Search Documents

By T Takayama, M Matsumura, Y Konno

The steel industry accounts for 14 per cent of domestic CO2 emission in Japan, and iron ore sintering process occupies approximately three per cent. While Fe content in iron ore is gradually decreasing. So, the amount of concentrated iron ore will increase in the future. We have focused on magnetite concentrate as sinter materials, because magnetite can be easily magnetically beneficiated. However, it is experienced that blending magnetite ore resulted in increasing Fe2+ component in the iron ore sinter, which results in lower reducibility. Therefore, promoting the oxidation reaction from magnetite to hematite in the sintering process is countermeasure for reducibility. In addition, this promotion causes increase of oxidation heat, which results in high sinter strength and reduction of coke. It is assumed that the oxidation of magnetite tends to proceed in the cooling stage, where the oxygen partial pressure increases after the combustion of fine coke, but there are few studies on the effect of heat profile, especially cooling path. The purpose of this study is to design the effective sintering heat profile to promote oxidation of magnetite ore, especially, to investigate the effect of cooling path on sintered ore microstructure. In this study, magnetite ore and magnetite reagent were respectively mixed with calcium carbonate reagent. Then the mixed samples were pressed and formed into cylindrical tablets for simulating the adhesive layer of a pseudo particle. Through examining influence of maximum temperature and cooking rate on oxidation reaction of magnetite, we confirmed that the oxidation reaction of magnetite is suppressed at above 1350°C for maximum temperature, compared to 1300°C. Sintering at lower temperature is desirable because hematite is stable below 1350°C in the Fe2O3-CaO phase diagram.

Nov 8, 2021

By D R Van Eck

Western Deep Levels, a seismically active deep level told mine. stalled placing backfill in their narrow tabular workings as part of the regional support strategy in 1986. Over the years the percentage of working places being backfilled has been gradually increasing. At the end of 1995 the support efficiency and the labour productiveness relating to support installation were scrutinised to determine if resources were being optimised. Owing to financial, safety and productivity constraints it was decided to redesign stope support to be less labour intensive, safer and provide an integrated stope support system. This new integrated system will thus combine the previously used temporary, permanent and back area support consisting of mechanical props, hydraulic props and backfill respectively. Backfill previously formed an integral part of the regional support in conjunction with strike stabilising pillars. To design the integrated support system the backfill placement quality has to be exceptionally good and placement must be done as close as possible to the working face. The backfill to face distance was reduced by 30 per cent and in some areas by more than 50 per cent with an increase of square metres filled to increase the effect of the backfill even more. This paper addresses the design and successful implementation of an integrated stope support system based on the optimisation of backfill to he extent where installation of mechanical and hydraulic jacks could he Eliminated

Jan 1, 1998

By P Marianelli, J Theiler, B Beamish, A Spillman

The presence of reactive pyrite in waste rock contributes to the hazard of spontaneous combustion in emplacement facilities as it acts as an initiator of self-heating at low ambient temperatures. Organic carbon also present in the waste rocks acts as a fuel at elevated temperatures above 120°C and can lead to thermal runaway resulting in eventual ignition. A new laboratory test method (adiabatic incubation testing) is now available that can identify the presence of reactive pyrite and quantify the self-heating behaviour of the waste rock. McArthur River Mine has a waste rock profile that contains pyritic shale units, which have created spontaneous combustion events in the past. A systematic sampling and testing program is underway to characterise the spontaneous combustion hazard likelihood of the McArthur River Mine waste rocks to provide a sound database for future mine planning of the waste removal and emplacement. This paper presents some initial outcomes of this program and shows the leading practice in spontaneous combustion hazard assessment and management that has been adopted at McArthur River.CITATION:Beamish, B, Marianelli, P, Theiler, J and Spillman, A, 2018. Spontaneous combustion hazard assessment of McArthur River Mine waste rock, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 422–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By B P. Banerjee, S Raval

In the recent past there have been dramatic advancements in the development of remote sensing platforms (satellite, aircraft and unmanned aerial vehicles – UAVs) as well as sensor systems (multispectral, hyperspectral, thermal, light detection and ranging (LiDAR) and radar). However, selection of the appropriate remote sensing technique for a mining application is complex and requires scrutiny on multiple scales including spatial, temporal and imaging capabilities. This presentation highlights various conventional and emerging remote sensing approaches over a mine’s life.CITATION:Banerjee, B P and Raval, S, 2016. Applications of advanced remote sensing systems during a mine life, in Proceedings Life-of-Mine 2016 Conference , pp 116–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By P M. Cepuritis

