Search Documents

Obvious differences in mineral deposit types occurring in Outer Melanesia and Northern Chile can be related to the sub- marine-dominated nature of volcanism in the' former area and the subaerial-dominated nature in the latter area. Subtle variations in subvolcanic epithermal-porphyry ore systems between the two areas probably result from differing ore fluid compositions. Hydrother- mal convection cells in Outer Melanesia will be seawater-dominated, consequently rela- tively high salinities and chlorine contents will characterise the ore solutions. Trans- portation of metals as chloride complexes is likely and the ease of seawater sulphate reduction to sulphide in the ore systems will lead to widespread, sparse dissemination of sulphide minerals. Relatively low grade por- phyry copper deposits will typify these ore systems. In Northern Chile hydrothermal convection cells will usually be dominated by meteoric waters. Consequently ore fluid salinities are likely to be lower and chlorine will be less abundant. Under these circum- stances transport of ore metals as bisulphide complexes could be important. Boiling and loss of H2S gas from these fluids would lead to rapid precipitation of metals and higher grade deposits. Erosion rate is a very important factor in the preservation of ore deposits and this may be the major control on the richness of a metallogenic province. The abundance of mineral deposits in the El Salvador region of Northern Chile compared to Fiji is probably a function of the much lower rates of erosion in the former area.

Jan 1, 1987

By M Thomas, M Caccetta, C Laukamp, A Hacket, M Jones, A Rodger, M Verrall, R Hewson

A mineral systems approach was used to interpret precompetitive airborne mineral mapping geoscience data for iron oxide copper gold (IOCG) exploration in the Starra area, Eastern Succession, Mount Isa Inlier. Selected minerals were chosen to map possible source rocks/fluids as well as intersecting structural/fluid pathways that could have transported mineralising fluids into domains of contrasting rocks/fluids where there was potential for physicochemical gradients to precipitate metals. Ferric and ferrous iron contents and white mica abundance were useful mineral criteria to identify theMount Dore Granite of theWilliams-Naraku Batholith as a potential source of æoxidisedÆ fluids rich in Fe, K and potentially Cu-Au. The Mount Dore Shear Zone (MDSZ) intersects the western margin of this granite with the highest contents and changes in composition of the white mica are peripheral to this contact within the granite. This together, with the fact that the entire N-S length of the MDSZ in the study area (~16 km) is abundant in white mica are evidence of K-rich fluids had preferentially moved along this pathway. To the south, the MDSZ intersects a domain comprising massive ironstone bodies as well as numerous graphitic horizons. This interpreted æreducedÆ domain is well mapped using the æopaqueÆ mineral products, as well as by white mica, which is pervasively developed and extends 2 km either side of the MDSZ fault into the meta-sedimentary sequences. The chemistry of this white mica also changes progressively away from the MDSZ, becoming more Si-rich (longer wavelength) towards the contact with massive ironstone bodies in the west and the graphitic units in the east, both of which represent sites of known Cu-Au mineralisation. Beyond these contact zones of interpreted æoxidised fluidsÆ with reduced rocks/fluids, there is either a rapid change to Si-poor white mica and/or no white mica developed, ie major æchemicalÆ gradient change. These mineral mapping results provide evidence for a direct link between possible source rocks and sites of IOCG metal deposition as well as extending the associated alteration zonation which had previously been mapped/published at the metre-scale to the kilometre-scale. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Mining operations have been carried out at Mt. Lyell for the past century. Until the 1970's the location of the mines in relation to the surface topography has enabled the mines to drain their copious inflows of water by gravity. Deeper mining has forced the Company to undertake pumping of increasing inflows of water. A major pumping facility is being established near the base of the known ore reserves with a view to serving the future requirements of the mines. The system has a design capacity of 600 litres per second. Run of mine water will be treated in Vertical Flow Settlers to produce clear water and thickened mud, each of which will be disposed of separately. The clear water will be pumped by six 1000 kW conven- tional centrifugal pumps. The thickened mud will be removed by a Hydraulic Displacement System. The rising mains for both the mud and the clear water are stainless steel cased bore- holes.

