Search Documents

By R. W. Parsons

This discussion concerns fitting an ellipse to angle, where the permeability k is measured for a series of plugs cut from varying angles in the horizontal plane. The conclusions and procedures given by Greenkorn, et al. are in no way affected by these comments, since the degree of anisotropy (ratio of maximum to minimum permeabilities) they found is generally quite close to one (see their Table A-1). However, since large anisotropies may arise, I feel that the comments should be made. Both Marcusl and Scheidegger2 have shown that there are two limiting expressions for the permeability of an unbounded anisotropic media. If the permeability is measured in the direction of the pressure gradient, the result is equivalent to the author's Eq. 11. This is the equation used to find kl1 and k22 from the experimental data. If, however, the permeability is measured in the direction of flow, then the resulting equation for the measured permeability is From these equations it follows that plots on angle will be ellipses. The principal axes will correspond with the major and minor permeability axes. The question arises as to what permeability is actually being measured on an anisotropic sample in the laboratory. An overall pressure gradient and a gross flow rate are determined and a permeability calculated by Darcy's law. The details of the macroscopic flow within the sample will be determined by the boundary conditions of the sample and the orientation and magnitude of the major and minor permeability axes. The situation is shown in Fig. 1 for the two-dimensional case. Using the method of conformal mapping, Marcusl has solved the problem of determining the overall apparent (or measured) permeability for this experiment for any condition of W-L ratios and orientation and magnitude of the principle permeability axes. For W-L ratios approaching zero, the streamlines are all forced by the boundary conditions to be in the direction of the measured permeability which is equal to kg. For W-L ratios approaching infinity, the effects of the no-flow bounds are negligible, and the pressure gradient and measured permeatility direction are parall;l. The streamlines are

Jan 1, 1965

By Nelson W. Taylor

With the extensive deposits of potash minerals which have been discovered in the southwestern states, and their rapid development, a permanent American supply of potassium compounds is now assured. The 325-year history of the potash industry in this country has been told by H. I. Smith1, of the U.S. Geological Survey, and the more recent activities of the Survey and of American potash companies were described last year by the same author2. In fact, it may be stated that so great is the productive capacity that two mines in New Mexico and one in California are able to supply more than half a million tons of crude and refined salts over and above that produced for agricultural purposes. The era of scarcity has given way to an era of superabundance. This situatiori makes it desirable for the potash producer to look for other applications for his product, and it is with this in mind that the writer presents some information pertaining to present and possible future uses for potassium compounds in the ceramic industry. Ceramic Products Ceramic products are essentially solid materials containing one or more oxides such as SiO2, Al2O3, CaO, MgO, FeO, K2O, Na2O, TiO2, which are the oxides of greatest abundance in the earth's crust. The typical ceramic process is that of firing or burning the batch, and the product may be glassy, crystalline or mixed. In the glassy or vitreous group come glass, porcelain enamel and glazes; in the crystalline group, refractory materials such as silica brick, or chromite or magnesia; and in the mixed group, porcelain, chinaware, stoneware, tile, brick, etc., which contain both a vitreous and a crystalline phase, in variable proportions. The ceramic industry of the United States is a billion dollar industry, and is important not only because of its magnitude but also because of the key position occupied by certain ceramic products in the whole manufacturing structure. From the standpoint of use of potash, the field of refractories is of no great interest, since K2O lowers the melting point of a refractory oxide and

