Search Documents

By W. W. Wirth

RESEARCH looking toward the reduction of the cost of roof support by substitution of longer-life materials for wooden timber is fully justified by the fact that roof support is an important element of all production costs. Permanent or semipermanent roof support will reduce the expense of timber-maintenance crews during steady operations, but even more markedly during idle periods. The management, therefore, is faced with the important problem of timber renewals, which in times of regular operation are frequently obscured by more urgent problems of production. Increased use of timber in the Anthracite Region of Pennsylvania is caused mainly by increased percentage of coal obtained from robbing areas, which requires more timber for safety than develop-ment work, and maintenance of long haulageways through crushed ground despite the fact that less coal is transported over them. The timber reserve in the immediate vicinity of the mines has been depleted to such an extent that it is necessary to secure 70 per cent of the timber requirements from distant sources. Originally, mine timbering in this region was done by largely utilizing round props or legs with round collars. The whole cross section of the tree from which timber was cut was utilized by forming the joints between the legs and the collars with saw and adze, using plank or round saplings for lagging behind the legs and over the collars to prevent material falling between them. The Mine Inspectors' report of 1898 records an important digression from the use of round timber, when two tunnels at the Babylon colliery, near Pittston, Pa., were timbered with 12 by 12-in. square timber sets with mud sills, through quicksand for distances of 425 and 160 ft., respectively. The timbers were lagged with 3-in. plank to control sand.

Jan 1, 1940

By W. Chubb

By measuring the hardness of metals at temperatures just above and just below their allotropic change point, it has been established that crystal structure has a real effect upon the strength of metals. The DPH of cobalt, iron, titanium, uranium, and zirconium have been measured at temperatures up to 1000°C. It was found that the body-centered-cubic crystal structure is always the softer structure when it is involved in an allotropic transformation. The close-packed and more complex structures are inherently harder, and may be expected, therefore, to be better base materials for high strength alloys. IT has been observed that for metals with nearly the same melting point (i.e., tin and lead, magnesium and aluminum) the metal with the more complex crystal structure has a higher tensile strength and hardness. It might be asked whether this effect is really caused by the difference in crystal structure; and, if so, just what is the contribution of crystal structure to the strength of these metals. A qualitative answer to these questions can be obtained by measuring the change in hardness produced by the change in structure in metals exhibiting allotropic forms. The evidence for changes in mechanical properties during allotropic transformations is rather meager. In 1909, Rosenhain and Humfrey' observed that "ß" iron showed much less deformation at the transformation temperature than a iron. By means of a torsion test, Lee found that iron bars were "critically plastic" at the a-7 transformation temperature. Sauerwald and Knehans have shown that the dynamic hardness of iron increases between 900" and 1000°C. In 1930, Albert Sauveur' presented data on the hardness, tensile strength, and torsional strength of pui-e iron up to 1000°C. He concluded, "At 900°C, the a iron transforms into y iron, and this is accompanied by increased strength and stiffness and decreased ductility." The same year, Schischokin" obtained data on the hardness of thallium at temperatures above and below its transformation temperature. His data are replotted on semilogarithmic coordinates as Fig. 1. The fact that his data fall on straight lines in this type of plot is believed to attest to the purity of his metal and the accuracy of his results. In 1941, Nadai and Manjoine" obtained tensile data on pure iron with an indicated increase in strength at about 900°C. These experiments make it quite evident that changes in mechanical properties occur when a metal transforms from one crystal structure to another; but, except for Schischokin's data on thallium, none of the measurements seem accurate enough to determine the relative magnitude of the mechanical property change. Materials The metals that have been examined for changes in hardness during transformation include l—as- deposited commercial electrolytic cobalt about 99.7 pct pure, 2—Armco ingot iron, 3—are-melted iodide titanium of a purity in excess of 99.8 pct, 4—uranium of a purity in excess of 99.5 pct, 5—are-melted iodide zirconium of a purity in excess of 99.8 pct, 6—annealed, 0.08 pct C, rimmed steel, and 7—commercially pure RC55 titanium. While the purity of the first five of these materials leaves something to be desired, it will be noted that the observed hardness discontinuities occurred at the accepted transformation temperatures. (These temperatures are indicated by vertical arrows in Figs. 1 and 3 through 7.) The last two materials are commercial alloys introduced to show the effect of minor alloying elements upon the hot hardness curve. Apparatus Hardnesses at elevated temperatures were determined by means of a vacuum hot hardness machine. A diagram showing the basic features of this machine appears as Fig. 2. This machine is essentially a deadweight hardness .machine in a furnace within a vacuum chamber. The sapphire-tipped indentor

Jan 1, 1956

By H. Vincent Wallace

ALTHOUGH it is universally accepted that free oxygen is A necessary in a cyanide solution for the dissolution of gold and silver-in accordance with Elsner's equation that 2Au + 4KCN + 0 + H20 = 2KAu (CN), + 2KOH- little has been written and insufficient attention paid to the drop in extraction due apparently to loss of dissolved oxygen in mill solutions. Aeration or oxygenation of cyanide solutions has been more or less successfully accomplished by various types of agitators such as the Dorr (with or without air lifts), Pachuca tanks and more recently "Turbo-mixers" and Denver "Super- agitators"; also by the introduction of chemical oxidizing agents such as Solozone (Na,O,) . At the Wright-Hargreaves and other mines in the Kirkland Lake camp, the introduction of this reagent at the rate of about 1.25 oz. per ton of ore applied to the feed of the ball mills has certainly been beneficial.

