Search Documents

By J Harris, M Shi, S Vink, P A. Kirsch

Across the life-of-mine, water is both an essential commodity to mining, and one of the most significant hazards. In Australia, a land of drought and floods, availability of water is a critical strategic risk for mine sites and neighbouring stakeholders, with both insufficient water leading to curtailed operations and contested space, and extreme water closing operations through flooding of mine sites, transportation infrastructure and unplanned regulatory restrictions. In addition to these major strategic risks, water must be addressed in operational risk management activities in many different ways.This paper develops a set of categories for classification of water risks based on academic papers from the water in mining literature. These categories are applied to media content analysis of articles in International Longwall News (ILN) (an online coal industry news site) obtained with the search terms ‘water’, ‘rain’ and ‘flood’. Identified risks are discussed within the context of the life-of-mine. The paper uses these same categories to analyse the treatment of water risks in a new coal industry risk management body of knowledge called RISKGATE (http://www.riskgate.org, Minerals Industry Safety and Health Centre, The University of Queensland). The discussion of water risks in both INL and RISKGATE is compared and contrasted to pinpoint opportunities (and a roadmap) for further development of a specific RISKGATE water module for site-based operations. The media review also identifies areas for development of RISKGATE expansion topic(s) that would address other strategic water risks, eg severe weather events.CITATION:Shi, M, Kirsch, P A, Vink, S and Harris, J, ?2014. Water as risk in mining – media analysis and the RISKGATE body of knowledge, in Proceedings Life-of-Mine 2014 , pp 205–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By J Caron, M Athayde, F Lavoie, R Joyce

Decarbonisation has become a major challenge for the global steelmaking industry, turning towards new technologies aimed at carbon footprint reduction, which on its own accounts for approximately 9 per cent global emissions. The iron and steel industry represents a ‘hard to abate’ sector, where much of efforts are currently being deployed into initiatives aiming to decarbonise the ironmaking through the use of green hydrogen, carbon capture utilisation and storage and state-of-the-art operation of current technologies, while little efforts being deployed to find carbon-efficient solution to iron ore burden preparation, where high-grade iron concentrate will increase in importance to ironmaking regardless of the chosen reduction route. Quebec Iron Ore (QIO), a subsidiary of Champion Iron Limited (Champion), produces high-grade hematite concentrate with one of the lowest carbon global footprints. Still, QIO is partnering with its clients to the development of burden solutions to minimise CO2 emission, in the seek for a decarbonised steel. In a strong technological partnership, Binding Solutions Limited (BSL) has developed a novel, coldbinding technology to provide a cleaner, more cost-effective alternative to induration. The technology allows miners and steel producers to reduce Capex significantly and reduce energy consumption and CO2 emissions by 90 per cent. QIO and BSL have partnered to adapt the disruptive cold binding technology developed by BSL to QIO’s concentrate to produce a high-quality low emissions iron ore agglomerate. This paper describes the efforts taken to further develop BSL’s cold binding technology and its application to QIO’s high-grade iron ore concentrate to produce a hematite cold bonded briquette (hCBB) showing comparable performances with high quality seaborne fired pellets.

Nov 8, 2021

By G Harbort

The use of geological data for optimisation of operating plants has become a significant part of the modern process mindset. The underlying principle is to convert spatial geological data into metallurgical information to drive production and mine planning, blast design, blending strategies and plant set-up. Increasingly the process designer is required to interface with geological and mining staff to propose the best investment strategy for a project’s benefit.The geometallurgical model development for the Zafranal copper-gold project commenced in March, 2010, several months after the start of a major drilling campaign by AQM Copper Inc. The initial evaluation stage required review of historical Teck RC data to determine areas of metallurgical interest within the project. As drilling transitioned from RC to diamond drilling, core that was considered representative of the resource was selected and subjected to MLA mineralogy analysis. When coupled with sequential copper analyses this allowed calibration of an assay derived mineralogy model, allowing process concept options and a preliminary test program to be developed. This Phase 1 test program provided a preliminary process design, operating costs and anticipated concentrate grades and recoveries. Both this data and resource estimation were used to generate a preliminary Whittle pit optimisation based on maximising net smelter return, which in turn fed into a preliminary mine plan. The preliminary mine plan, in conjunction with geological logs and core results was used to develop a phase 2 metallurgical test program, where variability tests were conducted throughout the resource and composites formed to investigate specific years of the mine plan in locked cycle flotation. In addition comminution tests were modelled against geometallurgical domains allowing comminution components values to be calculated for 36?000 m of core. A flotation geometallurgical model was developed and incorporated into the resource model allowing concentrate grades and recoveries to be estimated on a block-by-block basis.