Jan 1, 1938

By Nelson W. Taylor

With the extensive deposits of potash minerals which have been discovered in the southwestern states, and their rapid development, a permanent American supply of potassium compounds is now assured. The 325-year history of the potash industry in this country has been told by H. I. Smith1, of the U.S. Geological Survey, and the more recent activities of the Survey and of American potash companies were described last year by the same author2. In fact, it may be stated that so great is the productive capacity that two mines in New Mexico and one in California are able to supply more than half a million tons of crude and refined salts over and above that produced for agricultural purposes. The era of scarcity has given way to an era of superabundance. This situatiori makes it desirable for the potash producer to look for other applications for his product, and it is with this in mind that the writer presents some information pertaining to present and possible future uses for potassium compounds in the ceramic industry. Ceramic Products Ceramic products are essentially solid materials containing one or more oxides such as SiO2, Al2O3, CaO, MgO, FeO, K2O, Na2O, TiO2, which are the oxides of greatest abundance in the earth's crust. The typical ceramic process is that of firing or burning the batch, and the product may be glassy, crystalline or mixed. In the glassy or vitreous group come glass, porcelain enamel and glazes; in the crystalline group, refractory materials such as silica brick, or chromite or magnesia; and in the mixed group, porcelain, chinaware, stoneware, tile, brick, etc., which contain both a vitreous and a crystalline phase, in variable proportions. The ceramic industry of the United States is a billion dollar industry, and is important not only because of its magnitude but also because of the key position occupied by certain ceramic products in the whole manufacturing structure. From the standpoint of use of potash, the field of refractories is of no great interest, since K2O lowers the melting point of a refractory oxide and

Jan 1, 1938

By R. Moldenke

The presence of nickel-chromium in pig iron made fro111 Cuban oles is so well known that the word "Mayari" is unconsciously associated with it. Since 1904, when exploration of the Mayari deposits of iron ore in northeastern Cuba was undertaken, there llas been increasing interest in these ores. Tlie Transactions contain numerous references to t1ieln.l This iron ore, which is shipped to the Tinited States in the nodulizecl state, has been thoroughly tested and found very valuable; the deposit covers over 25,000 acres and there is in sight over 500,000,000 tons of ore that, by systematic mining, runs practically constant in composition. With nickel and chromium present, also titanium in sufficient quantities to attract attention, as well as extremely low phosphorus and sulfur contents, the iron founder is naturally interested in the utilization of RInpari ore for pig iron for the better grades of finishrtl iron products. The present point of coilsn~iil)tion ol ILlapri ore is at Sparrow's Poi111, where hlayari pig iron of ally desiretl coml>osition is made. The composition of the dried ore is about as follows: Iron -29 per cent., silica 3 pc.r cent., nickel 1 per cciit., chroiniun~ 1.5 per cent., alumina 11 per cent., ant1 coinbined water 13 per cent. When nodulized, the iron runs up to nearly 56 per cent., the silic:~, :tlumi~i:i, nickel, and c~llromiurn are slightly highr than the arno~l~its just given. Practically all the, combined wntcr is driven off aild the iiodulizccl ore carries only a few- tenths per cent. of 1 C. M. Weld: Residual Rrolvn Iron Ores of Cuba. Tmns, (1909) 40, 299. C. K. Leitll nnd If'. J. Mcncl: Origin of Iron Ores of Central and Northeostr~n rlbn. Trans (1911) 42, 00. C. W. Hayes: May:~ri and Mos Iron-ore Deposits in Cuba. Idem, 109. J. E. Little: Maynri lron Mincs, as Developed by the Spanish-American Iron ('0. Idem, 152. J. F. Iie~np: M'ryari Iron-ore Dcposi(s. Trans. (1915) 61, 3. C. K. Leith 2nd N. J. Mead: Additional Data on Origin of Lateritic Iron 01cs or Eastern Cubn. Tmns. (1916) 63, 75.

