Search Documents

By H. C. Rolseth, J. J. Calaman

6.4-1. Principles of Operation. The jet-piercing process is a patented thermal process which depends upon a characteristic of the rock which is termed spallability. In its simplest terms, spalling is considered as decrepitation resulting from differential expansion of rock crystals due to thermally induced stresses. The number of individual properties influencing the spalling characteristics of rock are so numerous and their interaction so complex that the only truly reliable way to ascertain the spallability of rocks under thermal shock conditions is to expose them to these conditions. However, laboratory and field work have determined the principal thermal, physical, and mechanical properties of rock which affect spallability (10, 18). The approximate relationship between spallability and these characteristics is as follows: [ ] where To is the critical temperature at which, it is believed, a rock becomes elastic or sufficiently plastic to prevent further spalling action. Thermal diffusivity takes into account the amount of heat used in saturating the medium itself during the migration of a heat front. The rate and degree of dimensional changes which influence the spalling tendency of the rock will depend upon the characteristic of the heat gradient in the rock. The greater the spalling tendency, the higher the piercing rate. Those properties most favorable to a high degree of spallability are: 1. Large linear thermal expansion at temperatures below 700°C. 2. High thermal diffusivity at temperatures below 400°C. 3. Equigranular interlocking structure with little or no fine-grained clay or mica alteration products. 4. No significant amounts of soft, low-melting, or elastic mineral or materials which yield after thermal decomposition.

Jan 1, 1968

By J. D. Prater, H. R. Spedden, E. E. Malouf

Application of research findings to the old art of leaching copper from copper-bearing mine waste has resulted in a significant contribution of copper to over-all copper production. For example, at the completion of the current expansion program at the Kennecott properties in the United States, copper produced from waste dump leaching will amount to about 25% of the total production, whereas formerly only 2% was derived from this source. This planned expansion of copper leaching focused attention on the problem of developing more efficient methods for the recovery of copper from greatly increased volumes of copper-bearing so1utions.l Detailed investigations made in laboratory pilot plant and plant tests for the recovery of copper from copper-bearing solutions have included electrowinning, solvent extraction, ion exchange and cementation with iron in launders, precipitation drums, activated launders, and precipitation cones. The results of these investigations have led to the development of a precipitation cone-type recovery system having advantages over older methods.

Jan 4, 1966

By Carl H. Samans

The attention of physicists and metallurgists has been directed toward the study and explanation of the deformation textures in metals for the past 15 years. In 1920 N. Uspenski and S. Konobejewskil were first able to show that the symmetrical X-ray diffraction effects that had been previously reported by E. Hupka2 and others in metal foils were caused by a directed arrangement of the crystallites. Since then, the systematic study of textures resulting from the application of the pure forces of tension or compression to polycrystalline materials has been supplemented by many investigations on deformed single crystals, which have greatly added to our knowledge of deformation. However, despite the valuable information secured from these comparative studies only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature. This lack of quantitative data is especially unfortunate because of the much greater practical significance of rolling textures and their effects in both cold-rolled and annealed materials. This investigation was undertaken for the purpose of specifying the deformation of rolled single crystals in the hope that such information might later facilitate the explanation of polycrystal-line textures. Of the four studies that have been made upon cold-rolled single crystals, only two are of any quantitative value. S. Tanaka,3 working

Jan 1, 1934

By Akira Ishizu, Nobuo Matsui, Hideo Yamamoto, Tatsuya Nagahama

At Kamioka Mine of Mitsui Mining & Smelting Co., Ltd., Japan there are three mills, treating a total of 6400 t/d of lead-zinc Ore. In the lead-zinc bulk differential flotation at Shikama Mill the addition of reagents is automatically controlled by the feed rate, the lead and zinc content in feed, froth and tailing, the pH and the concentration of cyanide ion in the pulp. As the zinc thickener overflow at Shikama Mill contains CU(CN)3--, ZnS, CdS, CN-, xanthate and frother, all the ingredients in the over- flow other than CN are floated by using the Nagahm flotation machine, and the water containing only CN- is effectively recycled to the lead- zinc differential flotation circuit. In the lead-zinc straight differential flotation at Mozumi Mill, the overflow of tailing pond is recycled especially to the cleaning flotation circuit by decreasing the pulp density. Thus the integrated recycling of wastewater greatly reduces environmental problem and in addition, it generates sizeable profit.

