Search Documents

By Geisler P, Sutherland P

The technical limits for high-pressure transport of large particle solids by means of sludge pumps, piston pumps or the like lead to the development of the pipe-feeder system. The pipe-feeder is a type of pressure lock in which the high-pressure pump itself is not in contact with the solids. Simultaneous operation of the three chambers with corresponding control of the valves allows continuous flow in both the primary and secondary circuits. Initially the pipe-feeder was used only for the transport of solids. Today it also operates with great success in central mine cooling systems, serving as an alternative for high-pressure/low-pressure heat exchangers or Pelton systems. In addition to the technology applied up to now, the pipe-feeder is also capable of transporting ice slurry, thus increasing cooling output consider- Ably.

Jan 1, 1991

Rockbursts, as they occur in South African deep level gold mines, have a lot in common with natural earthquakes. Both violently release seismic energy and cause damage to underground and surface structures. Rockbursts are the main cause of fatalities in deep gold mines and the problem may increase in severity with future mining at greater depths. Although the emphasis in Rock mechanics is on the prevention of rockbursts, prediction would provide a partial solution to the rockburst problem. A research project was initiated in 1981 on Western Deep Levels to investigate the possibility of detecting and identifying precursive microseismic activity. This project has succeeded in locating potential sources of seismic events with reasonable confidence. The timing of these events may be estimated with less confidence, and an important parameter, namely the potential size of the rockburst, still cannot be determined. An example of a large seismic event and its associated precursive activity are discussed. Practical prediction systems will, at least for some time, involve subjective decision making which will place a new responsibility on the mine manager as well as the rockburst specialist. The moral pressure on the manager as the final decision maker will probably be greater than the fear of leqal prosecution.

Jan 1, 1986

The combustion characteristics of Australian coals which contain high inertinite have been studied in a laboratory drop tube furnace and a Thermogravimetric Analyser. The pyrolysis chars and combustion residues were microscopically characterised using a modified coal petrography technique. Results indicated that the overall burnout of inertinite-rich Australian coals under pulverised fuel combustion conditions could be generally within a range of 97 - 99 per cent burnout. The studies showed that poor coal burnout cannot be generally related to high inertinite content in the Australian coals. The extent of coal burnout varies from coal to coal and vitrinite as well as inertinite may contribute to the unbumt chars in combustion residues. Combustion conditions had greater influence over char formation and coal burnout than the coal properties. However, under similar pf combustion conditions, coal rank and coal maceral composition had a strong influence over the coal combustion behaviours and final coal burnout. Simple correlations using coal properties may be used but with caution to determine coal volatile release and burnout at high temperature and rapid heating conditions.

Jan 1, 1991

By C X. Zhang, W K. Ru, S C. Hu

To study the creep properties and the energy evolution characteristics of the weakly cemented rock (WCR) in western China, the creep deformation damage law of weakly cemented mudstone (WCM) under graded loading and the energy evolution characteristics of each creep stage were analysed based on the triaxial graded loading creep test of WCR. The results showed that as the confining pressure increased, the creep failure strength of the WCM increased from 9.5 to 24.8 MPa, and the relative displacement of the mineral particles in the mudstone increased gradually, resulting in a reduction in the fracture angle from 79.7° to 58.3°. At the same stress level, the strain energy Ue, the total energy U, and the dissipation energy Ud all increased as the confining pressure increased, but the growth rates of U and Ud decreased gradually, while the growth rate of Ue remained high. At the end of the stable creep stage, Ue increased slowly with the confining pressure, while U and Ud increased rapidly with the confining pressure, and their growth rates were basically the same. At the end of the accelerated creep stage, the growth trends of these three energies were all positively correlated with the confining pressure, Ue was significantly lower than that at the end of the stable creep stage, and Ud and U were further increased. These results revealed the unique creep properties and energy evolution characteristics of the WCR, providing a theoretical basis for long-term stability control of roadways that are built with WCR.