Jan 1, 1923

By R. Moldenke

The presence of nickel-chromium in pig iron made fro111 Cuban oles is so well known that the word "Mayari" is unconsciously associated with it. Since 1904, when exploration of the Mayari deposits of iron ore in northeastern Cuba was undertaken, there llas been increasing interest in these ores. Tlie Transactions contain numerous references to t1ieln.l This iron ore, which is shipped to the Tinited States in the nodulizecl state, has been thoroughly tested and found very valuable; the deposit covers over 25,000 acres and there is in sight over 500,000,000 tons of ore that, by systematic mining, runs practically constant in composition. With nickel and chromium present, also titanium in sufficient quantities to attract attention, as well as extremely low phosphorus and sulfur contents, the iron founder is naturally interested in the utilization of RInpari ore for pig iron for the better grades of finishrtl iron products. The present point of coilsn~iil)tion ol ILlapri ore is at Sparrow's Poi111, where hlayari pig iron of ally desiretl coml>osition is made. The composition of the dried ore is about as follows: Iron -29 per cent., silica 3 pc.r cent., nickel 1 per cciit., chroiniun~ 1.5 per cent., alumina 11 per cent., ant1 coinbined water 13 per cent. When nodulized, the iron runs up to nearly 56 per cent., the silic:~, :tlumi~i:i, nickel, and c~llromiurn are slightly highr than the arno~l~its just given. Practically all the, combined wntcr is driven off aild the iiodulizccl ore carries only a few- tenths per cent. of 1 C. M. Weld: Residual Rrolvn Iron Ores of Cuba. Tmns, (1909) 40, 299. C. K. Leitll nnd If'. J. Mcncl: Origin of Iron Ores of Central and Northeostr~n rlbn. Trans (1911) 42, 00. C. W. Hayes: May:~ri and Mos Iron-ore Deposits in Cuba. Idem, 109. J. E. Little: Maynri lron Mincs, as Developed by the Spanish-American Iron ('0. Idem, 152. J. F. Iie~np: M'ryari Iron-ore Dcposi(s. Trans. (1915) 61, 3. C. K. Leith 2nd N. J. Mead: Additional Data on Origin of Lateritic Iron 01cs or Eastern Cubn. Tmns. (1916) 63, 75.

Jan 1, 1923

By H. H. Rachford, and J. D. Rice

The effectiveness of digital computing machines in making technical calculations depends on how well the work is arranged to utilize the capability of the machines. This note presents a particularly useful way of calculating hydrocarbon vapor-li.quid equilibrium in the flash vaporization (or condensation) system. The method is well suited to sequence-controlled computing equipment. It is not limited to equilibrium calculations and may be used for solution of most implicit equations in one variable. INTRODUCTION There is increasing interest in the use of electronic digital computers in research and engineering calculations. This is a fortunate and inevitable trend in view of both the increasingly extensive numerical work which is becoming a routine part of many daily production operations and growing demand for the overwhelming amounts of calculations required by newly developed numerical methods for solving heretofore unsolved problems. Machines are in many ways ideally suited to the task but of necessity present certain difficulties. for a particular poblem to be solved must often be formulated quite differently from the way it would be arranged for manual solution. This is done in order to take advantage of the inherent speed and precision of electronic computers and at the same time to limit the need for number storage to the capacity of the machine. Therefore, this note is submitted to present a general and quite powerful method of finding solutions of the frequently encountered implicit equation: F(x,y1,y2,...ya)=0.......(1) where the root, x, is to be found for a given set of y1, ... yn.. The procedure is well suited for use with computing machines, for it usually requires but little storage or programming beyond that necessary to evaluate F. HYDROCARBON EQUILIBRIUM The method is described in terms of the problem it was designed to solve, i.e., the calculation of hydrocarbon vapor-liquid equilibrium in flash vaporization. Given the composition of a hydrocarbon mixture and appropriate values of the equilibrium ratios K, to find the phase ratio and compositions in a closed system: let z, be the mol fraction of the i-th component in the mixture. If K, is the ratio yl/xl, where y, and x,

Jan 1, 1952

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1938 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. TECHNICAL PUBLICATIONS in Classes A-Metal A-Lining, B-Milling and Concen-tration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Technical Publications in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. TECHNICAL PUBLICATIONS ill Class G-Petroleum Division are distributed in PETRO-LEUM TECHNOLOGY, which is issued quarterly. TECHNICAL PUBLICATIONS in Classes F-Coal Division, .l-Mineral Industry Education Division, K-Mining Administra-tion, and L-Geophysical Methods of Exploration are issued as separate pamphlets. All Institute member is entitled to one copy of any TECHNICAL PUBLICATION or CON-TRIBUTION. Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute according to their registration by classes. CONTRIBUTIONS and other TECHNICAL PUBLICATIONS will he sent upon request. A member may purchase an additional copy of a TECHNICAL PUBLICATION or a CONTRIBUTION at one cent. a page; in minimum charge, 256. If the TECHNICAL PUBLICATION has been published in METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY, the number of either magazine containing it will be supplied at the sae cent a page (minimum charge, 25¢) rate for the particular TECHNICAL PUBLICATION requested. Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION Of the F, J, K, or L classes at the same rate, butt the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1. TECHNICAL PUBLICATIONS (Separate pamphlet form), $2 per annum; Canadian and foreign postage 50 cents extra. METALS TECHNOLOGY, $7 per annum; Canadian and foreign postage 50 cents extra (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers). MINING TECHNOLOGY, $6 per annum; Canadian and foreign postage 50 cents extra (metal mining, milling and concentration, Industrial Minerals Division, and mining geology papers). PETROLEUM TECHNOLOGY, $4 per annum; Canadian and foreign postage 50 cents extra.

