Search Documents

Tunnels are being built around the world using TBMs and prefabricated segments or in situ concrete as linings. Clients demand high quality of these linings to guarantee a long-term stability and density of the tunnels. This paper describes the development and the use of segmental lining systems, including joints, important design criteria, installation procedures, possible mistakes and consequences, repair works and final results for different sites in Europe and around the world. The experience on these sites shows that damages may occur, if some essential aspects are not considered. These aspects include:parameters of the TBMs and back-up equipment such as fixation of jacking rams, movement of the back-up on the lining or ring reformer;parameters of the segments such as quality of moulds, quantity of reinforcement or structure of the joints; andparameters of the tunnel drive such as advance rate, ring-gap grouting or experience of the tunnel crew.All these aspects have to be considered very carefully in detail to get a good lining accepted in total.

Jan 1, 1999

By D P. Blair

Various analysis techniques are used to determine the nature of a large seismic event that was triggered by a mass blast in an underground mine. This event was recorded by surface accelerometer arrays whose output was doubly integrated using a stable filter to determine the dynamic displacements. The peak dynamic displacements during the blast were 0.09 mm, and during its latter stages, this blast induced a seismic event having a peak dynamic displacement more than ten times larger at 1.26 mm. Polarisation analysis, based on the complex covariance matrix, showed that the seismic event was caused by movement of a known underground fault, close to the blast, which radiated most of its release motion as a shear-horizontal (SH) wave. The change in frequency content with time for the blast and seismic event was initially determined using the Fourier-based reassigned S-method. This analysis showed that the large amplitude seismic event had frequency content significantly lower than that of the blast. Nevertheless, this Fourier technique still retains the problems associated with short time windows as well as the fact that most realistic signals are non-stationary. In order to eliminate such influences, the more recently developed empirical mode decomposition (EMD) was used to obtain the intrinsic mode functions (IMF) of the seismic wave propagation. The EMD vibration analysis showed that each IMF generally exhibited distinct frequency changes throughout the blast and a significant reduction in frequency throughout the subsequent event. It is shown that most of the energy of the seismic event is contained in IMF modes 2, 3 and 4 of the SH wave; the high-frequency first mode (IMF1) contains little energy. Such modal analysis is not possible using standard Fourier methods.CITATION:Blair, D P, 2015. Dynamic displacements from a blast-triggered seismic event, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 203–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A T. Spathis, M L. Lawlor-O’Neill

A methodology for the inversion of a scaled charge weight superposition model to predict peak particle velocity (PPV) has been examined. The inversion involves two steps: first simulated annealing is used to get an initial estimate of the model parameters; and second, these parameters are used as input to a quasi-Newton non-linear optimisation method, used to refine the value of the parameters. The methodology recovers the three required parameters (two charge weight scaling parameters and a time window width) and does this directly from a single production blast for a given point of interest. It has been tested on a synthetic example and recovered the input model parameters successfully in the presence of introduced noise with a coefficient of variation ranging up to ten per cent. Another test used the vibration measurements of three tunnel blasts monitored during the construction of the Citybanan tunnel in Stockholm. In this case, the three model parameters are found from one blast and for a given point of interest, and the PPV at the same point of interest is predicted for the second and third blast fired in the same vicinity as the first blast. The three blasts used different firing sequences. The predicted PPV limits use a confidence interval determined from the scatter in the peak levels obtained from the single calibration blast. The methodology was able to predict an upper bound for the PPV in 21 of the 26 tunnel blast vibrations studied. These predictions improve on a previous study involving the same model but which did not use the inversion process above. Given this reasonable success, further testing of the method on other data sets and alternative forward prediction models is recommended.CITATION:Lawlor-O’Neill, M L and Spathis, A T, 2015. An inversion method for the prediction of peak particle velocity in blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 97–108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A L. Zawadski, B G. Putland

