Search Documents

By K Lee, K Fernando, S Rayner

Copper-gold ores have been technically difficult and uneconomical to process due to high consumptions of cyanide. Many copper oxide and sulphide minerals react with cyanide to form copper cyanide complexes, partly contributing to the high level of weak-acid dissociable cyanide in the tailings which is normally experienced during the processing of copper-gold ores. The cost for detoxification, if required for treating these tailings, would further inhibit the development of these copper-gold resources unless the cyanide used for leaching was recovered. Several technologies have been proposed to process copper-gold ores, aiming to recover copper as a co-product and cyanide for recycling in conjunction with the leaching process. A critical review of these processes reveals that a pre-concentration stage (solvent extraction or resin ion exchange) is required. Cyanide is recovered by the conventional Acidification-Volatilisation-Regeneration technique in most cases. A critical evaluation is also provided on technical aspects related to the use of Vitrokele Technology and a newly developed Elutech process in processing copper-gold ores, in particular with its application at May Day Mine.

Jan 1, 2000

By Barnett LJ

The Kellogg slag fuming model is extended to apply to the Port Pirie plant which uses recuperative heating of secondary air. Exten- sive investigations of plant operations pro- vide parameters for use with the model, and verification that the resulting model provides simulation which is very close to actual plant performance. The model is used to_deter- mine optimum slag fuming operating conditions, and the results of several other investigations with the model are briefly described.

Jan 1, 1975

The Committee for Mineral Reserves International Reporting Standards (CRIRSCO) was formed in 1994 to promote development and adoption of international standards for estimation and reporting of exploration results, mineral resources and mineral reserves. The CRIRSCO standards have been accepted by most mining companies and professional societies worldwide. Market regulators from Australia, South Africa and Canada require that these standards be followed when releasing public information. Among these requirements is the use of specific definitions for what constitutes exploration results, mineral resources and mineral reserves. If such information is publicly disclosed in must be estimated by a Competent or Qualified Person. In the United States of America, public disclosures are regulated by the US Securities and Exchange Commission. The SEC does not recognise the CRIRSCO guidelines, and some of the SEC requirements for public release of information are materially different from those applicable in other countries. The CRIRSCO definitions and the Competent Person requirements are reviewed and compared with those of the SEC. The organisation of the SEC and its rule making process are briefly discussed. Ongoing efforts to bring the US regulatory requirements closer to those applicable in other countries are presented, as well as other activities that CRIRSCO is entertaining with the United Nations, the International Accounting Standard Board and other international organisations to reach the objective of worldwide standardisation of reporting procedures.

Jan 1, 2006

Epithermal deposits have been defined as the lower temperature end of a spectrum of hydrothermal mineral deposits and are inferred to have formed near the EarthÆs surface. The preservation of an epithermal gold deposit in an Archaean craton is rather problematic, especially when such deposits form clusters or groups as reported for the Pilbara and Yilgarn cratons. For two of the better studied examples of epithermal gold deposits in these cratons, Becher and Wiluna, the evidence that they formed near the Earth surface is non-diagnostic, and the epithermal origin appears uncertain. Despite the simplicity of the original definition, there have been numerous errors in classifying epithermal gold deposits. It is suggested that these errors are primarily due to poor criteria defining the group as there is limited evidence of poor observational science being the cause. The criteria being used to recognise epithermal gold deposits include tectonic setting, ore element suite and quartz vein textures. None of these are diagnostic of epithermal deposits and their link back to the original low pressure-temperature definition of the class is tenuous. There has been definition creep over time as new observations on potential epithermal gold deposits become accommodated within a flexible definition. There is some urgency establishing and then using criteria to reliably identify epithermal deposits. Distinction of epithermal gold from weathered gold deposits is an important step. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By A Ruotsalainen

Mining industry sees a comprehensive future in optimisation and process control. High resource utilisation is a starting platform when lower operational costs with higher rate of return are the target. Simulation is quickly penetrating the mining industry as a planning tool. A discrete event simulation helps to visualise the reality of a mine and the various mining processes, which typically include a fair degree of complexity. What-if scenarios can help to determine the impact of occurring changes to production. Understanding of critical points in the layout and resource allocation at an early stage can help to optimise the material flow. The obtained information may then be used as proposal or confirmation of the system applicability and economy. Simulation is a way to fine-tune and optimise the resources within. It helps to predict system sensitivity to various aspects. Although simulation today is used typically in a feasibility stage, there is an opportunity to continue using simulation for further process enhancement. In the future simulation will without doubt be used increasingly as a dynamic simulation and continuous improvement tool. This paper discusses the use of OptimineÖ simulation tool in resource optimisation. Some examples describe the way the tool operates and how it helps to view the technology, mine layout and operational data.

