Search Documents

By A Sainoki, D Fukuda, K Shioya, C Zhang, M Sharifzadeh, T Yamaguchi, S Saydam, J Kodama, C A. Amagu, Y Fuji

In an open pit mining, ensuring stability of rock slope has been one of the major challenges. As the instability of rock slopes can results in slope failures; consequently, endanger the lives of workers, affect mining operations, and often lead to economic losses. Therefore, it is practical important to study the stability of rock slopes to ensure safe, smooth, and effective mining. The stability of rock slope of about 130 m height at Higashi-shikagoe limestone quarry, which has experienced slope failures four times since 1996, was assessed. The rock mass at the quarry is consists of mainly limestone, schalstein and slate rocks intersected by clay seams of about 70 m thick at footwall of the rock slope. Previously, the effects of limestone excavation at the foot of the rock slope and shear failure due to rainfall infiltration have been investigated. Although clay is widely known to plays a vital role in the stability of slopes in engineering projects including mines, but its impacts on slope deformation at the study quarry are not adequately examined. Therefore, the present study addressed the impact of presence of clay on slope deformation at Higashi-shikagoe limestone quarry by employing both field displacement measurements and numerical simulation. Firstly, surface displacements measured by automated polar system (APS) for over eight years were analysed to understand the overall characteristics of the slope deformation. The measured results show that the displacement gradually decreases with time. The maximum displacement of about 100 mm was observed at middle of the rock slope. Secondly, the effect of deterioration and plastic behaviour of the thick clay layer were simulated using two-dimensional finite element method (2D FEM). The simulated results reveal that the clay exhibited deterioration by water contact and plastic behaviour arising from mining activities at the footwall of the clay zone. Based on the characteristics of the measured and simulated results, it was found that the displacement induced by the effect of deterioration of clay is more noticeable at the north side of the quarry whereas displacement induced by excavation is quite significant at the south side of the quarry if clay behaves as an elasto-plastic material.

Nov 29, 2022

By H Kundapen, B R. Bolton, H Davies

The Ok Tedi porphyry copper-gold mine is located in the Star Mountains of Western Province, Papua New Guinea. Open-cut mine commenced in 1984 and is due to cease around 2010. The mine produces a total of 88 Mt of waste annually including 58 Mt overburden and 30 Mt tailings, which are discharged directly in to the Ok Tedi River. Mine derived wastes are transported downstream and deposited within the river channel in a variety of bar forms. The prevailing hydrogeological conditions including, velocity, competency, capacity, gradient, grain size and specific gravity, control the deposition and segregation of these sediments. Periodic exposure of the reactive sulfides to oxygen during fluctuations in the river discharge may result in oxidation, localised acid generation and liberation of metals into solution. To evaluate the significance of this issue, Ok Tedi Mining Limited initiated an investigation of the sediments deposited in the upper Ok Tedi River as part of its overall ARD Management Program. The specific objectives were to: evaluate the acid-forming characteristics of identified high sulfide river deposited sediments; characterise geochemically the waters in contact with sulfide-bearing river deposited sediments; map and monitor exposure areas and oxidation depth of deposited potentially acid forming (PAF) sediments; determine the depositional processes controlling sulfide distribution; and assess lag period, oxidation and metal release rates for the sediments. This work included the analysis of sediment and water samples collected on a 50 + 50 metre grid at six gravel/sand bars. The sediment samples were analysed for total sulfur, ANC, NAG, total sulfur and total copper. Water samples were tested for general water quality parameters, sulfate and a suite of dissolved metals including; Al, Ca, Cd, Cu, Fe-sol, K, Mg, Mn, Na, S and Zn. This paper presents the results of these investigations with particular emphasis on the geochemistry of the river sediments and associated contact waters.

