Search Documents

With some notable exceptions, marine placers located just below, or just above, present sea level, are responsible for much of today's production of detrital ilmenite, rutile, zircon, and other minerals of value. The purpose of this paper is to discuss the paleogeographic and paleo-oceanographic factors which may have determined the location of presently submerged marine placers. These factors-include changes in sea level, burial by recent marine sediments, stream capture and other i changes in drainage patterns, and recent changes in climate. Selected geologic situations in the Yellow Sea off the coast of Korea, in the Atlantic Ocean off the coast of Portugal, in the Bering Sea off the coast of Alaska, and in the Arabian Sea off the coast of India, will be used to illustrate the author's point of view.

Jan 1, 1980

By G Senanayake, J Andreazza

The general experience in gold cyanidation research activities and plant practice is that high oxygen and cyanide concentrations improve gold leaching kinetics which in turn reduce residence time and increase throughput. This paper shows how the improved pre-oxidation method for the pyrrhotite rich gold ore of Bounty Gold Mine has increased gold recoveries at lower reagent consumption rates. The installation of a pipe reactor, in conjunction with a Multi Mix Systems oxygen injector, has lowered the amount of oxygen required to achieve a dissolved oxygen level target of 20 mg/L. The improvement of the pre-oxidation stage and lead nitrate solution addition has led to a reduction in the free cyanide concentration required for leaching, resulting in a decrease in cyanide consumption rate by 36 per cent to achieve a one to two per cent improvement in the gold recovery.

Jan 1, 2002

This paper gives a first-hand account of what a graduate mining engineer can learn by visiting Atlas Copco in Sweden and gives reasons why all mining engineering students should apply for this excellent scholarship. It will also (attempt to) refute the authorÆs mine managerÆs claim that the trip was a huge junket.

Jan 1, 2006

A simple method of designing effective fill drainage systems for slurry backfill is presented. By using the proposed method, it is easy to calculate and predict the expected fill drainage rates or to provide additional drainage systems to accelerate the fill drainage. The fundamentals of hydraulic fill and an efficient method to determine its permeability is also explained. The safety in hydraulic filling and bulkhead stability depends totally on achieving effective drainage regime for the fill. This paper provides the basis for creating such efficient drainage regimes. The recent fatal fill bulkhead failures in Australia were the result of poor drainage from the respective fill masses, and therefore it is more important to provide suitable drainage arrangements to continue using hydraulic fill to the benefit of the mining industry. At present there is no procedure available to mine operators to estimate the expected bulkhead pressures to design a satisfactory bulkhead. Some mines are constructing bulkheads after their initial investigations carried out years ago. Other mines have simply borrowed the ideas from the pioneer mines and using in their areas. It is high time that we develop a rational approach to estimate the expected bulkhead pressures for the design of bulkheads. We need a simple model that could be understood and used by the mine operators on a day-to-day basis. This paper also presents a model to predict the bulkhead pressures for designing safe bulkheads.

Jan 1, 2002

The process of refurbishment is not a precisely defined one. It is under- stood to mean an upgrading of a plant which is normally performed only once. The application of refurbishment in the field of materials hand- ling equipment poses particular problems because complex plants con- sist of individual components having quite different remaining service lives. For this reason, a systematic, proven procedure is proposed for the refurbishment of large materials handling equipment, designed to ensure economic implementation in accordance with the company goals. Rheinbraun2 has been using materials handling equipment since 1900, the largest units today being bucket-wheel excavators with a daily capacity of 240,000 bank cubic metres of overburden and a service weight of up to 13,500 t (metric tons). Since 1975, more than 50 large-scale refurbish- ment projects have been carried out in the company. In the process, refur- bishment has turned out to be the proven alternative to replacement of large materials handling equipment. Rheinbraun Engineering,3 a Rhein- braun subsidiary, carries out planning, consulting, and supervising work in the implementation of refurbishment projects in Germany and abroad. The most recent example is the refurbishment of Dredger 11 of the State Electricity Commission of Victoria in cooperation with Krupp-Australia, Melbourne.