Jan 1, 2003

By S C. Goel

The Obuasi Mine in Ghana, West Africa is the largest producing gold mine in Africa, outside South Africa. The mine has changed from a mine producing from narrow vein, high grade quartz orebodies to a mine producing from wide, lower grade sulphide rebodies. Traditionally mining methods were cut and fill and sublevel caving. Now the preferred stoping methodologyis long hole open stoping. Transverse or longitudinal methods are both used, dependent on the orebody characteristics. The change has been technically, socially, economically and politicallychallenging and at times has tested the abilities of those responsible for the operation of the mine. However, the benefits have been many. Safety has improved significantly, ounces from underground have doubled. Productivityhas doubled and underground unit costs have reduced bya third. These achievements have allowed the Obuasi mine to staycompetiti ve in this time of falling gold price. During 1999 and 2000 a full review of the mining and processing operations was undertaken, and as a result, the mine is now in a phase of restructure. Efforts are being made across the mine to improve efficiencies and to reduce costs. The future for the Obuasi Mine is an exciting one.

Jan 1, 2000

By Hohnen CA, Limerick JM, Hall DRT

An uniquely-designed flash furnace for smelting of nickel concentrate and for the recovering of metal values from the slag generated has been in successful use for nearly six years. Within the last eighteen months the ability of the furnace to treat slag arising from converting operations without significant reduction in capacity has also been successfully demonstrated. Previously, converter slag had been treated separately in an electric furnace. The salient features of smelter developments are outlined and slag chemistry is discussed. The low cost method for the introduction of coal to partially replace light fuel oil is reviewed and total energy requirements evaluated.

Jan 1, 1984

By J P. R de Villiers

The Vanderbijl Park sinter plant in South Africa was investigated to determine the reason for the production of very fine sinter not acceptable as feedstock for the blast furnace. A procedure was designed to generate representative samples and to prepare the samples for chemical and mineralogical analyses. Results from a mineral analyser showed that the samples are extremely heterogeneous and therefore the sampling and sample preparation methods had to be tested in order to produce representative samples. The high production capacity at the sinter plant could also give rise to sampling errors. The method designed involved sampling of the conveyor belt at the sinter plant every four hours for the duration of three days. The samples were then milled and split into smaller sections appropriate for analysis. X-Ray diffraction (XRD) and X-Ray fluorescence (XRF) analyses were conducted on the samples. The results showed a standard deviation of less then one per cent, which indicates that the samples were representative and that the method used was therefore adequate. Systematic differences in the phase proportions between normal and fine sinter samples were detected, with the fine sinter containing more haematite than the normal sinter. The sampling method employed gives added confidence that the differences are real.

Jan 1, 2008

By D M. Weedon

This paper introduces a novel roll crusher design, which incorporates non-cylindrical crushing rolls. The use of non-cylindrical rolls enables the crusher to achieve a greater reduction ratio than is possible with conventional roll crushers. Referred to as the NCRC (non-cylindrical roll crusher), the new crusher incorporates two rolls comprised of an alternating arrangement of plane and convex or concave surfaces. The two rolls are complementary and arranged so that when they rotate the convex and concave surfaces of each roll are substantially opposed. With the rolls rotating in opposite directions at the same speed, this arrangement produces a gap between the rolls that remains approximately constant. Discontinuities on the roll surfaces provide improved angles of nip, which increase the probability of larger particles being drawn into the crusher. Initial tests on a scale prototype of the NCRC have indicated that reduction ratios exceeding 10:1 are achievable.

Jan 1, 2000

The comparatively low winter rainfall, exposure to heavy salt laden coastal winds, and the consequent high evaporation rate, are important considerations in the rehabilitation of the Maslins Beach Sand Pit. The deficit of rainfall over evaporation is assessed at 1085 mm per annum. Such a coastal environment complicates the establishment of plants. The endemic flora found on the Sand Pit environs is mainly low wind-planed shrubs and mat plants. The dunes near the coast support an association dominated by Atriplex cinerea, Spinifex hirsutus, Scirpus nodosus, and Olearia axillaris. The coastal cliffs carry a more diverse vegetation dominated by Beyeria lechenaultii and Eutaxia microphylla. Overburden is used to develop a new landscape to screen operations, batter final faces, and cover rubbish at the nearby Council dump. The early overburden dumps were built with little regard for stability, but the more recent practice of using scrapers has resulted in more stable dumps. The erosion problems created by poor compaction have been controlled by contour banks, diversion drains, bitumen lined run-off drains, and hay mulching.