In hard rock mining, large-scale bulk mining methods such as block or panel caving (BC/PC) and sublevel caving (SLC) typically generate significant surface deformations such as subsidence. Surface deformations need to be considered in the project evaluation and planning stages of cave mines, for example, planning and location of critical underground mine planning infrastructure such as portals, haulage and vent shafts, access roads, or potential damage to existing infrastructure, changes to surface water management, waste dump, stockpile and tailings dam stability, and environmental impacts. Assessing the impact and risks associated with subsidence is a key component in robust mine planning and operations management.

Nov 29, 2022

By J G. Shellnutt, Y Iizuka, T W-Y Hsia, T-C Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of magmatic oxide ore deposits hosted in chemically-evolved layered gabbroic intrusions is attributed to a variety of petrological processes, but there is little to no consensus on the general applicability of each model. Complicating the matter further is that many layered gabbroic intrusions are spatially and temporally associated with alkaline A-type granites, suggesting that there is a petrogenetic relationship between the two types of chemically different rocks. Our experimental results show that petrological modelling using a starting composition of high-Ti basalt from the Emeishan large igneous province can produce evolved silicic liquids that resemble the compositions of microgranular enclaves from the syenitic unit of the bimodal, oxide ore-bearing Baima igneous complex. The experimental results confirm that bimodal gabbro-granitoid complexes can form from a common parental magma and that early crystallisation of Ti-rich magnetite can explain the formation of the oxide ore deposits in the lower parts of the layered gabbroic intrusions. We conclude that crystallisation of a typical high-Ti basaltic parental magma can produce world-class giant magmatic oxide ore deposits and that the occurrence of some alkaline granites may be an indicator of their presence.CITATION:Shellnutt, J G, Hsia, T W-Y, Liu, T-C and Iizuka, Y, 2015. Cogenetic formation of the peralkaline syenite and oxide ore-bearing layered gabbroic intrusion of the Baima igneous complex, Emeishan large igneous province, south-west China , in Proceedings PACRIM 2015 Congress, pp 317–324 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By S Mitra, T Singh, D O’Dea, T Honeyands

Permeability and air flow rate in the bed during iron ore sintering is crucial to controlling the sinter quality and productivity of a sinter plant due to its influence on the flame front speed. In the present work, the permeability of the bed during sintering was analysed by means of measured pressure drop and temperature at multiple points in the bed during sintering. Three different zones were categorised, ie humidified (green) bed, region of maximum resistance (high temperature zone) based on temperature, and sintered bed. Previous work has shown that the maximum pressure drop during sintering was due to several concurrent physico-chemical processes including dehumidification, calcination of fluxes, dehydroxylation of goethite, combustion of coke and melting of granules (>1200°C). To quantify the effect of the different process, sintering experiments were conducted in a milli-pot (diameter 53 mm, height 400 mm) with pressure and temperature measured at same location in bed. The milli-pot was fitted with four equidistant (80 mm apart) taps. Overall, five sections in the milli-pot were analysed for pressure drop at different times during sintering. It was found that in region of maximum resistance, coke combustion and flux calcination were highest contributors with ~35 per cent of the pressure drop when compared to other processes like de-humidification and goethite dehydroxylation which contributed to ~20 per cent and 25 per cent each respectively. The pressure drop contribution of the coke combustion region increased with increasing coke addition rate.

Nov 8, 2021

By Lawson F

Chrome chemicals are commercially produced by the alkali roasting of chromite ores with sodium carbonate. Results of tests conducted in a laboratory furnace indicated that the sodium carbonate reacted rapidly with part of the gangue material to form a metastable intermediate that later reacted further with the chromite. For the conditions used, the recovery of water-soluble sodium chromate was able to be described empirically as yield % = a tn with a = 0.24 T - 241.3; n = 3.90 - 3.12 × 10-3 T and t is the reaction time in hours.The major rate limiting step in the overall reaction sequence appears to be the rate at which oxygen can get to the reaction sites across the liquid film coating the solid reactants.Sodium sulfate alone was found to be an unsatisfactory source of alkali for reaction with chromite. However when limestone also was added in quantities sufficient to allow the reaction CaCO3 + Na2SO4 + H20 ? Ca SO4 + 2NaOH + CO2 to take place, the results obtained were comparable to those found when sodium car-bonate was used.For chromite particles in the size range -124 + 105 µm, the use of stoichiometric excess of sodium carbonate did not appear to increase the yield or the reaction rate significantly. However, with smaller sized particles, - 53 µm, increased yields of water-soluble chromate were obtained when roasted with more than the theoretical quantity of sodium carbonate.