Jan 1, 1977

By S. J. Hubbard, S. D. Michaelson, A. W. Last, B. H. Ensign

Of the seventeen western states, five-Arizona, Utah, New Mexico, Montana, and Nevada-produce about 90 pct of this country's primary copper. All seventeen of these states occupy 60 pct of the nation's land area but receive only 25 pct of the country's total precipitation. Seventy percent of this precipitation returns directly to the atmosphere through evaporation and transpiration, leaving very little for ground reservoir recharge or immediate domestic, agricultural, or industrial use. With so limited a supply available for all, competition for water rights among users is severe. The result does not always permit using the limited supply to produce the most valuable end product. Most of industry and much of agriculture can shop around for suitable operating locations. Where water is critical to their purposes, they can and do locate in areas where the needed amounts are available. Such is not the ordinary lot of the mining industry, which must locate in the area of the deposit it is planning to mine and concentrate. In the case of copper this happens to be, for the most part, right in the heart of the semi-arid regions of the West.

Jan 7, 1960

By J. B. Mackintosh

The general method which has been followed since the time of Heinrich Rose, and perhaps before, for the determination of phosphorus in iron and steel, is to dissolve the sample either in nitric acid, aqua regia, or some other oxidizing agent, in order to convert the phosphorus into phosphoric acid. In 1832 Rose* recommends HNO3, or aqua regia, preferably the former. Wohler, in 1854,† directs that the iron should be oxidized by burning in a stream of oxygen for the determination of carbon, and the resulting oxide of iron containing all the phosphorus as phosphoric acid be treated as an ore. In the fourth English edition of Fresenius' Quantitative Analysis,† pp. 666-667, we find directions to dissolve the iron in aqua regia or bromine; and, coming down to more recent times, we find F. A. Cairns § directing the employment of a boiling solution of potassium chlorate and hydrochloric acid for the oxidation and solution of the sample to be analyzed. It is unnecessary to multiply quotations from the literature of the subject, though they might be extended almost inclefinitely, since it would only be a repetition of the above mentioned series of methods in one form or another; and the references given have been selected to show how little essential variation there is in the type-methods of solution used. In fact it seems to be universally accepted as a necessary first step in the determination that some such method of solution should be followed. One chemist, however, struck out on a different line of thought, and to the Lest of my knowledge only one, M. V. Tantin, who, in

Jan 1, 1886

By Leonard B. Griffiths

In a recent communication, Smith and Wood described some results of 800°C compression/creep tests on WC-12 wt pct Co alloys in which plastic flow in the WC particles was believed to have occurred. The deformation observed in the WC particles was found to be a function of the rate of loading. The authors suggested that their data constituted support for the Ansell6-Lenel theory of yielding in dispersion-strengthened alloys. I do not agree with this interpretation since the Ansell-Lenel theory does not apply to the type of alloy in question. In this alloy, the dispersoid is present to the extent of about 80 vol pct. Even where there is no continuous skeleton, which apparently is the case in this instance, the simple fact is that nearly all of the load is carried elastically by the stronger material (wc).7 The constraint imposed upon the matrix, by virtue of the differences in Young's modulii and Poissons ratios, severely limits the stress level to which it may be subjected (assuming that the interfaces remain intact). If one allows for the constraint and then performs the same computation as in Smith and Wood, one finds that the stress on a WC particle is about 4 x 105 psi. This is about 21/2 times lower than the predicted fracture stress for WC. I would completely agree with the final paragraph of Smith and Wood, namely, that loading rate is of considerable significance. However. a more likely interpretation of their data is, I submit, that in the absence of stress relaxation (by secondary slip or climb) those WC-Co interfaces subjected to a normal tensile stress begin to fail. Once this occurs, the stress distribution will change rapidly and "premature" fracture of the WC then becomes quite probable. Tne serrated edges shown in Fig. 1 may very well be fine, interface fissures.