Jan 1, 1982

By Gupta A, Hall ST

The grinding characteristics of quartz which is normally associated with gold bearing ores in Kalgoorlie area was examined in a stainless steel laboratory size ball-mill in the presence of inorganic and organic surface active reagents. The cationic species considered were Fe3+, Cu2+ and Ca2+, and the anions were CO? and S2 as these are normally present during the process of grinding of gold ores in the region. The organic surfactants examined were K-amyl- xanthate, dodecylamine-hydrochloride and the Grinding Aid XFS-4272 manufactured by Dow Chemical The study was primarily based on an examination of the electrokinetic properties of quartz surface in the presence of the grinding reagents. Zeta potential at different reagent additions and pH values in the presence of individual reagents were examined and the corresponding grinding charcteristics determined. A correlation has been indicated between the grinding characteristics, as measured by the -53um size fraction produced, and the surface energy of quartz. It was observed that an

Jan 1, 1978

By M M. Pande, M Ishfaq

The effect of aluminium on nitrogen solubility was investigated by equilibrating melt comprising master alloy of Fe-Al with pure electrolytic iron in a controlled atmosphere (pure argon) at 1873 K. Nitrogen in the samples was measured by sampling technique using inert gas fusion absorptiometry. It was found that nitrogen content decreases steadily with aluminium concentration and gradually, becomes close to 1 ppm for very high aluminium steels. Wagner’s second order interaction parameter formalism has been used to estimate the equilibrium constant and interaction parameters. Scanning electron microscopy (SEM) investigation showed, dual-phase inclusions comprising AlN phase surrounding alumina core. The 3D morphology of inclusions was studied by extracting the sample from the top and the central bottom portion of the solidified ingot. A sparse distribution of nitrogen was found for most of the inclusions which manifested the presence of almost pure alumina inclusions with different morphologies and sizes.

Jun 19, 2024

By G R. Ballantyne, V Souto, K Bartram

Particle sorting allows partially liberated minerals to be separated prior to energy intensive fine grinding. Sensors select particles for separation and air, water or mechanical ejectors are used to physically deflect those selected. To achieve effective separation there has to be sufficient liberation, accurate detection and presentation of a separated monolayer of particles. These three physical constraints determine the particle size limits, the sorting technology utilised, the separation efficiency, and the throughput that can be achieved. The combination of all these factors controls the effective limits on the degree to which sorting can reduce the specific comminution requirements and increasing energy efficiency. This paper will explore two case studies: the application of sorting in base metal mining and precious metal mining.CITATION:Ballantyne, G R, Hilden, M, Bartram, K and Souto, V, 2018. Characterising energy efficiency of particle sorting, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 531–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Blast furnace slags which fall into the quaternary system SiO2 - A1203 - MgO - CaO have latent hydraulic properties which depend on the degree of vitrification. When the oxides com- bine to form Calcium Silicate Hydrates and other products of hydration the bonds between elements are at a lower energy level than those which exist in the glassy state. Transition from the glassy state to the crystalline state is thermo- dynamically favoured and, in the context of this paper, such slags possess internal energy. Manufacture of Portland cement is respon- sible for about 3.6 per cent of total industrial energy consumption in Canada. Pyroprocessing accounts for about 83 per cent of this figure or 3 per cent of the total. The processing of blast furnace slag to a condition in which it can be used as a partial substitute for Portland cement requires no pyroprocessing and, on average, only about 11 per cent of the energy needed for Portland cement. In North America the benefits of slag as a cementitious materials have been obscured by other considerations, the most important being commercial strategy. This situation has under- gone radical change as a result of the rising cost of energy, and government pressures to conserve energy.

Jan 1, 1979

By R van Berkel, J Lay, D van Beers

The development of regional resource synergies in intensive areas with concentrations of minerals processing industries provides a significant avenue towards sustainable resource processing. Gladstone (Queensland) and Kwinana (Western Australia) are two of AustraliaÆs major heavy industrial areas. There are a number of successful regional synergies in both areas. In addition to the existing regional synergies in both areas, more potential synergy opportunities appear to exist which, upon implementation, could benefit industry, the environment and the community. To further enhance the development of such potential regional synergies, the Centre for Sustainable Resource Processing (http://www.csrp.com.au) commissioned research projects to facilitate the identification of potential synergies and assist with their implementation in both regions. This paper presents a selection of specific examples from both regions to illustrate the sustainability benefits from regional synergy developments. Although the composition of industries in the Gladstone and Kwinana regions is different both in terms of geography and industry diversity, similarities in synergy developments for both regions are apparent. Consequently, the examples discussed in this paper are organised around the key themes of water, energy and inorganic by-products. Comparison on a theme basis highlights success factors of successful synergies and demonstrates the range of benefits resulting from their implementation.

Jan 1, 2006

By P Kappen, R N. Collins, K M. Spiers

X-ray absorption spectroscopy (XAS) is a synchrotron-only technique used to determine chemical speciation, providing a powerful alternative to most traditional ‘wet chemistry’ and lab-based speciation methods. XAS is an element specific method that can be used to address a variety of systems, ranging from heterogeneous to homogeneous, polycrystalline to amorphous, and solid to liquid. The strength of XAS in identifying and managing chemical species in tailings and mine waste is demonstrated, with the presentation of highly relevant studies into lead, uranium, chromium and arsenic speciation. In each example, waste samples are compared with known standards, allowing an assessment to be made of the quantity of particular chemical species in each.CITATION:Spiers, K M, Collins, R N and Kappen, P, 2015. ‘Forget the wet chemistry’ – how the Australian Synchrotron can help with tailings and mine waste management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 145–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By F Shi, G Ballantyne, K Runge