Nov 29, 2022

By H M. Parker, G Verly, T Postolski

Assessing the uncertainty and risk in mineral resource estimation is required for best practice and is implied by the public reporting codes in the categorisation of mineral resources and reserves. One industry best practice is quantifying the risk on future production for a given period, which can be done using two geostatistical approaches: conditional simulation and drill hole spacing studies based on estimation variances. Conditional simulation can provide a more complete and flexible answer to the problem, but it takes a fair amount of time to complete. Drill hole spacing studies are simpler, faster and can provide reasonable assessments of mineral resource uncertainty.This paper is a presentation of the principles, theory and practice of drill hole spacing studies. Various types of risk assessment are considered. Difficulties encountered in practice are discussed, and solutions are proposed. The important parameters impacting the results are reviewed. Examples of results and sensitivities are shown.CITATION:Verly, G, Postolski, T and Parker, H M, 2014. Assessing uncertainty with drill hole spacing studies – applications to mineral resources, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 109–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

This paper describes the development of an approach to sustainable development for application at the feasibility study stage for a proposed bauxite mine near the community of Aurukun, south of Weipa on the western coast of Cape York Peninsula, Queensland, Australia. The general environment for development was complex in all dimensions. In particular, the socio-demographic profile of the Aurukun community (population 1200) characterised it as being amongst the most disadvantaged communities in Australia. The traditional owners of the area, the Wik and Wik-Way people, were at the forefront in the efforts of Indigenous people in Australia to secure land rights over the past 30 years, and they had previous experience negotiating an Indigenous Land Use Agreement (the Western Cape Communities Coexistence Agreement) with Rio Tinto Alcan, the operators of the Weipa bauxite mine. Through this they had shown a well-founded sense of entitlement with respect to the development of resources on their traditional land. The Queensland State Government had recently cancelled an existing mining lease over the bauxite resource as the holder of the tenement had not fulfilled the terms of a development agreement that had been in place for 30 years. The Government was anxious to avoid any future æbankingÆ of the resource, and had decided to offer tenure to the resource on an international competitive basis, subject to the requirements of the Commonwealth Native Title Act 1993. This would require a negotiation process with traditional owners and potentially involve companies with whom the traditional owners had no existing relationship (typically developed during the projectÆs exploration phase) and who possibly had no project development experience in Australia. As well, the State Government envisaged an approach to development that drew on the significant work that industry and other stakeholders had undertaken over the previous ten to 15 years, commencing with the mining, minerals and sustainable development (MMSD) process. This work was aimed at rectifying acknowledged deficiencies with industry recognition of stakeholder interests, in particular with respect to environmental management and socioeconomic development. The approach adopted aimed to define the strategic community interests and sustainable development outcomes to which the development of the resource would be expected to contribute, and to embody these within an easily usable management structure that could be applied to each stage of project development from feasibility study through to mine closure. The logical framework (AusAID, 2006; ICMM, 2005) was the management tool utilised to order the identified interests and desired outcomes. The structure included components aligned with the key areas of development interest expressed by the community, and the initial baseline sustainable development plan (SDP) developed established component objectives, outcomes, indicative outputs and activities for the feasibility stage of the project. This established an objective framework to guide potential bidders when developing their response to the State GovernmentÆs Request for Proposal. The paper will describe the evolution of the competitive process and the parallel process for development of the SDP. While the institutional environment was politically and socially complex, the use of simple visual representations of the environment and the analysis and ordering of issues, objectives and criteria through methods such as stakeholder analysis and the logical framework approach, enable the development of a dialogue on the contribution that the development of a mining project can make to sustainable community development, and for the development of an agreed program of community support to capture the contribution. The use of the logical framework was found to have good functionality for plan development. Achieving plan outcomes though, is highly dependent on the skill of key project personnel in facilitation, team building, conflict resolution and leadership, as well as their ability to influence the behaviour of key stakeholders with the capacity and authority to require the integration of local economic development criteria in to key project development decisions.