Jan 1, 1970

By Edmund C. Pechin

THE iron trade of America seems on the point of a new departure. After years of struggling against heavy odds, patient endurance in periods of depression and loss, fears and hopes alternating as failure or success seemed to be the penalty or reward ; wanting in sufficient capital, embarrassed by reason of imperfect knowledge and lack of skilled labor, confronted by a powerful foe-every doubt has at last vanished, physical and mechanical difficulties have been largely overcome, capital has become more abundant and remunerative, the excellence of our product has been everywhere established, - and the peculiarities of American character-pluck, energy, and perseverance -have at last placed the trade upon a foundation so broad and stable that upon it we begin to erect the structure of a world-wide business. Concerning the future of the iron trade in the United States there can be but little doubt. The growing scarcity and constantly increasing cost of raw material in Great Britain, their loss of labor by emigration, the social disturbances among the working-classes, assuming a more threatening attitude on each new outbreak ; the rapidly decreasing value of money, in consequence of the enormous production of gold and silver, combine to forbid any return to former prices, and indicate that a point has been reached beyond which any marked increase of production is improbable. The same causes are operating to a greater or lesser extent upon the Continent. . In the meanwhile the growing wants of humanity are rapidly outstripping these sources of supply. In addition to the steadily increasing foreign and home demand, we find, the world over, the most intense activity everywhere displayed in enterprises requiring

By Strathmore R. B. Cooke, Iwao Iwasaki, C. S. Chang

PYRRHOTITE has long been considered a gangue mineral to be eliminated as tailing in the treatment of various sulphide ores. However, in recent years the world-wide lack of sulphur resources has called attention to this mineral as a potential source of both sulphur and iron. Its importance as an economic mineral, however, has not been particularly emphasized. For this reason very little is known about its response to flotation, except that it can be depressed easily in alkaline circuit, by long aeration,1,2 addition of oxidizing agents3 or by starch.4 The object of this work was to study the floatability of pyrrhotite. This includes the effect of oxidation by aeration, of copper activation, and of change in pH.

Jan 2, 1954

SUMPEARY OF CURRENT PRACTICES History The outcrop and surrounding area of Comincots Sullivan Mine was originally mined by small open cuts on surface and small open stopes underground to which shafts and adits were driven for access. When it was established that a commercial grade of ore was available, an adit was driven on the 4600 level (feet above sea level), and OM was extracted by larger scale open stoping leaving supporting pillars where necessary. After the depth of the ore body was proven to the 3900 level and an adit driven at this level, many miles of drifts, crosscuts, raises and sublevels were driven for the extraction of the ore above this level. Larger open stopea were extended from this development. The mining method was, and to a very limited degree still is, a benching method. Due to the strong hanging wall in this area of the mine, stopes with a width of 100 feet or more were opened. In 1931, because the orebody was proven to extend below the 3900 level, a winze was sunk from the 3900 level to the 3350 level. From this winze three intermediate levels were opened. Following a plan of development well in advance of production requirements, further sinking was done by winzes and eventually a large shaft was raised to surface. Prior to 1958 the 2850 level was bottom which since that time has been extended to the 2500 level. Open stopes were developed and mined as this area was opened up.

Jan 1, 1970

By Donald R. Williamson

Ore estimation at Cyprus Pima mine begins with estimating average copper grades for mine model blocks. Accuracy of the estimates has been checked four times in the last several years by comparing the estimates with arithmetic averages of corresponding blasthole (BH) assays. The data file now contains 3.567 estimated blockgrades and more than 10,000 blasthole assays. These data were compared by straight-line regression analysis at appropriate intervals as the body of data grew. Arithmetic averages of the estimates differed each time from arithmetic averages of the BH averages by nearly the same amount. More significantly, regression curves of the new total sets of data did not change position appreciably showing that copper grade estimates of blocks in all grade ranges from the lowest to the highest grade ores remained in error by nearly the same amount. Other studies revealed that core hole assays of the dominant ore type are biased and that that bias almost equals the error in estimation. Discovery of constancy in error indicated that regression analysis could be a means for correcting estimates of average block copper grades. A correction for estimated block grades was developed. It required determining which regression is appropriate for the particular problem, and a mechanism that is demonstrably sound. This paper describes the problem and the solution: No comparable study has been, found in the literature. Two other applications of regression analysis to metal grade comparisons are presented. Each adds a bit of support to a generalization which was suggested by correction of average block copper grades, namely, when performance of an estimate is to be evaluated, the variable taken to be the yardstick for the performance should be regressed on the estimate.

