Search Documents

By E. T. Dumble

In the Bosquejo Geoldgico de Mexico, published in 1897 by the Secretaria de Fomento as Nos. 4, 5 and 6 of the Boletin del Institute Geologico de Mexico, the Director, Jose C. Aguilera, after a detailed account of the geological observations made by himself and his assistants on their several trips through the various districts of the Republic, gives in Part 2 a synopsis of the geology of Mexico, describing . al1 the formations recognized, the rocks comprised in them, their geographical distribution, disturbances, principal eruptions and economic features, as explanatory of the Geological Map of Mexico. In Part 3 Prof. Ordonez describes many of the interesting eruptive rocks of Mexico." This work brings together in a very satisfactory way about all of the published results of geological investigations in Mexico; and although the determinations of the authors with reference to some of the sedimentary deposits are very different from those of other writers, they seem to be based upon good paleontological grounds in each instance. From the map and the text of this paper it appears that the condition of knowledge in regard to the geology of the State of Sonora, at the time of its publication, was about as follows: The western portion of the State, lying between the coast line of the Gulf of California and the foot-hills of the Sierra Madre mountains, is largely Quaternary, interrupted by areas of Azoic rocks and of later eruptives, with two or three limited exposures of limestones of the Cretaceous; while the eastern or

Jan 1, 1900

By Chikaosa Tanimoto

INTRODUCTION The committee on Rock Mechanics, Japanese Society for Civil Engineers, has been discussing 'soft rock engineering in Japan' and presented several papers concerning dam, tunnel, bridge and slope constructions to International Symposium on Weak Rock, Tokyo 1981. This is the summarized paper based on References of Okamoto et a1 (1981), Iida et a1 (1981), Working Group on Tunneling-JSCE (1981), Working Group on Bridge Foundations-JSCE (1951) and Kikuchi et a1 (1981), which can convey general view on engineering experiences with weak rocks in Japan. From the point of view to the origin and/or distinctive physical properties, weak rocks in Japan may be classified into (1) sedimentary, (2) weathered, (3) low welded-pyroclastic and (4) fractured ones. Their typical characteristics are summarized in the following section. Concerning dam foundations on soft rock, several hundreds have already been constructed and, at present, nearly one hundred are under construction or at planning stage. These dams, almost without exception, have some problems such as site selection, material selection for fill-type and concrete dams, design of dam and its foundation, and construction procedures, requiring special ingeneous and cautious measures to cope with the local geotechnical difficult situations. In tunneling, for the decade of 1970s, the number of tunnels in soft rock either completed or under construction was at least 160, including Seikan Tunnel of 53.9 km long, Nakayama Tunnel of 14.8 km long and so on. Most of these tunnels are distributed in the northern half of Mainland, consisting of a basement of Paleozoic strata and Plutonic rocks, overlayed by Neogene Tertiary formations which include large

Jan 1, 1982

By Carl Henrich

Aspen, the flourishing mountain- and mining-town of Pitkin county, Colorado, is located in the valley of the Roaring Fork, 11 miles above Glenwood springs, where that stream empties its waters into Grand river, a tributary of the Colorado. The Roaring Fork heads on the western slope of the Sawatch range near Grizzly peak, and runs in a general northwesterly direction to its junction with the Grand river. Of its numerous tributaries, Castle creek joins it just below the town of Aspen, the town being built on an extensive flat hounded on the northeast by the Roaring Fork and on the west by Castle creek. The latter heads at the junction of the Sawatch and the Elk mountains and flows northward between the two chains, until it empties into Roaring Fork. Opposite the town of Aspen, Hunter creek, coming westward from the western slope of Mount Massive, joins the Roaring Fork. About a mile north of Aspen, the bed of Hunter creek is at least 300 feet higher than that of the Roaring Fork at Aspen. Hunter creek forms thus, at its mouth, one of the best water-powers in Colorado. A portion of it is now utilized for electric lighting in Aspen, while in the near future, the whole of this magnificent natural power will be applied, through electric transmission, for hoisting, pumping and ventilating at different mines of the district. The mountain opposite the town of Aspen, on the east side of Hunter creek (which near its mouth flows southerly), is called Smuggler mountain, from the famous mine at the foot of it. On the other, or western, side of Hunter's creek (see map, Fig. I), a higher mountain rises, on the slope of which the regular dip of the Triassie or Upper Carboniferous red sandstone strata, alternating with white layers of the same rock, can be clearly seen from town. This mountain is called Red mountain, from the prevailing color of its rocky