Sep 5, 2011

By B Stump

Reliable particle size analysis in minerals processing plants is a critical factor to the economic return of a plant. As recovery of valuable minerals is compromised for particles outside the optimal size range, effective and reliable particle size analysis is more crucial than ever, particularly in the current upswing of the global commodities market. Inefficient particle size analysis can lead to excessive over-grinding, thereby significantly increasing energy consumption and reagent costs, whilst negatively affecting process operation, thickening capacity, water recovery and tailings disposal.Australia’s first installation of a particle size analyser in Iron Ore has been monitored with great interest by the industry. Previously, manual size sampling at Rio Tinto’s Paraburdoo fines processing plant involved off-site sample analysis, with a turnaround measured in days. The Outotec PSI® 500 particle size indicator, commissioned in July 2009, takes approximately three minutes per line at site.The paper will include details on the following:• plant description,• sampling design,• PSI® 500 analyser functionality description, and• key learnings from site.

Jul 11, 2011

By J de Witte

When used in suitable ground conditions, rock bolts can have advantages over other permanent tunnel lining solutions. Permanent rock bolts offer flexibility in tunnelling profile and rapid rock bolt installation can enable time and cost savings. There are also disadvantages when considering the suitability of rock bolts for permanent support installations. These generally concern achieving the specified durability requirement over the specified design life. By investigating alternate approaches to rock bolt installation, quality assurance (QA), monitoring and design life it may be possible to alleviate some of these concerns.The design and construction benefits that can be realised through the use of rock bolts are primarily related to reducing project program time. This time reduction could be realised if rock bolts are considered as a permanent solution, with the installation being completed as a part of the primary excavation cycle. Any reduction of the program could allow direct and indirect cost savings and in the case of a major project, allow the revenue stream to be realised earlier.Currently ambiguity exists where the treatment of rock bolts as permanent support components is inconsistent with that of (often identical) ground anchors, as utilised in stabilising cut and cover structures. The ground support design process, implementation and testing are generally similar, though the acceptance of rock bolts as long-term support elements is treated differently to ground anchors in technical specifications.This paper discusses some of the benefits available through the use of rock bolts. It offers different solutions to the concerns surrounding durability, including alternate approaches to installation, Quality Assurance practices and monitoring solutions. The selection of an alternate design life is also investigated as another means of alleviating concerns around long-term durability. The paper will also provide an indication of savings that could be expected through the use of rock bolts as part of a long-term support system.

Mar 8, 2011

By A Yáñez, P Vallejos, R Grau, J Yianatos

In flotation cells, especially in large flotation units, froth management is a crucial variable that should be considered during the design phase or optimised to improve the performance of existing flotation circuits. This paper presents a simulation evaluation of the effect of launder design on the metallurgical performance of an industrial flotation circuit consisting of five TankCell® e630 (630 m3 ) cells in a Cu rougher duty. This analysis was carried out using a new industrial simulator, which was built on a wide database collected from many industrial concentrators. This tool is currently incorporated into HSC Chemistry® software and allows evaluation of the effect of launder design on mineral froth recovery, water recovery, entrainment, and other variables to be quantified. The industrial flotation circuit was evaluated under different launder design scenarios, considering an actual flotation circuit that includes TankCell® e630 cells for calibration and as a reference (baseline). Firstly, two different designs were evaluated in the full circuit: a standard launder design and a new launder technology. It was found that the new launder technology enabled improvement of the mineral recovery along the circuit, mainly for coarse particles, due to the improvement in froth mineral recovery. Next, the partial upgrade of the launder design along the circuit was analysed. Thus, the new launder technology was evaluated in the first and the last two cells of the bank. The results showed that upgrading the launders in different cells along the circuit delivered an increase in the final recovery with respect to the baseline, with a partial impact on the concentrate grade. However, these changes are less than those when evaluating the full upgrade scenario. A partial launder upgrade either in the first or last two cells of the bank showed similar final recoveries, but the latter enabled a slightly higher concentrate grade (about 1 per cent higher) to be achieved. Finally, the evaluation of launder design using the industrial simulator made it possible to estimate its effect on variables that are not commonly obtained from plant surveys, including froth recovery per particle size, collection recovery per particle size and liberation, gangue entrainment and bubble loading grade.

