Search Documents

Economic conditions dictated the lead time from concept to commissioning of the Kambalda C.I.P. Plant. The high gold price prevailing at the time the Victory ore-body was discovered provided the impetus to establish a treatment plant with the utmost haste. Consequently only limited metallurgical testing was possible. Fortunately the Kambalda Metallurgical Department had experienced gold metallurgists among its' staff. This enabled a rapid assessment to be made of the ore types to be treated. Flexibility was the keynote in the plant design. Overseas practice and experience was drawn upon extensively, but it was known that problems uniquE to the Kambalda Plant would be encountered due to the high nickel content of the C.I.P. Plant feed and the difficult clays in some of the areas. These fears were well founded and problems have been experienced. However the plant design has enabled these problems to be absorbed, if not overcome, and design production rates were achieved and maintained within three month; of start-up.

Jan 1, 1982

Water retention, water loss and delay in tailings storage rehabilitation are major challenges for many Coal Mines. Work by Stewart, Backer and Busch in the early 1980s suggested that there were improvements to be made in tailings dewatering and density by the addition of flocculant. This prompted ACARP, in cooperation with Bulga Coal Management (Xstrata), to initiate a research project investigating the impact of flocculant addition on tailings deposition density, water retention and the tendency for tailings to form surface crusts suitable for subsequent rehabilitation. A polyacrylamide-based flocculant (200 - 250 g/tds) was injected into the tailings line immediately prior to disposal into the impoundment area. The flocculated slurry rapidly released clear water and created a beach due to the immediate increase in deposition density. The deposition density increased from 35 per cent w/w to 61 per cent w/w solids within 24 hours and continued to increase to 75 per cent, seven days after treatment. The water capture at the tailings storage facility improved by more than 90 per cent; water which would otherwise be lost from the circuit through retention and evaporation. The impoundment capacity had nearly tripled due to the improvement in initial deposition density from 420 kg/m3 up to 1163 kg/m3. Four weeks after disposal surface crusts were forming on the storage facility, suggesting that there would be less delay between cessation and tailings storage rehabilitation.

Jan 1, 2008

By Elford H. S, Hughes J. F

The object of this paper is to bring before Members of the lnstitute the very important and much discussed question of scientifically prospecting for ores, oil, coal, etc.The paper is divided into three sections:SECTION l - Description of Geophysical Prospecting methods.(1) Sound-Vibration.(2) Magnetic.(3) Gravitometric.(4) Electrical.(a) Equipotential.(b) Electro-magnetic.(c) Schlumberger.(d) General.SECTION II - General discussion of Cicophysical Prospecting.SECTION III - Appendices.(1) Systematic summary of methods of survey.(2) Table of electrical conductivities.(3) Bibliography.SECTION I - DESCRIPTION O:F GEOPHYSICAL PROSPECTING METHODS.(1) SOUND-VIBRATION.THE transmission of sound waves or vibrations underground will depend on at least three factors: (a) Type of Rock. - Hard, dense rocks wiII transmit sound waves much more quickly than softer, more porous rocks. In the former the speed may be eight times that of the latter.(2) Uniformity of Rock. - Any variation in the texture, hardness, etc, wiII have an effect on and direction of transmission of the waves.

Jan 1, 1927

The Olympic Dam mining operation is some 520 kilometres NNW of Adelaide on the Roxby Downs Pastoral lease. The deposit containing copper, uranium, gold and silver was discovered in 1975 by Western Mining Corporation (WMC). A joint venture was formed in mid-1979 between WMC (51 per cent) and British Petroleum (BP, 49 per cent) for the development and exploitation of the deposit. WMC assumed 100 per cent ownership after acquiring BP's share in early-1993. Ore is won from a highly mechanised underground mining operation and processed to refined products. Current annual output from the mining of 3.0 Mt of ore is approximately 83 500 t of refined copper, 1400 t of uranium oxide, 750 kg of gold and 12 000 kg of silver. Conventional long hole, open stoping techniques are used to extract the production ore. Since stope production began in April 1988, full surveys and appraisals of stopes have been carried out to evaluate the integrity of the design and blasting techniques. This evaluation included the determination of the degree of dilution or non break that had occurred. Performance information also made it possible to re-design any adjacent stopes to retrieve remaining ore and conversely, avoid the chances of targeting backfilled material in the future. Performing stope surveys proved not only to be a time-consuming process but one fraught with access and line-of-sight problems. Occasionally it was not possible to obtain any stope survey data, and as was often the case with the mine pass system, rarely. In 1992 the sudden failure of the pillar between the fine ore and mullock passes and the subsequent delays to production, emphasised the need to effectively monitor pass wear. Initial information regarding the development of the Cavity Measurement System (CMS) prototype (Figure 1) indicated that it had the potential to solve these problems by the introduction of a remote scanning device into a cavity. Following a great deal of investigation, Olympic Dam Operations purchased the first CMS in Australia. This paper discusses its application for all underground void surveys and the procedures developed to manage both field and office requirements.