There has been minimal innovation in the methods used to process an ore over the last 50 years. Productivity increases have largely resulted in increased equipment size without implementation of parallel improvements in technology. Complex orebodies of the future will need mining operations to adopt new technologies and techniques to make future ore treatment economically viable. Three emerging technologies, namely high voltage pulse (HVP) pretreatment, fine screening and the HydroFloat<sub>TM</sub> coarse particle flotation cell will be presented in this paper and the potential benefits that may result if they are adopted in mineral processing circuits will be outlined. The barriers that must be overcome before they can be adopted by industry with confidence will also be discussed. CITATION: Runge, K, Shi, F and Ballantyne, G, 2018. New technologies that will potentially enable processing of complex orebodies, in Proceedings Complex Orebodies Conference 2018, pp 126–129 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By K Dagdelen, I Traore

This paper presents an iterative net present value (NPV) maximisation method to determine the optimum surface to underground transition depth for an orebody to be mined by multiple open pits and an underground mine. The determination of transition depth from open pit to underground mining is based on global production scheduling optimisation of open pit and underground mines using mixed integer linear programming. The method is applied to a case study coming from a gold mining complex with six open pits and a large underground mine using longhole open stoping. The results indicate potential improvements of the NPV of global operations when compared to the traditional techniques based on independently optimised open pit first, followed by underground mining.CITATION:Dagdelen, K and Traore, I, 2014. Open pit transition depth determination through global analysis of open pit and underground mine production scheduling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 195–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Fermino R

Reduction of waste oxides from steel plant operations was investigated in a laboratory tube furnace at different temperatures and furnace atmospheres. The results have shown that the waste oxide pellets are reduced rapidly to very high degrees of metallization irrespective of the furnace atmosphere and that the reduction is simultaneously accompanied by significant low- ering of the original impurities. It is shown, for example, that treatment at 1000¦C for 30 min. can reduce the Zn content from 0.98% to 0.0065% and K and Na contents from 0.19% and 0.76% respectively, to less than 0.01%. However, pellet strength at 1000¦C was low but this, as shown in the paper, can be very significantly improved by treatment at 1250¦C. The results indicate that the reduction of the waste oxide pellets of this investigation proceeds almost certainly by a chain reaction mechanism and that this principle could be advantageously extended to the reduction of iron ores and other oxides in general.

Jan 1, 1984

By Nowell SB, Cottrill DA

Host-rock - wallrock major and trace element geochemistry associated with epithermal gold mineralisation in the Hauraki Goldfield of New Zealand is poorly documented, even though rock geochemistry is a recognised tool in exploration. Such responses assist in recognition of the regional scale imprint of fossil hydrothermal activity, and indicate targets for detailed evaluation within these alteration zones.Recent investigation of gold deposits in the Waihi (Gladstone), Golden Cross (Empire), Thames (Waiotahi) and Coromandel (Tokatea) areas indicate enrichments of Au, As and Sb in the andesitic wallrocks hosting mineralisation. Of the other elements examined, Si, K and Rb are enriched, and Na, Ca, and Sr are depleted at all deposits. These trends are best developed in the vicinity of veining. In deposits with clay alteration dominating (Waiotahi and Tokatea) there is also depletion of Mg, Mn, Zn and Cu. Ba and Cr are variably enriched or depleted within different styles of alteration. Base-metal enrichment in the wallrocks is not a feature of Hauraki deposits.

Jan 1, 1990

The geographical and geological situations of the two mineral sand deposits currently being mined by Western Titanium Limited and the mining methods in use are briefly described. Production scheduling involving the ability to vary the proportions of the major minerals produced, together with maintaining a constant feed grade to the wet concentrator has been assuming greater importance to the company in recent years as the relative value of these minerals, due mainly to technological advances and environmental considerations, is subject to significant and rapid change. Manual calculation, even using a programmable calculator, became a trade-off between man hours and data usage. Schedules were updated infrequently and only a fraction of the avail- able data was used. In July 1975 a Data General NOVA 2/10 minicomputer with a 24K word core and three cassette drives was purchased. A suite of programmes was developed using BASIC to assist in production scheduling and these were opera- tional early in 1976.

