Search Documents

By W. A. Backofen, D. Lee

Titanium of commercial purity (RC-70) and two all-a (hcp) alloys (4Al-1/4O2 and 5Al-2.5Sn) were tested in sheet form under conditions of combined-stress loading. Plane-strain compression and plane -strain tension together with uniaxial compression and tension provided information for constructing the tension-tension and compression-compression quadvants of the plane-stress yield locus. Coordinate values were obtained from yield-strength measurements; the slope at each point was based on a plastic-strain ratio. The materials represented a wide range of plastic anisotropy, which was reflected in correspondingly varied departures of the yield locus from that for iso-tropy. The tension-tension and compression-compression quadrants were not identical. If the uniaxial yield strength is insensitive to direction and the sign of the applied stress, the Mises or perhaps the Tresca criterion is adequate for predicting the onset of yielding under combined-stress loading. The prediction is not so straightforward in plastically anisotropic material. Depending upon details of texture, combined-stress yielding resistance may be substantially different from that indicated by the usual criteria.' However. a continuum theory of yielding under such conditions is available for reasonably direct application.2,3 Whether or not it can be used successfully must, of course, depend upon how closely the conditions of the theory are satisfied in the material in question. In its present form the theory contains no provision for Bauschinger-type effects, nor does it allow for the consequences that might grow out of deformation by more than one mechanism, e.g., by slip and twinning.4 With those limitations, more importance must be attached to experimental information about the yield surface for anisotropic materials. Studies of the yield surface have generally been confined to states of plane stress (tension-tension and tension-compression) established in thin-wall tubes by externally applied forces and internal pressure. That approach would be entirely suitable for anisotropic materials if they were available in tube form or in sufficient bulk to be machined into test specimens. 6-9 It would not serve for the textured and anisotropic sheets of much current engineering interest, unless sheet could be formed into high-pressure tubing without structural change. Since there would seem to be little chance of the latter, practical alternatives are needed. One such alternative is the subject of this paper. It involves the use of a few selected but relatively simple uniaxial loading tests on sheet specimens. The underlying idea is presented here with some details relating to application and a few results bearing on how well it has worked. THE BASIS OF TESTING Conventional Measurements. Yielding for a general case of anisotropy is described by the plane-stress locus in Fig. 1. Reference directions in the sheet specimen are related to the stress coordinates as shown with the insert: x is the rolling direction, y the transverse direction, and z the through-thickness direction. The four reference-direction yield strengths (t, tension; c, compression), Xt, Xc, Yt, and Yc, are all different. Nine paths that can be followed in uniaxial loading experiments are identified. Paths 1, 2, 3, and 4 represent conventional tension and compression testing to establish Xt, Yt,.Xc, and Yc. Useful information also comes from the ratio of the transverse plastic-strain components associated with yielding and flow in conventional tension or compression. A condition to be satisfied in locus construction is that the plastic-strain vector be everywhere normal to the locus.10 The projection of the vector which would

Jan 1, 1967

By Y. Shimomura, M. Serizawa, Y. Takahashi, K. Miyagawa

The "semi-pellet" sintering method developed and currently being used at the Fuji Iron & Steel's Hirohata Works is discusssd. It is shown that the method makes fine-sized material easily sinterable and increases sinter production. The operation can be incorporated readily into conventional sintering plants. Sintering plant raw materials currently being used in the Hirohata Works consist of 40 pct pyrite cinder, 40 pct fines resulting from crushing and screening of imported ores, and 20 pct others, such as mill scale and iron sands. Pyrite cinder, a major component in the sinter feed, has been getting finer since 1952, due to the increased grinding required for the improvement of the results in the iron sulfide flotation and to the adoption of FluoSolid roasters in sul-furic acid plants; some fines pass 100-mesh sieve almost completely. Increased use of the fine-sized pyrite cinders in the sinter raw mix resulted in such difficulties as decreased bed permeability, uneven firing conditions, and low yield. In an attempt to study the cause and to find a remedy for this problem, a series of experiments were made, using an 80-kg experimental sintering pan. As a result it was established that, by rolling the fine-sized pyrite cinders into small balls of 10 to 3 mm diam (hereafter called semi-pellets) and mixing them into the sinter raw mix, the bed permeability was improved, the sintering time shortened, and the yield and production rate increased. It is proposed that this new method be called the semi-pellet sintem'ng. In recent years the pelletizing process has taken the spotlight in the agglomeration field for treating fine-sized ores here in Japan as well as in the U.S. and Europe. This process produces pellets suitable for the blast furnace charge as such, and consists of three major operations: fine grinding, balling, and firing. With regard to the firing technique, some problems still appear unsolved. In the semi-pellet sintering, however, several ad- vantages can be claimed: the balling operation is relatively simple because only small-sized balls are shown to be acceptable and the operation can be readily incorporated into the conventional sintering plant, since only balling, not grinding or firing, equipment is needed. Basic test work on the process was initiated in 1954 and favorable results were obtained. Accordingly a pilot plant was built in 1955 and the test work was continued. The semi-pellets thus prepared in the pilot plant were tested further by USing them in the actual sintering pan and their beneficial effects ascertained. In late 1956 a drum-type balling machine (2.4X4 m) was installed and it went into operation in April 1957 in conjunction with the Greenawalt sintering plant (8 pans having dimensions of 7.2 m in length, 3 m in width, and 0.3 m in depth). In October 1958 a cone-type pelletizer, with a 2.2 m diam, and later a disk-type pelletizer were further added in the plant. In the DL sintering plant (2000 tpd), newly built in July, 1960, four disk-type pelletizers (3.2 m diam, 10 tph capacity) were installed. By mixing the semi-pellets thus prepared with the feed, the sintering operation was found to be greatly improved. The results of the basic test work, and the equipment and operation of the semi-pellet sintering operation at the Hirohata Works will be described. ON THE SINTERING CHARACTERISTICS OF FINE SIZED PYRITE CINDERS To ascertain the effect of addition of fine-sized pyrite cinders on the sintering characteristics, a series of measurements on bed permeability was carried out by varying the size distribution of pyrite cinders. The composition of the raw mix used in the tests was fixed at 50 pct pyrite cinder, 20 pct Larap magnetite fines, 30 pct sinter return, and 5 pct coke; only the size distribution of the pyrite cinder was varied. Also the moisture content was changed at each size distribution. The results are given in Fig. 1. For all pyrite cinders tested the bed