Jan 1, 1995

By B Whiteley, B Gee

The Northside Storage Tunnel is a TBM driven rock tunnel system designed to collect and store sewage from four major storm overflow points along the existing Northern Suburbs Ocean Outfall Sewer. At present, sewage overflows during wet weather are the main source of pollution for Sydney Harbour. The tunnel system comprises a 16 km long by 3.8 m to 6.5 m diameter tunnel from Lane Cove to the North Head Sewage Treatment Plant and a 4 km long by 6.3 m diameter branch tunnel from West Chatswood. The tunnel will have a typical rock cover of about 50 m to 150 m. Most of the tunnel alignment is contained within the Hawkesbury Sandstone Formation which is generally an excellent tunnelling stratum, and offers few geotechnical constraints. However, the tunnel is required to pass beneath incised palaeochannels at Middle Harbour and Manly with each palaeochannel containing about 70 m of sediment.Innovative geotechnical and geophysical investigations were undertaken to examine the tunnel route and characterise the rock beneath the palaeochannels. These investigations have located zones of poor quality rock beneath one palaeochannel in particular, suggesting significant stress relief had taken place in the rock at times of lower sealevel producing structural features indicative of valley bulging. This paper presents the geotechnical model developed for the tunnel, and the models and constraints for tunnelling beneath the palaeochannels.

Jan 1, 1999

By Munro DL

The Mary Kathleen uranium deposit is in north-west Queensland, approximately halfway between the townships of Mount Isa and Cloncurry, at long. 1400 009 E and lat. 200 44' S. The deposit Iwas discovered by prospectors of the Walton McConachy Syndicate early in July, 1954, and climaxed a very intensive ground search by hundreds of part-time prospectors. during the uranium boom from March to July 1954ò Numerous small deposits, mostly in the vicinity of Mount Isa, were discovered in various rock environments, but Mary Kathleen is the only large deposit and, apart from a few tons of hand sorted material from the Milo lease, is the only deposit that has been worked. Exploration of the surrounding area, and proving of the economic worth of the deposit, were conducted from the time of discovery until February 1956 by a geological team camped near the deposit. Proving was carried out by drilling a pattern of vertical and inclined diamond drillholes at fifty-foot centres over the outcrop. An adit was driven eastwards through the deposit. Metallurgical research and design work in the South Australian Department of Mines Adelaide Laboratories were based on core samples and bulk samples from the deposit. The signing of a contract in March 1956 with the British Atomic Energy Authority to supply 4500 short tons of uranium oxide allowed mining to commence, and enabled the planned construction of water supply, township and treatment plant to proceed. The open out mine and plant are now serviced by a modern township, four miles away, which is connected to Cloncurry and Mount Isa by road. Although little field work has been done since the exploration phase, this paper differs in interpretation from a previous paper (Matheson and Searl, 1956) in that it is based on a revised structural inter- pretation (Compana, 1958), detailed mapping of progressive exposures in the open out, and a re-examination of diamond drill cores.\

