Search Documents

By Peter F. Weiss, H. Riedler, I. M. Moschitz, A. Olsacher, G. B. Fettweis

CONTENTS : 1. NATURAL FACTORS Geology Petrography and Rock Mechanics Mining System Orientation Rock Bolting System Movability of the Ore Grain Size Distribution Permeability Contamination Value of the Ore Hydrology 2. TECHNICAL FACTORS Height Length and Width Drawing Areas Time Factor Water Predrainage Surf ace Draining Underground Draining Advancing Slitting Sequence of Development Initiation of the Caving Process Drawing Rate 3. SPECIFIC MINING RULES Advancing Development Drawing Rate Interruption of Drawing (Water Distribution, Concentration of Mud, Dilution) Blasting 4. CONTROLS Safety Controls for Operation Computerised Drawing Control Structure of the Computer Program Hard Ware Print Outs 5. SUMMARY 6. ACKNOWLEDGEMENTS 7. REFERENCES Under the heading "Development System for Block Caving under Severe Conditions" a report was presented to this congress regarding a magnesite mine using block caving for several years. On account of the experience gathered in this mine and the results of far reaching exchange of experience, as well as under due consideration of the international literature it is tried to systematically list and briefly discuss the following factors that have to be considered for development and draw control of block caving. 1. NATURAL FACTORS It is self evident that this implies all those circumstances given by nature and which cannot be altered by man. Any mining activity is subjected to those and the success is depending on how far technology can be adjusted to those conditions. Geology Deposits of considerable thickness with rather steeply inclined flat-faced contacts are optimal for block caving. While vertically there is practically no limitation- for the deposit, theoretically, the smallest horizontal basis apt for operating block caving is the minimum area necessary to get the rock to completely cave in by undercutting and drawing. Practically, only consider- ably bigger main dimensions are found, mainly because of technical factors (machinery and equipment) and economic factors (cost ratio of exploration vs. development, danger of contamination).

Jan 1, 1981

By I. C. Edwards, G. E. Agar

INTRODUCTION Many research efforts over the past years have been devoted to the study of energy consumption in comminution and the characteristics of the broken material. The old "laws" have been superseded by more general methods of analysis1,2,3 but these methods have not received much attention outside the laboratory. The work to be described here was done in order to obtain scale-up information on wet rod milling of sylvinite. EXPERIMENTAL A 30 x 51 in. Denver rod mill with a scoop feeder was used for these tests. Ore was fed from a variable speed screw conveyor into the feed box along with saturated brine. The mill was filled to approximately 45% of its volume with 2400 lbs of a mixed rod charge. The minimum possible feed rate was 2.5 tph and the practical maximum for this mill was 8 tph. Individual tests were run by setting the solid feed rate, then adjusting the brine flow rate to give the desired pulp density. After steady state, as evidenced by constant discharge pulp density, had been reached, samples of the discharge were taken at 15-minute intervals. These samples were filtered, washed with alcohol, dried, then screened on Tyler screens using a Ro-tap shaker. The sylvinite feed was regular plant feed that had been scalped at 20 mesh and was tapped from the coarse ore bins. It had been previously passed through a roll crusher set at 3 inches and after scalping was essentially minus 1 in. plus 20 mesh. RESULTS The screen analysis of samples from each series of tests was plotted on double logarithmic scale paper to determine the reliability of the series. In some cases, a faulty sample or screening procedure dictated that the results of one test be discarded. The criterion is a simple one — if the slope of one plot was noticeably different from the others in the series, it was discarded. The only cases that caused difficulty were those in which the brine was not thoroughly displaced from the solids. When this occurred agglomerates were easily identified on the screens and the whole of the sample was retained on 3 or 4 screens. There were no border line cases. The number N given in Table 1 is the number of size analyses that were pooled to form the data shown in Fig. 1. While examining the reliability of the sizing and sampling by plotting the data, it became apparent that there was no significant difference between grinds made at 50 and 60% solids. For the analysis given here, these tests were regarded

