Search Documents

By C. E. Sims, G. A. Moore, D. W. Williams

During the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging, The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary ab- normal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders' Society of America has, since Nov. I, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. In order that these investigations might proceed on a quantitative basis, hydrogen analyses of a precision considerably higher than any previously reported in the literature were necessary. 'The method chosen was selected entirely on the basis that it had the highest probability of freedom from uncontrollable errors and will be described in detail in another publication.' Briefly, the method used consisted of the hot extraction of solid pieces of steel weighing from 45 to 50 g in a highly evacuated quartz tube maintained at 1050°C (1925°F) for a period of approximately 40 hr. The greatest precautions were taken to eliminate blanks and insure a sound gas-collection system. vacuum and temperature conditions were maintained automatically. Mercury-filled risers were used for the introduction of samples in order that the System could be degassed thoroughly in

Jan 1, 1949

By AIME AIME

ALTHOUGH the present economic depression is felt in the petroleum industry, probably as much as in any other branch of American industry, the Petroleum Section of the Institute was well represented at the general sessions on Monday and at all of the seven division sessions on Tuesday, Wednesday and Thursday. The seven sessions of the Division were so arranged as not to conflict and thus permitted members to hear the programs of all sessions.* The first meeting of the Petroleum Division was held on Tuesday afternoon; a joint session on engineering research and production engineering. The following papers were presented:

Jan 1, 1931

By Phillip B. Bucky, R. S. Taborelli

The term "longwall mining" is best known to coal men, although modifications of the method are continually being used in other fields. Longwall mining is of interest today because it makes for greater inechanization and better supervision at the working face, and therefore lower production costs and increased safety. It is an approach to the factory system of production, the high efficiency of which as compared to that in mines is well known. There is available an accumulation of experience regarding this work but coordination of experience is lacking and this series of experiments was undertaken to help serve this purpose. Model experiments were used for reasons of safety, cost and time, and because it has been previously shown1,2,3 that a scalar inodel built of the same material as the prototype will behave in a manner similar to that of the prototype, with time effects the same, if the effective weight of the model is increased in the same proportion as its linear dimenbions are decreased. This is accomplished by substituting a centrifugal for the gravitational field; i.e., placing the model in a centrifuge and controlling the strength of the centrifugal field by varying the rate of rotation. Many factors affect the behavior of the geologic material overlying a bed, therefore results and conclusions contained in this paper apply only to the conditions presented herein. Longwall Mining What Is Longwall Mining?—Agreement should be reached as to what constitutes longwall mining and therefore what constitutes a longwall face. Let longwall mining be defined as the mining procedure in which the roof and overlying bed breaks tend to parallel the working face. In the ordinary stope or room-and-pillar mining the roof breaks tend to

Jan 1, 1938

By Phillip B. Bucky, R. S. Taborelli

The term "longwall mining" is best known to coal men, although modifications of the method are continually being used in other fields. Longwall mining is of interest today because it makes for greater inechanization and better supervision at the working face, and therefore lower production costs and increased safety. It is an approach to the factory system of production, the high efficiency of which as compared to that in mines is well known. There is available an accumulation of experience regarding this work but coordination of experience is lacking and this series of experiments was undertaken to help serve this purpose. Model experiments were used for reasons of safety, cost and time, and because it has been previously shown1,2,3 that a scalar inodel built of the same material as the prototype will behave in a manner similar to that of the prototype, with time effects the same, if the effective weight of the model is increased in the same proportion as its linear dimenbions are decreased. This is accomplished by substituting a centrifugal for the gravitational field; i.e., placing the model in a centrifuge and controlling the strength of the centrifugal field by varying the rate of rotation. Many factors affect the behavior of the geologic material overlying a bed, therefore results and conclusions contained in this paper apply only to the conditions presented herein. Longwall Mining What Is Longwall Mining?—Agreement should be reached as to what constitutes longwall mining and therefore what constitutes a longwall face. Let longwall mining be defined as the mining procedure in which the roof and overlying bed breaks tend to parallel the working face. In the ordinary stope or room-and-pillar mining the roof breaks tend to