Jan 1, 1889

By John F. Elliott, John R. Rawling

The rate of reduction of silica to silicon by carbon at 1550° to 1700°C in iron blast-furnace type slag-metal systems has been investigated. In the tower portion of the temperature range oxygen transport in the metal boundary layer at the slag-tal interface is probably rate limiting. A second step, which apparently involves a chemical process in the slag at the slag-metal interface, appears to be rate limiting when the oxygen-transport limitation is avoided. Above 1650°C rate control of the reduction by carbon probably is mixed between the two steps. INVESTIGATIONS1.2 into the equilibrium distribution of silicon between graphite-saturated slags and metals typical of iron blast-furnace practice show that, under the experimental conditions specified, the reduction of silica to silicon is relatively slow compared with the rates of other slag-metal reactions under similar conditions. For this reason, the reduction of silica in blast-furnace slag-metal systems was considered to be an interesting subject for further study. Investigations of the kinetics of the reaction3-5 suggest that several possible steps may be rate controlling, and that the rate-controlling step depends not only on the physical state of the systems but also on the configuration of the apparatus. The main objects of the investigation reported here were to sug- gest plausible reaction paths for the reduction of silica under the experimental conditions chosen and to determine the step or steps which control the rate of reduction of silica. EXPERIMENTAL Two types of experiments involving the reduction of silica from the slag were carried out. In the first, the only reducing agent present was carbon (graphite), for which the over-all reaction is (SiO2) +2C(gr) —Si + 2Co(g) [l] The second type was a graphite-saturated ferro-silicon-iron concentration cell. In it silica in the slag could be reduced either by carbon according to Eq. [I], or by a reaction of electrochemical nature in which silicon was oxidized at the ferrosilicon-slag interface and silica was reduced at the slag-iron interface without the formation of CO. The two types of experiment are described below. Reduction of Silica with Carbon as the Only Available Reducing Agent. The reduction of silica was accomplished by allowing a liquid lime-alumina-silica slag and graphite-saturated iron to react in an induction-heated graphite crucible. The crucible was 2.25 in. diameter and 5 in. deep; it was fitted with a graphite stirrer which penetrated through the slag and into the metal, Fig. 1. The slag and metal charges weighed 350 g each. Pure carbon monoxide at a pressure of 1 atm was maintained above the melt by passing the purified gas through the crucible at a rate of 0.5 liter per min. The gas did not stir either the slag or metal. Temperature measurements were made by sighting an optical pyrometer down the hollow stirrer rod into a 1/4-in. hole drilled in the stirrer blade. The crucible temperature was maintained within *15"C of the required value by manual control of the power supply to the

Jan 1, 1965

By E. T. Turkdogan, L. S. Darken

Using the quadratic formalism, thermodynamic equations are derived for the composition dependence of the heat and entropy of mixing. The applicability of these equations is confirmed by available experimental data on the activities and heats of mixing for binary metallic systems of Group ZZB elements. In a recent paper arkeen' introduced a quadratic formalism describing the composition dependence of the activity coefficient in the terminal regions of binary metallic solutions. That is, in the terminal region, which may extend to as much as 60 at. pct, the logarithm of the activity coefficient, log y,, of component 2 is a linear function of (1 - N,)' where N2 is the atom fraction of component 2. Similarly, for the other component, log yl is a linear function of (1 - N,)'. A number of iron-base binary liquid alloys were shown to obey this quadratic formalism. arkeen' extended this formalism also to any corner of a ternary system and showed that the activity coefficients of the components 1, 2 and 3 (1 is taken as the solvent) can be represented by quadratic terms involving five parameters, four of the binaries and one for the ternary system. Numerous examples given by arkeen' demonstrated the general applicability of the quadratic formalism to iron-base systems over a wide composition range. In this paper further examples are given of binary liquid systems (Group IIB elements, Zn, Cd, and Hg) and of several solid solutions, again demonstrating the appropriateness of this concept. A further purpose of this paper is to extend the quadratic formalism to the enthalpy and excess entropy of binary metallic solutions and to test the equations so found using available experimental data. QUADRATIC FORMALISM FOR HEATS AND ENTROPIES OF MIXING OF BINARY METALLIC SOLUTIONS The following equations, reproduced from Darken's paper, are for the two terminal regions of binary systems. at infinite dilution and a's are temperature dependent parameters to be determined from the experimental data. Although the quadratic formalism is an assumed representation of the data, Eqs. [I] to [4] are thermo-dynamically consistent with the Gibbs-Duhem relation and satisfy Raoult's and Henry's laws as limiting cases. As pointed out previously,' the following form of the Gibbs-Duhem equation facilitates the integration in general but particularly in regions I and 11, where each of the derivatives is constant. The partial molar enthalpy of solution i, (and i; the value of i, at infinite dilution) are related to the activity coefficients y, and y," by the thermodynamic relation Differentiating Eq. [l ] with respect to 1/T and substituting the above thermodynamic relation gives for region (I) It is reasonable to assume that over a temperature range of experimental interest, the enthalpy of mixing is essentially independent of temperature, implying from Eq. [7] that the derivative da,,/d(l/) is also independent of temperature. On the basis of this argument, the temperature dependence of a has the form where £ and S have the units of enthalpy and entropy respectively; they are characteristic parameters for a terminal region of a binary system, e.g. for region (I), C12, S12 and for region (II), d:,,, S2,. Using this equation gives for dff ,/ d(l/), From Eqs. [7] and [9] an expre_ssion is obtained for the composition dependence of L,. Similar calculations are made for El and the results are summarized below for the two terminal regions. For region (I), The corresponding expressions for the molar heat of solution, AHM, are readily obtained from the above equations for the two terminal regions: For region (I),