Jan 1, 1938

By A. S. Nowick, E. S. Machlin

ONE of the main criteria used to rate the heat-resisting properties of alloys is stress rupture.1 During a stress-rupture test a tensile specimen is held under a constant load at a constant temperature until it fractures. The chief measurement made during this test is the time required for rupture at the specific test stress and temperature. It was found empirically from a series of stress-rupture tests at a constant temperature that when the logarithm of the time for rupture is plotted against the logarithm of stress a straight line is obtained within experimental error.2~3 This method of showing stress-rupture data has been adopted by many investigators and the KACA.4 By interpolation and extrapolation from these plots, values of the stresses required to rupture the specimens (the rupture strengths) in 10, 100, and 1000 hr are obtained for specific temperatures. Alloys are then rated for a particular application on the basis of their rupture strengths at the rupture life that most nearly represents the application. Inasmuch as stress rupture is an important criterion in rating heat-resisting alloys, it would be advantageous to know the quantitative dependence of the time for rupture on stress, temperature, com- position, and structure. In order to obtain this information, an investigation was made at the KACA Cleveland laboratory during the spring of 1945. The theory of rate processes was used because it has been found to apply to certain processes such as chemical reactions, viscous flow, and creep that occur at a definite rate for given conditions. It was thought that stress rupture was such a process. An equation was derived that gives, for a given com- position and structure, the dependence of the time for rupture on stress and temperature. The investigation is part of a general program to provide information that will lead ultimately to the development of better alloys in order that the efficiency and power output of gas turbines used in aircraft propulsion can be increased. THEORY The theory of rate processes will first be discussed as a general theory. It will then be shown that if stress rupture of heat-resisting alloys can be treated as a rate process, certain equations must be satisfied. Later sections will then show that these equations are satisfied. General Theory of Rate Processes The theory of rate processes5 eveloped by Eyring and others has been applied to chemical reactions as well as to other processes such as viscosity of liquids and diffusion. In every case in which rate- process theory can be applied, there is a small subdivision, so that the macroscopic process is the net effect of all the small processes. This smallest subdivision is called the "unit process.'' For example, in a chemical reaction the unit process is

Jan 1, 1947

ON Oct. 5, 1926, the day before the general ses-sions of the fall meeting of the American Insti-tute of Mining and Metallurgical Engineers at Pittsburgh, a round table conference on the combus-tibility and testing of coke was held at the Bureau of Mines Experiment Station. There were about fifty present, with A. C. Fieldner, chief chemist of the Bureau of Mines, as chairman. The following organi-zations were represented: American Institute of Min-ing and Metallurgical Engineers, American Society for Testing Materials, American Gas Association, Eastern States Blast Furnace and Coke Oven Association, Gas and Fuel Division of, American Chemical Society, and Southern Ohio Pig Iron and Coke Association. In opening the proceedings, Mr. Fieldner explained that the meeting had been called at the suggestion of several members of the Institute and members of other organizations. The subject is of interest to the pro-ducer and the user of coke whether it be in a blast furnace, cupola furnace, house-heating furnace, open grate, gas producer, or in a water-gas generator. There has been much confusion on this subject largely because there is no common definition of combustibility. Does the blast-furnace superintendent, the coke-oven operator, and the fuel engineer have the same under-standing of the term "combustibility"? If a common understanding can be reached, many differences of opinion will disappear. COMBUSTIBILITY OF COKE R. H. Sweetser of Columbus, Ohio, disagreed with the statement of P. H. Royster, T. L. Joseph, and S. P. Kinney in Reports of Investigations, Serial No. 2524, of the Bureau of Mines, in which it was stated that the coke-oven op-erator cannot change coke combustibility by modifying oven practice. Mr. Sweetser held that the coke-oven man can change the combustibility of coke. Blast-furnace men know that coke that will burn easily with low pressure and will. come down in the regular way in the furnace can be pro-duced from a given mixture of coal. His idea of the combustibility of coke is the rate of flow through the com-bustion zone of the blast furnace. If the coke does not pass through in normal manner it is highly incombustible. H. J. Rose of the Koppers Co., Pittsburgh, objected to being pinned down so closely on this phase of the com-bustibility and incombustibility of coke. Coke-oven men are frequently obliged to change oven conditions to make a coke which gives blast-furnace men what they want. The size of the coke and the screening have an important bear-ing on combustibility, and there are many cases on record where by simply changing the different sizes of the coke, everything worked smoothly, and that is a much more combustible coke.