Jan 1, 1961

By K. E. Gray, G. M. Myers

In previous publications,5 results of single-blow bit tooth impacts on saturated rocks at various stress states were reported. This paper extends these earlier works to include study of bit impact tests on salt water-saturated Berea and Bandera sandstone samples under conditions of elevated confining and pore pressure. During the tests dynamic filtration and deposition of a mud cake were occurring due to the presence of drilling mud in the borehole and a borebole-to-formation pressure differential. Results indicate that saturation of these sandstones with salt water tends to make them weaker than when saturated with nonreactive fluids. Plastic failure often occurs even when extremely high fluid-loss muds are present in the borehole. The failure mode tends toward plasticity with decreasing fluid loss. Brittle failure of sandstones in mud-filled holes is apparently relatively rare. Depending on the stress level, and the associated failure mode, withdrawal of the bit tooth induces a tensile force that seems rather important relative to the quantity of rock removed by vertical tooth impact. INTRODUCTION A vast majority of the oil wells drilled today involve the use of colloidal muds having a measurable mud filtrate loss. It is known from field experience that reduction of the water loss of a mud generally results in a reduction of the penetration rate. This paper describes an investigation of crater formation at simulated bottom-hole pressure conditions for drilling fluids having different water losses. The literature on single bit tooth impact (cratering) at atmospheric conditions is extensive, but only a limited amount of work has been performed at the stress conditions similar to that found in oil wells. Spherical penetrator cratering tests on rocks at hydrostatic pressure were performed by Payne and Chippenda1e.1 Chisel impact studies on limestone with independently varying overburden and borehole pressure and atmospheric pore pressure were reported by Garner, et al.2 Gnirk and Cheatham3 performed "static" penetrator tests on dry rocks at equal overburden and borehole pressures. Podio and Gray4 studied the effect of pore fluid viscosity at atmospheric pore and borehole pressures and varying overburden pressures. Their results illustrated the importance of fluid saturation of the rock. Yang and Gray5 reported single tooth impact tests on saturated rocks at elevated borehole, pore and confining pressures, but with equal pore and borehole pressures. For the work reported in Refs. 4 and 5, filtration across the hole bottom purposely was avoided. Maurer6 has investigated the effect of independently varying pore and borehole pressures at elevated overburden pressures by using a zero water-loss mud in the borehole. His tests were carried out under conditions that allowed independent control of overburden, pore and borehole pressures, but without control of filtration at the hole bottom. EXPERIMENTAL APPARATUS AND PROCEDURE APPARATUS The single blow chisel impact apparatus used by Garner,2 as modified for this study, is shown in Fig. 1. A cross section of the pressure vessel is shown in Fig. 2. Several pieces of auxiliary equipment were added to the original apparatus in order that the borehole and pore pressure could be applied in a manner analogous to the actual bottom-hole situation. The pore-pressure system included a filtrate volume-measuring transducer and had sufficient surge capacity to allow filtrate to be injected into the sample without significant changes in pore pressure at points remote to the borehole. The borehole-pressure system contained a cross connection to the pore-pressure system so that both systems could be pressured simultaneously. The borehole-pore pressure differential was applied rapidly by the use of a quick and full-opening valve. The operation of this valve triggered two industrial

Jan 1, 1969

By H. C. H. Darley

The influence of particle size and concentration on the development of chip hold-down pressure (CHDP) was studied in an apparatus designed to measure the change of filtration rate during the first second of the filtration process. CHDP is controlled by the "bridging" particles (i.e., particles in the 50 to 0.2 micron range), whereas filter loss is controlled by the colloid fraction. The results indicated that a fast drilling fluid with a low filter loss could be obtained if the concentration of bridging solids and the viscosity were kept very low. A novel group of drilling fluids, which we have named colloid emulsions, was developed to meet the above requirements. These colloid emulsions are made by dispersing art oleophilic colloid in oil and emulsifying about 5 per cent of this dispersion in water or a dense brine. Good results have been obtained in field trials with emulsions which use asphalt as the oleophilic colloid. INTRODUCTION In recent years it has been found that fast rates of penetration can be maintained in hard formations by using "clear" water as a drilling fluid. In some cases, however, water cannot be used because the very high down-hole filter loss creates various difficulties in drilling, in logging, or in producing the well. It then becomes necessary to "mud up", which results in a decrease in drilling rate. The reason that mud decreases drilling rates is a complex subject which has been well covered by such authors as Garnier and van Lingen, Cunningham and Eenink,' and van Lingen.3 One of the principal factors involved is the tendency of the drilling fluid to develop a filter cake on the bottom of the hole. The pressure differential which develops across this filter cake opposes the action of the bit in dislodging chips from the rock. This pressure differential is referred to by Garnier and van Lingen' as the chip hold-down pressure, which is denoted by the initials CHDP in this paper. The work described in this paper was undertaken to develop a drilling fluid which would minimize CHDP but which would still have a low filter loss—in other words, a fluid which would deposit a filter cake on the sides but would lay little or no filter cake on the bottom of the hole. EVALUATION OF CHDP EXPERIMENTAL Conditions governing the growth of filter cake on the sides of the hole are obviously different from those on the bottom of the hole. On the sides of the hole, cake will form continuously but at a decreasing rate, until eventually the rate of growth will equal the rate of cake erosion by the mud stream.' On the bottom of the hole, each time a bit tooth dislodges a chip the cake is removed, a fresh rock surface is exposed, and the filtration process must start over again. Thus the CHDP is determined by the amount of cake which can form in the interval between successive tooth strikes at a particular spot, normally a fraction of a second. Our first step therefore was to study filtration rates over the first second or so of the filtration process. These tests were conducted in the simple type of dynamic filter cell shown in Figs. 1 and 2. In this cell the mud was filtered through a train of rock cores while rotating blades kept the mud flowing over the surface of the core. The procedure was to evacuate the cores to 0.05 mm of mercury, saturate with brine, and assemble in the holder under brine. The permeability of the core train was then determined. A plastic seal was placed on the face of the core train, and a rip cord was attached from the seal to one of the blades. At the start of the test, 500 psi was applied to the mud, and the meniscus in the capillary measuring tube was adjusted to zero. When the blades were started, t,he seal was ripped from the face of the core, and filtration began. The filtration rate was at first measured by photographing the advance of the meniscus in the capillary tube. Using

