Search Documents

By I. J. Demer, M. L. Holzworth, J. C. Kremer, P. A. Beck

For alloys which are in practice heat treated to obtain increased strength, such as steels, duralumin, copper-beryllium, and others, the treatment usually involves heating to a relatively high temperature. At such temperatures the grain size of the product is largely determined by grain growth. Even in metals and alloys annealed merely to relieve work hardening, recrystal-lization is generally followed by a certain amount of grain growth. Thus, effective grain size control, which is often of great practical importance in manufacturing processes, depends on the grain growth behavior of the material used. Despite its importance, grain growth has been the subject of few investigations of a fundamental nature. The term "grain growth" has been used to designate a group of related, but distinctly different, phenomena. The two most important and best known of this group are illustrated by the following example. Curve a in Fig I shows the increase of the average grain size of a copper-beryllium alloy, containing 2 pct Be and 0.15 pct Co, with increasing annealing temperature. The time of annealing was 2 hr. The grain size was quite uniform in all specimens. The results of a similar experiment with an alloy containing 2 pct Be and 0.31 pct Co are shown by curve b It is seen that for any annealing temperature below T, the grain size was smaller than. in the previous case. Grain growth became slower with the higher Co content. This "inhibiting" effect of the higher Co addition was associated with the appearance in the microstructure of fine, light blue particles of the CoBe phase. Up to temperature T, the structure of the inhibited alloy (curve b) was just as uniform as the structures represented by curve a. However, after annealing at T or at higher temperatures, the inhibited alloy showed some extremely large grains (much larger than the grain sizes developed by the uninhibited alloy with low Co content) mixed with the small grains according to curve b. The presence of these mixed or "duplex" structures is indicated in Fig I by the vertical lines branching off curve b. The type of grain growth occurring in uninhibited Cu-Be alloys (curve a) has been most frequently and best investigated in brass. This type has been designated as "normal grain growth,'' while the grain growth phenomena occurring in inhibited materials were, at times, referred to as "abnormal grain growth." However, since the latter term has been applied occasionally to the phenomenon of critical recrystallization, which also results in large grains although by an entirely different mechanism, in the present paper a different nomenclature has been adopted in order to avoid confusion. Typical of the grain growth in uninhibited metals and alloys is the continuous

Jan 1, 1949

INTRODUCTION The regional characteristics of porphyry copper deposits in South America southward from Pantanos and Pegadorcito, Columbia, will be summarized. The age of formation of deposits spans the period from the Permian to the present. Where possible, the general characteristics and the individual structural features of the deposits are integrated into the plate tectonic model. Individual deposits cited in this chapter, located in Fig. 1, are the best known and most fully described, and form the Andean copper belt (Peterson, 1958). Smaller porphyry copper deposits fall both east and west of the line of large, high grade deposits (e.g., Chuquicamata and Toquepala) that make up the spine of this belt. Most of those smaller deposits (e.g., Mi Vida [Koukharsky and Mirre, 19761) are omitted from Fig. 1 and Tables 1 and 2, however. Neither the Andean orogen nor the individual deposits within it are as well de- scribed in the literature as are their counter- parts in the Cordilleran orogen of North America. Therefore, generalizations relying on regional geologic mapping, geophysics, and isotopic geochemistry lack details pertinent to this type of deposit in the Cordilleran orogen. The South American porphyry copper province has been described by Hollister ( 1974) to include most of the Andean orogen excepting the tin province of Bolivia. Porphyry copper deposits have not been commonly found within the tin belt, although copper-tin (e.g., San Rafael, Peru) and copper-tungsten (e.g., Llamuco, Chile) de- posits are known. James (1971) shows the depth to the Moho to be appreciably greater where the tin belt exists, but disclaims any genetic significance from the coincident appearance of the tin-tungsten province and the inhibition of porphyry copper development where the sialic crust thickens. Dates on tin mineralization in this belt (Clark and Farrar, 1973) are similar to some dates for porphyry copper mineralization known else- where in the Andean orogen. It seems that some mechanism is needed to explain the geographic separation of porphyry copper- molybdenum and simultaneous tin-tungsten- molybdenum metallization within the same tectonic system and appearing at similar distances from the trench. The thickened crust of the tin belt is one of the few known differences. Tables 1 and 2 list some of the most important porphyry copper deposits explored to date, but do not include Antaminas, Peru. or a number of other large skarn deposits

