Search Documents

By T. L. Joseph

Blast furnaces are most efficient thermally when the CO2 in the top gas is highest. Oxygen introduced in the air blast is converted to CO in the combustion zones. The extent to which CO, generated in front of the tuyeres, is converted later to CO2 depends upon the ratio of ore to coke in the charge and the degree to which CO2, formed by reduction of iron oxides with CO, reverts to CO by the secondary reaction C + CO2 = 2CO. About 300 to 400 lb. of carbon' per ton of pig iron is normally involved in the solution-loss reaction or direct reduction of FeO with carbon, which produces the same over-all results; that is, lower CO2 in the top gas. Rich2 has recently reported a reduction in fuel consumption at slower rates of blowing on two furnaces in spite of higher heat losses per ton of iron. Lower fuel consumption at slow operating rates was due to more complete reduction of the ore that resulted in higher CO2 in the top gas and consequently more efficient use of carbon. Kinney3 has reported substantial savings in fuel as a result of crushing and sizing the ore charge. Improvements in practice brought about by sintering magnetite concentrates, flue dust and fine ores have been due to the establishment of conditions favoring more complete reduction of the ore in the upper part of the furnace. The extent to which oxides and fluctuations in composition in pig iron affect the quality of steel and finished product needs further study. There is evidence that more thorough preheating and reduction of the ore in the upper part of the furnace tend to give a better quality of iron. Bogatzkii4 found from laboratory work that the amount of oxygen entering electrolytic iron, melted under various slags, was directly proportional to the concentration of free FeO in the slag and inversely proportional to the basicity of the slag. Herty and Gaines5 concluded that the silicate content of open-hearth steel before deoxidation is related to the concentration of silica in the pig-iron charge, indicating that most of the persistent inclusions are silica from the iron. They also found that

Jan 1, 1936

By Tedsen L. F., Dorn J. E., A. E. Flanigan

since aluminum-alloy sheet may be used occasionally at moderately elevated ternperatures, the effects of temperature on the mechanical properties are of interest. Recently the short-time tensile properties of several high-strength materials have been studied at temperatures up to 3750°F.l This paper deals with stress-rupture and creep properties at the same temperatures. The work was done at the University of California as a portion of the project NRC-548. It was financed by the War Production Board and was supervised by the Office of Production Research and Development. This paper has been released for publication by the latter agency. The following materials were studied, all in the form of 0.040-in. sheet: Alclad 24s-T Alclad 24s-T8I Alclad 24s-T86 Alclad 75s-T R3oI-T (clad) Specimens were loaded in tension in the cross-grain direction. Testing temperatures included 94°F., 2II°F., 300°F., and 375°F. Stress levels were selected to cause rupture in times ranging from several minutes to 1000 hr. In each test the following data were obtained: (I) fracture time, (2) elongation at fracture, (3) the complete strain-versus-time curve (creep curve), (4) creep rate (defined in a later section). Materials Materials for specimens were obtained from the manufacturers' commercial

