Search Documents

By Walker G. S

Infrared and Raman spectroscopy have been used to study a range of solid state and aqueous solution species which are of interest in extractive metallurgy. In the solid state new Cu(II)/CN'/NH3 complexes have been detected, iron impurities in kaolin characterised, aluminium substitution in hematite and goethite quantified, and the crystallinity and orientation of zircon determined in heterogeneous crystals. In aqueous solution metal cyanide complexes and equilibria were readily characterised, the thermal decomposition of SO2 monitored and products identified, and complexation of AI(III) by hydroxycarboxylates observed. Attempts to monitor the early stages of the gelling of silicate solutions were less successful, with only changes in the gel being detected. However, the degradation of 12-tungstosilicic acid was readily monitored as a function of both time and pH.

Jan 1, 1996

By Scott A

The object of most blasting operations is to destroy the insitu structure of the rock mass so that mechanical equipment can efficiently excavate the rock fragments. In achieving this objective the blasting engineer is also concerned with minimising damage to the adjacent rock which forms the mine structure relied upon to provide support. Damage to this "structural" rock is undesirable but usually occurs as a result of two distinct processes: ò readjustment of stresses around the excavation as a result of the mining process itself ò impact of vibration and high pressure gases from blasting operations. Gross damage to mine structures from either cause is observed as visible alteration to the appearance of the rock structure in the form of cracking, slabbing, back or over break and visible displacement. Recent work at the Julius Kruttschnitt Mineral Research Centre (JKMRC) has shown that significant reduction in the strength of a rock mass can take place well before the onset of these obvious signs of damage. It has been demonstrated that the effect of blast damage on the behaviour of the rock mass can be many times more prominent than the effect of stress redistribution. This offers the blast design engineer the opportunity to significantly reduce blast induced damage to rock structure by modifying blasting practices. This paper introduces the current JKMRC postgraduate research projects investigating the evaluation and control of blast damage.

Jan 1, 1990

By Evans A. F

Arising out of the increasing demands for efficiency in modern ore-dressing operations has grown a requirement for fuller knowledge of the characteristics of the ore treated. In part, this is being met by improved methods of study of the mode of occurrence of the constituent minerals, and of the intricacies of their physical relationships.A typical instance of the need for such a study is the presence of some undesired mineral in a flotation concentrate or tailing, which may be due either to mechanical association through insufficient grinding, or to incomplete separation in the flotation operation.Again, with modern practice in fine grinding, which often requires that from 70% upwards of the ground ore shall pass a 200-mesh screen, it is obviously impossible to obtain data on comparative grinding efficiencies, for instance, unless there is adequate knowledge of the size-composition of the material passing the finest available screen.Studies like these can be made satisfactorily only after size-separation (which may be carried out conveniently by elutriation) and by actual visual examination with the aid of a microscope, and the minute size of the mineral grains to be examined has necessitated the development of a new technique of sizing and microscopic examination.

Jan 1, 1932

By Guarascio M, Massacci P

In process simulation, more reliable prediction of industrial results and evaluation of data for design purposes and process optimisation may be attained by the combined use of: the modelling and simulation of ore characteristics, and 2. the modelling and simulation of the process. It is well known that geostatistical methods allow the defining of models of orebodies in which the variables considered are the grades of the valuable components. These models are proper for reserve estimation, geostatistical contouring, design and simulation of the exploitation method, and, in addition, for evaluating the variability of the ROM which is expected to be fed to the processing plant. However, no data are normally incorporated in the orebody model in order to evaluate the ore characteristics relevant for a reliable process simulation. The procedure for process simulation aimed at predicting plant results normally used so far consists in collecting samples from different orebody sites and building up a so-called 'representative sample'. On this sample, the ore characteristics (eg liberation, washability, grindability, etc) and the processing tests are referred to as the 'average behaviour in the orebody', assumed constant. A more reliable methodology consists in collecting samples from different orebody sites, in performing tests to characterise the samples from the point of view of the process (ore patterns), and in using synthetic parameters (process features). The values of the parameters are processed using geostatistical methods in order to develop a model for simulating the feed to the process. The estimation may thus be referred to the amount of recoverable minerals instead of to the existing minerals. Furthermore, the selection of the processes, the sizing of equipment and the design of control devices, as well as the prediction of results, become more accurate and reliable.

