Search Documents

By David J. Mack

A survey and critical appraisal of published information about Young's modulus was originally made by the writer because of a complete lack of information about this very important quantity in works on. mechanics, physical metallurgy, physics, and other sciences. It was felt that a comprehensive summary of such information about Young's modulus might be of general interest and may suggest new problems or lines of attack on other problems that involve E. Hence this paper has been prepared even though it is only a review, with no new ideas or experimental data. The references are only those used in assembling the paper. No attempt was made to compile a complete bibliography on the subject of Young's modulus. CalculatioX oP YouNg's Modulus from Theoretical or Empirical CoNsidera-tions Many attempts have been made to compute E from theoretical considerations. The earliest calculations were probably those of Tomlenson (1883) and Souther-land (1891), but Fess'enden4',~ made extensive calculations a few years later and arrived at the relationship: £ = 78.TOw(i)* where V is the atomic volume. In 1923, Peczalski, working from the same standpoint but with more information available on atomic structure, arrived at an identical relationship, which he expressed as: where B is a constant of value about 8 . 107, p is density and mis atomic weight; the atomic volume, of course, being ml p. Portevind4 immediately pointcd out that while the equations of Fessenden and Peczalski were true of the common metals, they gave low values for the refractory metals with high moduli (Fig. I). He showed (Fig. 2) that much better concordance was obtained by means of an empirical equation of the form: F- KT" where K is a constant; T the absolute melting point; V, atomic volume, and a and b constants of value approximately I and 2 respectively. This constant K in the Portevin equation is not necessarily the same for all elements, as shown by Thompson. Other equations for E based upon theoretical considerations have been derived by Honda and Yamada49 and Lasareff.50 The most recent calculations of elastic moduli based upon quantum mechanics are probably those of Fuchs He extended the method of Wigner and Seitz for calculating the lattice energy and compressibility of monovalent metals and computed the elastic constants of lithium, 18

Jan 1, 1946

AN intermetallic compound, Ni3A1, has an ordered fcc structure of type Ll2, and shows peculiar dependence of the yield stress upon temperature; i.e., the yield stress increases by a factor of six upon raising the temperature from 77" to 900K1, 2 This compound is technologically important, since many nickel-base superalloys owe their high-temperature strength to the peculiar yield stress behavior of Ni3Al. The only study of the elastic behavior of this compound was made by Davies and Stoloff,1 who determined Young's modulus of poly crystalline Ni3A1 between 300" and 730°K. The determination of single-crystal elastic constants of Ni3A1 is therefore of interest in connection with dislocation dynamics and is reported in this paper. A single-crystal specimen, 1 by 1 by 3 cm, was cut from an ingot generously supplied by Dr. B. H. Kear of Pratt & Whitney Aircraft. Following initial machining with a Servomet and a surface grinder, the specimen was etched and annealed at 1100°C for 5 hr in vacuum followed by furnace cooling. Two parallel faces were oriented normal to within ±l deg of a [I101 crystallographic axis by the back-reflection Laue technique. The parallel faces were hand-lapped, etched, and polished by the usual metallographic procedures. Final thickness along the [I101 axis was (0.9325 * 0.0005) cm. Chemical analysis gave an average composition of 87.35 pct Ni. Total impurity content is esimated to be no more than 0.1 pct. The elastic constants were calculated from measurements of ultrasonic waves which were propagated along the [110] axis. A longitudinal wave and two shear waves whose displacements are aligned along the [ 110], [li~], and [001] directions, respectively, are necessary in order to completely specify the three elastic constants. Two 3/6-in. quartz transducers were bonded to the parallel faces of the sample with ~ac-seal.3 Although this bond was sensitive to thermal shock, it performed satisfactorily over the entire temperature range for both longitudinal and shear wave propagation. A frequency of 5 mHz was employed in the method of Williams and Lamb4 in order to measure the absolute value of the ultrasonic velocity. The pulse-overlap technique of Mcskimin5 was also used at this frequency in order to determine the shift in the ultrasonic velocity