Jan 1, 1927

By H. C. Johnson, J. K. Elliott

One of the primary requirements for successful operation of an enriched gas-drive project is to control the composition of injection gas. This can become a serious and difficult problem, particularly in cases where the enrichment material is being furnished from a number of field -produced gas streams. It is possible to effect control of the injection gas composition through frequent or continuous sampling; however, this can be extremely costly and, in many cases, impractical due to laboratory requirements of time. Another alternative would be to provide a calculation technique which would be flexible and sufficiently accurate to predict composition of the liquid and gas streams of interest at any point in the system. The purpose of this paper is to discuss a technique that was used successfully on an operating enriched gas-drive project for developing information which could be used for controlling composition of the injected gas. FIELD OPERATIONS The particular field (hereafter called Example field) in the example operation being discussed is composed of four oil reservoirs (A. B, C and E) and one gas condensate reservoir (D). Casinghead gas from the oil reservoirs and gas from the gas condensate reservoir are gathered through a field gathering system as shown in Fig. I for injection into Reservoir C. The gas mixture which is recovered from the five reservoirs for injection purposes is composed of gases liberated in 19 individual separators, each operating at a separate temperature and pressure. PROPOSED CALCULATION TECHNIQUE It is well known that vapor-liquid equilibrium calculations in general use throughout the petroleum industry can be used to predict reliably the phase behavior of hydrocarbon mixtures, particularly at pressures less than 1,000 psig. It is then a simple matter to account for the material on a ComPonent basis by m''ing flash and material balance calculations at each separation point in a hydrocarbon system. Accordingly, it was proposed to use vapor-liquid equilibrium and material balance cal- culations with a medium-sized electronic digital computer as a basis for developing a control procedure for use in controlling injection gas composition in the enriched gas-drive project. Although the approach is a simple one, the numerous vapor-liquid equilibrium calculations involved make the problem laborious; in this particular case, it would have been impractical to make sutficiently complete analysis without the aid of digital computing equipment. SAMPLING AND VERIFICATION OF CALCULATION PROCEDURE To obtain representative gas and liquid stream samples and to provide a quantitative measure of overall system Performance for comDarative purpLses, a thorough test of the field and plant system was conducted in the summer of 1957. Oil production at each battery was sta-