"This paper discusses a method to build a calibrated comminution circuit model, using historic operating data and blend information that is useful for forecasting and optimising plant performance, as well as evaluating expansion opportunities. A preferred method for building a calibrated power-based comminution model is discussed and justified based on two case studies, offering low-cost and effective strategies to utilise existing information for the maximum possible benefit.The first example is the Lefa Gold Mine located in Guinea, West Africa operating a semi-autogenous grinding (SAG) and ball milling circuit with recycle crushing (SABC). Daily blend information and operating data was utilised to build and calibrate a power-based model of the comminution circuit. The least squares regression method was used to solve the SAG mill specific energy requirement and the operating work index (Wio) for each individual ore type. The calibrated model was used to evaluate expansion strategies to sustain throughput at higher proportions of fresh ore based on the proposed life-of-mine schedule.The second example is the Ok Tedi Copper-Gold Mine in Papua New Guinea operating a SAG and ball milling circuit (SAB). The circuit limitation would often shift between the SAG mill and the ball mill due to variable ore characteristics and feed blend. Typical SAG mill relief strategies, such as recycle crushing or secondary crushing, required significant capital expenditure and the potential throughput benefit would vary depending on ore type, making economic justification difficult. Daily blend information and operating data was used to build and calibrate a power-based model of the comminution circuit to identify ore types that might benefit from higher blast intensities to increase fines content, thus relieving the SAG mill limitation and increasing overall throughput without a major capital investment.Citation:Zawadski, A L and Putland, B G, 2016. Calibrating Comminution Models Using Operating Data to Forecast and Optimise Plant Performance, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 17–26 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By X Zhang, B McFadzean, C T. O’Connor, S Pikinini

The Platreef in South Africa contains one of the world’s largest reserves of platinum group elements. One of the major platinum group minerals (PGM) components in this ore is sperrylite (PtAs₂), which has been found to be slow floating compared to the other PGMs. In a study aimed at determining the reasons for the poor floatability of sperrylite and to improve its recovery, tests were carried out to determine the interactions of the mineral with a range of standard and novel collectors. Microflotation tests were carried out to determine the hydrophobicity of the minerals before and after adsorption of collectors. In addition, experiments were carried out to determine the enthalpy and extent of collector adsorption on the minerals and to investigate electrochemical interactions between sperrylite and selected standard collectors. The results indicated that poor collector adsorption was the major cause for the poor floatability of sperrylite. Sperrylite had both poor natural (14.5 per cent) floatability and collector-induced flotation recoveries, the highest recovery of 26 per cent being observed using PNBX collector at pH 9. Moreover, the rest potential tests showed that the interaction of sperrylite with standard collectors such as xanthates was poor. The decrease in potential after the addition of the standard collectors ranged from 7.9 mV to 24.9 mV under alkaline conditions. Furthermore, sperrylite rest potentials remained unchanged with a change in pH from basic to acidic, indicating its resistance to surface alteration. Surface alteration of the minerals is key for the chemisorption of collectors to take place on the mineral surface. This was further emphasised by flotation recoveries at low pH, where only certain collectors responded positively to a decrease in pH and these were shown to have undergone a structural change. This work has highlighted the difficulties associated with sperrylite flotation and provides some direction for future research.

Aug 24, 2022

By L Jackson, A Parbhakar-Fox, N Fox

"Characterisation of sulfide minerals (eg pyrite, sphalerite) in historic tailings can assist in determining whether there are economic benefits of reprocessing such materials using modern metallurgical practices. In addition, there are associated environmental advantages if the historic tailings are actively generating acid and metalliferous drainage (AMD). At the Old Tailings Dam (OTD), Savage River, Western Tasmania, 38 Mt of pyritic tailings were deposited from 1967 to 1982; consequently it has been recognised as an AMD source. Long-term management options considered for this site have included the establishment of either a water, hard-engineered or vegetation cover. However, due to geotechnical challenges posed and the lack of success demonstrated by previous pilot studies, these strategies have not been implemented. Instead, resolving the pyrite chemistry can allow for a first-pass assessment of whether reprocessing these tailings is a feasible option as part of a long-term management strategy for this legacy site.Tailings samples (n = 144) were collected across the OTD from up to 2 m depth from five facies (A–E), and four zones (1 to 4; defined by hydrological regime and grain size). These materials were subjected to acid-base accounting (ABA) and mineralogical evaluations to determine their geoenvironmental characteristics. Following this, 26 samples were selected for in-depth laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) investigations to evaluate pyrite chemistry across different tailings facies. The results revealed enrichment of Co and Ni in these materials. Specifically, Co content was up to 3.0 wt per cent, particularly within facies C to E, and Zones 3 and 4. Cobalt is recognised as a critical metal, therefore, reprocessing should be considered as a future rehabilitation option for the OTD, pending resource definition using established codes and practices.CITATION:Parbhakar-Fox, A, Fox, N and Jackson, L, 2016. Geometallurgical Evaluations of Mine Waste – an Example from the Old Tailings Dam, Savage River, Tasmania, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 193–204 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D Kentwell