Jan 1, 1932

By George J. Young

(Cleveland Meeting, October, 1912.) I. GENERAL. THE recurrence of mine-fires in Nevada during the past decade is not only a matter of interest, but also one of considerable concern to engineers and mine-managers. The more important fires may he enumerated as follows: Forman Shaft fire., Gold Hill, April 21, 1903 ; shaft-house, machinery, and shaft, destroyed; loss estimated at $50,000.; Cause Unknown. Union Shaft fire, Virginia City, July 14, 1904; shaft-house, machinery, and shaft in part destroyed; loss estimated it $100,000; cause of fire stated as the careless throwing of a match in the rope-house. Sutro Tunnel fire, Virginia City, Jan. 27, 1909 ; 700 ft. of tunnel-timbering destroyed, and direct damage of $10,000; cause ' probably electric wires." Belcher Shaft fire, Gold Hill, Aug. 9, 1910; shaft-house destroyed, machinery ruined, and upper part of shaft damaged; damage, $25,000; no cause given. Belmont Mine fire, Tonopah, Feb. 23, 1911; fire started in winze ; 17 men killed. Giroux Mine fire, Kimberly, Aug. 23, 1911 ; fire originated iii shaft-station from unknown cause; 7 men killed, and $34,¬521 damage caused. (NOTE 1.-On June 11, 1912, some time after the present paper was written, a fire broke out in the pump-room on the 2475 station of the Ward shaft, Virginia City. This fire was caused by the short-circuiting and exploding of the starting-switch on No. 5 pump. The oil in the switch was scattered about and set fire to the timbers and laming of the pump-room. The pump-roan in charge notified the surface, and the * Professor of Mining and Metallurgy, Mackay School of Mines.

Oct 1, 1912

By Edward H. Robie

MANY engineers currently are working harder than usual, in part because of the demands being made upon them for increased production in the war effort, and in part because engineers are in short supply so that there is more to do for those who are available. In some instances the question has come up as to what additional payment, if any, should properly be made for overtime work, and to what extent is such payment legally permitted under the rules of the Salary Stabilization Board. Most engineers employed in an executive, administrative, or outside salesman capacity are not paid for overtime. They are paid for doing a job instead of for the hours they put in, and are free to do all the unpaid home work they feel they should do after dinner, as well as to do a bit of thinking and worrying during wakeful hours in bed. But engineers employed in a strictly professional capacity normally have standard office hours. Some employers pay for overtime and some don't. Their practice as it existed on Jan. 25, 1951 may be continued. In the absence of such practice at that time, the Salary Stabilization Board says that the engineer may now receive additional compensation up to his straight-time rate for an extended work week. No formal approval of the Board is required. "A professional engineer," in the mind of the Board, "is a person employed in a professional capacity, who, by reason of his special knowledge of the mathematical and physical sciences and the principles and methods of engineering analysis and design, acquired by professional education and practical experience, is qualified to practice engineering." Inducted Engineers A letter from a young man just inducted into the service and fearful that his engineering training is not going to be utilized reached us last week from Fort Riley, Kan. The AIME, cooperating with the other Founder Societies, is doing what it can, through the Engineering Manpower Commission, to see that engineers are not being wasted in the military establishment. So we passed this young man's letter along to T. A. Marshall Jr., executive secretary of that Commission. Mr. Marshall tells us that the normal procedure now being followed by the Army in handling Selective Service inductees is to have them first complete 16 weeks of basic training before assignment to specialized categories. During that time they are classified. If one has an engineering degree he should be classified as scientific and engineering personnel at the end of the basic training period. He should then be transferred to a technical detachment and assigned an MOS (Military Occupational Specialties) reflecting his education. If a young man is looking for a commission, it might be added that the current policy in the Army is to transfer to OCS (Officer Candidate School) applicants for commissions in the infantry only. The local unit commander can give information on this point, based upon the aptitude shown in tests. In view of the current shortage of engineers, it is believed that a young man should seriously consider remaining in enlisted status unless he can obtain a commission in a branch of the service that can make full use of his technical skills. His work may thus be more to his liking even if his uniform is not. New York or Atlantic City? In which place is it preferable to hold the annual meeting of a professional society like the AIME-New York or Atlantic City? That is, a winter meeting. The American Society of Mechanical Engineers has held its recent meetings at Atlantic City, with increasing attendance and satisfaction. The American Institute of Chemical Engineers chose Atlantic City for its recent December annual meeting. Only twice has the AIME ever met in this famous seashore resort: in 1898 and 1904. Chief advantages of going to Atlantic City over New York are that technical sessions are better attended, there being little else to do there in Winter; the cost to members is less, and hotel facilities are better adapted to a large meeting. As to cost, take a banquet, for instance. The Chalfonte-Haddon Hall, which caters especially to winter conventions, charges about $7 for a banquet dinner of standard quality. A similar dinner at the Statler in New York would cost about $8.50, and about $10.50 at the Waldorf-Astoria. (The charge for tickets is somewhat greater than this because of the cost of music, programs, flowers, and other incidentals.) Rooms, too, are somewhat less at Atlantic City, two in a room being accommodated for about $7 per day each, compared with $7 to $10 at a headquarters hotel in New York. On the other hand, AIME headquarters is put to some extra expense for staff travel, food and lodging, and members living in New York and environs are forced to pay a hotel bill. New York, of course, has more varied amusements to offer, plenty of big stores, and the glamour of a big city. The choice may be discussed at the forthcoming meeting in New York. In the meantime if any reader cares to express an opinion one way or the other we shall be glad to hear it. College Scholarships Most parents of children in the later stages of high school find it necessary to give some consideration to the cost of a college education. Although salaries have increased substantially it seems that the cost of the necessities of life, such as food, housing, and maintaining the family automobile, have gone up even more, so the problem of financing the children's education is as acute as ever. Many overlook the possibility of scholarships, or feel that only a student at or near the top of his class has a chance to get one. As a matter of fact, close to 150,000 scholarships and more than 15,000 fellowships, worth some $42,000,000, are available in 1200 American colleges and universities. Those who are interested should send 55¢ to the Superintendent of Documents, Government Printing Office, Washington 25, D. C. for a 248-page publication just issued by the U. S. Office of Education, entitled "Scholarships and Fellowships Available at Institutions of Higher Education."

