Search Documents

Utah Development Company operates a mine at Blackwater with a present annual production of 4 000 000 tonnes of coking coal. Mineable seams outcropping on the company's lease are part of the Permian Mammoth Rangal Coal Measures. Current operations are based pre- dominantly on the Main Lower seam. Coal quality variations occur along the seam strike, in the direction of seam dip, within the seam plies and in isolated anomalous areas. Raw coal of non-specification quality is washed to reduce ash and sulphur and to improve the free swelling index. Raw coal meeting specification quality is sent directly to product, by-passing the washplant. Careful attention to mining, coal preparation and product blending is necessary to ensure that the combined product meets specifications.

Jan 1, 1974

By C Standing, R Lacourt Rodrigues, C Q

The value of iron ore depends on the grade of the contaminants. Scheduled iron, and the associated contaminants, provides mine planners with a measure of stockpile feed and blending requirements. Blending at the stockpiles is one approach to optimising iron grade, while minimising the variability of contaminant grades. These schedules are typically based on resource models incorporating geology and iron and contaminant grades. Resource models reflect best estimates of trends for each of the elements rather than the potential variability, which is critical for accurate short-term blending. Conditional simulation provides a tool to describe the likely variability of each element. Only recently has conditional simulation technology allowed the inherent correlation between elements to be incorporated into the process. This paper presents the stepwise co-simulation process used to simulate and describe multi-element variability for effective mine planning. A case study using the multi-element conditional simulation and the subsequent uncertainty in the schedule and stockpile planning is presented. This process supports proactive mine planning to minimise unexpected fluctuations in the final product.

Jan 1, 2005

Routine, in-pit geological mapping of highwall at Central Queensland Coal Associates (C.O.C.A.) deep strip mines has proved too slow for the increasingly greater highwall lengths which require mapping. This realiz- ation has encouraged the search for faster mapping methods and after trial of ground photographic methods has resulted in the adoption of interpretive mapping off stereo cover, oblique -- aerial photography. This entails using a Cessna 182 light aircraft flying at its slowest speed, the aerial meth- od finally employed consisting of two Vinten, air reconnaissance cameras mounted in parallel and simultaneously taking both colour and black and white photographs of the mine high- wall. The respective 1:500 scale enlargements produced from the 70mm format films combine to present the sharpest resolution attainable under the field conditions pertaining and such information on weathered material as only colour photography can fully render. Total costs for the aerial photography method are estimated to be about the same as those for conventional in-pit mapping. Whilst total costs are comparable, geo- logist's time for mapping a 10 km. length is reduced to less than half that for in-pit mapping (for Stage 1, fully accurate mapping) and accuracy and detail are greatly improved. A permanent, accurate record of overburden

Jan 1, 1981

By R Engle, R P. McMahan, D A. Bowman, S Schafrik, W Thabet

Preventing injuries and fatalities related to conveyor system use in the mining industry is important and increases uptime while decreasing lost time. The research presented here is funded by the National Institute for Occupational Safety and Health (NIOSH), and intended to accomplish this prevention by the use virtual environments (VEs) to improve training and help miners better understand the hazards of working around conveyor systems. Two conveyor system VEs designed to teach miners about hazards and to safely complete tasks around conveyor systems were developed for this project. The first conveyor system VE, called the instructional tour, gives the miner a semi-automated tour of a conveyor system and teaches the miner about possible hazards (eg, missing guarding) and how to safely fix conveyor problems (eg, a stuck idler) using lock-out, tag-out procedures. The second, called the virtual shift, allows the miner to freely navigate around a conveyor system to detect and avoid hazards. The miner is presented with equipment failures that need to be safely repaired during the virtual shift. If the miner fails to identify and avoid a hazard or fix a failure in a safe manner, an animation of the consequences is shown to the miner, who must start the virtual shift over. The models for the conveyor system VEs were created using 3DS Max. Desktop versions of the VEs were then created using Deep CreatorÖ, an authoring application for creating interactive 3D environments. Later, more realistic versions of the VEs were created for CAVEÖ, a room-sized visualisation system, using DIVERSE, an application programming interface. In initial evaluations of the conveyor system VEs, mining colleagues have indicated great interest in such training tools. According to their feedback, these and similar VEs would provide excellent alternatives to normal classroom training and serve as positive precursors to hands-on experience. These VEs provide new miners a chance to experience hazards associated with working around conveyor systems without being in possible danger.