Aug 24, 2022

By D Morgan, K Jones

"In March 2015 Northparkes Mines (NPM) installed a process mineralogy facility on-site. The laboratory included a TESCAN TIMA scanning electron microscope (SEM) and was the first SEM facility to be commissioned on a mine site in Australia. While the initial intent of the quantitative mineralogy laboratory was to provide information to drive processing plant improvements, in practice, it has been utilised for so much more and is now serving as an integral link between departments on-site. This multidisciplinary approach to orebody knowledge is a new strategy for NPM whereby all parts of the value chain are aligned towards the common goal of achieving process efficiency and stability while still maintaining high throughputs. The NPM experience is presented as a case study to illustrate how on-site process mineralogy can drive a realignment in business strategy with a common goal of mill optimisation, stability and more realistic forecasting through orebody knowledge and information sharing between disciplines.Citation:Jones, K and Morgan, D, 2016. On-site Process Mineralogy - Linking Departments and Disciplines with the Common Goal of Increasing Plant Performance, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 149–156 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M Bond, R R. Hargreaves, G W. Booth

There are numerous causes of speculative mineral resource and reserve inflation. Traditionally, these are linked to issues of data accuracy or misinterpretation, the use of overly optimistic estimation parameters or assumptions, an absence of independent expert verification, or the simple pressure to increase company value, covert or otherwise. Owing to its subjective nature, classification of resources and reserves remains an opaque process. Of necessity, Competent Persons rely on personal heuristic interpretations, ideally underpinned by appropriate estimation and classification experience across commodity and deposit types. Whereas independent verification of individual resource and reserve statements remains impractical, publicly available data can be interrogated for potential category inflation, particularly when viewed with exploration expenditure statistics included in annual company reports. Abrupt changes in category tonnages and market capitalisation without concomitant expenditure can aid in outlier detection. Consequently, a comparison of common exploration and resource reporting parameters offers a basis for risk assessing classification robustness, over time. In this introductory study, an analysis of globally listed companies was undertaken over a multi-year period, examining base and precious metal projects in both preproduction and operational asset classes. From these, a series of exploratory decision tree trigger points were generated against which target companies were anonymously identified and risk-ranked.

May 24, 2023

By J Coombes, R Sterk

The efficiency of the Australian and New Zealand stock exchanges relies on a fully informed market: shareholders and investors are fully and transparently informed of all material information relating to the shares. These principles of transparency and materiality are similarly core to the Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the JORC Code). The JORC (Joint Ore Reserves Committee) Code also includes a principle of competency to ensure that the person providing the material information for public disclosure is suitably qualified and experienced.Since its inclusion into the ASX (Australian Securities Exchange) Listing rules in 1989, the JORC Code has continually improved and evolved in attempts to meet the market’s need for competent, transparent and informed disclosure. The quality and effectiveness of Public Reporting in accordance with the JORC Code is under constant challenge: some practitioners argue there is insufficient regulation, while others argue the need for greater self-regulation.This paper contributes to that discourse by exploring how well the Reporting expectations are met, and, whether Public Reporting in accordance with the JORC Code has a material impact on share-price movement.CITATION:Sterk, R and Coombes, J, 2017. Public reporting – new standards or no standards?, in Proceedings Tenth International Mining Geology Conference 2017, pp 423–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By R M. Yanamandra, M Kumar, S K. Tripathy, N Mangadoddy, P Sudikondala