Jan 1, 2003

By G Harbort, K Quan

Traditional engineering practice for concentrator design uses a mixture of risk minimisation options and capital minimisation approaches. Often this is based on the preferences and experiences of the engineers involved.A geometallurgical approach involves identifying primary lithology, alteration, and mineral dispersion patterns within a deposit to allow representative samples for test programs. This provides a method to infer from laboratory test results meaningful production data for larger amounts of the ore body. Geometallurgical models can be integrated into the resource block model and subsequent mine plan and can assist in predicting when difficulties in the processing route might be expected, allow adjustment of the design to compensate for these or provide an early warning system so that production forecasts can be more adequately developed. Simulation modelling is the process of creating a computer model of a real system based on mathematical logic. In simulated time, the model explores the randomness and chronological sequencing of events observed on real systems. The objective is to mimic the real system with sufficient accuracy to make predictions of real behaviour under experimental conditions. Amec Foster Wheeler often use the ‘discrete-event’ simulation modelling technique. This method is well suited for inclusion of the statistical variation of effects in unit operation, mechanical availability, throughput and operating strategy (based on historical operating data for equipment downtime), operating schedules and equipment capacity. The net result of the simulation model is an analysis that can quantify risks in terms of system performance and capital and operating costs.CITATION:Harbort, G and Quan, K, 2017. Concentrator design – standard engineering practice versus geometallurgy and simulation, in Proceedings MetPlant 2017, pp 195–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By I C. Carrasco, V G. Mirada, J F. D Domingo, F S. Leite

This paper investigates ore loss and dilution produced by rock movement in bench blasting. A total of four blasts, in which electronic detonators have been used, were monitored in Cobre Las Cruces Open Pit Mine (FQM Ltd) in Gerena (Sevilla, Spain). Rock motion has been obtained in 137 points of the free face and 6 points inside the block. Multiple liner regression has been applied to predict rock motion and estimate ore dilution as a function of hole coordinates, rock contacts, powder factor/hole, amount of explosive per blasthole, burden, spacing, hole length, stemming length, explosive energy, hole row, subdrilling, blast sequence, stiffness ratio, blasthole distance to free face, rock density and Young’s modulus. The model is statistically significant with a determination coefficient over 0.8. Rock motion measurements in 31 more points have been used to validate the model and to show a reduction in ore dilution.CITATION:Domingo, J F D, Leite, F S, Mirada, V G and Carrasco, I C, 2015. Dilution, ore grade and blast movement calculation model, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 71–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By L Gobbo

X-ray diffraction (XRD) provides useful information about the composition of an ore sample in terms of quantification of crystalline phases and amorphous content. The use of new, fast detection systems implemented in CubiX FAST industrial diffractometers creates the opportunity to use this technique in exploration and modern process control. Besides the chemical composition of iron ores, their phase composition is also an important factor for exploration, quality control and processing. In the analysis of iron ore, XRD can identify the phases containing iron, such as haematite Fe2O3, magnetite Fe3O4, and goethite FeO(OH), and any other mineral phases present, especially silicas. Quantitative analysis is possible by various classical methods such as straight line or polynomial calibration with standards, but modern quantification analysis techniques such as Rietveld analysis or full pattern autoscale analysis are attractive alternatives, as they do not require any standards. These methods offer impressive accuracy and speed of analysis. Another analysis technique offering great benefit to ore exploration and process control is cluster analysis. This technique greatly simplifies the analysis of a large amount of data, eg from drill core samplings, and automatically sorts closely related scans of an experiment into separate clusters and marks the most representative scan of each cluster as well as outlying patterns. This can facilitate multi-dimensional compositional mapping of ore deposits, identifying regions of favourable mineral composition and allows fast and reliable tracking of the process. It is the most economic procedure to have automatic data evaluation without involving any dedicated personnel in the process. Details of the techniques used, sample optimisation methodologies, results, data precision and limitations will be discussed. The approaches have enormous potential as an inexpensive, reliable tool, useful in the characterisation of iron ore materials in an industrial environment.