Jan 1, 1989

A method is presented for calculating the number of cycles of stress to failure of a drill rod from operating variables; a mathematical analysis by Cooper of the stresses present in drill steels is applied to the forged collar, i1i-in. hexagonal hollow drill steel in common use in Australia; and an estimation is made of the dry fatigue limits at various points along a drill rod.It is shown that these calculations predict failure at a 'point where failure rarely occurs, and do not predict that failure should occur where it does in practice. The reasons for this anomaly lie in the neglect of bending stresses in the stress calculations, and in failuredue to corrosion fatigue at a preferred section rather than to simpler fatigue under non-corrosive conditions.INTRODUCTIONIt has long been recognized that failure of metal sections by fatigue is influenced both by the number of cycles of stress imparted to the section (N) and by the magnitude of this cyclic stress (8). In this paper, both Nand Shave been calculated for rods which have failed in service, and whose operating history is known. While the calculation of the number of cycles to failure is·simple, the calculation of stress is more complex. The results of stress caIculations predict that failure should occur only hi short rods, and then preferentially at the tip end rather than the shank end.However, in actual fatigue failures of steel rock drill rods, approximately 75 per cent. of such failures are close to the shank end, and failures near the tip end are rare.The usual explanation given for this high incidence of shank-end failures is that at the point of failure there exists, in forged collar steels of the type common in Australia "hardness valley" or. "m'etallurgical notch". This narrow valley in hardness is a weakness, and failure is expected to occur at the weakest point at the bottom of...

Jan 1, 1955

This paper comprises a discussion of standards for comparing conditions in mines, of methods for measuring the flow of air, of a comparison of fan performances, and the application of these matters to mines in Western Australia.UNDERGROUND CONDITIONSIn approaching the question of mine ventilation one naturally searches for some standard by which to measure the conditions in a mine.There are several clauses in the Mines Regulation Act defining the conditions which are permitted. The quantity of CO2 is limited to 0·25 by volume, but the estimation of CO2 involves a chemical determination and is not suited for general use in a mine.The maximum temperature is fixed at 87 0 F. (dry bulb), and at 80° (wet bulb). The reading of temperature is easily done in the working places, and this is a very valuable and practical test of the conditions in a mine.The wet bulb temperature is probably the most important factor in determining working conditions. It is obvious that human life cannot be sustained for any appreciable period if the wet bulb temperature is above blood heat (about 97°F.). In places where the wet bulb temperature is 90°F. there is danger of heat stroke.In places where the air in a mine is still, the wet bulb temperature rises to a value close to the rock temperature.Adequate ventilation cools the workings by transference of heat from the rock to the air stream, and the temperature...

Jan 1, 1939

By H Kundapen, B Bolton, S Miller

The Ok Tedi porphyry copper and gold mine is an open-pit operation located within the Star Mountains in the Western Province of Papua New Guinea and is situated near the headwaters of the Ok Tedi-Fly River system. The climate is equatorial sub-alpine with rainfall ranging from five to ten metres per year. Mining commenced in 1984 and to-date approximately 500 Mt of waste rock has been produced. A failing waste rock dump system operates whereby the dumps are eroded by tributary creeks of the Ok Tedi. It is estimated that approximately 250 Mt of waste is retained within the upper reaches of the river system. The waste rock comprises both potentially acid forming rock and limestone and to-date the overall waste has been acid consuming. However, the long-term mine plan identifies declining limestone production and hence an increasing risk of acid generation over the remaining years of the operation. A program was initiated to determine the net acid producing potential (NAPP) required (ie target NAPP) to minimise the risk of acid generation within the waste rock dumps. The results from this program provide guidelines for an operational target NAPP strategy to provide sufficient acid buffering across all size fractions in the waste rock dump for long-term ARD control. Implementation of this plan requires additional limestone to be mined and co-disposed with ROM waste rock.

Jan 1, 2003

Microorganisms have been used throughout history for the benefit of mankind with some of the earliest applications being in the production of fermented foods and beverages. Reactions involving inorganic substances such as metals, sulphur and sulphide compounds were hardly ever used until the early 1900s when it was discovered that Thiobacillus ferrooxidans was capable of promoting the oxidation of metal sulphides in ores. Today, it is widely recognised that biotechnology has great potential in the minerals industries, particularly in such areas as the leaching of low-grade ores of metals such as copper, gold and uranium; removal of heavy metal ions from process streams and from liquid process wastes; and in the desulphurisation of high-sulphur fuels. Although widespread commercialisation of mineral biotechnology has not yet been achieved, it is estimated that by the Year 2000 mineral biotechnology will have a significant impact on the minerals and metal industry and will probably account for tens of billions of dollars worth of annual production world-wide. This paper examines the actual and possible future applications of biotechnology in the minerals, metal refining and fossil-fuel processing industries. Firstly, the important chemical (and biochemical) principles involved in bio-dissolution of metals from ores and solid wastes, and in bio-accumulation of metals from process and waste solutions are reviewed, including leaching practices - past, present and future. Microbial desulphurisation of coal, and microbially-enhanced oil recovery are also discussed. The practical aspects of genetics and genetic engineering, the types and characteristics of those microorganisms important to mineral biotechnology, and the current research trends are reviewed as well. KEYWORDS: Biotechnology, microbial leaching, bioaccumulation, biosorption, bioleaching, biohydrometallurgy.