Jan 1, 1966

By Welton Crook

UNLESS present in considerable proportion, metals of the precious-metal group-other than gold and silver-are not readily detected by the methods of fire assaying usually applied to ores and metallurgical products. Platinum, when present in small quantity, will ordinarily be reported as silver unless special methods of parting are used. Other elements occurring in the gold itself are all fluxed and slagged in the assay operation and if analyses are made on bullions the melting and slagging operations to which the bullion has been subjected may eliminate most of the associated elements. On the other hand, the analysis of precipi-tate from the cyanide treatment of gold ores may reveal the presence of many unexpected elements, such as tungsten and molybdenum. It is uncertain, however, whether many of the elements present in the pre-cipitate are derived from the ore gangue or from the gold itself. No very general survey of the distribution of metallic elements in gold seems to have been made. Rose and Newman,1 in connection with the composition of native gold, say in part as follows: Gold is occasionally found alloyed with copper and sometimes also with iron, bis-muth, lead, mercury, tin, antimony, palladium or rhodium. Rhodium gold from Mexico was found to be of the specific gravity 15.5 to 16.8 and contained 34 to 43 per cent of rhodium. The native alloy of palladium, gold, and silver from Porpez con-tains 85.98 per cent of gold, 9.85 per cent palladium and 4.17 per cent silver. Mal-donite, from Victoria, contains gold 64.5 per cent, bismuth 35.5 per cent (Louis). Dana' says that native gold is usually alloyed with silver in varying amounts, and that sometimes it also contains traces of copper and iron. Rare varieties contain palladium, rhodium and bismuth. Other authors, for instance Zeigler3 and Clark,4 give similar information. Most refer-ences on the subject agree that ordinary native golds contain, in common, the elements silver, copper and iron. After completion of the work of which this paper is a record, the conclusion is reached that all ordinary native gold probably does contain these elements and, although in certain cases other elements may be found to be present, that it is difficult to

Jan 1, 1939

By G. W. Leney

Iron ores occur in such a wide variety of forms that nearly every kind of prospecting, geological knowledge, and geophysical technique has some application in the search for them. The type of orebody that is considered desirable depends on political and economic considerations, on transportation and markets, on the characteristics of the orebody, on the metallurgy of the ore, and on its comparison with other available ores. In North America, materials that can be efficiently processed into high grade concentrates and pellets are now the object of most exploration work. These are usually shallow, relatively unoxidized, metamorphosed iron formations that are particularly suitable for geophysical methods of exploration. Magnetic surveys are used for the direct discovery of new orebodies, for mapping stratigraphy and structure, and at times to locate oxidized zones in magnetic iron formation. Gravity mapping provides supplementary information, indicates gross tonnages, is useful in regional studies, and can discover non-magnetic orebodies. Electrical methods have not been fully exploited but self-potential, resistivity, applied potential, electromagnetic and perhaps induced polarization surveys all have restricted but highly useful applications. The use of all geophysical techniques promises to increase as the number of exposed easily discoverable orebodies decreases. A high consumption of steel, and consequently of iron ore is the chief characteristic of an industrial society and this consumption has been increasing at an average rate of about 35% every ten years for the past century. To supply this demand, iron ores and iron bearing materials in a wide variety of forms have been exploited on every inhabited continent and in nearly every country. Nearly every kind of prospecting, geological knowledge and geophysical technique has some application in the search for them. The type of orebody that is con-

Jan 1, 1964

By R. Sporcic, P. J. Mudra

During the past year personnel of the Roof Control Research Group of the Bureau of Mines designed and developed encapsulated hydraulic cells for measuring pressure changes in coal in situ. Preliminary results from feasibility tests in progress in the laboratory and field indicate that the cells respond favorably to changes in pressures associated with a coal-mining environment. The ultimate objective is to use these cells to obtain engineering information relating to coal bump or coal outburst phenomena. Mining research has experienced a remarkable growth during the past decade and from all indications should surge forward at even a greater pace in the future. This increased interest in mining research has been brought about by the ever-multiplying number of technical problems being encountered by the mining industry in its effort to produce pay-dirt tonnages safely and economically from greater underground and surface pit depths. Among the various divisions in the field of mining research, the study of ground stress has received a large part of the overall attention. Numerous technical papers have been written with regard to ground stress conditions around mine openings and yet the total usable knowledge concerning this subject is extremely limited. Research teams around the world are endeavoring to bridge the gap between theoretical and laboratory approaches and the solution to design problems in the field. The problem of ground stress is not a new one for the coal mining industry. Operators in both eastern and western coal fields of the United States as well as in many foreign countries have long been plagued with a number of ground stress problems, one of which is commonly referred to as the coal-mine bump. This term or phenomenon has been aptly defined by earlier investigators as the violent and sudden failure of coal and adjacent rock. Direct results of such failures have been the loss of human lives and thou- sands upon thousands of dollars of sustained mine damages. In an effort to alleviate the magnitude and frequency of these failures, mine operators have employed and are presently employing various corrective techniques. These include: Inducing failure in heavily stressed areas by augering large-diameter holes into stressed pillars, using extensively yield-able steel arches in both long-term haulage and short-term face entries, backfilling unused or abandoned entries with mine waste to gain additional support, and using systematic pillar coal panel extraction techniques including mechanized longwall mining. The Health and Safety Activity of the Bureau of Mines has for a number of years contributed considerable time, funds, and talent in an effort to define better the ground stress problems associated with coal-mine bumps. As a part of this investigative program, in situ ground pressures are presently being studied in coal mines located in West Virginia and Utah. The description and development of the device being used to measure these pressures is the specific topic of this paper. CHOICE OF INSTRUMENTATION After consideration and evaluation of the various instruments and techniques that are being used by researchers in the field of rock mechanics to detetmine in situ stresses, a simple hydraulic system was selected for detailed investigation. Aside from simplicity, a hydraulic system is relatively inexpensive and also eliminates the need for electricity in its installation and operation. The hydraulic device referred to is, in essence, a simple unidirectional pressure-measuring cell. Hydraulic cells, which had been used for measurement of pressures in hard rock, were investigated but found not entirely suitable for use in coal, particularly since they involved (1) preparation and emplacement of cement grout at the test site, and (2) a waiting period before the cells became operational. At the outset, it was decided that certain design parameters be established. The cell should be simple and inexpensive, constructed of materials readily obtainable and easily built in the laboratory or field by unskilled labor. It was further decided that it was desirable to encapsulate the cell in a suitable mate-