Jan 1, 1969

By Alexander L. Field

This paper contains an account of experimental results obtained in an extensive investigation of steels containing zirconium. There recently appeared' an announcement by F. M. Becket, at whose suggestion and under whose general direction this investigation was made, a statement of the outstanding features of the work and a brief explanation of the factors that led to its inception. It is not possible, in a paper of this character, to record all of the operating and test data collected, which includes the production of more than 350 heats of steel. The difficulty of a complete presentation is increased by the fact that several lines of experimentation are too incomplete to warrant publication of the results at the present time. In addition to the methods of manufacture and test employed in the work, there is described experimental evidence on which are based certain definite conclusions regarding the remarkable effects brought about by the presence in steel of relatively small percentages of zirconium. When added to a molten steel bath, zirconium combines chemically with dissolved oxygen, nitrogen, and sulfur, in the order named, and is capable of neutralizing the embrittling effect of phosphorus in whole or in part; although in the case of phosphorus there is no evidence so far of actual chemical combination. These effects arc not in the nature of suppositions supported by theory, nor is their existence deduced merely on the basis of analytical evidence. In each phase of its relation to or reaction with the four impurities mentioned, zirconium affects beneficiauy the mechanical properties of the steel to which it is added, in a manner which it is one of the purposes of this paper to explain in terms of a tentative working theory.

Jan 1, 1923

By P. N. Nikiforuk, M. C. Zoerb

An analog computer model has been developed of a large, walking dragline. This model permits changes in the configuration of the dragline, or changes in its digging cycle, to be readily investigated on a computer. As a result, it is possible to determine ways of improving the dragline performance without having to carry out many expensive experiments on the actual machine. This model can also be used as a simulator for dragline operator training. INTRODUCTION The movement of large volumes of material is always a costly operation and the increasing trend towards the use of large capacity equipment does not necessarily produce the economy desired. This problem is of particular concern to the mining industry in its open-pit operations where large draglines are used to remove the overburden. Since this operation often forms a very large part of the total cost of open-pit mining it is particularly important that it be kept as economical as possible. This requires that the dragline be operated at its maximum possible productivity. In order to optimize the operation of a dragline it is desirable that a suitable model of the dragline be available for study. Once such a model is available the effects of changes in the configuration of the dragline, or changes in its digging cycle, could be readily investigated on a computer and methods of improving its performance could be determined without having to carry out expensive experiments on the actual machine. Such models would be of use not only to dragline users, but also to the manufacturers of draglines for design purposes. Presumably studies of this type could eventually lead to computer-con trolled stripping operations. As far as can be determined very little work1'2 has been done on the derivation of dragline models. Such models must be derived before work of the nature indicated in the previous paragraph can be carried out. As a small contribution to this field this paper describes work that has been carried out by the senior author during the past few years on the derivation of one such model. This model describes the drag, hoist and swing operations of a 35 cu yd, commercially available, walking dragline. This model was derived for use with an analog computer and can be used either for optimization studies, or for the training of dragline operators. DESCRIPTION OF DRAGLINE General: The particular dragline for which an analog computer model was developed is owned by the Great West Coal Company of Estevan, Saskatchewan. It is a walking dragline and its function is to remove 40

