Search Documents

By L M. Foster, J R. Kellett, G A. McMah

The Great Artesian Basin (GAB) contains one of the largest reserves of fresh water in the world. The volume in storage is enormous, being estimated at nearly 65 000 million megalitres (ML). Development of this resource, dominantly for the pastoral industry, began in the late-1800s and quickly accelerated. With exploitation of the resource, artesian pressures declined almost as rapidly. This loss of head is a result of the total discharge from the basin and much of this discharge is waste of water. The waste through uncontrolled bores and inefficient distribution systems still amounts to about 75 per cent of all discharge. However, the volume in storage has hardly been depleted. The major concern is the effect of withdrawal on artesian pressures. Due to the size of the Basin, the relatively flat gradients and low permeability, the movement of water through the aquifers is extremely slow and independent of recharge. Hence, the normal concepts of sustainable yield (ie discharge should equal recharge) cannot be applied to the Basin as a whole as travel times do not allow for the effect of recharge to be seen away from the outcrop areas within management timeframes. The large volume in storage, though, can provide an extensive buffer to the impacts of temporary water needs. This effect should be considered when assessing the acceptability of fixed life projects such as mines and the extracted volumes from their operations. Identifying a sustainable yield involves balancing the acceptability of the economic, environmental and social costs with the associated discharge and fall in head, to arrive at an acceptable balance.

Jan 1, 2003

By Coppock BW

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972

The use of teleoperation in mining is increasing due to requirements to improve safety and reduce the number of people required to work in remote and difficult environments. We recently completed a project to develop a teleoperated control system for a rock breaker at an iron ore mine in the Pilbara region of Western Australia, with the objective of demonstrating the feasibility of remote rock breaking over long distances. This required controlling both the rock breaker and an array of pan-tilt-zoom (PTZ) cameras using joysticks. Controlling the cameras distracted operators from the primary task of controlling the rock breaker to position and fire the hammer. This lengthened task times as both the operator's attention and their hands have to swap between different control interfaces. In this paper, we present a novel design using human eye gaze as an interactive input for the remote camera control. It follows a simple and natural design principle: Whatever you look at the screen, it goes to the centre. A prototype system has been implemented by integrating computer vision based eye tracking technology, with the advantage of being real-time, robust and marker-less. We conducted a user evaluation, where users undertook a control task while obscuring the direct view of the working area and using a remote camera to transfer the live video stream as the visual feedback. Subjects were required to participate in the experiment using eye tracking camera control and traditional joystick control respectively. The statistical analysis of objective measures indicated that our novel eye tracking control significantly outperformed the joystick control. The results of the post-experimental subjective measures also revealed much higher user preference for using eye tracking control, which provides clear evidence that this design is a better interface for remote camera control in mining teleoperation settings.

May 1, 2010

By Mitchell D

In recent years the need to provide increased ventilation to improve environmental conditions rather than to dilute firedamp has led to increasing interest in the use of recirculation. Present UK mining law prohibits recirculation in ventilation, but it has been permitted selectively by exemption granted by Hm Inspectorate of Mines and Quarries. The conditions of use imposed by these exemptions to safeguard the safety and health of miners are examined in detail, dealing separately with primary and auxiliary recirculation systems.

Jan 1, 1988

By Gross A. E, Neville P. C

Over the last decade heap leaching with a cement binder has allowed the economical leaching of low grade gold ores of less than 2 grams/tonne. Despite the continued use of cement as an agglomeration aid, numerous leaching operations continue to experience channelling and blinding problems. This paper describes the development of polymeric agglomeration aids, Extract Ore 9760 and 9960, which when used as a partial cement or lime replacement can result in a higher rate of and/or a higher total gold recovery in plant evaluations. Extract Ore in combination with cement acts to produce a stronger agglomerate which results in reduced fines migration during leaching and helps prevent blinding of the heap. Both of these changes will give a more even flow of cyanide solution throughout the heap and improve solution contact efficiency within the ore. Polymeric agglomeration aid programs are now being used by heap leaching operations in three different countries. A summary of benefits identified at some of these operations are presented in this paper.

