Search Documents

By James J. Halbouty, Michel T. Halbouty

Drilling activity in the South Texas area, which includes the South Corpus Christi and Laredo districts, showed a marked decline during 1941 from that of the preceding year. The rate of new discoveries, however, 'compared favorably with exploratory results of 1940 because of the many new productive sands opened in existing fields. South Texas completions for 1941 were about 12.3 per cent below the 1940 figure, compared with an increase of approximately 5.5 per cent in the total number of completions in the United States during 1941 over the 1940 total. During the year, 1452 wells were drilled in this area; of these, 1205 were drilled in or as extensions to the proven fields, and 247 were rank wildcats drilled in search of new producing pools. The comparable 1940 figures were: 1320 field or extension wells and 336 rank wildcats, a total of 1656 completions. This represents a decline in 1941 of approximately 8.7 per cent in proven-area wells, and of about 26.5 per cent in rank wildcats. It must be stressed that wells that were considered rank wildcats at the beginning of operations, but which opened production later classified as additions to existing fields, are not regarded as rank wildcats in this and previous annual reports on this same area. These wells are classified as semiwildcats (Table 2). There were 13 new oil or distillate fields and 4 new gas areas opened during the year, as listed in the next column. This listing represents a decline of 32 per cent from the 25 new areas found during the previous year, and to a great extent can be attributed to the 26.5 per cent decline in wildcatting. The rate of new discoveries based on the 247 wildcats was 14.5 to I, which compares somewhat unfavorably with the 13.4 to I ratio obtained in 1940 (Table 5). Dry wildcats totaled 230. The proof of the prolific character of the South Texas area as a source of petroleum reservoirs is to be found in the fact that of the 1205 field or extension (semiwildcat) wells completed during the past year 61 opened production from new sands or found crude in formerly distillate-producing sands. The 1940 total of 1320 such wells accounted for 50 horizons that provided either new production or crude in distillate sands, and in this respect the 1941 rate of discovery shows to greater advantage, the ratios for new sands being 19.7 to I for 1941 and 26.4 to I for 1940. The 1205 field or semiwildcat wells completed in 1941 resulted in 926 oil or dis-

Jan 1, 1942

By W. H. Hough, P. B. Leavenworth

Development during 1942 led to the discovery of 26 new fields in the Texas Gulf Coast, as compared with 27 during 1941. Of these, 19 are classed as oil fields, 4 distillate fields, and 3 gas fields. Production from the new fields amounted to 614,467 bbl. to October 1942. Producing Sections.—Discoveries in I942, compared with the previous two years, classified by producing formations, are shown in the following table: It is interesting to note the increase in Wilcox discoveries due to the extensive geophysical campaign that has been con. ducted since 1940. Drilling.—During the year 688 wells were drilled, of which 574 produced oil or gas and 114 were dry. This represents a considerable decline in activity over the previous year, when 1405 wells were drilled in the area, of which 1081 were producers and 324 failures. Jackson County continued to hold the lead, with 222 wells completed. Production.—-Despite curtailed drilling, production amounted to 118,009,451 bbl. for 1942, indicating a slight increase over the 113,726,893 bbl. produced during 1941. The statistics in Tables I and 2 include condensate and distillate as oil production, because many Gulf Coast fields produce oils with a wide variation of specific gravities, all of which are commingled in pipe lines. Table 3 shows by counties most of the activities referred to. The number of wells drilled includes only field wells; not wildcats. Outstanding Fields of 1942 The Texas Gulf Coast covered in this report has 270 more or less active oil and gas fields, including the new discoveries of 1942. Of these the most outstanding from the standpoint of production are listed in Table 4. Each of these fields produced one million barrels or more during 1942. Some of the fields where new extensions are occasionally referred to as separate fields, such as West Columbia and New West Columbia, or Thompson and South Thompson, are combined to give a more accurate outline. Two interesting facts may be noted from this list of some 26 oil fields: (I) that the Lolita field, Jackson County, is the only discovery since 1938 to produce more than one million barrels annually, although there have been 79 discoveries since Jan. I, 1940; (2) that 20 of these 26 fields produce from the Frio. New Fields ALief, Harris County.—Pure Oil Company's No. I Mike Albanese was drilled to 8637 ft. in Cook Mountain shale. After numerous tests the well was completed on Apr. 20, 1942, in a Yegua sand at 7919 to 7924 ft. for 54 bbl. of 52' gravity oil and 3,335,000 cu. ft. of gas through

