Search Documents

By J. Richard Lucas

The coal industry, one of the great basic industries in the nation, plays a major role in the American economy. Coal is the principal fuel used in generating tremendous quantities of low-cost power so necessary to the nation. Two-thirds of the electrical energy and one-fourth of all energy consumed in the nation is produced from coal. Large-scale production of steel, cement, and chemicals is vitally dependent upon this natural resource. Because of extensive reserves and low mining cost, it is one of the few natural resources in which the United States is a significant exporter. During 1965 in excess of 500 million tons of coal were produced, almost 10% over the previous year; more than 50 million tons were shipped to foreign markets. The utility market gained approximately 8% during the year for a total of 242 million tons.

Jan 2, 1966

TO THE BOARD OF DIRECTORS AND MEMBERS Of THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the reports of the Treasurer for the year 1947 and the reports of the following standing committees Membership, Admissions, Papers and Publications, MINING AND METALLURGY (Magazine), and Library 75th Anniversary Celebration The founding of the Institute at Wilkes-Barre, Pa, in 1871, vas appropriately commemorated by a three-day Celebration, March 17, 18 and 19, 1947, at The Waldorf-Astoria, in New York City The Celebration had been scheduled for the preceding September but had been postponed, perforce, because of conflict with meetings of the Assembly of the United Nations The Celebration immediately preceded the Annual Meeting which was deferred from the usual February dates The proceedings took the form of a "World Conference on Mineral Resources " More than three thousand people, including eight hundred ladies, participated in the proceedings in one way or another Twenty-eight foreign countries were represented, some of them by five or six individual delegates Likewise, official representatives were designated by fifty institutions of higher learning in the United States A special 820-page Anniversary Volume entitled "Seventy-five Years. of Progress in the Mineral Industry,".(which

Jan 1, 1952

[ ]

Jan 1, 1938

By C. H. G. Bushell

The author maintains that selectivity in flotation depends in part on differences in rates of flotation. The rate of flotation should be directly proportional to the frequency of particle-bubble collisions. In this paper, it is suggested that floatable particles of the mineral must be distinguished from nonfloatable particles. Success in flotation is entirely a matter of selectivity. All minerals can be made to float. The problem is to make one mineral float and leave the others in the tails. For a typical ore, with all minerals naturally hydro-philic, a collector which is adsorbed by only one mineral and not at all by the others would give perfect separations. The hydrophobic, collector-coated mineral would separate cleanly from the remaining minerals. In practice, no such highly specific reagents are known. All standard collectors adsorb on most minerals to some extent, and selectivity then becomes a matter of extent of adsorption rather than adsorption on some minerals and not on others. Flotation is therefore a compromise process: if enough reagent is used to float all the desired mineral, the concentrate will be low grade; conversely, high grade concentrates can be attained only at low recovery. With many minerals coated with collector to varying degrees, selectivity appears to depend in part on each mineral floating at a different rate. The study of flotation kinetics is therefore a basic requirement to quantitative understanding of the process. REVIEW OF PREVIOUS THEORIES Before a particle enters the froth it must strike a bubble and adhere to it. Flotation rate will therefore depend on the number of particle-bubble collisions

Jan 1, 1962

By Persifor Frazer

For various reasons I have not specified the locality where the research indicated in the following pages was undertaken. It will suffice to say that it was on the grounds of a villa once remote from, but now completely surrounded by, its neighboring city, and in close proximity to an industrial establishment of great extent and importance manufacturing many kinds of steel articles and employing upwards of thirty chimney-stacks for power and process work. The problem was to discover the cause or causes of the mortality to trees and plants on the place, and to trace these causes to their origin. Before undertaking this experimental work, the bibliography accompanying this paper was compiled and studied. It appears from an examination of the careful scientific work performed by the ablest French, German, and English chemists during the last 25 years that they are unanimous in assigning the principal—in fact, the overwhelmingly predominant— cause of the destruction of vegetation to sulphur oxides, resulting either from direct oxidation of sulphur in oil of vitriol works, etc., or from the oxidation of the sulphur from the minerals associated with commercial coal. Schroder and Schertel showed in 1884 that the sulphates deposited upon the leaves are not injurious to the plants; and Freytag proved that free sulphuric acid could not be found

