mechanism for increasing production of the suction-draft-sinter process, it has been shown that gas permeability through the sinter layer plays an important role. Methods to increase production rates have been indicated and suggestions for carrying out the process have been made to improve the rate of production, reduce the fuel consumption, and at the same time obtain a uniform sinter. Laboratory experiments were conducted at the Institute for Ferrous Metallurgy of the Technical University at Aachen to illustrate these methods. Methods of Increasing Gas Penetration Through Sinter Layers The following are of fundamental importance in determining the process cycle during the sintering of iron ores: 1) Generation of maximum temperature, since its form and range determine sinter quality. 2) Propagation velocity of the temperature maximum which controls the attainable output. 3) The convective heat transfer which influences the velocity of travel of the temperature maximum.

Jan 1, 1974

By Don K. Smith

The Reclamation Program for the Northern Zone of the Indus Plains in West Pakistan involves the construction of 30,000 irrigation wells to serve 20 million acres with an annual pumpage of nearly 40 million acre-ft. Detailed hydrologic studies indicated that mild steel would be satisfactory for casing; however, within two years after construction, about 10% of the wells began to fail due to encrustation and corrosion of the casing. A search to find a noncor-rosive substitute for the steel casing disclosed that only fiberglass-reinforced plastic pipe satisfied all requirements. The results of initial use of fiberglass have been highly satisfactory and have resulted in a lower over-all well cost. Advances in technology pomise further reduction in prices and improvement in performance. The northern zone of the Indus Basin comprises a vast area of essentially level land in West Pakistan which is irrigated by means of a complex system of canals that distribute more water to more land than any other irrigation system in the world. In spite of the development of this extensive irrigation system, production of food and fiber has not met the requirements of the country. The major reasons that crop production has not reached anticipated levels are the lack of adequate irrigation supplies and effective subsurface drainage. As a result, yields per acre are among the lowest in the world for areas where irrigation is practiced, and many thousands of acres of valuable crop land have been removed from production or seriously affected by salinity and waterlogging. To rectify the problems of irrigation supply and drainage the Government of Pakistan has undertaken a program of Salinity Control and Reclamation which is being administered by the Water and Power Development Authority. The Authority retained Tipton and Kalmbach, Inc., of Denver, Colo., as engineers for the program in the northern zone of the Indus Basin. This program consists of the construction of about 30,000 irrigation wells to provide drainage for waterlogged lands and full irrigation supplies, including leaching requirements, for all cultivated lands. The program will ultimately ensure the productivity of 20 million acres and involve an annual pumpage from groundwater storage of nearly 40 million acre-ft of

Jan 1, 1970

By Richards J. W.

J.W. RICHARDS, South Bethlehem, Pa. (communication to the Secretary?).-Mr. Howland's paper, data and conclusions have interested me intensely, and have led me to study carefully the record-of his 26 furnaces therein given. Mr. Howland is undoubtedly right in his conclusion that when expressing the amount of carbon burned at the tuyères in percentage of the total

Jan 1, 1917

By Robert Thomas

DURING the past 20 years the advantages of reinforced concrete as a substitute for timbering in so-called permanent mine openings have been fully recognized, and its use has become almost general practice in the larger mines. The term "permanent mine openings" is used advisedly and is assumed to embrace such openings as ventilation shafts, material shafts and main hoisting shafts, with their adjacent stations, ore pockets, etc. In the concreting of such openings, the actual cost as compared with that of timbering has been of secondary consideration, the support of large openings, elimination of fire hazards, and prevention of inter-ruptions to production being the primary objectives. The ultimate economy, however, of lining such openings with concrete when they are to remain in use during the entire life of the mine, and especially when they are in bad ground, will seldom be questioned. During this 20-year period there have appeared in engineering publi-cations a number of interesting articles on the use of concrete in mines, nearly always describing some specific project of major proportions, such as the concreting of ore pockets, large stations or main hoisting shafts. Such articles are unquestionably of interest, since the projects require considerable engineering thought, not only in the method of excavating large openings, but in their engineering design as well. Concreting of main hoisting shafts, particularly when this is done with the least possible interruption to production, provides some interesting problems. The concreting of haulage drifts of the dimensions commonly found in mines, on the other hand, soon develops into a routine operation, there-fore it is with some hesitancy that the author attempts to prepare an article on this subject. The writer can recall only one article on the concreting of mine haulageways, although several articles have been written concerning the concreting of tunnels considerably larger in dimensions than those required in general mine practice.