Spiral concentrators are one of the flowing film gravity concentration devices used to beneficiate coal and mineral ores. The aim of the current study is to understand the particulate flow and separation performance of an LD9 spiral concentrator using a multi-phase Computational Fluid Dynamics (CFD) model. The CFD model utilises the Algebraic slip mixture model to simulate particulate flows. The model employs the Renormalisation group (RNG) k-ɛ turbulence models to resolve the fluid turbulence. Initially, the volume of fluid method was adopted to track the water-air interface. Simulations were then carried out at low (0.3 and 3 wt.%) and moderate (15 wt.%) solids concentrations. Multiple particle-phase representing particles of poly sizes (75–1400 µm) and multi-densities (1450–2650 kg/m3 ) were simulated to study the particle segregation on the spiral trough surface. The numerical predictions are compared with the literature performance data at a diluted pulp flow rate of 6 m3 /hr. The results were found in close agreement. Further, the same CFD model is used to study the change in pulp velocity, streamflow rates, and separation performance at increasing solids concentration. For the same density particles, Fine particles mostly show higher volume concentration in the middle and outer trough regions, whereas coarse particles show higher volume concentration in the interior and central trough regions. It implies that the fine particles mostly segregate towards the outer region, and dense particles segregate towards the axial column.

Aug 24, 2022

By G Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified low factor-of-safety due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the low factor-of-safety area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model. Electronic detonators and blast initiation systems were combined with advanced blast vibration modelling software to produce optimal timing sequences with predictable vibration outcomes. Although minimising vibration was the primary focus, blasting induced frequency was also a concern for the project team and therefore initiation sequencing was optimised to also avoid undesirable frequencies. Minor variations in ground factors (vibration transmission and attenuation) were noted, and therefore justified the inclusion of regular signature holes which allowed continual vibration model updates. Blasting results produced vibration and frequency measurements within allowable limits and closely resembled the predictive model. These positive results were achievable through the combination of electronic detonators, advanced modelling software and good onsite practices by engineering and on-bench teams alike. This project will remain ongoing as the pit progresses to deeper benches, and therefore the same methodology will be applied; quality and continual data collection, the use of electronic detonators, and optimisation via advanced vibration and frequency modelling software. CITATION:Wyartt, G, 2018. Vibration control blasting for low stability final walls, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 504–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By K Edwards, A J. J Mouton

Hematite represents the vast majority of iron ore exported from Australia as the development and processing cost of magnetite is generally seen as a barrier to the development of vast magnetite resources. However, a number of magnetite projects have attracted a significant amount of interest and investment from large Chinese steelmakers.This paper compares the relative merits of the development of Australian magnetite and hematite ore from the point of view of the steelmaker, taking into account the factors that influence the capital costs of the development of the ore types and the relative costs of operating the process plants to treat these ores. By modelling the relative operating cost for the production of hot rolled coil in China for the two ore categories, the paper demonstrates the economic drivers behind the Chinese steelmakers’ large investments in the magnetite resources of Western Australia. It does this by estimating the potential value of magnetite concentrate to the steelmaker in the event that the maximum potential is realised by operating the blast furnace with a 100 per cent pellet burden.Under the conditions described, it was found that direct reduction (DR)-grade magnetite concentrate could command a price premium over 62 per cent Fe fines of up to 46 per cent (December 2014 on a cost and freight (CFR) basis). The corresponding premium for blast furnace (BF)-grade magnetite concentrate is 17 per cent, which demonstrates the dependency on grade.The capital expenses for a 14 Mt/a concentrate plant is estimated at US$3.1 B for BF-grade magnetite and US$3.35 B for DR-grade, with operating expenses at US$45 and US$50 respectively. The corresponding free on board price for a break-even net present value is calculated at US$82/t for BF-grade magnetite and US$90/t for DR-grade. The minimum long-term iron ore price (62 per cent Fe) that would be required to underpin such a project is estimated at US$78/t CFR for BF-grade magnetite and US$68/t CFR for DR-grade concentrate.Apart from the financial benefits, it is demonstrated that the use of magnetite concentrate in ironmaking has the potential to reduce CO2 emissions by approximately 400 kg per tonne of hot rolled coil.CITATION:Mouton, A J J and Edwards, K, 2015. Magnetite – a higher-grade blast furnace feed and its potential benefits for the ironmaker, in Proceedings Iron Ore 2015, pp 613–620 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By W Newns

This paper describes laboratory and in situ tests and determines a set of parameters for stiffness and strength properties for a weak sedimentary rock mass, the East Coast Bays Formation of Auckland. The parameters derived are discussed in relation to peak strength and in respect of deformation limits associated with sequential excavate and support (SEM) or conventional tunnelling.