Jan 1, 1908

Mr. Brown : .That part of the Standard Company's plant which has been added since the publication of Mr. Leggett's paper, and is described in mine, renders the single-phase, alternating system, which Mr. Hale has called " unelastic," much more elastic than it had been. The original plant at Bodie was substantially the same as the Telluride plant mentioned in his paper. The machines came from the same shops, and were practically the same; but while the Telluride Company has changed completely to a polyphase system, the Standard Company has retained its original plant, but has belted on a directcurrent generator at the receiving end, thereby converting the water-power into electricity, electricity into power, the power into electricity, and finally again electricity into power for use in the mines. This is a roundabout course, to be sure, but it shows that there are possibilities even in the out-of-date single-phase system. The only point perhaps, that deserves particular notice with respect to the hoist is the fact that the rheostat, or starting-resistance, was not built originally

Jan 1, 1897

By Beeby Thompson

ALTHOUGH the exclusion of foreigners and private owners from participation in the development of the. Russian oil fields prevents first-hand information being obtained, both official and private news indicate a growing appreciation of the value of the country's oil resources. Notwithstanding the suppression of that initiative and energy which only ambition can adequately stimulate, the industry is progressing and exports of products are assuming an importance that cannot be disregarded as an economic factor in the world's oil business. The following notes and observations must be regarded mainly as the views of one who has closely followed the fortunes of Russian oil, when considering the changes that have taken place in geological knowledge and oil-field technique, which have so profoundly modified oil-fields methods. Russia is fortunate in having retained the services of. a few scientists and technologists whose devotion to science has superseded their personal inclinations, and to these few men must be attributed the slow, but nevertheless striking, progress that has been made. The productive oil fields of Russia are centered around the Caspian Sea which, with its connected river system, constitutes such an ideal means of internal distribution for products. From the group of oilfields of which the. city of Baku forms a center, oil is pumped to Black-town, a suburb of Baku, where all the refineries are situated. The next important group of oil fields is located in the Terek district near Grosny, where refineries are erected and the products are piped or carried by tank cars to Petrovsk for the internal Russian market, or sent to the Black Sea by rail. A third oil field is spread over the province of Uralsk, north of the Caspian, Sea, the main port of outlet being Gourief, at the mouth of the River Ural. In Trans-Caspia there are two oil-field centers, one near Krasnovodsk on Chelekan Island, and one in Central Asia at Ferghana. The product of the former fields is transported to Baku for treatment, while the output of the Turkestan field is refined and consumed locally, mainly by the railway.

Jan 3, 1925

By V. Vahatalo, E. Hakapaa, H. Tanner

Recently modernized, the surface plant of the Outokumpu mine in Finland incorporates a number of ideas meriting close scrutiny from this side of the Atlantic. The mining methods make extensive use of concrete in some unusual ways. Design of the headframe and surface plant represents the latest thinking of European engineers and includes an integral Koepe hoist. The deposit is in eastern Finland, province of North Karelia, 30 miles west northwest of Joensuu and at 60'44' N, latitude. Pyrrhotite, pyrite, chalcopyrite, and sphalerite mineralization occurs in a shear zone in quartzite near a body of serpentinite. Two lenses have a total length over 12.000 ft, with remaining reserves of the 3 to 4 pct Cu ore estimated at about 15 million metric tons.

Jul 1, 1955

By H. J. French

At the request of a committee of the Engineering Division,' National Research Council, a study of the properties of boiler plate at various temperatures up to about 900' F. (482" C.) has been instigated. The following is a report of preliminary tests made on two grades of 1/2-in. plate and includes a description of the apparatus used in the determination of the proportional limit. Detailed reference to- the many published investigations in connection with the properties of steel at various temperatures will be omitted from this report. Suffice to state that results obtained for variation in tensile strength, elongation, and reduction in area with temperature are in substantial agreement with the effects now generally considered to be correct. Comparison of proportional limit values with results obtained by other investigators will be found in the conclusions. Materials Used The steels tested were $1/2-in. (12.7 mm.) open-hearth boiler plate of firebox and marine grades. The specified tensile strength and the analysis for each are shown in Table 1. In the manufacture of this material, a