Jan 1, 1938

By Carls Benedicks

It is well known by every one who has had to deal with boiler tubes that these are often seriously affected by a sort of corrosion, occurring as a local pitting, that frequently causes a perforation of the tube in a rather short time. The characteristic appearance of this corrosion is shown in Fig. 1. A very similar corrosion occurs in condenser tubes (Fig. 2).l A study of the microstructure or local chemical composition of the metal (iron 70:30 brass) fails to reveal any cause for this pitting. Of course one might possibly assume the starting point to be some oxide particle, causing an electrolytic local action, but this in no way explains the continued corrosion, progressing even when the assumed oxide particle must have disappeared. By the excellent work done by the Corrosion Research Committee of the Institute of Metals, and communicated, in October, 1923, to the Institution of Engineers and Shipbuilders in Newcastle-on-tyne, stress was laid on the faot that a content of entangled air has a very obnoxious effect. In the following correspondence, Sir George Goodwin stated that "engineers have, for a long time past, regarded air as the big enemy to be fought against in all questions of corrosion'72 and Kenneth Fraser pointed out that the most vital point is "the avoidance or removal of possibly the chief cause of present day corrosion, i. e. entrapped air and gases brought out of solution."3 In their reply, however, the authors state that they had "never for a moment believed that entangled air was responsible for the beginnings of corrosion, and express the opinion that the gradual liberation of air could not account for localized corro~ion."~ On consulting the many textbooks on corrosion, as that

Jan 1, 1925

By Charles H. Behre

This paper deals with recent geologic studies in the slate belt of Northampton, Lehigh and Berks counties, Pennsylvania. The work was conducted under the auspices of the Pennsylvania Topographic and Geologic Survey. Three years have now been spent in detailed consideration of the economic geology of this region. In the field, particular attention was paid to the bearing of geology on quarry development and property valuation and the object of this paper is to summarize the results from that viewpoint. Excellent studies of a somewhat similar nature have already been carried out by Bowles,' but with the emphasis upon the details of quarrying and fabricating methods, rather than upon the geologic relations. The Northampton-Lehigh-BeRks District Location The region here discussed lies in east-central Pennsylvania and extends southwestward from Delaware River, on the New Jersey line, to the Schuylkill in north-central Berks County. It is an elongated belt occupying the northern sections of the three counties mentioned and lying along the southern edge of Blue Mountain. Its length is about 50 miles and its average width five or six, though in places it attains a maximum of 10 miles. There are no large cities in the region, but about 10 miles south are Reading, Allentown, Bethlehem and Easton. Railroads serving the slate belt are the Delaware, Lackawanna and Western, and the Pennsylvania along the Delaware River, the Lehigh Valley and Central of New Jersey along the Lehigh, and the Pennsylvania and Philadelphia and Reading on the Schuylkill. In addition, two railroads—the Philadelphia and Reading and the Lehigh and New England—cut obliquely through the slate region to reach the more isolated communities. Transportation facilities are thus excellent. The slate deposits of these three counties are conspicuously unified, both economically and geologically. In general type of marketable

Jan 1, 1928

By H. D. Hoskold

DuRing the last few years, various persons have been put forward as originators of some mechanical device for the purpose of finding distances without the use of a chain or other linear measuring-instrument, and among these, the Englishman, Gascoigne, 1639, is prominent as the first in England; while James Watt, 1771, and William Green, 1778, are also included in the list of inventors. It is possible that this useful and important problem occupied the attention of others prior to the date cited, and, consequently, it is difficult to decide what nation first gave birth to the inventor of an instrument for the object under consideration. A very important work appeared, not long since, in Paris, devoted to a history and discussion of some of the older and newest forms of surveying-instruments,* and at page 79 of that work a curious old instrument is exhibited, called Bigonometre, i. e., an instrument for finding distances and solving trigonometrical problems. in surveying. A copy of the diagram of the instrument exhibited in the book referred to is represented in Fig. 1. Having had an occasion to read the French work referred to, I communicated with the author of it, and he was good enough to reply that he found a diagram of this old instrument in a book published in 1597, by Danfrie, existing in the library of the Academy of Sciences, in Paris. Col. Laus-