Jan 1, 1993

The extraction of the values from gold bearing clay or clayey ores has always presented difficulties. A description of the successful operation of a mill working on material of this nature is here given in the hope that it will be of interest to mining engineers and metallurgists, particularly as the ore body referred to has been worked out. The methods finally adopted were evolved at the mill after the failure of 3: plant specially designed in England and sent out to New Guinea to cope with the clay by the old principle of calcining to brick followed by crushing and cyanidation. A description is given of the direct cyanidation of run of mine ore in '90 ton vats; which was finally adopted after a great deal of study and experiment. Mention is also made of the method of removing overburden in the open cut and the mining and transport of the ore from the open cut to the mill. The purpose of the paper is to record these matters while the information is still available. . .DESCRIPTION OF THE ORE BODYThe values occurred in a flat-lying lode which had slipped about half a mile down the mountain side and had come to rest in the nearly horizontal position in which it was found and worked. The thickness of the deposit varied from a maximum of about 25 ft. at the northern end to about 10 ft. at the southern end. The ore body was capped with an overburden of decomposed breccia and porphyry of variable thickness the maximum being about 65 ft. The underlying rock, or the footwaIJ of .the flat ore body was breccia locallyknown as blue breccia.

Jan 1, 1951

By Hunter TC

Metals Refining Operations Pty. Ltd. (NMO), PNG's only gold and silver refinery is operated by Golden West Refining Corporation Ltd (GWR), a member of the Rothschilds group and has a strong PNG ownership link through statutory shareholders. Located in Waigani, MRO has been successful in substantially increasing production through toll refining for Porgera, Misima, Tolukuma, Wapolu and, more recently, at Lihir as well as treatment of alluvial gold from smaller operations. This increased throughput has resulted in the need to constantly upgrade equipment, techniques and practices, particularly to continue quality improvements and meet market demands. The evolution of these changes are documented and discussed and the probable future development plans are detailed.

Jan 1, 1997

By Quast K. B

The ore used in this test program was a composite sample from Waihi, New Zealand containing 2.7 g/t gold and 36 g/t silver. From the testwork it was found that a high concentration of sodium cyanide (0.1 per cent) was necessary to ensure a high recovery of both gold and silver. There appeared little chance for either differential leaching or adsorption of gold and silver. The addition of bentonite clay decreased the rates of gold and silver dissolution. The addition of 50 g/1 NaCI had little influence on the rate of silver extraction. The addition of 5 g/l carbon gave adsorptions of 70 per cent of the gold and 35 per cent of the silver, indicating the possible presence of base metal cyanides in solution. The addition of excess sodium sulphide only precipitated 70 per cent of the silver in solution, adding further evidence to the presence of base metal sulphides. The production of separate silver and gold products was not possible by either preferential leaching, preferential adsorption of gold on carbon or preferential precipitation of silver.

Jan 1, 1991

While, in the past, a great deal of attention has been focussed on technical issues and the performance of explosives in rock, the explosive user, an essential link in the chain, has often been neglected. In the mining industry, too often, the benefits of excellent technical work have been degraded over time due to the lack of definitive and documented control. Using the principles of quality management a quality training system was developed and implemented for management of explosives use at Gunpowder Copper Ltd (GCL). This paper describes the structure of the system, its development and implementation, and contains practical advice and information for managers responsible for blasting and charge crews. The paper is in four parts: I Quality systems. A brief overview of the relevant aspects of total quality management that apply to explosives use. The requirements for documentation, management and auditing are explored. 2. Training for competency. The five essential elements of Competency Board Training (CBT) are examined, including auditing. 3. The Gunpowder Copper system. Implementation of the complete training system. Documentation and its control, auditing, instructions for operators, management responsibility and means of obtaining operator ownership are amongst the issues raised. Reporting requirements are the means to effectively manage change are described. 4. Summary. The paper concludes with the tangible benefits seen by Gunpowder Copper through the adoption of a quality training System.