Jan 1, 1922

By J. A. Capp

For certain classes of electric railways a steel conductor is preferable to the oldcr atld more commonly used overhead trolley-wire. The third-rail presents a rather better appearance, because of the absence of an overhead structure; it is easily installed, cheaply maintai~ied, presents s large area for conducting and collecting the current, and is therefore particularly suitable for high speed and heavy service. With costs calculated on the basis of equal coilductirity in rail aud trollej-wire, the third-rail constrrictiol~ is cl~caper than thc overhead trolley. But the average interurban road will lise a trolley-wire of considerably less conductivity than would be obtained with the smallest size steel rail (about 60 lb. per pard) that mould ordinarily be used, and here the first clost of trolley construction would generally be less thau that of the third-rail. While no third-rail installation has jet bee11 in operation long enough to give figurcs of value, it ~vould appear that the cost of maintenance of the thirdrail construction should be less than that of the overhead trolley. This consideration, together with that of sightliness and adaptability (particularly in the case of terminals, yards and very heavy or high-speed service), will frequently off'set the higher cost of the third-rail construction and make it the preferable means of' conducting the current from thc generator to the car-motor. For the first third-rail installations, old track rails were used when obtainable, and these old rails were supple~rlented with new rails of standard T-section and composition. With the coming of the very heavy, high-speed service during the past few years, the resistance of these old and new standard T-rails was found to be so high that they mould not carry the high currents necessary without too great a drop in the line-potential. The rails would, therefore, have to be suppleme~~ted with addi-

Jan 1, 1904

By P. D. I. Honeyman

CHANGING trends in concentration, involving regrinding with the subsequent production of a finely divided, high-grade flotation product, presents a real problem to the modern copper smelter. In the treatment of such a material, handling difficulties are numerous and potential possible losses may be very great. In many plants, of course, preliminary roasting of the furnace charge remains an economical necessity. Under such circumstances, the operator has no alternative except to follow orthodox roaster reverberatory practice, though taking all possible precautions to avoid excessive dust losses and bad working conditions. In other plants, roasting is not only unnecessary but would be highly undesirable, and at best the charge would be merely dried before entering the reverberatory furnace. In the latter case the possibilities of raw charging loom large. The Miami plant of the International Smelting Co. handles the entire output of concentrates of the several mining companies operating in the Globe-Miami district. All of these companies produce a flotation concentrate which, at the Miami Copper Co. particularly, is all reground and is high in grade. In addition, the Inspiration Copper Co. ships a substantial tonnage of high-grade cement copper to the smelter from its leaching plant. Following the flow sheet of the original plant, all such material received was bedded, dried in Wedge furnaces and smelted in reverberatory furnaces. At times during the history of the plant it has been necessary to carry the drying operation further, to a partial roast, before reverberatory smelting. Since the charge contained over 80 per cent flotation concentrates, the handling of which in a dried condition was at best a dusty job, unusual precautions were taken to cut down dust losses. The Wedge furnace plant was equipped with a Cottrell treater and all hoppers and calcine cars were carefully designed to cut down dust loss in transferring the so-called calcine from hoppers to car and from car to furnace. In the furnace itself the dusting problem was a severe one. Arch erosion was very rapid and flues and waste-heat boilers rapidly filled up with a partly smelted flue dust.

Jan 1, 1932

IN THE early period of steelmaking, ingot structure and segregation presented no difficult problems. Crucible melting required very small ingots which, if properly deoxidized, gave little segregation, and a small inserted hot top prevented pipe. As larger ingots were poured [ ] from Bessemer and open-hearth furnaces, segregation, piping, and gas evolution became increasingly important. The first studies of solidification were made by Gathmann (l) and the Brearley's (2) who used stearine to show the effects of shrinkage and mold shape. Figure 78 shows a series of stearine ingots at various stages of solidification. These studies indicated that the liquid solidifies at a nearly uniform rate, starting at the walls and bottom of the mold and progressing inward, and demonstrated the formation of secondary pipe in big-end-down molds. Stearine illustrates the mechanics of solidification, and exaggerates pipe because of its great

