Search Documents

By J. B. Austin

In considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these efficiencies are more useful than others, yet all are instructive; for a knowledge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermodynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By William E. Ford, Edward Salisbury Dana

A. Hexagonal Division 1. Normal Class (13) Beryl Type 2. Hemimorphic Class (14) Zincite Type 3. Pyramidal Class (15) Apatite Type 4. Pyramidal-Hemimorphic Class (16) Nephelite Type 5. Trapezohedral Class (17) B. Trigonal or Rhombohedral Division 1. Trigonal Class (18) Benitoite Type 2. Rhombohedral Class (19) Calcite Type 3. Rhombohedral-Hemimorphic Class (20) Tourmaline Type 4. Trirhombohedral Class (21) Phenacite Type 5. Trapezohedral Class (22) Quartz Type 6. Other Classes (23) 7. Other Classes (24) Mathematical Relations of the Hexagonal System 119. The HEXAGONAL SYSTEM includes all the forms which are referred to four axes, three equal horizontal axes in a common plane intersecting at angles of 60") and a fourth, vertical axis, at right angles to them. Two sections are here included, each embracing a number of distinct classes related among themselves. They are called the Hexagonal Division and the Trigonal (or Rhombohedral) Division. The symmetry of the former, about the vertical axis, belongs to the hexagonal type, that of the latter to the trigonal type. Miller (1852) referred all the forms of the hexagonal system to three equal axes parallel to the faces of the fundamental rhombohedron, and hence intersecting at equal angles, not 90". This method (further explained in Art. 169) had the disadvantage of failing to bring out the relationship between the normal hexagonal and tetragonal types, both characterized by a principal axis of symmetry, which (on the system adopted in this book) is the vertical crystallo raphic axis. It further gave different symbols to faces which are crystallographally identical. It is more natural to employ the three rhombohedra1 axes for tri- gonal forms only, as done by Groth (1905), who includes these groups in a Trigonal Syslem; but this also has some disadvantages. The indices commonly used in describing hexagonal forms are known as the Miller-Bravais indices, since the were adopted by Bravais for use with the four axes from the scheme used by Miller in the other crystal systems.

Jan 1, 1922

THE problem of reaction rates in the open-hearth process is essentially that of trying to form a fairly clear picture of the "chemical mechanisms" in the bath. Quantitative data on reaction rates would not be very useful even if they were available; however, what few , approximate data there are, can be used in combination with data given in Chapters XVI and XVII to sketch a picture of the "chemical mechanics" of the open-hearth process that is consistent with essentially all the present available evidence. The result may later be found incorrect in many details but even so it will illustrate certain useful methods for obtaining a clearer understanding of the process. As discussed in the last portion of Chapter XIII chemical reactions in general involve the following factors: 1. The reacting molecules are mixed together in space in such fashion as to favor collisions among them. 2. A certain number of collisions occur per unit time among the reagent molecules, depending on their concentration and on temperature. 3. A certain percentage of these collisions result in reaction, these being the collisions between those molecules possessing at the moment energy levels above certain minimum values. The temperature factor enters mainly through (3), and its effect is very marked. (What is called temperature is really the mean energy content of all the molecules of the substance involved; at any one temperature a certain proportion of the molecules will have much higher energy content than the mean value.) Various reaction rates measured at around room temperatures have been found to be speeded from 1.6 to 4.0 times by an increase of only 15 to 20°F., simply because increasing temperature produces a rapidly increasing percentage of molecules with energy levels above the minimum needed to produce chemical reaction in a collision.