Mar 8, 2011

By Wang J, Ma Y, Jia H

The Hedong Gold Mine is located in the Yan(ai area, tihandong hroo%ill, e. China. It is an underground mine with an annual gold output of some 700 0(H) grams. The orebody is located on the edge of the Wanger Shan metamorphism zone, and the hangingwall of orebodies is thus defined by a prominent set of fractures. The proximity of the metamorphism zone and the inclusion of the fracture set ensure that both the orebody and the country rocks are unstable. The main orebodies dip at an angle of between 40 to 45¦, with a strike length of 160 metres and a horizontal width of 50 metres. Surface subsidence in the area is not permitted. Cut and fill mining is usually practiced. As the mining operation proceeds to greater depths, the ore grade is diminishing and it is necessary to find a more efficient stoping method. Sublevel open stoping with sequential extraction and filling of each sublevel has been designed and applied in situ. This new mining method is called 'sublevel open and fill stoping method' in the mine. Experience to-date is that new mining method is Satisfactory.

Jan 1, 1998

In practice a sampling solution is a compromise of many requirements: the sample should be representative; the sampling system should also be reliable, less than 95 per cent availability restricts the use of the assayed sample for process control purposes; no sample is the worst sample, and investment costs and installation space/layout are frequently a restriction. For instance, online X-ray analysers for process control introduce a delimitation error by the nature of X-ray physics. Thus only in special cases a relative accuracy better than three per cent relative, as one standard deviation, is achieved. A sampling system for process control needs not to be, as representative, for so many sample properties, as one for composite laboratory analysis samples. Sampling system maintenance is also an important issue. There are many sampling systems in the industry which have been difficult to maintain and are in disuse for lack of resources or incentives to keep them running. Pierre Gy developed the most generally accepted sampling theory. One of the main principles is that all particles in a one-dimensional process stream should have equal chances of being included into the sample. A correctly designed and operated transversing cutter comes close to this goal but has limitations in temporal representativity. For slurries an acceptable solution in many cases is to use a fixed vertical cutter(s) in a position where the slurry is well-mixed by turbulence and other means. For online analysis, reliability problems are mostly related to faulty design or installation of the piping system to the analyser. Properties of material processed, process flow sheet and piping details before and after the sampler have to be taken into account when deciding on which sampling arrangement is appropriate. Guidelines and some solutions to these issues are presented in this paper.

Mar 1, 2010

By F C. D Michelin

Blast fumes are a significant health risk to underground workers, containing several dangerous gases such as carbon monoxide (CO), nitrogen oxides (NOx) and ammonia. To ensure safe working conditions, workers are not normally allowed to re-enter a mine until the gases are cleared. To predict if gases can be cleared efficiently, simulations can be performed to estimate the gas levels following a blast. For accurate modelling, a calibrated airflow simulation is required in addition to blast-specific parameters such as the yield rate (representing the amount of gas released per kg of explosive) and the dispersion factor (representing how quickly the gases can enter the air stream from the explosive site). Those parameters are not easily determined, as they will vary from blast to blast. Many post-blast gas recordings on mine sites were studied and the correct parameters were determined to ensure an accurate gas simulation. The variability of the results was then analysed and correlation to known parameters is suggested. Finally, recommendations on how to determine the correct parameter are presented.