Jan 1, 1984

In the last several years we have seen the demise of the Department of Mining and Metallurgy at the University of Melbourne, the removal of extraction metallurgy from the Department of Metallurgy and incorporation of it within a School of Mines at the University of New South Wales, and the joining of a small Department of Metallurgy with a Department of Chemical Engineering to form a Department of Chemical and Materials Engineering at the University of Newcastle. Most of these changes have been forced by the logical application of the principles of accounting, the currency for such accounting being the Whole Student Unit (WSU). It is not my intent to address the problem of attracting young people into courses in metallurgy (including extraction metallurgy) which, at present, is the only way to introduce black ink into the WSU accounting ledger. Rather, I wish to express my disquiet over the trends, illustrated by some of the above occurrences, of separating out extractive metallurgy from METALLURGY by suggesting in broad terms how a course in metallurgy should be structured. I firmly believe that the mechanical metallurgist and materials engineer need an exposure to chemical and extractive metallurgy; similarly, the extractive and process metallurgist should, in my view, have a good grounding in the interrelationships between composition, structure, and properties, this topic being the core of the basic subject physical metallurgy.

Jan 1, 1987

By J Lainé, M Badawi, A C. de Araujo, Y Foucaud, C Veloso

Flotation is the one of the most used techniques for the mineral separation of non-ferrous ores worldwide. However, the increase of the complexness along with the decrease of ores liberation sizes ought to become important challenges for mineral processing, including flotation. It now appears necessary to better understand the fundamentals of the flotation process, particularly the adsorption of flotation reagents at the liquid/mineral interfaces, to propose further improvements. Flotation relies on different phenomena: surfactants adsorption, on one hand, and collision, adhesion, and transport of particles with bubbles, on the other hand. For acknowledging the reagents adsorption mechanisms, molecular modelling tools borrowed from chemical and material sciences, are increasingly used. Atomistic simulations were successfully applied to study the flotation reagents interaction with various mineral surfaces, eg of two common minerals from iron ores, kaolinite, and magnetite surfaces, or with fluorite surface, a tungsten ores common gangue mineral.

Aug 24, 2022

By A S. Derrington

This paper describes a hybrid ventilation system, which uses secondary fans that also act as de-facto primary fans to extract fresh airflow from the mine intake raise system. Also discussed are the associated problems such as uncontrolled recirculation, inadequate decline airflow, fire safety issues, prolonged blast fume clearance times, high air temperatures in main access routes, neutralisation of mine air cooling by heat from secondary distribution fans, increased ventilation system complexity, reduced flexibility and high pressure differentials (which cause safety issues with personnel access and reduce secondary ventilation system performance).Practical suggestions are provided on options to avoid these problems listed.CITATION:Derrington, A S, 2013. A critique of the push-pull hybrid ventilation system, in Proceedings The Australian Mine Ventilation Conference , pp 73-78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By J Yamatomi, Y Tamanishi, S Miwa

The four-dimensional (4D) network relaxation method, originally developed by Akaike in 1999, uses Lagrange relaxation and is known for its ability to include the price change and possible better outputs, but the computation time is huge. However, the continuous advancement in computer technologies allows the use of higher-speed computers with more memory capacity. Therefore, in this paper the authors have tried to implement the method with adjustments and improvements in its algorithm to suit the current computing system. As a result, the computation time has been drastically reduced and more constraints can be included, which makes the scheduling a more realistic one. The case study of an open pit gold mine with 129 500 blocks can be solved considering the capacity constraints in 71 seconds. In previous case studies, the mined ore had to be processed or disposed of immediately. Now, stockpiling can be included as another option. Since the details of the algorithm are still being improved, the computation time is a little longer than the previous cases without the stockpiling option. However, it is found that scheduling with the stockpiling option is possible in a reasonable time. In conclusion, the 4D network relaxation method has become more useful with advances in computer technologies and provides better results.