Jan 1, 1980

NEW MEMBERS The following list comprises the names of those persons who became members during the period of June 10, 1917, to July 10, 1917. BANKS, LEON MAXWELL Agent 3. Supt., Grant Leasing Co. Metcalf Ariz. BEAUCHAMP, HENRY CLAY : Mine Operator, Sisson, Siskiyou Co., Cal. BOCKING, CHARLES, Asst. Mgr., Butte & Superior ,Mining Co., Rialto Bldg., Butte, Mont. BEYER, HERMAN E., Chief Engr., Condenser Dept., Ingersoll-Rand Co., 11 Broadway, New York, N. Y. BLACK, HERBERT F 1512 Oliver Bldg., Pittsburgh, Pa. BRENNAN, PATRICK J., Gen'l. Supt., Elkhorn Division, Consolidation Coal Co., Jenkins, Ky. BUTNER, DANIEL W., Chem. & Supt., Underground Min., Spanish American Iron Co., Daiquiri, Santiago de Cuba, Cuba. CARLTON, DAVE P Nevada-Douglas Cons. Copper Co., Ludwig, Nev. DE AROZENA, JOE Min. Engr., 321 Preusser St., San Angelo, Texas. DICKIE, CHARLES HERBERT, Pres., Georgia River Min. Co., Duncan, Vancouver Island, B. C., Canada. DOBBINS, WALTER Mill Foreman, Chino Copper Co., Hurley, New Mexico. DRURY, CHARLES W., Asst. Professor of Met., Queen's University, Kingston Out. Canada.

Jan 8, 1917

By A. B. Young

In the original design of the flue system, the flues from the roasters delivered their gases to a large brick dust chamber which discharged into another flue with stack connection, as shown in Fig. 1. The treater is so situated that the gases are taken by it directly from the chamber and discharged again into the flue. The complete installation comprises two treater units, only one of which has been installed at present. The treater is essentially a flue 1.0 ft. high, 12 ft. wide, and 61 ft. long. (3 by 3.6 by 18.5 m.). Suspended inside, vertically and running lengthwise, are four banks of No. 20 corrugated iron plates; each bank is 10 ft. long, making an effective treater length of 40 ft. The spacing from center to center of the rows of plat,es is 9 1/8 in. (23 cm.) giving six-

Jan 1, 1921

By E. A. Wieselmann

This chapter presents a successful approach for achieving mine entry stability at the Cane Creek potash mine by the utilization of closure measurements. The mine is located in southeastern Utah (Fig. l). Mining is being conducted at depths in excess of 3000 ft under structurally complex geologic conditions typical of the Paradox salt basin. The closure measurement systems described have definite application for determining relative entry stability in other nonelastic rocks which are similar in behavior to potash. Similar types of closure measurements have been taken in various underground openings throughout the United States, Canada, arid Europe. Application of this closure data has previously met with varying degrees of success as a tool for design of under- ground openings in both elastic and nonelastic media.1-32 Closure measurements can be made easily and economically and they provide a practical solutiori to a practical problem. They are in-situ measurements which do not necessarily require laboratory correlation. Simple closure measurements have special significance in potash because "steady-state" ' closure rate, or creep, of the entries is measured. These closure rates can be utilized because nonelastic media such as potash will never achieve absolute stability around a mine entry. The potash will tend to creep or deform until all entries are closed and the overburden stress is redistributed over what was previously the mine area. The time for this ultimate effect to occur is dependent on a number of mining and geologic variables. Percentage of mine extraction, mining