For deposits where a full assay suite of elements/oxides is available and where several variables are critical to the evaluation of the deposit, it is desirable for the estimated block values of all elements/oxides to sum to 100 per cent of the weight per cent. This is difficult to achieve in practice and the estimation methods used need to be designed to minimise bias of the key elements/oxides by ensuring that block estimates are consistent with the individual assays and that the estimated totals are as close as possible to 100 per cent.This paper presents a case study of two domains within a magnetite hematite deposit, one with a high level of drilling classified as Measured and one with a lower density of drilling classified as Indicated. Several estimation methods were tested to evaluate their ability to maintain consistency of the proportions of each element/oxide and sum to 100 per cent. The following methods were evaluated: ordinary kriging, co-kriging, inverse distance and min/max autocorrelation factors (MAF) all as implemented in the Geovariances Isatis software.The comparisons showed that the MAF method produced the most robust estimates in terms of block totals and that grades and tonnages at the reporting cut-off were not significantly different between methods. At an individual block scale all methods produce artefacts that are less than desirable but can only be remedied by additional drilling.CITATION:Kentwell, D, 2015. Comparison of min/max autocorrelation factors, kriging, co-kriging and inverse distance block totals – a magnetite hematite case study, in Proceedings Iron Ore 2015, pp 465–474 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A Rantala, C Cruickshank, I Muzinda, O Haavisto, J Timperi

The production at First Quantum Minerals’ (FQM) Kevitsa Mine, located in northern Finland, commenced during the second quarter of 2012. Presently, the mine processes approximately five and half million tonnes of ore annually, producing nickel, copper and platinum group metal (PGM) concentrates. In order to support fast production ramp-up and optimise the performance of flotation thereafter, an extensive advanced flotation control solution was implemented by Outotec in collaboration with FQM Kevitsa.In addition to basic process instrumentation and process control, each of the 14 Outotec 300 m3 and another 26 cells, ranging from 20–160 m3, have been equipped with state-of-the-art systems providing froth image analysis and automatic froth speed control. Also, the flotation cell levels are stabilised with advanced feed-forward level control.The online analyser provides key feedback information of the process performance for the advanced process control (APC) system. Based on this information, APC system defines grades and recoveries according to rules defined by Kevitsa process metallurgists. This system executes the control strategies for optimising the production of concentrates.Throughout the implementation and support phases, specific and intensive attention was paid to ensure plant personnel gained full understanding of interacting with the system and how to incorporate their process experience and skills to optimise the APC strategy. This level of expertise is also a valuable asset in understanding the APC system’s contribution to the overall performance of the plant as well as providing the ability and confidence to define key performance indicators used for continuous assessment. The experiences and results from site achieved so far are discussed in this paper.CITATION:Rantala, A, Muzinda, I, Timperi, J, Cruickshank, C and Haavisto, O, 2014. Implementation of advanced flotation control at First Quantum Minerals’ Kevitsa mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 369–378 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By J Pan, Q H. Li, D Q. Zhu, C C. Yang, X Wang, Z Q. Guo