Jan 1, 1978

By Robert L. Dean

THE pioneer mining company in Idaho to use airplanes extensively is the Yellow Pine project at Stibnite now owned by the Bradley interests. From 1901 to 1903 the gold boom at Thunder Mountain, in central Idaho overflowed to adjacent areas, prospectors discovering cinnabar and stibnite near the present site of Stibnite in Valley County. The workings were practically abandoned by 1911 through lack of capital and high costs of transportation on pack train roads over several mountain passes open only five months each year. During the World War there was some prospecting and production, and in 1921 twelve of the original companies were merged. Small-scale mining up to 1927 proved that an expenditure of several million dollars would be necessary to operate profitably. These properties were purchased by the Bradley interests during the period of 1927 to 1930. In 1927, there was no mining equipment except hand tools, no telephones, and only one building. Two mountain

Jan 1, 1935

By Lawrence Addicks

ONE of the properties of copper, which has done much to give it its present prominent place among the useful metals, is its electrical conductivity, a property which has now become the chief criterion of 'the value of the commerical product. In pursuance of that distinctively American principle that, 1' the best is none too good," metal of the highest conductivity is usually called for even where such extreme purity is of no advantage, for instance, in the making of brass and other alloys. The average brass-founder feels nervous unless his copper is so very pure that it shows a conductivity of 99 or 100 per cent., while the character of the zinc used is usually overlooked in his anxiety. Electrolytic refining has made it possible to produce copper of a' very high degree of purity, the metallic impurities averaging but a few thousandths of 1 per cent.; oxygen, usually present in the form of cuprous oxide, bringing the total up to about a tenth of 1 per cent. The published data bearing upon the relationship between chemical purity and electrical conductivity is, however, very scant,' nearly all the work that has been done having dealt with alloys carrying considerable quantities of the foreign elements. In this paper I have brought together the results of experiments extending over a period of several years that have been carried out with the idea of determining the amount of various elements which would lower the conductivity 3 or 4 per cent.-a series of impure coppers rather than alloys. There are many precautions necessary to keep the conditions

Mar 1, 1905

By Charles B. Henderson

DESPITE the loss, by enemy conquest, of a high percentage of our normal sources of supply for tin, the position of this important metal is easier today than that of rubber and a long list of other strategic materials, many of which are produced in this country. Actually, there is no shortage of tin for essential war purposes, owing to a strict control of its use, to increasing considerably the amount of secondary tin available, and to the foresight of the Government in authorizing the Reconstruction Finance Corp., as early as June, 1940, to acquire and produce certain critical and strategic materials of which tin was one of the most important. The construction of the Longhorn Smelter on the Gulf Coast in Texas is an important part of this program.