Jan 1, 1904

The most extensive oil shale development program ever undertaken in the United States has been that carried out by Colony Development Operation at Para- chute Creek in western Colorado. Field development goals were completed this spring, with the remainder of the $24 million joint venture program, primarily engineering, environmental and economic analysis, due to be finished by the end of 1972. Upon completion of the overall program, a decision concerning a commercial venture is expected. This program points up the increasing attention being focused on oil shale as a source of crude oil and energy for the U.S. at a time when the nation's supply of oil produced by conventional methods is far from adequate to meet the demand. The oil shale reserves of the Green River formation in Colorado, Utah and Wyoming are the largest hydrocarbon reservoir. The Piceance basin of Colorado, alone, contains some 80 billion bbl of shale oil recoverable by modern methods in reserves more than 30 ft thick and containing at least 30 gal of oil per ton. The U.S. Geological Survey has estimated that the total shale oil reserves of the Green River formation in the states of Colorado, Utah and Wyoming is more than 600 billion bbl of oil in deposits containing at least 25 gal per ton of shale oil.

Jan 10, 1972

By Pual M. Tyler

BLIZKRIEG tactics in the present war have consumed metals on such a profligate scale that some of the best-laid procurement plans for civilian and military needs of even a year ago seem in retrospect incredibly meager. Conservation of raw materials has reached an all-time climax in Germany, where metals are worth more than human life and throwing away an empty toothpaste tube may be legally punished by death. Even the United States and the British Empire, proud masters of nine tenths of the world?s known mineral reserves and processing plants, are being driven to metals and feverishly expanding production facilities that not long ago were deemed overbuilt. After the war is over and inevitable postwar readjustments are completed, it is reasonable to expect that purchasing power ? or at least the ability to procure the comforts and luxuries of life ? will be distributed among vastly larger population than ever before, accelerating the rising trend in demand for industrial raw materials in ever greater quantity and variety.

Jan 1, 1942

By R. M. Murray

Although blister copper has been produced at the Mount Lyell Mining and Railway Company's works since 1896, it is only during the past five years that electrolytic refining has been undertaken locally, this having been done previously at customs refineries, at first in the United States, and afterwards at Port Kembla, New South Wales. Left to right: smelter building, converter building, blower building (in which converter-generators are housed), tank house and anode dock. Wire-bar furnace building in background at center. Possessing a hydroelectric power plant capable of generating power considerably in excess of the requirements of its mines and works at the time, the company was in a favorable position to undertake its own refining work, provided this advantage was not offset by the high cost of coal, which would have to be imported from the mainland, and provided also that the capital cost of the plant would not be unduly large in regard to the relatively small amount of copper to be treated. A study of these several conditions led to the adoption of a high-density plant using blister-copper anodes and equipped with an electric boiler to provide any