Jan 1, 1952

By T. L. Joseph, G. Bitsianes

The gaseous reduction of dense iron ore is a topochemical process in which reduction takes place at distinct interfaces between solid phases or layers. Under normal conditions, these interfaces remain parallel to the exterior surface of the ore body as they move inward. Certain conditions, such as cracking, high porosity, impurities, entrapped residual oxides, may cause departures from normal topochemical behavior. THE gaseous reduction of dense iron ore proceeds at interfaces between several solid phases or layers.',' Under normal conditions, these interfaces progress inward and remain parallel to the exterior surface of the ore body. This topochemical behavior is clearly illustrated in Fig. 1 which shows partially reduced specimens of natural and synthetic hematite. Using a coordinated sequence of macro, micro, and X-ray examinations, the authors1-'2 found that the number of interfaces and participating phases was in agreement with the Fe-0 system. Above 570°C, reduction of the ore involved a maximum of three common boundaries between four solid phases: iron, wiistite (Fe,O), magnetite (Fe,O,), and hematite (Fe,O,). Below 570°C, reduction proceeded through two interfaces between three phases: iron, magnetite (Fe,O,), and hematite (Fe,O,). The decrease in the number of phases below 570°C was due to the instability of wiistite below this temperature. The sequence of phases was also consistent with the equilibrium requirements. For example, the layers of iron oxides that were formed in topochemical fashion were always orientated in the order of increasing oxygen content. Thus, in Fig. 1 an outer layer of metallic iron is followed in turn by a thick intermediate band of black wiistite, by a thin layer of light magnetite, and finally by a relatively large core of hematite. This arrangement of the oxide layers was due to restrictions in reducing conditions which were imposed by the physical structure of the solid. The highly reducing gas on the outside of the particle gradually lost its reducing power as it penetrated into the specimen. On a macro scale, the layers of the various oxides appeared to be sharply defined and uniform in composition. Microexamination of the sections, however, revealed that the interfaces did possess measurable widths which varied with the porosity and chemical activity of the oxide phase undergoing reduction. For example, Fig. 2 shows three interfaces in a dense hematitic ore which was partially reduced at 850°C. At the iron-wiistite interface where the greatest porosity developed, the reaction proceeded over a zone 25 to 30 microns in width. Toward the interior, the interfaces became progressively narrower until at the magnetite-hematite boundary the reaction zone was about 1 micron wide. In this region the structure was exceedingly dense; the hematite possessing a porosity on the order of 3 pct. A careful micro study across polished layers of the various oxides revealed generally homogenous and single-phase structures. As reported in a previous paper,' the wiistite layer was characterized by an increase in oxygen content with depth of penetration. The topochemical behavior of reduction was studied in six types of ore of different origin, composition, and physical structure. In most cases, reduction proceeded at the boundaries of well defined layers or phases, and this behavior may be regarded as normal for most dense fine grained ores. Deviations from Ideal Topochemical Behavior A number of deviations from the normal topochemical behavior were noted. In these cases, the continuity of the reduction interfaces was disrupted in one of four ways: 1—Cracking of the specimen interrupted the geometric configuration, and the interfacial advance was no longer parallel to the exterior surface. 2—As a result of high porosity, the interfaces were spread over an appreciable distance and all but obliterated. 3—Impurities in the ore promoted a variety of deviations, including cracking. 4—A residual oxide phase was entrapped in the reaction product and left behind the advancing macro interface. Results from Cracking: A crack leading into the interior of an ore specimen presents a path of least resistance for the counter-flow of reducing gases and gaseous reduction products. Higher reducing conditions can be maintained along such cracks and reduction accordingly will propagate well ahead of the normally advancing reduction interfaces. Cracking was caused by a number of factors, one of which was the thermal spalling of impurities in the massive form. A more general type of cracking was due to reduction and was found in all dense varieties of natural and synthetic hematite, particularly in the temperature range of 500" to 700°C. The effect is shown clearly in Fig. 3. In this case, a dense sphere of pure hematite was partially reduced at 650°C for 100 min. The macrosection shows that one large reduction crack had penetrated the specimen and disrupted the normal topochemical advance of the interfaces. The outer layer of iron was only slightly affected but the thin dark layer of wiistite, adjacent to the ferrite, had widened perceptibly as it progressed along the crack. Farther inward, the magnetite layer was greatly disrupted and had penetrated irregularly to form islands of unaltered white hematite. A great deal of internal cracking is evident in the magnetite phase. From a practical point of view, the cracking of dense ores in the blast furnace could lead to desirable as well as undesirable effects. The general result