Jan 1, 1944

By John R. Gould

A mathematical treatment of multiple-pass floating-zone refining of semiconductors, including the evaporation of solutes from the melt at reduced pressure, is presented. Vapor pressures and evaporation rate constants for phosphorus, arsenic, and antimony in germanium have been determined from floating-zone experiments conducted at 10 mm Hg. Rate sensi-tivity of arsenic in germanium has been examined over the range of 1 to 10 in. per hr growth rate. The equilibrium value of the segregation coefficient of arsenic in germanium, as determined by an extrapolation of these data, was found to be 0.09. PFANN has treated the segregation of nonvolatile solutes in the zone-melting process, Bradshaw and Mlavsky2 considered the evaporation of solutes in a vacuum during the growth of crystals by pulling from the melt, and van den Boomgaard3 has shown that it is possible to bring a volatile impurity element homogeneously into an ingot by means of zone-melting under a constant pressure of that element. This paper is concerned with the volatilization of solutes during zone - melting in a vacuum. The mathematical analysis by Lord4 of multiple-pass zone melting is extended to include evaporation of solutes. A method is presented in which evaluations of vapor pressures, evaporation rate constants, and distribution coefficients may be derived from the variation of solute concentration in the floating-zone refining of germanium at 105 mm Hg. EXPERIMENTAL Ingots of zone refined germanium, approximately 1/4 in. in diam and 10 to 12 in. in length, were subjected to several floating-zone passes at 105 mm Hg in order to provide intrinsic material for these studies. These ingots were then seeded in a [Ill] direction and solid-doped to a constant impurity concentration of approximately 1015 atoms per cmS in a forming gas ambient (10 pct H - 90 pct A) at 1/2 atm gage. The resulting crystals were subjected to repeated floating-zone passes at 105 mm Hg and a concentration profile along the length made after termination of each pass. Concentrations were determined from four-point probe resistivity measurements, and proper precautions were taken to prevent contamination during handling. A constant zone length, crystal cross section, and growth rate were maintained during zoning. A stationary coil and moving crystal system were employed for floating-zone growth with neither the section of crystal above nor below the melt rotated.

Jan 1, 1962

By J. E. Lawver, J. L. Wright, H. R. Kokat

Mesabi semitaconite and oxidized taconite ores that cannot be concentrated by froth flotation can be rendered amenable to flotation through partial concentration in a high-in tensity wet magnetic separator. Since 1964, a method for accomplishing this precon-centration has been under development at the Minnesota Mines Experiment Station, where several hundred tons of ore have been successfully processed. This paper is an analysis of the performance of the separators used at the Station. At present the United States is producing about 85 million tons of iron ore a year, and nearly 55 million tons of this comes from Minnesota. Nearly half of Minnesota's production is in the form of magnetite taconite pellets —the remainder being wash ore and gravity concentrates. As the demands of the blast furnace operators become more stringent - and they are becoming more so yearly — these demands are met by improved iron ore beneficiation technology. Furthermore, there is no doubt that as magnetite taconite, gravity ores, and wash ores are exhausted, new processes will be developed to produce a product comparable to magnetite taconite pellets from Minnesota's vast reserves of oxidized taconite and semitaconite. The magnetite taconite ores are rather easily bene-ficiated by conventional, low-intensity (500- to 1400-gauss) magnetic separators, followed, in some plants, by froth flotation of the magnetic concentrates.

Jan 1, 1969

By William Marsh Baldwin, T. S. Howald, A. W. Ross

The related subjects of preferred orientation, directionality in physical properties, and earing tendencies of wrought metal strip have attracted the attention of metallurgists to such an extent that in the past 20 years hundreds of researches have been published on this one general problem. The anisotropy of tensile strength and elongation have been exhaustively studied in their relationship to the occurrence of ears in cups drawn from strip'-~O.~g and, to a lesser extent: yield strength7."-l7 and stress-strain curves'5 have been investigated. Despite the tremendous fund of knowledge thus accrued, no simple quantitative correlation of directionality and earing tendencies has yet been found. In a sense, this is not surprising. The formation of ears in a drawn cup clearly is a special phase of the general study of metal flow; in particular (as will be brought out in the course of this paper), ears are due to anistropy in the rates of deformation of the metal in the radial, circumferential, and "thickness" directions of the original blank. It would be difficult to effect a correlation between caring tendency and a property that may be completely independent of the flow of metal, or at best related to metal flow in an exceedingly complex fashion. Yet, it is this correlation that has been attempted; tensile strength and elongation are attributes of metal rupture. a phenomenon that has quite admirably been shown to be distinct from the phenomenon of metal flow,21 while yield strength and stress-strain