Jan 1, 1936

By J. L. Lytton

The flow-stress recovery of high-purity aluminurn following a 10 pct tensile prestrain was studied in terms of a fractional flow-stress recovery parameter fr. The flow-stress recovery behavior was related to the dislocation arrangements using transmissiort electron rnicvoscopy. During recovery at 120° and 160°C, nearly stable strength levels were attained, the strength level for 120°C recovery being greater than that for 160°C. This stabilization of flow stress was related to the formation of meta-stable dislocation networks bounding nearly perfect cells. Both network formation and the annealing of dislocation loops were found to be recovery mechanisms, and the stronger metastable strength level joy 120°C recovery was related to a smaller average cell size. Analysis of the networks was consistent with the reaction of sets of dislocations with a/2 (110) Burgers vector to give product Burgers DURING isothermal annealing of cold-worked metals, a degree of softening occurs without re-crystallization, and the processes responsible for this change are termed recovery processes. During recovery annealing, the dislocations generated during cold work become rearranged into low-energy configurations, and as much as 50 pct of the stored energy is released."' The relationship between this rearrangement of dislocations and mechanical behavior is of considerable importance, since the dislocation substructures formed during recovery provide a significant degree of low-temperature strength3j4 and can favorably alter the course of primary creep at high temperatures.4 The purpose of the present study was to relate the flow-stress recovery behavior of high-purity aluminum to the substructural modifications that occur. Electron transmission microscopy was therefore employed for direct observation of dislocation substructures at various stages of recovery following 10 pct prestrain. Several investigators5-' have proposed that dislocations can become rearranged or lost during the preparation of thin foils. It was found early in the present study that the dislocation structures in the thicker regions of the foils changed in a systematic way during the course of recovery. Therefore, it is unlikely that substantial losses or rearrangements occurred during thinning. This point will be discussed in more detail later. The results of various investigators indicate that recovery processes in fcc metals can result in release of 50 pct or more of the total energy stored in the as-prestrained metal, this percentage decreasing with increasing prestrain.' Alloying elements or impurities tend to increase this percentage. The release of stored energy of fcc metals during recovery appears to occur by 1) annealing of point defects if the deformation occurred at sufficiently low temperaturesg and 2) rearrangement of dislocations into low-energy Configurations.1,2In bcc metals, the annealing of dislocation loops has also been observed during recovery after prestrain,10-12 and it has been proposed that this is a recovery mechanism for unidirectionally strained fcc metals.' The density of dislocations in bcc metals has not been observed to decrease appreciably during recovery,10 although the formation of regular dislocation networks has been observed. has shown that the formation of such networks can result in elimination of long-range stresses and can lead to significant release of stored energy without dislocation annihilation. It might thus be expected that network formation is a significant recovery mechanism in fcc metals, although extensive network formation has apparently not been reported in controlled recovery experiments. The formation of sub-boundaries in aluminum has been observed by various investigators13'17 during recovery studies of aluminum, but the structure of these boundaries was not resolved. In this regard, it is significant to note that Bailey and Hirsch,' using transmission electron microscopy, detected no network or sub-boundary formation during recovery of 99.99 pct Ag. Furthermore, Clarebrough et al.2 found no such rearrangements during recovery of copper. EXPERIMENTAL PROCEDURE The high-purity aluminum used in this investigation was obtained in the form of 0.125-in.-thick sheet. Spectrographic analysis revealed that the sheet was 99.995 pct A1 with the following weight-percent impurities: 0.001 Cu, 0.002 Fe, 0.001 Si, and 0.0004 Mg. The as-received sheet was in the heavily cold-rolled condition. The as-received sheet was cold-rolled at room temperature to 0.040-in.-thick sheet in the longitudinal direction, which was the original rolling