Jan 1, 1967

By Ingvar Janelid

DURING the last ten years, in the effort to save manpower and costs, methods of drilling and blasting in Sweden have changed and developed in a revolutionary manner. These developments have been accompanied by extensive alterations in methods of tunneling and in mining technique. Since the end of the 1940's there has been a 100 pct change-over in Sweden to the use of tungsten carbide tipped drill steel. Both investigations and practical results have shown clearly that a tungsten carbide chisel bit fastened directly on the drill steel is the most economical for Swedish conditions. This applies to drill steel up to the longest size it is practical to handle. In terms of drilling footage, durability of the drill steel and the tungsten carbide bit is generally the same. In this respect, therefore, a detachable bit offers no advantage over integral steel. Transportation of integral steel to the grinding plant, instead of detachable bits only, involves heavier work, but this is counteracted by placing grinding plants closer together or by grinding at the working place itself. The drilling rate with integral steel is higher, the trouble of changing bits is avoided, and the difficulties which always arise with joints are eliminated. At present steel dimensions are usually 7/8 in. with a shank 41/4 in. long, whereas the international standard shank was formerly 31/4 in. The longer shank renders possible a better guide control of the steel and consequently longer life for the rotation chuck and the water-flushing pipe. After extensive experiments and investigations, agreement has been reached in Sweden on certain series of standards, shown in Table I. Other steel dimensions are, of course, available for special purposes. The standard drill-steel set begins with a 34-mm diam and has a length interval of 2 2/3 ft. On the other hand, for ordinary drifting it has been proved more economical to use greater length intervals on the steel, so only one steel change is required for a 61/2-ft round. Moreover, owing to the relatively close hole spacing necessary in a drift round, it has been possible to reduce the diameters of the tungsten carbide bits. This results in faster and cheaper drilling. As shown by the table, the lengths of drill steels for normal drifting are 33/4 ft and 71/2 ft, with 29 and 28-mm diam bits. During the last few years operators have begun to use 3/4-in. drill steel in place of the 7/8-in. drill steel chiefly employed earlier. This is a valuable development in drilling technique, particularly in view of

Jan 1, 1955

By C. Dinis da Gama

Because of the growing importance of back analysis for the interpretation of rock slope failures, particularly in open pit mines, it is suggested a methodologic sequence of activities for dealing with those problems. The principal mathematical tools for the interpretation of the most common mechanisms of slope failures are reviewed, including methods of stress and strain analysis, which seem to be more powerful for parametrization studies, and for developing more realistic explanations of slope behaviour, such as the measurement of displacements. An application of those methods is described, using slope failures detected in a Brazilian uranium mine (Cercado), thus providing reliable shearing strength parameters for the rock mass discontinuites, which were used in the final pit design. The concept of using backanalysis results to supply input data for pit design was implemented by means of the excavation of an experimental trench within mine limits, where specific instruments were installed, and several slope failures were monitored and backanalysed, in order to yield information about sliding mechanisms in the future open pit.

Jan 1, 1983

By John V. Beall

Monotonous flood planes flanked either side of the road as we drove in the embassy car from the airport to downtown Seoul. We crossed the brown waters of the Hann River, meandering over mud flats. A great, gnarled tree bore beautiful fall colors of gold. "That is a Ginko Tree, the oldest living fossil, probably a hundred million years old;" said Jean W. Pressler. Compared to other cities of the Far East, the traffic in and around Seoul was sedate. Few motorcycles or bicycles, and little superfluous horn tooting. "This is the best season in Korea. We have long beautiful springs and falls," said Pressler, chief of the mining branch of USAID, and he continued with a briefing on the country.

Jan 8, 1969

By H. Warlimont

In recent investigations of the microstructure and crystallographic features of martensite by electgon microscopy,', '9 thin films (about 50 to l000A in thickness) have been used as specimens. It was found by W. Pitschl ,2 that the lattice relationships between the supefiaturated fcc matrix and the martensite formed in thin films were different from those observed after transformation in bulk material. Corresponding differences are to be expected in nucleation and in reaction kinetics in the formation of martensite in thin films, but have not yet been reported. In the course of the preparation of thin films of iron-base alloys for investigation by electron microscopy it was observed that films of alloys, whose martensite formation temperature (Ms) was below room temperature, formed martensite during the electrochemical thinning process conducted at or above room temperature. The chemical compositions and approximate bulkM,-temperatures of the three materials on which this observation was made are listed in Table I. The alloys were vacuum-melted from high-purity metals. It can be seen that the effect occurred in alloys that contain only sub-stitutional components as well as in alloys that contain carbon as an interstitial solute. The appearance of martensite formed in this manner is illustrated in Fig. 1, which represents a polished film of alloy No. 1 at XI0 magnification. The martensite plates can be recognized by their surface relief effects. In addition, heavily strained (owrinkledo) austenite can be seen near the edges of the film where it is thinnest and transformation stresses or strains can be accommodated by plastic deformation most easily. The nonuniform distribution of transformed regions is probably due to the varying thickness of the film. These observations were common to all materials listed in Table I. Because effects of supercooling or straining can