Jan 1, 1947

By J. E. Smith, P. B. Crawford, B. L. Laudrum

A method is presented by which the displacement efficiency of a steam-injection process may be determined. The method consists of a determination of the position of the steam front at a particular time and the application of the Buckley-Leverett theory to the hot and cold regions of the reservoir with the appropriate hot or cold fluid properties. A uniform, linear flow system is assumed for this study. The method is applied to a number of reservoir conditions. The primary properties which affect the results of a steam-injection process are the oil viscosities at steam and reservoir temperatures, injection rate, pay thickness and oil saturation. The efficiency of steam injection is compared with that of water injection for a 10-acre, linearly flooded reservoir. In reservoirs where the oil viscosity is about 35 times the water viscosity, the steam process yields recoveries about 20 per cent higher than the water flood. Where the oil viscosity is near 500 cp, the steam process may recover from three to four times as much oil as a water flood. INTRODUCTION In a previous paper,' a method was suggested for evaluating a steam-injection process. Emphasis was placed upon the determination of the steam-front position in the reservoir at various times. In the present paper, the displacement process is studied in more detail. The approach is essentially that employed by Jordan, Rayne and Marshall3 in their study of hot-water injection. The steam-injection process is quite complex, and an exact description of the process has not been found; however, a qualitative description can be made. When a quantity of steam is injected into a relatively cold reservoir, the leading edge of the steam front continaally flows into cool sand, and some steam condenses. As more and more steam condenses, a bank of condensed water will form which is augmented by displaced connate water. The reservoir may be divided in three regions—(1) a region containing displaced fluids at reservoir temperatures, (2) a region contain- ing water at reservoir temperature and (3) a region occupied by steam. The reasons for the lack of a region of hot water or oil of any appreciable size have been discussed.' A method has been presented by which the location of the steam front can be determined even when heat losses to the regions surrounding the reservoir are sizable compared with the amount of heat injected. It remains to show the effectiveness of steam injection in increasing the ultimate oil recovery. To illustrate the technique for determining the increase in displacement efficiency and, hence, the increase in ultimate production, two sets of hypothetical reservoir conditions will be studied in detail.

By L. W. Eastwood

The structure of eutectics has been studied by a number of investigators, and the complexity of the structural relationship of the components has been agreed upon, especially that of the "eutectic colony," type III of Portevin's1 classification. This paper does not attempt to alter the present classifications of eutectics; rather, it discusses the relationship between the macrostructure and the microstructure of the copper-cuprous oxide eutectic, and describes in detail the mechanism of the formation and the structure of the eutectic. Further, throughout the entire discussion it attempts to point out certain misconceptions in regard to the interpretation of the observed structure of the copper-cuprous oxide eutectic, one of the so-called "eutectic colony" types, and to correlate as much as possible the work done by the writer with that done by other investigators. Of the three types of eutectics listed by Portevin,2 the eutectic colony type has presented the greatest difficulty in interpretation. Although the copper-cuprous oxide eutectic is typical of the eutectic colony type in appearance, it may not be truly representative because the copper forms about 96 per cent of the eutectic and the cuprous oxide about 4 per cent. The interpretation of the origin and structure of the "eutectic colony" given here is strictly limited, therefore, to the copper-cuprous oxide eutectic. Macrostructure Fig. 1 shows the macrostructure of the eutectic at 3 diameters, the melt having been chill-cast into an iron mold, the resulting specimen sawed into two parts and the section polished and etched with the usual mixture of hydrogen peroxide and ammonium hydroxide. This specimen contains 0.48 per cent oxygen and is only slightly hypereutectic. If such a melt is allowed to cool slowly, large macrograins will form without the columnar structure of Fig. 1 and the well-known phenomenon of liquation will occur, forming copper oxide dendrites at the top and copper