Jan 1, 1946

By A. W. Demmler

RECENTLY, Chaudron,&apos; Montariol,2 and their co-workers published the results of their studies on zone-refined aluminum. They found their material to be capable of recrystallization at —50°C, but gave no data as to the percentage reduction or time required. Their material was found to be practically non-work hardening at room temperature, but after 96 pct cold work at a low temperature and storage in liquid nitrogen it was found to recrystallize to coarse grains in less than 3 hr at 20°C. Recently, a study was made of the room temperature recrystallization characteristics of zone-melted aluminum. An ingot 14 in. in length, with a 3hx3 in. cross section, was made in an extremely high purity graphite boat under an atmosphere of dried commercial argon. It was made by first passing the molten zone along the ingot of 99.99+ pct A1 15 times. At this point, the most impure 3 in. (the end toward which the eutectic forming impurities migrated) were replaced with more of the original starting material, and 15 more traverses were made. Each traverse of the zone along the ingot required approximately 3 hr. Three ingots were prepared in this identical fashion and the chemical analyses were made spec-trographically on two of these ingots, rather than on the one used in this investigation. The analyses were made at 1 in. intervals along the ingot, in duplicate. Over the purest 5 in. of the ingot, which were most important in this investigation, there was found an average composition of <0.00004 pct Cu, <0.0003 pct Fe, <0.0001 pct Si, and <0.0001 pct Mg. In addition, the following elements were not detected spectrographically even in the more impure end of the bar: manganese, zinc, nickel, chromium, titanium, vanadium, lead, tin, boron, beryllium, bismuth, gallium, zirconium, cadmium, antimony, cobalt, and molybdenum. The original ingot was given several cold reductions, with intermediate anneals in order to refine the grains. Owing to the extreme length resulting and the ease of deforming the material plastically, it was cut into eight equal lengths and identified as shown in Fig. 1, with the highest numbered section at the purer end (that enriched with peritectic formers). Section 6 was used in the exploratory work and was found to be of exceptionally high purity, giving more rapid rates of room temperature re crystallization than any previous aluminum studied at the Alcoa Research Laboratories. This fact suggested that the entire midsection of the ingot might be of very high purity. Accordingly, section 4 was chosen for the next study. A portion of it was rolled to cold reductions of 10, 25, 40, 60, 75, and 90 pct at room temperature, and the re-crystallization of each specimen was followed by X-ray pinhole transmission photographs. The other portion received the same treatment, except that both the specimens and the rolls were maintained at 160°F in the process of rolling. The latter ortion was retarded in its recrystallization as compared to the former, probably due to the stress relief effect of the warm rolling. Both of these portions of the fourth section were found to recrystallize at a considerably slower rate than did the sixth section.

Jan 1, 1957

By P. S. Rudman

The solubility limit and the diffusivity of carbon in molybdenum have been obtained by duffising carbon into molybdenum rods from a Mo + Mo2C powder mixture. The solubility limit was taken as the long-time asymptotic limit of the rod composition. The diffusiv-ity was obtained from fractionally saturated rods from the rate of change of the average composition. Compositions were determined by chemical analysis. The solubility limit obtained is: WhILE the Mo-C system is important in refractory alloy technology neither the solubility limit nor the diffusivity of carbon in molybdenum is unambiguously known. In Fig. 1 the Mo-C phase diagram is presented. The heavy lines, the terminal solution solubility limit, and the eutectic temperature are results of the present investigation and will be discussed in detail later. However, it is readily seen that the previously published solubility limit determinations, Few and Manning1 and Fromm and ROy2 differ by up to an order of magnitude. The general form of Fig. 1, the Mo2C field, and a eu- tectic temperature -2200°C are due to an early Investigation by Sykes et a1.3 Although they did not determine the solubility limit, they did establish that the maximum at the eutectic temperature was about 1000 ppm. The only other prior data found on the solubility limit is from a lattice-parameter study by Speiser et a1 .,4 from which it can be concluded that the maximum solubility is greater than 1800 ppm. There does not appear to be any data oh the diffusivity of carbon in molybdenum. However, Samsonov and Epik5 have determined, from the rate of growth of an MozC layer, the diffusivity of carbon in Mo2C, and this has been erroneously interpreted, for example by ~c~eil,&apos; as applicable to diffusion of carbon in molybdenum.