Jan 1, 1970

By B. B. Rath, Hsun Hu, R. S. Cline

FOLLOWING the techniques used by Beck and co-worker~ "~ the characteristics of selective growth in the recrystallization of a zone-refined aluminum single crystal, rolled 80 pct at -78°C in the (110)[112] orientation, have been studied. The material was 99.999+ pct pure. The as-grown crystal had a resistance ratio, R(298°K) /R(4,2°K), of approximately 5000. The method of preparation of the single crystals and the necessary precautions in handling them during rolling in order to avoid recrystallization in locally distorted regions were described in an earlier paper.3 The rolling texture of this zone-refined aluminum crystal is practically identical with that of less pure aluminum crystals rolle! in the same orientation, i.e., a very sharp (110)[112]. Random nuclei were provided by artificial nuclea-tion by abrading one face of the rolled crystal on 600-grit emery paper in a random fashion. The thin layer of disturbed metal recrystallized at room temperature into fine grains almost immediately. An X-ray diffraction pattern was taken from the abraded surface of the crystal, and the relative intensities of the various reflection peaks were compared with those obtained from a powder specimen. As shown in Fig. 1, the relative intensities of the various peaks from the recrystallized layer varied somewhat from experiment to experiment, depending presumably on the abrading technique. However, the texture of the recrystallized layer produced by this method is nearly as random as that of a powder specimen. Fig. 2 shows the texture determined from the "growth side" (face opposite the abraded surface) of the crystal after it was kept at room temperature for 100 hr. The specimen was only partially recrystallized, as shown by the remaining deformation texture. The new orientations are derived from the recrystallized grains grown through the thickness of the crystal from the "nucleation side" (the abraded surface). Fig. 3 shows the texture after complete recrystallization produced by annealing at 60°C for 1 hr. The arrows indicate 40-deg rotation around the (111) axes of the deformation texture. The microstructure of a completely recrystallized specimen is shown in Fig. 4. As shown in Figs. 2 and 3, the texture of the re-crystallized grains grown from the nucleation side to the growth side is essentially the same as that observed in less pure aluminum' (99.994 pct) and dilute alloyz crystals rolled in the same orientation. How-

Jan 1, 1968

By Jacob T. Wainwright

AS a means for increasing the efficiency in modern blast-furnaces by supplying to them blast of a much higher temperature than is now possible, the writer offers as a suggestion a modification in the construction of regenerative hot-blast stoves. Stated briefly, the plan proposed is to pre-heat both the gas and the air for its combustion in a manner similar to that generally adopted in Siemens openhearth furnaces. After thus carrying the temperature of the stove to a point much higher than that common in hot-hlast stoves, the cold blast passes through it. Without entering into the details relating to the reversing valves and the system of flues, the general plan may be outlined as follows, referring to the accompanying drawings: The valves are so placed in heating up the stove that the blast-furnace gas enters at B, Fig. 1, and the cold air for combustion at A. Ascending in flues, F and E, respectively, combustible gas and air meet and mix in the combustion-chamber, I. Flowing through K, they descend through the flues, G and H, escaping through the chimney. In this manner the walls of the combustion. chambers, I and L, are highly heated, and the right-hand side of the stove is carried to a higher temperature. By reversing the valves, blast-furnace gas enters at C and cold air for combustion at D. Both are pre-heated in their ascent through the flues, G and H. They burn in the combustion-chamber, L, and the hot gases of combustion, flowing through K, I, E and F to A and B, heat the left-hand side of the stove. In this manner the stove is carried to a temperature greater than that of those now generally in use, in which air and gas are burned without preliminary pre-heating. In the plan proposed, that side of the stove will, of course, be relatively cooler through which cold air and furnace-gas last passed in its ascent to its combustion-chamber. After having sufficiently heated the stove in the manner outlined, the cold blast is admitted through all the flues, A, B, C and D. It ascends through the highly-heated regenerative material to the chambers at the top and descends through the flue, P, Fig. 2 (dotted