Jan 1, 1963

By C. Schlumberger

SINCE the, beginning of the year 1928 the senior authors and their associates have applied a series of procedures which makes possible the detailed study in situ of the formations traversed by a drill hole before the casing has been landed. They have given the name "electrical coring" to the ensemble of these processes, which now replace in a large measure the mechanical coring performed by the drillers, and permit the gathering of bottom-hole data hitherto unobtainable. Three years have elapsed since the technique and interpretation of these measurements emerged from the experimental stage and entered the field of industrial application on a large scale. The total length of drill holes so far surveyed by the authors and their associates, all over the world, amounts to several millions of feet. Practical and strongly built equipment has been evolved, which permits the examination in a short time of an open hole several thousand feet long. No comprehensive paper has yet been published discussing the essential principles of the processes applied and bringing into evidence their economic interest. This is the object of the present paper.1 Numerous examples of field work performed under varied geological conditions are given, constituting a concrete illustration of the services rendered by the new methods.

Jan 1, 1932

By M. W. Burkart, B. Lustman

Uranium-base alloys exposed to high temperature water fail either by uniform oxidation or by sudden cracking and disintegration of the metal. The disintegration results from the oxidation of a second phase which is precipitated during the corrosion process. The precipitate has been identified as a metastable hydride of uranium. URANIUM-BASE alloys consisting of the body-centered-cubic ? phase are susceptible to two different modes of corrosion failure when exposed to high temperature water. In the first process, a smooth oxide film is formed on the metal surface which continually flakes off during exposure and results in a uniform weight loss of the specimen. The oxide is present as a thin, adherent layer whose thickness remains approximately constant. As the metal oxidizes during corrosion, a nonadherent layer is built up on this film and continually sloughs off. Coincident with the uniform corrosion just mentioned, another process occurs which eventually leads to failure of the metal by cracking and general disintegration. The failure takes place during a relatively short time compared to the total exposure. To distinguish this type of failure from the uniform corrosion, the cracking or disintegration of the metal will be referred to as discontinuous failure. For the ? phase uranium alloys it is discontinuous failure rather than uniform corrosion that limits the useful corrosion life of the alloy. This paper will be concerned primarily with the mechanism of discontinuous failure. Physical Changes During Corrosion—The alloys used in this investigation were ? phase uranium alloys containing 7 to 12 wt pet Mo or Cb. The preparation of the alloys, the method of corrosion testing, and the actual corrosion results are presented in another paper.' The ? quenching treatment consists of annealing the alloy for 24 hr at 900°C in a sealed Vycor glass tube filled with helium and then water quenching to room temperature without breaking the tube. The corrosion behavior typical of a ? phase uranium alloy is shown in Fig. 1. This specimen was a U-12 wt pet Mo alloy tested in pressurized, degassed water at 650°F. The corrosion rate was practically constant at 0.28 mg per sq cm per hr or increased slightly until about 15 to 20 days of exposure, when the onset of discontinuous failure occurred in this particular sample, and the specimen soon began to crack and disintegrate. The simultaneous increase in the observed corrosion rate is a result of the increased area of exposure due to cracking of the specimen. The microstructure of a specimen that failed by cracking is shown in Fig. 2. The presence of a plate-like precipitate can readily be seen. Metallographic examination of corrosion specimens reveals that the onset of discontinuous failure is always preceded by the formation of a plate-like second phase in the ? uranium matrix. Hydrogen analyses of specimens periodically withdrawn from corrosion test reveal that the hydrogen content of the alloy increases on exposure to the high temperature water, as shown in Fig. 3. The hydrogen is available as a corrosion product resulting from the formation of UO2 by the reaction of the alloy with water. Specimens analyzed just prior to discontinuous failure contained as much as 1200 ppm H, whereas the plate-like phase appears to precipitate out at a hydrogen concentration of between 10 and 25 ppm. The observed increase in hydrogen content prior to and during the formation of the plate-like precipitate suggests that this constituent may be a hydride of uranium. Additional evidence linking the identity of this phase to a hydride is that it can be removed by vacuum annealing at temperatures of 100°C and above. Decomposition products of the ? phase would certainly not dissolve at such temperatures, nor could other likely products of corrosion, such as oxides, be dissipated at any of the test temperatures. The precipitation and growth of the second phase during corrosion is accompanied by an increase in hardness of the specimen. The hardness increase results from the dispersion of the harder precipitated