Jan 1, 2009

By E Widzyk-Capehart, T Bednarz, O Daud, N Cutmore

The interest of industry, in particular future mining, is pointing towards the use of novel visualisation systems to improve the operational efficiency of user interfaces. While the technologies used to enhance operators’ experience are advancing, the implementation of novel visualisation paradigms within mining operations is trailing behind other industries, particularly health and aviation. In this work, we present a number of initiatives and use cases of immersive virtual and augmented reality systems that can fit within the mining context. These ideas represent a step towards new platforms that might increase the efficiency and safety of mining operations through applications such as 3D panoramic video monitoring technology with annotated information coming from big data analytics and visual analytics processing engines. However, while the technologies are used in a variety of training settings, their application in the working environment is lagging behind. This paper presents examples of scientific visualisations that could be applied in a mining context to extend the possibilities of operators’ cognitive abilities and working efficiency. They are intended to foster a discussion within the mining community to move beyond the training realm and into the operational environment.CITATION:Bednarz, T, Widzyk-Capehart, E, Daud, O and Cutmore, N, 2015. Effective immersive visualisation systems for mining applications and beyond, in Proceedings Third International Future Mining Conference, pp 31–36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By K P. Crameri

The Beta Hunt orebody is situated on the south western limb of the Kambalda dome. It is one of the nickel occurrences in the area which fall into the category of æKambalda Style OrebodiesÆ. These orebodies are renowned as being continuous uniformly mineralised ribbons of nickel sulfide mineralisation. Interestingly, Beta Hunt does not conform to this notion of continuity and uniformity and is in fact highly irregular in its ore distribution due largely to the influence of post depositional structure. In an attempt to understand the ore distribution at delineation stage rather than development stage a detailed footwall topography model is created using all available drilling data. To augment this drilling data, the routine use of downhole EM and borehole radar has been introduced to provide data beyond the confines of the drill core to enhance the geological interpretation of the footwall topography and the distribution of the mineralisation. The implementation of a detailed footwall model and the use of downhole geophysics has proved to be very effective in resolving the orebody complexity issues. Ongoing development of the methods used will continue to refine the interpretation of the geology to enable more efficient extraction of the orebody.

Jan 1, 2006

By P Holtham, R Dunne, D Stoll

Flash flotation is a process designed to remove coarse, liberated, fast floating minerals from hydrocyclone underflow. Irrespective of liberation, coarse particles would normally remain in a grinding circuit until they are reground fine enough to report to the hydrocyclone overflow. Additionally, minerals of high density also report to hydrocyclone underflow despite being fine in size and/or liberated because hydrocyclones separate on the characteristics of both particle size and density. Dense particles continually reporting to the hydrocyclone underflow can lead to over-grinding and the production of ultra fine particles. These particles exhibit slow flotation kinetics and thus are difficult to float in conventional flotation circuits. Therefore, removing coarse, liberated particles from the hydrocylcone underflow by flash flotation has the potential to improve recovery and can improve dewatering unit operations and reduce grinding costs.The impact on the overall performance of the flotation circuit by removing coarse, fast floating minerals prior to conventional flotation is not well understood. Ultimately, predicting the overall recovery improvement provides the justification for the installation of a flash flotation cell within the milling circuit. This paper will describe attempts to estimate flash flotation recovery improvements to the overall circuit using kinetic data from simplified batch cell flotation tests combined with limn-based modelling techniques.CITATION:Stoll, D, Dunne, R and Holtham, P, 2012. Modelling the impact of flash flotation from batch cell flotation tests using limn, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 179-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By A L. de Ambrosis, S J. Clarke, R Bertuzzi, J Redelinghuys