Jan 1, 1994

By Elliot B. J

Flash smelting is a complex and capital intensive technology. Although in use for 50 years the technology is still not well understood from a fundamental point of view and thus uncertainty is evident when significant change to the practice is necessitated. The application of effective design and process simulation tools has significant advantages when process change and improvement is required. Mathematical models have been used to simulate the processes occurring in the shafts of copper flash smelters. The present approach to flash furnace modelling differs from earlier work in that the burners were modelled in detail, the output from the burner model becoming the input to the shaft model. This paper serves as an introduction to the modelling process used to analyse the performance and provide a better understanding of the parameters applicable to the flash furnace at the Kalgoorlie Nickel Smelter.

Jan 1, 1992

The basic flowsheet for the Kalgoorlie Nickel Smelter and Kwinana Nickel Refinery are discussed in relation to the mineral components of Kambalda produced nickel concentrates. Both processes handle violarite and pentlandite satisfactorily but the smelter has limitations where high copper recovery is required and in its ability to handle magnesia containing minerals. While the latter can be more economically handled at Kwinana the limitations of this tolerance are discussed together with problems arising from treating pyrrhotite, pyrite and precious metals by the Sherritt Gordon process.

Jan 1, 1973

By Bourke J. H, Ashcroft T. B

Many changes have occurred in the world market for manganese over the last five years. Among these, the emergence of divided steel processes for the hot metal refining of pig iron is affecting the use of both ferruginous manganese ore and ferro manganese, at this stage particularly in the Japanese steel industry. Subsequent demand for higher quality manganese materials is promoting the use of thermally beneficiated products such as sinter. In addition, many processes are being developed for the direct smelting of fine manganese ores, of which plasma technology is the most advanced. Cost pressures and product quality requirements are encouraging pre- viously self sufficient countries such as The People's Republic of China and the USSR to import high grade manganese ores to supplement indigenous lower quality supplies. At the same time, Brazil has been provided with the impetus to convert its substantial reserves of ore to value added products.

Jan 1, 1988

By N Yarahmadi

Characterization of pore pressure is critical for appropriate design of tailings dams. Furthermore, if seepage rates through tailing embankments increase unexpectedly or become uncontrolled, undesirable conditions may prevail to progress piping or internal erosion that could lead to the dam’s instability or ultimate failure. A three-dimensional seepage analysis was performed on a tailings dam using finite element method to find the rate of seepage and pore water conditions in the embankment and foundation. The results were then compared to a conventional two-dimensional seepage analysis carried out on the typical cross section of the embankment and the field data acquired from the instrumentation system. Considering the monitoring data, comparison of seepage analyses results for the two and threedimensional models, showed that the results of the conventional two-dimensional seepage analysis are significantly underestimating reality. Relying on two-dimensional seepage analyses might result in underestimation of seepage rates and impact the safe operation of tailings dams. Similarly, unrealistic prediction of pore water pressure conditions, based on simplified seepage analyses, can lead to overestimation of the rate of strength gain of material and consequently safe embankment raising rates.

Jul 1, 2021

By Hawkins L. V, Seedsman K

A combined reflection seismic and magnetic survey off the south coast of New South Wales has revealed six distinct reflection horizons within the Lower Triassic- Upper Permian sequence, and has enabled the upper part of the Illawarra Coal Measures to be mapped in considerable detail. Large magnetic anomalies in the eastern half of the survey area appear to originate in the Gerringong Volcanic Sequence which forms the magnetic basement in this survey. Small residual anomalies in the western half of the area can be correlated with small scale faulting and folding in the uppert part of the Illawarra Coal Measures, as revealed by the seismic reflection survey. A synclinal axis striking at approximately 55¦ has been mapped near the western margin of the survey area, and areas of faulting and folding have been outlined by com- bined analysis of seismic and magnetic results.