Jan 1, 2009

By N Guresin, M Rohde

A lead-zinc flotation tailings sample containing silver from BHP Billiton’s Cannington Mine has been characterised to understand occurrences of silver in the tailings by conventional elemental, X-ray diffraction (XRD) and size analyses followed by mineralogical analysis with a scanning electron microscope (SEM) equipped with mineral liberation analysis (MLA) software and the use of an adapted diagnostic leach process originally developed for gold containing materials.The tailings sample contained 67 g/t Ag, 1.8 per cent Pb and 0.52 per cent Zn. The XRD analysis showed that the sample consisted of 74 per cent silicates, nine per cent sulfides, 11 per cent magnetite and small amounts of other minerals such as fluorite, fluorapatite and rutile. The p80 and p50 of the sample were determined to be 106 µm and 38 µm, respectively. The silver distribution was high in the small size fraction with 52.1 per cent of the silver being in the -8 µm fraction. The silver minerals freibergite, acanthite, jamesonite, pyrargyrite and native silver were observed in the mineralogical analysis of the sample by SEM/MLA. The associations of the minerals were intricate and the occurrences of silver were complex. There were finely disseminated silver minerals and also coarser grains of silver minerals in composites with the host minerals. It was estimated that almost 50 per cent of the silver was contained in pyrargyrite, around 14 per cent as native silver and contained in acanthite, 12.5 per cent in galena and around ten per cent in freibergite and jamesonite.These composite particles and the type of the silver minerals present were expected to limit leaching efficiencies of the silver in hydrometallurgical processing. The diagnostic leach tests showed that around 50 per cent of the silver could be recovered by direct cyanidation and higher extractions could be achieved by more aggressive acidic systems.Cyanidation tests were conducted to confirm the findings of the diagnostic leach studies. The investigated cyanidation parameters were time (up to 48 hours), solid to liquid ratio (1:1 and 1:2), cyanide concentration (0.025 M, 0.5 M and 0.1 M) and particle size (p80 of 106 µm, 63 µm and 7.5 µm). The effects of oxygen and lead nitrate were also studied. The tests were conducted at atmospheric temperatures. The maximum silver recovery obtained was about 50 per cent for all the parameter ranges trialled except particle size. The decrease in particle size from 106 µm to 7.5 µm by fine grinding resulted in an increase in silver recoveries from 50 per cent up to approximately 82 per cent indicating that the liberation of the silver grains/minerals is one of the factors affecting the cyanidation recovery of silver in addition to the presence of refractory silver minerals not amenable to cyanidation.Low head grades of silver in the tailings and relatively low cyanidation recoveries of silver (without fine grinding) necessitate a thorough cost analysis for the cyanidation of the Cannington lead and zinc tailings to assess if cyanidation would be a suitable process option for the extraction of silver. It is clear that one of the most important factors in determining the cost feasibility will be the price of silver in the world metal market.CITATION:Rohde, M, Guresin, N and Johnson, N W, 2014. Characterisation of silver minerals in lead-zinc flotation tailings and their response to cyanidation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 163–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Semple DG, Leach TM

A continued exploration programme has further defined the geology of the Tolukuma vein system, verified the resource indicated by Newmont, and identified potential for additional mineralisation. The resource at Tolukuma Hill, designated as Zone C, is a measured 440,000t @ 17g/t Au and 46g/t Ag with an additional indicated resource of 120,000t @ 16g/t Au. A diatreme breccia localised at an intersection of structures, and a relationship of gold to base metal sulphides, are highly indicative of a porphyry association. Typical epi-thermal features such as crustiform banded quartz and quartz pseudomorphing. platy calcite are also present and locally contain lesser gold mineral-isation. Pre-existing dilatant structures have acted as a host to the ore fluids, resulting in the formation of the semi-continuous Tolukuma-Gulbadi veins over a 1100m strike. A fluid flow model suggests that mineralising fluids were sourced from the diatreme margins and migrated laterally along dilatant structures. Bonanza gold grades are derived through fluid quenching in the flexure between a hanging wall split which hosts much of the Tolukuma Hill resource and the feeder graben structure. Thus, the relationship between the pre-mineral structural geometry and fluid upflow at the margins of a diatreme breccia, controls the ore setting. Potential for more ore remains within the Gufinis and the 120 veins as well as in the outlying Prospects.

