Search Documents

By Hatcher MI

Exploration undertaken at Copley diapir has located several occurrences of oxidized supergene and primary sulphide copper mineralization at the margin of the diapir or in adjacent country rocks. The mineraliza- tion is related to carbonate-rich epigenetic solutions which moved along major structural features closely associated with the intru sive diapir.

Jan 1, 1975

By G Giles

One of the main tools used by mining operations to mitigate the risk of rock burst is the installation of a so-called ædynamic resistantÆ support system. Such systems are designed to absorb the impact of shockwaves created by mine-induced seismic events. Dynamic support must be strong and capable of sustaining high loads and, at the same time, they have to be flexible and accommodate large deformation. A dynamic support system is therefore a system capable of absorbing a high quantity of energy. Ground support systems are composed of rock reinforcement (rock bolts or cable bolts) and surface support (mesh or shotcrete). In terms of surface support, fibre-reinforced shotcrete is increasingly seen as the industry preferred solution when difficult ground conditions are experienced, including areas of high seismic hazard. A thick layer of shotcrete is certainly strong but it is by no means flexible. Normal weld-mesh has some flexibility, but it is not very strong. The Australian Centre for Geomechanics (ACG), in collaboration with Onesteel Reinforcing Pty Ltd, is currently working on a new high-energy absorption mesh that combines strength and flexibility. The new mesh can be installed with a jumbo, in a similar way as the widely used sheet of weld-mesh. This paper describes the development of this new mesh system.

Jan 1, 2008

By P Andrieux

By 1996 ground control-related problems at Brunswick Mine had raised serious concerns regarding the safe and economical extraction of large portions of the reserves. These difficulties were mainly caused by high stress levels in pillars, instabilities resulting from wide spans supported by ageing support elements, and chronic difficulties supplying rock fill from the surface quarry to the underground workings, which resulted in many large voids remaining open for long periods of time. Significant changes have been implemented at the site since 1996, amongst which were a change of mining method, the introduction of paste backfill, the establishment of stress management measures, and the introduction of shotcrete on a large-scale. This paper focuses on the regional ground conditions associated with both the previously used primary-secondary mining method and the newly implemented pyramidal pillarless technique, as well as on some of the stress management measures implemented at the mine.

Jan 1, 2000

By P J. Scales, D Boger

Technological advancements in mineral processing have increased the feasibility of refining low-grade ores. Because of this progression and continual depletion of high-grade ore deposits, much larger volumes of waste material are produced. At the same time, increasing environmental legislation and cost competitiveness dictate that these wastes be disposed of in a manner that is both environmentally acceptable and economically viable. To achieve these criteria, many mineral processing industries are dewatering waste streams in order to reduce the volume of tailings and increase water and reagent recovery. The subsequent dry disposal of these highly concentrated mineral tailings requires a thorough understanding of the effects of dewatering on the flow characteristics. Dry disposal represents a paradigm shift in engineering. The tailings are engineered to suit the disposal requirements, as opposed to engineering a facility to accommodate the tailings. It is therefore important to understand how the material properties and operational parameters can be modified to produce the desired tailings flow and deposition characteristics. As concentrated suspensions usually exhibit non-Newtonian behaviour, determination of the disposal plant operating conditions requires a thorough understanding of the rheological characteristics of the material. The implementation and optimisation of dry disposal methods involves three concurrent and interdependent rheological studies to determine:the concentration required to achieve the optimum spreading and drying characteristics of the tailings once deposited; the optimum conditions for pipeline transport; and the feasibility of dewatering the slurry to the required concentration. The paper presents an overview of the issues pertinent to management of the flow properties and processing of dewatered waste streams.

Jan 1, 2002

By D R. Rankin, J J. Fuykschot

Forrestania Nickel Mines is owned and operated by Outokumpu Mining Australia Pty Ltd and is situated 400 km east of Perth, WA in the Forrestania Greenstone Belt. Production started in late-1992 at a rate of 600 ktpa and reserves were exhausted in August 1999. Cosmic Boy is the largest of three mines worked and operates in a high stress environment with both very high and very low rock mass strength domains. Stoping commenced in 1995 using conventional benching with long hole slot rises but because of drilling and blasting problems the mine switched to airleg rising. In 1997 the mining method was changed to smaller scale up hole retreat benching with each stope requiring a slot rise of up to 16 m length. This method does not allow top access to the rise location and so airleg rising was used until mid-1998. At this stage mining was approaching areas of higher stress for which it was clear that an alternative to this entry method of rising was required. Small diameter raise boring and Cubex rigs were considered but because of the set up costs were not considered to be viable. Since the ore is relatively soft, burn cuts were developed to make use of specially designed 152, 203 and 254 mm diameter reamer bits (depending on the rise length) and drilled with conventional long hole drilling equipment. These rises are fired in one blast together with the slot rings. In the northern lower section of the mine (below 400 m) the principle stress has been estimated at 60 MPa and this causes minor strain bursting in BIF development headings and loose material to form on walls and backs. Trials of destress blasting modelled on Canadian experience has greatly reduced strain bursting at the face. However only around 300 m of development was affected and so this method had not been optimised when mine development was completed.