Jan 1, 1934

By C. S. Westerberg, C. P. Heiner

Observation of the clinkering action of coal from the Castle Gate D seam in underfeed stokers over a period of years has given rise to the present investigation of the effect of bony coal on clinkering. Some very costly examples of slagging clinkers in particular cases have been of especial interest to the authors. In such cases coal analyses and ash-softening and fluid temperatures have been found of little value. In general, it was noted that slagging mas accompanied by a somewhat higher ash content of the stoker slack, and the suspicion naturally arose that foreign matter was the troublemaker. One would naturally suspect bony coal and rock impurities because of their occurrence and prevalence within the seam and the relative absence of sulphur or other impurities in the coal mined. The test results given herein indicate that the concentration of the bony coal and rock impurities in the coal determines the clinkering tendencies of the ash during combustion. Castle Gate D Seam Extending from the Utah-Colorado line near Grand Junction, Colo., westward to Greenriver, Utah, and thence in semicircular form north and westward to Castle Gate, and from there southward to Mt. Hilgard in central Utah, is a line of nearly perpendicular cliffs, composed of interbedded massive sandstone and shales, making up the coal-bearing horizon of the Mesaverde formation of Upper Cretaceous age. The cliffs face roughly concentrically toward the south and southeast and the strata, with conformably enclosed coal beds, gently dip away from the face of the cliffs and at right angles to their front line. Back of these cliffs the mountain masses rise to an altitude of from 8000 to 10,ooo ft. above sea level. Stretching away from their foot is a great shale plain, on which the towns are situated and over which the railroad lines and highways run. The Castle Gate mines enter the coal beds at their outcrop; the workings extending within a particular coal bed away from the outcrop and under the mountain mass back from the cliff line (Fig. I). Throughout the Mesaverde formation in the Castle Gate general area, there are from two to five workable coal beds. Usually not all of these are coincidentally of workable size and merchantable quality throughout any given large tract. In the Castle Gate mine area, the base of the Mesaverde horizon and coal measures is marked by a massive, cliffmaking, gray sandstone bed 60 to 80 ft. thick. Locally this is referred to as the "Castle Gate sandstone floor." Frank R. Clark, in U. S. Geol. Survey Bull. 793, designates it as the "Aberdeen sandstone." At Castle Gate the various coal beds are designated by the letters A, B, C, etc., commencing with the lowest bed.

Jan 1, 1942

By C. P. Heiner, C. S. Westerberg

Observation of the clinkering action of coal from the Castle Gate D seam in underfeed stokers over a period of years has given rise to the present investigation of the effect of bony coal on clinkering. Some very costly examples of slagging clinkers in particular cases have been of especial interest to the authors. In such cases coal analyses and ash-softening and fluid temperatures have been found of little value. In general, it was noted that slagging mas accompanied by a somewhat higher ash content of the stoker slack, and the suspicion naturally arose that foreign matter was the troublemaker. One would naturally suspect bony coal and rock impurities because of their occurrence and prevalence within the seam and the relative absence of sulphur or other impurities in the coal mined. The test results given herein indicate that the concentration of the bony coal and rock impurities in the coal determines the clinkering tendencies of the ash during combustion. Castle Gate D Seam Extending from the Utah-Colorado line near Grand Junction, Colo., westward to Greenriver, Utah, and thence in semicircular form north and westward to Castle Gate, and from there southward to Mt. Hilgard in central Utah, is a line of nearly perpendicular cliffs, composed of interbedded massive sandstone and shales, making up the coal-bearing horizon of the Mesaverde formation of Upper Cretaceous age. The cliffs face roughly concentrically toward the south and southeast and the strata, with conformably enclosed coal beds, gently dip away from the face of the cliffs and at right angles to their front line. Back of these cliffs the mountain masses rise to an altitude of from 8000 to 10,ooo ft. above sea level. Stretching away from their foot is a great shale plain, on which the towns are situated and over which the railroad lines and highways run. The Castle Gate mines enter the coal beds at their outcrop; the workings extending within a particular coal bed away from the outcrop and under the mountain mass back from the cliff line (Fig. I). Throughout the Mesaverde formation in the Castle Gate general area, there are from two to five workable coal beds. Usually not all of these are coincidentally of workable size and merchantable quality throughout any given large tract. In the Castle Gate mine area, the base of the Mesaverde horizon and coal measures is marked by a massive, cliffmaking, gray sandstone bed 60 to 80 ft. thick. Locally this is referred to as the "Castle Gate sandstone floor." Frank R. Clark, in U. S. Geol. Survey Bull. 793, designates it as the "Aberdeen sandstone." At Castle Gate the various coal beds are designated by the letters A, B, C, etc., commencing with the lowest bed.

