Search Documents

By G. Derge

The chemical and physical propertties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use. These processes are carried out at high temperatures and involve such complex chemical systems that funda-mental scientific knowledge of the Properties and behavior of these slags is inadequate. Various hypotheses have been Proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenckl and the recent Papers of Chipman and co-authors. Another proposal is that these compounds dissociate by com-plete6 or partial ionization, the evidence for which has been reviewed by Martin and Derge.? whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: 1. Studies of solidified 51% samples by X ray diffraction, petrography, and similar methods that can be used at room temperature. The correlation of this information with the high-temperature properties of the molten slag is uncertain. 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature. However, even these data present problems of interpretation because they require a complete knowledge of the metal phase. 3. Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret. Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information. The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems cao-sio2 and cao-120,-SiO2 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1948

By A. R. Jr. Amos

LOG washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate com-pletely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5° to 10° and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1936

By Thos Gibson

THE object of taxation is the raising of a revenue. Unless a tax accomplishes this, it is a failure. The right to take for public purposes a part of the moneys obtained from the carrying on of private enterprises is an attribute possessed only by a lawful government, and may indeed he called the supreme attribute of government. In free, democratic communities this power must of necessity rest upon the consent of the governed. Power implies obligation, hence it is obviously the duty of a government, in framing a system of taxation, to provide one which, while effective in producing a revenue, is also just and impartial. It will be conceded that mines and mining property ought to bear a fair share of the public expenditure. The question is, upon what basis taxation should proceed. Two separate taxing principles are usually contended for: Taxation should be proportionate to the benefits received by the person or property taxed; taxation should be based on ability to pay. A third is sometimes added, taxation should have reference to the extent and value of the natural resources enjoyed. As applied to mining taxation, it is pointed out by those who support the first mentioned basis that, mines being usually situated in rocky and hence sparsely peopled regions, mining companies are frequently obliged to construct roads, railways, telegraph and telephone lines, schools, water and sewerage systems, and many other amenities and conveniences of civilization, the cost of which in regions better suited for agriculture and consequently more thickly populated, has either been defrayed locally, or can be spread over a sufficiently large taxable group of people to materially lighten the financial burden on the mine. The mining com¬pany, it is argued, having made these outlays, should receive credit for, them and be relieved of taxation to a corresponding extent. There may be some force in this contention, but the situation is capable of relief without attempting to place taxation upon so unworkable a basis as the value of benefits received. Who is to be the judge of these benefits, and how are they to be valued? The very existence of a mining company and its ability to carry on business in peace and security, depend on the prevalence of law and order, which is a result of good government. The state provides protection against violence, and courts of law for

Jan 4, 1919

By Gerald Edmunds

THE liquidus line on the phase diagram for temperature versus composition of a binary alloy system, representing the boundary between the homogeneous melt and the heterogeneous melt plus solid, besides showing the minimum casting temperature, is useful in determining eutectic compositions and the presence of phase changes such as peritectic transformations and intermetallic compound formation. The liquidus often is determined by the cooling curves of thermal analysis, but supercooling frequently occurs, so that the temperature values are low. An alternative method, the one employed here, consists of determining the com- position of samples of the melts from heterogeneous alloys that are at equilibrium. With meticulous attention to fundamentals, this method is capable of yielding values limited in precision only by the temperature control and measurement and analyses. APPARATUS By starting, on the one hand, with a supersaturated solution and allowing the excess solute to precipitate, and on the other hand with an undersaturated solution and allowing more of the solute to be dissolved, both processes being carried out at the same temperature, equilibrium may be said to have been approached from both directions; that is, from above and from below. If the analyses show the solutions to contain the same fraction of solute when equilibrium has been approached from above and from below, one is assured that equilibrium has been reached in both determinations. In order to carry out such determinations, it is necessary to have equipment for obtaining and maintaining the proper temperatures; for holding the melt, measuring its temperature, and stirring, sampling and analyzing it. The present work required temperatures from 420° to 900°C. The equipment consisted of: A furnace, which was a vertical alundum tube, 1 ¾ in. diameter inside and 18 in. long, wound with Nichrome resistance wire, surrounded by a 3-in. i.d. alundum tube wound for 5 in. of length near each end, for compensation of end losses. This muffle was contained in an iron shell with Transite end plates, the intervening space being packed with Sil-O-Cel. The outside dimensions of the furnace were 12 in. in diameter by 18 ½ in. in height. Heating current was supplied by three independent variable-voltage transformers (Variac), one connected to each end compensator winding and manually controlled, and one connected to the main winding through a series resistance of 5 ohms. This resistance was short-circuited for