By M. T. Halbouty

The Laredo oil district, South Texas, includes an area of approximately 200 miles long north and south and 75 miles wide, embracing the following counties: Starr, Zapata, Jim Hogg, Webb, Duval and McMullen. The area is relatively old in respect to the production of oil, as the first oil was discovered and produced in the Piedra Pintas field in Duval County on Sept. 10, 1905. Since that date, continuous new discoveries have contributed to the development of this district until, at the present time, it is one of the important oil-producing and gas-producing areas in the world. The year 1937 also had its share of new discoveries in the district, including not only new oil fields but also new sands in already producing pools and important extensions to existing sands and fields. Among the most important field discoveries, by counties, are: Duval County..... Benavides, Sweden, Thomas-Lockhart, Labbe and Lundell fields Jim Hogg County.. Las Animas field McMullen County. Ezzell field Starr County...... El Tanque field Webb County..... Killam and Oilton fields Of these, Benavides, Oilton, Killam and Ezzell have so far proved themselves most important; the Benavides field, Duval County, showing by far the most activity. For the year 1937, therc were 283 wildcat tests drilled in this district, of which 35 were oil producers, 20 completed as gas wells and 228 abandoned as dry holes. Duval County, as usual, received the greatest amount of wildcat drilling, having 21 oil wells, 5 gas wells and 63 dry holes completed during the year for a total of 89 tests. Next came Webb County with 4 oil wells, 4 gas wells and 53 dry holes for a total of 61 tests.The Laredo oil district, South Texas, includes an area of approximately 200 miles long north and south and 75 miles wide, embracing the following counties: Starr, Zapata, Jim Hogg, Webb, Duval and McMullen. The area is relatively old in respect to the production of oil, as the first oil was discovered and produced in the Piedra Pintas field in Duval County on Sept. 10, 1905. Since that date, continuous new discoveries have contributed to the development of this district until, at the present time, it is one of the important oil-producing and gas-producing areas in the world. The year 1937 also had its share of new discoveries in the district, including not only new oil fields but also new sands in already producing pools and important extensions to existing sands and fields. Among the most important field discoveries, by counties, are: Duval County..... Benavides, Sweden, Thomas-Lockhart, Labbe and Lundell fields Jim Hogg County.. Las Animas field McMullen County. Ezzell field Starr County...... El Tanque field Webb County..... Killam and Oilton fields Of these, Benavides, Oilton, Killam and Ezzell have so far proved themselves most important; the Benavides field, Duval County, showing by far the most activity. For the year 1937, therc were 283 wildcat tests drilled in this district, of which 35 were oil producers, 20 completed as gas wells and 228 abandoned as dry holes. Duval County, as usual, received the greatest amount of wildcat drilling, having 21 oil wells, 5 gas wells and 63 dry holes completed during the year for a total of 89 tests. Next came Webb County with 4 oil wells, 4 gas wells and 53 dry holes for a total of 61 tests.

Jan 1, 1938

By John R. M. Hill, Gerald Zink, Fun-Den Wang

The work described in this paper is sponsored by the Bureau of Mines for the purpose of accelerating the drilling of roof bolt holes and reducing the quantity of materials needed to fill each hole. A high-speed, small-hole drill has been fabricated and tested in the laboratory. High Priority has been given to safety, reliability, and compatibility with underground coal mining practice. The combination of drag bits and erosion jets is designed for high penetration rate, long wear life, and uniform hole size in a variety of sedimentary strata. A reliable high-pressure, high-speed swivel feeds water to the bit at about 4 L/min (1 gpm). The duplex hydraulic intensifier which drives the jets has a 40-kW (30-hp) capacity. Results of recent full-scale laboratory testing (Now. 1977) are presented.

Jan 12, 1979

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred, indicated by a *. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1915.) ADAMS, ARTHUR K., Lieut., Co. 2, E. 0. T. S., Camp Humphreys, Va. AMIDON, CLAUDE E., 11th Training Co., Casual Camp, Camp Cody, N. M *BARBOUR, P. E., Capt., Engineer Corps, U. S. A. *BENHAM, W. M., Master Engr., Headquarters Dept., 115th Engrs. A. E. F., Care Postmaster, N. Y. BICKNELL, H. L., Pvt., Co. D, 27th Engrs., Camp Leach, D. C. *BLANDY, S. H. B., Lieut., Royal Horse Artillery, B. E. F.

Jan 10, 1918

New York Meets first Wednesday after first Tuesday of each month. Chairman. PERCY E. BARBOUR, Vice-Chairman. A. D. BEERS, Secretary, 55 Wall St., New York, N. Y. C. A. BOHN,.Treasurer. JOHN V. N. DORR, LEWIS W. FRANCIS. Boston Meets first Monday of each winter month. W.. E. C. EUSTIS. Chairman. R. L. AGASSIZ. Vice-Chairman. E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Cambridge, Mass. ALBERT SAUVEUR, H. L. SMYTH. Columbia Holds four sessions during year. Annual meeting n September or October. W. H. LINNEY, Chairman. OSCAR LACHMUND, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. STANLY A. EASTON. S. SHEDD. Puget Sound Meets second Saturday of each month SIMON H. ASH, Chairman. I. F. LAUCKS, Vice-Chairman. CHARLES SIMENSTAD, Secretary-Treasurer, 425 Lyon Bldg., Seattle, Wash. GLENVILLE A. COLLINS, JOHN N. POTT