Jan 1, 1969

This paper describes the application of a three-dimensional finite element modelling tool to help assess the stability of a highwall at a Central Queensland mine following the weakening of its base due to highwall mining. With traditional stability assessment techniques, likely failure modes are identified on the basis of previous experience and structural, sedimentological and geomechanical data and a mechanistic analysis of these individual modes is performed. The value of the full three-dimensional model over these traditional techniques is that it provides a coherent approach to assessing highwall stability without the necessity of initially deciding upon the dominant failure mechanism and gives a useful adjunct to the traditional tools. The three-dimensional model assumes the rock mass is made of elasto-plastic blocks, incorporating possible planes of weakness, separated by near horizontal joints. The model includes the relaxation of stresses due to the excavation of the highwall and incorporates estimates of blast damage near the highwall surface

Jan 1, 1995

A simulation of the fluid flow, minera- logical and chemical aspects of in situ leaching is being developed for application to the recovery of metals from unbroken, naturally jointed rock. The fluid flow aspect has been developed. The rock is assumed to have a double-fracture property. A major joint set is responsible for bulk flow of solution, while a minor joint set, intersecting with the major set, allows the solution to contact the reactive minerals. The two-dimensional fluid flow through the major joint set is analysed by a streamline model for a particular well pattern. The other important components of the model are described briefly.

Jan 1, 1984

The Hellyer deposit, hosted in the Cambrian Mt Read Volcanics, displays features typical of volcanogenic massive sulphide orebodies. These include a well developed stringer zone, metal zonation within the orebody, a polymict volcaniclastic sequence flanking the deposit and a hangingwall alteration plume in overlying basaltic pillow laves.Mapping and core logging is very detailed in order to extract as much data as possible from the deposit and its host rocks. A geological log suitable for direct computer input was adopted shortly after the deposit's discovery.

Jan 1, 1990

By Jones KW, McClelland RA, Denholm WT, Taylor RN, OÆShea J

Associated Tin Smelters, Sydney, are developing tin smelting operations in a prototype commercial SIROSMELT plant comprising two furnaces of 5 to 8 tonnes capacity. Features of the plant and its operation are discussed and results of its application to tin slag reduction and high-grade tin concentrate smelting are presented. Development work is still in progress but experience indicates that the technology has potential for lowering the costs of tin smelting and relieving constraints on grade and iron content of concentrate imposed by conventional technology.

Jan 1, 1984

In June 1992, the High Court of Australia recognised native title of the Meriam people over parts of the Mer Island in the Torres Strait as a form of common law. The Court also indicated that native title may have survived European settlement of the mainland Australia where it had not been extinguished by Governments and Aboriginal people have maintained their traditional connection with the land. The decision meant that two systems of land law were seen as existing side by side in Australia: ò one which derived from grants from the Crown under laws passed by Parliament; ò another which derived from the diverse laws and customs of the many Aboriginal groups in Australia.

Jan 1, 1996

By Blair J. R, Barrett J. R

In many underground mining applications where-dry fill is used, only a token acknowl- edgement of the fill properties is given. It is the aim of this paper to induce mining engineers to consider dry fill as an engineer- ing material rather than a mass to place in unwanted voids. Dry fill is generally cheap, inert and readily available, but it can still contribute to mining performance. In particular, the choice of the dry fill becomes more critical as stope sizes increase, controlled choked draws are used or pillar recovery introduced. Selection must be initiated from an evaluation of the role of the fill in the mining operation. In most cases the fill must be chosen before quarrying begins and an investigation must be made of available sources and appropriate quarrying methods. Some of the properties of fill are described together with evaluation techniques. A com- parison of placement conditions is limited by the complexities of material flow and degrada- tion: However, field and model tests can aid interpretation in these cases. Examples are given of aspects of dry fill selection and their incorporation in mining design.

Jan 1, 1973

By Amusin BZ

The concept of rigid or yielding bolts is discussed based upon support requirements for excavations of equivalent geomechanical behaviour. The concept of equivalent geomechanical behaviour is introduced for comparison purpose where the rock mass properties are varied for a given depth (stress) so that the deformation of the roof without any support remains constant = 300mm. A simple experimental theoretical analysis for a uniform stress field acting on an axi-symmetric excavation is conducted to establish roof bolt requirements under different conditions such as width of a given excavation, time of setting of support etc. Results are presented in graphical forms.