Jan 1, 1889

By Charles S. Larkey

Numerous papers have been published on the use of graphic methods for determining the best curve for estimating the production decline of oil wells but, as far as the writer has been able to ascertain, nothing has been published showing how curves may be worked out mathematically that will conform most closely to the production data under consideration in any given instance; hence the writer has endeavored to show just how such application can be made. Among the valuation engineers, two types of curves are in current use for the representation of the decline in production of oil wells. One may be represented by the equation, y = krx; this is sometimes known as a percentage curve, for the production for any period is multiplied by a constant rate or percentage to obtain the production for the succeeding period. It appears as a straight line on semilogarithmic cross-section paper. The other curve may be represented by the equation, y = kxn, and is shown as a straight line on logarithmic cross-section paper. In each equation, y represents the number of barrels produced in a given period of time, and x the successive periods of time. The other letters are constants to be determined for each well, or group of wells considered in arriving at the most probable curve to represent the rate of production for a given property. From this the underground reserves may be estimated by extrapolation, or by extending the curve beyond the last known period of production to show the most probable production values for the future. Application to the Burbank Pool Fig. 1 relates to a property in the Burbank Pool, Osage County, Okla. The production is shown as an average per well per month, is plotted to the vertical scale of barrels on the left-hand margin and to the horizontal scale of months at the bottom of the chart. In column y, the number of barrels is listed beginning with May, 1922, as the first month on which to base a decline curve. The type of curve used is of the form, y = krx, or, expressed in logarithms, log y = log k + x log r, in which log k and log r are constants to be determined so that the curve will most closely approximate the production data given.

Jan 1, 1925

The State Mining Experiment Station, Missouri School of Mines and Metallurgy, Rolla, Mo Charles H. Fulton, Director of the School of Mines Martin H. Thornberry, Director of the Mining Experiment Station. From the State Mining Experiment Station are issued all the general and technical bulletins of the School of Mines The latest bulletin containing a complete list of publications will be sent upon application to the Director of the Station Residents of the state may obtain bulletins as issued without charge, or may ask to be placed on the mailing list. Nonresidents should write to the Director for further information concerning specific bulletins. From the long list of bulletins the following have been care¬fully selected as being most likely to interest the geologist and the mining engineer. Vol 8, No. 1 (1916), Bibliography of concentrating ores by flotation, by J Cunningham, vol 1, No 3 (1912), Some apparatus and methods for demonstrating rock drilling and the loading of drill holes in tunneling, by L E Young, vol 2, No 1 (1915), Comparative tests of piston drill bits, by C R Forbes and L M Cummings; vol 2, No 3 (1916), Cupellation losses in assaying, by H. T Mann and C. Y Clayton; vol 4, No 1 (1917), The hydrometallurgy and electrolytic precipitation of zinc, by F D. James; vol 4, No 2 (1917), The effect of additional agents in flotation, pt 1, by M. H. Thornberry and H T. Mann, vol 5, No 1 (1919), The carbonization of Missouri cannel coals, by H L. Dunlap, K. K. Kershner and V. X Smiley. Vol 5, No. 4 (1921), Coal mining methods in Missouri, by W W Weigel, vol 6, No 1 (1921), The problem of the St Peter sand¬stone, by C L Dake, 50 cents, vol 6, No. 2 (1922), Bibliography on the electrothermic metallurgy of zinc, by B M. O'Harra, vol 6, No. 4 (1923), Experiments on the distillation of zinc from complex zinc-lead-silver ores, by B M. O'Harra and E S. Wheeler, vol 7, No 3 (1924), Underground loading devices, by C. E. van Barneveld, 81; vol 7, No. 4 (1924), Briquetting of zinc ores, by B. M. O'Harra; vol. 8, No 2 (1925), A treatise of Missouri clays, by M. H. Thornberry.