Jan 1, 1999

By Grant BPM

The lower levels at the CSA Mine have been developed to mine reserves between theNo.7 level and No.9 level.Work on major excavations for the project began during 1982 with the develop-ment of the crusher chamber, on No.9 level. The brows and walls were pre-dowelled to improve stability before mining by mass blasting techniques.At the same time work commenced on theextension of No.2 Shaft from No.7 level toNo.11 level. The shaft was stripped, using hand held drilling, to a raise bored holeand concrete lined to a diameter of 5.5 metres. Plats were developed at No.8 level, No.9level and the loading station.

Jan 1, 1985

By Mills KW

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the loading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992

Naturally occurring rutile contains approximately 96 per cent titanium dioxide (Ti02), whereas the product from the ilmenite reduction - aeration upgrading process, "sub- rutile", contains only about 92 per cent Ti02. Therefore, there is an-incentive to lift the quality of sub-rutile by removing transition metal impurities, in order to supply a more valuable and marketable product, particularly for the chloride-route pigment producers. Previous studies have shown that the sub- rutile residual iron content (of approximately 4 per cent) and residual manganese content (of approximately 1.5 per cent) are chemically bound within the titanium-oxygen mineral lattice, and are most difficult to remove by simple leaching methods. In attempts to improve their eventual removal, a simple process modification has been successfully investigated in laboratory scale trials. Transition metal sulphides have been formed in the reduced ilmenite by using a "sulphur-doping" technique during reduction (metallization) conducted at controlled temperatures. These compounds give rise to greatly enhanced dissolution of the unwanted transition metal constituents during the sub- sequent aeration and acid washing steps. Thus, the manganese content of the final sulphur- doped, reduced-aerated, acid washed product can be reduced by about 90 per cent to 0.2 per cent, and the iron content by about 70 per cent to less than 1.5 per cent, in comparison with those levels remaining after unmodified pro- cessing. Additions of sulphur as low as 2 per cent of the weight of the ilmenite have proven satisfactory. Preliminary studies reveal that the modified process is economically feasible. These results suggest that the sulphur content of the Collie coal char used in an unmodified reduction step must exert some influence on the eventual removal of iron and manganese during aeration and acid washing.

Jan 1, 1973

Don Hausen was a pioneer in the field of quantitative mineralogy. Methodology that he developed at Newmont almost 40 years ago is still employed today, only the technology has advanced. Petrographic methods were stressed with an emphasis on alteration, mineralisation and paragenesis. Methodologies employed by Don on the Carlin deposit were applied to developing the Carlin Trend by helping to work out lithology and structure, which ultimately led to the discovery of deep high-grade deposits. Quantitative methods used by Don on San Manuel, Copper Creek and Superior, Arizona were applied to the development of the Batu Hijau Deposit in Indonesia. Advancements in technology since DonÆs time have made the mineralogist much more efficient. Manual measurement of peak heights off of strip charts for semiquantitative XRD has been replaced by software that does Rietveld refinement and whole pattern fitting. Hand contouring of XRD data has been replaced by digitised data incorporated into geologic models. Optical point counting, which would take a dayÆs work to process 1000 points, has been replaced by automated SEM methods where 20 000 points are possible in an hour. The use of the optical microscope remains relatively unchanged, and still remains as Don emphasised the æeyesÆ of mineral exploration. However, the information can be relayed much more quickly with digital image capture and electronic data transfer. Don insisted on becoming involved in projects at the grassroots level and supporting the project through mine closure. This made the mineralogist a liaison between exploration geologists, mine geologists, metallurgists and mine engineers. The methodology that Don helped develop continues to provide invaluable support to Newmont geologists and metallurgists worldwide today.