Jan 1, 1968

By L Whitbourn, K Yang, P C, E Ramanaidou

The potential of hyperspectral mineral mapping within a mine environment is demonstrated. Central to this capability has been the development of portable or vehicle-mounted, hyperspectral mine face-mapping systems. Data from these systems were used to detect subtle mineralogical variations and map their distribution across rock faces in a fashion that previously was not possible. In one study, the data usability was enhanced by ædrapingÆ the mineralogical determinations over a three-dimensional æmodelÆ of the rock-face. The eventual melding of the spectral mine face-mapping and three-dimensional spatial technologies will result in a new generation of mineralogical and structural information becoming available to mine geologists, engineers and metallurgists. Specific uses for spectrally-derived, mineral mapping data sets could include:ore grade mapping systems based on either direct detection of ore minerals themselves (eg iron and nickel oxides), or mineralogies that may be used as surrogates for ore-grade information (via various alteration minerals) after a suitable orientation survey; detecting mineralogies that have a deleterious effect on milling, metallurgical processing or have occupational health implications (talc, swelling clays, carbonates, asbestos, etc); selective mining and blending by collecting, processing and displaying such mineralogical images in near real-time to monitor ore grade and quality, and allow the separation of ore from waste during loading operations at the mine face; a mineral detection and mapping capability to assist in structural and geotechnical mine planning applications; and an enhanced geological detection and mapping capability for ore mineral species or alteration mineralogies that may be used to vector further mineralisation, update the existing mine ore model, or provide input to assist in the control of autonomous mining equipment. Within the Woodlawn open pit, Fe- and Mg-chlorites and phengitic- micas associated with sulfide mineralisation were detected and mapped. Subsequent studies using a second generation face-mapping system demonstrated the direct detection of ore-grade materials for iron-ore and nickel laterite mining activities. Satisfactory and meaningful results were extracted from data that were collected under a variety of challenging conditions. However, these non-ideal climatic and operational conditions would be expected under most operational situations in a mine environment. Development of a system using artificial illumination, permitting night-time (and eventually underground) operation and elimination of atmospheric absorption effects is underway.

Jan 1, 2006

By Stevens P

The Isa Mine of Mount Isa Mines Limited currently produces 5.4 million tonnes of copper ore and 3.3 million tonnes of silver, lead and zinc ore annually. Of this, 5.1 million tonnes of copper ore and 2.2 million tonnes of silver-lead-zinc ore is produced by sublevel open stoping. This paper summarises the capabilities, operating practices and problems encountered with current production drilling practices used to drill sublevel open stopes at Mount Isa.

Jan 1, 1982

This paper will discuss specifically the performances of vibrating screens having circular motion with inclined decks and linear motion with horizontal or near horizontal decks and both related mainly to coal, metalliferous, and other granulated solids applications where screening and efficient classification is required. Some misconceptions have been applied in the past with regard to making a screen type selection using either circular throw or linear throw and therefore this paper will endeavour to clarify these misconceptions.

Jan 1, 1984

By B Cronin, M Gao, M F. Young

Fine grinding technology has become extremely important for Mount Isa Mines Limited in the last decade for flowsheet development for the McArthur River deposit and in rejuvenating the Lead-Zinc Concentrator at Mount Isa. Regrinding products with 80 per cent passing seven microns and 12 microns were required, respectively, for the McArthur River ore and the Lead-Zinc Concentrator at Mount Isa. Development of the ISAMILL, a horizontal stirred mill with a gross mill volume of 4000 litres (a net volume of 3000 litres), has been successful in delivering the required grinding product sizes with an energy consumption acceptable to a mining operation. The ISAMILL performance for processing both lead and zinc streams at Mount Isa is discussed in this paper, including the milling energy efficiency, the media wear and the size-by-size recovery data for one flotation process following the fine regrinding stage. The potential use of the ISAMILL technology at various phases of the mining cycle is also discussed.

Jan 1, 1998

The long continuing controversy over the Origin of fusain, whether it is a product of primeval forest fires, or of special conditions of weathering (including bacterial decay) of the vegetal debris concerned prior to, burial, has now been extended, to include the possibility that fusain is a product of the coalifaction process subsequent to deposition, so that doubt may reach even to its time of formation.The conflicting views on this point are summarised in the following quotations from two recent publications (my italics in each quotation):1. "Recent observations made in peat and brown coal deposits in Australia, England and Germany strongly suggest that practically all fusain is formed by coalifaction after deposition and 'preliminary compression. In deposits of advanced brown coal rank, it normally takes the shape of pieces of wood compressed parallel to the bedding plane; and some fragments consisting partly of fusain and partly of vitrain exhibit the same amount of compression throughout. This would seem to indicate fusinisation after burial, as hard brittle charcoal would be crushed, or else retain its original irregular shape if strong enough to withstand pressure.In some immature deposits, however, where cover is of a hydrostatic nature rather than a vertical compressionar force, occasional pieces of fusinised wood showing very little flattening are present, but such immature deposits seldom contain the proportion of fusain found in higher rank coals. In view of this, and the possibility of introduction of charcoal into peat deposits, it is felt that a small amount of the fusain in coal may represent wood charred before burial, but most of it almost certaInly originated as a product of fusinisation after burial" (Dulhunty, 1948, p.14).