Jan 1, 1942

By W. G. Jeffery, James F. McDivitt

THE FRAMEWORK Consider where you, the reader, would place the emphasis m your answer to the following questions on mineral supply. Do you think of the mineral resources of developing countries in terms of the contribution which they can make to world mineral supply or in terms of the contribution they can make to development of the country? Do you look upon developing countries as a source of minerals for world industry or as a potential enormous market for minerals? If you are from a developed country it would be surprising I£ you did not emphasize the first alternative in each case, but it is also possible that simply raising the questions will call for some mental adjustments, because usually we do not think in these terms. If you are among the two-thirds of the world's population which comes from developing countries, you might well emphasize the second alternative. And to a growing extent during the reaming decades of the 20th century this is where emphasis must be placed. Increasing amounts of the world's mineral production come from countries which are in the early stages of development. Mineral consumers of the world look to these regions for continuing supplies of material to help meet their ever-growing needs; the producing countries look to mineral exports as one means of stimulating and financing their economic development-this seems a happy and fortuitous relationship. But due to the complexities of world mineral supply, it is a relationship which is fraught with potential confusion and misunderstanding. That this is so is not surprising when one considers that many of the producing countries are new countries which are urgently trying to find the path along which they can move towards development; that the direction of the path is by no means clear because various theories of economic development, as a planned and deliberate process, are relatively recent in origin and none are well understood; and that the very concept of the less developed countries (LDC's) is a relatively new one. To further complicate the situation there has never been a clear under- standing of the full role which minerals play in economic development, either in the case of those countries which are already classed as developed, or in the case of countries which are in the process of development. Before embarking on an investigation of some aspects of the relationship between minerals and developing countries, it seems wise to establish broad terms of reference, which may not be totally valid but which will at least give an initial direction for a journey with no clearly definable goal. First it can be noted that the world has been divided somewhat arbitrarily into a group of countries that are termed developed or advanced and a group of countries which

Jan 1, 1976

By T. E. Scott, R. P. Zerwekh

The charactevistics of the deformatiotz of fcc thorium were examined between 78 and 473 K. Activation energy, actiuation volume, and the temperature dependence of the flow stress were determined and conlpared uith several theories for the rate-controlling mechnnistn of the tempemture-dependent component of the flou~ stress. It was established that the Cottrell-Stokes law does not hold, even approximately, for thorium. Through consideration of the above factors and other parameters, it was concluded that the vandom solute barrier theory proposed by Friedel demonstrates the best agreement with experimental observations of the deformation of thorium below ambient temperature. THORIUM, the first metal in the actinide series of rare-earth elements, is interesting and important from two points of view. In the more practical vein, it is a potential reactor fuel. As such, it is important to know its properties. Of specific interest here are the mechanical properties of thorium. Second, no detailed information concerning the deformation characteristics of the actinide elements has been gathered to date. In view of the interesting physical and chemical properties of these metals, their mechanical behavior might reveal characteristics which could improve our understanding of the mechanisms controlling deformation of the more common metals. For example, it has been shown1 that thorium exhibits a yield point which is greatly enhanced by interstitial solute elements such as carbon. This is not a normal occurrence in fcc metals. The goal of this investigation, therefore, was to characterize the deformation of polycrystalline thorium. MATERIAL AND PROCEDURES Thorium, made by the magnesium intermediate alloy process described by Peterson et al.,2 was rolled and swaged to 0.065-in.-diam wire. The metal analysis is given in Table I. After preparation, the oxygen and nitrogen contents had risen to 308 and 60 ppm, respectively. The 0.065-in.-diam wires were cut into 2-in. lengths and annealed in a vacuum of lo-' Torr at 750°C for 1 hr, producing a grain size of 2735 grains per sq mm. The ends of the 2-in. sections were masked off so that a 1-in. gage length could be electropolished. Specimens were polished at 35 v in a solution of 6 pct perchloric acid in methanol which was maintained at 0°C . The gage diameters after polishing were about 0.0625 in. The tests were run on a screw-driven tensile machine at a constant crosshead speed corresponding to a strain rate of 0.005 min-'. The strain rate was changed rapidly after each 0.01-in. extension between 0.005 min-' and one of three higher strain rates which were selected in order to achieve strain-rate ratios of 5, 10, and 20. Tests were run at several temperatures from 78" to 473°K; most were tested at 423", 300°, 215", and 78°K. EXPERIMENTAL RESULTS Flow Stress vs Strain and Temperature. Typical true stress-true strain curves for thorium are shown in Fig. 1 for several temperatures over the range 473" to 78°K. The curves for 78", 215", 300") and 423°K were obtained from strain-rate change tests using the lower (0.005 min-') or base strain-rate values of stress. Additional tests, using the same base strain rate at different strain-rate ratios, gave curves which virtually superposed on those shown, indicating that strain-rate changes did not materially influence the work-hardening characteristics at the base strain rate. The curves for 273") 373") and 473°K were standard tensile tests at 0.005 min-'. The behavior of the flow stress with temperature is