Jan 1, 1956

Lead-zinc production in Canada accounted for 19% of the total value of metals and minerals produced in 1976, says Keith C. Hendrick, president of Noranda Sides Corp. Mine production of recoverable zinc w as 1. 158 million toils of 27.4% of free world production in 1976. Slab zinc pro¬duction was placed at 472,000 tons that year. Canadian mine production of recoverable lead was 247,000 tons or 10.6% of the free world production. Refined lead that year was at 177,000 tons.

Jan 11, 1977

By L. R. van Wert

CAREFUL research into the nature of the metallic state has yet to discover, with any certainty, its essential quality. We do riot yet know, for sure, what it is that makes the metallic elements different from, if not actually unique among, all created things. We do know, of course, that metals have certain more or less characteristic properties-they are hard, strong, and tough, and good conductors of heat and electricity, and these so-called metallic properties provide a definition of a sort. How- ever, it is the structure rather than the behavior of the metals which gives the really fundamental information necessary to the understanding of metallicity. But this information is not easily obtained. Nature has a way of keeping secrets. But happily we do possess some knowledge of how a metal is built up, and it is this matter, rather than the presentation of a formal definition, that will be discussed here.

Jan 1, 1937

By T. D. Mueller, H. Dykstra

This paper describes a method for obtaining compositions of gas and oil phases in equilibrium with each other at a given reservoir temperature and pressure as lean or enriched gas is injected into a reservoir oil not in equilibrium with the gas. The method is based on calculation of equilibrium constants, K, from the equation log Kp = A + B F, where p is pressure and F is component characterization factor. A and B are constants that vary with a composition parameter. The paper explains how A and B could be determined with a minimum amount of data. The method consists of calculating equilibrium constants as a function of liquid composition and using the K's to calculate changes in compositiort of injection gas as it successively contacts original resetvoir oil at the gas-oil front and the change in composition of reservoir oil as it is successively contacted by the injection gas in the vicinity of an injection well. An iterative process is required. Two examples of the method are given which show how oil and gas compositions and properties are calculated with the aid of a computer. INTRODUCTION The calculation of recovery from lean-gas or enriched-gas injection into a saturated or under-saturated reservoir oil requires a knowledge of how phase properties change in a reservoir between injection well and producing well. To determine the phase compositions or properties experimentally would be difficult and time consuming, especially if one wanted to look at the effect of various injection gas compositions. For some fields an engineer would want to make preliminary calculations on the economics of gas injection before he makes the decision to spend a corrsiderable sum of money for laboratory work to obtain the necessary fluid properties. A method for calculatine compositions and properties based on a minimum of laboratory data is described. The minimum amount of data required is injection gas and reservoir oil composition and injection gas solubility as a function of pressure for an undersaturated oil, or the compositions of mixtures of reservoir fluid with two or more enriched gases, which mixtures have a bubble-point pressure that is the same as the expected average displacement pressure. On the other hand, if the economics appear to be attractive, more laboratory data can be obtained in the form of equilibrium constants for three or more mixtures of the reservoir fluid and injection gases. The method is based on the calculation of K's from the equation, log Kp = A + B F, where K is equilibrium constant, p is pressure and F is component characterization factor. This method of plotting K data by means of the above equation is described by Hoffman, Crump and Hocott.1 A and B are constants that vary with a composition parameter. It is shown how experimental data are used to determine how A and B vary with composition. BASIS OF METHOD EQUILIBRIUM CONSTANTS Equilibrium constant (K) data are required for this method. The K of each component is obtained from an equation that gives the product of K and pressure as a function of component characterization factor. The characterization factor F = b(l/Tb — l/T), where b is a constant characteristic of a given component, Tb is the boiling point in OR at atmospheric pressure of the given component, and T is the temperature of the system in OR. This method of plotting K data is described by Hoffman, Crump and Hocott.l The straight-line equation of the log Kp - F plot is log hp = log Kop +BFi, where Kop is at F =0, i designates the component, and B is the slope of the line. The factor F can be