Jan 1, 1967

By Kenneth P. Katen

INTRODUCTION Though the use of continuous mining machines consolidated the operations of cutting, drilling, blasting, and loading in one machine that would theoretically provide uninterrupted production, it was soon realized that the face haulage and roof support operations remained as major impediments to continuous production. The ability to provide not only continuous cutting and loading, but also continuous haulage and roof support (see Fig. I), was the basis for the introduction of mechanized longwall systems in this country from Europe in 1951. The early systems employed friction props for roof support, but were to become obsolete shortly after introduction of the first hydraulically powered, self-advancing supports in 1960. Since then, use of the longwall technique has grown to the point where it is currently providing more than 5% of the annual output of underground coal mines in the United States. The shortwall system had its origin in Australia, but was first introduced into this country in 1962 following the development of powered roof supports. It, too, provides for continuous cutting, loading, and roof support (see Fig. 2), but has not experienced the widespread popularity of longwall due to its inherent inability to easily provide for continuous haulage. While there are in the neighborhood of 100 longwall systems currently in operation in this country, there are only a handful of short- wall operations providing production of slightly more than 907 184.7 t/a (1,000,000 stpy) Both of these systems provide uninterrupted roof support for face operations by means of hydraulically powered steel roof supports. In each case, the coal removal consists of open-end cuts made from the narrow end of a large rectangular pillar (panel) which has been blocked out by continuous miners developing entries around its perimeter. However, this is the extent of the similarities between the two systems. It is hoped

Jan 1, 1981

By R. C. Hassinger, D. V. von Rosenberg

Transverse dispersion has received considerably less treatment in the literature than has longitudinal dispersion. Different methods for determining transverse dispersion coefficients have been used in different investigations, and the results obtained have not been consistent enough to permit accurate generalizations as to the effect of various physical parameters on the magnitude of these coefficients. A numerical solution to the differential equation describing transverse dispersion in the absence of longitudinal dispersion was obtained to enable one to calculate the dispersion coefficient from experimental results. The more general dispersion equation including longitudinal dispersion also was solved numerically to give quantitative limits of a dimensionless group within which the assumption of negligible longitudinal dispersion is justified. Possible experimental procedures were examined, and one utilizing a cylindrical packed column was chosen for the determination of transverse dispersion coefficients. Values of these coefficients were determined for a system of two miscible organic fluids of equal density and viscosity, for two sizes of packing material over a wide range of flow rates in the laminar regime. The dispersion coefficient was found to decrease, for a constant value of the product of packing size and interstitial velocity, as the size of the packing material particles increased. INTRODUCTION Longitudinal dispersion has received extensive treatment in the literature, and consequently is better understood than its orthogonal counterpart, transverse dispersion. Many mathematical models of dispersion processes assume that transverse dispersion is rapid enough to damp out any radial** concentration gradients and therefore may be neglected. Laboratory and production results, however, indicate that this is a poor assumption.l,2 Various experimental procedures for determining transverse dispersion coefficients have been used in previous investigations, but the results have generally been expressed by similar correlations. The transverse dispersion coefficients obtained, however, have often varied considerably for given values of the correlation parameters. We feel that further experimental determinations of transverse dispersion coefficients will help alleviate some of the inconsistencies in these empirical correlations. One assumption implicit in all previous investigations is that of negligible longitudinal dispersion in the experimental system. An attempt to justify this assumption often is made using intuitive reasoning, but it is apparent that this reasoning must break down as the condition of zero flow rate is approached. A mathematical examination of the equations describing the system yields physical limits outside of which the assumption of negligible longitudinal dispersion is invalid. BACKGROUND In a porous medium, the "effective molecular diffusivity" De is less than the molecular diffusivity D measured in the absence of a porous medium, due to the tortuous path which a diffusing molecule must travel. Various authors3-5 have reported values of the ratio De/D in the range of 0.6 to 0.7. When there is fluid flow within the porous medium, mass transfer occurs by convective dispersion as well as by molecular diffusion. These are separate phenomena and can be treated as such on a microscopic scale. However, the mathematical complexity is such that only extremely simple geometries could be considered, and the results hardly would be applicable to the complex geometries existent in actual porous media. A more