Jan 1, 1944

By Donald Barton

THIS paper outlines a time-saving graphical method of calculation for application to the interpretation of observations with the Eötvös torsion balance. Preliminary to the treatment of this short cut method which has been found practicable, the principal formu-las by which the student of interpretation can calculate the gradient and differential curvature produced by different types of bodies in different types of situa-tions are presented and discussed. It is necessary to split most geologic bodies into a series of simpler ones for which not too complicated formulas are avail-able. The gradient and differential curvature effects are calculated for each of the simple bodies and then summed to the total effect for the whole body. The calculations are considerable in number and, though more tedious than difficult, should be' entrusted to an experienced calculator. Considerable facility in qualitative interpretation can be acquired by the geophysicist from experience and from a thorough study of the types of gradient and differential curvature anomalies produced by the dif-ferent types of possible structural situations. How-ever, semi-quantitative calculations' of the probable structure bring out many relations that are not evident in a simple inspection of torsion balance results ; it throws out as impossible or improbable certain of the alternative structural possibilities that may seem equally probable under simple inspection of the results; it will determine more accurately the position of the crest of the structure; and reduce considerably the un-certainty in the interpretation and it is necessary to intelligent interpretations. The calculation of such cross-sections consists of a trial-and-error calculation of a body that will give gradient and differential curvature effects as closely as possible the same as those observed. From his knowledge of the gradient and differential curvature produced by different types of bodies, the geophysicist sketches a tentative cross-section of the structure as indicated-to him-by the observed results of the torsion balance survey, and the calculator then splits the struc-ture into blocks, and calculates the gradient and differ-ential curvature block by block. If, as rather usual, the calculated .gradient and differential curvature pro-files diverge considerably from, the respective observed ones, it is necessary to add and subtract blocks from the cross-section until a close agreement is obtained .between the calculated and observed profiles. The com-plete calculations have to be gone through for each block that is added or subtracted.

Jan 9, 1928

By Albert Hoskinson

PROGRESS on the earth depends to a large extent upon the rapid inter-change of ideas and commodities between the various nations of the world. The smooth flow of commerce, by which these ideas and com-modities move, is accelerated by accurate and complete maps of the various land and water areas of the earth, The production of accurate maps depends upon a complete knowledge of the figure and dimensions of the object to be charted, therefore a knowledge of the shape of the earth is a prime necessity for accurate charting purposes. Gravity observa-tions were first undertaken to aid in determining the shape of the earth so that the geodetic surveys of its land and water areas might be more accurately connected to form an undistorted map. A large part of the earth's surface is water and it is therefore necessary to get gravity values at sea as well as on land before a complete and accurate figure of the earth can be determined. Dr. F. A. Vening Meinesz, of Holland, was the first scientist to perfect a pendulum instrument that would accurately measure gravity at sea. He had previously developed a multiple pendulum apparatus for measur-ing gravity upon swampy and unstable land areas in Holland and it was therefore quite natural that he should adapt the instrument to give accurate results upon a still more unstable support, the surface of the sea. His instrument as perfected gives satisfactory results when mounted in gimbals on any vessel where the roll and pitch are not more than about 5° and where the vibrations from rotating machinery and wave action are not large enough to cause the pendulums to shift on the knife-edges. This degree of stability can be obtained on surface craft only in protected waters or on very calm days. Therefore, Dr. Meinesz mounted his instrument in a. submarine so that he could submerge below the disturbed surface waters and get the desired stability in nearly any kind of weather by simply diving to greater depths. Most of the gravity-at-sea work has been done with a Meinesz instrument and a very large number of the observations have been made by Dr. Meinesz himself. He has occupied nearly 1000 sea stations and probably has traveled as many miles by