Jan 1, 1943

By G. R. Speich

The interlarnmelm spacing, growth rate, and degree of segregation that accompany cellular precipitation in four Fe-Zn alloys containing 9.7, 15.2, 23.5, and 30.5 at. pct Zn have been determined in the temperature range 400" to 600°C. The chemical free-energy change for the reaction was calculated from the available thermodynamic data and the known compositions of the phases. The fraction of the chemical free-energy change for equilibrium segregation that is converted into interfacial free energy decreases from 0.43 to 0.08 as the magnitude of this free-energy change increases from 35 to 270 cal per mole. At constant temperature the cellular growth rate is proportional to the cube of the dissipated free energy. At 600°C newly 100 pct of the equilibrium segregation is achieved during cellulm precipitation whereas at 400°C only 85 pct of the equilibrium segregation is attained. During cellular growth, mass transport of zinc occurs by grain boundary diffusion; excess zinc remaining in the a! phase after the completion of growth is removed slowly by volume diffusion. A modified Cahn theory of cellular precipitation predicts the observed interlamellar spacing within a factor of two. In cellular precipitation reactions such as pearlite formation or discontinuous precipitation, the basic problem is to predict the variation of growth rate G, interlamellar spacing S, and degree of segregation P with composition and temperature. To accomplish this we need three independent equations relating these quantities. One of these equations comes from the diffusion solution. To obtain two additional independent equations, some assumptions must be made. cahnl has suggested recently that two plausible assumptions are 1) that growth rate is proportional to the dissipated free energy and 2) that the spacing which occurs is that which maximizes the dissipated free energy. According to the first assumption, this spacing also maximizes the growth rate and the rate of decrease of free energy per unit area of cell boundary. The present work was undertaken to test these assumptions. To test the first assumption it is necessary to study a cellular reaction over a wide range of supersatura-tions to establish a relationship between G and the dissipated free energy at constant temperature. This is possible only in discontinuous precipitation reactions since in pearlite reactions constituents other than pearlite form if the composition of the parent phase deviates even slightly from the eutectoid composition. The Fe-Zn system was chosen for study because 1) discontinuous precipitation proceeds to completion over a wide temperature and concentration range, 2) the degree of segregation within the cell can be measured by lattice parameter measurements,2 and 3) the thermodynamics of this system have recently been determined by Wriedt.3 In this system the cells consisting d alternate lamellae of a and r phases form from supercooled iron-rich a phase. The a phase within the cells is bcc as is the original a phase, cia, but has a different orientation and a slightly lower zinc content than the original a phase. The r phase has a zinc content of about 70 at. pct and a crystal structure isomor-phous with T brass. EXPERIMENTAL PROCEDURE Four Fe-Zn alloys with 9.7, 15.2, 23.5, and 30.5 at. pct Zn were prepared from carbonyl-iron powder (400 mesh, 99.8 wt pct Fe) and zinc powder (200 mesh, 99.99 wt pct Zn). The powders were ball-milled together and cold-pressed under 60,000 psi to discs $ in. thick by $ in. diam. The cold-pressed discs of the alloys with 9.7 and 15.2 at. pct Zn were sealed in evacuated silica capsules and heated slowly to 1100°C over a period of 1 week (3 days at 600°C, then 3 days at 80O°C, then 1 day at 1100°C). The alloys with 23.5 and 30.5 at. pct Zn were treated similarly except that the final homogenization temperatures were 1000" and 85O°C, respectively, to prevent melting. The alloys were quenched in iced brine from the final homogenization temperature. Specimens of each alloy were subsequently aged in salt pots at temperatures of 400°, 450°, 500°, 550°, 600°, and 650°C for times that varied from a few minutes to several hundred hours. At a late stage of this work, an alloy containing 11.2 at. pct Zn was prepared by vapor-impregnation of iron foil with zinc vapor at 890°C. This alloy proved useful for electron microscope studies because it was free of porosity. The homogenization and aging conditions were based on the recent Fe-Zn phase diagram of Stadelmaier and Bridgers4 rather than the earlier diagram of ansen.5 They consist of a homogenization heat treatment in the homogeneous a field followed by an aging treatment in the two-phase a + r field. The aged specimens were metallographically polished and etched in 2 pct nital and the radius of the largest cell in the microstructure determined. This radius plotted vs time gave a straight line whose slope is the boundary migration rate or growth rate G of the cell. To determine the interlamellar spacing, specimens were examined by surface-replica and thin-section electron microscope techniques. Because of the irregular nature of the lamellae within the cell, the average interlamellar spacing S .of the cell was measured by the method of Cahn and Hagel,6 where S is defined by:

Jan 1, 1969

By Benjamin C. Koskiniemi

Introduction When evaluating any ore body, one of the first questions concerns the ore reserves. In the case of an open pit mine, this is not possible to answer reliably until the ultimate (final) pit limits have been established. Techniques used in designing an ultimate pit are classed as (1) manual, (2) computer, and (3) combined manual-computer. This chapter will describe how manual techniques can be utilized in designing an ulti¬mate pit Certain economic and design criteria must be established before the actual design begins In order to begin designing an ultimate pit, it will be assumed that the engineer already has the following data available (1) vertical sections, (2) horizontal sections for each level, (3) stripping curve, (4) bench height, (5) bank slope angle between levels, (6) level berm width, (7) roadway width, (8) pit slope angles at ultimate pit limits (estimated average including roads and ramps and between roads and ramps), and (9) minimum width of pit bottom

Jan 1, 1979

By R. E. Cuthbertson

AN early appreciation by the management that Climax ore presented a challenging problem of economic concentration was responsible for the establishment, in June 1926, of an ore-testing department at the experimental plant of the Colorado School of Mines at Golden, some ninety miles from Climax. An engineering office was later organized in the same community for the design of all ore-treatment units erected at Climax during the period of rapid growth. Work of the ore-testing and design staffs was effectively co-ordinated under a common head. The primary reason for having the ore-testing and plant design departments in Golden, was to place these activities under the able supervision of A. J. Weinig, consultant for the Climax Molybdenum Co., and director of the experimental plant. A secondary consideration was the availability of excellent facilities for research in ore dressing in a highly favorable environment. Concentration of molybdenite by flotation from an ore of simple mineral composition does not appear, superficially, to present a serious problem in ore dressing but experience belies this apparent simplicity. The molybdenite content of average Climax ore is low and it is finely

Jan 1, 1946

By A. Keith Brewer

RECENT advances in the fields of chemistry, biology, and metallurgy have confronted the analytical chemist with an entirely new set of problems. Development of plastics and synthetics has brought about a need, not only for adequate methods for their analysis but also for the various raw materials entering into their manufacture. The remarkable advance made in biochemical and agricultural research resulting from the use of isotopes as tracers or "tagged atoms" has established the necessity for the development of methods for the concentration of natural isotopes and for a means for their analysis. Similarly the advent of new and complex alloys calls for accurate analytical methods. Fortunately the analytical chemist has been able to meet some of these new demands by adapting to his purposes an instrument which has long been the most exclusive toy of the physicists. Solubility and the chemical properties of the atoms, which have always served as the basis for chemical analysis, do not enter into this new technique. Instead, momentum, defined as mass times velocity, is utilized as the means for the separation of atoms or mass groups.

Jan 1, 1946

By R. Chanchani

Single and mixed mineral flotation behavior and the mechanisms for the loss of selectivity in 1:1 and 95:5 apatite: dolomite mineral mixtures are presented. Loss of selectivity in mixed mineral systems is attributed to depletion of oleate ions available for adsorption by bulk precipitation with calcium and magnesium ions dissolved from dolomite. Flotation after two-stage conditioning was found to be a potential technique to separate dolomite from apatite. This method involves conditioning at pH 10 followed by reconditioning at a lower pH. The results indicate that selective flotation of dolomite, a minor mineral in south Florida phosphate deposits, could be obtained by reconditioning at pH below 4.5. Higher selectivity was observed for mixed minerals as compared to that of single minerals.