Jan 1, 1969

By T. D. Yensen

I. INTRODUCTION IT is safe to say that of all the different materials that go to make up electrical machinery, iron is the most important. Upon its -magnetic and electrical quality depends not only the efficiency of the machine but, to a very large extent, the cost. Aside from the mechanical strength, there are three characteristics of iron that are of importance in this connection, viz., magnetic hysteresis, electrical resistance, and magnetic permeability. In the homopolar machine, where the magnetic flux is unidirectional, permeability is the only important factor, but in all other machines the flux is reversed in one or more parts and causes losses due to hysteresis and eddy currents. The eddy-current loss depends largely upon the electrical resistance of the iron; the higher the resistance the lower the loss, under otherwise identical conditions. These hysteresis and eddy-current losses cause heating of the machine, and as they depend upon the magnetic density in the iron, this density must be regulated so that the heating shall not be excessive. If the hysteresis and eddy-current Josses and the permeability of the magnetic circuit will permit an increase in the magnetic density, or, in other words, a decrease in the amount of iron, this in turn will mean a decrease in the amount of copper needed, with a consequent decrease in the copper loss. It is thus seen that; indirectly as well as directly, the above characteristics have an important bearing on both the efficiency and the cost of electrical machinery. In general, it may be said that iron for electrical machinery should have the following characteristics: (1) low hysteresis loss, (2) high electrical resistance, and (3) high permeability. These are the characteristics that investigators have been striving to attain since electrical machinery first came into use.

Jan 2, 1916

By Alexander L. Field

This paper contains an account of experimental results obtained in an extensive investigation of steels containing zirconium. There recently appeared' an announcement by F. M. Becket, at whose suggestion and under whose general direction this investigation was made, a statement of the outstanding features of the work and a brief explanation of the factors that led to its inception. It is not possible, in a paper of this character, to record all of the operating and test data collected, which includes the production of more than 350 heats of steel. The difficulty of a complete presentation is increased by the fact that several lines of experimentation are too incomplete to warrant publication of the results at the present time. In addition to the methods of manufacture and test employed in the work, there is described experimental evidence on which are based certain definite conclusions regarding the remarkable effects brought about by the presence in steel of relatively small percentages of zirconium. When added to a molten steel bath, zirconium combines chemically with dissolved oxygen, nitrogen, and sulfur, in the order named, and is capable of neutralizing the embrittling effect of phosphorus in whole or in part; although in the case of phosphorus there is no evidence so far of actual chemical combination. These effects arc not in the nature of suppositions supported by theory, nor is their existence deduced merely on the basis of analytical evidence. In each phase of its relation to or reaction with the four impurities mentioned, zirconium affects beneficiauy the mechanical properties of the steel to which it is added, in a manner which it is one of the purposes of this paper to explain in terms of a tentative working theory.

Jan 1, 1923

By Frank N. Speller

Jan 1, 1934

By R. E. Somers

1. INTRODUCTION 1. Location, Topography, and Climate The Burro Mountains are located in the southwestern part of New Mexico, in Grant County. The group is made up of two distinct moun-tain masses, known as the Little Burros and the Big Burros, the former lying about 6 miles southwest of Silver City-, and the latter about 9 miles farther in the same direction. They are separated by the valley of the Mangas River, a tributary of the Gila, and a stream only in name, except after a heavy down-pour of rain. . The Little Burros attain an elevation of 6,625 ft. above sea level, and the Big Burros 8,054 ft., with the surrounding country averaging about 6,000 ft. To the south of these mountains stretches the desert plain, while to the north are the more frequent elevations of the mountainous country.

Jan 5, 1915

By Lawrence B. Wright, Lester G. Morrell

On the steep slopes of the Kootenays, 15 to 20 miles south of Nelson, B. C., are a number of ore occurrences (Fig. 1). One that has many features of mining and geological interest is the Ymir Yankee Girl Gold Mines Limited. Discovery of this property was made in 1899 at an outcrop on the hillside, some 2500 ft. above the village of Ymir. This proved to be a branch vein 20 ft. long leading to two main veins, the Yankee Girl and the Spur (Fig. 5). The ore pattern as now delimited shows a remarkable increase in ore area with depth below the outcrop. This recent development is of interest particularly in view of the fact that the property was nearly condemned, professionally. Another interesting feature, which has a bearing upon its history, is the persistent excess of tonnage produced from period to period over visible reserves. This is not ascribed to lagging mine development, but to detailed vein characteristics, which we will endeavor to make clear by giving a description of the veins and their surroundings. HISTORY AND PRODUCTION Little interest_was_evidenced-in this-distriet until the building of the railway in 1893 provided easy access and the discovery of the Ymir mine in 1896 attracted attention. As a result, the Ymir Yankee Girl group of claims was staked in October 1899. In 1907, an American syndicate took over the property and subsequently extended the 50-ft. drift and opened the present 400 and 540-ft. levels. In 1908, the Syndicate, without recording any shipments in the meantime, dropped its lease, which was taken up by H. L. Rogers, who bonded the Yankee Girl group. Rogers shipped 2622 tons of ore, mainly from the uppermost stope in the mine, which is reported to have yielded