Jan 1, 1944

By C. Chiou, M. E. Fine

While Gunier-Preston zones are growing in Al-4.2 pct Cu at room temperature, Young's modulus, measured dynamically, increases about 0.4 pct. From the change in modulus with time the exponent of time in the rate equation for growth of the zones was deduced to be %. From a comparison of the rates of increase of modulus at 1, 28, and 42°C an activation energy of 12 to 14 Kcal per mole is computed. These findings support the idea that copper atoms are supplied along dislocation channels to growing zones. In alloys the elastic constants will be functions of the distributions of the atoms. If the degree of ordering or clustering is changed, one expects a corresponding change in the elastic constants. During age-hardening of aluminum-copper alloys at room temperature, the copper atoms cluster on 100-type planes in the aluminum lattice forming

Jan 1, 1959

By Clarence Fenner

THE manufacture of optical glass is a process that demands careful regulation and control at all stages in order that satisfactory results may be obtained. The product, to serve its purpose, must meet stringent requirements, which can be assured only by careful procedure in manufacture. During the greater part of the time that a pot of glass is in the furnace, temperatures should be kept within certain rather narrow limits; a departure on either side is likely to be detrimental to the glass and may result in total loss. If the temperature during melting and fining be low, the melt is likely not to fine properly and the glass will contain quantities of bubbles, or "seed," or it may become milky and unfit for use; too high a temperature, on the other hand, is severe on the pot and may cause it to leak or cast stones, or the increased solution of pot material in the melt may acid to the color of the glass and decrease its transmission. Moreover, variations in the working temperature will mean variations in the amount of selective volatilization and, consequently, variations in optical properties from pot to pot. Furthermore, in the closing stages of furnace treatment, the melt is cooled until a certain degree of stiffness is attained, when the pot is withdrawn. The quality of the glass-its freedom from striae and bubbles-will depend in large measure on whether the temperature to which cooling has been carried is suitable. For each type of glass there is a narrowly restricted range of temperature to which each pot of the given type should be cooled before withdrawal. A quick and reliable method of measuring temperatures is, therefore, of the first importance. In the optical-glass work conducted by the staff of the Geophysical Laboratory during the period of the war, much attention was given to the clatter of determining what methods would meet the requirements. This article will deal with these investigations and with the application of the results to actual practice at various plants. At the. time that the work of the Geophysical Laboratory was begun at the Bausch & Lomb plant, each melting furnace was equipped with

Jan 7, 1919

By Carle Hayward

THIS work was first undertaken in the metallurgical laboratory of the Massachusetts Institute of Technology in 1907 by L. A. Dickinson, E. Phelps, and V. S. Rood, under the author's direction. They attempted to determine the diagram for the system Cu2S-NiS, but several inexplicable results were obtained. The following year, P. H. Mayer with Mr. Dickinson carried, on some experiments with nickel sulphide and found that the molten material slowly lost sulphur until it reached a composition corresponding to the compound Ni3S2, established by Bornemann.1 At this point the composition remained stable. The freezing points of the mixtures gradually fell off with the loss of sulphur. Since the above facts seemed to explain the erratic results obtained in the first experiments, Mr. Mayer with F. Jaeger attempted in 1910 to establish a correct equilibrium diagram for the Cu2S-Ni3S2 series. They prepared pure Cu2S and Ni3S2 and determined the cooling curves for various mixtures. The fusions were made in a platinum resistance furnace and the temperatures were measured with a platinum-iridium thermocouple connected with a Sullivan galvanometer. The curve was established for mixtures containing more than 40 per cent. Cu2S, but they were unable to determine certainly the direction of the curve beyond that point. Nothing further was attempted with this series until the present year, when the work was carried to a successful conclusion with the assistance of A. Butts, Jr., and E. H. Weil. The results of this work are given in the following pages.