Jan 1, 1968

By M. P. Tixier, M. Gondouin, G. L. Simard

In the quantitative interpretation of the SP logs, the electrochemical component is generally taken equal to — K log Rm /Rw where K has the theoretical value corresponding to solutions of pure sodium chloride. This method may be misleading when relatively large quantities of salts other than NaCl are present in form-rrtion waters—as is generally the case for low salinities —or in gyp-base muds. In such cases recourse is made in the field to changing the K value or to adding a correction term to the equation on the basis of local experience. An investigation has been made in the laboratory of the influence of HCO3, SO4=, Ca++, and Mg++ on the amplitude of the SP deflection, which included in par-ricular determinations of the activity coefficients of Ca++ and Mg++. The theory, the experimental techniques and a tentative method for applying the results are described. So far, applications to actual field cases where chemical analyses of waters were available have provided an excellent confirmation of the proposed method. The case of the SP in very salty brines is also considered and it is shown that the use of activity data for sodium gives satisfactory results. HISTORICAL In early times of electrical logging, the SP curve was used exclusively as a tool for the location of permeable beds and the definition of their boundaries. Later, with the introduction of methods of quantitative analysis, attention was called to the possibility of deriving from the SP log some information on the formation water resistivity, which constitutes one essential element for the computation of water saturation from log data. The first laboratory experiments' in 1932 had shown that, as a result of electrochemical phenomena arising at the contact of the niud and the formation, the amplitude of the deflection of the SP curve was, at least partly, a function of the salt concentration of interstitial water and accordingly of its resistivity. It was indicated that the amplitude of the electrochemical component of the SP should be equal to K log R1/R2, R1 and R2 being the resistivities of the mud and of the formation water respectively. However, the exact value of the K coefficient was not determined at that time because the surface clay used for a laboratory model was far from an ideal shale membrane. Consequently, the way was not yet open towards quantitative interpretation. In the early forties, Tixier reported2, on the basis of field log observations, the following equation for the case of NaCl solutions, SP = -71 log f1c1/f2c2, c1 and c2 being the concentrations and f1, f2 the mean activity coefficients. The local variations observed in the empirical values of K, chiefly in the Rocky Mountains, led him to advance the opinion that, besides the relative amounts, the nature of the salts present in the solutions had a bearing on the magnitude of the SP. At about the same time Mounce and Rust- ad published laboratory results which emphasized the part played by the shale in the generation of the SP. On the basis of laboratory tests and theoretical considerations, Wyllie in 1948' published the following equation of the electrochemical SP for the case of NaCl solutions, SP= - 71 log (a1)m/(a2)m