Jan 1, 1965

By L. E. Fish, G. S. Wyman

CHUQUICAMATA open-pit mine is capable of producing a total of 105,000 tons daily. When the sulphide plant is operating to capacity the distribution of this quantity will be approximately 30,000 tons sulphide ore, 30,000 tons oxide ore and 45,000 tons of waste. At that time the combined capacity of the oxide and sulphide plants will be about 540 million lb of copper per year. Twenty one benches have been opened to date and all are still active except the three top ones at the northeastern limit of the pit. These have been pushed back to final slope line. The pit is 8850 ft long, 3540 ft wide and 980 ft deep. Benches are not all developed to a standard height as the large development shovels used in cutting new benches have been of different size and range. At this time new benches 521 ft high are being developed with an' 11-yd shovel. Ore haulage through the greater part of the pit operation has been on down grades to the crushing plant. With the opening of bench F-4 in April 1944 the first adverse-grade ore haul was encountered. Of the total tonnage now being mined, 35 pct comes from the four benches that are below the level of the crushing plant yard. Waste had been dumped on the same or nearly the same level as the bench from which it was removed up to the opening of bench F-4. Waste from this and lower levels is hauled to the level of the crusher, yard where it must cross the flow of ore traffic to reach the only available dumping space to the east of the mine. The average ore haul is 3.13 miles one way shovel to crusher, and the average waste haul from that portion handled by railroad is 3.32 miles one way from shovel to waste dump. Waste that is being removed by truck haulage from the upper part of the -mine is hauled an average of 1 mile. Ore loaded by trucks is hauled 3/4 mile to a car loading ramp and then by rail to the crushing plant. Drilling and Blasting There are two types of development for blasting being used: One for opening new benches and the other for bank shooting. The former consists of 9a in. diam churn-drill holes drilled 11.8 ft center to center in rows 10.2 ft apart with the holes staggered in the rows thus giving an equilateral-triangle pattern of 11.8 ft on a side. After the first block, 492 ft long by 71.5 ft wide, is shot in the pattern described above, the cut is advanced by smaller shots consisting of four rows of holes spaced 23 ft center to center with the rows 23 ft apart. These shots are fired in conjunction with side shots in which the holes are drilled 33 ft center to center and 29.5 ft back from the toe, thus squaring up the bank for subsequent shooting. An average bank shot consists of about 60 holes drilled in two rows parallel to the face, 30 holes to

Jan 1, 1952

By Pervez Patel, Martin G. Frohberg, Demetrios Papamantellos

Model experiments were carried out on the mass transfer of iodine between n-hexane and a 4 2 X 10-3 M aqueous sodium hydroxide solution. The influence of mechanical stirring by means of small gas bubbles (ca. 0.01 ml in volume) on mass transfer was examined in independent experiments. The results were described with the help of the penetration theory and in the case of bubble stirring with the help of a mathematical model based on this theory. S LAG-METAL reactions, especially those in steel-making processes, often occur under conditions where gas is evolved in the form of bubbles that break through the slag-metal interface. It is known that stirring by means of bubbles increases the mass transfer coefficient, but there has been very little quantitative work done in this field. Because of the difficulties that attach to experimental work at high temperatures this study was confined to model experiments at room temperature. EXPERIMENTAL APPARATUS The transport of iodine from an n-hexane layer into a weak sodium hydroxide solution was studied a) with stirring by means of bubbles and b) with mechanical stirring. The apparatus for the experiments with bubbles consisted of the cell, two Dreschel bottles filled with hexane in order to saturate the nitrogen flow, one flow meter, and a nitrogen gas cylinder fitted with a fine-regulating valve. Fig. 1 shows the cell consisting of a glass cylinder 33 cm in height with an overall diameter of 7.5 cm embedded in a copper flange. The flange is connected to a Plexiglas plate and to the gas inlet. The Plexiglas plate has holes of 0.2 mm diam bored into it which are spaced 1 cm from each other. For the experiments with mechanical stirring the bottom of the cell was sealed off by a Plexiglas plate. The upper layer was stirred by means of a glass stir-rer and the bottom layer with the help of a magnetic stirrer in a counter rotatory direction. Both stirrer speeds could be varied continuously. EXPERIMENTAL PROCEDURE Iodine dissolves in n-hexane producing a stable violet color thus enabling the iodine concentration in