Jan 1, 1994

By B Crompton, A Berghorst, G Knox

Laboratory-based dynamic testing provides an invaluable tool in the development of rock bolts for use in highly stressed, burst prone rock masses. While in most cases the laboratory-based test method is not a direct comparison to an in-situ installation due to the purely axial loading and variations in boundary conditions, it does provide an indication of the performance of the tendon system under dynamic loading. The aim of the research described in this paper is to provide an understanding of the effect of the impact velocity of the impact mass during a laboratory-based dynamic test. Understanding the effect of boundary conditions of laboratory testing will improve Geotechnical Engineers understanding of the performance in an in-situ installation. In addition, due to the limited number of dynamic test facilities, an understanding of the effects of the boundary conditions will aid in the comparison of test results for different products from different test facilities. The research was conducted using an impact tester, whereby a known mass is raised to a known height defining the kinetic energy and velocity of the mass at the point of impact with the test sample after release. The impact velocity was varied between 2.7 m/s and 5.4 m/s, while the kinetic energy of the mass was maintained at 11.5 kJ. While a correlation between the impact velocity and strain rate of the system tested was established, due to the properties of the system tested, the range of impact velocity on which dynamic tests were conducted was insufficient to result in a considerable change in the average impact load, the cumulative proximal displacement and the cumulative maximum energy absorbed over multiple impulse. However, due to the reduction in the momentum of the impact mass the impact duration and displacement during each impulse in the series of impulses reduced. CITATION:Knox, G, Berghorst, A and Crompton, B, 2018. The relationship between the magnitude of impact velocity per impulse and cumulative absorbed energy capacity of a rock bolt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 160–169 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By S Robinson, A Turner, R Dale, C Butler

"Sandfire Resources NL- (‘Sandfire’) DeGrussa definitive feasibility study (DFS) identified geometallurgy as a major factor in achieving optimum plant performance at the DeGrussa mine. A geometallurgical initiative was created to proactively investigate this issue, and a key initial achievement was the 2013 paper by Condon et al (2013) on developing a working geometallurgical model from first principles. Significant advancements in Sandfire’s geometallurgical understanding since that publication now shape how information is presented and communicated.The main geometallurgical parameters so far identified as critical factors affecting plant performance are Cu:S ratio, iron sulfide mineralogy, talc carbonate content and sphalerite content. Apart from specific mill strategies, geometallurgical issues have been managed through communication between departments and strategic run-of-mine (ROM) pad management.This paper uses the current theories of geological evolution of the volcanogenic massive sulfide (VMS) deposit at DeGrussa, to discuss the variability between the orebodies C1, DeGrussa (sea floor mounds) and C4, C5 (sub-sea floor replacement) to highlight the different issues each orebody is expected to encounter when processing.A zone of altered low-grade mineralisation surrounds the main orebodies at DeGrussa, referred to as a halo. Talc minerals are often patchy within this halo and often cause significant recovery issues during processing. This halo has been successfully modelled using MgO as a proxy. The ability to model the talc material assists with both identifying potentially problematic zones for processing and geological interpretation of the ore deposits evolution.Early in geometallurgy studies at DeGrussa it became apparent that it would be useful to identify processing performance prior to mining. This necessitated the incorporation of specific sulfide species into the mining block model. These attributes are interpolated from the logged sulfide estimates allowing a clear picture of the abundance of each mineral type within a defined area.In conjunction with the block model a geometallurgical factor (GMF) graph was developed, identifying sulfide mineralogy based upon mineral assays. These two recent additions to the model provide a clear picture of the nature of the ore sources that will be presented to the processing plant.The future of geometallurgy at DeGrussa will see these tools used to aid mine scheduling with a view to further improve processing recoveries.CITATION:Butler, C, Dale, R, Robinson, S and Turner, A, 2016. Geometallurgy – Bridging the Gap between Mine and Mill: a Case Study of the DeGrussa Geometallurgy Program, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The initially cautious approach taken towards ground support and reinforcement at the Porgera Underground Gold Mine in the Highlands of Papua New Guinea has evolved rapidly in the two years since stoping commenced. The confidence to continue the evolution process has grown from an increasing knowledge of mining conditions as stoping has progressed, to the extent that reinforcement requirements have decreased by 50 to 75 per cent depending on local circumstances. Changes to mining practices have significantly assisted and influenced this process.Empirical observations of ground behaviour, assisted by a deliberately selective extensometer monitoring program, provided the stimulus for early changes to ground support and reinforcement practices. Further optimisation of the ground support and reinforcement effort is being pursued through an active monitoring, measuring and analysis program. Ultimately, situation rather than site specific design will ensure continuing high quality ground support and reinforcement installations. However, local structural and lithological factors will continue to become more critical as the optimum position is reached.