Jan 1, 1968

By Donald Ingvoldstad, Harold E. Lee

AT Bunker Hill the original charge storage and preparation system was installed in 1917 to accommodate lead-silver gravity mill products. Only minor tonnages of wet fines such as vanner and flotation concentrates were received. Charge flux and diluent requirements were .provided by an ample supply of siderite middlings and coarse lime-rock. While oversize material was crushed through ¼in., the use of roll crushers in series resulted in a more or less granular, free-running charge of adequate porosity. Under such conditions, receipts could be proportioned directly from receiving bins, and suitable blending was obtained by passing the resultant layered composite through a small Stedman disintegrator. This elementary system served well for production and smelting of an extremely lead-rich sinter, in the low column blast furnace. Here sinter physical quality is less critical, and appreciable quantities of raw flux and oxidized ore may be charged directly to the blast furnace without seriously impairing furnace capacity. Prior to 1938 the relative proportions of zinc receipts were low and extraneous flux requirements at a minimum. However, subsequent war-inflated zinc demands brought marked increase in fine concentrate and slimy zinc leach residue receipts and an abrupt introduction to smelting a more refractory zinciferous charge. The higher temperature demands of the more refractory zinciferous charge required a higher smelting column and the higher column, in turn, rendered the blast furnace less receptive to improperly prepared feed. Inadequate presinter processing facilities prevented the production of acceptable sinter, and blast furnace production declined to 50 pct of former capacity. In view of a prevailing contention among lead metallurgists as to the deleterious action of high zinc slag on blast furnace capacity, it was natural to overstress this factor and to concentrate on possible changes in furnace design. Another interpretation was that primary correction should be sought through expanded sintering facilities. This divergence of opinion, together with the extreme material shortages of the 1940&apos;s, delayed corrective

Jan 1, 1957

By G. F. Comstock

A serious disagreement as to the effect of titanium on the hardenability of steel exists in published references to this subject. Kramer, Hafner and Toleman reported&apos; that acid-soluble titanium decreased creased the hardenability, with multiplying factors less than unity according to [ ] Grossmann&apos;s system for calculating hardenability from the composition. Crafts and Lamont, on the other hand, showed2 how titanium increased the hardenability, with multiplying factors up to nearly 1.7 for about o.&apos; per cent titanium, though reducing the hardenability with higher titanium. Their data, however, were obtained almost exclusively from steels containing more than 2.4 per cent manganese, and thus should be considered as applying mainly to manganese steels. Likewise, the results of Kramer, Hafner and, Toleman regarding titanium are subject to the limitation that although they eliminated the effect of the insoluble titanium compounds from their calculations, they did not make a similar correction for the carbon that was combined with titanium and therefore occurred in a similarly ineffective form. It is suggested by the literature referred to that titanium may have different effects on hardenability, depending on the mode of its occurrence in the steel. The different effects on strength, ductility, etc., have already been discussed by the author.3 In the present discussion some comparisons, on the basis of hardenability as revealed by the Jominy end-quench test, are given between three titanium and two non titanium steels heat-treated in the same ways, and between other titanium steels heat-treated in several different ways. COMPARISON OF PLAIN-CARBON, VANADIUM AND TITANIUM STEELS The five steels used for these experiments were commercially melted and rolled products received in the form of 1.5-in. rounds from three different mills. Their analyses are given in Table I. Steels 2, 3, and 4 are from the same basic electric heat, containing 0.009 per cent of phosphorus and the same amount of sulphur. They were made by, adding aluminum and low-carbon ferrotitanium to different ingots. No. I is a plain-carbon coarse-grained S.A.E. 1040 steel made by the basic open-hearth -process. No. 5