Jan 1, 1958

By J. S. Aronofsky

The results of polentiometric model studies and numerical computations are described. The purpose of these studies was to determine the influence of the mobility ratio on flooding efficiencies during water encroachment in petroleum reservoirs, in systems of regular well geometry. The direct line drive well pattern having relative spacing distances of one and one-half to one was investigated for water to oil mobility ratios of 10. 1. and 0.1. The results of these studies indicate that the pattern Sweep efficiency i.; very dependent upon the mobility ratio. INTRODUCTION The almost universal occurrence of water in the immediate neighborhood of oil-hearing sands lends considerable emphasis to the desirability of having a rational analysis of water encroachment into petroleum reservoirs. This problem has 1)become increasingly important with the accelerated use of water injection for secondary recovery operations. The water encroachment problem has been studied from both the theoretical and experimental viewpoints by Muskat.' He has formulated, in a precise manner, differential equations to express flow in a water encroachment system, and rigorous analytical solutions have been developed for the linear, radial, and spherical cases.' However, it becomes exceedingly difficult to solve the encroachment problem rigorously for any general two-dimensional system in which the shape of the two-fluid interface is not immediately evident from the geometry of the system. The difficulty lies in the fart that a rigorous analytical solution requires that the shape of the two-fluid interface be known simultaneously with its instantaneous posititon and with the pressure distribution on both sides of the interface. Although this paper concerns the study of the two-fluid system of oil and water. the methods described in the paper are generally applicable to other systems of incompressible and immiscible fluids in which the displacing fluid sweep-the displaced fluid down to a residual value. In each region it is assumed there is only one mobile fluid and its mobility is constant throughout the region. The Same procedure. with minor alteration, is applicable for gas injection systems provided the assumption can be made that both the displaced and displacing gases can be described by steady state formulas. For the particular two-fluid problem considered in this paper, there is a relative permeability. K, and a viscosity. p. associated with the water zone, and a different permeability and viscosity associated with the oil zone. The K/p (mobility value associated with a particular volume element of the porous medium. at any instant of time. will depend upon whether the element is ahead of. or behind the advancing interface. It is assumed that all volume elements ahead of the interface are characterized by the K/p value for oil, while all the elements behind the interface are characterized by the K/p value for water. That is. the K/p value in the oil zone is constant throughout the oil zone. and the K/p value in the water zone is also constant but different from the value in the oil zone. The symbols are defined at the end of the paper. The well pattern chosen for initial study is the direct line drive; the swept-out area at breakthrough was determined by two different methods which are described in the section on theory. These are: 1. Potentiometric analyzer 2. Numerical computation The use of the potentiometric analyzer for studying water flooding problems is adequately described in the literature, particularly for cases where the mobility in the water zone is assumed equal to the mobility in the oil zone." ' 5

Jan 1, 1952

By J. G. Y. Chow, S. B. McRickard

The tensi1e properties of Ferrovac iron have been studied from 4° to 300°K. The stress required for macroscopic yielding was found to he constant below approximately 50°K. The effect of mechanical twinning on this low -temperature stress plateau was investigated. The onset of twinning occurs in this iron between 130° and 150°K and depending on its previous thermal history the twinning-stress curue may drop below or remain above the vield-stress curves as the temperature is lowered. Twinning has been shown to initiate slip in quenclzed iron at low temperatures. In no instances, however, did the onset of twinning alter the continuity of the yield stress -tempwature curve. Our data shows that carbon inhibits twinning and slip at low tem-peratures. This observation nay be used to explain the ductile-to-brittle transition in iron. The effect of fast neutron irradiation on yielding and embrittlement in iron and Fe-C alloys is offered as supporting evidence for this viewpoint. THE mode of yielding in iron at low temperatures was studied in an attempt to find an expression based on a single mechanism to describe the thermal dependence of the yield stress of iron. There are two types of inflections observed in the variation of the yield stress with temperature in iron and Fe-C alloys. The first is associated with ductile behavior and consists of a region extending 50" to 100°K above absolute zero in which the yield stress is independent of temperature. The second is observed in more brittle materials such as Fe-C alloys and irradiated iron and consists of an abrupt discontinuity in the yield curve as the temperature is lowered through a ductile-to-brittle transition point. The temperature dependence of the yield stress for iron with four grain diameters as found in this study is shown in Fig. 1. To varying degrees all the curves appear to flatten or approach an asymptotic value as the temperature is lowered below 50°K. Several other investigators1,2 have observed a plateau in the yield stress of iron and steel at low temperatures and in 1956 Louat3 presented a theory which contained an explanation for this behavior. In a subsequent exchange with Erickson and Low4'5 who attributed the plateau to the onset of mechanical twinning Louat8 showed that twinning first occurs in iron and steel tested in tension at temperatures as high as 140°K which is well above the observed plateau in yield stress. Furthermore he pointed out that both twinning and slip are basically dislocation processes and that with modified parameters his original theory still applied when deformation is initiated by twinning. Variables which affect the ductile-to-brittle transition in iron are test temperature, strain rate, composition and grain size.7 LOW,8 Hahn et al.,9 and Hull10 have provided evidence which links brittle fracture at a given temperature with the specimen grain size and the onset of twinning. In fact, Hull equates the brittle fracture stress to the twinning stress. On the other hand brittle fracture has been observed in the absence of twinning and priestnerl1 has given a fracture criterion which is valid whether or not fracture is preceded by extensive twinning. The data presented here clarify the role of twinning in the low-temperature deformation of iron. Strong evidence is given that the amount and distribution of interstitial impurities such as carbon are of