Jan 1, 1943

By W. H. Hough, P. B. Leavenworth

Development during 1942 led to the discovery of 26 new fields in the Texas Gulf Coast, as compared with 27 during 1941. Of these, 19 are classed as oil fields, 4 distillate fields, and 3 gas fields. Production from the new fields amounted to 614,467 bbl. to October 1942. Producing Sections.—Discoveries in I942, compared with the previous two years, classified by producing formations, are shown in the following table: It is interesting to note the increase in Wilcox discoveries due to the extensive geophysical campaign that has been con. ducted since 1940. Drilling.—During the year 688 wells were drilled, of which 574 produced oil or gas and 114 were dry. This represents a considerable decline in activity over the previous year, when 1405 wells were drilled in the area, of which 1081 were producers and 324 failures. Jackson County continued to hold the lead, with 222 wells completed. Production.—-Despite curtailed drilling, production amounted to 118,009,451 bbl. for 1942, indicating a slight increase over the 113,726,893 bbl. produced during 1941. The statistics in Tables I and 2 include condensate and distillate as oil production, because many Gulf Coast fields produce oils with a wide variation of specific gravities, all of which are commingled in pipe lines. Table 3 shows by counties most of the activities referred to. The number of wells drilled includes only field wells; not wildcats. Outstanding Fields of 1942 The Texas Gulf Coast covered in this report has 270 more or less active oil and gas fields, including the new discoveries of 1942. Of these the most outstanding from the standpoint of production are listed in Table 4. Each of these fields produced one million barrels or more during 1942. Some of the fields where new extensions are occasionally referred to as separate fields, such as West Columbia and New West Columbia, or Thompson and South Thompson, are combined to give a more accurate outline. Two interesting facts may be noted from this list of some 26 oil fields: (I) that the Lolita field, Jackson County, is the only discovery since 1938 to produce more than one million barrels annually, although there have been 79 discoveries since Jan. I, 1940; (2) that 20 of these 26 fields produce from the Frio. New Fields ALief, Harris County.—Pure Oil Company's No. I Mike Albanese was drilled to 8637 ft. in Cook Mountain shale. After numerous tests the well was completed on Apr. 20, 1942, in a Yegua sand at 7919 to 7924 ft. for 54 bbl. of 52' gravity oil and 3,335,000 cu. ft. of gas through

Jan 1, 1943

Who's Who in Mineral Engineering 1977 - SME Membership Directory of the Society of Mining Engineers of AIME

Jan 7, 1977

By Marius R. Campbell

VARIOUS classes of coals are recognized in this country at the present time. These classes depend largely upon physical characteristics rather than upon chemical composition, and consequently they cannot be accurately defined. The divisions into anthracite, semi-anthracite and semi-bituminous are fairly satisfactory; but the term bituminous embraces so large a variety of coal that it is of little value, and the term lignite is so loosely applied that it has little or no place in a scientific classification. At present there is no way of accurately defining the vari¬ous classes of coal, because no adequate scheme of classification, which applies to lignites as well as bituminous coal and anthracite bas been proposed. The object of this paper is to present such a scheme, which is based upon data obtained dur¬ing the past year by Prof. N. W. Lord,1 in charge of the chemical laboratory of the United States Geological Survey coal-testing plant at the Louisiana Purchase Exposition, St. Louis. All the classifications of coals proposed prior to 1877 were based either on physical characteristics or on proximate analyses, including all of the impurities. These schemes were illogical and highly unsatisfactory, for the physical properties of a coal give little indication of its true composition; and impurities, such as ash and sulphur, are largely the results of acci-

Sep 1, 1905

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of April, 1913: BARNES, BLAKESLEE, Min. Engr Burrwood, La. BOYLSTON, HERBERT M., Cons. Met. Engr 26 Abbot Bldg., Cambridge, Mass. BUEHLER, HENRY A., State Geol Rolla, Mo. CASTO, WILLIAM H., JR., Mining Bonanza, Idaho. COHEN, MAXWELL B., Mill Operator Miami, Ariz. EVANS, MILTON R., Shop Draftsman 92 Division St., Kingston, Pa. HARPER, WALTER S., Asst. Treas 42 Broadway, New York, N. Y. JAMES. JAMES S.. Min. Engr Telluride. Colo.