Jan 1, 1934

By Stephen Royce

[Stephen Royce.. I .......................... E. S. Moore.. 9 .......................... E. L. Bruce.. 10 ......................... J. E. Hawley.. 11 ........................ L. M. Scofield.. I 2] STEPHEN ROYCE, * Crystal Falls, Mich.Having examined and reported upon the Steep Rock Lake property and vicinity on several occasions for clients, and having kept in touch with the operation from 1938 on, the writer offers the following discussion of the valuable paper by Messrs. Roberts and Bartley, which was so kindly prepared in response to the writer's earnest request, made as a member of the Committee on Mining Geology. ORIGIN OF THE ORES The writer wishes to express complete agreement with the authors that the origin of these deposits was replacement action by hot ascending sulphide solutions of igneous origin, gaining access via the limestone and dolomite breccia channels, and acting mainly to replace the dolomite and limestone breccia with hematite and hydrated hematite. Some replacement in adjoining greenstones and tuffs by the same solutions may also have taken place, but the latter occurrences may represent replaced iron formations originally bedded in with the volcanics. Iron formation in the same relationship to volcanics is extensively developed on the western Menominee Range of Michigan, in the Middle Huronian belts; also appears in similar relations on the Vermilion Range; and is abundantly exposed in the same stratigraphic position no farther away than the southeast arm of Steep Rock Lake itself. Furthermore, the writer's classification of drill cores, made June 11, 1938, on the prop¬erty, contains the following, for hole 8, in the original strike of the A ore body: "332-342 ore; 342-350 much-leached sugary chert with thin ferruginous slate bands." This is a typical iron formation. The ore in this first group of holes (Numbers 6 to 13, incl.) is described in the writer's 1938 notes as follows: "The ore is hard, massive hematite with some limonite, and shot through with many small vugs." The breccia forms in the float ore and in the drill samples were also noted. As a field classification this does not check badly with Professor Schwartz's microscopic work. Notes supplied by Mr. Neeland, then geologist at the exploration, show: "Hole 23 has some iron formation, not logged yet." It appears therefore that there is some iron formation at the exploration, much iron formation in similar stratigraphic position in the vicinity, and iron formation similarly located as to volcanics on the Vermilion and western Menominee Ranges. Certain of the holes, notably Holes 25 and 27, showed some specular hematites resembling those known to be formed from cherty iron formation elsewhere. Hence the writer concludes that at least a small part of the Steep Rock ores results from replacement of iron formation. By far the greater part of it is, as the authors say, clearly a replaced limestone and dolomite breccia, with the breccia outlines still preserved in much of the ore, and all of the replacement is by hot ascending waters. The authors' citation of the neighboring Atikokan pyrite, pyrrhotite and magnetite

Jan 1, 1943

By J. Mackintosh Bell

The history of the South Lorrain mining camp is given and comparisons are made between the local topography and general geology and that of the Cobalt camp. The character of the silver-bearing veins and their analogy to those of Cobalt are given and the theory regarding the cause of the deep seated oxidation in South Lorrain, particularly at the Keeley Mine, is outlined. The oreshoots are described, also the conditions governing their occurrence and position. The mining and metallurgical practice are briefly considered. IN THE numerous districts subsidiary to Cobalt, and carrying mineral deposits similar in character to that world-famous mining camp, the most interesting recent developments have occurred in South Lorrain. The district, the center of which lies about 16 miles southeast of Cobalt, was the scene of a rush in 1907 but, in spite of the success of the Wettlauffer mine, the locality soon lost its popularity, largely on account of the unsavory early history of the Keeley mine. In recent years, following the successful development of this property by the London operators, who acquired it from the liquidator of the original company, and the later conspicuous progress made on the properties of the Mining Corporation contiguous to the Keeley on the north, the district has again come into prominence and, at present, is doing much toward maintaining the gradually declining production of Cobalt itself. Apart from the Mining Corporation of Canada and the Keeley Silver Mines Limited, the principal concerns now operating in South Lorrain are the Lorrain Consolidated, the Trout Lake Mines (operated by English interests associated with the Mining Corporation) and the Canadian Lorrain Silver Mines (operated by the Huronian Belt Co., of London). A number of minor prospects are also active. The Wettlaufer and Currie, on both of which considerable work was done some years ago, are now closed.

Jan 1, 1924

By B. Egeberg

IN A previous paper1 the authors dealt with the physical properties of cold-rolled and heat-treated Britannia metal of the approximate composition Sn, 91 per cent., Sb, 7 per cent. and Cu, 2 per cent. It was found that cold rolling to more than 50 per cent. reduction produced a continuous softening of the metal when measured by the Brinell machine, whereas the Shore instrument indicated increased hardness; that the strength of the material followed the Brinell hardness and that the metal therefore became weaker the more it was cold-rolled; and further, it was found that hardness and strength could be largely restored to the cold-rolled metal by "baking" for about one hour at any temperature, between 200° and 450° F., the melting point. The higher the baking temperature, the more effective was the heat treatment as far as increased hardness was concerned. It seemed to be of little importance whether the metal was soaked or not at the baking temperature for a great length of time and the rate of cooling seemed to be immaterial. The present paper deals with the same alloy and more particularly with the resistance towards various forms of stress - tensile, bend and deep drawing. The metallography of Britannia metal has in part also been covered and an explanation attempted for the abnormal behavior of this alloy.