Al2O3 in natural iron ores generally occurs in goethite, kaolinite, gibbsite, hematite and iron carbonate. When the content of alumina in sinter increases from 1.11 per cent to 3.50 per cent, the reducibility of sinter decreases with the addition of four different types of alumina. When gibbsite and kaolinite are added, the low temperature reduction disintegration (RDI+3.15 mm) of sinter increases with the increase of Al2O3 content in the range of 1.5 per cent to 3.5 per cent. Furthermore, when adding pure reagent alumina, the increase of Al2O3 content in the range of 1.5 per cent to 3.0 per cent will increase the RDI+3.15 mm of sinter. The addition of ferric oxide–alumina spinel with the Al2O3 content in the range of 1.5 per cent to 2.5 per cent, also increases the RDI+ 3.15 mm of sinter. The influence difference is results from the change of the mineral composition and microstructure of sinter because of the occurrence state of Al2O3. Under the condition that Al2O3 content of sinter is 2 per cent, the porosity of sinter with kaolinite is 37.26 per cent, and the shape is irregular. When gibbsite and ferric oxide–alumina spinel are added, the porosity of sinter is about 16 per cent, and the pores are round. When pure reagent alumina is added, the porosity of sinter is 17.49 per cent, and the pores are regular and small. When kaolinite, gibbsite and ferric oxide–alumina spinel are added, platy calcium ferrite is mainly formed in the sinter, and some of it is columnar calcium ferrite. On the other hand, when pure reagent alumina is added, in addition to platy columnar calcium ferrite, acicular calcium ferrite is also formed in the sinter.

Nov 8, 2021

Xstrata CopperÆs Mount Isa Copper Operations is located in mineral rich north-west Queensland and is one of the largest sources of copper in the world. This world-class underground operation is planned to produce over 6.6 million tonnes of copper ore in 2007 from the X41 and Enterprise Mines. With an underground mining history of over 50 years and underground reserves of over 83 million tonnes at 2.6 per cent copper, mine planning for the future becomes an exciting challenge for the technical team due to the older nature of certain areas. The 1100 Orebody of the X41 mine was one of the first places that copper mining occurred, with its discovery in 1953 - 1954 and mining commencing in the 1960s. Sublevel open stoping mining methods have been employed since that time as the means of extraction, using a primary-secondary sequence to maximise stope turnaround time. Large Transverse Pillars within the 1100 orebody were not mined out in order to provide access for ventilation, power, orepasses and other services. The Panel Pillar, 4180XC and 4010XC pillars are three such Transverse Pillars in the 1100 orebody that will be mined as a final retreat. This paper discusses the technical challenges and issues associated with the extraction of Q390 stope, one of the stopes located in the Panel Pillar, and the design solutions to overcome these issues. Managing the exposure of backfilled stopes of variable fill strength, ensuring the stability of the crown, stope walls and drawpoints, managing vertical openings, re-establishing service networks, and stope filling are the critical issues given consideration for the final design of Q390 stope and other such stopes within a Transverse Pillar. Communication and coordination between the different departments in the mine are essential for the necessary work to be completed in a timely manner to bring pillar stopes into production.

Jan 1, 2007

By S J. Chen, N Jiang, Y S. Ding, F X. Li, D W. Yin, F Wang

This study assessed the deformation failure characteristics of rock-coal composites with different height ratios. Uniaxial compression tests were conducted using an acoustic emission monitoring system and XTDIC three-dimensional full-field strain measurement system. The results showed that with the increase in rock-coal height ratios, the uniaxial compressive strength of composite samples increased from 5.26 MPa to 14.61 MPa. The evolution of the deformation localisation zone of the composite samples is closely related to the initiation and propagation of the primary cracks in the coal samples. At the moment when the main fracture of the coal samples occurs, there is a large drop after the peak of the stress-strain curve of the composite samples, and the height of the rock samples increased to varying degrees, which indicated that the failure of the coal samples induced the rebound deformation of the rock samples. With the increase in rock-coal height ratios, the rebound deformation amount of the rock samples decreased from 0.042 mm to 0.008 mm, and the rebound deformation rate decreased from 0.210 per cent to 0.010 per cent. Meanwhile, the rock samples’ rebound deformation releases part of the elastic energy to act on the coal sample, further contributing to the destruction of the coal samples. Compared with single composite coal samples, the coal samples of the composite samples have much more failures. In addition, with the increase in rock-coal height ratio, the input energy density, elastic energy density, post-peak release energy density, and residual elastic energy density of the composite samples increased, the dissipation energy density decreased, and the percentage of pre-peak elastic energy density increased from 98.56 per cent to 99.86 per cent. These results revealed the deformation failure characteristics of rock-coal composite with different height ratios and provided a theoretical reference for understanding the underground dynamic rock failures.