Jan 1, 1945

By J. J. Demo

The effect of aluminum additions on the coating vale and corrosion resistance of Cr-Fe diffusiou coalings on a mild steel substvate has been studied. Aluminum additions up to 2 wt pct increase the chromium penetration rate while further additions retard it. The apparent cor$lict between these data and metallogyapkic ineasurements, which show a continuially increasing coaling thickness with aluminum addition, is discrissed. Compavisorz of corrosion resistance on the basis of equal thickness of tlre entire coating measured mnetal- ALTHOUGH ferrous metal articles are cheap and widely used, they are often quickly degraded by corrosion. To prevent or slow down the corrosion process, lographically is misleading; equal thickness of the cor-rosion-resistant portion of the coating is a bette.v basis of conzpavison. Inter difision coefFicients for Cr-Al-Fe coatings of different aluminum content have been detevmined and found to dary logarithmically when plotted againnst chromium concentvation. A general method of calculating diffusion profiles for different lrealment limes and surfuce coucentralions IS described. many types of coating are applied to steel.&apos; Among these are diffusion coatings, formed by high-temperature diffusion of selected elements into the surface, which then becomes the coating Diffusion coatings are metallurgically bonded to the substrate and show a continuously varying concentration gradient from surface to substrate. Generally, these coatings have the advantage of adhering to the substrate upon deformation of the composite. Moreover, when chromium is one of the diffusion elements, a mild steel substrate

Jan 1, 1968

FOR four years your Committee has been engaged in the study of problems connected with the educational preparation of professional geophysicists. The present report represents the conclusions drawn from the investigations and deliberations undertaken since it was first organized. These studies have shown that the evolution of geophysics has proceeded along lines that differed from those marking the advance of classical geology. The latter science developed as a descriptive one, dealing with directly observable terrestrial phenomena, and the elementary, rational explanations that could be offered therefor. The fact that these phenomena were also chemical and physical in nature was seldom given more than passing acknowledgment. During the last half century, however, a new approach to problems of terrestrial phenomena has become of greater significance. This new attack has come through the sciences of physics and chemistry, as the people trained therein have investigated the facts of the earth as problems in their respective sciences. This development has been chiefly at the hands of European investigators, and European universities have long recognized it by establishing departments or institutions of geophysics. In the universities of North America, their arbitrary departmentalization into fields of physics, chemistry, astronomy, geology, etc., has prevented the academic recognition of such domains of science as geophysics and geochemistry. In consequence, the development of these subjects in the United States has been largely at the hands of nonacademic institutions, while the universities themselves are evidently in a state of confusion as to how the subject should be handled. In some places an attempt to teach geophysics is made in the physics department, in others in the geology department, in some in the engineering school, and occasionally as a cooperative effort; a Department of Geophysics is seldom found in North America. In some instances, proper academic planning has been precluded by interdepartmental jealousies, or by lack of appreciation of the significance of the subject. For the background upon which these conclusions are based, the reader is referred to reports previously issued or sponsored by your Committee. These reports are available from Institute Headquarters. The "First Report of the A.I.M.E. Mineral Industry Education Division&apos;s Committee of Geophysics Education, 1939," summarizes the replies received to question-