Jan 1, 1933

By B. D. Cullity

GOLD and beryllium form an intermediate phase composed of the two metals in equal atomic proportions and having the formula AuBe. According to Winkler,1 this phase probably exists in two modifications: beta, stable below about 600°C, and alpha, stable between 600°C and the melting point, about 740°C. Only the low- temperature beta form will be considered in this paper. EXPERIMENTAL PROCEDURE The gold used had a fineness of 999.75 to 999.85, balance mainly silver, and the beryllium purity was better than 99.8 pct. AuBe was prepared by melting the constituents in a beryllia crucible in an evacuated induction furnace. After melting and thorough mixing, the alloy was allowed to solidify in the crucible. No difficulty was encountered in obtaining a homogeneous ingot. Both chemical analysis and microscopic examination of the ingot showed that the alloy was essentially one phase, containing 50 at. pct gold. The alloy was quite brittle and powder samples could easily be pre- pared by grinding in an agate mortar. The X-ray diffraction patterns were made with CuK-alpha radiation in a Debye-Scherrer powder camera 57.3 mm in diameter. The film was placed unsymmetrically in the camera in order to afford a basis for am-shrinkage corrections. A sample homogenized at 5o0°C gave the same diffraction pattern as a sample taken from the as-melted ingot. GENERAL RESULTS The diffraction pattern of AuBe was readily indexed on the basis of a simple cubic lattice with ao = 4.659 ± 0.001kX. If the unit cell is assumed to contain four AuBe "molecules," the calculated X-ray density is 13.46 grams per cc as compared with the measured density of 13.55 gm per cc. The only missing reflections in the dsraction pattern are (100) and (220) (see Table I). Since these missing reflections are not those characteristic of body or face centering, the lattice of AuBe must be simple cubic. To locate the positions of the atoms within the unit cell, two possibilities had to be considered: I. The structure was disordered and there were eight positions to be filled by an "average" gold-beryllium atom. That the structure was disordered seemed unlikely since the lattice parameter did not vary with composition in alloys containing some- what more and somewhat less than 50 at. pct gold, indicating a fixed composition for AuBe.

Jan 1, 1947

By B. D. Cullity

Gold and beryllium form an intermediate phase composed of the two metals in equal atomic proportions and having the formula AuBe. According to Winkler,' this phase probably exists in two modifications: beta, stable below about 600°C, and alpha, stable between 600°C and the melting point, about 740°C. Only the low-temperature beta form will be considered in this paper. Experimental Procedure The gold used had a fineness of 999.75 to 999.85, balance mainly silver, and the beryllium purity was better than 99.8 pct. AuBe was prepared by melting the constituents in a beryllia crucible in an evacuated induction furnace. After melting and thorough mixing, the alloy was allowed to solidify in the crucible. No difficulty was encountered in obtaining a homogeneous ingot. Both chemical analysis and microscopic examination of the ingot showed that the alloy was essentially one phase, containing 50 at. pct gold. The alloy was quite brittle and powder samples could easily be prepared by grinding in an agate mortar. The X-ray diffraction patterns were made with CuK-alpha radiation in a Debye-Scherrer powder camera 57.3 mm in diameter. The film was placed unsym-metrically in the camera in order to afford a basis for film-shrinkage corrections. A sample homogenized at 500°C gave the same diffraction pattern as a sample taken from the as-melted ingot. General Results The diffraction pattern of AuBe was readily indexed on the basis of a simple cubic lattice with ao = 4.659 + 0.001kX. If the unit cell is assumed to contain four AuBe "molecules," the calculated X-ray density is 13.46 grams per cc as compared with the measured density of 13.55 gm per cc. The only missing reflections in the diffraction pattern are (100) and (220) (see Table I). Since these missing reflections are not those characteristic of body or face centering, the lattice of AuBe must be simple cubic. To locate the positions of the atoms within the unit cell, two possibilities had to be considered: I. The structure was disordered and there were eight positions to be filled by an LCaverage" gold-beryllium atom. That the structure was disordered seemed unlikely since the lattice parameter did not vary with composition in alloys containing sornewhat more and somewhat less than so at' pet gold, indicating a fixed composition for AuBe.