Jan 1, 1966

By J. E. Hilliard

AS is well-known, the length per unit volume, Lv, of any lineal feature (such as grain edges in a polycrys-talline specimen) can be estimated from a count of the number of point intersections with a random plane of polish. Specifically:' Lv = 2NA in which NA is the expected number of intersections per unit area of the plane. As with all other measurements in quantitative metallography, the estimation of Lv is subject to a sampling error, the magnitude of which will depend on the number of observations. The analysis is usually performed by counting the number of intersections falling within a closed test figure of known area applied to a succession of different areas on the plane of polish. The test figure can be drawn directly on the screen of a projection microscope or else superimposed on the image of the structure by means of a reticule in a focusing eyepiece of an ordinary microscope. The use of micrographs is very inefficient unless, as in the present study, these are also needed for some other purpose. Consider an analysis in which n applications are made of a test figure within which the expected number of intersections is N. The expected total number of intersections counted is then given by NT = nN If (N) is the standard deviation in N for one application of the figure and if the latter is applied to non-overlapping regions so that the N's are independent in the statistical sense, then the standard deviation in Nt is given by: a(NT) = a(N)vn Eliminating n from Eqs. [2] and [3] we obtain: Thus, k will be a constant for a given specimen and test figure. From Eqs. [ I] and [4] we find As is to be expected, therefore, the fractional error in the estimation of Lv is inversely proportional to the square root of the total number of intersections counted. It is very desirable to have at least a rough estimate of k before starting an analysis, since it will then be possible to decide in advance by use of Eq. [5J how many counts should be made in order to achieve the desired accuracy in Lv. Without such information the investigator, unless lucky, will either do needless (and tedious) work or else obtain a result with too large an error. It is very easy to calculate k for the limiting case of N — 0, i.e., when the test figure is vanishingly small. In this case there is a negligible probability of two or more intersections falling within the figure. There are therefore only two possible outcomes: a count of one with a probability of, say, p and a zero count with a probability of (I-p). Thus and Therefore: We might expect k to depend on N and therefore on the size of the test figure. Such a dependence was observed2 in the analogous case involving the estimation of grain-boundary area per unit volume by a count of the number of intersections of a test circle with traces of the boundaries on the plane of polish. In this case the theoretical value of k at the limit N — 0 was 1.41. It was also predicted that k would display an initial sharp decrease with increasing N. Experimentally, k was observed to decrease to a value of 0.62 at N - 6 and thereafter remain approximately constant. Furthermore, the value of k for N > 6 was found to be insensitive to the form of the structure provided no pronounced anisotropy or grain-size variation was present. In order to determinewhether k would exhibit a similar dependence on N in the estimation of grain-

Jan 1, 1967

By J. O. Brittain, E. Lautenschlager

Yield point measurements were made on polycrys-talline specimens of a iron deformed various amounts at 770, 1950, or 273°K, aged, and redeformed at 77: 195°, or 273°K. When the prestrain temperature is lower than that subsequent to aging, the yield point return is suppressed relative to specimens deformed at the same temperature both before and after aging. The degree of suppression is a function of both the magnitude of prestrain at the lower temperature and the difference between the deformation temperatures before and after aging. It is proposed that the suppression is caused by the formation of dislocation barriers during the initial low-temperature deformation. The aging kinetics of polycrystalline a-iron wires deformed at 77o or 303oK were studied at 44 " and 64 "C using internal friction measurements. No change was noted as a result of the difference in prestrain temperature. IN an earlier investigation1 it was observed that the return of the yield point was suppressed when a poly-crystalline specimen of a iron was plastically deformed at 77oK, aged at room temperature, and subsequently tested at room temperature. In order to investigate this observation, a research program was undertaken to measure the effect of prestrain temperature on the strain aging of a iron.' According to Thomas and Leak,3 return of the yield point and internal friction are similar measures of strain aging since both are dependent on solute atoms leaving the solid solution. The decrease in internal friction as a function of aging time is indicative of the removal of solute atoms from the solution, while the return of the yield point as a function of aging time gives the rate of arrival of solute atoms at the dislocations. According to Cottrell and Bilby,4 the solute atoms create an "atmosphere" which locks the dislocations and causes a return of the yield point upon restraining. In this experiment, both methods of measuring strain aging were employed in order to have two independent measurements of the strain aging phenomenon. In a previous study,5 the strain aging kinetics of a similar lot of a iron were measured for specimens which were prestrained and tested at the same temperature over the range of 77" to 273°K. Although some differences were found in the correlation of the two methods employed for measuring strain aging, the kinetics of strain aging were unaffected by the change of prestrain and test temperature. In another study,6 dislocation line tension and the density of the solute atmosphere were found to contribute to the return of the yield point when ingot iron specimens were prestrained at 303°K and tested at a lower temperature, namely 77°K. This paper is concerned with changes in strain aging kinetics produced by pre-straining at 77" to 303°K and testing at either the prestrain temperature or at higher temperatures up to 273°K. EXPERIMENTAL PROCEDURE The polycrystalline a iron specimens used in both the tensile and internal friction tests were 0.033-in. diam ingot iron wires, wet hydrogen treated and re-carburized. A more detailed procedure for processing a 3/16 in. ingot iron rod (nominal wt. pet composition: Fe - 0.013; C - 0.0125; Mn - 0.023; Si -0.005; P - 0.0023; S - 0.11; Cu - 0.004 N) to 0.033 in. diam specimens containing approximately 0.020 wt pet C and no detectable nitrogen with a grain diameter of 0.033 to 0.040 mm is given elsewhere.5 Immediately prior to testing, specimens were solution treated for 15 min at 700o ± 2°C in a static vacuum of less than 50 ?. of Hg and rapidly quenched into an ice-water bath while still enclosed in a 3 mm quartz vial. The internal friction specimens had 8-in. gage lengths and the tensile specimens had 2-in. gage lengths. The wires used as tensile specimens were first run as internal