Jan 1, 1942

By Arthur Winslow

Location.—The Liberty Bell gold-mine is in the San Juan region, in the southwestern corner of Colorado. It is situated about 2 miles from the town of Telluride, near the summit of the Uncompahgre range, at the head of Cornett basin, at an altitude of 11,000 feet, and in a district of excellent record in the past and of great promise for the future. In the immediate vicinity are such well-known and important mines as the Smuggler Union, with a total production of over $12,000,000; the Virginius and Revenue Tunnel group, with a production of probably $5,000,000; the Tom-Boy, with a production of probably at least $3,000,000; the Japan, the Cimarron, and a number of others. History.—The first prospecting in this district is reported to

Jan 1, 1900

By Anson Hayes

THE quality of sheet and strip products made of rimming steel is closely related to the structure and chemistry of the ingots. The varia-tion in composition throughout the ingot, as affected by segregation, is of great importance, as are also the form and distribution of the voids that result from the gases evolved. It is because of this importance that the considerable literature in this field has accumulated. No attempt is made in the present paper to compile a bibliography of the excellent work that has already been done, as this has been adequately covered in the many excellent reports on the heterogeneity of steel ingots prepared by a joint committee and published by the British Iron and Steel Institute.1 From time to time, in any field of investigation new tools and new technique are developed, which make further progress possible. In the field with which this paper is concerned, this is true. The development of the vacuum-fusion method as a means of following oxygen segregation, and a technique for obtaining the volume and composition of the gases evolved during solidification, have opened the way to obtaining data by means of which some considerable progress has been realized in developing more of the detailed mechanisms of solidification and segregation in rimming-steel ingots.

Jan 1, 1938

By R. J. Borg, C. E. Birchenall

Vapor pressures of eight compositions of Mg-Cd have been determined by the Knudsen effusion technique. Measurements are made at several temperatures for each alloy and the results interpolated to a common temperature for the calculation of the activities. It is not possible to obtain values for the partial molar enthalpies because of the narrow temperature range spanned by the measurements. The results show less precision than those obtained for pure Cd which are also reborted. These alloys are extremely susceptible to corrosion which provides a possible explanation for the lack of precision. Nevertheless, the values of the activity are in good agreement with the results of electromotive force measurements previously reported for the Mg-Cd system. MAGNESIUM and cadmium are mutually soluble in all proportions in the solid state and form a single phase which has the hexagonal close-packed structure. X-ray investigations of this system1,2 have revealed a rapid variation in the relative dimensions of the unit cell occurring at approximately 50 at. pct. The rate of change of the c/a ratio with composition increases markedly for alloys containing more than 50 at. pct Cd. The purpose of this investigation was to determine the activity of Cd in the neighborhood of 50 at. pct and to discover whether or not the thermo-dynamic properties undergo a similar rapid change. The activities are calculated from vapor pressure data obtained by the Knudsen effusion method. Unfortunately the precision of the data from which the thermodynamic values are calculated is insufficient to establish unequivocally a departure from the normal trend. The results are reported primarily because they substantiate the only previously reported activity measurements3 and because they include values for pure Cd which in contrast to those of the alloys show excellent precision. The Cd-Mg system is known to contain several ordered phases. However, this investigation was made at temperatures considerably above the transition temperatures, and the alloys may be regarded as nearly random solid solutions. EXPERIMENTAL Apparatus—The effusion cells are machined from solid tantalum rod. The lids consist of threaded, flanged rings of tantalum onto which are welded shallow cups of 4 mil molybdenum foil. The orifice, which is located at its center, is made by grinding off a small dimple produced with a sharpened punch. Such an orifice has been mounted in plastic, sectioned, and the thickness of the orifice edge measured in a microscope. The maximum thickness is 0.00016 in., and the Clausing factor is consequently equated to unity. The area of the orifice is determined by tracing its projection on the screen of the metallograph at a known magnification and measuring the area of the tracing with a planimeter. Excellent temperature control is achieved with a 4 by 18-in. alundum core, gradient-wound, furnace