Jan 1, 1970

By P. Niessen, W. C. Winegard, C. J. Beingessner

DURING the last 10 years, several grain-growth studies have been made using zone-refined metals with controlled amounts of solute to elucidate the interaction of solute with moving boundaries. In all these studies, it was more or less implicitly assumed that the alloys used were, after recrystallization and grain growth, homogeneous within the grains with respect to solute and lattice defects. This note deals with observations made on microstructures originating from solidification of dilute alloys and from grain growth. Briefly, the experimental procedure used in these studies was the following: zone-refined cadmium and master alloys were melted and cast in Pyrex under vacuum to produce bars 14 mm in diam and about 150 mm long. These bars were cut into 8-mm-thick slices which were mechanically and chemically polished. The specimens were then deformed 30 pct in compression and given a 1-week anneal at 260°C in argon. After this anneal, a second deformation produced completely recrystallized samples 4 mm thick. The time-temperature controlled anneals were carried out in a bath of silicone oil. After the grain-growth anneal, the specimens were polished in Gil-man's' solution (33 g CrOs, 6 g NazSO, in 100 ml of water). Several etches were used depending on the alloy investigated, but mostly a mixture of concentrated HC1 and HNOj (98:2 vol) was employed. In all the alloys examined, the ease with which substructures could be revealed depended strongly on the crystallographic orientation of the surfaces of the grains. However, very frequently the microstructures to be discussed here etched up over broad areas comprising several grains. Fig. 1 is a micrograph of a Cd-0.05 at. pct Mg alloy annealed for 100 sec at 270°C. Different substructures are seen in this photograph. A denotes the now existing grain boundaries. The well-defined lines and points marked B are the remains of a solidification substructure. The lines are boundaries between cell colonies, and the points are nodes located on regular two-dimensional cells. This cellular structure has the same appearance as that found by weinberg2 for rapidly quenched Zn-Au alloys. The "ghost boundaries", marked C, are very similar in appearance to a grain boundary array in a polycrystalline sample. Repeated polishing and etching showed that all the substructures observed were three-dimensional. To date, the ghost boundaries have been clearly observed in all samples containing 0.005, 0.01, 0.05, and 1 at. pct Mg, and in samples containing 0.01 at. pct Zn. Attempts to outline these ghost boundaries in cadmium alloys containing 0.01 at. pct Ag and Au were only partially successful. In these alloys, parallel lines, having a resemblance to the ghost boundaries in the Cd-Mg and Cd-Zn alloys, were observed, but it was not possible to obtain complete arrays of ghost boundaries which extended over several grains. It is possible that a different etch than that presently employed would reveal the ghost boundaries in the Cd-Au and Cd-Ag alloys as clearly as in the Cd-Zn and Cd-Mg alloys. A close examination of the ghost structure showed that it consisted of linear etch-pit arrays, Fig. 2. The ghost boundaries were resolvable even in grains which showed over-all faceting due to the etching, as seen in the corner of Fig. 2. The general appearance of the ghost structure suggests that it originated during grain growth. This is supported by the observation that the mesh width in the ghost-boundary array generally increased with increasing final grain size. To test whether the ghost structure was formed during the long homogenizing anneal or during the grain-growth anneal, some as-cast samples were deformed and given a grain-growth anneal. This anneal was terminated by air cooling or

Jan 1, 1967

By William I. Busenbark, Elmer C. Newman

At Bingham Canyon, the world's largest open-pit copper mine, annual grease consumption is in the neighborhood of 109 000 kg (240,000 lb), all of which was 544 (120-16) purchased, warehoused, and distributed in 54-kg (120-1b) and 180-kg (400-1b) drums. While perhaps a menial and mundane chore, grease distribution shows on the ledger as a significant expense item. To improve labor and cost performance, Kennecott maintenance engineers undertook a study to find the most direct method for moving multi purpose grease (MPG) from the refinery to the point of final consumption. What they found was a direct vendor system for hulk grease so simple and flexible that long-established drum distribution is being phased out in favor of the newer method throughout 75% of the operation.

Jan 9, 1977

By T. D. Parris

Within a 30-mile radius of Sudbury, Ontario, the Ontario division of the International Nickel Co. of Canada, Ltd., operates nine underground mines and two open pits. Prior to 1966, ore removal from the underground workings was mainly by scraping, using 125-hp electric slushers in blasthole and caving mining, and 30-hp or less air-operated slushers for fill- method mining. The development and evaluation of low-profile, diesel-powered front-end loaders, designed specifically for underground operations, was followed with keen interest during the period 1964-1965.