Jan 5, 1917

By Michael G. Schill, Mark C. Fischer

Since its introduction several years ago in the United States, the high pressure belt filter press has proven to be a highly cost-effective dewatering device in a number of mining and industrial applications. To evaluate the process and economic factors associated with the dewatering of coal refuse, a comprehensive program of laboratory and on-site pilot studies has been conducted. This paper will summarize findings of this study and discuss advantages of the belt filter press over conventional dewatering methods. The conventional means of dewatering thickened coal refuse involves the use of vacuum disc filters or centrifuges. Due to the high amount of energy used to dewater refuse with these devices it was a logical course of action to apply belt filter press technology to this application, since a belt filter press will require less than 3.7 kW (connected).

Jan 1, 1982

New York Meets first Wednesday after first Tuesday of each month. Chairman. PERCY E. BARBOUR, Vice-Chairman. A. D. BEERS, Secretary, 55 Wall St., New York, N. Y. C. A. BOHN, Treasurer. JOHN V. N. DORR, LEWIS W. FRANCIS. Boston Meets first Monday of each winter month. R. L. AGASSIZ, Chairman. JAMES G. CARLETON, Vice-Chairman. E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology. Cambridge, Mass. W. E. C. EUSTIS, G. A. PACKARD. Columbia Holds four sessions during year. Annual meeting in September or October. W. H. LINNEY, Chairman. OSCAR LACHMUND, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. STANLY A. EASTON, S. SHEDD. Puget Sound Meets second Saturday of each month SIMON H. ASH, Chairman. I. F. LAUCKS, Vice-Chairman. CHARLES SIMENSTAD, Secretary-Treasurer, 425 Lyon Bldg., Seattle, Wash. GLENVILLE A. COLLINS, JOHN N. POTT

Jan 6, 1917

(Members are, urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period April 10 to May 10; I. N. Knapp, Ardmore, Pa. E. P. Mathewson, Anaconda, Mont. Herbert B. Cox, New York, N. Y. H. B. Barling, New York, N. Y. A. McLintock, Brooklyn, N. Y. M. M. Thompson, Morsemere, N. J. Heinrich Ries, Ithaca, N. Y. Howland Bancroft, Denver, Colo. R. M. Catlin, Franklin Furnace, N. J. John H. Adams, Birmingham, Ala. Percy E. Barbour, Candor, N. C. Henry D. Boddington, London, England. A. D. R. Galloway, Qruro, Bolivia. William J. Cox, Denver, Colo. M. K. Rodgers, Westgate, Cal. W. J. Morrison, Toronto, Canada. W. J. Richards has been elected President of the Reading. Coal & Iron Co., succeeding the late George F. Baer.

Jan 6, 1914

By Karl J. Benecke

Though the first patent on a bucket wheel excavator (BWE) was granted in 1881 in the US, this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generation, despite the low heating value of German lignite on the order of 8500 kJ/kg (3600 Btu/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is on the order of 1 to 1.5 to 2.5, hence highly in favour of lignite.

Jan 8, 1979

By B. W. Frazier

At a recent meeting of the North of England Institute of Min ing and Mechanical Engineers, during a discussion upon the com pression of air, attention was called to an apparent anomaly in the phenomena attending the compression. At a subsequent meeting this apparent anomaly was explained by Prof. Herschel, and all the facts observed shown to be strictly in accordance with the laws of thermodynamics. Upon reading the report of the discussion in the published transactions of the society, it occurred to me that an attempt to determine mathematically the amounts of energy (whether in the form of heat or of work) expended and absorbed in compressing air, and causing it to perform work by expansion, might prove of use to some who have not access to any treatise upon the application of the laws of thermodynamics to the compression of air, and who have not the time or the inclination to make such application for themselves. The apparent anomaly noticed was this: If air be compressed, and at the same time, by the sufficient application of a cooling medium, kept at a constant temperature, the indicator diagrams in the