Jan 1, 1962

By T. H. Oxnam

INTRODUCTION. THE predominating value of the ores now being treated by the Palmarejo and Mexican Gold Fields, Ltd., is silver, although some gold is also carried. The present method of treatment consists of wet-crushing and concentrating, followed by the cyanidation of the unroasted sands and slimes. The sands are treated by leaching and the so-called accumulated slimes by a system of agitation and decantation. It is only within very recent years that the cyanidation of unroasted silver-ores has been commercially successful. In fact, at the time operations were begun at the cyanide-plant at Chinipas, February, 1902, I knew of no other leaching-plant treating similar ores successfully. The cyanide treatment of the Palmarejo ores differs but little from the ordinary practice in cyaniding gold-ores; and perhaps but little, if any, new information concerning the metallurgy of silver is to be gleaned from it. PALMAREJO MINE. The Palmarejo mines are located in the southwestern part of the State of Chihuahua, Mexico, on the foothills of the Sierra Madre mountains, at an elevation of 3,200 feet. The mills, 12. miles distant, are situated on the Chinipas river, near the town of Chinipas, which is about 150 miles northeast of Agiabampo, on the Gulf of California. Supplies are shipped via this port as this route is the best and most direct to the property. The ore-bodies in the Palmarejo mines have been deposited. along a series of rock-fractures, caused by an intrusion of eruptive rock. The most important of these fractures or fissures, both in width and value, are the Prieta and Blanca veins, which.

Jul 1, 1905

By John Chipman, Peter J. Koros

The distribution of copper between liquid silver and liquid iron, Fe-C, and Fe-C-Si alloys was studied at 1600°C. From the data and the activity of copper in silver obtained from the phase diagrams, the activity coefficients of copper in iron up to 3 atomic pct are log y, = 0.90 — 2.4 N, and y": = 8.0. The effect of carbon up to saturation is expressed as log y = 1.8 Ni. The effect of silicon up to 11 atomic pct is insignificant. SLOWLY rising copper content of steel being produced is focusing attention on the lack of information on the behavior of copper in liquid steel. Chou' measured the activity coefficient of copper in liquid iron through its distribution between liquid silver and iron. He obtained a value of 9.12 at infinite dilution. Chipman' calculated the activity coefficient of copper in liquid iron at 1600°C from the phase diagram and obtained a value of 12. Ameiln and Pfeiffer- investigated the possibility of removing copper from liquid steel through the use of lead, silver, and bismuth as solvents. They also calculated that the activity coefficient of copper in liquid iron would be increased five or sixfold by addition of 4 pct C. Langenberg and Lindsay' are investigating the effectiveness of lead and sodium sulfide in removing copper from liquid iron. The experimental method was similar to that used by Chou' and Chipman and Floridis." Silver, copper, and iron were melted together, the copper distributing itself between the two layers so that at equilibrium a,.,, (in Ag) - a,.,, (inFe) and N,.,, (in Ag) yc,, (inFe) (in Ag). [21 N,.,, (inFe) Thus, from the concentration of copper in each layer and the activity coefficient of copper in liquid silver, the activity coefficient of copper in liquid iron can be calculated. The effect of an alloying element such as carbon on the activity coefficient of copper can also be determined from its effect on the distribution, provided the new element is essentially insoluble in silver. The one serious limitation of this method is the increasing mutual solubility of silver and iron in the presence of a third component. The mutual solubilities of pure iron and silver are negligible, but increase with increasing copper concentration beyond the range investigated. Ag-Cu System—The activity coefficient of copper in silver at 1600°C had to be estimated, since direct experimental data are not available. Kawakami" measured the heat of mixing of Ag-Cu alloys at 1200°C by a calorimetric technique. Scheil' calculated the heat of mixing in this system by use of the phase diagram, assuming that the solution is random and that the heat of mixing is independent of temperature. The terminal solid solution may be assumed to obey Raoult's law within the requirements