Jan 1, 1995

By Gibson I, Somerville J

Three main confined aquifers occur in interseam sediments beneath the planned excavation for the Loy Yang Brown Coal Open Cut. Sub-artesian groundwater pressures occur in all aquifers necessitating dewatering to prevent excessive seepage and depressurisation to prevent heaving of the open cut floor and batter instability. Reduction of water pressures in coal joints is also required to maintain coal face stability. This paper describes the depressurization and dewatering strategies, investigation for and installation of pump bores and groundwater observation bores. Approximately 5000m of drilling is carried out annually for dewatering at Loy Yang and both cable tool and rotary flush drilling methods are utilized. The cabletool method is used to obtain accurate samples for laboratory analysis, whereas rotary flush methods are used for speed and for installation of the larger diameter pumping bores. A method of re-establishing pump bores after partial excavation during mine development has been successfully developed with large cost savings. Trials are also being conducted with pre-collaring of deep bores with rotary methods then sampling the aquifer strata with a cable tool rig.

Jan 1, 1988

By Hargraves A. J

At 4 MPa gas pres ure and 30°C the sorptive capacity of 10 selected Australian dried coal ranges from 17 to 23 m3/tonne of CH4 and 27 to 36 m3/tonne of CO2. Values for moist coals are about 25 per cent less. At 20°C, sorptive capacities are about 18 per cent greater. No clear relationship between coal rank and sorptive capacity was established.The permeability of coal to gas is dramatically reduced by progressive hydrostatic confinement. No single 'permeability' for a coal can be established because of relative affinities of coals and the gases (Ar, CH4 and CO2) used in experiments. Bedding plane permeability is significantly greater than permeability normal to bedding. Dependent on gas/coal combinations, permeabilities without confinement ranged from 150 to 0.05 millidarcies, and with 8 MPa hydrostatic confinement from 1.0 to 0.001 md. Generally, permeability is increased by reduction in temperature, and reduced by increase in moisture as one changes from Ar through CH4 to CO2. In retrospect, it is preferable to ubject permeability sample to 8 MPa hydrostatic stress only once, because changes occur in the samples and it is difficult to use other gases successively.The initial rate of desorption, DP, does not appear to be a reliable index of proneness to instantaneou outbursts for Australian coals.The methods used for determining quantitative gas-coal properties appear suitable and reliable for testing other coals.

Jan 1, 1985

By M Dorricott

This paper describes the design, construction and performance of sill pillars using cemented development mullock at the Crusader Gold Mine. The orebody is some 35 m - 60 m in length, 5 m - 8 m wide, dipping at 60¦ - 85¦ and plunging at about 40¦ to the north. It is accessed via a footwall decline. The ore occurs at the contact between basalt and ultramafic. This contact is characterised by shearing and alteration; and is prone to unraveling failure. The cut and fill mining method at Crusader extracts 25 m high ore blocks in four flat back lifts and one 8 m thick crown pillar. To enable full recovery of these high-grade crown pillars with minimal dilution, a 5 m thick sill pillar is constructed using cemented rock fill (CRF), after mining of the bottom two lifts in each block. Uncemented development mullock is used as rock fill (RF) for subsequent lifts. Development mullock and cement/water slurry is mixed underground to produce CRF. The fill is transported to the stope in LHDs and dumped on the floor. The sill pillar is advanced progressively, with compaction provided by the loader driving over the previously placed fill. Old jumbo rods are installed as shear pins along the flat dipping hangingwall to reduce the risk of rotational failure of the pillar. A fan of cable bolts is installed into the hangingwall to prevent unraveling failure in the sheared ground. Buffer blasting is used to minimise damage to the CRF sill pillar when the crown pillar below is extracted. At the time of writing, extraction of the crown pillar underneath the CRF has taken place at the 930 stope. The crown pillar was extracted successfully with dilution from the backfill and hangingwall minimised and 98 per cent of the gold recovered. This compares with pillars that were mined beneath uncemented backfill where only 70 per cent of the gold was recovered and where there was significant dilution from the backfill and from hangingwall failures. Where no CRF was placed, there were also numerous production delays caused by large rocks from the hangingwall blocking the stope brow.