Jan 1, 1993

By C J. Corbett

Many underground mining methods rely on blasted rock moving under gravity to report to extraction points. Mining of orebodies dipping between 20 - 45 degrees poses a unique challenge for mining engineers in that a dip angle in this range will not allow the movement of broken ore down the footwall to the mucking horizon utilising gravity. This is more so in cases where the natural angle of repose of the rock is less than the dip of the orebody. Hence, innovative mining systems are necessary to mine this type of orebodies. In Australia, the method of uphole retreat panel stoping is commonly used to extract orebodies in the dip range of 20 - 45 degrees and thickness range of 5 - 15 m. In the Zambian Copperbelt a method called continuous retreat updip stoping is used for orebodies with similar dips and thicknesses. The mechanised form of this mining method has potential for application in the metalliferous mining industry in Australia. In this study a comparison is made between mechanised updip (MUDS) and transverse retreat stoping (TRS) methods. A hypothetical nickel sulphide orebody located in Western Australia is used as case study. The net present value for mechanised updip stoping is seven per cent higher than that of transverse retreat stoping based on the assumptions applied. Initial results of this study indicate that mechanised updip stoping can be adopted for Australian mining conditions. However, lack of significant local experience with the method is often cited as a reason for not adopting it even in situations where it is clearly the best option.

Jan 1, 2003

A blast is designed to completely break competent rock such that it can be economically extracted, and efficiently handled or processed. Efficient breakage of the rock is critical to the success of an operation, and in many operations blast design is optimised to achieve fragmentation, muckpile profiles, and material that is easily excavated. There are inevitably other issues, such as damage to adjacent rock, that should be taken into account when designing a blast to achieve overall optimisation. Some of the key issues with respect to the integrity of the in situ materials adjacent to a blast are identified and briefly discussed in this paper. The potential for damage and the effects of a blast will be strongly influenced by the rock mass properties. This makes it important that site specific conditions and their response to blasting are known. Practical techniques that allow the disturbance adjacent to a blast to be measured with minimum disturbance to operations are described in the paper. Experience shows that, during the blasting process, there is considerable potential to disturb the in situ rock mass adjacent to the blast. In some circumstances a very important objective must be to minimise disturbance outside of the immediate blast area. Measured and observed disturbances caused by blasting to adjacent rock, for various common types of blasting, are discussed in this paper. Blast induced disturbances to the rock mass have been observed in both the near and far fields. These disturbances have the potential to impact on geotechnical design. The geotechnical significance of blast disturbance on a rock mass that is to remain in situ is explored and suggestions with respect to design are given.

Jan 1, 2004

By Kershaw M. G

At the Risdon plant of the Electrolytic Zinc Company of Australasia Limited, impurities toxic to the electrolytic production of zinc metal, notably arsenic and antimony, have traditionally been coprecipitated when precipitating iron as ferric hydroxide. With the development of a new lead/zinc mine at Elura, New South Wales, it was anticipated that the concentration of impurities, particularly arsenic, in the zinc sulphide concentrates treated at Risdon would increase. This suggested that an increase in the capacity of the iron purification step in the Risdon plant would be required to cope with the higher input of these impurities.Laboratory investigations showed that the additional capacity would be achieved, either by a large increase in the amount of iron used as the "collector" in the process, or by a two-stage process. The latter approach was preferred as a increase in the amount of iron precipitated would lead to much higher operating costs and overloading of the existing equipment.In the two stage procedure, acidic iron bearing solution is added to solution feeding the first stage and most of the arsenic removed from solution when iron is precipitated from solution by neutralisation with limestone. Mter separation of the precipitated solids, acidic iron bearing solution is added to the solution, and remaining arsenic removed almost completely following neutralisation by limestone.This paper describes the laboratory and pilot plant results and the plant modifications required. Abrief account is also given of the operator training and acceptance in the use of the digital control facilities installed in the new plant.The new plant is working well and good solution purity is being maintained despite a substantial increase in the concentration of impurities in the raw materials.