Jan 1, 1962

By Charles Clayton

IN connection with certain coöperative work carried on between the Ordnance Department of the U. S. Army, the U. S. Bureau of Mines, and the U. S. Geological Survey during the year 1918, it was the writers' privilege to make metallographic examinations of a great many test bars and other pieces of nickel-steel gun forgings. The material studied came from many different steel plants throughout the country and consisted both of forgings that had been accepted by the Ordnance Department and those that had failed to pass the specified physical tests. In general, these tests require a minimum tensile strength of 95,000 lb. (42,091 kg.), an elastic limit of 65,000 lb. (29,483 kg.), an 18 per cent. elongation, and a 30 per cent. reduction in area. An average chemical composition of the steel studied is 0.38 per cent. carbon and 2.9 per cent. nickel. The steel was of both basic electric and basic open-hearth manufacture. The object of the metallographic work was two-fold: to assist in detecting defects in the steel and, if possible, to suggest remedies for the same; and to obtain as much information as possible in regard to the relation of the microstructure of the metal to its physical properties. The greater part of the investigation was devoted to defective metal that failed to pass the ordnance specifications. Many types and kinds of more or less serious defects thus came under observation, but most of these were due to the attempts by the manufacturer to meet the enormous demand for ordnance steel with more or less inadequate equipment, and were soon remedied. Two defects, the so-called "flakes" or "snowflakes" and a certain "fibrous" or "woody" fracture, were encountered so frequently and were so disastrous to the steel that the greater part of the study was devoted to them. As a result much information as to their nature and their effects

Jan 2, 1919

By J. E. Dreier

The Pachuca - Real del Monte district has produced about 46.6 kt (51,300 ton) Ag from subvolcanic vein deposits. Three types of wall rock alteration are spatially related to the veins: K-feldspar, propylitic, and phyllic. K-feldspar alteration occurs within veins; propylitic alteration occurs in fractured rocks between veins; and phyllic alteration occurs above veins. Concentrations of some trace elements in altered rocks relative to unaltered rocks are summarized below. [ ]

Jan 1, 1983

By George M. Fowler, F. E. Gregory, William M. Agar, Joseph P. Lyden

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

By William M. Agar, F. E. Gregory, Joseph P. Lyden, George M. Fowler

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

By F. E. Gregory, George M. Fowler, William M. Agar, Joseph P. Lyden

The fact that most of the zinc-lead ores of the Tri-State district are associated with abundant chert in the Boone formation has led us to give much consideration to the manner of occurrence of the chert throughout the formation and to its relationship to the structural and other geologic features having bearing upon the sulfide mineralization. Necessarily the question of the source and the manner of deposition of the chert has come up in the course of these studies. We do not pretend to have arrived at the answer to all the questions regarding the chert. However, we have made a very large number of field observations, which present certain facts about the chert in this district that may be worth elaboration. Whatever theories may be drawn upon to explain the presence and distribution of the chert must necessarily be capable of reconciliation to these facts. The more important theories that have been presented are briefly summarized, and some of them discussed, in this paper. This paper is in three distinct parts, each complete in itself, wherein is recorded the evidence gained from three separate methods of attack. In an earlier paper,(3)‡ we briefly described the chert and its relation-ship to the ore deposits. Chertification, as used in this paper, means the replacement of limestone by introduced silicic acid. It is a common phenomenon in many widely distributed limestones. The products of chertification may be chert, cotton rock, or tripoli, depending upon the extent to which the replacement has been carried. Chertification is used instead of silicifica-tion in order to reserve the latter for the siliceous emanations so common in connection with the sulfide ore deposits of this and many other districts. Broadly, it is meant to include all silicification in this district prior to the introduction of the jasperoid, the latter being contemporaneous with the ore-bearing solutions.