Jan 1, 2008

By Scott B. R

Bougainville's copper mine is located on the west slope of the Crown Prince Range on Bougainville. A high grade copper concentrate is produced for sale to overseas customers. Production planning which was originally based on pilot plant data has developed progressively since commissioning of the concentrator in 1972. Pilot plant data and mine sampling have been supplanted by the correlation of concentrator performance with ore sources, as the basis for short term planning. The influence of accurate sampling is reflected in 1. hourly shift control, 2. the daily milling statement, 3. the prediction of the characteristics of ore from various mine locations, 4. production reconciliation, and 5. the control of copper losses. The mechanical and electrical failures of the original sampling system emphasized the need for a reliable, automatic sampling facility. The development of a pneumatic drive mechanism, which has now been fully field tested, was undertaken.

Jan 1, 1976

Ranger Uranium Mines (RUM) operates an open cut located in the Top End of the North- ern Territory. Strict environmental controls govern all operations and the water management requirements have the greatest impact on mine planning. The two main goals of planning are to provide mill feed and to mine sufficient suitable quality waste rock for ongoing con- struction of the tailings dam. Early planning concentrated on staged development of the pit to provide access to as much ore as possible for a given amount of development. All waste was considered to be suitable construction material. Grade control of crusher feed was the main problem in planning, as wide vari- ations occur in ore grade over relatively short distances. Water management for the site ope- rates a no release' system for contaminated waters. Design storage has proven inadequate, and the open cut has been used as the extra storage. As construction of future stages of the tailings dam requires non-mineralised rock materials which meet specific quality criteria, the mine has had to re-examine long term plan- ning and pit development strategies. This has entailed the collection of much data not re- quired under normal mining conditions, such as the assaying of waste drill core. The overall impact on mine planning of the environmental regulations has been to alter the philosophy of earlier planning, making it necessary to create a new strategy for pit development with

Jan 1, 1984

This paper traces briefly the reasoning which led to the decision to extend the existing internal shaft at the Rosebery Mine and to instal underground a larger winder (No. 2 Hoist) with capacity to handle all hoisting requirements to a depth of approximately 2,500 ft. on an incline varying from 83" to 55" to the horizontal. It then covers the specifications and selection of the winder, the design of the winch chamber, rope raise and bins, the excavation, support and lining of the chambers and the transport to site and installation of the machinery. Finally a brief description is given of the mechanical and electrical parts of the winder.INTRODUCTIONThe existing shaft winder on the internal inclined shaft situated on No. 8 Level of the Rosebery Mine had reached the limit of its capacity. Hoisting 21-ton capacity skips in balance, with a 13/16-in. diameter rope, it required four layers of rope on the 3 ft. 6 in.drums to reach the loading station under No. 12 level at a depth of 864 ft. (Fig. 1). This entailed heavy wear on the multi-layered rope and heavy stresses on the cheeks of the drums. Continuous working on three shifts was necessary to handle ore, men and materials, and a hold-up from any cause whatever meant an interruption to production on the lower levels of the mine. The maximum output of the hoist whilst hoisting from the No. 12 level loading station was 50 tons per hour. It was obvious therefore, that a larger winder was required if output was to be maintained.Diamond drilling had proved the existence of sufficient ore at depths well below No. 12 to warrant exploitation and a decision had to be reached on the means of hoisting this ore.

Jan 1, 1958

By F A. Rosyid

Mineral resources are national assets which must be capitalised for national development. Those assets should be transferred into real economic capital and then into social capital to achieve national/regional prosperity. Successful development in the mining industry will depend on the correctness in determining the role of mining industries for regional development. Using the context of sustainable development, this paper will analyse the concept and process of mining industry development as an accelerator to achieve regional sustainable development, using the mining operations of PT Newmont Nusa Tenggara (PT NNT) in Batuhijau, Sumbawa Barat Regency as a case study. In the premining activity phase, Sumbawa Barat was dependent on the agricultural sector. Agriculture contributed around 40 per cent of the regional gross domestic product (GDP). Meanwhile, in the activity phase, mining became the sector with the biggest contribution to regional economy. From its operation in Batuhijau, PT NNT contributed around 70 per cent of the regional GDP per year since 2001. In year 2000, the GDP had increased 170 per cent from its figure in 1999. However, due to its depleting reserve, PT NNT will finish its activity in Batuhijau by year 2015. Consequently, the Government of Sumbawa Barat Regency must develop other sectors in the post-mining phase to sustain economic development. Based on location quotient (LQ) and input-output analyses, Sumbawa Barat should develop its priority sectors, ie agriculture, trading and hotel, services and construction to achieve sustainability after mining life. Development of these non-mineral sectors is expected to sustain economic growth in the region.