Jan 1, 2008

When the writer first saw the square-set timbering, he was at once impressed with the fact that the frames made by the sets, along the lode amI across it, were composed of panels with rectangular openings, and it was puzzling to understand howsuch a collapsible construction could resist pressure that came unevenly on it. Later he learnt that the sets did not satisfactorily resist such pressure, but mullock filling had, to a great extent, to undertake this duty for them. So it appeared that the setswere practically an expensive scaffolding, enabling the miners to work in the face and carry the stope forward, till the filling was put in behind them to take the pressure of the roof and sides of the excavation. Of course some of the pressure is takenby the sets, but this is because the set timbers prevent the filling being done perfectly; if it were practicable to remove the sets before filling, the filling by itself would more effectively support the back and wall, than do the combined sets andmullock. On the whole, therefore, the sets can hardly be said to be of much benefit where pressure has to be resisted. Despite this, the system has been of immense service in mining wide lodes, but for all that, it can only be pronounced a makeshift.This is no reflection on Deidesheimer, the famous originator of the square set, for, as will be shown later on, this way of...

Jan 1, 1911

By Sullivan T. D, Lohe E. M

Geological structure is one of the main controls on ground conditions within mining. It has a significant impact on the mining conditions and productivity of coal mines within the Sydney - Bowen Basin. The three main types of faults common to this region, normal, reverse and strike-slip systems, each present distinct challenges to mining. These systems effect a wide range of geotechnical and mining conditions within the mines. These include coal quality, strata stability, goat and caving behaviour, productivity and maintenance schedules of mining equipment, mine design and mine-site stress fields. A better understanding of the regional, local and mine-scale structural setting, timing relationships of structural events and the mechanisms of fault formation will greatly aid industry's push for greater productivity and competitiveness.

Jan 1, 1991

The Bureau of Mines, with a history of mining research since 1910, still seeks improvement in safety and health along with improvement and competitiveness in the mining industry. Much promise of such improvements lies in new technology, and this is particularly the case in the still growing coal mine sector, although much Bureau research is long term, high risk, aimed at new concepts.The miner's environment is a primary concern, involving technologies of contaminant monitoring and control in high production scenarios. Contaminants arising from diesel use, alternatives to high speed rotary cutting and more efficient dust removal are being addressed, and drilling efficiencies, better monitoring through unitising operations and insitu rock dust monitoring are particular features.

Jan 1, 1991

By Watson K, Pollard D. M

The electrolytic recovery of metals from solution requires an understanding of the characteristics of the particular system employed, and the current efficiency and morphology of the deposit are influenced by such factors as cell design, metal ion and supporting ion concentration, acid concentration, temperature, impurity levels and cell design. The electrolytic deposition of both cadmium and silver present individual difficulties, and special cell designs are used for each of these metals. It was found that cadmium deposition was plate-like at lower cadmium concentrations, and at higher current densities. The presence of zinc in the electrolyte promoted nodular growth. Current efficiency remained high even at 50C in contrast to published information. Silver deposition morphology was relatively unaffected by changes in silver concentration, pH and current density. Current efficiency was reduced as temperature was increased.

Jan 1, 1989

Risk Management has been applied relatively slowly in the mining industry. Except for the risk concept application in financial considerations, the application of Risk Management in safety management has been far from satisfactory. When applied it was treated in a global occupational safety and health sense. Regardless of how much the mining industry has progressed over the years it is still, in many respects, `state-of-the-art' business. The safety aspects of mining are well known and yet little understood by the public. Regardless of what has been achieved so far and how much effort has been put into it, mining is regarded as an unsafe and somehow rude business. Safety records of the mining industry vary from State-to-State. Latest mining related disasters in PNG and Queensland and some other fatal accidents support this public perception. They purport a need for change in managing safety in the mining industry. The latest mining fatalities have raised the issue: What must be done to improve safety standards? Duty of care, risk management and system engineering concepts can provide some answers. Risk Management principles which have been advocated for some time provide many answers and explanations and can make safety management more constructive and workable. What has been missing so far is that this concept has neither been applied nor has been modified for its practical application and purpose on a larger scale. A risk management approach to the management of safety and health in the mining industry is addressed, herein. This approach does not attempt to provide the solution. It does, however, provide a basic understanding of what Risk and Risk Management are all about. Rational management of risk is addressed in the life cycle and system contexts. A system of continuous improvement is applied. There is always a chain of events, outcome, exposure, consequence(s), and consequence(s) value(s). It means that development of an event takes place in time and space. Dynamic circumstances have been created in or within the system. It is a decision-making process designed to provide a methodology which is directed not toward a mathematical model but toward easy use and application in dynamic working environment, by decision-makers who can be anybody from either a risk taker or a risk creator. The emphasis is placed not only on arriving at the best practical, possible and fair decision but also on structured and systematic acquisition of knowledge about the system, its hazards and associated risks, hence increasing the decision maker's ability to manage the decision-making process related to the management of risk.