Jan 1, 1935

By A. C. Fraker, H. H. Stadelmaier

In the systems Mo-Fe-C, Mo-Co-C, and Mo-Ni-C the phase boumdaries of the cubic Ij carbides were determined at 1000°C and the variation of the lattice parameter with composition was measured. In the system Mo-Fe-C a single ternary carbide, Mo3Fe3C, was observed. In Mo-Co-C and Mo-Ni-C two new n phases of the type M12C were found: Mo6C06C and Mo6Ni6C. At 1000°C they coexist with the M6C phases MO3-4,CO3-2C and Mo3-4Ni3-2C, respectively. Mo3C03C and Mo4C02C are not separate phases but parts of a single M6C phase region, and the same is true of Mo3Ni3C and Mo4Ni2C. THE n carbide structure type has been known since it was determined by westgren' in 1933, yet reliable information on phase compositions of this type is ap-parently scarce. The following selection of suggested formulas illustrates the extent of the confusion con-cerning compositions: W2-3Fe4-3C,1W6Fe6C,2 W2_4Fe4-2C,3 (W,Fe)6C,4 Tj.-W4Co2C and nz-W6Co6C,5 n1-W3Co3C and n2-w4Co2C,5 W3C03C and w6Co3C2,7 MO3Fe3C,8n2-M04Fe2C,9 (MO,Fe)6C,4 MO3CO3C,8 n2-MO4CO2C.9 Many of these compositions obviously overlap, some disagree in carbon content. The use of the designations 77, and n2 is not consistent. There is uncertainty whether two carbides M6C coexist or whether there is only one M6C with a wide range of substitution of one metal for the other. The existence of M12C seems questionable altogether if one ignores the results of a neutron diffraction study of W6Fe6C supporting that particular metal to carbon ratio.'' More reliable information is available for the iso-typic oxides studied by Nevitt,11 Nevitt, Downey, and orris," and Meussner and carpenter.l3 That n car-bides and oxides are structurally identical, particularly with respect to the location of the metalloid atom, has been demonstrated clearly by Stadelmaier and Meussner14 and also by Parthe, Jeitschko, and sadagopan.15 Therefore the present paper, which attempts to establish the phase boundaries of n defini-tively for three carbon systems, has implications for the whole family of filled Ti2Ni types. EXPERIMENTAL PROCEDURE The samples were prepared in two stages. Pellets weighing 3 g were compacted from powders of the elements and presintered in a closed tube of fused silica that had been evacuated to lO-4 mm Hg. This was fol- lowed by arc melting the sintered samples under argon. Remelting the button once was sufficient to produce homogeneous specimens. The metal powders had the following minimum purities in wt pct: molybdenum 99.5, iron 99.0, cobalt 99.7, nickel 99.9, graphite 99.94. Carbon determinations by the gas volumetric method were obtained from thirty-one of the one hundred samples in the annealed condition. They were limited to compositions that were critical to placing a boundary line in the isothermal sections. The carbon losses were comparatively low and averaged less than 1.5 at. pct. For annealing, the samples were sealed in tubes of fused silica evacuated to 10-4 mm Hg. The annealing schedule was 20 hr at 1250°C followed by 150 hr at 1000" ±10°C. For the water quench the silica glass tubes were broken mechanically to speed the quench. The specimens were examined in the as-cast and annealed condition by standard metallographic techniques. Some of the as-cast and all annealed samples were studied by X-ray diffraction using a 114.6-mm powder camera with filtered Co radiation. The lattice parameters of the n phases were determined by graphic extrapolation to 8 = 90 deg on a plot against sin2 8. It is estimated that the maximum error in the lattice parameters is ±0.002A.. The phase fields were determined by the disappearing phase method, relying on X-rays for phase identification and on microscopy to detect small amounts of a phase. RESULTS Pertinent information on the binary side diagrams has been summarized by Hansen and Anderko16 and Elliott17 and will not be discussed further. Photomicrographs documenting the equilibria at 1000°C have been selected to avoid redundancy due to the similarity of the three systems. Thus there will be only one picture showing an equilibrium with Mo2C, and so forth. Molybdenum-Iron-Carbon. An isothermal section of most of the Mo-Fe-C system at 1000°C is shown in Fig. 1. No attempt has been made to distinguish between a and y iron or to determine their phase boundaries. A conspicuous absence is the phase Fe2 1Mo2C6 with the Cr23C6 structure, supporting the suggestion by Krainer4 that it decomposes by annealing at high temperatures. The only ternary phase is found in a narrow range around Mo3Fe3C (MO43Fe43C14). A microstructure with a two-phase mixture of Mo + n is seen in Fig. 2. The variation of the lattice parameter of n with the estimated composition is shown in in Table IA. The phase diagram does not agree with the results of Kuo9 who reported n2-Mo4Fe2C. Our lattice parameter Varies from 11.095A at the iron-rich end to 11.140Å at the molybdenum-richoend of the phase field whereas Kuo9reported 11.26Å for Mo4Fe2C. We are in agreement with the older work