The M2 Upgrade Project involved widening 15 km of the existing M2 Motorway, which is a key route in Sydney’s road network. The Norfolk Twin Tunnels in North Epping convey traffic over a 460 m length of the motorway. The project involved widening the twin tunnels to provide a third lane and breakdown lane in each direction.The widening of the tunnels was fundamentally different to other ‘greenfield’ tunnel projects in that the operation of the tunnel was maintained throughout construction, with motorway traffic permitted close to the excavation faces on a daily basis. The widened works had to integrate with the existing tunnel support, construction details, and mechanical and electrical infrastructure.The existing tunnel afforded the opportunity to review existing ground conditions in the tunnel. Exposures were mapped within the tunnel, and key design parameters were back-analysed from the original monitoring data to provide increased confidence in the assessed impact from the widening works.Traffic capacity of the tunnels was maintained by detailed staging of the works, and included the ability to reopen the tunnels at short notice.A permit to tunnel system was developed to manage the risks associated with re-opening the tunnel to traffic. A comprehensive suite of instrumentation was maintained to provide reliable monitoring data to support this process. Emphasis on the robustness and reliability of tunnel instrumentation provided increased confidence in the adequacy of the tunnel support being installed. The monitoring was routinely compared with design predictions to check the adequacy of the support measures being installed and confirm the design.The approaches and methodologies developed for the widening of the Norfolk Tunnels were effective in maintaining the safe operation of the tunnels throughout the two years of construction, and provide a framework for increasing the capacity of existing tunnel infrastructure in the future.CITATION:Clarke, S J, de Ambrosis, A L, Bertuzzi, R and Redelinghuys, J, 2014. Design and construction for the widening of the M2 Norfolk Twin Tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 591–602 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J Player, R de Vries, E Villaescusa, H Saw, R Hassell

The use of cemented rock fill (CRF) for support of open stope walls has increased in the Australian underground mines operations over the last five years due in part to its low capital cost. In open stoping the exposed CRF masses require adequate strength and stiffness, in order to resist the forces and to limit the displacement associated with movements in the rock mass surrounding the excavations. The CRF material preparation often involves the use of large particles, either from crushed rock or from development mining waste sometimes up to 1 m in diameter. However, the use of waste rock, which has a poorly graded particle size distribution may not achieve the required minimum target strength due to segregation and large air voids within the fill mass. This paper describes the optimisation of CRF strength by either crushing the waste rock or the addition of sand to the mix. Both methods increase the level of fines in the mix design. Cylindrical samples having 400 mm diameter and 800 mm heights were prepared for uniaxial compressive strength (UCS) testing. The UCS test was determined using the Western Australian School of Mines (WASM) large-scale static test frame. The laboratory results were compared with a database of large-scale CRF strength mixed without sand from a number of mine sites around Australia. The comparison shows a significant strength development in the CRF mixing with addition of sand for a given cement percentage. Due to the higher strengths achieved by the addition of sand and the crushing of the waste material these CRF types require less cement to achieve the same strength. This has the potential to improve the overall economics of open stope mining due to less dilution of the exposed fill mass.CITATION:Saw, H, de Vries, R, Player, J, Hassell, R and Villaescusa, E, 2017. Optimisation of cemented rock fill strength for open stope support, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By D Reid

Characterisation of non-plastic segregating tailings presents a number of challenges: the material cannot typically be sampled in an undisturbed state, remoulded samples exhibit different behaviour to undisturbed samples, penetration test interpretation methods suffer from uncertainty in their application to many tailings and the tailings gradation changes considerably over relatively small lateral distances and depth. In addition, the process liquor of many Western Australian tailings contains large quantities of salt and other dissolved solids, which can further complicate laboratory test programs. To provide an insight into the variability at a typical gold tailings facility, four gradations of the material were tested to obtain critical state parameters. Historic surficial tube samples were collated and organised by gradation to establish the range of densities typical after settling and air drying. These were then compared to laboratory-accessible densities. Finally, tube samples were tested in the laboratory to observe if the large-strain material behaviour was consistent with the inferred critical state parameters for similar gradations. Site pore fluid was used in the testing of the tube samples in an attempt to assess if the pore fluid modified the critical state conditions of the material.The tube samples tested all exhibited strongly dilative behaviour in undrained shear. Of the four samples tested, only one exhibited behaviour consistent with the inferred location of the critical state line relevant to the material’s gradation. The reasons for the unexpected behaviour of the other three samples include layering within the samples, the potential influence of large quantities of salt in the pore fluid and likely differences in the gradation of the fines components of samples taken from mid-beach and the decant area.CITATION:Reid, D, 2015. Observations on the behaviour of a gold tailings with hypersaline pore fluid, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 191–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By L Nicholls, A Parbhakar-Fox