Jan 1, 2002

By K Heiskanen, R A. Grau

Gas velocity (Jg) measurements conducted close to the froth-pulp interface over the cross-section of a flotation cell reveal how efficiently the incoming air is being dispersed throughout the volume of the cell. Furthermore, measurements of Jg at deepest locations in the cell provide valuable information about air recirculation and dispersion conditions in the bulk volume of the cell. Gas velocity in flotation cells has predominantly been measured by a transient capture of gas in a graduated probe. In this project, a new sensor for measuring gas velocity in an on-line manner was developed. A probe is partially immersed in the flotation machine, below the froth-liquid interface. The probe is used to collect the rising air bubbles from the liquid phase. The liquid-froth interface is shifted into the probe under vacuum. A controlled vacuum is kept inside the probe. As air bubbles burst inside the probe, the excess of air is continuously removed from the probe via suction. The removed air is measured using a mass flow meter. The fully automated sensor allows us to continuously measure Jg at different location in a flotation machine. An experimental programme was carried out in a 10 cm diameter laboratory flotation column to determine the accuracy and repeatability of the automated sensor. The new sensor was used for evaluating gas dispersion conditions in a 215 litre transparent laboratory scale flotation cell. Gas velocity distributions along the radial and axial directions of the cell were measured over a wide range of operating conditions. The operating conditions in the cell were modified by altering impeller speed and air flow rate. Two different rotor-stator mechanisms were utilised to disperse the air in the cell, the MultiMix and the FreeFlow mechanism. In this paper, a description of the gas velocity sensor is given, and the results of the experimental work are discussed in detail.

Jan 1, 2005

By A Cooper

The current financial climate has given rise to fears that falling mineral prices and tight credit will force mining companies to cut back on production and new project development in a bid to cut costs and conserve cash. However, a prolonged squeeze on global supply can have only one result: a massive and potentially explosive demand for metals in the not-too-distant future. A resurgent global economy will also generate dramatic new demand for oil and energy, with a return to higher oil prices likely. How then should the mining industry plan for the future? In-pit crushing and conveying (IPCC) could lead the way as a partial or complete substitute for trucks. In 13 of 15 studies undertaken by Sandvik and Snowden, comparing IPCC with truck-optimised pit designs, IPCC generated operating savings ranging from US$0.18 to US$0.82 per tonne moved, compared to trucks. Trucks have higher operating, maintenance and energy costs than conveyors. New emission standards on diesel engines may make them more emission friendly but less efficient in terms of energy usage. With far more efficient energy use and cheaper operating costs per tonne moved than trucks, conveying offers an attractive alternative for the bad times ahead and into the apparent energy depleted future. When evaluating alternatives, a reasonable first step would be to conduct a scoping level study which analyses the differences in capital and operating costs between a truck and shovel operation and an IPCC solution. The study can also determine what type of IPCC is best suited to the particular mining application. The results can then be used to decide whether a more detailed study is justifiable. IPCC is a proven process that, with a fresh mindset, can make a significant improvement to mining operations. Sandvik (as an OEM with a full suite of IPCC equipment) can undertake these studies in ten working days in conjunction with Snowden or any other independent mine planner who knows how to schedule for IPCC. Because most mining industry personnel have been æborn and bredÆ on trucks and shovels û this paper focuses on some of the practical considerations necessary to make IPCC systems work that the Sandvik Technical Services Group has encountered during these studies.

Jan 1, 2009

By Daxian Z, Youdi Z, Shucai Y

The Huolinhe surface mine is a very large-scale surface coal mine, located in the north-east area of China with a production rate of 1.2 Mtpa. Its coal haulage system has a large capacity, long transportation line and high degree of automation. The system comprises two crushing plants, many belt conveyors, four surge bunkers, one loading bunker, one coal storage and five end product bunkers. In this paper, the network patterns of semi-continuous systems in surface mines are studied, the reliability calculation methods and a simulation model are established and the software for computing the reliability of a semi-continuous system is worked out. By considering the whole coal haulage system in the Huolinhe surface mine, the authors developed the system reliability-numerical simulation method. The steps and the computing results of this method are described in detail. Through the calculation, we can master the present situation of system reliability and the main factors impairing system reliability, expose the system weak links, put forward the ways of enhancing system reliability and furnish the basis for improving the system and equipment. The way of increasing capacity and methods of enhancing system reliability are further raised.