Nov 29, 2022

The Myra Falls minesite, of Westmin Resources Limited, is located at the geographic centre of Vancouver Island, within the confines of Strathcona Provincial Park. The operation includes two active underground mines, II-W and Lynx, together with a modem 3650 1/d milling facility. Recent exploration successes will lead to the commissioning of a third mining area in late-1993 - The Battle/Gap Mine. These ore deposits are complexly metal-zoned volcanogenic massive sulphides of Devonian age, hosted in the Myra Formation of the Sicker Group volcanic assemblage. Three distinct felsic volcanic units are defined within the 450 metre thick Myra Formation. They are, from oldest to youngest, the H-W Horizon, the LMP Horizon and the Upper Rhyolite Unit. Massive sulphide mineralisation occurs throughout the property in the H-W and LMP Horizons. There are a number of orebody types, including polymetallic massive sulphides, polymetallic disseminated sulphides, zoned pyritic massive sulphides, elastic sulphide zones and stringer sulphide zones. Individual orebodies range in size from 10 000 tonne zinc-rich polymetallic lenses to the ten million tonne, zoned massive sulphide H-W main lens. The property has been in continuous operation for 26 years, producing over 13 Mt of ore averaging 2.2 g/t Au, 64.0 g/t Ag, 1.9 per cent Cu, 0.6 per cent Pb, and 5.6 per cent Zn. Current geological reserves stand at 12.5 Mt at a comparable grade, including 4 Mt of recently discovered high grade ore in the Battle and Gap Zones. Mining and milling methods have evolved over time to enable successful extraction and milling of these complex ores. Change is on-going with the recent conversion of the H-W Mine to large-scale bulk mining methods, and the development of effective computerised ore reserve calculation and mine planning tools. These changes, in concert with successful exploration techniques that led to recent high grade ore discoveries, have breathed new life into the operation and should assure its present and future viability.

Jan 1, 1993

Any Australian who knows of the poverty of the early settlers in the first few years following the arrival of Captain Arthur Phillip with his "first fleet" at Botany Bay must feel proud of the progress that has been made in the 174 years that have elapsed since that momentous occasionGFor all its attractive appearance as reported by Captain Cook and Sir Joseph Banks, the shores of Botany Bay and of Port Jackson proved most ,inhospitable, and the accessible country surrounding them anything but suitable for sustaining the life of the small settlement. It is well known that during the first 15 or 20 years the hardy colonists and un-tfortunate convicts were close to starvation on several occasions and were only saved by the arrival of supply ships, which were dependent on the vagaries of wind and current, and the hazards of the uncharted seas they had to -navigate-.When Australia was little more than a miserable penal settlement, Great Britain was one of the great-powers of the world, and the U,.S.A. was an independent nation with a growing degree of prosperity that even then gave promise of its mighty awakening to become, as it has, a e.olossus of industry and commerce,-and the. leader in living standards of the world to-day.Australia, from such a shaky, and comparatively recent start, has risen to a position in which its living standards rank very high in comparison with those of most of the nations of Europe and America. Exact com-parisons are hard to fix because of the wide variety of factors involved .but the Institute of Pab?Lic Affairs .(Victoria) places Australia fifthin the world, excelled only by the U.S.A., Canada, Sweden and Switzerland. The next best after Australia are the United Kingdom, West Germany and France.How we achieved such a high standard of living is a vast subject for study but some of the economic aspects of our climb from abject poverty to a position of near affluence can readily be identified.