Jan 5, 1913

By Claus G. Goetzel

POWDER metallurgy is known as the art of producing metal powders and fabricating them in a nonfusion process by a simultaneous or consecutive application of pressure and heat under controlled operating conditions. Before the advent of powder metallurgy, the high melting points of the refractory metals and nonmetals made their manufacture and use practically impossible. Today, however, the uses of refractory materials in high-speed cutting tools, surgical instruments, brake linings, electrical contact switches, and filaments in incandescent lamps are commonplace in industry. Lately designers have even been turning to powder metallurgists to develop new techniques of fabricating refractory materials for extreme-service use in high-temperature zones of such modern products as gas turbines and jet engines. The new techniques being born will undoubtedly provide industry with a great number of new alloys and materials for future designing.

Jan 1, 1948

By Scott Turner

GOLD AND SILVER, the monetary metals, have presented in the last year a striking contrast; gold has experienced unusual prosperity, while silver has been depressed more severely than ever before. Gold mining has been hailed as the only basic industry that is able to thrive on depression; the new gold produced is thought by many to be the most important material for the reconstruction of prosperity. Silver production, meanwhile, has been sinking to its level of 40 years ago, and its price to a level never before recorded. These factors have reduced the value of silver produced in 1932 to about the value of the average annual production more than a century ago, that of the decade 1801-1810. No other major commodity in world trade appears to have suffered a greater decline during the present depression.

Jan 1, 1933

By R. C. Neavel

One of the most important requirements to be met by any coal producer is delivery of size consists tailored to specific applications. Generally these specifications include a minimum as well as a maximum size limit. The customers of a major Indiana coal producer noticed that some shipments of sized coal contained a large proportion of undersize pieces. Also, in these shipments, the pieces which remained within the specified limits were cracked and, when handled, crumbled readily. The producer, certain that these shipments had been properly sized at the tipple, suspected that degradation had occurred in transit. The Indiana Geological Survey was requested to examine the coal from one of these shipments to attempt to determine the cause of breakage. Two basic facts about coal and coal seams led to the employment of petrographic techniques in this investigation. First, all coal seams consist of accumulations of diverse organic and inorganic constituents; and second, most coal breakage, either desirable or undesirable, can be attributed to the inherent weakness of some of these constituents or to poor adhesion between certain constituents. Analyses of degraded coal Sampling: Samples were secured from 2 stock piles of 2-by 4-inch coal in a dealer's yard. The coal in both piles had received the same treatment from mining to storage, although it had been mined and shipped on two different days. The size consist of one pile, however, appeared smaller than that of the other. The sample from the degraded pile is referred to as the slack sample, and the other is called the unslack sample. Size analyses: In order to determine the actual size consist, the samples were screened, with a minimum of rough handling, on square 2-inch, 1-inch, 1/2-inch, and 12-mesh screens. It is assumed that 100 percent of the 2-by 4-inch coal is retained on a 2-inch round screen at the tipple. Analyses of several loads at the tipple indicate that approximately 26 percent of the 2- by 4-inch coal, 100 percent of which was assumed held on a 2-inch round screen, passed through a 2-inch square screen. Twenty-six percent may be taken as the normal difference between round and square screens. Results of the analyses of stockpile coal are shown in Table 1. Cumulative percent versus size are plotted on a Rosin-Rammler chart as Figure 1. Both samples approximately follow normal size distribution; this indicates that breakage is not size preferential and also that the samples are representative of the stockpiles. Although both samples exhibit the same general size distribution, the median size of the slack sample is considerably smaller than that of the unslack sample. Fifty-five percent of the unslack sample was undersize (29 percent greater than the normal 26 percent difference), and 83 percent of the slack sample was undersize (57 percent greater than the normal 26 percent difference). Both piles contained a greater percentage than normal of undersize coal; this indicates that they were both affected by degradation, but to a different degree. Bedding-plane analyses: Coal, because of its laminated nature, will break preferentially along bedding planes, especially where adjacent constituents are poorly cemented to each other. Subsequent breakage perpendicular to the