Jan 1, 1986

By T. Egleston

The importance of making analyses of gases in furnaces which are used for metallurgical purposes is every day growing more and more evident. It is the only method of understanding the reactions that take place in the furnace, and of economically conducting the operations both with regard to the fuel used and the reactions which take place on the bodies to be subjected to the influence of the heat and gases. As a knowledge of the composition of gases is becoming every day more necessary to the proper conduct of furnace operations, it seems desirable that furnace managers should generally know that the analysis of gas for commercial purposes is neither difficult, tedious, or expensive, and that it does not necessarily imply the use of corrections requiring difficult instrumental observations and long and tedious mathematical calculations. Any method, therefore, which will tend to render these analyses simple will also tend to having them made and repeated as frequently as the analyses of the ores and other materials charged in the furnace. They should be made even more frequently, as their composition is affected by any change in the condition of the furnace, and a knowledge of their composition will give a ready clue to the unseen and otherwise not easily detected changes which are taking place. The only practicable method of making industrial analyses of gas is that of measuring volumes in graduated tubes. The methods by

By T. PH. D. Egleston

THE importance of making analyses of gases in furnaces which are used for metallurgical purposes is every day growing more and more evident. It is the only method of understanding the reactions that take place in the furnace, and of economically conducting the operations both with regard to the fuel used and the reactions which take place on the bodies to be subjected to the influence of the heat and gases. As a knowledge of the composition of gases is becoming every day more necessary to the proper conduct of furnace operations, it seems desirable that furnace managers should generally know that the analysis of gas for commercial purposes is neither difficult, tedious, or expensive, and that it does not necessarily imply the use of corrections requiring difficult instrumental observations and long and tedious mathematical calculations. Any method, therefore, which will tend to render these analyses simple will also tend to having them made and repeated as frequently as the analyses of the ores and other materials charged in the furnace. They should be made even more frequently, as their composition is affected by any change in the condition of the furnace, and a knowledge of their composition will give a ready clue to the unseen and otherwise not easily detected changes which are taking place. The only practicable method of making industrial analyses of gas is that of measuring volumes in graduated tubes. The methods by

Jan 1, 1877

By E. A. Holbrook

IT may be taken for granted that a mine official knows his duties, as outlined by the bituminous mining laws of the State, he knows how coal should be mined and transported, and he has judgment on any possibly unsafe condition in his mine. Certainly, if he is weak on any of these points, there are definite ways in which he can acquire the needed knowledge. If with this knowledge the mine official has the necessary practical experience to bring self-confidence, he stands before the world as a man who knows his job. There is, however, another side to his work, one not found in hooks, a side even that may not be learned at the face even though one spends a lifetime there. The actual duties a mine official knows and performs are the tangible and definite things about his work. There are other things which may be termed intangible, because they are hard to pin down and see, and. which appear to be of equal importance in successfully handling a job and which in time determine the very success of the company itself.

Jan 1, 1930

By A. K. Chakravarti, A. Lihiri, G. G. Sarkar

One primary objective of India's third Five Year Plan is the expansion of coal production. The goal: boost present output of 45 million tons to 95 million tons by 1965--an increase of more than 100 pct!

Jan 7, 1961

By George S. Rice

MECHANIZATION in coal mining is a phrase which has attracted world-wide attention, and those persons not engaged on the practical side of coal-mine operations seem to regard mechanization as a panacea for many difficulties of the industry. The term "mechanization" as now employed by experienced mining men is restricted to mean mechanical loading of coal at the face. In a broader sense mechanization in coal mining was begun nearly half a century ago with the introduction of compressed-air undercutting machines and locomotives and, later, of electrically operated locomotives, undercutting and shearing machines, and drills. The use of coal-cutting machines, which has increased until now about three- fourths of the bituminous coal produced is being mechanically cut, first displaced hand-picking except in a few long-wall mines, and later gradually displaced the dangerous and coal-smashing method of blasting-off- the-solid.