Oct 12, 2022

By P Klaric, N Swart, S Barnes

The recent advances in digital imaging technology, specifically around photogrammetry, have facilitated precision measurement in the difficult conditions encountered in an underground development mining environment. With the recent downturn in the resources industry, many mining houses have begun to focus on cost reduction projects and driving efficiencies. The application of digital photogrammetry has allowed greater insight into the development mining cycle and supported a focus on areas where efficiencies and cost savings can be achieved. Data collation, via digital image capture, can be completed with minimal disruption to the development mining cycle with analyses taking a nominal time to process and interpret. The result can be a stark visual representation of the result of blasting and associated activities of the development mining cycle. Many millions of dollars of benefit can be derived from understanding the impact of each component of the development mining process, with some of the biggest savings associated with conformance to drill design and the minimisation of overbreak during blasting. This paper will explain the image capture process, analyses and instigated improvement opportunities that were undertaken at a number of mine sites to improve efficiencies and drive savings in their development mining processes.CITATION:Klaric, P, Swart, N and Barnes, S, 2017. Digital imaging provides valuable insights into underground development mining, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 129–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By A Simmons, R Longey, D Brett

The South Deposit Tailings Storage Facility (SDTSF), located at Grange Resources Pty Ltd’s (Grange) Savage River mine in north west Tasmania, has recently begun construction. The facility will provide storage for approximately 37 million cubic metres of tailings, equating to approximately 20 years’ tailings storage.The SDTSF embankment will be constructed entirely out of waste rock won from mining operations, and will feature a flow-through drain constructed from alkaline, non-acid forming (NAF) waste rock. This provides Grange with an economical storage solution for waste management (both tailings and waste rock) and maximises available space on site. The outflows discharged through the alkaline rock ‘flow-through’ will provide a long-term source of alkalinity to Main Creek, subsequently feeding into Savage River. This will provide environmental benefits to the downstream ecology that has long been degraded due to the effects of legacy acid and metalliferous drainage (AMD), caused by historical mining operations.CITATION:Longey, R, Brett, D and Simmons, A, 2015. Integrated mine waste management – South Deposit Tailings Storage Facility, Savage River mine, Tasmania, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 343–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By M S. Cassola

It’s expected that the world economy will face a stable and continuous growth in the demand of iron ore, reaching more than two billion tonnes per year within the next year. After decades exploiting resources with high content of iron ore, now the industry faces the challenge to exploit and beneficiate more complex ores.According to the industrial practice, the flotation technology is one of the most important and effective beneficiation processes to deal with low-grade iron ores around the world. However, even with this, it is still necessary to search for new processing routes or promote the optimisation of the existing circuits.The broad application of this technology is an outcome that deeply relies on the proper selection of flotation chemicals specifi cally designed for each system. New collectors are in continuous development as flotation performance significantly relies upon their optimisation.The reverse iron ore flotation in Brazil, mainly constituted by haematite and quartz, uses ether amines as collector for silica minerals and caustic corn starch as depressor for haematite. The process selectivity is highly impacted by the features of the etheramine, such as:• mono or di-etheramine,• neutralisation degree,• chain length,• branched or linear chain,• the flotation pH, and• the size distribution of the flotation feed.This paper describes the experience obtained from laboratory and industrial trials on different ores, conducted to improve the selectivity and recovery in the reverse iron ore flotation by selecting the required collector for low-grade ores.

Jul 11, 2011

By H Yuan, H Tian, Y Zhang, Z Wang, C Wang

Submerged arc welding (SAW) is one of the significant metal-joining processes for manufacturing marine vessels, steel pipes, and offshore structures with high deposition rate and engineering reliability. Welding flux serves several essential functions, including atmospheric shielding, arc stabilisation, bead morphology control and weld metal (WM) refinement. Therefore, from a thermodynamic point of view, the focus for flux design and WM compositional/microstructural modification has been placed to elucidating the transfer pathways and mechanisms of major alloying elements, such as Si, Mn, Ti and O during welding. To this end, a thermodynamic model has been established to predict alloying element contents in the WM. Such functions are enabled by the physicochemical properties of the fluxes, which are inherently rooted in the nature of the fluxes. A unique yet systematical investigation, including physicochemical property changes and structural evolution behaviours, has been conducted over the wide range of fluxes applied to actual welding of EH36 shipbuilding steels. Combined with spectroscopic methods, structural behaviours of network formers such as SiO2, Al2O3 and TiO2 and network modifiers such as MgO, MnO and CaO have been illustrated. Viscosity and ionic conductivity have been found to be positively associated with the degree of polymerisation.

Aug 21, 2024