Jan 1, 1961

By John R. Eckel

A Iaboratory drilling rig has been devised and placed in operation which permits the application of hydrostatic, terrastatic, and formation pore pressures to a rock sample for drilling under controlled conditions. Calibrated rests of this equipment in-dicate qualitative agreerment with field results on the effect of weight on bit, rotary speed, and rate of circ~~lation on drilling rate. Tests under pressure, using water and air as the drilling fluids, indicate that when drilling saturated limestone samples, a pressure differential between hydrostatic and formation pressure is the only pressure which affects drilling rate. A differential in either direction causes a reduction in rate, but the same diflerential from the wellbore into the formation causes the greater reduction. Also, in lime.stone, air favorably affected drilling rote only when compared to water at high hydrostatic pressurre, all other conditions remaining constant. Large increases in drilling rate with air could be obtained in the laboratory only while drilling a shale, which offered a limited permeability to nitrogen and which could be drilled with a differential from the formation into the wellbore. In general, the magnitude of the changes due to the pressure effect were small compared to changes in drilling rate obtainable by changing either bit weight or rotary speed. INTRODUCTION In the course of Humble's drilling research program, the desirability of investigating several factors which lend themselves to laboratory rather than field study became obvious. Principal reasons for this are the expense involved in field studies and the difficulty of exercising the required degree of control. Of primary importance are investigations of the effect of fluid pressure on rock rate, the effect of pressure on rock drillability, and a study of the fundamental mechanics of rock failure and chip generation. Several years ago some work in the laboratory on the effect of mud properties on drilling rate was re- ported to the API', but the completion of this work and the investigation of the other variables affecting drilling rate required equipment somewhat more elaborate than that used on these earlier tests. This equipment has been assembled to form Humble's Drilling Engineering laboratory. To date only the effect of pressure on rock drillability while using water and air has been investigated, and this work is not yet complete. Facilities are available to investigate the effect of fluid properties on rate of penetration, and information is being assembled on a current basis on the mechanics of drilling. The sequence of presentation in this progress report is somewhat different from that in which the data were obtained since the order of ex-

By H. T. Kennedy, S. G. Dardaganian, J. L. Clanton

This paper presents equilibrium ratios measured on oil and gas samples taken from the Kelly-Snyder field at the reservoir temperature of 128°F. From these data smoothed curves were constructed for the reservoir fluid up to the bubble-point, 1,874 psia. A material balance calculation, based on the use of equilibrium ratios instead of the usual solubility and shrinkage meayr~rements is made on the field and compared to the con\.entional method. DETERMINATION OF EQUILIBRIUM RATIOS The equilibrium ratios, or K values were obtained by recombining separator samples of oil and gas taken when the reservoir was above its bubble point, and thus represented the reservoir fluid before any change had occurred due to the evolution of gas. The well sampled had a gas-oil ratio of 617 cu ft of high pressure sepalator gas per barrel of separator oil. and a bottom-hole temperature of 128°F. Samples were brought to equilibrium by agitating for 24 hours in a thermostat, maintained at the proper temperature within 0.2ºF, mercury being added when necessary to maintain the pressure constant. Samples of oil and gas were then taken by constant pressure displacement, and analyzed by low temperature frac-tionation. Equilibrium ratios were determined at 128°F and 500, 800, 1,000 and 1,400 psig. At the latter pressure, there were indications that the gas samples were contaminated with small quantities of oil, and only data taken at the first three pressures were included in Fig. I. This figure has been extended to higher and lower pressures by the use of the Fluor charts for 3,000 psi convergence pressure, on which the experimental points fit well. MATERIAL BALANCE EQUATIONS The possible errors involved in conventional material balance equations have been analyzed by Muskat1. Where the errors occur in field measurements, or in obtaining effective averages from variables such as gas-oil ratio and pressure, they will evidently be involved in any attempt to estimate the content of the reservoir. On the other hand, substantial errors may be introduced in conventional material balance calculations by: (1) the neglect of the amount of oil dissolved in gas at high pressures and temperatures in the reservoir, but which condenses under separator conditions; (2) the assumption that the separation of oil and gas in the reservoir may be duplicated by a differential liberation in the