Jan 1, 1995

When a thin film of volatile matter is deposited under vacuum on a polished coal surface, and the coated surface is examined microscopically in piano--polarized reflected light, colour changes are observed characteristic of the various macerals present. The colour changes appear to be mainly due to interference between light reflected at the upper surface of the film and at the film/coal interface. A variety of source materials for the volatile matter required have been tested, including powdered bituminous coal, coal tars, boron oxide, and certain resins.

Jan 1, 1969

By D A. Kepert, D Clark

During early 2004, Fortescue Metals Group (FMG) began an aggressive exploration and drilling program in the Chichester Range, targeting iron enrichment developed in the Nammuldi Member at the base of the Marra Mamba Iron Formation. The timely recognition by FMG of distinct zones of (hypogene) microplaty hematite (mplH) enrichment overprinted by extensive supergene mineralisation led to an early reappraisal of the geological history of the area and characterisation of the possible structural and stratigraphic controls on mineralisation. Regionally, the Chichester Range dips gently at less than 5¦ to the south, however, detailed mapping shows that this regional limb is overprinted by low amplitude, long wavelength, north/south to northeast/southwest trending folds. The locations of major structures in the Marra Mamba Iron Formation, combined with spectral analysis of known mineralisation, allowed extrapolation and prioritisation of exploration target areas. The delineation under cover and understanding of these structures was enhanced by detailed airborne magnetic data. Recognition that supergene mineralisation was associated with a palaeotopography that continued significantly under cover to the south under sediments of the Fortescue River valley led to the discovery of extensive supergene mineralisation together with additional mplH mineralisation. A model for the landscape evolution and preservation of enriched Nammuldi Member was generated in order to help communicate both the complexities involved with targeting drill holes beneath cover and the potential limits to the lateral extents of mineralisation.

Jan 1, 2005

By Denby B, Miles N. J

The underlying theory behind the construction of an on-line size analysis system is described together with an introduction to the Artificial Intelligent techniques that it is founded on. Previous systems based on more traditional technology such as edge detection and dilation algorithms have been restricted by the significant processing power they require, this has resulted in the production of systems with either reduced functionality or severe hardware requirements. A neural network approach offered a new perspective to the problem of size analysis; the ability of a network to learn and recognise subtle patterns in training data before on-line processing is initiated opened up the possibility for the production of a fully functioning practical system. The format of the training data had to be carefully analysed prior to its implementation in a neural network as the capability of a neural network solution depends as much upon a suitable data preparation as it does on the system architecture. To facilitate experimentation with various profile quantification techniques such as fourier and fractal analysis an Image Profile Analysis System was constructed (IPAS) in software on a personal computer. The IPAS system was produced with the aim of pre-processing image data to create data sets for experimenting with external neural network packages. The system allows the analysis of both real images obtained by image capture and simulated images created by an in-built in simulator. A measurement comparison scheme is also included together with a case study concerned with the frequency analysis of simulated images. The power of neural networks combined with the data compression provided by profiling removes the need for direct measurement of individual particles. This has obvious implications on the level of hardware necessary, and ultimately the expense of a stand alone system. The extrusive nature of data collection via an image analysis system will also permit simple installation of a shipped system; eliminating any requirement for interference with existing machinery.