Reprocessing Queensland’s historical copper tailings for critical minerals is an opportunity to circularise the state’s mining industry by converting waste liabilities into assets. Mine waste valorisation enables economic rehabilitation of legacy mining sites, improves environmental outcomes, and can establish a secondary resources sector that produces a sustainable supply of critical minerals to supplement growing global demands (Australian Government, 2023). The North-West Queensland Minerals Province (NWQMP) hosts numerous copper mines with known cobalt mineralisation (Degeling, 2020). Cobalt is a critical metal essential for green energy and battery technologies, however its global supply is at risk due to geopolitical and ethical concerns (Rachidi et al, 2021). Historically mining in the NWQMP has focused on copper, leaving cobalt to theoretically accumulate in the mine waste. First-pass geometallurgical characterisation of waste repositories by the Sustainable Minerals Institute identified Capricorn Copper as a key site for further investigation into cobalt deportment and recovery potential.

Aug 2, 2023

By P B. Hills, R J. Walton

Geotechnical instrumentation has been implemented as a key step for monitoring and optimising an engineered mine design for managing seismicity at the Beaconsfield Gold Mine. Measurements of displacement, stress change, ground control element load and seismic response of the rock mass allow for back analysis and calibration of critical parameters for feedback into the engineering design loop. Instrument clusters are installed in strategic locations prior to the commencement of stoping in order to determine the nature of the response of the rock mass to stoping. A selection of instruments including instrumented cable bolts and rod extensometers, resistance wire extensometers, hollow inclusion stress cells, vibrating wire stress meters and resistance wire extensometers are used to gather data through a data logging system. The rate at which data is recorded is adjusted to provide more information during periods of anticipated rapid change such as around stope firings or during periods of high seismic activity, and less information during periods of anticipated quiescence. The twofold purpose of the instrumentation is to calibrate the numerical modelling output which forms the basis of the engineered mine design, and to provide an alert mechanism where the behaviour of the rock mass is not what was anticipated, or where the impact of that behaviour may compromise the integrity of the engineered ground control system. The paper describes the location of instrument clusters with respect to stoping, the type of instruments employed and the method of data acquisition. It provides examples of results obtained and illustrates the way in which that information is used to optimise the mine design and manage seismicity.

Jan 1, 2008

By D Baas, D Bennett

This paper describes how Brisbane-based PanAust Limited develops process control strategies that are implemented at all operations and are used in functional descriptions for plant upgrades and new projects.The process control strategies are determined by operating management philosophies designed to maximise returns from the company’s assets.The approach is endorsed in the project planning and design phases to ensure facilities and equipment that form the major production assets are fit for purpose and capable of enabling the production managers and operators of the projects to maximise shareholder returns.PanAust’s process control approach has been to develop sets of process control standards which focus on two key areas. The first area covers hardware requirements and architecture, software objectives, control models and individual loop tuning methods. The second area defines control room layout, graphic standards and the alarm philosophy. The application of these standards in a new plant or upgrade decreases the time required to achieve design capacity and optimal performance.The PanAust process control strategy changes the operator’s role from one that controls a number of individual loops to one that sets the control objectives of the processing plant. To achieve optimal performance, all the process areas of the plant are analysed to identify opportunities to improve throughput, recovery and stability. Once a key opportunity is identified, a process control strategy is developed which defines the objective of the control, its functionality and how an operator will interact with it. After development of the control model the operators assist engineers to test and debug it. Once the model is robust, it can then be duplicated throughout the group and developed as a group process control standard.CITATION:Baas, D, Bennett, D and Walker, P, 2014. Developing process control standards for optimal plant performance at PanAust Limited, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 325–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By G J. Harbort, K Lam, C Sola