Jan 1, 1993

By Storey AG

Following initial plant scale work on the development and performance of 'spray' oil lances, a full scale room temperature model of the blowpipe-tuyere region of a blast furnace was built to study the basic aerodynamic features of auxiliary fuel injection procedures. Mobilwax 2305 was used as a substitute for Bunker C oil fuel in view of its similar physical properties and the fact that the atomised droplets could be frozen in flight and size, distribution analyses made for various operating procedures. It was shown that secondary atomisation processes far outweighed the importance of any primary atomisation procedures in determining mean Sauter Diameters particularly at high windrates typical of current blast furnace technology. It was also found that good spray dispersions across the blow pipe could only be obtaind for liquid fuels and that the lateral rate of spray dispersion was substantially enhanced by primary atomisation procedures. Mean particle diameters of sprays were found to be predictable on the basis of elementary stability theory and fell within the size range necessary for good combustion at all liquid fuel rates studied. The possible effects of high oil injection rates on flooding phenomena in the furnace bosh were considered. Comparisons show that high oil rates can lead to significant increases in the hanging factor (e.g. 'V 10% at 135 kg oil/thm) owing to increased gas flow rates/thm resulting from the presence of hydrogen.

Jan 1, 1975

By D J. Williams, A Shokouhi, A Naderian

Extracting alumina from bauxite involves the production of fine-grained waste known as red mud. The highly alkaline red mud is usually neutralised by applying sea water, thickened to between 25% and 30% solids by mass, before disposal to a Tailing Storage Facility (TSF). Hydraulic sorting, settling, self-weight consolidation, and desiccation are the processes contributing to the overall volume change of the red mud after deposition. Investigating the effect of these processes on the volume change behaviour of the fine-grained red mud is an important step in the estimation of the required storage volume of the storage facilities. This paper presents the results of a series of laboratory consolidation tests in a slurry consolidometer, and comparisons are made with field testing and observations.CITATION:Shokouhi, A, Naderian, A and Williams, D J, 2018. Assessing the volume change behaviour of red mud through laboratory and field testing, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 309–316 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By K Watters