Jan 1, 1953

By H Holmstr÷m, A Widerlund, M Lindvall

At the Kristineberg mine in northern Sweden sulfide-rich, poorly buffered tailings have been deposited in five impoundments located along a valley. The tailings area has been remediated by applying a combination of till cover and flooding. A new method that has been applied to parts of the tailings area is to raise the groundwater table to saturate the tailings. By increasing pH by liming, thereby reducing metal mobility, a water-covered downstream impoundment is functioning as a trap for metals released from the till-covered impoundments upstream. In this paper the efficiency of the system approach used at Kristineberg is evaluated. Progressive changes of water quality from groundwater in the upstream till-covered impoundments via surface streams within the pond system to the water in the flooded downstream pond and its outlet are described. The results show that the system approach used in the design of the remediation programme of the tailings works as planned. The sulfide oxidation rate has decreased in the till-covered impoundments, and, as predicted, there is an out-flush of old weathering products which will continue for at least five years before equilibrium is reached. The groundwater in the till-covered impoundments has high concentrations of Fe, S, Mg and Zn, but the concentrations of metals such as Cu, Cd and Pb are much lower than before the till cover was applied. The limed pond is an efficient metal trap, with concentrations as high as 2.76 per cent Zn and 0.28 per cent Cu in the calcite-gypsum sludge developed on the tailings. The outlet from the flooded pond, and thus from the whole mining area, releases small amounts of metals to the recipient in comparison to the amounts that are in movement within the mining area. During the period May to November, 13 kg dissolved Zn and 111 kg particulate Zn was released to the recipient, whereas a total of 27 000 kg was transported by surface water within the impoundment system during the same period. The results from Kristineberg show that when planning remediation of complex mining areas, it is useful to adopt a system approach in which different methods are used on different parts of the area along the flow path of the drainage water, whereas flooding of the downstream pond is the key to the performance of the entire system.

Jan 1, 2003

Where vertical or near vertical faces are required in open excavations in soils and rocks, some form of stabilization of the 'cut is often necessary. Stressed anchors either alone or in combination with steel, timber or concrete-lagging are often an economical and versatile means of providing support. Stressed anchors are also-a very economical means of anchoring a wide range of structures such as dams, cranes, transmission towers, retaining walls, spillway aprons, bridge piers; and - stacks. The anchors need not be stressed always on installation.other than to proof load them. A number of examples illustrate some of-the more practical aspects of.the design and construction techniques used. No new methods of design or construction are involved, but merely some consolidation of the engineering design, soil and rock mechanics,thinking applied to the stressed anchor tech- nique.

Jan 1, 1971

By M D. Basuki Dwi Priyono

The Toguraci low sulfidation epithermal gold vein deposits are located 2 km WSW from the Gosowong mine and form part of the Gosowong Goldfield. The goldfield lies within a Neogene magmatic arc on Halmahera Island, North Maluku Province, East Indonesia. The terrain is moderate to steep, rainforested, and poorly outcropping. Exploration and mining operations are being carried out within the PT Nusa Halmahera Minerals Contract of Work (exploration tenement) jointly owned by Newcrest Mining Ltd (82.5 per cent, operator) and PT Aneka Tambang Tbk. (17.5 per cent). First pass exploration of the Gosowong area began late 1992 resulting in the discovery of weakly developed porphyry copper mineralisation (named Bora) at Toguraci in 1993. Early in the evaluation of this porphyry an overprinting epithermal Au/Ag mineralisation event was recognised, however exploration focus remained on the Bora porphyry deposit for some time. The discovery of the nearby Gosowong epithermal gold deposit and the exploration of other prospects in the area further diverted attention and funds from Toguraci. It was not until year 2000 that Toguraci was seriously reevaluated as part of a detailed appraisal of the epithermal gold potential within a 5 km radius of the Gosowong gold mine. A fly-camp based drilling campaign using man-portable rigs was undertaken between August 2000 and March 2002. All exploration at Toguraci was then stopped pending government approvals to mine. These were finally issued in May 2003 and immediately drilling restarted and pre-mine approvals (eg the environmental impact study) were sought and granted. The first Toguraci gold bar was poured in February 2004. Exploration at Toguraci and elsewhere in the Gosowong Goldfield continues today.