Jan 1, 1957

By A. T. Yu

On March 18, 1964, the 52,000 dwt ore carrier M/S Houn Maru called at the port of Coquimbo, Chile, on its maiden voyage to take iron ore to Japan. This marked the first time a vessel of this size ever arrived at Coquimbo, and the event promises to drastically accelerate henceforth iron ore exports from Coquimbo province. This was made possible by the use of a versatile shiploading system recently installed by Cia. Minera Santa Fe. Coquimbo has no mechanized loading facilities other than six conventional 5-ton cargo cranes. Limited space on shore further complicates the stocking problems. To make the best of what is available, a meticulously organized semi-hand-loading system has been developed through the years.

Jan 5, 1964

By H. Morgolin, M. A. Greenfield, P. A. Farrar

In attempts to correlate mechanical properties with microstructure, it is desirable to determine the effect of ß grain size. Determination of 6 grain size is not a problem where a has precipitated at ß grain boundaries. However, in alloys which have been processed to produce an equiaxed a +ß structure the ß grain size is difficult to determine because ß grain boundaries do not etch. The ß grain size can sometimes be laboriously determined by searching for grains which have some a! outlining the 6 grains. This difficulty of ß grain size determination in equiaxed a + ß alloys can be overcome by heating below the ß transus temperature for a short time and water quenching. Fig. 1 shows the starting equiaxed a + ß structure of the Ti-5.25A1-5.5V-0.9Fe-0.5Cu alloy used in this investigation, and Fig. 2 shows the microstructure of the same sample water-quenched after heating 1 min at 1675"F, which is 25°F below the 0 transus. The heavily etched microstructure consists of some equiaxed a! in a structure showing considerable amounts of transformed ß. The ß grain

Jan 1, 1969

By E. E. White

(Cleveland Meeting, October, 1912.) IN, August, 1911, I read a paper before the Lake Superior Mining Institute' on surveying and sampling diamond-drill holes. The present paper gives a more thorough description of these methods, together with a few changes and notes suggested by further experience. Since August, 1911, the methods, used constantly by the Cleveland-Cliffs Iron Co., have been developed to a higher degree of efficiency, and have given great satisfaction. Until a few years ago but little attention was paid to the determination of the actual course of drill-holes, to the accurate sampling and analysis of the material, or to the scientific location of the drill-holes. It has now been common practice for several years in many districts to test the inclination of drill-holes by etching glass tubes with hydrofluoric acid, but the direction of deviation from the vertical has not often been determined. Methods of determining the direction by means of a compass were first developed in connection with drilling in Victoria. The latest method used on the Rand in South Africa has been recently described by John I. Hoffman.2 In the same paper Mr. Hoffman describes an ingenious method of wedging-off a drill-bole so as to start new holes at several successive points. By this means a hole can be deflected in any desired direction, and the curvature can be controlled to a considerable extent, provided the rock is soft enough to permit the hole to be wedged off. Unfortunately, in the Lake Superior district, the jasper iron-formation is so hard that it is very difficult, if not impossible, to do this. I tried to deflect one hole so as to avoid drill-rods stuck in the hole, by using a 1 Proceedings of the Lake Superior Mining Institute, vol. xvi., pp. 100 to 120 (1911). 2 Recent Practice in Diamond-Drilling and Borehole Surveying, Bulletin No. 91, Institution of Mining and Metallurgy (Apr.. 11, 1912).