Jan 1, 1965

By R. W. Armstrong, P. C. Jindal

WE should like to point out that Hu and cline.1 in their study of the recrystallization of titanium, have obtained data which appear very important for accurately determining the dependence of hardness on grain size for this material. It has been proposed2,3 that the macrohardness. H. of a poly crystalline material should depend on its average grain diameter, l. in accordance with the relationship: H =H0 + kHl-1/2 [1] where Ho and kH are experimental constants. This relationship follows from the hardness dependence on yield stress or flow stress4 and. thence. the Hall-Petch stress-grain size relations.5'6 Fig. 1 shows the Diamond Pyramid Hardness. Dph. values vs the reciprocal square root of the average diameter of the recrystallized grains, taken from the titanium data reported by Hu and Cline. The data in this figure give a linear relationship for the hardness over a wider range of grain diameters than anyone has previously measured. The data are not linear, for example. on an I-1 or l-1/3 scale. At the very large grain sizes the data are in reasonable agreement with measurements earlier reported by Holden, Ogden, and Jaffee.7 For the grain sizes smaller than 1 µ, which correspond in Fig. 1 to hardness values greater than 150, the material was reported as not being completely recrystallized and, therefore, these data appear less meaningful as far as the hardness dependence on grain size is concerned. However. it has been suggested by other investigators that deformed materials exhibit strengthening due to an effective grain size refinement even in the unrecrys-tallized condition.8-10 Also. Hu and Cline have shown that a change in texture occurs for titanium during the recrystallization process and. especially. following it. The influence of this texture change on the hardness-grain size relation would be expected to be less than that reflected in the unidirectional stress-strain behavior, even for an hcp material. because of the actual combined stress system which applies for the hardness test. For, at least, certain combined stresses, average values of the orientation factors should still occur in the stress-grain size analysis of a material exhibiting a preferred orientation.' We previously suggested3 that the experimental constants. H0 and kH. from the Meyer hardness-grain size relation should be correlated with the Hall-Petch constants, uoy and ky.5,6 Our recent study" of the Hall-Petch relation and the hardness-grain size results which obtain for a number of polycrystalline materials shows that: The inequality [2] is explained by noting that the hardness should be correlated. perhaps, with the flow stress at some value of strain, as suggested by Dugdale,12 and. also, that the influence of strain on the Hall-Petch relation is to increase uo and not change k very much." Normally. Dph values and Brinell hardness values are nearly equivalent to each other and to the Meyer hardness number. For the case of titanium, then. the inequality [2] may be evaluated using the experimental values of ao = 8.0 kg per sq mm and ky = 1.3 kg per mm3/2 obtained from the experiment of Guard.6,13 Thus, (Ho/uo) = 12 and (kH/k3) = 1.3. This research has been supported at the University of Maryland through the Center of Materials Research by the Advanced Research Projects Agency of the U.S. Government.

Jan 1, 1969

Jan 1, 1959

By James E. Harding

AT just about the geographical center of the peninsula of Lower California is the El Arco gold mine. It is small and spotty, and three separate attempts to operate it in the past have failed. The only reason the present operation is possible is because of the higher price of gold and because the previous operators had spent about $300,000 developing the property with shafts, four levels, machinery, and a complete mill, all of which was acquired at a bargain price. All the known ore in the mine, to say nothing of the cost of recovering it, is

Jan 1, 1937