Jan 1, 1995

The problems arising in the excavation of hard rocks with the use of mechanical tools consist chiefly in a slow advance rate accompanied by an intensive wear due to the toughness and abrasiveness of the rock. In order to allow the further extension of mechanical excavation beyond the limits of the presently available technology, the assistance of waterjet aiming at improving the performance of the equipment while reducing the wear rate of the tools, has been recognised as one of the most interesting technical solutions. The paper illustrates the improvement of the performance of both disk cutters and picks obtained with the waterjet assistance at the Waterjet Laboratory of the University of Cagliari on a medium-hard rock.

Dec 6, 2010

Jan 1, 2004

By Mark C

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become.more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width- to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By Taylor GP

Mining Lease SML 57 was registered to Mount Kasi on 5 January, 1995. The Mount Kasi gold mine is located in Vanua Levu, Fiji's second largest island and operated from 1932 to 1946 producing 261,000t of ore at an average grade of 7.5g/t Au. The deposit represents a structurally controlled style of high sulphidation copper gold mineralisation with peripheral low sulphidation mesothermal vein type gold mineralisation. The resource consists of 1,048,000 tonnes of residual soils (eluvium) containing 1.9 g/t Au at 0.5 g/t Au cut off and 1,240,000 tonnes of hard rock at 3.0 g/t Au and 1.0 g/t Au cut. 94 drill holes, 298 auger holes and 85 pits were modelled to outline the resource. 29% of the pits bottomed in mineralisation and it is likely the full thickness of eluvium has been understated. The pit is scheduled to produce 500,000 tonnes of ore per annum to yield 35,000 ounces of gold with an initial 2 years of eluvial ore followed by a further 2 years of hard rock ore. Total capital costs are estimated to be less than 10.0 million dollars with construction planned to commence in 1995. The likelihood of locating further ore is high.

Jan 1, 1995

In the future to excavate sufficient coal for power generation, two dredgers would be required to dig overburden or interseam 70010 of the time and three dredgers 40010 of the time. One overburden system was not adequate for this requirement, making coal production reliability vulnerable. TS5 spreader is the new machine element of this system. The selection of the best type of machine configuration to suit the application was then subject to an internal SECV VE Study, a registration of interest and a tender for two machine alternatives. This paper outlines the reasons why SECV planned the Secondary Overburden System and how the Krupp machine met these requirements. It also identifies the main design features of the machine and its constructability which will allow the machine to be operational by the end of May, 1990.

Jan 1, 1989

Geostatistical conditional simulation is a method to assess variability and risk in mineral deposits and the tool has wide potential applications in the iron ore industry. Correct reproduction of multivariate relationships is important in iron ore simulation, especially between Fe and impurities such as Al2O3, SiO2 and P. The turning bands simulation method, using a full model of coregionalisation for multiple attributes, is the main multivariate conditional simulation algorithm used in the Western Australian iron ore industry. This paper discusses the results of a more recent approach using minimum/maximum autocorrelation factors (MAF) to transform and decorrelate the multivariate data prior to independent sequential Gaussian simulation (SGS). MAF-SGS results are compared to those of the turning bands approach in the Yandicoogina channel iron ore deposit (CID), and both methods performed well in simulating Fe, SiO2, Al2O3 and P distributions. Extensive checking of simulations showed that both approaches could reproduce multivariate statistics and spatial continuity of the original conditioning data. Both approaches reproduced the histograms and variography of input sample composites. While the MAF-SGS approach requires additional transformations when compared with the single normal scores transformation required for the turning bands method, MAF requires only that the direct semivariograms be modelled. In contrast, using turning bands with multiple attributes requires modelling a full linear model of coregionalisation, which can be difficult to model because of the need to ensure the model is positive semi-definite. Turning bands may be preferred if there are a modest number of correlated variables allowing construction of a linear model of coregionalisation that adequately models the multivariate behaviour. MAF-SGS is preferable for larger numbers of correlated variables. Both MAF-SGS and turning bands methods performed well in conditional simulation of correlated variables at Yandicoogina.

Jan 1, 2007

By R Vleggaar

In addressing a short-term operational need for the relocation of a tailings storage facility reclaim pond, a mine has achieved a host of water management objectives. Through effective planning and adoption of a strategic æwhole of mine lifeÆ approach, the mine has achieved significant environmental, social and economic benefits. A review of all water management aspects across the site identified a host of other interrelated water issues and concerns which, if dealt with individually, would prove too costly for individual operational departments. When considered as a whole, however, the issues became opportunities and provided the stimulus for integration of the site water management system. The development of site water and solute balance models provided the tool by which a number of water management options/strategies could be evaluated. The conceptual design and costing of the proposed water infrastructure further facilitated the evaluation of the multiple benefits to be gained from each option. A business case could then be made to mine management for the preferred option. The recommended water management strategy finally recommended to the mine not only provided a tailings storage facility (TSF) reclaim pond, but also provided for:increased wastewater recovery from the TSF, the capture of all waste rock dump run-off, additional water harvesting from local creeks, increased wastewater reuse, improved environmental water management, infrastructure that could be used by the local community after mine closure, and overall cost savings. This paper illustrates how effective water management planning can provide both short-term economic and environmental benefits, as well as long-term social benefits.