By P. Wynblatt, J. E. Dorn

The effect of strain rate, temperature, and interstitial impurity concentration on the flow stress was investigated in a poly crystalline Fe-2 pct Mn alloy. The temperature dependence of the flow stress was found to be independent of the interstitial impurity concentration, removal of interstitials merely decreasing the atherma1 stress level. Below 160%, the large temperature dependence of the flow stress was interpreted in terms of the Dorn-Rajnak theory of the Peierls mechanism of plastic deformation. Above 160"K, some other thermally activated intrinsic meckanisln seems to be operating. The strong temperature dependence of the flow stress of bcc iron at low temperatures has been studied by numerous investigators and interpreted in terms of several different thermally activated dislocation mechanisms. The following mechanisms have been proposed: a) interaction of dislocations with interstitial impurity atoms1 or with solute atoms in general; b) interaction of dislocations with clusters of impurity atoms;3 c) resistance to the motion of dislocations due to jogs on screw dislocations;* d) resistance to the motion of dislocations due to the Snoeck effect;' and e) interaction of dislocations with the intrinsic resistance of the bcc lattice or Peierls "hills". In previous work: it was found that the plastic behavior of polycrystalline iron containing 2 wt pct Mn (and 100 ppm C + N) is in good agreement with predictions based on the Peierls mechanismlo from 77" to 160°K whereas from 160" to about 370°K another as yet unidentified thermally activated mechanism is operative. The purpose of the present investigation was to determine the effect of interstitial impurities on the temperature dependence of the flow stress, by purifying the previously investigated alloy with respect to interstitial impurities. The investigation revealed that removal of the interstitial impurities to a level that eliminated Cottrell locking and the Portevin-LeChatelier effect (i.e., serrations in the stress-strain curve due to dynamic strain aging) affects neither the strong temperature dependence of the flow stress at low temperatures nor the general characteristics of the higher-temperature behavior. Such purification, however, lowered the athermal yield stress. I) EXPERIMENTAL PROCEDURE AND RESULTS The material used in this investigation consisted of an Fe-2 wt pct Mn alloy having the following additional elements present: 0.004 pct C, 0.006 pct N, 0.05 pct 0, 0.004 pct S, 0.003 pct P, and 0.001 pct Si. This was the same material as that studied in the previous investigation and will henceforth be referred to as the "impure material". The as received -jr by 2 in. hot-rolled bars were cold-rolled to 0.08-in. thickness, recrys-tallized under argon for 30 min at 80O0C, and further cold-rolled to 0.053-in. thickness. Flat tensile specimens 3 in. wide having a 1.625-in.-long gage section were machined from the sheet and then purified. The first stage of purification consisted of holding the specimens at 850°C for 24 hr in a stream of hydrogen saturated with water vapor at room temperature. Material prepared in this fashion will subsequently be referred to as "wet hydrogen purified material". It has been estimated that this type of treatment reduces the carbon content of iron to less than 5 ppm.' The second stage of purification consisted of holding the specimens in a closed system through which hydrogen was circulated past the heated specimens as well as a zirconium hydride getter. The specimens were held at 850°C and the getter at 800°C. The process was continued for 212 hr. The starting material for this process was wet hydrogen purified material. Material prepared in this manner will be referred to as "ZrHz purified material". The technique used was substantially the same as that described by Stein et al.' who have shown that the carbon level at the end of the process is reduced to about 5 parts per billion. The mean grain size of the three materials was found to be -60 C( for the impure material and -160p for the wet hydrogen and ZrHz purified materials. All tensile testing was carried out on an Instron Testing Machine either in controlled-temperature baths or at fixed-point baths such as boiling liquid nitrogen, and so forth. When fixed points were used the temperature was kept constant to better than *1°C whereas in all other tests the temperature variation was less than *2°C. Test of Purity. It was not possible to determine the purity achieved at each stage of the purification because the resulting level of interstitial impurities was near or below the limit of sensitivity of standard analytical techniques. It was possible, however, to obtain a qualitative measure of the extent of purification from the appearance of the stress-strain curves for the three materials. Fig. 1 shows the stress-strain curves for the three different materials tested at 300°K. It can be seen that the effect of wet hydrogen

Jan 1, 1967