Jan 1, 1929

By M. Kashiwada

The zinc leach residues are introduced into waelz kiln to fume volatile metals and before the end of 1967, the waelz-fume containing zinc, lead, cadmium and indium was directly recycled back to the leaching process for the production of electrolytic slab zinc. However, since 1968, we have been recovering with success those valuable metals contained in the fume separately instead of direct leaching. According to the improved process, the waelz-fume, after being mixed with chloridizing agents, is fed into the rotary kiln to be roasted, wherein most of lead and cadmium content is collected as fume and most of zinc remains in the calcine. Zinc calcine thus obtained, containing 70 to 75 per cent zinc and, less than 1.0 per cent lead is sent to zinc plant for further recovery and the fume containing 40 to 50 per cent lead and 3 to 6 per cent cadmium is further processed to recover lead, cadmium and indium. The advantage of this process can be secured to the utmost when it is combined with the following subsequent treatments. (a) Blast furnace smelting of non-magnetic waelz slag to recover copper, silver and gold as matte. (b) Gallium recovering process from magnetic waelz slag. (c) Soda process of lead bearing cake produced after removing cadmium and indium from the said fume. Thus the extractions of zinc, lead and cadmium from leach residues account for 87 per cent, 72 per cent and 85 per cent respectively.

Jan 1, 1970

By Louis L. Stott

It is well known that the oxide of beryllium was identified as a new "earth" in 17971 and the metal first isolated in 18272. The history of the many difficulties encountered by early investigators, the laboratory achievements of Lebeau3, Fichter4 and Oesterheld5, and the eventual development of methods for commercial production are well covered in the literature, particularly in the authoritative published work of Siemens and Halskes reviewing their comprehensive investigation of the element. Accordingly it has seemed desirable to restrict this paper to the properties and uses of beryllium and its alloys. PRopeRties of Beryllium A comprehensive summary of the available data on the properties of beryllium is given in " Gmelius Handbuch der Anorganischen Chemie7." The metal is steel gray in color. A fractured surface exhibits a bright luster, which does not appear to change with long exposure to air, probably because of a thin, transparent protective oxide coating. The specific gravity is approximately 1.8. Although there is no recorded actual determination of Young's modulus of elasticity, it has been estimateds, according to Fessenden's law, to be 30,000 kg. per sq. mm., or about 30 per cent higher than steel. Beryllium appears to have an electrical conductivity approximately 1/12 that of copper. The physical constants as available in the literature are given in Table 1. One of the outstanding properties of beryllium is its great affinity for oxygen, nitrogen, sulfur and carbon. One gram of beryllium takes up 1.774 grams of oxygen and will liberate approximately 15.23 kilogram-calories in the combination. The metal apparently reacts with all known oxides at high temperatures; in fact, beryllium will alloy with thorium and zirconium if melted in crucibles of their oxides. The true physical properties of beryllium are still somewhat in doubt, since very small amounts of impurities appear to cause a large variation

Jan 1, 1936

By H. H. Uhlig

IN our study of the mechanism of and the prevention of corrosion in stainless steels, it was considered of fundamental importance to obtain knowledge of the surface structure of such alloys. If corrosion resistance is due to a self-healing oxide layer, which like a paint film protects the underlying metal, it would be obviously relevant were the effort made to make the film less permeable and more adherent; for example, the surface might be expected to respond to an anodizing process, which is found successful in increasing the film thickness and corrosion resistance of aluminum. However, if passivity and corrosion resistance of stainless steels are due to another cause, the attack of the problem would follow another path. One of the most effective techniques for studying passivity and corrosion tendency is the measurement of the electrochemical potential. Not only can one determine by potential measurements whether a metal is active or passive, but also one can determine the degree of passivity and rate of transformation of passivity with time. Chemical media that build up or destroy passivity when in contact with the steel can also be classified by potential measurements. Something can be learned, too, of the effect of alloy additions such as molybdenum to 18-8, known to decrease corrosion of the alloy in chloride solutions. A study of alloys in previous investigations has sometimes included data on the electrochemical potentials. Tammann and Sotter1 measured the electrochemical potentials of alloys of iron-molybdenum and iron-chromium and reported the critical concentration of molybdenum or chromium at which passivity initiates. Strauss2 made similar measure-ments for the iron-chromium system. The electrochemical potential' has also been used to indicate carbide precipitated 18-8. In 18-8, heat-treated to precipitate carbide, active metal exists at the region of the grain boundaries, contrasted with passive metal within the grains, the active metal accounting for a resultant active potential. Several