Jan 1, 1990

By Davison GR

The cost of drilling consumables is always a large component of any mine budget. It is important that this cost be carefully examined with a view to reducing the overall cost per inetre or at least minimising its escalation.At Renison it is considered that the only way to ensure drilling costs do not rise unduly is through a total system of control from purchase to disposal.In 1979 extension of an existing drill supply service contract was carefully examined and abandoned in favour of a hybrid system. This system is providing a great deal of control over the use of drilling consumables and has maintained a relatively constant cost per drilled metre over the last five years.Current consignment stock contracts for drilling consumables are strictly specified by the Technical Services section of the Mine Department and consumables purchased under these contracts are distributed and refurbished/sharpened by a contractor.The total result of this package is individual drilling items that achieve the best cost per metre and careful distribution and maintenance to ensure maximum life.

Jan 1, 1985

By M E. Trim, J J. Johnson, W Cranston

The Brightwater conveyance system is located near Seattle, Washington in the north-western United States. The East Contract portion of the system consists of a 4.3 km long, 5.9 m diameter tunnel in soft ground and two large shafts constructed in challenging soil conditions. The two shafts are situated side-by-side in an urban valley. One will house an influent structure to direct incoming sewage and outgoing treated effluent, while the other will house a 645 megalitre per day (ML/d) influent pump station. The tunnel contains four pipelines: two force mains to convey untreated wastewater eastward from the new pump station to a new treatment plant, one gravity-pressure pipeline to convey treated effluent westward to a new outfall in Puget Sound, and one high-pressure pipeline to convey reclaimed water from the treatment plant to downstream distribution points. The shafts and the tunnel presented many design challenges. Groundwater is near the surface in the area surrounding the shafts, and compressible peat and clay soils preclude dewatering during construction. These and other challenges were encountered during design of the pump station shaft and multiple-pipe tunnel. The challenges were addressed by a design that includes a dual intersecting circular cell shaft (referred to as æthe peanutÆ) and a single tunnel into which stacked pipes will be æstuffedÆ. This paper discusses the design approach and design details for both elements.

Jan 1, 2008

In general, modern mining companies all over the world have to face the same economic circumstances as any other part of the industry: considering the tough competition, production and haulage costs must be reduced permanently whereas productivity has to increase substantially in order to remain price-competitive. However, the imposed pressure also offers the chance for consideration of alternative mining concepts, the application of which can result in substantial cost savings and improvements in the quality of the mined material. As one of these alternative mining concepts, surface mining technology offers substantial improvements in productivity. It also influences aspects of haulage, such as safety and speed, in a positive way. The capability of selective mining ties in nicely with the production of small-sized crushed material, the granulometry of which allows the elimination of the primary crusher. Mine operators profit from reduced costs for the maintenance of their haulage vehicles due to reduced wear, a decreased likelihood of accidents and higher average transport speeds. Surface Miners can also be used to cut haul roads into virgin rocks and leave a clean and level surface behind, improving the quality of these created roads. Thus, it is even possible to use ordinary road trucks for transport in mines. The current paper outlines in detail the effects of the surface mining technology on mining and haulage aspects and reports on applications where substantial cost savings could be achieved due to the application of what is also referred to as æsimple mining processÆ.

Jan 1, 2003

Major exploration companies can have a problem with what to do with small precious metal ore bodies located through exploration programmes. Low tonnage, but high grade, ore bodies too small to justify in-house development.1.2 Ban Ban Mining is a Sunshine Coast based partnership with considerable expertise in mining and earthmoving which specializes in the mining of small/medium size ore bodies on behalf of the tenement holder on a profit sharing or royalty basis.1.3 The partnership's first successful venture has been the mining and vat leaching of a small 40,000 tonne ore body with a head grade of 5 gm/tonne gold and 32 gms/tonne silver, situated near Ban Ban Springs in southeast Queensland.1.4 This paper looks at the low cost vat leaching method of treatment, as an alternative to CIP and CIL in the processing of low tonnage/high grade precious metal ore bodies.