By Richard A. Kesler, W. Michael Reed

Grindability or resistance to fine comminution is the fundamental issue involved in the application and sizing of grinding mills. Over the years, many theories for determining the amount of energy required for size reduction to a specified fineness have been proposed. The first published theory, introduced by P. R. von Rittinger in 1867, stated that the energy required for crushing or grinding is proportional to the increase in surface area produced. The surface area of a ton of particles of diameter (d) is proportional to (1/d), therefore the work input per ton for particles of diameter (d) would be proportional to (1/d). The second significant theory is that of F. Kick published in 1885. Kick said that the work required is proportional to the reduction in volume of the particles concerned. If (f) is the diameter of the feed particles and (p) is the diameter of the product particles, the work input relationship would be: [W =Ioq(f/p) 9] The "Third Theory" of F.C. Bond, introduced in 1951, states that the work required is proportional to the length of the new crack tips produced in particle breakage during crushing or grinding and equals work represented by the product minus that represented by the feed. This takes the form: [W=]

Jan 1, 1982

By Felix Edgar Wormser

JUST as the ancients used the products of their crude mining endeavors to fashion tools with which to make digging easier, so today mining enterprises are dependent upon the very metals they mine for the efficient conduct of mining and metallurgical operations. In fact, the outlet afforded by the production of minerals in the United States is no mean market for the nonferrous metals. I believe that mine managers frequently lose sight of the opportunity they have to select from competitive products those which will help the market for their own metal output. For example, some years ago a large lead mine used storage-battery locomotives for its haulage, common practice, of course, throughout the United States. These particular locomotives, however, were powered not with the ordinary lead storage battery but by a competitive battery product made from an imported metal. After studying this situation, the manager saw how he could help himself by purchasing a product made from his own mineral output, and in his next order turned tip the use of the lead storage battery.

Jan 1, 1935

By H. B. Charmbury, D. R. Mitchell

Everyone in the coal industry from top management to the preparation engineer is vitally interterested in recovering as much salable coal as possible from the run-of-mine product. Coal losses from a preparation plant occur in the solid refuse material being discharged from the plant and in the bleed-off slurry from the water circuit. The refuse is generally hauled from the plant in solid form by trucks, conveyors, or aerial trams to the refuse or culm banks or it may be crushed and transported by hydraulic methods to refuse ponds or dams. The loss of coal in refuse material and the extent of this problem has been covered in another paver.' The loss of salable coal in the plant bleed-off slurry is one of the water circuit problems in coal preparation plants. Slurries originate at various places in the processing circuits and are usually disposed of by transportation to waste ponds known as slurry ponds. Even though the combustible material discharged as slurry and refuse from the plant is labeled a loss, the loss must only be considered temporary. There is a tendency at the present time to examine refuse and slurry losses and to reprocess these materials to recover valuable coal. Slurries from eight bituminous coal preparation plants in central and western Pennsylvania have been sampled and examined to determine the amount of recoverable coal in each. Examinations of the samples were made to determine the tons per hour of solids and the gallons per minute of water in the slurry; the size, ash, and sulfur analyses of the solids; and the sink-float characteristics of the larger solids. The extreme fines (—325 mesh material) from one of the samples has been examined further to determine the micron size fractions as well as the ash and sulfur content of the micron sizes. Collection of the Samples: Field trips were made to each of the plants where samples were obtained and discussions held with the preparation engineer prior to sampling. The flowsheet of the plant operation was studied and a time-period selected to obtain a representative sample. At least 20 1-gal samples of total plant bleed-off suspensions were collected at each plant in increments over designated periods belived to be typical of the plant flow Three of the samples were obtained from plants in the Pittsburgh area. Each plant supplied information on the capacity, operating time, type of cleaning equipment used, water and material balances, and auxiliary equipment. From the time required to collect given amounts of slurry and from the amount of solids in the slurry, total solids discharges from the plant were calculated and compared with the plant flow. Ash and sulfur analyses of the total solids were also checked, at some plants, with company figures. In all cases where checks could be made there was reasonable agreement between company figures and those reported here. Analysis of the Slurries: Representative fractions of properly agitated samples were examined in the laboratory to determine the specific gravities of the slurries. The solids and water were separated by filtration to check the weight of each so that the percent of solids in the pulp could be determined. From the resulting data, presented in Table I, it may be seen that the percent solids in the slurries ranges from 2.8 to 39.0 and the amount of solids from 2.61 to 45.61 tph. Size Analysis of Solids: Representative fractions of the slurries were permitted to settle and the clear water was removed by siphoning. The solids were then wet-screened at 28, 35, 48, 65, 100, 150, 200 and 325 mesh. Results of the size analyses are presented in Table 11. These results indicate the extreme variation of sizes and in most cases the degree of fineness of the solids. The amount of —325 mesh ranges from 22.5 to 84.5 pct and the amount of+200 mesh from 8.3 to 69.1 pct.