Jan 1, 1959

By R. W. Cahn, C. D. Graham

The rate of growth of a single grain growing into a strained aluminum single crystal, measured by the conventional heat-cool-etch technique, is shown to decrease with time at temperature. The growth rate measured by means of X-rays, with the sample continuously at temperature, is found to be linear. Evidence is presented to show that the decreasing growth rate obtained by the conventional technique is due to abnormal recovery in the strained grain, and that the recovery in turn results from the heating and cooling cycles, rather than from the effects of etching. The experimental apparatus is described in an appendix. FREQUENTLY, the rate of grain boundary motion during recrystallization is determined by heating a sample to a known temperature for a given time, cooling to room temperature, and etching to reveal the boundary position. The cycle of operations is repeated as many times as necessary to establish the rate of boundary motion. Although this heat-cool-etch technique has been used by a number of workers over a period of many years,'-!' other investigators have encountered difficulty with the method."'. " They have attributed the erratic results to the effects of repeated heating and cooling, or of etching, or both, and have adopted an alternative experimental procedure in which a number of identical samples are employed, each sample being cooled and etched only once. This alternative method ove1.comes some difficulties, but introduces others. In particular, the incubation periods of the observed grains are unknown: any effect of crystal orientation on growth rate cannot be determined easily. A preferable method would be to measure the motion of a recrystallizing grain boundary with the sample at temperature without etching," but such measurements have in the past been restricted to nonmetals. This paper describes the construction and operation of a device, the goniometer furnace, with which the position of a moving grain boundary between a recrystallizing grain and the strained single crystal into which it grows can be measured by means of X-rays, with the sample maintained continuously at temperature. Goniometer Furnace The operating principle of the goniometer furnace is shown in Fig. 1. The sample, in the form of a bicrystal strip, is surrounded by a furnace, not shown in the sketch, and can be rotated about the two axes A and B which intersect at the point where the X-ray beam strikes the strip. The strip is oriented so that one of the two grains gives a strong Bragg reflection, which is detected by a suitably placed Geiger-Miiller counter coupled to a counting-rate meter When the strip is moved parallel to its own length in the furnace, arrow C, so that the X-ray beam strikes the second grain, there is in general no strong reflection. By noting the position of the strip at which the drop in Geiger counter reading occurs, it is possible to determine the position of the boundary. Measuring the change in boundary position with time at temperature gives the rate of growth of the recrystallizing grain. Details of the construction and operation of the goniometer furnace are given in the Appendix. Measurements showed that the temperature in the furnace was uniform within ±10°C over its working length of about 28 cm. The temperature at the measuring position, i.e., at the point where the X-ray beam struck the sample, was estimated to be constant within ±2oC. Using the goniometer furnace, the position of a stationary boundary could be measured with a reproducibility of ±0.3 mm. At elevated temperatures, 500" to 625"C, with the boundary in motion and the X-ray reflection less sharp, the estimated accuracy of each measured boundary position dropped to about ±1 mm. Experimental Results The test pieces were single crystals of 99.6 pet A1 —principal impurities 0.19 pet Fe and 0.12 pet Si— 1 mm by 1 cm in cross section and 6 to 10 cm in length, grown by the strain-anneal method. This relatively low purity material was used because of the difficulty encountered in producing strain-anneal single crystals of very high purity—99.996 pet—

Jan 1, 1957

By M. Muskat, R. D. Wyckoff, H. G. Botset

The flow of liquids through porous media is known to follow Darcy's law which states that the velocity of flow is proportional to the pressure gradient. This law is but a statement of the facts obtained from experimental studies and is, therefore, uncontroversial. It should be men-tioned, however, that it applies only when the flow is viscous in nature and that at excessive velocities which tend to produce turbulence, the velocity is proportional to some power of the pressure gradient, the exponent ranging from 1 to 0.5 as the degree of turbulence increases. However., experiments with media having permeabilities corresponding to those of actual producing horizons show conclusively that the actual flow of liquids in a producing horizon must be viscous except perhaps in the immediate vicinity of a well producing at a high rate. Therefore, one is justified in assuming Darcy's law to hold for cases of practical interest, as will be implicitly assumed in this discussion Given this basic law of flow it is possible, theoretically to obtain solutions to any problem of viscous flow of dead liquids1 by the usual methods of potential theory. However, problems of practical interest often present such complex geometrical configurations of sources and sinks (driving sources and output wells) as to make the analytical solutions extremely difficult or even impossible. It is useful, therefore, to note that Darcy's law is precisely equivalent to the law of electrical conduction, so that the pressure distribution in steady state porous flow of liquids is exactly the same as the potential distribution in an electrical conducting medium.2 This analogy permits the use of electrical models wherein the potential distributions may be measured with far greater facility and accuracy than is possible in actual fluid-sand models. Such electrical models were used in determining the pressure distribution about complex arrays of wells, an example of which will be shown later in the discussion of the 5-spot flood. One phase of the porous flow problems which is of considerable practical interest involves the tracing of an advancing fluid front. Thus,

Jan 1, 1933

By C. R. Kyle, R. L. Perrine

A transparent model of a reservoir has been used to study some characteristics of instability in miscible displacement. The linear model dimensions are 1/4 in. x 91/2 in. x 10 ft. The model is packed with spherical glass beads. Thee groups of experiments have been performed. The objectives were to measure, respectively, the rate of growth of the transition zone, flow velocity variations in the transition zone, and the effect of a graded viscosity zone on stability. All experiments were compared, where possible, with theory. The transition zone grew almost linearly with distance traveled, regardless of flow rate, where adverse viscosity ratios were used. At very adverse viscosity ratios and large distances traveled, some reduction below linear growth was noted. This could be attributed to the effects of mixing. General similarity in flow pattern was commonly shown in different tests, although exceptions occurred at the higher viscosity ratios. Injection of tracer spots permitted direct experimental measurement of velocity variations. Statistical methods were used to compare observed velocity variations with recently published theories. Surprisingly good agreement with some theoretical predictions was obtained. In the experiments using an initially graded viscosity zone, macroscopic stability was reached before predicted by theory. Under conditions theoretically considered to be slightly unstable, any fingering tendency was too slight to become observable within a 10-ft long system. The general correlation of all experiments with published theory was good, and suggests that theoretical predictions can be extended to reservoir problems. INTRODUCTION Early laboratory studies of miscible displacement demonstrated the high recovery efficiency possible with this method. Linear laboratory models showed that, under some circumstances, all in-place hydrocarbons could be recovered using as little solvent as 5 per cent of the pore volume. These results led to a series of pilot field projects. Under realistic conditions, however, other laboratory studies showed that a small solvent bank may not recover much more oil than a conventional gas drive. The cause of this lack of efficiency is unstable viscous fingering. The size of the solvent bank required to give optimum recovery is, therefore, a question of great economic significance. The object of the experiments described in this paper was the quantitative measurement of unstable flow parameters, the verification of present theories on the miscible displacement process, and correlation of these theories with ex peri mental observation. Of the theories which have been advanced, those by Dougherty, Koval and Perrine show promise of predicting reservoir performance with reasonable accuracy.l-7 The present experiments were correlated, where possible, with the theories of Koval and Perrine. Dougherty's theory was not used because of the additional computational difficulty it presented and the belief that no further information would result. EXPERIMENTAL EQUIPMENT A transparent reservoir model, consisting of a vertical reinforced plexiglass column, was used for the experiments. The column was packed with glass beads, which served as the porous medium. To induce a known velocity disturbance in the flow, a double cosine wave restriction in the transverse cross-section was placed at the top of the column. To mark the flow field and provide a means of measuring the local fluid velocity, a dye-spot injection system was provided. The column was 10 ft high by 1/2 in. wide by 1/4 in. deep. The cosine restriction was placed 16 in. from the top of the column. The glass beads were smooth and spherical and had a mean diameter of 0.0102 cm. Liquids entered the top of the column through a manifold allowing three points of entry (left, center, and right, or any combination of these). A positive-displacement pump with variable-speed drive was used to control liquid flow rates. The pump transferred viscous oil from a reservoir to an accumulator, which displaced the test liquid into

