Search Documents

By W. P. Campbell

Introduction OWING to the necessity of curtailing the length of this paper, nothing like an exhaustive treatment of the subject will be attempted. Instead, merely a few aspects will be considered, viz., water trouble in wells, sampling of waters, analysis, methods of reporting analysis, and the comparison of a few typical waters. The waters discussed will not be confined to those occurring in areas where oil or gas has already been found, but will include samples from areas in which drilling is being carried on in the hope that oil or gas may be found, i.e., from unproved fields. The Water Problem The problem of dealing with water encountered in oil and gas producing areas has engaged the attention of petroleum engineers from the early days of the industry. Water was not always considered a menace to oil sands; indeed, a certain amount of it was considered beneficial in some areas, but if such exist today they are very exceptional. In some fields, the problem is more acute than in others, and at times has baffled all attempts to solve it satisfactorily. Wells have been brought-in with promise of good production, but after a brief period have 'gone to water'. Whether ?it has always been a case of poor engineering in the form of unsuccessful water shut-off of 'top' or 'bottom' water, or because 'edge' water was present and water and oil were in such close contact it was impossible to remove the one without the other, is hard to say.

Jan 1, 1929

By G. Tairova, M. Murchie, B. Esford, E. Lam

"The objective of this project is to investigate methods to lower the sulphate concentrations in the mill effluent. Currently, the concentration of sulphate in mill effluent is approximately 2 g/L. The high concentration of sulphate ion in the effluent has the potential to become a regulatory issue. The target sulphate concentration in mill effluent for this work was less than 500 mg/L. The pilot studies, using sulphate precipitation, were carried out at the mill. The results of the sulphate precipitation pilot study, using calcium hydroxide and sodium aluminate, indicated that:• The sulphate concentrations in effluent could be reduced to less than 500 mg/L.• The concentrations of most other elements of concern, such as selenium, arsenic, cobalt, nickel and vanadium, were also reduced.INTRODUCTIONHistorically, the concentration of sulphate, SO4 2-, in water has not generally been subject to regulation. However, with the increasing global consumption of water, stricter regulations on sulphate quantity may be imposed. Sulphate is a concern in process waters as it forms scale on process equipment and leads to operational problems. High sulphate concentrations may result in adverse health effects. The taste theshhold for the most sulphate salts in drinking water ranges from 250 to 500 mg/L.A literature search and review to identify methods to reduce sulphate concentration in the mill effluent was carried out. A number of methods were selected and tested in the lab. The experimental results indicated that the precipitation methods, using calcium hydroxide and aluminum compounds, barium compounds, as well as the ion exchange and the membrane methods, were effective for the removal of sulphate to below the required limits. Some other elements, such as vanadium, nickel, cobalt, selenium and molybdenum, were also removed.The process, using calcium hydroxide and aluminum compound for sulphate precipitation, similar to the Cost Effective Sulphate Removal (CESR), also known as “Walhalla” process, described in the Montana Tech report (“Demonstration Of Sulfate Removal” 1999), was selected for further consideration [1]. In the CESR process, the water is treated with lime for precipitation of gypsum, followed by the reaction with a proprietary aluminum compound for removal of a residual sulphate. The final pH adjustment is carried out using carbon dioxide. Results of a preliminary cost estimate indicated that the removal of sulphate using calcium hydroxide and aluminum compound was the preferred method of treatment, considering its low cost, availability of chemicals and minimal changes to the existing plant circuit."

Jan 1, 2012

By H. Marquis

The present paper consists of a survey of the literature on the problems of abrasion and wear of metals and materials by suspended matter. This problem is a very general one in industry, and is especially notice-able in the operation of cyclones and other types of dust collectors. The problem of abrasive dust in corrosive gas environments, such as commonly encountered in metallurgical industries, is particularly severe. Very little work has been done in the study of this type of abrasive wear, especially at high temperatures. However, a general review is presented here of all the work published on related subjects, such as that involving sand erosion in turbines and water wheels and the effect of temperature on friction wear. Topics in this paper include: blasting wear by sand, quartz, limestone, silicon carbide and other refractory particles; methods of investigation; effects of velocity, temperature and *Canadian Armament Research and Development Establishment, Valcarter, P.Q. angle of attack; correlation between indentation hardness, scratch hard-ness and resistance to abrasion; the effect of protective coatings; resistance of various metals; etc.