Jan 1, 1938

By J. R. Long, T. R. Graham, R. S. Dean

FOLLOWING the development of elec¬trolytic manganese production by the Bureau of Mines, an extensive program was planned to study the character of this high-purity product and its possible utilization in various alloy combinations. Previous work reported in the literature concerning alloys containing substantial amounts of manganese dealt largely with material prepared from relatively impure grades of the metal, and in many instances the impurities thus introduced did not permit true evaluation of manganese as an alloying element. One phase of the Bureau's program included a general review of the system and the establishment of the physical properties of copper-manganese-zinc alloys, using electrolytic manganese, and with particular emphasis directed to com¬positions within the alpha solid solution area. A number of reports of the work on alloys in this system, giving specific data concerning the equilibrium system and some of its alloys, have already been published. One study1 established the alpha solid solution area at various temperature levels and composition ranges up to 50 pct manganese. Other investigation reports presented the properties of selected alloys; namely, a 65 pct copper, 10 pct manganese, 25 pct zinc alloys' a sensibly white manganese brass composed of 70 pct copper, 20 pct manganese, 10 pct zinc,3 and a series of alloys with a constant copper content of 60 pct and 5 to 25 pct manganese, balance zinc.4 In these reports tensile properties as influenced by cold-working and subsequent annealing were given in detail. Additional data are now available on other alloys of the alpha region up to 50 pct manganese, and these, together with previously published information, are sufficiently complete to establish the relationship between properties and composition for this portion of the ternary system. The present report is a summary of the tensile properties of wrought alloys in the form of sheet and rod stock. The summary is necessarily limited to data for only one condition of cold-work and a single annealing temperature, since a complete exposition of all the data available would be too extensive for this presentation. Nevertheless, it is possible to make a reasonable approximation of the tensile properties in other conditions of cold-working and annealing by a correlation of the data previously presented on specific alloys and the data given here.

Jan 1, 1947

By E. Sengier

At the Director's dinner of the A.I.M.E. on. April 22, Mr. Sengier of the Union Minière du Haut Katanga was a guest. Though a member of the Institute for sev-eral years this was the first occasion on which he had had opportunity to meet with it, and in response to an invitation from President DeGolyer, after expressing his pleasure at being present, he told informally of the present development of the Congo with which he has been so closely related. From his remarks the follow-ing has been prepared.-EDITOR. AS you know, the Belgian Congo, a fairly large colony compared with the territory of Belgium, is in the center of Africa. Natural waterways, railroads now built and new railroads under construc-tion, give increasing means of transportation and are helping toward development. The mining industry is by far the most important part of our colonial activity. Considering that we are all engineers, I will confine my figures to mining enterprise. First I will show you the relative importance of the mining industry com-pared with the total exports of the Belgian Congo. During 1925 there was exported 100,000 tons of cop-per, valued at about $25,000,000; 900,000 carats of diamonds, 8000 lb. of gold, 1700 tons of cassiterite, 300 .tons of cobalt, and 20 grams of radium, of a total value of about $35,000,000. Other products to a value of about $12,000,000 and consisting mainly of palm nuts, palm oil, cotton, ivory, copal, rubber, were also exported. From this you will see that mineral products account for about 72 per cent of the total exported value. Copper alone amounts to 52 per cent of the total and 72 per cent of the mineral exports. All minerals, with the exception of gold, which is mined by the government, belong practically toy two mining companies in which American and British capi-tal is interested with Belgian. These two companies (one called Forminière, interested in the diamond busi-ness, and the other called the Union Minière, interested in copper, cobalt, tin and radium) were formed twenty-five years ago. They started producing in 1911, but the war prevented normal operations, and active de-velopment could only be carried on after the Armistice.

Jan 5, 1927

By Charles E. Wait

HAVING had some experience in the use of gasoline-gas in a laboratory, I have been induced by frequent inquiry to present a few hints concerning it, which I hope may be of some value to those who are out of the reach of coal-gas, and who contemplate using this gas. While I will not delay to describe the method by which this gas is made, it may not be out of place to note that, unless frequent charges are put into the carburetter, the gas is variable in richness. This may be partially avoided, it is said, by repeatedly pumping from one cell in the carburetter to another. If a machine is in constant use for many months without re charging, the gas becomes rather poor for illuminating purposes ; but in this condition it may be burned in a Bunsen burner with advan tage. Could the gas be used always in this condition, no difficulty would be experienced, and it would be quite satisfactory for general laboratory purposes. Considerable annoyance, however, is experi enced whenever the machine is filled with gasoline. The Bunsen and other burners then produce a flame too smoky to be used with com fort, and, in fact, with most of them, a full supply of air; turned on at the base of the burner, will not suffice to completely burn off all the carbon. Finding it necessary to adopt some method by which I could get a flame free from unconsumed carbon, I adopted a plan which has in every way proved satisfactory. In addition to the pipe conveying the gas to the table, and ar ranged with a stopcock, there is brought to the table, within a fern inches of the gas-pipe, another pipe, conveying air direct from the pump. This pipe is also arranged with a stop-cock. The air- and gas-pipes are now connected with one pipe by a T joint; and to this last pipe is attached, by rubber tubing, the Bunsen or other burner. I have successfully used this simple system in connection with both small and large Bunsen burners, a burner with three tubes, arid a Fletcher burner; and recently I have added a new still to our equipment, and have been tising with it a Fletcher special high power burner No. 6, to which this system has been applied. With