Jan 1, 1929

By Herbert Clark Hoover, Lou Henry Hoover

THE third book has explained the various and manifold varieties of veins and stringers. This fourth book will deal with mining areas and the method of delimiting them, and will then pass on to the officials who are connected with mining affairs'. Now the miner, if the vein he has uncovered is to his liking, first of all goes to the Bergmeister to request to be granted a right to mine, this official's special function and office being to adjudicate in respect of the mines. And so to the first man who has discovered the vein the Bergmeister awards the head meer, and to others the remaining meers, in the order in which each makes his application. The size of a meer is measured by fathoms, which for miners are reckoned at six feet each. The length, in fact, is that of a man's extended arms and hands measured across his chest ; but different peoples assign to it different lengths,

Jan 1, 1950

By J. L. Swedlow, M. L. Williams

Two standard techniques for assessing fracture initiatlon in sheet specimens involve measurements of 1) the applied load of fracture which, via linear fuacture mechanics, is used to find the fracture tough/less SC (or SIC), and 2) the velative displacement of fracture of the opposite free faces of the crack (COD). In the past, the quantitative association between these two parameters has not been determined in detail, owing to the mathematical difficulties of computing. the stress and strain fields in the combined elasto-plastic flow near the crack. Using a numerical technique Irecently developed and applied to a 7075- TO' aluminum plane stress specimern, the two parameters noted have been determined and associated quantitatirely. CONSIDERABLE effort has been expended in selecting a rigorous yet practical manner for predicting fracture. The usual point of departure is the modified Griffith criterion in which the mechanism of energy dissipation is reflected in Sc (or SIC), the parameter of "fracture toughness". Sc. differs from the surface energy used by Griffith in perfectly brittle fracture in that it includes the effect of plastic flow in the vicinity of the crack tip. Because plastic flow alters the stresses and displacements predicted from the usual linear theory of fracture mechanics, and because analysis of the nonlinear stress-strain field has presented great obstacles: only estimates of several pertinent quantities have heretofore been available. Nevertheless, two parameters have often been measured experimentally althougll usually just at the point of fracture. These are the energy release rate, or fracture toughness 9, (or I,), and the crack-opening displacement (COD). Such observations have been used in connection with frarture criteria and have been most helpful in design, although their application requires care with respect to changes in geometrical configuration from that upon which the criteria were based 1,2 Recently, however, a reasonably accurate and comprehensive method for analyzing the elasto-plastic flow has been devised and applied to plane stress specimens having arbitrary octahedral stress-strain curves.3 It thus becomes feasible to compute, albeit numerically, both the fracture toughness and crack opening as functions of the applied tensile loading on a typical specimen geometry. As a result, it is now possible to associate these two parameters quantitatively, and thereby to associate data obtained by one method with data pertaining to the other. ELASTIC ANALYSIS For the case of linear elasticity, it is relatively easy to deduce the connection between various measures of crack deformation. Using, for example, the singularity analysis, it is found that the leading term of the Airy stress function x f°r symmetrically applied loadings on an isotropic medium is