Jan 1, 1966

By A. R. Marder

Fe-C alloys have been investigated at temperatures below the eutectoid transformation to determine whether the superplasticity phenomenon exists for these materials. As a result of void formation at the carbide-ferrite interfaces that led to void coalescence and premature failure, the large elongations characteristic of superplustic matem'als did not develop. It had generally been assumed that the conditions for obtaining superplasticity include: a) T/Tm =0.5, b) a strain rate sensitivity of the flow stress that results in m s 0.3, and c) fine-grain structure. Although superphsticity was not observed in the alloys studied, stress-strain rate measurements indicated that an additional condition for the existence of superplasticitv in Fe-C allovs is that the fine-wain structure be equiaxed in agveement with previous results on Zn-Al al1oys. MANY investigations have been made on the hot deformation of iron-base alloys in order to obtain an understanding of the variables that may affect high-temperature strength and ductility.'-6 However, only a few papers have studied the effect of carbon content on the high-temperature properties of iron-base alloys. Peretayat'ko and Zaikov and Wallquist and carlen4 studied the effect of carbon on strength in the y temperature range, and recently Robbins, Shepard, and sherby6 studied the influence of carbon on the torsional behavior of iron in the a and cu-plus-cemen-tite temperature ranges. In addition to studying hot deformation behavior, current investigations have also been concerned with the phenomenon of superplasticity in nonferrous materials, and, in particular, ferrous alloys. Superplasticity is identified by the increased resistance to necking that results from a high strain rate sensitivity of the flow tress. ackofenr proposed the strain rate hardening coefficient m = d log a/d log e as a measure of strain rate sensitivity and showed that m must be "-0.3 for superplasticity to exist. In addition, a fine-grained microstrcture,- a eutectic or eutectoid ornosition,- and a test temperature in the creep range (TITm > 0.5)" have also been advanced as necessary conditions for superplasticity. Although many workers""23 investigated superplasticity associated with the allotropic transformation in iron and the eutectoid transformation in steel, and recently chadler " and orrison have studied superplasticity in the a - y phase region, no one has measured the superplastic effect in the a + cementite temperature region. Therefore, the purpose of this investiga- tion was to determine the effect of carbon content, microstructure, and test temperature on the strain rate sensitivity of Fe-C alloys at temperatures below the eulectoid transformation. EXPERIMENTAL PROCEDURE Fe-C alloys with carbon contents of 0.2, 0.4, 0.6, 0.8, and 1.0 wt pct were prepared as 100 lb 54 in. ingots by vacuum-induction melting. The compositions are listed in Table I. All the ingots were soaked at 2100°F for 2 hr prior to rolling to 4 in. plate. The minimum finishing temperature for rolling was 1800°F. The plate was sheared in 10-in. lengths and tensile bars were rough-machined prior to heat treatment. The samples were heat-treated according to the schedule in Table I1 in order to obtain a fine-grained microstructure consisting of finely dispersed carbides in a matrix of small ferrite grains. All the tensile specimens were heat-treated prior to finish machining, and tensile testing was accomplished on an Instron machine in conjunction with a clamshell furnace. The buttonhead specimen configuration is shown in Fig. 1. An inert atmosphere, helium, was maintained during testing with a steel tube shroud in a bell jar arrangement. Predried helium was continually purged over the buttonhead specimens and exhausted through ceramic fiber at the bottom of the tube to keep oxidation at a minimum and to prevent

Jan 1, 1970

By W. R. Kube, W. H. Oppelt

Five low-rank coals, including two lignites, a steam-dried lignite, and two subbituminous coals, were carbonized at 940°F, in a bench-scale carbon-ize~ with a nitrogen and hydrogen atmosphere, or both, using pressures from atmospheric to 1000 psig. Coking characteristics were observed, and yields, composition, and distribution of products from thermal degradation were determined. The influence of pressure on yields from coal carbonization, as well as on modification of coke structure, has long been of interest. One of the first attempts at pressure carbonization was that of Capps and Hulett1 who in 1917 investigated the effects of pressure ranging from 1 to 20 atm on yields at 600° C for bituminous and subbituminous coals. High-pressure carbonization has not been used commercially for coke production. More recently, carbonization at relatively high pressure in the presence of catalysts and hydrogen has been proposed for the production of metallurgical-grade coke from low-rank fuels.' Another approach involves carbonization at high pressure in a hydrogen atmosphere to produce heating gas and a solid residue that is gasified with oxygen and steam to produce the hydrogen required for hydro-genation 3-4 or, alternatively, is burned to raise steam. Recently it has been proposed to carbonize coal under pressure, burn the gas in a gas turbine to produce power, and use the solid residue as fuel in a conventional steam-power plant.5 Our primary interest in pressure carbonization stems from an attempt to determine the influence of pressure on the coking characteristics of lignite to design a high-pressure slagging gasifier using oxygen and steam. At atmospheric pressure, North Dakota lignite is generally considered to be non-coking. However, lignite and subbituminous coals have been reported to show increased agglomeration properties in steam, hydrogen, or carbon-dioxide atmospheres at elevated pressures, although no strong coke was formed at pressures up to 3000 psig.6 If lignite would agglomerate seriously under gasification conditions, proper flow of charge through the gasifier could not be maintained without installing a mechanical stirring device or destroying the caking properties of the coal before gasification. Data on the caking properties of lignite or other gasification fuel, as well as on yields of products under conditions simulating the carbonization process in the pregasification zone, were required in the preliminary design stage of the gasifier. No information was available concerning the influence of pressure and type of atmosphere on North Dakota lignite. To provide this basic data, the U. S. Bureau of Mines investigated the effect of pressure and a hydrogen or nitrogen-rich atmosphere on the yield of products and on coke formation in a bench-scale pressure carbon-izer. SCOPE OF INVESTIGATION Five coals were tested at 940°F in nitrogen and hydrogen atmospheres, at pressures from atmospheric to 1000 psig. Yields and composition of solid, liquid, and gaseous products were determined as a function of the process pressure, and attention was given to the physical appearance of the solid residue. Percentage of carbon converted, sulfur retained in char, and thermal balances were calculated. In this paper, primary consideration is given to carbonization in a nitrogen atmosphere and to data concerning the solid phase. The effect of pressure in hydrogen is presented in detail for only one lignite. More complete information on the response of the other coals in a hydrogen atmosphere will be published in a USBM Report of Investigations. DESCRIPTION OF EQUIPMENT Details of the bench-scale pressure carbonizer are given in Fig. 1. The body of the carbonizer was