Jan 1, 1940

Safety Factor Characteristic Curves. Their Application to Mine Hoisting Ropes. (Paper by W. A. Boyer, Transactions AIME, 199, 989; Mining Engineering, October 1954. Discussion by B. E. Grant.) ............................................................................................................................. 1101 The Use of Wooden Rock Bolts in the Day Mines. (Paper by Rollin Farmin and Carville E. Sparks, Transactions AIME, 196, 922; Mining Engineering, September 1953. Discussion by Edward Thomas.) ................................................................................................................................. 1101 An Analysis of Mine Opening Failure by Means of Models. (Paper by Bernard York and John J. Reed, Transactions AIME, 196, 705; Mining Engineering, July 1953. Discussion by J. P. Zannaras.) ... 1102 B — Minerals Beneficiation Flotation and the Gibbs Adsorption Equation. (Paper by P. L. de Bruyn, J. Th. Overbeek, and R. Schuhmann, Jr., Transactions AIME, 199, 519; Mining Engineering, May 1954. Discussions by W. E. Ewers and Masayoshi Wada.)........................................................................................... 1103 Manganese Upgrading at Three Kids Mine, Nevada. (Paper by S. J. McCarroll, Transactions AIME, 199, 289; Mining Engineering, March 1954. Discussion by J. Bruce Clemmer, J. B. Rosenbaum, and C. H. Schack.)............................................................................................................. 1105 A Physical Explanation of the Empirical Laws of Comminution. (Paper by D. R. Walker and M. C. Shaw, Transactions AIME, 199, 313; Mining Engineering, March 1954. Discussions by Dimitri Kececioglu, George B. Clark, and Fred C. Bond.) ......................................................... 1106 F — Coal Underground Electrocarbonization of Coal and Related Hydrocarbons. (Paper by T. C. Cheasley, J. D. Forrester, and Erich Sarapuu, Transactions AIME, 199, 908; Mining Engineering, September 1954. Discussions by John G. Tripp and James L. Elder.)....................................................... 1108 Longwall Mining and Mechanization, with Special Reference to Nova Scotia. (Paper by Frank Doxey, Transactions AIME, 199, 701; Mining Engineering, July 1954. Discussion by Louis A. Turnbull.) ........................................................................................................................................ 1109 Cleaning Various Coals in a Drum-Type Dense-Medium Pilot Plant. (Paper by M. R. Geer, W. A. Olds, and H. F. Yancey, Transactions AIME, 196, 696; Mining Engineering, July 1953. Discussion by John Griff en.)................................................................................................................................. 1110 Frontiers in Heat Extraction from the Combustion Gases of Coal. (Paper by Elmer R. Kaiser, Transactions AIME, 199, 304; Mining Engineering, March 1954. Discussion by G. A. Vissac.) ............ 1112 Exploration of the Oaxaca Coal Fields in Southern Mexico. (Paper by Luis Toron and Salvador Cortes-Obregon, Transactions AIME, 199, 505; Mining Engineering, May 1954. Discussion by John D. Price.).................................................................................................................. 1113 H — Industrial Minerals Alkali Reactivity of Natural Aggregates in Western United States. (Paper by William Y. Holland and Roger H. Cook, Transactions AIME, 196, 991; Mining Engineering, October 1953. Discussions by Dexter H. Reynolds and W. L. Merritt.) ......................................................... 1114 Characteristics of Titaniferous Concentrates. (Paper by L. E. Lynd, H. Sigurdson, C. H. North, and W. W. Anderson, Transactions AIME, 199, 818; Mining Engineering, August 1954. Discussion by D. R. Grantham.)........................................................................................................................ 1116