Jan 1, 1961

By A. T. Miesch, L. B. Riley

Distribution of minor elements in sandstone-type uranium deposits of the Colorado Plateau is being studied by the USGS on behalf of the A EC. A primary objective has been to provide basic data which could be useful in geo-chemical exploration for new deposits. The basic statistical measures — similar to those used in sedimentary petrology—are described. The underlying principle is that the frequency distributions fit or approach the log-normal form. Since 1952 the U. S. Geological Survey on behalf of the U. S. Atomic Energy Commission has conducted a study of the distribution of minor elements in sands tone-type uranium deposits of the Colorado Plateau. A primary objective in this study has been to provide basic data which could be useful in geo-chemical exploration for new deposits. Among the basic data considered important are estimates of the abundance and habit of each element in the ore and in the host rocks. It has been found that a few basic statistical techniques, and variations of these techniques, are useful in this type of study. Some of the basic techniques have been used to advantage by researchers in geochemistry and in other fields of geology, especially sedimentary petrology; others have been used to only a limited extent. Among the latter is the linear correlation coefficient, which has proved useful in assessing the element associations in a particular rock type without analysing individual mineral separates. In computing the basic statistical measures a scale has been used which is, in some ways, similar to the phi ($) scale used by sedimentary petrol-ogists in grain-size studies.' FREQUENCY DISTRIBUTIONS It has been recognized for some time that the results of analyses for a given minor element in a suite of samples of rocks or ores yield frequency distribution curves which are approximately normal when the curves are plotted on logarithmic or geometric scales. In other words, the analytical results give an approximate lognormal frequency distribution. A classical example is given by D. G. Krige2 in the study of the distribution of gold values from a mine on the Witwatersrand. Another example is shown in Fig. 1, the distribution of barium concentrations in samples of uranium ore from the Chinle formation. The geochemical data are analogous to grain-size data gathered by the sedimentary petrologist. Both types of data, after simple logarithmic transformations, may be treated by conventional statistical methods based on the normal distribution. This is not to say that other types of transformations may not serve equally well or better for particular element distributions.3 Spectrographers and other analysts are quite aware of the dependence of their precision on the concentration of the element present.4 For example, in the part per million range the variation may

Jan 1, 1961

By R. W. Drier

THE conductivity of copper wire is of prime importance to the electrical industry and consequently to the copper refiner and wire manufacturer. Annealed copper wire has a higher conductivity than hard-drawn wire, but, on the other hand, its tensile strength is lower. In an attempt to explain the reasons for these changes in property or at least to study the conditions existing in these two types of copper wire, the experiments described here were carried on in the Department of Metallurgy of the Michigan College of Mining and Technology. This is only a partial and preliminary report on some of the work done to date on a research program of which the object is an intensive study of copper. It is offered with the hope that, though it is not an exposition of the most rigorous of conclusions, the general trend of inferences which may be drawn will be of value and interest.