Jan 1, 1968

By James H. Courtright, Kenyon Richard

L. H. Hart (Chief Geologist, American Smelting & Refining Co.)— Because of a widely recognized association between breccia pipes of one form or another and many important copper deposits, conditions under which breccia pipes develop have been of great scientific interest for many years. Since these phenomena first attracted attention, many theories have been advanced to explain their origin. This is not unexpected, since it is likely that they have been formed by and under a wide range of conditions. Moreover, the entire subject is confused by the fact that the term brec-cia pipe is applied to a wide variety of occurrences. To discuss any part of the subject intelligently, therefore, it is necessary to start with definitions of the terms used. In their discussion of the Toquepala deposit, Richard and Courtright have carefully defined the terms they have used in their presentation of a very logical geological history of Toquepala breccias. This is a real contribution, as there is no reference in the literature known to the writer where the history of a series of breccia pipe epochs, confined essentially within one channelway, may be read with the degree of certainty that appears to be possible at Toquepala. Although the following comments are intended primarily to emphasize points brought out in the article by Richard and Courtright, certan subsequent detailed mapping by Hollister and Houston7 within the main central mineralized area of the Toquepala deposits not only supports most of Richard's and Courtright's con- clusions but also contributes additional facts that strengthen and broaden the whole concept of the origin of the Toquepala breccia pipes. In detailed mapping by Hollister and Houston,' the most significant feature disclosed is a well developed system of concentric fracturing in rocks peripheral to the main breccia pipe throughout an arc of 300°, interrupted only by the late dacite agglomerate in the north quadrant. Although Richard and Courtright noted that such fractures were developed in the southern and southeastern areas, continuity in the east and west quadrants is established by consistent orientation of the stronger set of fractures and joints. The existence of these structural weakness trends is emphasized by the emplacement of dike-like phenomena in and along members of this fracture system. Richard and Courtright described one of these dikes in the southeast quadrant. They referred to it as a ring-dike, composed of dacite porphyry. This suggests an apparent structural control of at least a part of the dacite porphyry intrusion by features related to the Toquepala breccia pipe center. This raises a perplexing question, since the dacite porphyry intrusion had been presumed to antedate breccia pipe activity. However, if this ring-dike is related to the breccia pipe center, it may indicate that some part of the dacite porphyry intrusion advanced in a manner resulting in an intensely localized stress center, which produced the concentrically arranged fracture system. The ring-dike would then appear to be evidence strongly sug-

Jan 1, 1959

By Frederick Laist

THE ore from the Butte mines of the Anaconda company is quite siliceous; that is, it contains considerably less iron than is needed for the fluxing of the silica. The direct smelting of this ore, therefore, requires the addition of considerable fluxing material. The only flux available in sufficient quantity at Anaconda is limestone containing no metallic minerals. This necessarily makes the direct smelting of the ore so expensive that it is more profitable to subject the ore to a preliminary treatment by concentration. However, as the losses in the concentrator were very high, compared with the losses in the blast furnaces, it was found, by calculation, more profitable to send ores containing more than a given percentage of copper to the blast furnaces, in spite of the higher costs of treatment. The dividing point was dependent on various factors, the chief of which was the prevailing market price of -copper. It was customary, therefore, to segregate the ore as mined into two classes. Ore in the first class generally contained 5 per cent. or over of copper;: this was sent directly to the blast-furnace department. Second-class ore contained less than 5 per cent. of copper, and averaged around 3 per cent.; it went to the concentrating department. With the introduction of the flotation process, it was found possible to maintain an average recovery, as concentrates, of 96 per cent. At the same time, the cost of reverberatory smelting was very materially decreased by the use of pulverized coal. These two changes in practice made the blast furnaces unable to compete with the reverberatory furnaces on a cost basis. The distinction between first-.and second-class ore was therefore abandoned, and the ore was treated by concentration. Obviously, on ores as high in iron as the Butte ores, the concentrator, produces a product that is self-fluxing; in fact, it is possible to produce a