Nov 1, 1912

By George C. Coupland

Ecstall Mining Limited, a wholly owned subsidiary of Texas Gulf Sulphur Company, is the owner and operator of the Kidd Creek Mine including the concentrator complex located near Timmins, Ontario. Canada, approximately 450 miles north of Toronto. The mine, concentrator and Timmins form a triangular arrangement with a 17-mile rail link connecting the mine and concentrator and both of these facilities 18 and 14 miles respectively by road from Timmins. A core drilling program in the spring of 1964 established the presence of a large massive sulphide orebody which was to become the Kidd Creek Mine. Texas Gulf Sulphur had been conducting an intensive search for base metal in various parts of Northern Ontario and Quebec since 1957. Of several thousand anomalies detected in airborne electromagnetic surveys, several hundred warranted ground inspection, but only one of more than sixty drilled became a commercial orebody, the Kidd Creek Mine. The geophysical exploration work has been well covered in a paper written and presented by Van Donohoo, presently a Vice-President of T.G.S., at the American Mining Congress in San Francisco in October 1969. GEOLOGY The orebody lies within a series of overturned rhyolitic flows and pyroelastics with a major peridotite intrusive to the east. The hangingwall and footwall are composed chiefly of intermediate volcanics, andesite and dacite. The southern end of the orebody appears to terminate abruptly against greywacke while the north end is bifurcated and the structure obscured.

Jan 1, 1970

By K. E. Manchester, C. B. Sibley

The feasibility of doping silicon to produce device structres by directly implanting impurity atoms has been demonstrated. Both phosphors and boron ions have been successfully implanted in silicon to produce electrical junctions. Junctions as deep as 1.2 p have been produced by phosphorus ions having energies the order of 80 kev. An electromagnetic separator has been used to controllably produce uniform, large-area implantations for evaluation experimentation. Correlations between junclion depths and ion energies huve been obtained. Orientation effects have been observed and it has been found that the (110) direction is the easy direction for implanting. Monitoring of thermal treatments oj implanted substrates by sheet-resistance measurement indicates a very mild thermal anneal removes most of the damage done during the implantation. These indications are further substantiated by reverse-current measurements of j,inctions Produced by implantation. Electrical characteristics of implanted junctions are compared with those of diffused junctions. We have been interi n the interaction of energetic ions in the III-V groups, in particular boron and phosphorus, with single-crystal silicon to produce type conversion for possible device use. A number of investigators, a few of whom are avies, Kornelson,3 and so forth, have reported on penetration of energetic ions into both amorphous and crystalline solids. While most work has been done with ions of the rare gas and alkali metal groups, some work has been reported by ing, erber,' and others6 in which ions of the 111-V groups have been implanted in single-crystal silicon. A large amount of this work has been done with ion energies in the 100-kev to 1.5-Mev range. An excellent review article has been written by caldin. We have concentrated on ion energies which are in the 10 to 80 kev range, with which over 1500 implanted junctions such as the one shown in Fig. 1 have been produced in silicon substrates with both phosphorus and boron ions. Fig. 1 is a 3-deg angle lap in which the n type area produced by 66 kev P is delineated and the junction is 9500A below the surface. EXPERIMENTAL Implantations reported in this paper were made with the ion source adjusted to produce ion currents in the range of 1 to 2 pa with accelerating voltages varied from 10 to 40 kv. When using doubly charged ions this produced 10 to 80 kev ions. This allowed substrate temperatures to remain below 100°C. Sam- ple movement resulted in beam impingement angle variation of 7 deg from the normal to the substrate surface. Substrate resistivities have been varied through the range of 0.001 to 500 ohm-cm and specimens oriented in three directions, (110), (Ill), and (loo), within 12 deg. RESULTS For the purpose of this paper, discussion of results will be limited to phosphorus implantations with mention of results for boron-implanted silicon. Similar results have been obtained for boron and will be reported at a later date. In Figs. 2, 3, and 4 depth penetration is shown