Jan 1, 1962

"2.1. General Considerations and Properties2.1.1. IntroductionOur present knowledge of the platinum-group elements (POE) is extensive, the reason being two-fold. The elements have many uses and, moreover, they exhibit extremely varied chemical behaviour, depending on their state of oxidation and chemical environment. The present chapter reviews a selected body of material which is of particular relevance to mineralogy and geochemistry.Comprehensive treatises on the POE include those by Mellor (1956-1957), Gmelin (1938-1957) and Pascal (1958). The inorganic chemistry, particularly coordination chemistry, has been dealt with in works by Griffith (1967), Hartley (1973) and Livingstone (1975), and the analytical chemistry by Walsh and Hausman (1963), Beamish (1966) and Beamish and Van Loon (1972, 1977). Darling (1973) and Savitsky (1978) have reviewed the metallurgical properties and applications of the metals. Goldberg and Helper (1968) have reviewed the thermochemistry and oxidation potentials of POE systems, and Wagman et at. (1969) have also provided selected values of their thermodynamic properties. The geochemistry of the POE has been reviewed by Yushko-Zakharova et at. (1967), Cousins (1973), Cabri (1974), and Naldrett and Duke (1980).Platinum was used briefly as a coinage metal in ImperialRussia. Otherwise, the principal early use for platinum and its alloys was in the fabrication of chemically resistant apparatus. Subsequently, a large part of platinum production was utilized for catalysts in the sulphuric acid and ammonia industries. Platinum has been replaced by vanadium pentoxide in the manufacture of sulphuric acid, but, in recent times, catalytic upgrading of petroleum and emission control systems for automobiles have opened further huge markets for the metal. All of the POE find uses either as reagents or catalysts in the synthesis of organic compounds, e.g., in the Wacker process, which uses palladium chloride to catalyze the production of acetaldehyde from ethylene. There are, of course, a large number of specialized uses for the elements, particularly in alloys, temperature measurement devices, cancer therapy and so on."

Jan 1, 1979

By V. S. Papezik

Pyrophyllite, an AI silicate used in the production of ceramic materials, is formed mainly by alteration of felsic to intermediate volcanic rocks, either directly (at temperatures of 250-300°C and pressures of 1-2 kbar) or by subsequent low-grade metamorphism of aluminous protoliths produced by thermal fluids or even by prolonged weathering. Most pyrophyllite deposits in North America are concentrated in a belt of Late Precambrian volcanic and sedimentary rocks, the "Avalon Zone ", which extends along the eastern flank of the Appalachian mountain system from Newfoundland to the southeastern U.S.A. The only producing pyrophyllite mine in Canada is an open pit located near the settlement of Foxtrap on the Avalon Peninsula of Newfoundland. It lies in a belt of rhyolitic flows and pyroclastics intruded by a granitoid pluton. The rocks have been leached along a shear- or fracture zone, depleted in silica, alkalies, Ca, Mg and Fe by the action of hydrothermal fluids, and recrystallized to a very fine-grained massive assemblage of pyrophyllite, muscovite ("sericite") and quartz. High-grade pyrophyllite lenses contain small nodules of diaspore with minor barite; rutile is present in trace amounts. The close proximity of all pyrophyllitized zones on the peninsula to the granite contact suggests that the alteration was produced by thermal fluids genetically connected with the granitoid pluton. The fine-grained pyrophyllite-bearing rocks, with their simple mineralogy, are suitable for quantitative modal analysis by X-ray diffraction. Chemically analyzed samples from the alteration zone were used for the construction of working curves by plotting calculated mineral content against the intensity of selected diffraction peaks. The accuracy of the resulting curves is ±4.5% for quartz, ±3.6% for pyrophyllite and ±2.7% for muscovite. Pelletized samples give best results. The XRD method is suitable for a rapid analysis of a large number of grab or core samples to outline higher-grade areas for more detailed sampling.

Jan 1, 1978

By Claude Hubert, Alex C. Brown, Pascal Marquis, D. M. Rigg

"Numerous studies of the Bousquet mining district, Abitibi, Quebec, mainly following the successive discoveries of new gold deposits over the past two decades, have led to a broad range of genetic hypotheses for their gold deposition. A compilation of petrographic, structural, and geochemical data indicates that the gold deposits are composed chiefly of pyritic schists derived from felsic and mafic volcanic and volcaniclastic protoliths, and of auriferous massive pyrite hosted by pyritic schists of felsic affinity. The deposits are typically located within zones of local pyrite enrichment and advanced-argillic alteration which are in turn enclosed within much larger zones of disseminated pyrite included in regional-scale, commonly anastomosing, zones of sericitic alteration.Overprinting relationships between three sets of folds and foliations indicate that the host-rocks of the gold deposits have retained the imprint of three successive generations of ductile deformation resulting from regional dynamothermal metamorphism. Sericitic and advanced-argillic alteration, together with massive sulphide deposition, are interpreted to have taken place prior to the onset of the ductile deformation, based on observations 1) of altered fragments of wallrocks which are enclosed within massive sulphide bodies and were thus preserved through regional metamorphism, 2) of the syntectonic deformed pyrite, and3) of the syn-tectonic porphyroblasts of andalusite, garnet and plagioclase. The orebodies are oblate to prolate, and the pyrite-gold mineralization is typically vein-type, distributed in foliation-oblique and foliation-parallel veins. The gold-bearing structures postdate all foliations, and are associated with retrograde alteration assemblages that are pseudomorphic after pea~-metamorphic porphyroblasts in host-rocks, and with cataclasticfabrics that overprint syn-metamorphic pressure-solution features and annealing fabrics in pyrite.Retrograde gold-bearing assemblages indicate a chemical disequilibrium between the ore-forming fluids and their host rocks. This disequilibrium rules out the possibility that gold was remobilized from its own host, and suggests, instead, that the ore-forming fluids and their metal contents had an allochtonous source. Stable and radiogenic isotope analyses indicate that the fluids had a metamorphic origin, and that the associated alteration took place after the culmination of the Kenoran orogeny."