Jan 1, 1992

By Marshall B, Gee R. D

Geological data processing by machine enables'an increased rate of coverage, better supervision and control of field programmes, increased effectiveness of field operators, and vastly improved access to old and new field data. Even a system of restricted felxibility enables a mapping programme to be organ- ized and conducted independent of personnel changes, whilst elimination of much compilation time increases the rate of cover- age such that it relates to mode of transport and geological complexity rather than to personality factors. A machine is useful only if applied to tasks suited to its capabilities, and must be aimed at those types of mapping in which a limited number of attributes adequately define the problem, and the data is of a form suited to coding and is normally collected in sufficient abundance to make compilation wearisome. Machine systems are therefore unsuited to most types of lithological mapping and to most types of exploration in new areas, but have proved useful in many branched of cartographic geophysics (e.g. gravity and magnetics), and in cartographic Geochemistry.

Jan 1, 1969

By J K. Claflin, S R. La Brooy, A M. Claflin

Rotary kilns have been in service in the gold industry to regenerate carbon for 65 years. At the time oxide ores with gold head grades of 8 to 10 g/t were being treated. Carbon could be regenerated adequately at 650°C and solution losses were less than 1%. Forty years ago, research indicated that heavily fouled carbon from flotation circuits had to be held at 750 to 850°C for ten to twenty minutes for full reactivation (Avraamides and La Brooy, 1987), gold head grades were typically 5 g/t and solution losses typically 0.02 ppm – still less than 1%. In 2017 it was determined (Claflin et al., 2017) that a residence time of less than 1 minute at 750°C can be adequate to reactivate carbon fouled with organics sufficiently to achieve 0.005 ppm solution losses in a flotation tailings leach plant.With the potential for discovery head grades to drop below 0.6 g/t, solution losses of 0.02 ppm represent over 3% loss. Tight operation of the whole carbon circuit is required to keep gold solution losses below 1% going forward.There are alternatives to a rotary carbon kiln, e.g. vertical kilns of which the Minfurn, Rintoul and Combustion Air kilns are examples. The alternative kilns can be heated using electrical heating elements, induction, and microwave. These kilns can operate successfully under the right conditions, however, they are almost exclusively for small carbon throughputs and are not suitable for the large carbon advance rates that are required to process low head grade ore deposits. Large throughput carbon kilns are are almost exclusively fossil fuel fired rotary kilns and the subject of this paper. In the view of the principal author, a fossil fuel fired vertical carbon kiln is preferred to a rotary kiln, however, it is not currently used in the industry.Thermal regeneration of activated carbon has a major impact on gold recovery in the carbon circuit. The carbon kiln and associated equipment constitute 3 to 5% of the capital cost for an oxide processing plant and up to 10% of the capital cost if flotation tails are leached. Despite the capital cost and impact on recovery, the carbon kiln is often poorly selected, operated and maintained.Six years ago Ausenco embarked on the Carbon Kiln Initiative to reduce solution gold losses. This body of knowledge has been published in a series of papers culminating in this paper on how to:1. Select a kiln appropriate for the flowsheet;2. Maintain the kiln to achieve design operation; and3. Operate the kiln to minimise costs and maximise reactivation.CITATION:Claflin, J K, La Brooy, S R and Claflin, A M, 2018. Carbon kiln selection, operation and maintenance, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 251–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Liu Q, Siefken T. C, Misra V. N

Investigation of the differential flotation characteristics between arsenopyrite and pyrite in a ore concentrate have been carried out on a laboratory Leeds flotation cell. Experimental results indicate that some limited separation between arsenopyrite and pyrite is possible by differential flotation under the conditions of high pH and low pulp redox potential. The best performance in this testwork was achieved by using an oxidizing agent at pH 10.7. Of the oxidizing agents tested, NaOCI gave better oxidizing effect than KMnO4. It has also been observed that the pulp redox potential depends on the pulp pH value. At high pH values a hydroxide layer is formed on the arsenopyrite surface, which has the effect of a depressant on the arsenopyrite.

Jan 1, 1992