Jan 1, 1947

By H. J. Engell, W. Frank, A. Seeger

SWISHER and ~urkdogan' have determined the solubility of oxygen in a iron. They found it to lie between 7 and 10.5 at.-ppm at 881°C. Using earlier work on the permeability of oxygen in bcc iron,' they arrived at the following expression for the diffusion coefficient of oxygen in bcc iron (k = Boltzmann's constant, T = absolute temperature): where The present authors3 have estimated the activation energy QD for the diffusion of oxygen in bcc iron in two different ways from various experimental data.2'4"6 In the first method QD + QS (QS = heat of solution for oxygen in bcc iron in thermodynamic equilibrium with solid FeO) was determined either from data on the reduction of FeO with hydrogen4 or from measurements of the internal oxidation of silicon in a iron.5 Using an estimate of QS from investigations of the oxygen solubility in 6 iron2 (in thermodynamic equilibrium with molten FeO) Q = 0.97 ev or Q~ = 1.06 ev were obtained. From the magnitude of these values it was concluded that oxygen migrates interstitially in bcc iron and that consequently the activation energy QD for diffusion of oxygen has to be identified with the migration energy E~ of the oxygen atoms. Therefore, for a second estimate of QD from the diffusion coefficient of oxygen in 6 iron at 1450" ~,~ we used the theoretical expression:3 (a = length of elementary cube edge, m = mass of interstitially diffusing atom, sM = migration entropy), applicable to diffusion via the octahedral interstices in bcc lattices. Taking sM = 3.8 k (migration entropy of carbon in a iron), one gets Q = 0.90 ev. Hence, in Ref. 3 Q = (0.98 *0.1) ev was proposed as a plausible value for the diffusion energy of oxygen in bcc iron. sM + 9 (9 = solution entropy for oxygen in bcc iron) can be determined from permeability measurements.4 Using the above-mentioned estimate for QS , the following expression for the solubility c (atomic concentration) of oxygen (in thermodynamic equilibrium with solid FeO) in bcc iron was derived: From [4] the solubility of oxygen at 881°C in a iron is calculated to lie between 0.6 and 12 at.-ppm. We see that the solubility determined by Swisher and

Jan 1, 1969

By B. D. Cullity

Gold and beryllium form an intermediate phase composed of the two metals in equal atomic proportions and having the formula AuBe. According to Winkler,' this phase probably exists in two modifications: beta, stable below about 600°C, and alpha, stable between 600°C and the melting point, about 740°C. Only the low-temperature beta form will be considered in this paper. Experimental Procedure The gold used had a fineness of 999.75 to 999.85, balance mainly silver, and the beryllium purity was better than 99.8 pct. AuBe was prepared by melting the constituents in a beryllia crucible in an evacuated induction furnace. After melting and thorough mixing, the alloy was allowed to solidify in the crucible. No difficulty was encountered in obtaining a homogeneous ingot. Both chemical analysis and microscopic examination of the ingot showed that the alloy was essentially one phase, containing 50 at. pct gold. The alloy was quite brittle and powder samples could easily be prepared by grinding in an agate mortar. The X-ray diffraction patterns were made with CuK-alpha radiation in a Debye-Scherrer powder camera 57.3 mm in diameter. The film was placed unsym-metrically in the camera in order to afford a basis for film-shrinkage corrections. A sample homogenized at 500°C gave the same diffraction pattern as a sample taken from the as-melted ingot. General Results The diffraction pattern of AuBe was readily indexed on the basis of a simple cubic lattice with ao = 4.659 + 0.001kX. If the unit cell is assumed to contain four AuBe "molecules," the calculated X-ray density is 13.46 grams per cc as compared with the measured density of 13.55 gm per cc. The only missing reflections in the diffraction pattern are (100) and (220) (see Table I). Since these missing reflections are not those characteristic of body or face centering, the lattice of AuBe must be simple cubic. To locate the positions of the atoms within the unit cell, two possibilities had to be considered: I. The structure was disordered and there were eight positions to be filled by an LCaverage" gold-beryllium atom. That the structure was disordered seemed unlikely since the lattice parameter did not vary with composition in alloys containing sornewhat more and somewhat less than so at' pet gold, indicating a fixed composition for AuBe.