Jan 1, 2006

By Mercer JK

This paper gives a description of the research undertaken by an explosives manufacturer to give better technical advice to the Mineral Industry. Blasting Physics is defined as giving a systematic and coherent account of the initiation and subsequent effects of high explosives upon the surrounding medium. As a result of this work a mathematical model based on the gener- ally accepted mechanism of blasting has been developed. The mechanism and the resulting model are briefly outlined. IFrom'this model the effects of burden, spacing, blasthole diameter, rock and explosive properties upon fragmentation and heave can be calculated. Using these calculations it is then possible to see how variations in frag Imentation and heave can affect the overall production costs of a mine whether it is surface or underground. The overall costs are made up of a number of individual costs - drilling, blasting, loading, hauling and crushing. ach of these operations influences or is influenced by fragmentation and heave s these costs are inter-related, the

Jan 1, 1975

By J Slade, R Trueman

Unplanned dilution has the potential to seriously undermine the economic viability of a mine, and in some cases results in mine closure. The effect of stress damage on dilution has become increasingly relevant as mining depths increase. In the case of narrow vein mining, the incremental extraction of long-hole rings has the potential to result in a moving high stressed zone at the stope brow. This leads the hanging wall and footwall to experience a spike in the stress to strength ratios as the brow passes. In some cases, the stress to strength ratio may be high enough to result in fracturing or damage to the rock mass. The aim of the study described in this paper was to investigate whether stress damage results in a significant increase in dilution. The study involved analysis of overbreak from 410 case studies from the Kundana Gold mine in Western Australia. Site personnel had already undertaken calibration studies of the stress levels that result in rock mass damage. This calibration, in conjunction with numerical modelling showed that stress damaged stope walls at this mine had on average 50 per cent more overbreak than stope walls where stresses had not exceeded the damage criterion. For a design mining width of 1.5 metres, and with both walls impacted, this represents 36 per cent increase in dilution. After adjustment for possible sources of bias the difference reduced to an average 0.10 metres per stope wall, representing 13 per cent dilution for the mining width under consideration. The potential for stress damage related overbreak should therefore be considered as part of any assessment of narrow vein dilution.

Jan 1, 2005

By G Harbort, T Georgiev, M Phillips

Phu Bia Mining Ltd, a subsidiary of Pan Australian Resources Ltd owns and operates the Phu Kham copper concentrator located in the Xaysomboun District, Lao PeopleÆs Democratic Republic. Construction and commissioning of the 12 Mt/a copper concentrator and associated facilities was undertaken by Ausenco Ltd and handed over to Phu Bia Mining Ltd in April, 2008. The first copper concentrate was produced in April 2008 and the ship carrying the first shipment of copper concentrate set sail 27 July 2008. Nameplate mill throughput was reached in August, 2008 when 1 020 000 dmt of ore was treated in the milling and flotation circuit. The Cu-Au mineralisation is contained in skarn and stockwork mineralisation and is interpreted as a distal expression of a conventional porphyry copper-gold system. Copper mineralisation is principally in the form of chalcopyrite with lesser bornite. Gold occurs as small grains, typically associated with copper minerals. In the upper portions of the orebody, oxidation and water table movements have resulted in near surface leaching of the copper and below the leached zone, supergene enrichment resulted in chalcocite mineralisation. The circuit operates with a semi-autogenous grinding (SAG) û ball mill circuit, feeding a bank of OK200 rougher cells. Rougher concentrate is reground in an IsaMill prior to entering a cleaner circuit consisting of three stages of cleaning and one stage of cleaner scavenging. The concentrate typically assaying 24 per cent Cu and 6 - 7 g/t Au is hauled for over 1000 km across the border to the Port of Sriracha in Thailand, and stocked in sheds at the wharf from which it is shipped to various Asian smelters. This paper discusses the successful commissioning and ramp up to design tonnage and metallurgical performance. In addition, a program to optimise both the comminution and flotation circuit is detailed with reference to grinding efficiency, flotation residence time and size by size mineral recovery.

Jan 1, 2009

By Bolton G. C

Experiments were conducted to access the feasibility of removing zinc from lead slag by sulfation or chlorination or both. Gaseous sulfation with sulfur dioxide and oxygen released only 50 per cent of zinc even under the most severe conditions. Sulfation with concentrated sulfuric acid by a fast-leach process released 95 per cent of zinc while pug-roasting released a maximum of 78 per cent of zinc. Chloridization with NaCi in the presence of sulfating gas released 50 per cent of zinc, while direct chlorination with chlorine gas and oxygen released 85 per cent of zinc and 100 per cent of lead in a chloride condensate containing little impurities.

Jan 1, 1980