Jan 1, 1962

By Y Li

An ilmenite ore from the Murray Basin was initially characterised using combined X-ray Fluorescence Spectroscopy (XRF), X-Ray Diffraction (XRD), Scanning Electron Microscope (SEM) and Electron Probe Microanalysis (EPMA) techniques. XRF analysis showed the ilmenite sample contained 58.7 wt per cent TiO2 and 26.2 wt per cent Fe2O3. Major impurities included: Cr2O3 (4.5 wt per cent), Al2O3 (2.7 wt per cent), SiO2 (1.9 wt per cent), Mn3O4 (1.5 wt per cent) and MgO (1.1 wt per cent). Manganese and magnesium were present as solid solution components within the ilmenite lattice while the elevated Al2O3 and SiO2 levels were due to separate aluminosilicate gangue minerals. Chromium was associated with discrete chrome spinel gangue phases of variable composition, (Fe,Mg)(Cr,Al)2O4. Quantitative XRD analysis of the sample identified rutile (12 per cent), ilmenite (11 per cent), and pseudorutile (67 per cent) as the main titanium-containing phases and chrome-rich spinels (seven per cent) as the major impurity phase. Minor quartz, aluminosilicates, zircon and monazite were also present. The ilmenite was mixed with synthetic graphite, pressed into pellets and reduced carbothermally in nitrogen at 1200 and 1400°C with C/O molar ratio of 1.2. Titanium oxide in the ilmenite was converted to titanium oxycarbonitride. Iron oxides were reduced to metallic iron. The Changes of impurities as a result of reduction was examined by SEM and EPMA analyses. Iron and chromium oxides within Fe-rich chromite were reduced to form a Fe-Cr-C alloy. Mg-rich chrome spinels were partly reduced at 1200°C. Zircon particles were not reduced at 1200°C, but were significantly reduced at 1400°C, with the particles becoming porous and the silicon being removed.

Oct 5, 2011

By J Pan, C M. Tang, D Q. Zhu, C C. Yang, S W. Li, Z Q. Guo

The short process of electric furnace steelmaking with direct reduction iron (DRI) as raw material is an important process for smelting high-quality and special steels. In order to prepare high-quality DRI, the pellets with basicity of natural basicity and 0.4 were prepared from magnetite concentrate (MR=0.09, MR=0.4) and hematite concentrate (HR=0.02, HR=0.4). Based on the HYL method, the gas-based direct reduction experiments were conducted under the condition of rich hydrogen (H2/CO = 2.6). The reduction index (RI), reduction swelling (RSI), cold compressive strength (CCS), and phase changes of the pellets were systematically studied. The results show that the RI of four kinds of pellets is greater than four in the temperature range of 800~950°C. For the magnetite pellets, at a fixed reduction temperature, the RSI increases and then gradually decreases, reaching a peak between 50 per cent and 80 per cent. Moreover, the RSI enhances with the increase of the reduction temperature. In general, the RI, RSI, and reduced CCS of the MR=0.09 pellets are better than those of the MR=0.4 pellets. For the hematite pellets, the maximum RSI decreases from 23 per cent to 17 per cent during hydrogen-rich reduction, while the compressive strength increases from 500 to 1070 Nꞏpellet-1. The main reason is that the glass phase generated by the increase of basicity adheres to the surface of hematite grains, hindering the contact between reducing gas and particles. As a result, the apparent activation energy is reduced, which is not conducive to the reduction process. In addition, the glassy phase attached to the hematite reduces the migration rate of Fe2+/Fe3+, resulting in a difference in the reduction expansion rate of hematite in the inner and outer layers of the pellet. Thus, concentric cracks are formed inside the pellets, the RSI increases and reduced CCS decreases.