Jan 1, 1947

By W. D. Robertson

A considerable quantity of experimental data is available on the effect of time, temperature, work-hardening and composition on the mechanical properties and corrosion resistance of aluminum alloys. There is, however, little unity of purpose or generality in most of the studies and, because the number of variables is large, the results often are not applicable to the problems that arise in practice. Furthermore, the customary expression of the effect of different variables as separate curves or as three-dimensional diagrams with time, temperature and the dependent variables as coordinates, renders the task of selecting the optimum time and temperature of precipitation treatment, with respect to their simultaneous but unequal effect on the various properties, exceedingly difficult. The introduction of precipitation treatments to raise the yield strength of 24S-type alloys has created a need for a method of correlating and summarizing the effect of time and temperature on the mechanical properties and susceptibility to intercrystalline corrosion. Correlation is particularly desirable because the choice of time and temperature is of necessity a compromise to achieve the best possible combination of properties, and the optimum conditions cannot be accurately specified unless the data are in a form in which the alternatives can be readily compared. Therefore, the work described here was undertaken to find a common relationship that would be capable of expressing the effect of precipitation time and temperature on the various properties and by means of which the relative effects could be correlated and their interpretation facilitated. REVIEW OF PREVIOUS WORK In connection with an investigation of the interrelation of age-hardening and creep performance of nickel-silicon-copper alloys, Jenkins and Bucknall1 demonstrated that the time required to attain maximum hardness and tensile strength could be expressed by a relationship of the form: t = K. 10m/T (I) where t is the time in hours and T the temperature of aging, expressed in degrees absolute, and m and K are constants. They also pointed out that this expression is analogous to that which describes the change of the diffusion coefficient D with temperature; namely, D = Ae-Q/RT (2) Later, Cohen used this relationship in studies of the mechanism of age-hardening of a silver- rich copper alloy2 and of duralumin. 3

Jan 1, 1945

[A Editor's Note: Annual Reviews of various subjects and areas are found in February issues of Mining and Metallurgy and Mining Engineering. These Annual Reviews are not listed per se in the Index. Abating Stream Pollution in Anthracite Coal Fields. ME Mar 50 Abbadia San Salvatore mine, Italy. T178, 297 Abbott, C.E.: Limestone Mine in the Birmingham District. With Discussion. T129, 62 ABC Typifies Trend to Mechanized Mining and Coal Preparation. ME Dec 50 Abel, J.F.: Statistical Analysis of Tunnel Supporting Loads. T235, 288 Sulzbach, J. F., and Walker, D.K.: Ice Tunneling in Greenland. ME Jun 59 Aberfoyle tin mines, sphalerite, chalcopyrite, stannite, as intergrowths. T214, 1147 Abnormal Behavior of Some Ore Constituents and Their Effect on Blast Furnace Operation, The. T241, 1 Abrams, C.J.: Industry's Responsibility in Postwar Economy. M&M Mar 45 and Haley, D.F.: History of Crushing and Milling at Climax. M&M Jun 46]