Jan 1, 1967

By P. G. Hallof

Only recently has the term Induced Polarization found its way into geophysical literature. Schlumberger first mentioned the possible use of the induced polarization effect in one of his early papers. Later, induced polarization was the subject of several university theses, such as Seigel's at the University of Toronto and Bliel's at the Michigan School of Technology. In addition, a group at the New Mexico School of Mining and Technobgy has done work on induced polarization. There is very little to be found in print on the subject of induced polarization. Several papers have been presented at meetings, the 1958 AIME and SEG* conventions, for instance, on laboratory measurements of the effect and theoretical considerations useful in the interpretation of field results. This paper is the first attempt to present actual field results which show the usefulness of induced polarization as a prospecting technique. There are several phenomena that can cause polarization when electrical current is passed through the ground. In a paper presented at the 1958 SEG* meetings Professor T. R. Madden of M. I. T. demonstrated that only two of these gave rise to appreciable effects. The first is a result of the membrane and diffusion effects in a sandstone that contains appre- ciable amounts of clay minerals. The unbonded charges associated with the clay mineral forma material that passes positive and negative ions with different mobilities. When current is passed through such a system for some period of time, polarization results. The second phenomenon, which gives rise to very much larger polarization effects, is the one used in the new prospecting technique. These effects are a result of the blocking action or polarization of metallic or electronic conductors in a medium of ionic solution conduction. This electrochemical polarization, called "the over-voltage effect" by electro-chemists, occurs whenever electrical current is passed through a volume of rock which contains metallic minerals such as base metal sulphides. This polarization at metallic interfaces in ionic solutions depends upon the chemical energies necessary to allow the ions to continue the flow of current by giving up or receiving an electron from the metallic surfaces. The energy stored in this reaction isanalogous to that stored when a condenser is charged. If a d. c. current flowing through such a system is interrupted, the polarization can be detected as a small, decaying current that flows after the applied current is discontinued. The decaying potential measured is a result of the current flow caused by charges returning to their equilibrium positions from the positions they assumed under the applied potential field. Because of the polarization, there is an excess of change at each metallic interface. There is an alternate method of measurement of the induced polarization effect. The electrical

Jan 1, 1961

By A. W. Schlechten, R. P. Abendroth

Jan 1, 1960

By B. D. Lichter

In a previous paper, Oelsen, Schuermann, and Hey-nertl pointed out the possibility of obtaining complete thermodynamic functions for alloy systems from calorimetric measurements alone. Specifically, if the heat content of a heterogeneous, multicomponent system is known as a function of temperature and composition, then it is possible to derive the heats, entropies, and free energies of formation of liquid phases and of solid intermediate phases of fixed composition. The authors present equations and graphical techniques applicable to eutectic systems and systems with intermediate phases without solid solubility at lower temperatures. eijering has considered possible extension of the treatment to systems with complete solid-state miscibility at lower temperatures; however, experimental difficulties practically restrict the method to systems with very limited miscibility in the solid state. The purpose of this note is to present an alternative derivation of the heats and entropies of formation of liquid phases and of solid intermediate phases from heat-content measurements alone. Fig. 1 shows three types of phase diagram to which the analysis may be applied. If the heat content is determined as a function of composition x, at temperature T, we have quite generally and the heat of mixing of the liquid is obtained directly from heat-content measurements. If the temperature T lies in a two-phase region (solid-liquid) then

Jan 1, 1967

By James P. Sloss

A PERMANENT assay office is commonly established as part of the general plant equipment of operating gold and silver properties, but during the development stage of a mine, the cost of such an office is usually so assay work must be done elsewhere. In most instances only a few samples will be taken each day, but if the mine is to be developed scientifically, the analyses of those samples will guide further development. Under such circumstances, the time element in assay returns is important, since the lapse between the taking of the samples and the receipt of results may determine the success or failure of a small-mine operator. The following description of fur-

Jan 1, 1935

By AIME AIME

THE John Fritz Gold Medal for 1929 was presented to Herbert Hoover at the Executive Mansion on April 25, at a luncheon given by Mr. Hoover to present and past members of the Board of Award, preceding medalists, and presidents and secretaries of the American societies of Civil, Mining and Metallurgical, Mechanical, and Electrical Engineers. The presentation party of forty engineers which gathered at the White House, from all parts of the United States, was made up of past presidents of the four senior national engineering societies that established the John Fritz Medal and included five men who had received the medal in previous years. These former medalists were Edward Dean Adams, J. J. Carty, J. Waldo Smith, Elmer A. Sperry and Ambrose Swasey. This medal is the highest honor bestowed by these four national engineering societies, having a membership of 60,000. It is awarded not oftener than annually for "notable scientific or industrial achievement, without restriction on account of nationality or sex." In accordance with custom, the award to Mr. Hoover was made tentatively and without announcement in October, 1927, and was formally con- firmed and announced one year later.