Jan 1, 1972

R. H. THURSTON, Cornell University, Ithaca, N. Y. (communication to the Secretary): The " tri-axial diagram" was, I think, first employed by me in the work of the " U. 8. Board Appointed to Test Iron, Steel and Other Metals." A model was exhibited to the American Association for the Advancement of Science, and the diagram was first published, and the model described, in a paper presented to the same society at its Nashville meeting in 1877." The problem then presented to its inventor was to find a method of planning a research involving proportions of ternary compositions in such manner that, a limited number of such compositions being tested, the results should give the law of variation in the physical properties of all possible combinations of the three elements, and the actual numerical values of such as were important to the investigator. The investigation of the binary alloys, copper and tin, copper and zinc, and tin and zinc, had been completed and satisfactorily discussed, employing the usual bi-axial diagram, of which the ordinates represented the one, and the abscissæ the other, of the characteristic properties to be studied, the composition being commonly indicated by the abscissæ. In these cases it was easy to ascertain, by the study of a limited number of compounds, the law of variation in strength, ductility, etc., with composition; but, for a long time, the ternary alloys were not attacked, because no simple and satisfactory method presented itself of securing results significant for the whole field by the investigation of a comparatively small number of alloys. The tri-axial diagram was finally hit upon as a means of representing and interpreting results, and researches were at once begun, and in due time satisfactorily completed.

Jan 1, 1899

By C. M. Marquardt

The minerals industry in general should bow in homage to the uranium milling industry. Those in the uranium milling industry have "spark- plugged" more progress in the application of instrumentation and control in the last 5 years than has been made in 50 years by the industry in general. Part of this real progress in the application of instrumentation and control has been born of necessity because milling processes are more complex. A lot of the impetus for instrumentation and control has come from the fact that the industry is new, the processes are new, and there are no hide-bound conventions to overcome. Part of it comes from the fact that much of processing is more chemical than metallurgical and the thinking of the process chemist has carried over into the plants. One need not elaborate on what instrumentation has done for the process chemical industries. Each new mill that is constructed, if of appreciable size, seems to employ more instrumentation than the previously completed plant. Plant A makes a break-through in the application of instrumentation to a particular part of the process and Plant B accepts this and goes one step farther, while Plant C, anticipating Plant B, makes two or three more steps before Plant B is entirely leveled out.

Jan 9, 1958

By A. Boltax

The effect of cold work on the electrical and magnetic properties of solution-treated and aged Cu-Fe alloys was studied. The electrical resistivity of solution-treated and of aged Cu-1.7 wt pct Fe samples increased by up to 25 and 140 pct, respectively, follozcing a 55 pct reduction of area. The principle contributions to the increase of resistivity of the solution-treated and aged samfiles are examined. Measurements of the .saturation induction, coercive force, and stacking fault Probability are also reported. 1 HIS paper is the second in a series which examine the behavior of the electrical and magnetic prop- erties of Cu-Fe alloys. The first paper1 was primarily concerned with the effects of thermal treatment whereas the present paper examines the effects of cold work on solution-treated and aged Cu-Fe alloys. The effects of cold work on the transformation of the coherent fcc iron precipitate to the ferromagnetic form2 and the coercive force and remanence3 have already been described, but the unusually large increases in resistivity (up to 220 pct) which occlir with cold work have not been reported previously. EXPERIMENTAL METHOD The methods used for alloy preparation, heat treatment, and electrical and magnetic measurements are described elsewhere.1 The specimens, initially 4-in. lengths of 0.0625-in. diam wire, were cold worked by swaging in hardened steel dies. Following each reduction, the samples were etched lightly in hydrochloric acid to remove surface con-

Jan 1, 1962

By J. Price Wetherill

THE coal-seams that are worked vary from 32 to 100 feet in thickness, and occur at all angles of inclination, but are never flat for any great extent. They contain coal, slate, and an unsolidified coal, called dirt by the miners, in various proportions, a uniform seam of coal alone being rare. The upper walls are composed of conglomerate, sandstone, or slate; the first two hard and solid in texture, and withstanding the action of the atmosphere and moisture sufficiently well to offer but little trouble to the mining operations ; while the latter crumbles rapidly, owing, in part, to the decomposition of iron pyrites which it contains in large quantities, and in part to its own friable character, and requires constant care to avoid accidents to the men working below it, and to prevent its mixing with the coal mined. The floors are composed of slate. As in all mining operations, the. general system pursued is to reach with a permanent outlet such a point in the seam as will

Jan 1, 1877

By Albert J. Phillip

Jan 1, 1947

By H. W. Hitzrot

*Original Pages Missing From Book

Jan 5, 1954