Jan 1, 1972

Theo. B. ComstocK, Los Angeles, Cal. (communication to the Secretary*):—Mr. Blake's recent paper upon this topic undoubtedly partly explains the rationale of a part of the known facts bearing upon discolorat'ion and encrustation of rocks. His quotation from Humboldt, with reference to certain South American examples, may be questioned in the light of further facts, which do not appear to bear out the great traveler's theory of causation. There is no available evidence that the waters of the tropical rivers referred to by Professor Blake contain dissolved organic matter in the varying proportions required to demonstrate Humboldt's guess, nor do the concomitant facts in any manner bear out the hypothesis that the blackening in one case and its absence in the other may, perhaps, be traced to differences in the chemical reactions of the respective waters. Careful consideration of Professor Blake's illustrations, in connection with numerous personal observations extending over widely-scattered areas, convinces me that elements of

Jan 1, 1905

By Leonard Grimshaw

THE idea of bonding two dissimilar ferrous metals, and making use of both, is an old one. Tips have been brazed onto tool shanks for many years. The bonding of larger pieces to form whole bars and sheets has also been accomplished, but has received little attention in the technical literature, although a number of patents have been issued covering various methods for its accomplishment. There are three main motives behind the manufacture of composite steels. One is that the physical properties of one steel may supplement those of another; a useful, but at the same time, hard, brittle steel may be backed by a soft ductile one, or a stainless steel may be backed by a steel possessing greater strength. Another motive is direct lowering of cost; an expensive steel may be backed by a less expensive one, bringing down the cost of the piece as a whole. The third motive is an indirect lowering of cost, as when a useful steel is backed by a steel that is easier to machine, so that machining cost on a finished product is lowered considerably. Often more than one of these motives lead to a decision to use a com-posite steel.

Jan 1, 1936

By William M. Shepard

The Tintic mining districts of central Utah com- prise one of the major silver-lead producing areas in the United States. Ore valued at nearly $450 million has been produced from these districts since the initial discoveries, in 1869, of veins cutting the Silver City monzonite stock. Subsequent production from the famous manto-type "ore runs", which characterize the Main Tintic district, was followed during the past 40 years by discovery of the blind orebodies of the East Tintic district, including the famous Tintic Standard mine and the most recent discovery, the Burgin mine, currently being brought to full production by Kennecott Copper. The occurrence of blind orebodies of exceptional size and grade in both the Main and East Tintic districts has made this area a field laboratory of major importance for the study of geochemical dispersion halos and alteration features associated with known ore, and has led to the discovery of additional concealed orebodies. The larger share of the basic data-gathering and interpretation has been done by members of the U.S. Geological Survey who have been studying the Tintic mining areas since before the turn of the century. These studies have been supplemented and expanded by the geological staffs of the local operating mining companies, by exploration geologists and by students.

Jan 4, 1966

THERE are three chief production zones of tungsten ore in China. In the Province of Kiangsi mines are located at Kanchow, East River, and West River. Their combined production is understood to amount to 300 to 350 tons of ore per month, and their original exportation is made through the port of Kiukiang, largely to Shanghai. The second zone is in Kwangtung Province, the mines there being at Tayulin. Produc-tion reaches about 200 tons per month and cargo is gen-erally exported through the port of Hong Kong. In the Province of Hunan approximately 25 tons of ore are produced monthly in the mines at Ton-on. Tungsten ore from Kiangsi and Kwangtung Prov-inces is generally about 70 per cent WO, (tungstic acid), while that from Hunan is of lower quality, run-ning about 65 per cent WO3. Kiangsi ore is received from the mines in 100-1b. and Hunan in 224-lb. gunny sacks. No repacking is done except as it is made neces-sary by the condition of the sacks. Kiangsi Province contains the Chinese districts pro-ducing the largest amount of salable wolframite or tungsten. Many districts west and south of Kiangsi have been found to have wolframite deposits.-Com-merce Reports.