The relationship between the geology of porphyry copper deposits and their processing performance is an area of interest. Being able to predict comminution properties of the ore from physical characteristics and geological descriptions would allow an increase in the precision of capital cost estimates, operating cost estimates and throughput rates. This geometallurgical approach would reduce the requirements for expensive comminution tests.As the comminution circuit is the highest capital cost item in the plant and a possible throughput bottleneck, understanding the variability in hardness within the orebody is critical. A geometallurgical model allows calculation of ore hardness values in mining blocks from ore characterisation data. This model subsequently uses a combination of simulation and power-based approaches to relate ore hardness and flotation feed size to grinding circuit throughput.This paper reviews the geometallurgical models developed for seven porphyry copper deposits and discusses the strengths and shortfalls of the methodology and similarities and differences between the different deposits.CITATION:Harbort, G J, Lam, K and Sola, C, 2013. The use of geometallurgy to estimate comminution parameters within porphyry copper deposits, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 217-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By F K. R Klose

Malmberget is a sublevel caving mine owned and operated by Luossavaara-Kiirunavaara Aktiebolag (LKAB), a Swedish state-owned iron ore mining company, in northern Sweden. The mine has an annual iron ore production of approximately 15 Mtpa. The current strategy foresees an expansion which will increase the mine’s depth considerably. Ventilation and air conditioning modelling for the planned expansion is ongoing. One of the most influential parameters for ventilation planning anddesign for a deep mine is geothermal gradient, which is crucial for the design of the refrigeration system. It is determined through virgin rock temperature (VRT) measurements carried out at various depth below the surface. This paper details these measurements and the determination of geothermal gradient for Malmberget Mine for the expansion study, which were necessitated by thelack of information for the focus depth and area.

Oct 12, 2022

By W F. E Ouedraogo

This study data has been collected on a three-month period from November 2020 to January 2021 and based on three different pits: Vindaloo Main, Vindaloo Central and Bouere. Both pits having specific geotechnical and geological properties. Vindaloo Main, VIM, and Central, VIC, have the same mineral composition as volcanic tuff with felsic intrusion or monzodiorite, both rock mass is fractured with small joint. Geotechnically the uniaxial compressive strength UCS between 200 to 300 Mpa, Young’s Modulus 110 Gpa and Poisson’s ratio between 0.1 to 0.2. Bouere pit is basically made of volcanic tuff stock works as intrusive, UCS between 200 to 300 Mpa, Young’s Modulus 103 Gpa and Poisson’s ratio between 0.2 to 0.3. The first step of this study was to collect various data from mining operations around the drilling and blasting inputs. This was based around the different scenario of drilling parameters and the outcomes on the blasting, and how they impact load and haul operations and productivities of excavators from the heave to the last flitch. In most cases surface photos of the blast do not represent the overall fragmentation in the blast volume. Photos of the different flitches will not show only the effect of blast, as the loading operation generating more fragmentation by applying weight on the muck pile. Then the record of the different material uses for feeding. The last part of the analysis is the physical data from process plant such as particle size, throughput rate, both for the crusher and the mill, per pit and material and the specific Bond Work index (BWI). Fine particle quantity production is also a key point as is one direct indicator of milling performance. In overall, making link to BWI can influence at each stage of the mining to the processing operation. Drill and blast constitute a high cost in hard rock mining and trying to reduce these costs without an overview of all the integrated processes and context could end up by cost relocating to other activities in the process. However, the cost associated to size reduction builds exponentially as the particle size becomes smaller.