Jan 1, 1920

By C. D. Woodward

The Anaconda Copper Mining Co. purchases 25,000 kw. of electric power for its mining operations at Butte, Mont. This power is delivered, over duplicate feeders, in the form of 60-cycle, 2400-volt, three-phase current, to five compressor plants, where most of the energy is used for driving air compressors. At the compressor plants are located the switching apparatus for controlling the 2400-volt power and distributing it to the various mines. At these points, also, there are a number of motor-generator sets for converting the alternating current to 275-volt direct current for the haulage systems. Pole lines convey the powcr from the compressor plants to outdoor transformer substations at most of the mines. When it is not economical to distribute the power at the lower voltages in the mines, transformers and motor-generator sets are placed at strategic points underground. All power is purchased on a maximum-demand basis; therefore there is installed at one of the compressor plants an eight-element totalizing graphic wattmeter. This instrument records simultaneously the value of all power taken at the numerous points of delivery, which not only climinates the diversity factor but permits load dispatching between compressor and pumping plants, and thus materially reduces the maximum demand from the power system. As most of the mine hoisting is done by 90-lb. compressed-air winding engines, the air-compressor equipment for the winding engines and mining operations is quite extensive. The standard air compressor has a rating of 7500 cu. ft. per min. of free air, and most of the compressors are directly connected to synchronous motors. The synchronous motors are designed for 80 per cent. loading power factor, thus facilitating power-factor correction of total mine load. Consequently by cooperation with the power company, the voltage of the power received at the compressor plants is constant. In the mines there are installed an induction motor load of approxi-mately 10,000 hp., and 4500 kv.-a,, in transformer capacity. It is the practice to install 2200-volt motors in the mincs, except those rated below 50 hp, hence there are in operation underground about 5000 hp., in the

Jan 1, 1923

By W. N. Lacey, B. H. Sage

An apparatus is described for the measurement of the pressure-volume-temperature relations of pure substances, simple mixtures and complex mixtures with an over-all absolute uncertainty, which is usually not more than 0.2 per cent. The equipment is suitable for studies in the gaseous, two-phase, and liquid regions. The behavior of such systems may be investigated at pressures as high as 10,000 lb. per sq. in. for temperatures between 70 and 600 F. The methods of measurement and the construction of the apparatus are described in some detail. The measurement of the volumetric behavior of multicomponent systems requires the simultaneous measurement of the pressure, volume, temperature and weight of each component of the system. In the present apparatus a sample having constant weight is investigated at a number of independently controlled pressures and temperatures, therefore it is necessary only to establish the weight of each component added before a given set of measurements. This method is in distinction to that in which the total volume remains constant and the pressure is varied by addition or removal of material, the system having variable weight. An objective in the design of the apparatus to be described was to develop equipment that would yield results involving no uncertainties larger than 0.25 per cent throughout the range of pressures from 150 to 10,000 Ib. per sq. in. at temperatures between 70" and 600" F. Although this over-all absolute uncertainty of measurement may not appear to be small, it necessitated care in the plans for control and measurement of each of the fundamental variables. In general, any uncertainty greater than 0.05 per cent in the pressure, volume, absolute temperature or weight of each component was considered undesirable; therefore the attempt was made to obtain a precision of measurement in each case such that the absolute uncertainty would be only half this amount except in certain regions near the ends of the experimental range of the variable under consideration.

Jan 1, 1940

By A. F. Lucas

The discovery of oil in 1901 on the Spindletop dome, Texas, inaugurated a new industry on the Gulf Coast, an industry which has gran with the discovery of successive fields, until today it engages the services of thousands of workers and employs enormous capital. New fields are being discovered from time to time and doubtless some still remain to be found, though of late years discoveries have become more infrequent. Nowadays several hundred dry holes are drilled each year in a fruitless and blind effort to discover new fields, for as yet geologic science has developed no effectual method of locating the coastal oil deposits in advance of drilling. Moreover despite the occasional discovery of new fields, the total production of the Gulf Coast is today no greater than it was in 1906, for the added production of the new fields has been offset by the rapid decline and more or less complete exhaustion of some of the older ones. Careful geologic work within the fields has in some cases increased the production temporarily, but has developed no really new supplies. The Gulf Coast oil industry seems to have passed its period of greatest expansion and to be declining at a fairly steady rate, and this condition is naturally viewed with alarm by the more farsighted operators. In my opinion, the time has come for the adoption of radical and aggressive methods of prospecting; and a fraction of the money wasted yearly in drilling shallow wells in hopeless locations might well be devoted to this purpose. Many facts lead me to believe that all the salt-dome oil has had a common origin; that it has migrated up from considerable depth along lines of structural weakness; and that a deep well, properly located, stands an excellent chance of discovering the parent reservoir and thus of developing new and probably great supplies. This paper is presented as a discussion—necessarily hypothetical and based largely on personal opinion—of the possibility of encountering deep-seated oil deposits beneath the salt domes. Salt-dome Structure All of the oil produced in the coastal region of Texas and Louisiana is probably associated with salt domes, though in Goose Creek, Edgerly, and one or two other fields no salt has yet been actually penetrated. As