Sep 26, 2011

By D David

Geometallurgy is often a misunderstood and poorly defined concept. The first thing the paper will attempt is to provide a definition of geometallurgy. Ultimately this paper has been written to provide guidance to geologists, mining engineers and processing professionals as to what geometallurgy means in the crucial early phases of a potential mining project between the time of discovery and the time of commencing construction, should this occur. The paper covers the options available for conducting a geometallurgical study of a resource or orebody, appropriate to the level of definition required in the projectÆs development cycle. The paper will then describe how the geometallurgical information generated is subsequently used in calculations, planning and preparation of reports designed to inform and reassure stakeholders, such as the market. Ultimately in a successful project, appropriate options adopted in the development phase will form the basis of an ongoing geometallurgical program that links the major site disciplines for the good of the operation.CITATION:David, D, 2013. Geometallurgical guidelines for miners, geologists and process engineers - discovery to design, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 129-132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

The tangible effects of leakage are presented graphically, and a technique for quantifying the leakage characteristics of a ventilation column using the æSolveÆ capabilities of a common spreadsheet is demonstrated. A case study of a working decline in Western Australia is used to demonstrate the potential for more realistic design of development ventilating systems, and for more cost effective management of the condition of the duct.

Jan 1, 2002

By A Calderon, J Harris, M Shi, D Viswanathan, C Ribeiro Duthie, P A. Kirsch

Mineral resource development activities impact the health and well-being of many people, from workers, to families and surrounding communities. In the current environment of corporate social responsibility life-of-mine planning considers that mining activities should be conducted in the best environmentally, socially and economically acceptable way for the entire life of the mine (ie from exploration to decommissioning and closure). In this context, the health impacts of mining extend throughout the life of the community from worker injury and chronic exposure to communicable and non-communicable causes of illness, through to family and community health and well-being. At the inaugural Life-of-Mine conference in July 2012, the authors proposed the life-of-mine in the life-of-community (LOMLOC) matrix as a framework for understanding issues at the interface between resource extraction operations and the surrounding environment.This paper reviews and compares health activities extracted from social and environmental reports published by selected major mining companies with American operations in Canada, Colombia and Brazil. These corporate approaches to public health management are mapped to the LOMLOC matrix to identify and compare trends and behaviour in corporate health investments. This analysis of how companies approach and prioritise health issues in the context of different regions, cultures and environmental drivers will serve as a resource for minerals industry managers, civil society and regulators regarding current health management approaches in this sector.CITATION:Ribeiro Duthie, C, Calderon, A, Viswanathan, D, ?Shi, M, Harris, J and Kirsch, P A, ?2014. Resource company investments in health – a life-of-mine / life-of-community perspective across America, in Proceedings Life-of-Mine 2014 , pp 349–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By C G. Sweeney

The underground mining industry is seeing unprecedented shortages in skilled labour. Migration to Australia being at an all-time low is a leading concern, with pandemic-induced border closures and lockdowns only exacerbating the skills shortage, not causing it. The skills shortage is forecast to peak in 2023 and remain high beyond 2025. With this skills shortage in mind, mining companies throughout Australia are trying to deal with stricter protocols around Health and Safety (H&S) legislation, as well as more stringent controls on quality assurance, particularly as underground mines are reaching greater depths and extending into ‘unchartered territory’. The cumulation of this is proving to be a major hurdle in ‘effective’ operational geotechnical management. The drive for automation in mining is bringing another level of complexity. However, ‘once automation is up and running, it presents the opportunity to access talent pools that may not normally be available. There is also a change in skillset that will be required to drive automation. ‘The top two emerging roles that will be critical for the future of the mining industry are artificial intelligence and machine learning (AI/ML) specialists, and process-automation specialists’ (Writer, 2021). If anything positive has come from the pandemic, it has shown that remote working can be effective and that the drive for automation and critical evaluation of skills required on-site should be given greater priority. UQ acknowledges that the industry is changing, and that digital technology is required to be offered in mining related disciplines. Industry and academia need to do more to promote geotechnical engineering in mining and balance the curriculum to suit the future of mining and make it more enticing. The average cost of a geotechnical failure is about $5 million in coalmines and can be into the hundreds of millions of dollars if production is affected (Cartledge Mining and Geotechnics, 2020). The cost of a good geotechnical design far outweighs the potential losses if a failure were to occur. This alludes to the growing importance of experienced geotechnical consultancies playing a pivotal role in managing mine site geotechnical hazards, while the industry is developing the next generation of geotechnical engineers.