Jun 22, 2022

By G Hancock, A Kemp, I Taylor

The mine site is situated south east of Port Hedland in the Pilbara region of Western Australia. A detailed engineering design was undertaken for six irregularly shaped waste rock dumps at the site. The design was undertaken to ensure long-term stability of the dumps and optimise material movements for closure construction. The Watershed Erosion Prediction Program (WEPP) and SIBERIA landscape evolution modelling was undertaken for the landforms using regional and site-specific material characteristics to provide an indication of the maximum allowable slopes and corresponding slope lengths for long-term stability.The majority of the waste materials present in the waste rock dumps are considered likely to be subgrade banded iron formation (BIF) and chert, which is generally competent material. The presence of a large number of dolerite dyke swarms indicates appreciable volumes of dolerite were produced as waste from the pits. Geological records also indicate that the dolerite is logged as being heavily kaolinised in the geological logging, hence kaolinite is very likely to be present within the waste dumps on-site. This material has an elevated risk of being highly erodible/dispersive. Clays and shales are also likely to be present in the dumps and are considered to be less competent material (relative to the BIF/chert).The final design configuration of the largest existing ‘unplanned’ waste rock stockpile is compared to a hypothetical continuous ten degree outer embankment alternative. This paper will present a brief description of the alternatives for closure of three waste dumps in close proximity to each other and how the detailed design based on site-specific materials and conditions compare to an alternative approach blankly assuming that most materials will be erosionally stable at less than ten degrees.CITATION:Kemp, A, Taylor, I?and Hancock,?G,?2014. Landform design for Pilbara mine site – why plan and design waste rock dumps for closure based on site-specific conditions?, in Proceedings Life-of-Mine 2014 , pp 47–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Y Li, S Ramazan, E Topal

A mine waste dump progression plan can provide a clear outlook of the mining operation. To produce such an output requires detailed placement schedule of the mined material, including the volume (or tonnage) and the allocated dumping location. However, current practise mainly focuses on the ore production, over-simplifying the waste material scheduling. As a result, a rock dump is often treated as a single point in long-term planning, making it difficult to predict the waste dump progression pattern over the life-of-mine. Without such a guidance, it is almost impossible to carry out progressive rehabilitation on the waste rock dumps. The lack of dumping schedule could cause delay in development construction, ie tailing storage facility and run-of-mine pad. Other downstream effect due to the over-simplification is inaccurate estimation of required truck hours, which could have huge financial impact on the operation.In this paper, mixed integer programming (MIP) models of different objective functions, ie maximise truck productivity by minimising the overall haulage distance, minimise required truck deviation between adjacent years, and a hybrid between the two objectives, are utilised to generate the long-term optimum rock placement schedules under the criteria of satisfying site specific conditions. All three MIP models are implemented in a large scale open pit mine. The numerical solutions from the models forms three different rock placement schedules, based on which, the yearly truck requirements are easily calculated and compared. The graphical results show the three corresponding waste dump progression patterns over the life-of-mine, providing the optimised long-term forecast of the operation.CITATION:Li, Y, Topal, E and Ramazan, S, 2014. Optimising the long-term mine waste dump progression and truck hour schedule in a large-scale open pit mine using mixed integer programming, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 335–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J Crosbie, M Lord, R Bitencourt, P Defferrard

The MMG Century mine, which is the largest zinc/lead mine in Australia, began operating in 1999 and ceased mining from the open pit in July 2015, with processing completed in early 2016. Closure plans were developed from 2006, and detailed planning for closure commenced in early 2011 with the appointment of a dedicated closure planning resource. The site will continue to be managed during the active and passive closure phases to complete rehabilitation commitments and demonstrate that closure completion criteria have been achieved.Completion of the mining/processing phase of the project provides an opportunity to reflect on successes, missed opportunities and lessons learnt with respect to planning and execution of mine closure. This paper highlights examples of success at Century and also identifies key learnings and areas for improvement in progressive closure outcomes. Specific examples examine mine planning and execution involving bulk movement of waste rock and construction of permanent waste encapsulation landforms. The paper also provides recommendations for other sites that are planning for closure.Decisions made during the operational phase of the project life can result in a significant increase in closure liability and reduce the likelihood of achieving lease relinquishment. Likewise, it is of paramount importance to assess the consequences and thoroughly understand the risks associated with changes or deferral of closure plans, progressive rehabilitation targets and closure related key performance indicators.CITATION:Lord, M, Bitencourt, R, Crosbie, J and Defferrard, P, 2016. Closure planning lessons Learnt from the Century mine, in Proceedings International Mine Management Conference, pp 207-216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016