Jan 1, 1976

By K Uchino, M Inoue

Self-potential anomalies are generated by fluid pressure gradient, by temperature gradient or by chemical gradient. On the basis of this principle, a new technique is proposed to locate the fire source of spontaneous combustion of coal by the self-potential method. In order to investigate whether this method can be applied to locate the spontaneous combustion of coal in practice, surveys of self-potential distributions were undertaken in a coal waste pile undergoing spontaneous combustion. The results showed that there is a negative centre of the electrical potential distribution in the measurement area. The potential in this centre is about 140 mV lower than that in the surrounding area. Moreover, the negative centre of electrical potential distribution almost overlaps with the high temperature zone. Therefore, it is concluded that it is possible to locate the heat source by the measurement of self-potential distribution.

Jan 1, 2005

By McNicol J. H

Using a small scale laboratory pilot plant a series of tests have been conducted with the aim of investigating the influence of the zinc/acid ratio on the efficiency of zinc electrodeposition from an acidic sulphate solution. The results have shown that current efficiency is increased as the zinc/acid ratio is increased with no evidence of an optimum zinc/acid ratio. However the choice of a zinc/acid ratio for full scale operations must be a compromise between other parameters, spent electrolyte acidity and power efficiency, which also impact upon plant performance. The effect of various impurities has also been monitored and antimony, nickel and tin have been shown to be deliterious to current efficiency.

Jan 1, 1989

By Warren R

Croesus Shaft is one of two operating shafts on North Kalgurli Mines Limited's Fimiston lease.At the cessation of gold mining in 1974, the workings at Croesus were allowed to flood. Large quantities of deslimed mill tailings used in filled stopes were washed into the shaft and surrounding drives, making re-access very difficult. The shaft has been desludged from the 9 level to the 15 level, and a loading pocket installed below the 14 level. A vacuum lift unit was installed underground to facilitate the removal of the slime and spillage.Stoping at Croesus was hampered by poor drainage, pumping, and shaft availability. These difficulties have been overcome by utilising an open stoping system for the relatively steep, narrow, high grade stopes. Open stoping has proved to be effective and economic.

Jan 1, 1985

The ""multiple of exploration expenditure"" method of mineral valuation is applicable to exploration properties from the earliest stage of exploration to a moderately advanced stage but for which no resources have been delineated. While not recommended as a primary valuation method by some workers, others believe it to be the most satisfactory method of valuing exploration properties until it is possible to employ a DCF technique. In many situations facing the professional valuer, the method may represent the only semi-quantitative option available and is frequently used. Significantly it often forms the starting point in discussions to farm-in on an exploration tenement. The paper briefly reviews the definition of value as applied to mineral valuation and in particular examines the relationship between fair value and market clearing price in ""fair"", bull and bear markets. The multiple of exploration expenditure method uses previous exploration expenditure and/or future committed exploration expenditure to derive a base value for the tenements. This base value is multiplied by a prospectivity enhancement multiplier (PEM) with adjustments for market premium or discount and consideration of the quality of the exploration team to derive a fair value for the tenements. The paper will demonstrate that there is no necessary nexus between fair value derived from the method and present book Values.

Jan 1, 1994

Subsidence prediction methods can be divided into two basic types: empirical and analytical. Empirical methods are based largely on a combination of experience, intuition and observations from a large number of observed subsidence data. They are simple in their application, but they are not based on any principle of mechanics. Analytical methods are based on equivalent material modelling principles, where the ground surrounding the extraction is mathematically represented by idealised materials that deform according to the principles of continuum mechanics. Wide applicability and improved understanding are the principal advantages claimed for this approach. In NSW, significant progress has been achieved in the area of subsidence prediction during the last ten years. Empirical prediction curves are available in NSW for predicting the ground movement in the Southern and Newcastle Coalfields. A' comparison of subsidence values predicted from these curves with the actual monitored values indicates that the curves are adequate for use in conjunction with the existing damage assessment methods. Future research for improving the existing empirical prediction curves can only be justified if it is cost effective. There are several numerical models currently in use in NSW for predicting subsidence. The models do not appear to be superior in their ability to predict subsidence when compared with the empirical curves. the performance of these models will no doubt improve along with advances in defining strata properties and failure mechanisms.