API Management Pty Ltd (API) is currently developing the West Pilbara Iron Project (the ‘Project’). The Project is a substantial greenfi elds mining and infrastructure development proposed for the west Pilbara region of Western Australia. The Project will establish API as a new and independent supplier of direct shipped iron ore. API manages the Australian Premium Iron Joint Venture (APIJV) on behalf of joint venture participants Aquila Resources Ltd and American Metals and Coal International Inc. The APIJV was formed in February 2005 with the objective of developing a long-term iron ore export operation in the west Pilbara region.Development of Stage 1 comprises a 30 million tonne per annum (Mt/a) channel iron deposit (CID) operation scheduled to commence in the second half of 2014 subject to approvals. JORC compliant CID resources total nearly 700 million tonnes and the Stage 1 mining area comprises eight iron ore deposits located between 30 km and 85 km south of Pannawonica. Run-of-mine ore from the eight deposits is transported to a central processing facility for crushing, screening and blending into a sinter fines product, which API has named West Pilbara Fines or WPF. Construction of a 282 km main line heavy haulage railway from the Stage 1 mining area to the proposed greenfields multi-user port at Anketell Point near Wickham, is capable of accommodating large Capesize bulk carriers and providing export facilities for other third parties. Capital investment in the order of $A6 billion includes essential support infrastructure including power, water, accommodation, roads and an airport at the mine.A feasibility study for the development of the Stage 1 mine, rail and port infrastructure has been completed along with environmental surveys of the mine, rail and port areas with Public Environmental Reviews (PERs) for each submitted for public review by end 2010. Consultation and cooperation with various stakeholders of the Project areas, and early engagement with traditional owners of the respective areas has commenced. Various sampling and metallurgical characterisation programs combined with independent institute and steel mill based testing have confirmed the positive sintering characteristics of WPF ore, which is higher in alumina (3.37 per cent) than typical Pilbara ores. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

By R Dimitrakopoulos, C Paduraru

The optimisation of mine complexes and related value chains is a challenging problem due to the simultaneous presence of a highly-dimensional decision space, integer decision variables, non-linear constraints and recovery functions, as well as geological and market uncertainty. In addition, if the uncertainty is revealed progressively, then decisions need to continuously adapt to new information, which poses additional challenges. Stochastic dynamic programming is a well-known class of methods for addressing problems where a decision-maker reacts to new information. While simplistic applications of dynamic programming using exact representations would be intractable for any realistic mine planning problem, new dynamic programming methods using approximate value function representations have been successfully implemented in the past to address problems of similar complexity. This work formulates the problem of mine complex optimisation as an approximate dynamic program and presents an application of the resulting method to a gold-copper deposit.CITATION:Paduraru, C and Dimitrakopoulos, R, 2014. Mineral supply chain optimisation under uncertainty using approximate dynamic programming, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 415–422 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J Karlovšek

Civil engineering infrastructures are often subjected to different types of natural and mechanical activities. These influences may result in serviceability or even in stability of structures due to material deformations, increased water content within the materials used or the formation of internal or adjacent cavities that may threaten the infrastructure. Construction practices can lead to development of such defects in the form of cavities. In civil engineering it is crucial to detect these variations in material properties and to detect the presence of defects. However, as they are often hidden from view, these attributes may be difficult or impossible to target with traditional testing methods. For these reasons rapid geophysical methods, such as ground penetrating radar (GPR), are increasingly being used. At the University of Queensland (UQ) GPR is used for detection of voids and cavities which have been caused by an over excavation of the earth pressure balance machine (EPB) operating in a closed mode.A variety of numerical simulations using the finite-difference time-domain (FDTD) methods and preliminary experiments have been carried out in order to specify information about the nature, type, size, location and other characteristics of targets to be detected by GPR. In doing this the difficulty of interpreting GPR data, which is mainly due to the complexity of the factors involved in multiple possible solutions of the observed features, can be overcome.

Mar 8, 2011

By J Liu

In situ coal gasification is a method of extracting a high proportion of the energy value from coal without the need for mining. In situ conversion of coal to combustible gases is achieved by drilling wells into the seam, injecting gasification agents and initiating combustion. The product gases are then extracted to surface using production wells. These gases are clean energy sources for power generation, heating or synthetic fuel production. In situ coal gasification is of particular interest with respect to its lower environmental impact, potential application to otherwise inaccessible energy resources (ie offshore, deep deposits or beneath protected lands) and low capital intensity. Practical application of this clean technology is restricted primarily by lack of satisfactory quantitative descriptions of the processes involved, in particular the hydromechanical processes.In this study, three characteristic physical zones of an in situ gasifier are identified as the rubble zone, combustion front and virgin coal zone. Coupled mechanical processes of coal consumption and overburden collapse are used to describe the permeability profile in the rubble zone. Additionally, the redistribution of overburden load associated with coal consumption is accounted for with the formulation of a stress (compressive) dependent permeability profile, which is applied to the virgin coal zone. The model was implemented into and solved by FEMLAB, an advanced computer simulation tool. The flow process, according to DarcyÆs Law, is subsequently described in terms of permeability dependent injectivity. Injectivity is an indicator of flow velocity, which has been identified as a crucial factor in determining the commercial value of product gases from in situ coal gasification. The stress alteration to coal permeability was found to have a dominating influence on the flow process. This finding implies that a greater understanding of the in situ coal burning induced deformation of surrounding rocks would be of significant value in assessing the economic viability of applying this clean technology to potential sites.