Jan 1, 1961

By A. J. Teplitz, R. J. Goodwin

A new type water shut-off for use in air drilling has been developed. The method has been 99 to 100 per rent effective in several different formations of inter-ranular-type porosity. Since costs for materials, time and equipment used are relatively small, the process should extend economies of air drilling to many new areas. The treatment involves a new technique for forming a water-inroluble precipitate within the pores of a rock. Advantage it taken of the difference in mobility of a liquid and a gas in porous media to achieve the greatest volume of precipitate in a given pore. Reactants selected for the laboratory (2nd field tests were aluminum sulfate solution and gaseous ammonia. This process has been tested in both intergranular and fractured-type porosities. It has consistently shut-of between 99 and 100 per cent of the water flowing from formations having intergranular-type porosity and perrlreuhilities ranging from a few millidarcise to over a darcy The treatment is not particularly suitable for shutting-off water from fractured formations although plugging of the order of 50 per cent or greater has been achieved in all such applications. Among advantages of the treatment are: (I) no reaction waiting rime after a relatively short placement time, (2) a low mate-rials cost of about $3/f1 of hole treated, (3) use of common service-type equipment for treatment, and (4) no unusual requirements for mixing and placement. INTRODUCTION In rotary drilling with air or gas it has been possible to increase bit life by tenfold and more than double rate of penetration over corresponding performance when drilling with mud. These factors have amounted to as much as 22 per cent savings on total cost of drilling a well. However, these advantages are rapidly lost when water is encountered in an air- or gas-drilled well because water interferes with the removal of cuttings from the hole and also gives rise to other difficulties. In attempting to combat water troubles, operators have commonly resorted to such measures as mist drilling, treatment with cement or chemicals, converting to conventional mud drilling, or setting casing. In many cases these measures have either been costly or ineffective. In an effort to overcome this problem, studies were undertaken to develop an effective and economical water shut-off technique for use in formations possessing inter-granular-type porosity. Extensive laboratory experimentation finally led to a unique method for producing a water-insoluble precipitate within the pores of a sandstone. The unique part of the treatment is use of a liquid and a gas to form the precipitate, and in this case the reactants used were aluminum sulfate solution and gaseous ammonia. The reaction between these two materials is shown in the following equation. Al2 (SO1)3 - 18 H20 6NH2? saturated Water- Solution Cat 2A1(OH)3 . n H20 3(NH4)2SO • n H20 Solid Solid That is, a solid precipitate consisting of aluminum hydroxide and ammonium sulfate is formed when ammonia reacts with aqueous aluminum sulfate. The aluminum hydroxide is insoluble in water and the ammonium sulfate, though soluble, can only be removed from the formation pores by diffusion—an extremely slow process. Although the precipitate formed by the reaction is not particularly firm, great strength is not needed for a precipitate to bridge and plug intergran-ular-type porosity. A flow path in such a system is extremely tortuous and involves a great variety of pore

By Oscar Glaeser

THE mine and plant of the United Verde Copper Co., located in Yavapi County, at Jerome, Arizona, have been described in various technical publications and, therefore, a brief outline of its essential features will suffice. The orebodies are of the schist replacement type, the main sulfide mass being a large lens-shaped body approximately 7 acres in cross-sectional area. In general, the mineralization is found along the iron-schist contact, with the orebodies extending-about 1000 ft. along this contact and varying from a few feet to 250 ft. in width. The mine is located on a mountain slope and has openings into it on three horizons, as follows: 1. Raises and ore passes open vertically into the shovel pit. These extend down to the 1000-ft. level, where they terminate as loading bins in the Hopewell adit. The main fan intake air shaft, which also extends vertically down to the 1000-ft. level, has its surface opening on the hillside at the extreme north end of the shovel pit, and the main mine air return exhausts through a raise at the extreme south end of the shovel pit. 2. The 500-ft. level adit. 3. The Hopewell adit on the 1000-ft. level. The mine has a vertical downward extent of 2000 ft. below the 1000-ft. level. Underground operations are carried on through two main shafts, both of which are wholly underground. Shaft 5 is the ore-hoisting shaft. It has three compartments and extends from the 800 to the 3150-ft. level. Shaft 6 is the service shaft, and is used for lowering and hoisting men and material. It has a large cage compartment and three smaller compartments for counterweights, ladderway, and pipe and power lines. This shaft extends from the 500 to the 2550-ft. level, and is now being extended to the 3000-ft. level. An air shaft for the downward movement of fresh air from the fan has been provided, and extends to the 2550-ft. level at this time. Work has been started to extend this air shaft to the 3000-ft. level. A return airway for vitiated mine air, in the form of raises and short connecting drifts, extends downward to the 2100-ft. level.