Jan 1, 1960

By C. W. Washburne

Recently, Messrs, Mills and Wells1 published a thorough chemical study of the waters associated with oil in parts of the Pennsylvania, Ohio, and West Virginia region. Many of their conclusions are of general application and the writer wishes to discuss some of these. Messrs. Mills and Wells show that the composition of the deep brines oi the Appalachian fields is such as would be produced by the evaporation of sea water and the precipitation of sodium chloride, combined with reactions with hydrocarbons and other substances. The brines are altered, also, by considerable mixing with meteoric water. They give good reasons for believing that the concentration of the brines was produced by evaporation in the rock pores induced by migrating gas, much of which probably escaped to the surface of the ground. This hypothesis was considered by the writer in a former paperJ2 in which main stress was laid on a second hypothesis, that the excess of chlorine in the deep brines may have been due to the entrance of solutions rich in magnesium and calcium chloride which ascended from a deep, possibly intratellurie, source. Messrs. Mills and Wells present good arguments for the first hypothesis. Underground evaporation by ascending gases probably will be accepted as the best available explanation of the concentration and composition of deep well waters. They have not considered the possibility that salt waters in deep sands may be concentrated by the diffusion of water vapor through gas into shale. The writer has given reasons3 for believing that capillary forces concentrate gas and oil in the larger openings of rock, such as the pores of sandstones embedded in shale. The gas underground must be nearly saturated with water vapor at all times, because it always is in contact with the interstitial water of enclosing shales and of the sandstone. Experimental studies of soil moisture have shown that approxi-

Jan 1, 1921

By G. Derge, M. Bourgon, G. M. Pound

A STUDY of electrical conductance in molten Cu-Fe sulfide mattes&apos; has shown that pure molten Cu,S behaves like a semi-conductor in that it is an electronic conductor and its specific conductance, of the order of 100 ohm-&apos; cm-&apos;, increases with increase in temperature. On the other hand, pure molten FeS, another electronic conductor, behaves like a metallic conductor in that its specific conductance, about 1500 ohm-&apos; cm-&apos;, decreases with increase in temperature. Molten solutions of Cu,S and FeS follow a roughly additive rule of mixtures with respect to both specific conductance and temperature coefficient. The behavior of molten Cu,S may be understood, by analogy to the situation in solids, in terms of semiconductor theory.&apos; It is thought that, although the melt consists of cuprous and sulfide ions, the bond between these atoms has a certain degree of cova-lency. According to the simplest concept the electrons in the partially covalent bonds are thermally promoted to a conduction band. In another concept, small amounts of impurities (undetermined) provide donor or acceptor levels in the forbidden zone between the valence and conduction bands and thus facilitate semi-conduction in the usual way. However, the metallic behavior of molten FeS is difficult to explain, because one might expect from similar reasoning that it too should act like a semi-conductor. It was suggested that the apparent metallic behavior of molten FeS might be explained by a large negative temperature coefficient of density. Thus if molar conductance instead of specific conductance were plotted versus temperature, the slope might prove to be positive, indicating semi-conduction instead of apparent metallic conduction. Accordingly, density measurements were made in order to answer this question in regard to molten FeS and also to provide data for conversion of specific conductance to molar conductance for molten Cu,S and a molten 50-50 wt pct Cu-Fe sulfide matte. Experimental Diagrams of the apparatus are given in Figs. 1 and 2. A 3 x 8-cm dense alundum crucible containing the prefused specimen is positioned in the uniform temperature zone of an induction furnace tube and melted under a helium atmosphere. Then the cell assembly, consisting of two 3-mm spectro-graphite rods, one of which is in a 1-cm ID open