Jan 1, 1920

By M. Sagheer

This paper gives a report of the laboratory work investigating the fundamental flotation characteristics of chromite and its commonly associated mineral, serpentine. Floatability curves, showing floatability of chromite at different concentrations of sodium oleate and pH, were obtained by pick-up method. One of the difficulties encountered in flotation of chromite in presence of serpentine has been attributed to dissolved metal ions. The influence of metal ions, dissolved in pulp filtrate, on floatability of pure chromite and serpentine has been studied and it has been shown that Mg, Ca and Fe ions depress chromite. A considerable amount of work applying bubble pick-up method was carried out to counteract the depressing action of metal ions. Various methods and reagents were applied in this connection. Validity of each method and reagent has been discussed. Probably due to the abundance of high-grade chrome ores, very little has been published concerning the flotation of chromite. As improvements in mineral beneficiation are realized, more attention is being directed to low-grade ores previously considered unusable. Currently, gravity concentration is the principal process applied to upgrade chrome ores, but this cannot be used for finely disseminated ore because of the substantial losses in the fines,1,2,3 To avoid these losses, flotation can be applied to material which is too fine for satisfactory gravity concent ration, and it is probable that a combination

Jan 1, 1967

By Richard W. Smith

There are three distinct varieties of phosphate rock, in Tennessee, known commercially as: (a) the "brown" rock, which is the residual product of the weathering and natural concentration of certain phosphatic Ordovician limestones; (b) the "blue" rock, which is an unaltered phosphatic stratum of Mississippian or Devonian age; and (c) the "white" rock, which is the result of chemical replacement and deposition. Before 1894, South Carolina and Florida had supplied most of the phosphate of the United States, South Carolina leading until that date and Florida from then until the present time. In December, 1893, the blue phosphate of Tennessee was discovered almost simultaneously on Swan Creek, in Lewis County, by two independent parties—by one as the result of a careful and systematic search for a workable deposit of the long known kidney phosphate, and by the other through mistaking it for a "bloom" of coal. Leases were taken and, with further prospecting disclosing other deposits in the region, the development progressed as rapidly as could be expected without railroad transportation. In January, 1896, Judge S. Q. Weatherly, who was interested in the development of the blue phosphate, while riding along the road south of Mt. Pleasant, noticed some slabs of a brown rock in place above the limestone. He took samples, and had them analyzed, thus discovering the high-grade brown phosphate of this district. This discovery was kept a secret until July, 1896, when mining was started at the village of Mt. Pleasant. Development proceeded rapidly, many owners obtaining their capital by the sale of their rock fences, which were largely composed of slabs of high-grade brown phosphate. The development of the brown rock, which is richer and more easily mined than the blue, caused Tennessee to advance from a poor third in production to second, surpassing the output of South Carolina, and being excelled only by Florida.