Jan 1, 2004

By Haslam C. O, Taylor S

Four historical periods of Australian lead-zinc-silver exploration and development are identified.In the first period, 1841-1900, Australia's deeply weathered surface yielded bonanza deposits. The outcrops of easily worked secondary ores, enriched in silver and lead, were discovered by prospectors with the incentive of production at times of high silver price. Districts discovered in this period still contributed, in 1982, 60 per cent of Australia's lead-zinc production, mainly from Broken Hill.The second period 1901-1944, was one of strong mine development but stagnant lead-zinc-silver exploration. Mount Isa was discovered and developed, but otherwise effort was devoted mainly to the mining of deposit extensions and to the metallurgical flotation of zinc. The deposit discovery rate was low but the discovery of Mount Isa was so significant that discoveries of this period contributed, in 1982, 30 per cent of Australia's lead-zinc production.The third period 1945-1972 was one of re-invigorated exploration.New geological and geophysical surveys, developing concepts of ore genesis, and worldwide comparisons of orebody settings improved target area selection. Evolving remote sensing methods, and rapid analytical techniques, assisted detection of lead-zinc deposits. Initiation of exploration led to discovery:1. in regions of previously unsuspected lead-zinc-silver potential (Sorby Hills, Mons Cupri, Golden Grove).2. of poorly exposed deposits in recognized mineral districts (Hilton, H.Y.C., Woodlawn, Elura, Que River).3. during active exploration for another commodity (Brown's, Woodcutters, Mary River, Beltana, Lady Loretla and Pegmont).The period saw a sustained growth in lead-zinc-silver production mainly from established operations. Mines discovered during the third period contributed, in 1982, 7 per cent of Australia's lead-zinc production.In the fourth period from 1973 to the present, exploration initiatives became fewer but resulted in continued discovery of poorly exposed deposits at Teutonic Bore, Thalanga, Benambra, Scuddles, Hellyer, and Jillawarra. Development initiatives strengthened in the period and production commenced at Woodlawn, Teutonic Bore, Que River and Elura; pre-feasibility work commenced at Scuddles, Hilton, Lady Loretta and Thalanga.

Jan 1, 1984

By J Austin, R Bitencourt

Differences between the long-term model (LTM) and mine geology system (MGS) grade control block-outs on a blast block scale can impose difficulties to planning crusher feed grade and tonnes on a monthly to weekly blend basis. Detailed geological input to short-term planning has been integral to improve the performance and reduce risk in six-week to three-month production schedules and local variability in tonnage and grades is often not accurately represented in the LTM. The challenge of producing to combined target specifications from different mine sites in an integrated mine to ship business has been reduced with the creation of blast blockout-based short-term model. These short-term blast block models (STBBM or STM) are robust predictive tools created for upcoming benches of current mining areas by firstly collecting data from the pit in the form of bench and face mapping and projecting the structure and stratigraphy down to the next bench. A wire-frame of the projected contacts based on material destination from production blockouts is created and then checked against the LTM. Blast block data from the bench above including assay results and material logging is extracted and validated according to the projected wire-frames (geozones). Individual blast blocks and a full block model are created for each bench production defined by the STP (bench plans). Data output from the STM is in a compatible format for import into scheduling specific software packages. Additional information is incorporated into the STM to allow querying of drill penetration rates, predicted powder factors, material hardness and feed type to further aid in the production planning process and cost forecasting. To date, reconciliation of the STM has been pleasing and certainly an improvement on the LTM, especially in areas where variability is higher due to geological complexity. Short-term predictions derived from in-pit geological observations allow mine planners to more confidently decide on mining block sizes and schedule tonnages and grades, reducing the risk component attached to developing production schedules based directly upon long-term orebody models and mine plans.

Jan 1, 2005

By J E. Lynch

The Mt Leyshon gold deposit produced in excess of three million ounces of gold and considerable silver over a period of approximately 130 years. Most of this production occurred between 1987 and 2001. Mining commenced in 1872, however it was highly likely that Chinese miners were not only removing alluvial gold from the area but were also mining very rich æreefÆ gold. Records for early alluvial and hard rock mining do not exist, however gold production was probably considerable. In the early 1980s Marathon Petroleum (Australia) Ltd (MPAL) joint ventured into the Mt Leyshon area which had been held as a mining lease by Noranda Australia Ltd since 1968. Noranda at that time was concentrating its exploration effort on the Balcooma base metal prospect areas to the north of Charters Towers. In early 1982 MPALs parent company was taken over by US Steel. This led to an opportunity for MPALs Australian management to purchase all tenements and licences (except for coal, oil and gas) which were duly purchased for $US 1 million. At this time MPAL had a remarkable array of gold tenements (many of which were subsequently mined by other companies) and Mt Leyshon was considered to be the highlight. Early æseedÆ capital ($A 3.1 million) was raised with backers being the Bank of America, the NSW Government Superannuation Scheme, Westpac, private individuals and a Queensland grocery chain by the name of æJack the SlasherÆ.