Jan 1, 1990

By F. Siciliano, D. Bai, S. Yue, A. M. Elwazri

The influence of niobium addition and very low temperature (`cool') deformation on the microstructure and properties of low carbon microalloyed steels was investigated. In this work, the specimens were heated at 1200°C and held at this temperature for 20 minutes. Some specimens were aged at 400°C for times ranging from 10 minutes to 10 hours followed by air-cooling. Others were subjected to deformation at 400°C (`cool deformation') prior to aging. It was observed that the proportion of acicular ferrite was increased as the amount of Nb was increased. It was found that cool deformation increased both yield and tensile strengths significantly compared to that of the aged only specimens.

Jan 1, 2005

By D. Emadi

The ASTM B108 Mould and a Modified Mould were used to cast test bars under a variety of conditions: mould and pouring temperatures, mould coating and tilt. Mechanical properties were determined in the as-cast and heat-treated conditions. The ASTM Mould is less sensitive to casting variables. Enlarging the gating system and adding additional gates to the ASTM mould can improve properties in the tilt position. The reproducibility of properties in as-cast and T6 heat treated bars was investigated.

Jan 1, 2004

By C. I. Garcia, G. Zhou, W. Gao, A. J. DeArdo

The development of X-100 and X-120 linepipe steels was investigated using a series of low-carbon Mo-Nb-B steels. The laboratory steels were vacuum melted and processed using advanced thermomechanical processing (TMP) philosophies. Prior to the laboratory hot-rolling experiments, the grain coarsening temperature, the conventional T95 and T5 start-stop recrystallization temperatures and the transformation behavior of y were studied using a computer-controlled high temperature deformation MTS-458 and a Theta-IV High Speed dilatometer systems. The results from these experiments provided the guidelines for the design of the laboratory hot-rolling TMP processing experiments. The mechanical properties of the experimental steels showed yield strengths in the range 700-850 MPa and CVN impact properties of over 80 J at -20°C. The best balance of mechanical properties was obtained by using CCR+DQ+Tempering treatments. The major microstructural features responsible for the observed mechanical properties in order of importance were: a) substructural refinement associated with lower bainite, b) dislocation strengthening, c) fine recrystallized ferrite, and d) small amounts of retained austenite. Fine Nb(C,N) precipitates formed in ferrite were observed, however their contribution to the strength was minimum. Most of the Nb(C,N) precipitation took place in austenite. This precipitation was used to exert microstructural control of austenite during hot rolling. The physical metallurgy and optimum TMP to achieve the mechanical properties are detailed in this paper.

Jan 1, 2005

By J. A. Morgan, W. A. Barclay, J. C. Pedersen, I. C. Campbell, D. S. Bubar, R. P. Taylor