Jan 1, 1955

By T. C. Wilson, Gerald Edmunds, W. M. Peirce, E. A. Anderson

Thirty-six elements have been alloyed singly with cartridge brass. Ammonia and mercury stress-cracking tests have been conducted on the as-rolled and recrystallized strip. Ultra high purity cartridge brass has also been tested. Silicon improves stress- cracking behavior. High silicon (I per cent) cartridge brass quenched from high temperature (for example, 800 C.) annealing is exceptionally resistant to ammonia stress cracking. This improvement is not lost by subsequent cold working, but is greatly reduced by subsequent low temperature annealing. Phosphorus, arsenic, barium, cerium, magnesium, tellurium, tin, beryllium, and manganese benefit stress-corrosion resistance under some circumstances, but not others. The other alloying additions tried had no large effect on stress-cracking resistance. None of the elements added accelerated stress cracking. The impurities in commercial brass are not responsible for season cracking.

Jan 1, 1945

By J. L. Gillson

In a brief summary of the many occurrences of fluorspar in our western states, it is not possible to go into detail in regard to the geology, mining and milling methods, and reserves about individual deposits. Rather a broad review is made of the occurrences and an analysis of how the western deposits may fit into our future domestic economy is presented. General Statement on Fluorspar Situation Fluorspar has been used for years as a flux in the manufacture of basic open-hearth steel, in foundry cupolas for melting pig iron, in the manufacture of opalescent glass and in the preparation of hydrofluoric acid. In 1880 the annual production of fluorspar in the United States was around 4000 tons per year. By 1900 it was up to 21,656 tons and between 1902 and 1908 it averaged about 40,000 tons annually. Prices were then so low, by present standards, that it seems impossible to believe now that mining could have been performed profitably at the price levels then prevailing. In 1890 fluorspar sold at the mines for $6.70 per ton, in 1901 for $5.81, in 1916 for 85.92. When the United States entered World War I, flyorspar production and price skyrocketed; the production reached 263,817 tons in 1918, with prices above $20.00 per ton, and prices were even higher in 1919 and 1920. After 1920, the domestic production fell from the 1918 level to about 125,000 tons annually and the average price dropped back to about $18.00 per ton. By 1935 the average price had fallen to $15.00, but in 1940 with a rising demand the average price of all grades had gone back up to $20.31. Today it is 75 per cent higher than in 1940 and presumably the price of acid grade at .least would be even higher if it were not for price ceilings. The first subsequent year that the domestic production exceeded that of 1918 was 1941, and the 1944 production is expected to exceed 400,000 tons, or over one and a half times that of 1918. In five-year periods, average production and imports were as are shown in Table I. Many people concerned with the consumption of fluorspar believe that the postwar period ahead will show a repetition of price trends of the last such period. They believe that imports will be again an important factor in the available supply and the price will fall back gradually toward the prewar level. The following basic factors are pertinent in analyzing this conclusion:

Jan 1, 1948

By J. L. Gillson

In a brief summary of the many occurrences of fluorspar in our western states, it is not possible to go into detail in regard to the geology, mining and milling methods, and reserves about individual deposits. Rather a broad review is made of the occurrences and an analysis of how the western deposits may fit into our future domestic economy is presented. General Statement on Fluorspar Situation Fluorspar has been used for years as a flux in the manufacture of basic open-hearth steel, in foundry cupolas for melting pig iron, in the manufacture of opalescent glass and in the preparation of hydrofluoric acid. In 1880 the annual production of fluorspar in the United States was around 4000 tons per year. By 1900 it was up to 21,656 tons and between 1902 and 1908 it averaged about 40,000 tons annually. Prices were then so low, by present standards, that it seems impossible to believe now that mining could have been performed profitably at the price levels then prevailing. In 1890 fluorspar sold at the mines for $6.70 per ton, in 1901 for $5.81, in 1916 for 85.92. When the United States entered World War I, flyorspar production and price skyrocketed; the production reached 263,817 tons in 1918, with prices above $20.00 per ton, and prices were even higher in 1919 and 1920. After 1920, the domestic production fell from the 1918 level to about 125,000 tons annually and the average price dropped back to about $18.00 per ton. By 1935 the average price had fallen to $15.00, but in 1940 with a rising demand the average price of all grades had gone back up to $20.31. Today it is 75 per cent higher than in 1940 and presumably the price of acid grade at .least would be even higher if it were not for price ceilings. The first subsequent year that the domestic production exceeded that of 1918 was 1941, and the 1944 production is expected to exceed 400,000 tons, or over one and a half times that of 1918. In five-year periods, average production and imports were as are shown in Table I. Many people concerned with the consumption of fluorspar believe that the postwar period ahead will show a repetition of price trends of the last such period. They believe that imports will be again an important factor in the available supply and the price will fall back gradually toward the prewar level. The following basic factors are pertinent in analyzing this conclusion:

Jan 1, 1948

By Lawrence B. Wright, Lester G. Morrell

On the steep slopes of the Kootenays, 15 to 20 miles south of Nelson, B. C., are a number of ore occurrences (Fig. 1). One that has many features of mining and geological interest is the Ymir Yankee Girl Gold Mines Limited. Discovery of this property was made in 1899 at an outcrop on the hillside, some 2500 ft. above the village of Ymir. This proved to be a branch vein 20 ft. long leading to two main veins, the Yankee Girl and the Spur (Fig. 5). The ore pattern as now delimited shows a remarkable increase in ore area with depth below the outcrop. This recent development is of interest particularly in view of the fact that the property was nearly condemned, professionally. Another interesting feature, which has a bearing upon its history, is the persistent excess of tonnage produced from period to period over visible reserves. This is not ascribed to lagging mine development, but to detailed vein characteristics, which we will endeavor to make clear by giving a description of the veins and their surroundings. HISTORY AND PRODUCTION Little interest_was_evidenced-in this-distriet until the building of the railway in 1893 provided easy access and the discovery of the Ymir mine in 1896 attracted attention. As a result, the Ymir Yankee Girl group of claims was staked in October 1899. In 1907, an American syndicate took over the property and subsequently extended the 50-ft. drift and opened the present 400 and 540-ft. levels. In 1908, the Syndicate, without recording any shipments in the meantime, dropped its lease, which was taken up by H. L. Rogers, who bonded the Yankee Girl group. Rogers shipped 2622 tons of ore, mainly from the uppermost stope in the mine, which is reported to have yielded

Jan 1, 1940

By N. F. Foster

The use of piezoelectric semiconducting materials for the fahrication of ultrasonic transducers has raised the upper fundamental frequency limit for transducers from about 200 mc to above 10 kmc, Several types of semiconductor transducer configurations have been proposed and examined experimentally. Depletion-layer transducers have been made and operated at frequencies below 1 kmc hut they appear to he better suited for operation at considerably higher frequencies around 10 knzc. Diffusion-layer transducers have been made and operated in the range 50 to 1000 mc and have exhihited considerably improved conversion losses and bandwidths compared with other transducers available in the frequency range. A variety of novel structures are possible using these new types of transducers, some of which could lead to substantial advances both in research and in the fabrication of ultrasonic delay lines and memory elements. THE field of ultrasonics today spans some five decades of the frequency spectrum from the audible to the kmc range and finds applications ranging from fundamental research into the atomic structure of matter to the degreasing of machine parts. To cover this wide range it has been necessary to develop a great many types of ultrasonic trandsucers utilizing a variety of materials and physical phenomena. The first ultrasonic transducers were made during World War I for a submarine-detection system. They consisted of plates of single-crystal quartz bonded between metal plates and were one of the first applications of the phenomenon of piezoelectricity discovered nearly 30 years previously. Despite the many advances which have been made in transducer technology, piezoelectric transducers using single-crystal quartz are still used almost exclusively for application above about 30 mc. Transducers at these frequencies are normally made in the form of thin quartz plates which are then bonded onto the medium in which the ultrasonic wave is to be propagated. The crystallographic orientation and geometry of these plates determines the type of wave generated and the way in which the efficiency of the electromechanical conversion varies with frequency. Analysis of the design parameters shows1 that the frequency of maximum efficiency (the fundamental or resonant frequency) is that frequency at which the transducer is approximately half the wavelength of the ultrasonic wave in the material. As the frequency increases, the ultrasonic wavelength, and therefore the optimum transducer thickness, decreases and in practice the fabrication of quartz transducers with fundamental freauencies above 100 mc becomes extremely difficult due to the extreme thinness required. For frequencies above 100 mc quartz transducers can be used in overtone-mode operation, and for very high frequencies (500 to 24,000 me) a technique using a quartz rod inserted in a high-Q microwave cavity4 is available. These techniques, however, exhibit comparatively low fractional bandwidths and rather poor conversion efficiencies. The present trend in ultrasonics is towards high frequencies and greater bandwidth to allow the use of shorter pulses which can give increased discrimination in radar-system delay lines and greater storage capacity in computer applications. The increasing demand for more efficient transducers with greater bandwidth

Jan 1, 1964