Sep 18, 2023

By A L. Randriamanjatosoa, G Small, C Greet

In flotation simulation models, the effects of pulp chemistry other than pH are often ignored and reduced to particles hydrophobicity or contact angle, neither of which can be measured readily in real time in an operating plant. The flotation response of a given sulphide mineral is known to be influenced and can be improved by changing the chemical characteristics of the pulp during grinding and flotation. The on-line measurement of pulp pH, potential, dissolved oxygen, temperature and oxygen demand of a process stream was completed with the PCM® (Pulp Chemistry Monitor) developed by Magotteaux in this study. The data generated together with relevant plant operating parameters were used to construct an empirical model and simulate the metallurgical performance of the ore. The same approach was also applied to laboratory flotation tests data using various grinding media types. The flotation models better fit the actual data when the chemistry of the pulp is taken into account.CITATION:Randriamanjatosoa, A L, Greet, C and Small, G, 2018. Effects of pulp chemistry on plant and laboratory flotation modelling, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 423–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By L N. Loganathan

Risk exposure in tunnel projects is extremely high due to various factors such as variability of subsurface conditions, selection of inappropriate design and tunnelling methods, improper risk assessment on adjacent surface and subsurface structures and utilities, and inadequate contractual practices. The risks in tunnelling must be borne by the contractor, designer and the owner of a tunnelling project. There have been a number of improvements in the last ten to 15 years in the manner in which tunnel projects are developed and implemented in terms of their design, construction, financing and operations. One significant improvement has been the manner in which underground conditions and their risks are being managed. Owners are less willing to transfer the full responsibility to the contractor for managing the underground conditions, although this is a familiar manner in which underground major urban projects have been previously contracted and managed. The owners of tunnel projects in Singapore have advanced the risk management process for their projects through geotechnical interpretative baseline reports (GIBRs), geotechnical data reports (GDRs) and project specifications (PSs). This paper discusses industry practice and its development as well as the application during the preparation and use in Singapore on the Deep Tunnel Sewerage System (DTSS) and the Marina Coastal Expressway (MCE) project in Singapore. The DTSS trunk sewer is 48 km and ranges from 3.3 m to 6 m finished diameter up to 50 m below the ground. The underground conditions ranged from Old Alluvium, strengths of about 1 MPa to competent Bukit Tima granite, with strengths of over 230 MPa. The total route length of the MCE is about 5 km. About 3.6 km will be constructed underground, consisting of dual five-lane carriageways. The underground construction will be cut-and-cover, and 2.6 km will be constructed about 13 m underground, and 1 km of tunnel will range from 13 m to 24 m as the tunnel passes under a 420 m wide reach of Marina Bay, whose crossing will be constructed as a two-phase cofferdam.

Jan 1, 2008

By M BSckstr÷m

Acid rock drainage (ARD), commonly found in vicinities of sulfidic mines, possess properties capable of widely affecting the surrounding environment by acidification and heavy metal pollution. In most ARD treatments, various alkaline sources are used to neutralise the acid produced. Utilisation of highly alkaline fly ashes instead of raw materials is a cost-effective alternative, which lately have become increasingly popular. In laboratory batch experiments, neutralising capacity of fly ash was studied during 20 days. ARD was added to the fly ash once a day, for each increment the liquid to solid ratio (L/S ratio) was increased. At an early stage of the experiment (day 6, L/S ratio 12), the concentration of barium in solution unexpectedly increased by a factor of 50 (from 200 to 10 000 ¦g+l-1). This high concentration also sustained the following two days (L/S ratios 14 and 16) before dropping to the original level. pH showed a slight increase during these observations (pH 12.4 - 12.7). The phenomenon was also observed in a parallel and identical series. In addition to barium, aluminium and strontium clearly increased in the same manner, however not as much as barium. Furthermore, concentrations of chromium and molybdenum noticeably decreased at these distinct L/S ratios (12, 14 and 16). The behaviour of barium and subsequently strontium, aluminium, chromium and molybdenum is only partially understood. The decrease of chromium and molybdenum is suggested to be due to incorporation into the interlayer regions of hydrocalumite (Ca4Al2(OH)12(OH)2+6H2O), replacing the hydroxide groups, which also explains the increase in pH. Moreover, the increase of barium, strontium and aluminium could be attributable to dissolution of the silicate mineral celsian (Ba,Sr(Al2Si2O8)). Alternatively, barium and strontium increase could be explained by dissolution of a Ba,Sr(SO4)-solid solution and aluminium increase by dissolution of hydrocalumite or ettringite.