Jan 1, 2004

By A G. Guinea

Every person in an organisation has what could be called ‘a different take’ on what it means to be a safety leader. The directors will tell you they are ultimately responsible for everyone’s safety and that they can be imprisoned as a consequence of a workplace fatality. Managers, take more of a focused approach and would explain that they are totally responsible for the safety of their teams. And then there are front-line leaders. Those that not only have the responsibility (like directors and managers) but they also have the accountability, and the ability, to influence how safely their teams work. But it is not just physical safety that leaders should be concerned with.

May 5, 2022

By P J. Willems, B J. Junor

Blackwater Mine is in the central-southern Bowen Basin, immediately south of the township of Blackwater on the Capricorn Highway. The current open cut operation extracts coal from three main seams, designated Top, Middle and Lower, in the Late Permian Rangal Coal Measures cropping out on the eastern flank of the Comet Ridge. Complex geological structures, dominated by E-W normal faults and N-S reverse faults, have significant detrimental effects on coal mining operations. Historical exploration before 2010 involved several types of drilling only to understand structure, coal quality and washability. Hence, although drilling data was combined with limited pit mapping and observation, unknown structures were still often encountered during excavations and led to mining surprises. In 2010 BHP completed 200-line km of closely spaced 2D seismic survey to capture gross and detailed structures followed by fit for purpose structural drilling to confirm major structures in the northern part of the mine. In 2018 a high density 9.2 km2 3D seismic survey was completed in the southern part of the mine. Subsequently, a 17.2 km2 survey was completed in 2020 to cover the northern active mining area. It allowed geoscientists to successfully map previously unknown major faults and seam splits, which could potentially impact the mineability of the area. It is important to note, that faults interpreted using modern high-density 3D data can be interpreted with dramatically higher confidence in the fault dip and azimuth orientation in comparison to the legacy 2D data. Along with targeted drilling, pit mapping and structural interpretation, the outcome adds value to mine planning and operations. This paper outlines recent successful seismic 3D data acquisition and interpretation. In detail, the paper presents case studies on how the data can be incorporated into a structural model to improve geological knowledge, enable geotechnical assessment, and support safe and efficient coal mining in a large and structurally complex mine.

Mar 22, 2022

By A D. Campbell

The Homer Tunnel is located in a remote area of the South Island of New Zealand and carries large numbers of tourists to Milford Sound through an avalanche prone area. The tunnel is 1280 m long with a steep ten per cent unidirectional grade descending to the west. Construction of the tunnel began in the 1930s and was completed to a nominal 6 m width in 1954. In 1996, two passing bays were stripped-out to accommodate bi-directional flow of tourist coaches. During all phases of construction and widening there have been episodes of strain bursting.The condition of the tunnel and standard of internal services is below current international practice, principally in terms of; in-tunnel air quality, fire life safety, ground support, and road safety. A number of near-miss events have occurred involving coach fires on the approaches and inside the tunnel. The national road authority, NZTA, is considering a substantial investment to improve amenity and safety of the tunnel.This paper describes the rationale for the proposed upgrade works and the investigations undertaken to enable that design. A holistic approach to road tunnel safety has been adopted that balances the key interrelated safety drivers, namely; tunnel lining, traffic operations, ventilation, power supply and egress while ensuring continuity of safe access to Milford Sound.

Mar 8, 2011