Jan 1, 1929

By TENNEY C. DeSOLLAR

TRADITION tells us that the earliest use of Alabama iron was to make shoes for the horses of General Andrew Jackson and his men during the first part of the nineteenth century. The first recorded incident in the making of iron was the request of U. S. Indian Agent Benjamin Hawkins "that a crew of blacksmiths be sent to the Creek Nation in the lower Mississippi territory." These frontiersmen made up the first body of pioneer iron makers in the territory. The first known blast furnace was built by Joseph Heslip in 1818 at Russellville, named after Major William Russell, who was General Jackson's chief of scouts. The Tannehill furnace was built in 1830 in what is now Tuscaloosa County and its ruins, as shown above, can be seen today.

Jan 1, 1937

[ ]

Jan 1, 1938

By M. Mortada

Nonsteady-state flow of slightly compressible liquids in porous media of non-uniform properties has been the subject of a number of recent studies. Most of these studies considered one-dimensional flow in systems with cylindrical geometry and with the properties of the porous medium varying with radial distance only. A. Houpeurt' studied the problem in its general form by examining the solutions of the differential equation, In Eq. 1, the permeability k and the porosity + are arbitrary functions of radial distance. Houpeurt concluded that, except for special forms of the functions k and the problem is not well suited for mathematical treatment, but lends itself to high-speed digital computation. Carslaw and Jaeger' discussed the solution of Eq. 1 for the case in which the permeability varies as a power of the radial distance. P. Albert3 studied analytically the pseudo steady-state solutions in systems of finite radial extent and non-uniform properties. He also obtained some numerical solutions for nonsteady-state flow using a high-speed computer. William Hurst4 examined the interference pressure drop due to a point sink located in an infinite system consisting of two permeability regions in series. In this case, the permeability changed at a radial distance r from the point sink. INTERFERENCE BETWEEN OIL FIELDS IN A NON-UNIFORM AQUIFER The interference pressure drop for oil fields located in an extensive aquifer of uniform properties is discussed in a number of places in the literature. This work considers the interference pressure drop for oil fields located in a non-uniform extensive aquifer comprising two regions of different properties as shown in Fig. 1. Region I of the aquifer extends from which is the radius of Oil Field A, to ar,,, where a>1. It has permeability k,, porosity +, and effective compressibility c,. Oil Field B is located in Region II which extends from ar, to infinity and has different properties from those of Region I, but the same formation thickness h. Region II has permeability k2, porosity and effective compressibility c2. The choice of this type of aquifer should not imply that it is of frequent occurrence. It is chosen primarily to illustrate the effects of non-uniform aquifer properties on oilfield interference. It is of interest to point out that a non-uniform radial aquifer in which both the permeability and the porosity are inversely proportional to the radial distance can be treated in a manner similar to a linear aquifer of uniform properties. The situation where only the permeability varies as the inverse of the radial distance is also amenable to analytical treatment. Both aquifers behave quite differently from a radial aquifer with uniform properties so far as the water influx and the interference pressure drop are concerned. METHOD OF SOLUTION The expression for the interference pressure drop in Oil Field B due to a constant rate of water influx in Oil Field A is developed in the Appendix. This is accomplished by the simultaneous solution of two partial differential equations describing the pressure in Regions I and 11. The two differential equations are solved subject to the following conditions: (1) at r,, the pressure gradient is constant; (2) at ar the pressure and

By George M. Fowler

EVERY year it becomes more difficult to find new mining districts and new ore deposits. Nearly all of the important discoveries so far can be attributed to surface manifestations overlying the ore deposit. In the future greater skill will be necessary to find ore deposits that give little or no indication of their presence. Mining geology is making progress by broadening its attack upon mineralized regions, by including in its investigations studies of the relation of physical-chemical processes to ore precipitation and various phenomena that heretofore have not always been looked upon as major factors in the problems. Such, for example, are petrographic peculiarities that will help determine structure, aspects of strata or formations favorable or unfavorable to structural deformation or mineralization, and renewed studies of chert and dolomite. This broadening attack is not necessarily being directed to the study of large areas, but rather by doing extremely detailed work in three dimensions in relatively small critical areas to find the key to the structure, reasons for the manner of rock deformation, composition and texture of the rock, and other con¬trolling factors in the larger areas.

Jan 1, 1935