Jan 1, 1977

By Sudharto RT

Sulphides of Cu, Pb, and Zn occur in quartz veins associated with a quartz monzodiorite stock at Gunung Limbung, West Java. The mineralization was polyphase and occurred at depths of less than lkm. Wall- rock alteration is extensive and typically consists of an outer zone of propylitization and an inner zone of potassic (K-feldspar- rich) alteration. Sporadic argillic altera- tion is probably of supergene origin. A variety of elements were mobilised during hydrothermal alteration and Ba in particular shows mared enrichments in the potassic zone. Fluid inclusions in the vein quartz indicate that temperatures of mineralization were within the range 250-3900C and that two fluids with differing chemistry were involved. One fluid had high Ca/Na ratios and a low overall salinity, the other had low Ca/Na ratios and a moderate salinity. The former is probably of meteoric derivation, whilst the latter had a magmatic origin. Precipitation of the sulphides was probably brought about by mixing of these fluids.

Jan 1, 1987

By Li N, Grimsey E. J

A technique has been developed for the fast measurement of the liquidus temperature of molten salt systems. The method employs a type K thermocouple embedded within the centre of a copper cylinder. The cylinder is immersed into the molten salt bath and the resultant heating curve is recorded using a PC-based data logging system. Upon immersion of the cylinder into the bath, a layer of salt freezes from the melt onto the surface. When this layer remelts during heating, the shape of the heating curve exhibits a change. The onset of this change can be detected by numerical differentiation of the heating curve, and the temperature at the onset represents an estimate of the liquidus of the melt. This work describes the technique and its application to the measurement of liquidus temperatures of MgC12 - NaCl and BaC12 - NaCl salt mixtures, in addition to a number of solidus temperatures.

Jan 1, 1996

By G Lane, S Morrell

The design of the 12 m diameter SAG mill installed at the Cadia Hill Mine in New South Wales followed after two years of extensive laboratory and pilot plant testwork. The testwork showed the Cadia ores to be hard and competent necessitating the use of both a variable speed SAG mill drive and pebble crushing. The grinding power requirements for the SAG mill was based on engineering in-house grinding software, pilot plant data and simulations using JK SimMet software. Surveys of the SAG mill operation during the first four weeks showed the feed size distribution, transfer size and pebble rate to be lower or less than those for which it was designed. To compensate for the lower pebble rate, the SAG ball load was increased. This resulted in the total comminution circuit power being some 0.5 kWh/t higher than predicted. The JK SimMet SAG model has been modified to take account of these variations.

Jan 1, 2000

Ordovician metasedimenIs near the Karamea Bend and east of Ihe upper Carboniferous Karamea batholith were intruded by acidic stocks during the Cretaeeous. K/ Ar dating of two of the stocks gave 110 ± 3 millionyears whereas the batholith granite gave 290 8 ± million years. All but one of the stocks mapped lie on an approximately ENE line along which they show gradation in composition, texture, and alteration.Most of the intrusions have produced homfelsic haloes in the surrounding rocks but the hydrothermal alteration centred near the head of Questa Creek is quite distinct. Here much wider zones of alteration are characterised by chlorite, green biotite, sericite, and quartz-orthoclase in order towards the centre, though no stock crops out. Each zone of stronger alteration is heralded by "spots" containing the next characteristic mineral.It is suggested that a late phase of the intrusive period that gave rise to the outcropping stocks also gave rise to a volatile-rich intrusion still hidden beneath the head of Questa Creek.

Jan 1, 1976

The activiltion of sphalerite with electrolytically generated copper ions from a copper electrode instead of the usual practice of the addition of copper sulphate was studied in the laboratory. A large surface area of copper was provided by lining three sides of a bench flotation cell with copper sheeting. The lining was connected to the positive terminal of a low voltage d.c. source, and the cell impeller to the negative terminal.Sphalerite was effectively activated by this arrangement and was subsequently floated using xanthate as the collector.Flotation results comparable to those obtained with 1 lb/ton CuS04.5H20 (0,255 lb/ton copper) were obtained using 0·1062 lb/ton of electrolytic copper and 0·488 kWh of electrical energy. The wastage of copper due to the formation of insoluble precipitates was found to be dependent on the length of time the current was passed. Maximum current was passed for the shortest time to minimize wastage.

Jan 1, 1973

By G H. Park, Y J. Jun, J H. Park

The carbon solubility of the CaO-Al2O3-FeO-SiO2-MgO slag, the main system formed in the Ruhrstahl-Heraeus (RH) vacuum degasser, was measured at 1873 K to understand the effect of slag compositions on the carbon contamination in the ultra-low carbon (ULC) steels. The stable form of carbon was demonstrated to be carbonate by plotting the log [(wt%C)/aC] ratio against the log p(O2) which ranged -11 < log p(O2,atm) < -9. The carbon solubility of the CaO-Al2O3-FeO-SiO2-MgO slag can be estimated using thermodynamic model. The distribution ratio of carbon increased with increasing concentration of FeO due to the FeO reduction reaction and increased basicity of slag. The carbonate capacity of the CaO-Al2O3-FeO-SiO2-MgO slag can be expressed as a linear function of the activity of lime and the optical basicity.

Jun 19, 2024