Jan 1, 1995

In the introduction to a recent paper dealing with, the relationships of magnetite and hematite in the banded iron formations or "jasper bars" of the Western Australian pre-Cambrian(17)t the author made a brief mention of these interesting rocks, of the principal series in which they occur and of a few of the rock and mineral types to be found within them.He drew attention to the essential shnilarity of these Western Australian banded iron formations to those of the pre-Cambrian of such other countries as the United States Lake Superior region, Sweden, South Russia, India, South Africa and Brazil, and gave a brief summary of his views as to the origin of the formations in Western Australia. Furthermore he stated that the banded iron formations have proved of considerable direct economic importance in the goldfields and other' regions of Western Australia, and he referred to the assistance they have provided the field geologist in geological mapping and the determination of geological structures.It is in elaboration of this last statement that the present paper has been written. In the following pages will be found some examples of the use to which the jasper bars have been put in the determination of the geological structure of critical areas in the goldfields of the State.Firstly, however, it may be as well to recapitulate the features of interest in these rocks. The true jasper bars or banded iron formations including the types jaspilite, banded hematite quartzite and banded magnetite quartzite or chert, together with their higher grade metamorphic derivatives such as banded magnetite-gruneri~ quartzites, magnetitegrunerite schists, fayalite ,and hedenbergite bearing handed magnetitegrunerite quartz rocks and' to 'a lesser extent magnetite-hypersthene grunerite quartz rocks, are abundant in the older series of the Western Australian pre-Cambrian. They are best developed in the older Greenstone or Kalgoorlie series of the goldfields districts, interbedded with metamorphosed basic lavas, tuffs and sediments. The mineralogy andpetrology of these rocks, the history of their metamorphism and their origin have been discusseq elsewhere in some detail by the author(19), (20). In one of the papers(20) it was clearly demonstrated that in the light of the true facts the old silicified shear zone theory of the origin of the jasper bars is quite untenable and that the formations undoubtedly represent sedimentary horizons as was recently pointed out by McKinstry(14).It has also been shown that banded ferruginous cherts, quartzites and cherty carbonate rocks of much lower metamorphic grade are well developed...

Jan 1, 1943

Vaal Reefs Mine annually produces some 75 tonnes of gold. Stoping operations, using a scattered mining method, are conducted on several reef horizons within Witwatersrand Supergroup metasediments of the Klerksdorp Goldfield. Current grades average 7.19 g/t Au over a 133cm stoping width. The reef horizons, of which the Vaal Reef is the most important, consists of 2.9Ga palaeoplacer deposits at the base of low angle unconformities. Typically, a reef comprises a mature quartz and chert conglomerate with a siliceous matrix and intergranular pyrite and carbon. Geologists are primarily responsible for underground mapping and supervising of drilling programs. To a lesser extent they are involved with sampling, grade control, ore reserve estimation, mine planning and rock mechanics. Due to a general decline in grades of gold mines, an escalation of production costs, and with the current weak gold price, it has become essential to improve production efficiencies. Consequently the role of the mine geologist has moved away from that of simply keeping the mining people "on reef'. Greater emphasis is being placed on refining geological models to assist in selective mining of the reef and investigations of secondary reef horizons are encouraged. Exploration within fault losses and re-evaluation of pillars is important, and geologists are becoming more involved with sampling and grade control exercises.

Jan 1, 1990

Ventilation challenges are often encountered when an underground mine expands to new zones and it often is the case to make a thorough review of the existing system and assess immediate and future airflow needs at the desired quantity and quality. An unexpected mine plan change that calls for increased development and production from new areas can impose a strain on the existing ventilation system. Budgetary constraints can also demand creativity in design on the mine ventilation engineerÆs part. Since the addition of several mining horizons it had become obvious at the Meikle mine that something had to be done to increase airflow quantity and quality in the old main zones because most of the ventilation resources had been channelled for development in the new mining horizons. An airflow assessment of the existing system had to be performed and it was determined that the airflow quantity had to be increased by at least 30 per cent and the quality of the air had to be improved by reducing nuisance and respirable dust and at the same time reducing the airflow temperature before it was used in a few mining zones. At the conclusion of the airflow assessment it was determined that a third centrifugal fan would be installed on a new 3.05 m diameter borehole from surface to underground. By a careful study of temperature conditions over time it was determined that an evaporative cooling spray chamber would be sufficient to cool the airflow down from the high dry bulb temperatures observed down to saturation at the wet bulb temperature. At the same time excessive nuisance dust generated as a result of the airflow travelling a long way in a haulage drift will be knocked down in the spray chamber resulting in cool, clean air in the mining districts. Expansion of the existing surface ammonia refrigeration plant was out of the question for several reasons. The fact that the airflow was hot and dry meant that evaporative cooling spray chambers could achieve lower working temperatures at a very low cost compared to the expansion of the chilled water plant. The expansion of the ventilation system at Meikle mine and the use of evaporative cooling spray chambers were demonstrated to be very successful and the information presented in this paper can be of benefit to other mines experiencing the same ventilation problems as was the case at the Meikle mine.

Jan 1, 2005