Nov 29, 2022

By J Dyt, S Lyons

In the mining industry, crusher-related incidents have led to 15 reported deaths in Australia, New Zealand, and the USA between 1998 and 2007 (NSW Government Resources Regulator, 2024). The majority of these fatalities occurred during routine crusher maintenance tasks. A survey of quarry and mine site maintenance staff was completed to ascertain what they thought of such safety device to understand if beneficial and if so reasons if unused. Overall, findings show, staff perceived risks differently, cost, familiarity, device awareness and not front of mind, influenced adoption. This underscores the importance of asking the right questions involving maintenance and safety staff to lead to more proactive risk assessment.

Apr 16, 2024

The need for formalised geotechnical reporting has not been fully explored at many operations. With the continuing need to provide safer and more efficient workplaces, the requirement for good geotechnical reporting systems (as with other reporting systems) has become of greater importance.Historically, the risk from rockfalls has been the largest cause of fatal injuries in the underground mining industry. The response of the ground to mining is generally poorly documented at many mines. At Olympic Dam, it was found that the existing corporate hazard and incident reporting (HIR) procedure did not record enough specifics about geotechnical issues. A separate and more specific geotechnical reporting process was set up to address this problem.This paper examines the role that geotechnical reporting plays at the WMC Resources Olympic Dam Mine; from reporting and rectifying day-to-day geotechnical issues that affect the operation to documenting and analysing longer term trends.

Jan 1, 2004

By B Yang, L Wang, C Y. Ng

Flotation process intensification is often achieved through changing chemical reagent scheme or flotation machine or both, which likely brings a hefty burden to the flotation plants in terms of capital or operating expenditure. A novel approach to flotation process intensification is the use of acoustic sound, which has been demonstrated to be effective in improving the flotation of various mineral systems with different type of flotation cells. This approach was based on the dynamic stabilisation effect of acoustic sound on the flotation froth. The present work aims to understand the influence of various experimental conditions on the effectiveness of the approach. First, the effects of sound frequency and amplitude were studied with column flotation of silica particles. Results showed that the flotation performance was improved only within a certain range of frequencies and above certain amplitude. The study was then extended to the mechanical flotation of quartz particles with various size ranges and at two solids concentrations. With sound, the recoveries of different size fractions within the range of 20–212 μm were all increased. In particular, the recovery of 150–212 µm particles was increased from 0 per cent to approximately 25 per cent, demonstrating the potential for extending the upper limit of particle size in flotation by using acoustic sound. Furthermore, mechanical flotation of chalcopyrite particles at various collector dosages (50–150 g/t) was carried out with and without sound. Results showed that the increment of the final flotation recovery was increased with sound at different collector dosages. Overall, acoustic sound has the potential to be used as an effective and versatile method for flotation process intensification.

Aug 24, 2022

By M T. Grigoleit, M S. Schneider

The iron ore industry in Australia has, in recent years, experienced an unprecedented growth phase. But now that major expansions are moving into the operation phase, new challenges have emerged. Whereas initial planning may involve a few modelling studies, ongoing performance monitoring and improvement requires a different, more intense approach. This is especially important in the face of changing factors such as commodity prices, exchange rates and labour markets. Response time is key. As a mining operation proceeds from initial planning to daily operations, the time window for analysis shortens, going from months to weeks to days as the business matures.Simulation models and analysis tools are typically built and run by specialists in the planning phase, but then what? The investment has been made, but realised only once. What if further analysis could be carried out in-house, re-using existing models using up-to-the-minute data? Can we create virtual mines that run in parallel to live operations that allow computers to identify areas of a value creation or operational improvement? These questions can be answered by the innovative application of big data, simulation and predictive analytics. The future will be having this all integrated into one platform that offers, for the first time, an opportunity for non-experts to apply existing modelling and analysis assets – combined with live data – to deliver support for continuous improvement, and the ability to respond quickly to external changes in the best possible way, before they become big problems. These techniques will represent a step change in the ability for operations to maximise efficiency and will underpin the intelligent operations of the future. These issues are addressed in this paper.CITATION:Schneider, M S and Grigoleit, M T, 2015. Maximising productivity through big data, simulation and predictive analytics, in Proceedings Iron Ore 2015, pp 475–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015