Jan 1, 1886

By George W. Sears

In preparing this symposium, our ambition was to elicit authoritative expression of opinion concerning important selected phases of the industry from men active in it. Responses to requests for contributions were gratifying, especially so in view of the short time available. The generous and cooperative spirit of the industry as a whole is amply evident. Responses were received from the following, who are therefore the true authors of the paper: W. G. Adamson, General Manager of the pershin; Quicksilver Co., Lovelock, Nev.; Dudley Baird, Vice President, Pacific Foundry Co., San Francisco; Walter W. Bradley, State Mineralogist of California; W. D. Burcham, General Manager of the Brewster Quicksilver Consolidated, Terlingua, Tex.; William Forstner, San Francisco; H. W. Gould, of H. W. Gould & Co., San Francisco; Marcus Hulings, General Manager of the Chisos Mining Co., Terlingua, Tex.; Frank J. Katz, Chief Engineer, Division Mineral Statistics, United States Bureau of Mines, Washington, D. C.; Lloyd J. Lathrap, Superintendent, Nevada Quicksilver Mines, Inc., Lovelock, Nev.; W. R. Moorehead, General Manager, New Idria Quicksilver Mings, Inc., Idria, Calif.; F. W. Oakes, Jr., Terlingua, Tex.; C. N. Schuette, San Francisco. Brief Economic History of Quicksilver in the United States Quicksilver ore was first discovered in the United States at what was later the New Almaden mine in California, in the year 1824. Production also began here, but not until 1850, when it was stimulated by the active demand caused by gold-mining operations. Prospecting for quicksilver was active, high-grade ores were found and ample production lowered the price from $100 per flask in 1850 to about half that figure for the greater part of the next 10 years. During the succeeding decade, many new quicksilver mines were found; production increased at a time when the local demand diminished, so that most of the product was exported. The third decade of quicksilver mining in the United States witnessed the development of the pan amalgamation process, particularly in Com-stock silver-mining operations. A suddenly increased demand sent prices soaring, the all-time peak of quicksilver production followed, and the highest price was soon replaced by the lowest one on record. Huge quantities of quicksilver were exported between 1870 and 1880 and exports continued in decreasing measure for three decades to 1910. In

Jan 1, 1930

By A. R. Jr. Amos

LOG washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate com-pletely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5° to 10° and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1936

By H. H. Otto

COMPARED with 1939, the year 1940 has seen no material change in the production of anthracite. Many factors seem to indicate a stabilized anthracite production of approximately 50 million tons per year. The present war has stimulated demand in the Cana¬dian and New England markets, which were formerly furnished with a portion of their needs from Great Britain and other European countries. Neither has there been any material change in the "bootleg coal" situation. This problem is more serious in the Southern anthracite field than in the Hazleton, Wilkes-Barre, and Scranton areas. One reason for this is the nearness of the Southern field to the large anthracite markets in Philadelphia, Washington, Baltimore, and Harrisburg. During the past year no new large

Jan 1, 1941

By AIME AIME

THE 1941 fall meeting of the Iron and Steel and the Institute- of Metal, Division held at the Ritz-Carlton Hotel, Philadelphia, during the first three days (Oct. 20-22) of the National Metal Congress was well attended as usual, and the seven technical sessions and the joint round table on order-disorder transformations were this year of considerably more than routine interest. Despite unseasonably warm weather, a scarcity of hotels (there were rumors, apparently well-founded, that , some of the metal man attending the Congress had to stay in tourist camp), and a multiplicity of technical and other ions of the co-operating societies that gave the Congress this year the general air of a three-ring circus the A.I.M.E. sessions attracted audiences that ragged from seventy or eighty up to 350

Jan 1, 1941

By J. F. K. Brown

ANTHRACITE?S satisfactory showing in 1942 was accomplished in the face of adverse conditions, such as the loss of man power to the active services and to other industries, and the difficulty and delay in obtaining the necessary materials and equipment required in mining operations. Although the in- creased output was stimulated by the war, and thus does not impress one as contributing to continuing improvement in the industry, nevertheless the year witnessed several efforts ant1 consideration of others that have the appearance of permanent progress.