Jan 1, 1928

By W. A. Vine

When a hole is made in a stressed solid, such as rock pierced by mine openings, equilibrium of the solid is destroyed. To restablish that equilibrium the stress condition in the rock surrounding the opening becomes rearranged. This rearrangement may or may not develop local stresses in the vicinity of the opening which exceed the elastic strength of the rock. Since stability of the opening depends, therefore, on the strength of the naturally occurring rock surrounding the opening, this rock is an engineering material of construction, and all rock affected by the associated opening or system of openings may be considered a structure. The term invert is chosen to describe the formation of the structure built from the inside, as it were, and a consequence of mining rather than an entity built for a purpose. By definition, an invert structure is formed when openings are made underground and is com- posed of that material on the solid side of a rock-air interface wherein the stress condition is affected by the associated opening or system of openings. The shape of an invert structure is never clearly defined; the skin of the structure may be mapped, and even described, but the boundary of the structure within the solid rock mass must be arbitrarily set.

Nov 1, 1955

By Samuel Taylor

IF I LIVE another fourteen months and am still con-nected with the coal industry, I shall then have com-pleted a half century with it. Since May, 1874, when .I first entered the bituminous workings as a miner, I think I have held almost every position connected with a mine except possibly that of mule driver, for which I was unfitted by reason of my religious upbringing. We are all agreed, at least I have not heard it contra-dicted, that there is serious over-production in the bituminous industry. This has come about in various ways and is easily explained. During the Fuel Admin-istration, I recall making an estimate of the possible output of the bituminous mines of the country provided they were given a full force of men and a full-car supply; my estimate was a little over a billion tons a year. A few months ago, the late Francis H. Peabody, of Chicago, made a practically identical estimate. If, however, both of these conditions should happen con-currently, there would very soon be no market for the coal, and many of the mines would close down. Even today, if 10 per cent. more cars were furnished, to the bituminous mines, market prices would drop very seriously.

Jan 4, 1923

By Arthur L. Walker

In June, 1893, while I was with the Old Dominion Copper Co. at Globe, Ariz., I received an offer to take charge, as manager, of the Baltimore Electric? Refining Co. which had recently built a plant at Baltimore, Md., having a capacity of about 1200 tons of electrolytic copper per month, using the Hayden series system. This was a very large output, for in those days the plants were small and the art was in its infancy. At the beginning of 1893 there were 11 electrolytic refineries in the United States, most of them using the multiple system. The Hayden series system was used at Baltimore and Bridgeport and the Smith series system was in operation at the Electrolytic Copper Co. at Ansonia, COM., and at the Pennsylvania Salt Co. at Philadelphia. In the latter system the plates were placed in a horizontal position, but the operating difficulties were so numerous it was soon discarded. The total production of these 11 plants in 1892 was very small; I have not been able to discover reliable figures of production. There were about thirty electrolytic copper refineries in the world that year, according to Titus Ulke, and the entire production of these

Jan 1, 1932

By F. S. Crawford

IRON and copper are mined in the Lake Superior district. The iron mines of the district have the best safety record for that industry in the country as a whole, while the copper mines of the district rank second in two of the four years recorded (Table 1). In Utah copper comes mainly from open-pit mines, which enables that state to lead easily in safety. All of the Michigan production comes from deep under-ground workings. About 60 per cent of the iron miners in St. Louis County, Minnesota, are employed at open-pit mines; this favorably affects the combined open-pit and underground accident-frequency rate, as this county pro-vides most of the Minnesota-mined iron ore. In Michigan, however, there are few open-pit mines, the bulk of the production coming from underground mines, while all of the Wisconsin production, just across the state line from Michigan, is from underground mines. In spite of the fact that fewer mines in Michigan use the safer open-pit method, the iron-mining industry of that state maintained a consistently low record from 1931 to 1934; however, it was many points behind its nearest com petitor, Minnesota, with its much greater production from open-pit mines.

Jan 1, 1939