Jan 1, 1959

By Carl R. Davis, J. L. Willey, S. E. T. Ewing

The first tube-mill on the Rand was put into operation in May. 1904, at the Glen Deep Mine. From that time onwards, tube-mills were added to various plants, although little was known regarding the capacity of a given tube-mill when working on banket ore. Within a few years, however, the so-called standard size (length of shell, 22 ft. 0 in.; diameter, 5 ft. 6 in.) was generally used until the last year or two. Practically the only exceptions were about 30 tube-mills having a length of 16 ft. and a diameter of 6 ft., and a few open-end mills of the roller-supported type. Most of the information obtained during the last 15 years has been obtained with mills of the standard dimensions. The adoption of the tube-mill as an accessory to the stamp mill was rapid; and where 3 tube-mills were working on the Rand at the end of 1904, 244 were in use seven years later.&apos; By 1910, good practice provided 1 tube-mill for 20 stamps of 2000-lb. falling weight. The horsepower of the motors driving the tube-mills had increased from 80 to 100 and then to 125 at this date. Broadly speaking, current practice at that date aimed at a ha1 product of which 60 per cent. was suitable for sand treatment and 40 per cent. for slime. The sand grading was +60 mesh, 6 per cent.; +90 mesh, 25 per cent.; — 90 mesh, 69 per cent.; and the slime grading +200 mesh, 2 per cent.; —200 mesh, 98 per cent. It was recognized comparatively early that the tonnage of — 90-mesh product produced by a tube-mill per 24 hr. was a convenient measure of

Jan 1, 1925

By Albert Sauveur

AT the New York meeting of the Institute, February, 1914, Professor Hopkinson and Sir Robert Hadfield presented an important paper entitled Research with Regard to the Non-Magnetic and Magnetic Conditions of Manganese Steel.1 Any contribution on manganese steel by its discoverer necessarily carries with it much weight and is entitled to serious and close consideration. The momentous discovery of that alloy by Sir Robert Hadfield some 30 years ago was the signal for great activity in the field of alloy steels; and the remarkable results obtained in the last two decades probably constitute the most important modern advance in the metallurgy of steel. The authors of the paper referred to above are unable to reconcile with the allotropic theory the interesting results obtained by them in heat treating manganese steel. When they speak of the allotropic theory, however, I understand that they have more especially in mind the existence of beta iron. It is not my understanding that they question the occurrence of iron in the two allotropic varieties known as gamma and alpha. If I am wrong, I trust they will correct me. A careful consideration of the experimental results reported and discussed by the authors leads me to believe that on the contrary they can be very satisfactorily explained in terms of allotropy and that, in the light of our present knowledge, they cannot be accounted for in any other way. The physical properties of non-magnetic manganese steel described by the authors are those pertaining to iron-carbon alloys in which iron is present in the gamma condition, or, in other words, to austenite. The metal is then characterized by great tenacity and ductility and low elastic limit, while its hardness, mineralogically speaking, is not excessive, but of a special kind termed "tough hardness" by the authors. Even when subjected to the restraining influence of a large amount of manganese and of considerable carbon, however, relatively rapid cooling

Jan 9, 1914

By George J. Young

DURing the spring of 1910 1 visited a number of open-pit brown-coal mines and underground workings in the vicinity of Halle, Halberstadt, Leipsic, Cologne and Bonn. The notes which I took and the observations which I made at the time have been condensed and make up the principal part of this paper. Certain supplementary information has been taken from several sources which are given in the paper. The mining of brown coal is one of the important industries of Germany. The coal varies in color from dark brown to almost black and is soft like loam. Pieces of wood and strips of bark and even parts of tree trunks are frequently encountered in the excavation although the coal for the most part consists of a pulverulent, more or less matted mass of small particles of vegetal matter. It is a product between peat and lignitic coal. An analysis, taken from Coal Resources of the World shows the approximate composition of the material: Moisture, 53.73 per cent.; ash, 4.98; fixed carbon, 18.08; volatile carbon, 23.31 per cent. Thc principal characteristic is the amount of moisture. This seldom runs less than 48 per cent. The ash is usually low and ranges from 5 to 10 per cent. The sulphur content is usually less than 0.5 per cent. The heating effect of the fuel ranges from 2,000 to 2,500 calories. The commercial deposits are confined to the Tertiary period although

Jan 1, 1916