Jan 6, 1969

By F. W. Bowdish

Analysis of data on the equilibrium exchange of sodium ions from salt solutions for calcium ions, from various fractions of an oxidized calcareous iron ore from Lorraine, France, strongly suggests that the calcium may be attached to the solid by only one of its bonds. Nearly equal values were found for the equilibrium expression from data covering concentration ranges of 1000 fold for the salt and 235 fold for the ion-exchangeable calcium. Differences indicated between the exchangeable calcium contents of the slime and the sandy portions of the ore, as well as the equilibrium relationship itself, are of importance in the flotation of the ore. During an experimental program on the flotation of oxidized calcareous iron ores from Lorraine, France, ion-exchangeable calcium was found in the ore. Because this source of calcium ions, if not controlled, could thwart all efforts at flotation, an extensive study was made of the phenomenon. The part of that study reported here was to obtain data on the equilibrium established between ore solids and solutions of sodium chloride, and to analyze the data to try to understand better the physical chemistry of the exchange. The ore contains oolites of goethite and quartz grains embedded in a matrix consisting of calcite and a brown cement believed to be the residue from oxidation of the silicate minerals found in fresh unoxidized ore. When ground, a substantial fraction of the ore becomes a fine slime in which is concentrated more than half of the alumina content of the ore. It is believed that the alumina occurs as unidentified clay minerals with which most of the ion-exchange capacity of the ore is associated. A preliminary experiment on the exchange of ions from the ore for sodium ions from solutions of NaCl showed that calcium was about ten times as abundant as magnesium in the exchange solutions. Thus calcium was the predominant ion in causing difficulties with flotation, and it was the only one for which data was obtained in this study. It is believed that the omission of magnesium ion exchange from consideration does not invalidate the results. It is possible, however, that inclusion of magnesium in the analyses and calculations or its prior elimination from the samples would have improved the consistency of the results. EXPERIMENTAL Data about the equilibrium exchange of sodium from solutions for calcium from the solids were obtained using two different samples of material. The solids

Jan 1, 1963

By James F. Kemp

Jan 1, 1914

TO THE. BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the report of the Treasurer for the year 1945 and reports for the same year of the following committees: Membership, Admissions, Papers and Publications, Mining and Metallury (Magazine), and Library. In this review of the year by the Secretary reference frequently will be made to the "Paul" Committee and to the "hotter" Committee. The first is the special committee on Divisional Relationships and the second the special Committee on Ways and Means. These two important committees, appointed by President Harvey S. Mudd under authorization of the Board of Directors on March 21, 1945, were composed as follows:

Jan 1, 1946

By D. L. King, C. D. Rubert, R. W. Christy, B. A. Schepman

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963

By D. E. Stephenson. Discussion by R. G. K. Morrison, L. Obert

R. G. K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que., Canada) - The discing of drill core has been a recognized pressure phenomenon for many years but only recently has an interest been taken in the mechanism involved. The work of Jaeger and Cook is referred to in the text. The authors have now advanced the study to establish, within certain loading limitations, a direct relationship between axial and radial stress at failure. This is an important contribution. In mines generally, where pressure conditions result in the spalling of openings, the faces of drifts and crosscuts, on scaling, usually show a concavity with respect to the opening very similar to the face of the drill hole after the separation of the stub. The same holds for shaft sinks. This suggests a similarity between the mechanism of the discing of core and that of the spalling of an opening, under pressure, to develop a more stable outline. The latter, commonly regarded as shear, is the most conspicuous type of failure observed in

Jan 1, 1967

By C. E. Gerity

Near Bunker, Mo., in the New Lead Belt, Ozark Lead Co. operates a 6000 tpd lead-zinc mine. Mined ore is transported to the surface in three mechanized and automated steps. The mine is developed by a rectangular-shaped sublevel haulage drift 15 ft high by 28 ft wide, driven on strike below the ore zones. Ore transfer raises were driven from the sublevel at locations near the shaft, 1500 ft distant, and on subsequent 1000 ft centers. These 6 x 5-ft raises are slashed to obtain maximum storage below dump points. These dump points are located on each mining level and are of steel and concrete construction. Spiral 12 X 24-ft inclines driven from the sub-level provide access to these levels for equipment and mine utilities.

Jan 11, 1972