Jan 1, 1990

Tin mining has taken place in the New England region of New South Wales since 1872. Until fairly recent times there was little pro- vision made for environmental protection. Mining methods,which included ground sluicing and open cutting,had considerable environmental impact. Much of the topsoil was lost and there is little vegetation on the infertile and at times toxic, subsoil. Thus much of the lands disturbed by mining have not been stabilised and are eroding, causing extensive pollution of adjacent watercourses. There are more than 1500ha of abandoned tin mine sites in the New England, representing one of the worst rehabilitation problems in New South Wales and reflecting poorly on the mining industry as a whole. Recent tin mining operations incorporate progressive rehabilitation in their mining cycle. Topsoil is stockpiled and later respread. This topsoil contains a seed source, facilitating revegetation and thus stabilisation. The tin mining industry, under considerable cost pressures at present, is seeking a cost- effective revegetation technique. Most of the mines in the New England are situated in a forest environment. Trials have been conducted in the past using exotic pasture species with limited success due to the characteristics of the subsoil. Other revege- tation trials have used pine or eucalypt tree species. The cost of these techniques is a major disadvantage. Certain acacias species were observed colonising disturbed tin mining areas on very infertile subsoils. Acacias have a number of characteristics indicating a possible applic- ations in mine rehabilitation programmes.

Jan 1, 1987

By T J. Sheer

Water vapour refrigeration (systems using water as the refrigerant) could potentially be used to provide chilled water at underground locations in mines, as an alternative to conventional refrigerators using refrigerants such as R-134a. The use of water as both the primary and secondary refrigerants is attractive in concept since direct-contact heat exchangers could be used, yielding higher coefficients of performance. The disadvantage of water is the very high specific volume of the vapour at low pressures, which leads to great challenges in compressor design, as has been reported previously in the context of slurry-ice plants for mine applications (Ophir and Koren, 1999). Steam ejectors have long been known as alternative compression devices for refrigerators, but no work has been done previously on the possibility of using ejectors powered by high-pressure water, which is readily available in mines from long pipe columns in vertical shafts. This paper presents the results of a laboratory investigation into the use of high-pressure water as the motive fluid in an ejector refrigerator. No previously reported liquid ejector system has achieved subcooling of the process fluid, ie a reduction in fluid temperature within the evaporator to a level below that of the motive fluid. In contrast, the present work demonstrated that subcooling could occur at motive water pressures above 5 MPa. Mine cooling applications were considered and it was concluded that while this concept would not be feasible as a mine-wide cooling source, there could be specialised applications where it would be beneficial. One application would be to cool backfill and thereby reduce the heat load at the working face. In this case the best performance would be achieved by using the ejector in combination with an energy recovery system such as a Pelton turbine or a three-chamber pipe feeder.

Jan 1, 2005

By C O. Gomez

The bubble size, together with the gas rate, determines the bubble surface area flux in flotation machines and, therefore, impacts directly on the kinetics of flotation. Understanding the variables that influence bubble size is one of the keys to understanding flotation recovery. Surprisingly, these relationships are poorly understood, largely due to the difficulties associated with gas dispersion measurements in industrial environments. The McGill gas dispersion sensors (bubble size, gas rate, gas holdup) are capable of reliably making such measurements. This paper reports on a study, using the McGill sensors in a 0.8 m3 Metso RCSTM pilot cell, which investigated the effect on bubble size of frother type and concentration, gas rate, temperature and rotor speed. A Denver laboratory cell was used to investigate the effect of elevation above sea level. Frother concentration proved to have the predominant influence on bubble size, and the effect of frother type can be normalised as a function of the critical coalescence concentration (CCC). Measurements made at many plant sites worldwide are compared to the model developed using the Metso RCSTM unit.

Jan 1, 2007

In preparation of this Paper, the emphasis has been laid on the commercial rather than on the technical and scientific aspects of coal evaluation. It is intended to describe and comment on the principal factors which currently determine the selection and procurement of coking coal for the steel industry, and is not based on the results of any original research by the author. Evaluation of different coals for strictly thermal uses, for gas production or other chemical applications has not been attempted, and comparisons of coal with other fuels have been excluded: the paper is concerned only with coals for the production of blast furnace coke. The discussion is strongly related to, and illustrated by, British, and to some extent, other Western European practice, but it is hoped that the general conclusions may have a wider application.

Jan 1, 1975