Jan 1, 1929

By Jack G. Gill, Richard A. Dick

Blasting safety is a subject that cannot be overemphasized. Two years ago, a study was published describing g a series of fatal blasting accidents which took the lives of ten metal and nonmetal miners during the period of May 1973 to August 1974.1 Each accident was described, and the direct causes were delineated. In each instance, specific MESA safety regulations were violated. Four of the victims were killed by drilling into explosives; two were killed by lingering too long in the vicinity of fuse rounds; two fatalities resulted from improper guarding of shots; one blaster did not retreat far enough to avoid the blast concussion; and another used an improper tester for checking an electric blasting cap. All of these fatalities could have been avoided by adhering to the MESA blasting regulations contained in 30 CFR Part 55 (Health and Safety Standards-Metal and Nonmetallic Open-Pit Mines), Part 56 (Health and Safety Standards-Sand, Gravel and Crushed Stone Operations), and Part 57 (Health and Safety Standards-Metal and Nonmetallic Underground Mines).

Jan 11, 1977

By C. D. Haynes, S. C. Gambrell

The practice of roof bolting in WORLD-WIDE mining activities is very well-known, having been used extensively for over 50 years. The theory of roof bolting, however, is extremely complicated, and only recently have investigators attempted to explain the theory. Various means of stress analysis have been utilized in rock mechanics, most of which reduce rock to an isotropic, homogeneous medium that can be easily analyzed. One of the indirect research methods is the photo-elastic technique, the theory of which is widely known and needs no elaboration. This technique has been used extensively to examine the state of stress around underground openings of various shapes in certain types of strata, and under various loading configurations.'-" In-Situ Mine Roof Trusses The photoelastic technique was employed here to evaluate the state of stress above a mine opening where support is provided by the in-situ mine roof truss. This support configuration, shown in Fig. 1, has gained popularity in recent years, particularly in mines with bad roof conditions." To the authors' knowledge, no scientific determination has been made of the advantages roof trusses may offer over conventional bolting configurations comparable to roof trusses. Ordinary mine roofs usually sag or bulge downward soon after mining. Normally, after some movement the roof begins to stabilize, but the face of this bulging mine rock is usually in tension and will almost always fail unless supported. Because rock fails easily in tension, it is desirable to "preload" the roof, that is, to impress a compressive force on the mine roof to prevent bulging and subsequent tensile failure. Ordinary rock bolting installations, particularly if the bolting is perpendicular to the mine roof plane, do not produce a preloading effect. Although bolting installations squeeze the strata together and produce a beam effect desirable for support, they do not have the advantage of actual uplift. They pull down at the anchorage point with a force equal to the bolt tension which sometimes causes a separation in the plane of the anchorage detrimental to roof strength. In-situ mine roof trusses require the installation of steel tension rods in the roof of the mine much the same as conventional roof bolts, except that the rods are arranged to produce a stress pattern above the upper surface of the opening similar to that of a prestressed beam. The roof rock acts to transmit the compression force. The simplest form of truss consists of two steel rods anchored to the back of holes drilled at an angle of approximately 45 over the mine pillars. These rods are collared near the middle of the room, and the lower ends of the rods are connected by tie rods and turn-buckles. Used in this manner, a small-diameter steel rod can provide essentially the same support as a wide-flange steel beam. By tightening the turnbuckles, an uplift on the roof can be produced. Objective of the Investigation The objective of this investigation was to determine qualitatively the state of stress that exists above a mine roof after the installation of the in-situ mine roof truss vs. that of two angle roof bolts, hereafter referred to as "roof bolts," drilled and placed in the same configuration, that is, 45" above each pillar and connected together in the middle of the room by a bearing member such as a steel beam. Each state of stress was to be identified, insofar as possible, as compression or tension above the mine opening. Model Construction A photoelastic model of a mine opening was coil-structed from -in. thick PLM-4B birefringent plastic and was machined to specification shown in Fig. 2. The dimensions of the opening were chosen to simulate a width-to-depth ratio of 3 to 1. Two % -in. holes were drilled at 45" angles, as shown, to provide for the loading devices. After construction, the model was annealed at 240°F to remove stresses produced during machining.

Jan 1, 1971