Jan 1, 1914

By Gardner F. Williams

Chemically, the diamond is composed of the element carbon in its pure crystallized state. The diamond crystallizes in the isometric system, and the most common forms are the octahedron and dodecahedron, while the (24-sided) tetrahexa-hedron is not uncommon. Cube diamonds with beveled edges representing the combination 8 0 8 and 8 0 2 are occasionally found in the Bultfontein and Premier (Wesselton) mines at Kimberley, South Africa. The diamonds from various mines have distinctive forms of crystallization, or variations of the same forms, so characteristic that those familiar with South African diamond-mines and their products can determine positively from which mine any given parcel of diamonds has been obtained. It is not always possible to determine the source of each individual diamond, for similar stones are occasionally found in digerent mines; but these are exceptions to the rule. There is a difference in the luster, shape or crystalline form of the diamonds from the various mines that gives each mine some distinctive characteristic. In one mine nearly all of the crystals are sharp-edged octahedrons, while in another, dodecahedrons with rounded faces predominate. One might give no end of peculiarities of the diamonds from the various mines; but it will suffice for the purposes of this paper to state the fact that such distinctive characteristics do occur. From this observation it may be concluded that the diamonds in the mines of the Eimberley district, which occupies a small area (see Fig. I), did not have a common origin. The diamond is the most impenetrable of all known substances, and will scratch any other stone, or the hardest steel. It is a very strong reflector of light, and refracts incident rays more than any other substance except crocoite.l

Jan 1, 1905

By R. C. Philp, Allan Gibb

The term a matte " is applied to smelting-products so extremely diverse in composition and physical properties that it appears impossible to devise any generic formula to represent, chemically, the manner in which the varied proportions of the almost unlimited possible constituents combine with each other. Mattes produced in copper-smelting, in distinction from those produced in smelting-operations in which the recovery of cop per is secondary to that of other metals, cover a narrower range in composition. The copper-content of such mattes vary from 20 to 80 per cent., and even this range is much smaller in general practice since it is found advantageous, when possible, to produce mattes with about 50 per cent. of copper in the first operation. Further, it is unusual that arsenic or antimony occurs in copper-ores in sufficient proportions to form arsenides or antimonides in such quantities that they will separate out from the furnace-products, as is common in lead-smelting. Generally, the mattes produced in copper-smelting are composed mainly of copper (usually greater than 35 per cent.), iron and sulphur, the remaining elements being usually in proportions sufficiently small to allow of their treatment as impuritiee, rather than as essential constituents of the mattes. In modern practice of smelting copper-ores in blast-furnaces the tendency is to approach pyritic smelting as nearly as possible, the furnaces being low and the air supplied being largely in excess of that required for complete combustion of the carbonaceous fuel. Hence, the atmosphere of the blast-furnace thus used is usually oxidizing or nearly neutral, and, as a consequence, the reduction of metallic iron that was a necessary evil of former practice is of unusual occurrence in operations where the main object is the recovery of copper. Hearth-accre-

Jan 1, 1906

By T. V. Moore

IN many of the important problems of the petroleum engineer, it is necessary to know accurately the laws governing the flow of gas and liquid mixtures in vertical' pipes. Although much work has been done along these lines, no satisfactory solution to the problem has been found. A good theoretical discussion of the energy balance in a gas¬lift has been published-by Versluys.1 One of the most important factors affecting the efficiency of the flow of oil and gas mixtures is slippage, and in most of the experimental work that has been done no provision has been made for the measurement of this quantity. As Versluys pointed out, since there is no method now known to estimate it from the data usually taken; slippage must be determined empirically. This paper presents the results of some work carried on to, measure slippage in short experimental gas-lifts. As shown herein, slippage can be easily calculated in a vertical pipe carrying a mixture of oil and gas if the fractions of the pipe occupied by liquid and gas respectively are known. In this work, the fraction of the pipe occupied by the liquid was measured under a wide variety of conditions and the relationship between this fraction and other quantities, which are easily measured in ordinary work, was determined. It was hoped that the quantitative relationship obtained from this work could be used-for making accurate calculations in flowing or gas-lift wells, but unfortunately it did not check satisfactorily when applied to actual wells. Apparently flow in long flow pipes is mote efficient than in the short ones used for the experimental work. Nevertheless, it is felt that the data themselves are of interest; that the method of attack may be of value in future work and that the relationship derived between slip and the relative velocities is a contribution toward the solution of the gas-lift problem.

Jan 1, 1931

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935