Jan 1, 1939

By C. A. Stetefeldt

The iron-ore deposits worked by this Company occur in lenses 200 to 1000 feet long and 5 to 80 feet wide, and stand at an angle of from 65' to 75, with a vertical height of 250 to 500 feet, other lenses occurring below. A number of the deposits were first worked as open pits, which in some cases were carried to the depth of 150 feet, when, owing to the weakness of the walls, underground mining was adopted. While the ore was being removed from the open pit, shafts mere in several instances sunk into the foot-wall, the intention being to mine the ore with breast-stopes of an approximate height of 20 feet, followed by underhand-stopes of the same height, leaving floors between of the necessary thickness to support the walls, or to effect the removal of the ore by means of what is known as the stall system. As the work progressed, however, it was found that the walls (which are of chlorite) were too weak to permit the working of breast-stopes 20 feet high, there being frequent heavy falls of ground from the hanging and, in some instances, from the foot. The plan of following breast-stopes with underhand-stopes was, therefore, abandoned. By working breast-stopes only, but little more than one-half of the ore could be removed, and that only at an excessive cost, the ore being so hard that power-drills with 3 1/8-inch pistons . and 6-inch stroke, working under 60 pounds of compressed air, are able to drill but 8 feet in ten hours as a yearly average, while from 6 inches to 2 feet is a common result of ten hours' drilling. It was plain that some other system of mining must be adopted, and it was proposed to sink by levels of 75 feet, carrying in the cross-cuts from the shafts and working out the ore each way from the shaft from foot to hanging, and from 15 to 20 feet in height. When this has been done, drift-sets consisting of caps and legs are set up the whole length of the opening and connected with the cross-cut; the necessary openings for ladder-ways and chutes or mills are timbered from

Jan 1, 1893

By W. O. Philbrook, A. H. Jolly, T. R. Henry

In the course of a study of slag-control methods, the authors devised a laboratory technique by which the basicity of basic open-hearth furnace slags could be estimated with sufficient accuracy to make the method of possible interest for slag-control purposes. The process consisted of measuring the slight basicity of an extract of the powdered slag in water. The procedure was presented, for the benefit of those who might care to experiment with it, in a paper submitted in the 1944 McKune Award Contest and presented at the 1944 Open-hearth Conference in Pittsburgh.' Interest expressed at that meeting and favorable operating experience with the method at a neighboring plant, as described in a related paper by Michael Tenenbaum and C. C. Brown,; have encouraged us to present further details of the development, technique, and pitfalls of the method and some additional data not included in our first report. At the outset it must be admitted that this method of estimation of slag basicity is not perfect; neither is any other that we know of. It is subject to somewhat greater errors than would be desirable, but compares favorably with other techniques in this respect. It has the disadvantage that it places the final determination of slag basicity in the hands of a laboratory technician rather than the furnace oper- ator, although it can be operated in a control laboratory adjacent to the furnaces. It requires close attention to certain details, as do most laboratory procedures. On the favorable side, it eliminates the "human factor" of personal judgment inherent in estimation from pancakes or powdered samples. The procedure can be placed in practice much more rapidly and presents much less of a training problem than visual methods of estimation. The principle and operation of the method are so simple that it would not be surprising if others have experimented with the same or similar procedures, but we are not aware of any prior publication of details. Our own shop has been operating fairly successfully for several years with the aid of slag pancakes. Since the past year or two have not been favorable for the expenditure of time and energy where the need was not urgent, we have not introduced the new practice for actual slag control and hence do not have extensive operating data. In presenting this method, therefore, we make no claims as to theoretical justification nor guarantees as to practical applicability, but offer it as an empirical observation. We believe it has sufficient merit to warrant its investigation by those just instituting a slag-control program or in search of supplementary methods for judging slag basicity Principle of the Method It is well known that when burnt lime or slaked lime is shaken up with water it

Jan 1, 1945