Jan 1, 2008

By P Holtham, K Duffy, W Valery, A Jankovic

In the face of increasing energy costs, limited water resources, more stringent legislation, and lower feed grades, the mining industry is searching for more sustainable technologies and practices. Metso Process Technology and Innovation (PTI) is undertaking a research project, ‘improving the resource and eco-efficiency of mining operations’, to help the industry meet these challenges. The project is investigating alternatives in mining and processing that reduce energy and water consumption, minimise emissions and waste, and maximise the value recovered from the deposit. The targets are to reduce energy usage by more than 30 per cent and greenhouse gas emissions by more than 50 per cent compared to current practice.Key areas of interest were identified across mining and processing operations. These were grouped into the following interrelated work areas for investigation: high intensity selective blasting, in-pit crushing and conveying, preconcentration, energy efficient comminution circuits and technologies, coarse particle flotation, and water recovery optimisation. Investigations have included reviews of industrial data, modelling, simulation, and laboratory and pilot scale trials. In some areas industrial scale trials will commence shortly. This paper discusses the investigations and key findings from the project so far; highlighting the possibilities for reducing energy consumption, water usage and carbon emissions. A particular mining process may incorporate any combination of the alternatives identified and requires tailored solutions based on a detailed understanding of the ore deposit, the process and local conditions. The focus is on improving resource efficiency; creating more value with less impact and consequently a better economic return from the available resource. Technologies exist today that can transform mining into a more efficient industry for tomorrow.CITATION:Duffy, K, Valery, W, Jankovic, A and Holtham, P, 2015. Resource efficient mining processes of tomorrow, in Proceedings Third International Future Mining Conference, pp 227–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By B Levasseur, C Olsen, E Ghasemian Langeroudi, F Larachi, F Safizadeh, C Gagnon

Gold recovery by the cyanidation process is often accompanied by the leaching of other species. This leads to the depletion of the level of free cyanide and oxygen available for gold cyanidation. The largest proportion of the consumed cyanide is diverted by the cyanicides (eg S, Cu, Zn, Fe, etc) into non-valuable complexes.COREMÆs Extractive Metallurgy team has been conducting a research program on the improvement of the gold cyanidation process. As a part of this program, the current study aims to investigate the effect of certain operating parameters on the reactions involved during preoxidation and cyanidation. Flotation tailings and single mineral samples such as pyrite, sphalerite and chalcopyrite, along with their different combinations, were analysed to highlight the influence of ore mineralogy on the operating conditions. The effects of different kinds of oxidants (oxygen, hydrogen peroxide, ferricyanide and ozone) and chemical additives (ammonium sulfate) were investigated.Experiments conducted in alkaline solutions reveal that mineralogy is a key parameter since pyrite, chalcopyrite and sphalerite react quite differently during preoxidation and cyanidation. A significant increase in sulfur dissolution, especially on pyrite, was observed by applying preoxidation. H2O2 preoxidation showed a positive effect on increasing sulfate formation, a desirable by-product from the cyanide consumption point of view. Preoxidation of synthetic ores with ferricyanide resulted in boosting thiosulfate formation. Tests conducted on flotation tailings from a polymetallic mine revealed that a short preoxidation increases the dissolution of the ore leading to higher gold recovery and lower cyanide consumption. Regarding the formation of thiocyanate, the most undesirable by-product of the cyanidation, ferricyanide and ozone were found particularly efficient to hinder their formation. Finally, the addition of ammonium sulfate during the cyanidation process showed some promising results in terms of both gold dissolution and cyanide consumption.CITATION:Ghasemian Langeroudi, E, Levasseur, B, Safizadeh, F, Olsen, C, Larachi, F and Gagnon, C, 2013. Optimisation of operating parameters for cyanidation of sulfide-bearing gold flotation tailings in order to prevent the impact of cyanicides, in Proceedings World Gold 2013 , pp 111-120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013