Jan 1, 2004

By H Arvidson, D Guibal

This paper presents updated interpretations of controls on mineralisation in C Deposit and highlights structural features that influence the geometry of mineralisation domains used in resource estimation. The Area C mining lease is located in the central Hamersley Province, ~100 km WNW of Newman, Western Australia, and contains resources of approximately 1100 Mt of Marra Mamba and Brockman iron mineralisation. C Deposit is located within Area C, on the northern limb of the Weeli Wolli anticline, and mineralisation is hosted predominantly in the Mt Newman Member of the Marra Mamba Formation. Production from C Deposit began in August 2003, following mining of a 950 000 tonne bulk sample in 2002. Recent mapping in the bulk-sample pit and updated interpretations by BHP Billiton geologists have highlighted the significance of structural controls on mineralisation in C Deposit and their influence on the thickness of mineralisation, which ranges from 20 to 80 metres. Structural controls on the geometry and continuity of mineralised domains include south-dipping thrust faults that developed along the Mount Newman/West Angela contact, folds associated with thrust fault development, steeply dipping stratigraphic contacts in the hanging wall of the thrust faults, and gently north-dipping stratigraphic contacts. Thrust faults and folds in C Deposit are significant for two main reasons: their formation resulted in the thickening of the main ore-hosting units in the Mount Newman Member; and faults and folded stratigraphic contacts provided conduits for supergene metasomatic-enrichment processes that produce high-grade iron mineralisation.The implications of this interpretation for the definition of the resource estimation domains are discussed, and suggestions are made for a better integration of geology into the data acquisition and estimation process.

Jan 1, 2005

By Chitombo GPF

The dilution of blasted ore with cemented backfill materials has been recognised as a significant factor influencing the economics of some underground metalliferous mining operations. Several mechanisms have heen identified as possible causes of fill failures. The purpose of this study was to determine the possibility of damage as the result of one mechanism, that of production blasting adjacent to bodies of cemented hydraulic fill (CHF). A vibration amplitude transfer function has been developed to model the transmission of blast vibrations from the source, through ore, across the ore to CHF interface and into the CHF mass. The model may be applied in the near field. The model has permitted estimation of vibration amplitude at a point in a CHF mass, to which damage criteria may be applied. A number of assumptions and simplifications have been made to render the problem relatively tractable. Ore and CHF material characteristics recorded by a number of authors were utilised to formulate preliminary damage estimations. A simple application of the amplitude transfer model indicated that a zone of plastically deformed CHF would be produced, and would extend to a distance of approximately 0.5 metres from the interface into the CHF. A sensitivity analysis was also conducted, that indicated that the zone of plastic deformation would be more extensive given appropriate conditions. Recommendations for further model development and future laboratory and field investigations have been made.

Jan 1, 1998

By Holcombe R. J, Dobos S. K, Little T. R

Blue amphibole-bearing rocks in the North D'aguilar Block of southeast Queensland occur either as relict pods and lenses within regionally extensive greenschist facies phyllites and schists or as blocks entrained in serpentinite-matrix melange. Epidote + crossite-bearing varieties predominate and formed under conditions consistent with underplating and high P:T metamorphism in a subduction-related tectonic environment. Neither lawsonite nor jadeite has been observed and metamorphic conditions are estimated at 380-4500C for pressures of 0.5-0.8 GPa. High P:T metamorphism occurred during the earliest stages of deformation and was superimposed upon protoliths of inferred Late Devonian - Early Carboniferous age, including mafic volcanics, tuffs and coarse volcaniclastic breccias as well as pelagic and henipelagic sediments, all of which have undergone varying degrees of over-printing to the greenschist facies. Greenschist facies metamorphism occurred during the second phase of deformation and was associated with the formation of mainly flat-lying or subhorizontal structures; it followed the cessation of subduction and occurred in response to either thermal relaxation during uplift or the imposition of regional heating induced by crustal thickening and/or synkinanatic granite emplacement. Uplift and cooling of the high P:T rocks was completed by 260-265 Ma and may have occurred in response to the same extensional processes which gave rise to the onset of rifting in the adjacent Esk Trough.

Jan 1, 1990