Jan 1, 1929

By Gilbert L. Eggert

The effects of reactor irradiation on age hardening in a Cu-2 wt pct Be alloy have been investigated in two neutron-energy ranges. During some of the irradiations, specimens were exposed to high-energy fission neutrons which passed through a boron-10 shield; during other bombardments, the boron-10 was omitted and specimens were irradiated in a reactor thermal column, or the fuel configuration was modified to increase the thermal-neutron flux at a location in the core. Differences in length, X-ray diffraction angle, and hardness indicated that low-energy neutron irradiation made a small contribution to changes in the measured properties. The influence of defects generated by knock-om with less than the Brinkman critical energy or by prompt (n,y) recoil is suggested as the cause of this effect. EXPERIMENTS designed to test the effects of reactor irradiation on the properties of age-hardening alloys have to the present time employed fluxes un-differentiated according to neutron energy. Billing-ton and Siegell in 1950 were the first to perform such an experiment and to compare the results with those obtained by thermal aging. These authors concluded that precipitation in a Cu-2 wt pct Be alloy was not enhanced by the radiation. However, 4 years later, Murray and Taylor,2 working with specimens of the same Cu-2 wt pct Be alloy, reported that an increase in density, hardness, and resistivity which followed reactor irradiation resembled changes associated with thermal aging at about 100°C. (It should be noted that these authors reported that higher aging temperatures caused a decrease in resistivity.) cupp3 reported hardness results similar to those of Murray and Taylor. Koppenaal4 showed that irradiation-enhanced precipitation and irradiation defect hardening were not simply additive but that they acted separately in an irradiated alloy. Kernohan et a1.,5 working with Ni-Be, offered evidence that beryllium was removed from solid solution by reactor irradiation and suggested that the mechanism was one of increased diffusion through the use of vacancies in the structure. piercy6 also found that more precipitate particles were formed by fission-neutron irradiation of a Cu-Co alloy which contained a small amount of particles before irradiation. He proposed that the additional particles were caused by an appreciable amount of diffusion during the final cooling of displacement spikes. The retrogression of extant precipitate particles found by Murray and Taylor2 and Boltax7 as well as piercy6 indicated that nuclei were dissolved within a high-energy spike region and, upon resolidification of the perturbed volume, new nuclei precipitate and grow by enhanced diffusion. Bleiberg et al.' and Konobeevski et al.' explained phase changes obtained by irradiating fissionable alloys in terms of retrogression and re-precipitation in regions of high-energy spikes. Parsons and Balluffi10 used electron microscopy to verify that crystallization did indeed occur in displacement spikes which were formed in amorphous germanium by fast-neutron irradiation. The concept that low-energy neutron irradiation might cause structure-sensitive property changes in semiconductors by atomic recoil associated with the (n, y) reaction was first proposed by Schweinler" and walker." This thesis was tested by Cleland and crawford" and found to be valid. Coltman et al.14 exposed a variety of pure metals to thermal-neutron irradiation at cryogenic temperatures and attributed the resulting resistivity changes to the action of defects created by (n, y) recoil. The present work was undertaken to extend the concepts of Schweinler," walker," and Coltman et al.I4 to the case of an age-hardening alloy and to determine whether or not the action of defects produced by thermal-neutron irradiation would en-hance age hardening. EXPERIMENTAL PROCEDURE Omeea West Reactor Irradiations.* Thermal-

Jan 1, 1965

By E. P. Pfleider, D. H. Yardley

Layers of magnetic taconite of above average magnetic iron content extend down dip on the Mesabi Range to depths beyond the reach of open pit mining. A selected layer with thickness of 75 to 100 ft underlies many square miles. Such a selected layer can provide over 50 million tons of recoverable concentratc per square mile, at lower concentration ratios than in the present open pit taconite operations. The system contemplated would consist of large scale underground quarrying by a lane and pillar method. Working heights would be 60 to 100 ft; room widths, 50 to 75 ft; and productivity targets, about 40 tons per man-shift. The most critical problems would he roof control and blasthole drilling. The successful operation of large open pits and concentrating plants for treatment of magnetic taconites indicates that the basic techniques and economic problems of pellet production have been solved. The open pit reserves are large, but they are not necessarily available in sufficient quantity or quality to provide an adequate raw materials base for all potential producers. Furthermore, as the more easily available open pit crudes are used up, the pits will become deeper, stripping costs per ton of concentrate will increase, and recoveries will decrease as leaner crudes are utilized. The time will come when supplementary and replacement reserves of magnetic taconite will be required. One way these can be obtained is by underground mining of the down-dip extension of the Mesabi magnetic taconites, especially those layers averaging well over 25% recoverable iron. A key point in such a proposal is the possibility of realizing substantial savings by beneficiating an ore of 30% magnetic iron at 2.5 to 1 ratio of concentration. This contrasts with current practice in Mesabi commercial taconite plants, where the ore averages 22 to 25% magnetic Fe, with concentration ratios of about 3.0 when producing 61% Fe pellets. Two factors which favor the eventual development of underground taconite mining are: 1) the desirable physical structure and high grade of taconite pellets in general and 2) the improved engineering techniques in underground mining. Experience in large scale room and pillar mines demonstrates that, given strong rock strata immediately above a high grade mining

Jan 1, 1963

By George Harrington

THIS paper is a brief description of the design and equipment of a new coal mine in southern Illinois, which has many features not common practice in shaft coal mining and which is laid out and equipped for such unusually large capacity that it promises soon to become one of the largest mining operations of its kind. Shaft sinking for the mine, New Orient, was commenced in May, 1921, by the Chicago, Wilmington & Franklin Coal Co. In October, 1924, the plant was practically completed and was producing over 6000 tons of coal per day. There is good prospect that within a few years, when the mine is fully developed and manned, the output will attain a daily rate of 12,000 tons. The coal seam at New Orient lies approximately horizontal, about 500 ft. below the surface, and may be said to run from 9 to 12 ft. in thickness. The tendency in Franklin County has been toward large mining units (5000 to 6000 tons per day) with great care being given to protection against fire and explosion hazards, and usually with quite elaborate surface plants permitting careful preparation of the coal into graded sizes comparable with those made in the anthracite region. The field is unionized, with uniform conditions of wages for various classes of work, hours, etc., and the Illinois mining laws are quite specific with regard to fireproofing and safety measures. These conditions make it difficult for any but well-equipped and well-operated mines to meet the competition of the numerous fine properties of which this county can justly be proud. The coal company's property was already developed on the western side by the Orient. mine-a much visited and written about operation (with which many of you are possibly familiar through the Department of Mines' film "The Story of Coal ") which until recently held the 8-hr. production record with 8218 tons and usually ran quite consistently with production of slightly over 6000 tons per day. Experience at Orient was naturally one of the greatest influences in determining the location and character of the New Orient.

Jan 2, 1925

By Laurence Delisle, Aaron Finger

THE alloys formed by the addition of nickel to iron by convelltional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.? owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect could be obtained in alloys of iron and nickel prepared by powder metallurgy technique. PROCEDURE Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, 0.001 5 ; lead, 0.035; tin, 0.025 ; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A representative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 3 2 5-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the surfaces of the particles. The reduced powders, slightly caked, were ground in a mortar and screened again through a 325- mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hydraulic presses. The pellets were compacted in a cylindrical die, ½ in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specifed for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946