Jan 1, 2008

It may at first sight appear somewhat presumptuous for the writer to attempt to discuss a subject in which he cannot pretend to possess any special scientific training; but a sufficient apology can surely be found in the fact that a very large percentage of the accidents from explosives occurring in metalliferous mines is traceable to the ignorance of the characteristics of these compounds by the miners who have to handle them, and to their deliberate disobedience of the rules laid down for their guidance by the manufacturers, the government regulations, or the special rules of the mines.The only method which promises any possibility of improvement upon these conditions is to substitute reason and understanding for the rule-of-thumb principle which says "you should do this" or "you should not do that." In the one case his own knowledge and intelligence enables the miner to avoid any dangerous practice in the other his inclination prompts him to do anything which will save time, provided he is not found out or at best trusting to his memory to tell him what is dangerous, without the reasoning which makes that memory easy.Another evil of rule-of-thumb knowledge is that, from its very nature, it prevents adaptability, and so we find that old miners, who learnt blasting in the days of black powder, cannot understand why high explosives do not require heavy tamping, or because copper bars are permitted in tamping powder they should not be used with other explosives...

Jan 1, 1903

A standard practice of auditing mill designs has developed in the mining industry. The purported aim of this task is to ensure that the mill being offered conforms to the design specification, thus reducing the purchaserÆs risk. However, careful examination of the auditing methods used in the past shows that this is not the case. In some cases, what auditors have been providing is effectively a quality assurance check of the input data, not a full independent audit of the vendorÆs design. It will be shown that these past auditing methods have contributed to the stagnation of mill specification development. This lack of specification improvement combined with the current trend towards increased allowable fatigue stress ranges can result in an increase in risk for the purchaser.

Jan 1, 2002

By Fabjanczyk M. W

Artificial ground support has developed into a refined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bolt is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

This paper is a summary of the general theory of sampling published by the author in 1975. Sampling is a random process and its the- ory is a study of the, numerous errors liable to take place in the course of its realization. A complete sampling scheme is a sequence of sampling (proper) and preparation stages . At each stage, the total error ET is the sum of : -.Sampling errors EE arising from the selection process itself. -Preparation errors EZ arising from the operations (crushing, transfer...) sup- ported by the sampled material. ET a EE + EZ . At each sampling stage, the (total) sampling error EE is the sum of seven inde- pendent errors : - Weighting error ED resulting from the non-uniformity of the density or rate-of-flow of the sampled material. - Integration error EI1 resulting from the long-range distribution heterogeneity of the sampled material. - Periodicity error EI3 resulting even- tually from periodic quality variations of the sampled material.

Jan 1, 1976

The preconcentration of uranium ore by radiometric ore sorting at Mary Kathleen Uranium Ltd. is described. The operation of the ore sorting machines is discussed in detail and performance results obtained with the existing system are presented.

Jan 1, 1978

By Ogilvie M

South Bulli is the oldest and largest underground coal mine in Australia. Two longwall units are in operation and current production is 2.5 to 3 million tonnes of run of mine product per year with a workforce of 600. Prior to 1984 a workforce of around 1,200 produced 1.5 million tonnes. Advances in technology can. of course, account for some of this gain, but the changes made in the human resources area are also seen as playing a major role in South Bulli emerging as a reasonably stable operation.The human resources strategy adopted recognises the value of the workforce and is aimed at not only fostering cooperation as all levels, but also making employees aware of the direct contribution they can make to the success of the enterprise.

Jan 1, 1991

By Durucan S

Uncertainty due to spatial and temporal variability of different pollutants found in soil, water and air is an important issue in the modelling of environmental impacts. Recognition of spatial environmental patterns is relatively straightforward to achieve by applying most of the well-known artificial neural networks or adopting a stochastic approach. However, it is the temporal component of the environmental variables that makes modelling of the environmental pollutants particularly complicated and challenging. This paper presents the results of a case study investigating the artificial neural network performance when modelling the spatio-temporal behaviour of environmental pollutants. The test case involved the modelling and prediction of the distribution of water quality indicators along a river from the point of discharge of treated mine effluents. The behaviour of river water quality indicators is rather complex and shows a lot of fluctuations due to a number of hydrochemical, hydrobiological and hydrodynamic factors. Results obtained in this study indicate that artificial neural networks provide a very powerful and robust method for simultaneous modelling of spatio-temporal behaviour of environmental pollutants.

Jan 1, 1995