Jan 1, 1943

By Robert :H. . Lesemann

I recently gave a talk at a seminar on mine development in the Eighties. I had to present CRU' s long-range market outlook for copper, lead, zinc, nickel, molybdenum and silver. In reviewing the recent history of each metal, and our projections, I tried to find some common pattern of behavior that could prove a guide in projecting future market behavior. When you sweep aside your input-output models and econometric equations, what you seem to be left with is this: "When a market goes through a prolonged period of price weakness, you can usually look forward to a period of considerable improvement. " "When a market goes through a prolonged period of price strength, you can always anticipate a prolonged period of price weakness." Stated another way, "The better things are, the worse they will get."

Jan 1, 1982

By John W. Cahn, John E. Hilliard

Single crystals of copper and silicon-iron were cold rolled in orientations chosen to produce individually the major components of the poly crystalline deformation texture. The orientation dependence of the recrystallization kinetics was studied relative to the primary recrystallization textures of these specimens. It is not possible to rationalize the poly crystalline re crystallized textures on this basis. The results suggest an important role of the interaction of adjacent crystals during the deformation of aggregates. BRICK and Williamson1 first noted evidence that the recrystallization temperature was different for straight-rolled and cross-rolled copper given comparable reductions. Michalak and Hibbard2 investigated quantitatively the effect of rolling procedure on the kinetics of recrystallization of cold-rolled copper and found that material cold-rolled the same amount by straight-pass, cross-pass, and compression-pass techniques developed different deformation and recrystallization textures, different 1-hr recrystallization temperatures, and different recrystallization kinetics. However, the temperature dependence of the rate of recrystallization was essentially the same for all techniques. Similar results were obtained on iron. Dunn and Koh3 in studying the recrystallization textures of cold-rolled silicon-iron single crystals reported large differences in the annealing temperatures and times required to recrystallize specimens of different orientations cold-rolled the same amount. Liu4 and Liu and Hibbard5 utilized the concept of different recrystallization temperatures for different orientations of cold-rolled crystals to rationalize the difference in recrystallization textures found in various face-centered-cubic metals. Their explanation predicted a significant difference in the recrystallization kinetics of deformed (110) [112] crystals as compared to (358) [352] crystals, and, in fact, Liu4 reported evidence that this difference existed at least qualitatively. Verbraak6 who rolled and recrystallized a series of copper single crystals found that the double (112) [111] rolled orientation is related to recrystallized cube texture formation. The effect of rolling intensity on the relative amount of cube component suggests an important role of recrystallization kinetics. Walter and Hibbard7 while trying to relate the behavior of rolled and recrystallized single crystals of silicon-iron to the behavior of polycrystal-line silicon-iron again noted that differences in recrystallization kinetics were necessary to rationalize their results. The purpose of the present investigation was to obtain quantitative kinetic data on the recrystallization of single crystals of both copper and silicon-iron rolled to initial isolated individual orientations corresponding to those found in the polycrystalline deformation textures. These data might indicate the importance of the deformation orientation, i.e. the range of available nuclei, the deformed matrix orientation into which these nuclei grow, and the orientation dependence of their growth rate during primary recrystallization on this texture. I. COPPER Experimental Procedure—A single crystal of 99.98 pet purity copper, grown by the Bridgman technique, was purchased in the form of a bar 1 1/2

Jan 1, 1962

By E. R. Kaiser

COAL research during 1942 was directed in an important degree toward the solution of problems of wartime importance. A wider selection of coals for carbonization to meet the increased demand for coke, and the improved utilization of lower-grade coals for boiler fuel were made possible by fundamental studies on cod and ash behavior that had been started several years ago. The coal industry's interest in the work of the various laboratories brightened significantly as results were demonstrated on smokeless combustion in stoves, on stokers without coke trees, and on pulverized firing of forge furnaces. Despite the limitations of priorities and scarcity of materials, the mineral industries building of the West Virginia University was completed and equipped with facilities for research on coal min