Jan 1, 1970

Jan 1, 1925

By R. G. Aspden

The cold rolling and annealing textures were studied for 3 pct Si-Fe grains initially (001) [hkl]. A concentration of (001) [loo] primaries were observed only in the annealing textures of crystals initially having [loo] within 8 deg of the rolling direction. Eke annealing textures of the (001) [I101 cold rolling textures were sensitive to the initial orientation of the grains. Single crystal data were used to explain the formation of (001) [loo] in poly-crystalline malerial. CUBE texture formation in 3 pet Si-Fe sheet occurs during the final high temperature anneal. Its formation is dependent on the proper distribution of (001) plane primaries with reference to the rolling direction&apos; and on the growth of these primaries by secondary recrystallization. The selective driving force for these primaries with (001) within 7 deg of rolling plane is derived from the difference in surface energy between the annealing atmosphere and the crystallographic planes exposed at the surface of the sheet.&apos;-= The alignment of [loo] directions of (001) secondaries with the rolling direction is required for optimum magnetic characteristics7 and is dependent on processing.&apos; A high degree of alignment has been observed when the final cold rolled texture has a strong (111) [ll2] type component3 and the normal grain growth texture prior to secondary recrystallization has components with a [loo] parallel to the rolling direction and planes from (001) to (110) parallel to the rolling plane.1,3,8,9 Generally, this (001) component is much weaker than the (110) component. The growth rate of (001) plane primaries to secondaries has been found to be independent of the orientation of the primaries with reference to the rolling direction, i.e., the secondaries have the same degree of alignment of [loo] directions with the rolling direction as the (001) primaries.&apos; Hence, the rolling and annealing textures of individual grains or single crystals are of interest in understanding the development of the (001) [loo] secondary recrystallization texture. (001) components have been observed in the annealing textures of cold rolled grains initially having a [loo] parallel to the rolling direction and an (001) rotated up to 30 deg from the rolling plane. Crystals initially near the (001) [loo] orientation when rolled under the influence of constraints imposed by neighboring grains form deformation bands and ro- tate in both directions toward (001) <110>.10,11 Deformation bands have been reported also for crystals initially with an (001) within 1 deg of the rolling plane and a [loo] within 1 deg of the rolling direction when rolled as a free single crystal.12 These crystals have weak recrystallization textures and contain near an (001) [loo] component.10-12 When near (001) [loo] crystals are rolled as free single crystals no deformation bands form and the crystals rotate by a single rotation toward (001) [110]. Recrystallization after a 70 pct cold reduction yielded near an (001) [loo] component13 and after a 90 pct cold reduction an (001) [I201 component." Crystals initially near (210) [001] had a texture after a reduction of 70 and 84 pct which was similar to the (111) [li2] but rotated 10 to 15 deg in the transverse direction. These crystals recrystallize to (210) [OOl] or (410) [001] and contain an (001) [loo] component.10,13 An (001) component has not been detected in the normal grain growth textures of other single crystals. Crystals initially having orientations between (110) [001] and (111) [ll2] have a cold rolled texture of principally (111) [ll2] .10>16 Other crystals with a [I101 parallel to the cross direction rotate to (111) [112] and/or (001) [110] stable end orientations. Crystals initially having from (001) [110] to (111) [lie] retain this orientation after cold rolling.15 The cold rolled textures having [I101 directions parallel to the rolling direction had components in the annealing textures related to the deformation textures by 25 to 30 deg rotations about common (1 10) poles. Cold rolled textures of the (111) (112) type recrys-tallized to (120) [001] or (110) [00l]. The purpose of the present work was to further the understanding of the alignment of [loo] directions of (001) secondaries with the rolling direction. The cold rolling and annealing textures of grains initially (001) [hkl] were studied. These data were applied to the formation of (001) [loo] by secondary recrystallization. PROCEDURES AND EXPERIMENTAL TECHNIQUES The (001) poles near the sheet normal and rolling direction are given in Fig. 1 for the 10 grains studied. Each of these grains was located in the center of a polycrystalline specimen approximately 25 mm wide and 50 mm long. The lower case lettered grains, a through dl were about 1.2 mm in diam and near the (001) [loo] orientation. Specimens containing these grains were from a commercial 3 pct Si-Fe alloy with the principle orientation of (110) [001] as obtained by impurity inhibition of growth with manganese sulfide inclusions.17,18 Upper case lettered grains, A through F, were about 6 mm in diam and had (001) planes near the rolling plane and [hkl] di-

Jan 1, 1963