Jan 1, 1991

By Smith P

The past 20 years have seen the replacement of hydraulic control of longwall mining systems by the neater. smaller and better controlled electronic units.Early problems of moisture and other effects on reliability were overcome to see electronically controlled supports chosen for Corrimal Colliery ten years ago. Lessons from Corrimal and elsewhere, with following improvements and sophistication led to wider use as exemplified by Meco and other electronically controlled supports used in more recent installations in New South Wales, Queensland, USA and Czechoslovakia of the total of over 80 electronically controlled support installations worldwide in the past decade. Present work is toward a fully "integrated face" of British Coal by 1993, incorporating the Meco automatic face straightening system already due for practical use in the UK later this year. However the manless face still appears to be some way off although the present minimum crews and close monitoring, including early warning, are promising stages.

Jan 1, 1991

By Mishra BK, Agrawala S

The traditional method of scale-up uses the population-balance model. In particular, the selection function values for a material are determined in a laboratory mill and a variety of correlations are used to scale these values to plant scale mills. For example, the factor D2-5L (D-mill diameter, L-mill length) appears in many power correlations. The number of collisions is proportional to the number of balls (aD2L), the frequency of mill rotation ((x 1/4D-) and effectiveness of impact ((XD), which gives rise to the 'D2.5L' expression. However, what is lacking in this expression is that it does not throw light on the intensities of collisions. In other words, the collision intensities in both laboratory and plant scale mills are implied to be identical. This fact has been very limiting. Alternatively, the collision frequencies and intensity of impacts can be computed with the discrete element code. This code computes the motion and collision of each individual ball in the ball charge. Therefore the number of collisions and the fraction of collisions in the energy range Et, E2.òòE. (collision energy density) are calculated for a given mill size and operating conditions. Then, using the breakage function determined in drop-weight experiments, the evolution of size distribution is computed for a lab mill. The collision frequency and energy density for larger mill sizes are shown. The fundamental theory outlined for the calculation of size distribution is equally applicable for the large mill, which is the basis for scale-up.

Jan 1, 1993

The Coke Ovens Laboratory at Australian Iron & Steel, Port Kembla has been involved in the analysis of seam gases and mine airs for approximately twenty (20) years. This period has seen many developments and changes in the techniques used to the point when the current techniques are equal to other labora- tories involved in similar analyses. The laboratory has NATA registration for the analysis of mine airs and gases. Apart from routine testing of seam gases, ventilation airs and gases emmitted from coal bore cores a number of projects have been undertaken. These have served a twofold purpose, one to provide information to the customer, generally Collieries Research and Technology and secondly in developing the skills and capabilities of the Coke Ovens Laboratory. This paper discusses the development and services available at the Coke Ovens Laboratory for the analysis of gases and airs from collieries.

Jan 1, 1983

By J C. Macintosh

Capcoal Mine has modified its water use practices over the past 15 years. Two issues have changed the way water was managed:an economic review of water supply options for a planned expansion of the coal handling and preparation plant (CHPP) in the early 1990s, and increasing neighbour concerns about discharge of worked water from the mine into the local streams. These issues resulted in commitment by the site General Manager to cease discharge of worked water from site and to convert from using raw water to worked water in the CHPP. Operational needs, societal demands and continuing dry weather are again demanding change to the siteÆs water management strategy. This paper outlines the drivers for past and future operational change.

Jan 1, 2006

The use of operational research in mining is illustrated by simple examples of the techniques of simulation, linear programming, theory of sampling, and experimental design.Statistical simulation of the delays in answering telephones was used to compare the efficiency of alarm systems in collieries, and to determine stock control policy for a bin in mucking, filling, and tramming operations. Linear programming was used to help minimize transportation costs between collieries and washeries. The theory of sampling was applied to separate and balance the components of error introduced at the' various stages in the collection and reduction of routine samples of coal, and to the assessment of errors of estimates of grade in orebodies from drill samples. 'l'he principles of experimentaldesign were used to compare wear of different conveyor beltings and costs of battery and diesel locomotives in underground transport.INTRODUCTIONIn operational research some of the procedural techniques and professional attitudes of mind found among scientists and, in particular, mathematicians and statisticians, are applied to operational problems in industry ranging from policy making in the broadest sense to the humblest sampling procedures. These apply in mining equally with other industries.Anyone who reviews a procedure critically and in a systematic way may legitimately claim to be doing operational research. On the other hand, what is found in books on operational research is usually a collection of mathematical and statistical techniques which, though forming only a corner of operational research activity, illustrate the novel approaches to problems which characterize the discipline and which would probably not occur to the un...

Jan 1, 1962