Jan 1, 1943

By George W. Riter

OUR mineral-land laws need revising so as to provide definite title at the outset to the mineral deposits within any definite piece of land. The laws as they now stand, especially those applicable to lodes, breed uncertainty as to rights of possession prior to patent; and to my mind this is the worst feature of all, worse even than the apex bugbear. It is now almost impossible for anybody to tell-with certainty what mineral rights exist within any area that is not covered by patent, or whether any valid rights exist at all. Our system is unique in permitting individuals to appropriate and exploit mineral lands of the public domain without notice of any kind to the Federal government, and to relinquish them without any ceremony at all. The result is a clouded record that cannot be cleared up until each claimant is put to some sort of final proof. In order to accomplish this, new Federal legislation will be required. The requirements for a mineral survey and the proceedings for patent have always been cumbersome and expensive; and perhaps out of regard for the poor claim owner, who can ill afford the outlay for that sort of thing, the law does not require him to go. through it unless he chooses to do so. Consequently, every active mining district has become encumbered with tangled groups of doubtful or conflicting locations, whose rights and boundaries, when any valuable ore is found, must usually be determined by lawsuits that are as expensive and as distressing as the stakes are high. So deeply has litigation entered into our mining system that a claim whose rights have never been disputed would probably be set down offhand, by $miner of the old school, as of no value. Think of the litigation over rights of possession on the Com-stock lode—12 leading companies involved 'in an aggregate of 245 suits within a period of less than eight years! Ambiguous local records; the chance of erroneously placed or obliterated monuments; doubt as to the sufficient performance of the statutory annual labor; uncertainty as to prior conflicting or overlapping locations; anxiety as to the changing attitude of the Department of the Interior and the Forest Service—such considerations as these make an unpatented mining claim an unclean thing in the eyes of possible investors. Is it any wonder that they keep themselvesand their money at a safe distance,

Jan 1, 1915

By Robert F. Brindisi

There are approximately thirty to forty operating mills in the United States which are currently producing uranium yellow cake. This figure includes a significant number of in situ and by-product operations however the conventional acid leach flowsheet depicted in Figure 1 is the most common process used by domes- tic yellow cake producers. Ground ore is leached with sulphuric acid and the solids are separated from the pregnant liquor and washed in a series of counter- current decantation thickeners. After clarification of the pregnant liquor, uranium is recovered from the solvent extraction/stripping circuit by the addition of ammonia with precipitation of ammonium diuranate, or simply yellow cake. The yellow cake precipitate is then thickened in a conventional thickener before re- porting to the dewatering/washing unit operation. De- watered solids subsequently report to thermal drying, and clarified liquor from the dewatering/washing step is recycled to the yellow cake thickener. The yellow cake dewatering/washing unit operation is generally accomplished using either a solid bowl centrifuge or a rotary vacuum drum filter. In most cases the underflow from the yellow cake thickener is pumped to the dewatering/washing unit operation at approximately fifteen to twenty percent solids. For the purpose of this discussion ammonium diuranate, the product of ammonia precipitation from a conventional acid-leach uranium mill flow sheet, as discussed earlier, will be considered. With only slight adjustment this discussion will be equally applicable to sodium diuranate or uranium perioxide precipitates and to either in situ or by-product operations where such precipitates are generated. Some of the domestic uranium mills which have selected solid bowl centrifuges instead of vacuum drum filters for the dewatering/washing unit operations are listed in Figure 2. Why have these uranium mills, as well as others not listed, chosen to use the solid bowl centrifuge for this particular application? It is simply a matter of performance, reliability and economics. In the remainder of this paper the performance, initial cost, installation cost, maintenance and power consumption of both the solid bowl centrifuge and the rotary vacuum drum filter will be com- pared. In order to provide a consistent basis for comparison the appropriate sized (centrifuge or filter) unit for the dewatering/washing of 400 to 500 pounds per hour of yellow cake solids will be considered. Such a flow will usually be generated by a typical 3,000 ton per day (acid-leach) uranium mill.

Jan 1, 1980

By Robert Linton

SPECIFICATIONS for clays serving raw materials in the ceramic industry usually contain the following items: (1) Chemical analysis, sometimes with mineralogical structure determined by microscopic investigation. (2) Maturing temperature and firing range, usually expressed in terms of pyrometric cone equivalent. (3) Shrinkage (drying and firing shrinkage separately). (4) Degree of plasticity. (5) Color after firing. Clays may be classified, according to the purpose of the classification, in several different ways, based on (1) Geological occurrence-transported, altered An place, indurated (shales). (2) Physical properties-plastic (bonding clays, ball clays) and nonplastic (flint clays, kaolins or china clays, bone clays). (3) Color. (4) Use. A common classification of clays for commercial designation, and one fol-

Jan 1, 1936