Jan 1, 1927

By O. George Specht, Carl A. Zapffe

IN recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experimentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. GROUP I: REDUCTION WITH HYDROGEN Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1946

By P. H. Brace, N. A. Ziegler

The study of the relations between gases and metals is one of pcren-nial interest to all who are connected with the production of high-grade metallurgical products. The data reported here are the outcome of work of which the object is to determine the effects of dissolved gases upon the properties of metals and to gain a more detailed knowledge of the reactions between gases and molten metals, particularly iron, under definitely controlled conditions. We have attempted to reduce our margin of error by dealing with relatively large quantities of metal, from 4 to 13 Ih. (2 to 6 kg.), and keeping the ratio of refractories to metal as small as practicable. The ingots produced are large enough to provide adequate material for making determinations of magnetic and other physical properties. In choosing the bell-jar type of furnace we were influenced by the results of considerable experimentation along the same general line which indicated that, for the scale on which we were to work, it was important to have the furnace structure independent of the vacuum enclosure. The use of a bell-jar surrounding the entire furnace accomplishes this and also gives great freedom of observation during operation and ready accessibility for the replacements which are necessary after each run. Our choice of analytical method was made in the light of the results secured by H. M. Ryder, who used a method similar in principle for the analysis of very small quantities of gas extracted from strips of metal heated electrically in high vacuum. We have presented some selected preliminary experirnental data as being illustrative of the quantity and nature of the gases which occur in iron of different origins, but do not urgc any hypothesis at this time. The Furnace Our furnace may be described as "a high-frequency induction furnacc of the bell-jar type." It is similar in a general way to that described by Cain and Peterson1 though we have introduced certain refinements of

By C. H. Mathewson

ABOUT fifty pages of Henry M. Howe's profound treatise, "The Metallography of Steel and Cast Iron," are devoted to twinning with special reference to the origin, nature and general significance of the Neumann bands in ferrite. Howe believed with Osmond and Cartaud1 that the Neumanns are mechanical twins and his careful observations leave no doubt that these straight-sided narrow bands habitually occur parallel to trapezohedral planes of form {211}. Attempt's to develop the structure of the bands by various methods so that their identity could be established beyond question have not been conspicuously successful. Howe thought that they deflected slip bands. Some of the etching figures which have been developed within and adjacent to Neumann bands support the contention that they are twins. A good example of this effect in ferrite containing 0.6 per cent. of nickel and 1.3 per cent. of phosphorus, originally due to Harnecker and Rassow,2 was reproduced in. the 1928 lecture before the Institute of Metals Division on twinning in metals.3 In this case, the sides of the figures might represent the traces of cubic planes laid bare by etching a properly oriented grain of ferrite, twinned along a plane of form {211}. Our own observations in this direction may be represented by Fig. 1 which shows in a deeply etched cavity in the boundary region between a Neumann band and the original crystal two small crystal surfaces which resemble the faces meeting at a reentrant angle in the simple cube twinned along a bisecting plane of form {211} as sketched in Fig. 2.

Jan 1, 1928

By B. K. Miller, George E. Moore

THE Missouri fire clays are here divided into plastic and semiplastic clays occurring as widespread bedded deposits in east central Missouri and flint and diaspore clays occurring as isolated "sink-hole" deposits in the north central Ozark region. Visual inspection was the first method used in clay prospecting. Thin overburden, hard sandstone "rimrocks," and the occurrence of diaspore float made this method particularly applicable in the flint and diaspore fields. The first drilling tool used was a hand auger. One man can drill 25 to 50 ft. per day at a cost of about 35 cents per foot. Holes can be drilled to a depth of 150 feet. Spud drills are often used where the over burden is hard. This drill uses a slotted earth socket bit. A two-man crew can drill about 100 ft. per day at a cost of about 35 cents per foot. Mechanically powered auger drills have been used extensively in wildcat drilling in the past few years. This type of drill furnishes a continuous set of cuttings. The practical depth limit with this drill is 50 to 60 ft. Two men can drill 300 ft. per day at a cost of about 20 cents per foot. Core drilling is used mainly to prove a known clay deposit. A two-man crew with a No. 22 Sullivan drill can drill about 30 to 40 ft. per day in soft clay, at a cost of about $1.25 per foot.

Jan 1, 1947