"Abstract - The Lilypad Lakes property is host to a group of Ta-mineralized dikes that occur over an area of at least 10 km2. Field relationships are consistent with a syn- to late syn-tectonic timing for their emplacement (with respect to the major regional D1 episode of deformation), with several of the dikes exhibiting a steeply dipping, open, S- to M- to Z-shaped fold geometry. Individual dikes range up to 30 m wide (Rubellite Dyke, Pollucite Dyke), have strike lengths of up to 750 m (e.g., JJ Dyke), and are continuous to depths of greater than 250 m (e.g., Rubellite Dyke, Pollucite Dyke). Typically, they display sharp intrusive contacts characterized by the development of thin, holmquistite-rich haloes. The Tamineralized dikes are comprised of silica- and alumina-rich, sodic, granitic pegmatites that display extreme levels of geochemical fractionation (K/Rb typically < 10.0, as low as 2.2; Nb/Ta typically < 0.20, as low as 0.03), and enrichments in an economically important group of lithophile elements, most notably Li, Rb, Cs, and Ta. Geochemical assays of individual surface grab and drill core samples have yielded values as high as 1.51 wt.% Li2O, 1.25 wt.% Rb2O, 6.21 wt.% Cs2O, and 0.108 wt.% Ta2O5. Diamond drilling has established the presence of wide (~20 m), potentially ore-grade intersections of Ta mineralization (>0.045 wt.% Ta2O5) in both the Rubellite and the Pollucite Dykes.Three Ta-oxide minerals (microlite, wodginite, manganotantalite) of primary origin predominate in the Ta-mineralized dikes, where they occur as fine, disseminated grains in the albite-rich pegmatite matrix. The sequence of crystallization is typically manganotantalite wodginite microlite, which conforms to a well-established paragenetic sequence for rare-element granitic pegmatites in general. All three of the primary Ta oxides are characterized by a high degree of chemical purity (e.g., average Ta concentrations in microlite from 77-79 wt.% Ta2O5), a compositional feature consistent with the extreme levels of geochemical fractionation characteristic of the host granitic pegmatites, and one that indicates that the Lilypad Lakes pegmatites are likely to produce Ta mineral concentrates of the very highest quality.Locally, a second generation of Ta minerals is present, restricted to small vugs in the pegmatite matrix that are surrounded by fine aggregates of K-rich mica or clay. The secondary Ta minerals are dominated by microlite, which is typically intergrown with fluorite and Fe-sulphides, and is distinguished from its primary counterpart by its lower Ta content (around 70 wt.% Ta2O5) and much higher concentration of uranium (up to 9 wt.% UO2). Also, secondary microlite consistently yields low analytical totals from electron microprobe analysis, suggesting that it is H2O-rich. The presence of this second, vug-related generation of microlite, together with the occurrence of localized networks of crosscutting fractures that host high concentrations of Cs and Rb (in the minerals pollucite and Rb-Kfeldspar), suggests that a late-stage, fluid-dominated metasomatic/hydrothermal event may have been important in certain sections of the dikes, and has effected a redistribution of the economically important elements Ta and Cs."

Jan 1, 2005

By Michel Rodrigue, Sylvain Duchesne, Louis Racine

"LocationThe Louvicourt mine is located 20 km east of Val d'Or in Abitibi, in the northwest part of the province of Quebec. The mine is located on Highway 117 connecting Val d'Or to Montreal and very close to the main railway networkHistoryFive successive exploration attempts by Aur Resources resulted in the discovery of the large Louvicourt orebody in June 1989. Construction of the surface and underground infrastructures commenced in the spring of 1991. Milling operations commenced in July 1994. The entire project cost CDN$290 million, almost CDN$20 million less than initially estimated. The concentrator infrastructure cost CDN$64 million.Louvicourt mine is owned in partnership by Novicourt Inc. (45%), Teck Corporation (25%), and Aur Resources Inc., the administrator (30%).Brief DescriptionLouvicourt mine is the largest producer of base metals (Cu and Zn) in Abitibi-Temiscamingue. Its average daily production is nearly 4300 t of ore, for an annual production of 200 000 t of copper concentrate (28% Cu) and 33 000 t of zinc concentrate (57% Zn). After only a few weeks of operation, it had attained its objectives for the most part, and operations continue to be improved."

Jan 1, 2000

By G. Morin, F. Chiesa, B. Duchesne

The Quality index is a useful tool allowing to assess the metallurgical quality of aluminium AlSiMg foundry alloys (A356/357). Its value is calculated from the ultimate tensile strength and elongation; it increases with the metallurgical quality of the casting, i.e. with finer dendrites, lower microporosity and inclusion count and lower iron content. This Quality index does not depend on the degree of temper applied during the heat treatment (aging time and temperature). After defining the Quality index, it will be explained how it can be predicted from the knowledge of the local solidification conditions obtained from modelling. The paper will then present four case studies of castings for which the prediction of the Quality index by modelling was made. These case studies from different authors will involve the three most common casting processes used for producing high integrity aluminium castings, namely: sand casting, permanent mould casting and investment casting (lost wax). In all cases, the accuracy of the prediction will be assessed by comparing the predicted Quality index distributions to the experimental values based on the published measured values of the local tensile properties.

Jan 1, 2006

By H. C. L. Reemeyer

"The mining industry faces increasing economic, environmental and social challenges, as easier deposits deplete and ores become more difficult to mine and process; head grades decline; projects migrate to increasingly remote and difficult geographies; and the industry faces more stringent environmental and social standards. While these factors increase costs and risks, they also present opportunities for a more integrated approach to mining, processing, materials handling and waste management. Two key areas of risk are in tailings and water management. As mining and processing tonnage rates continue to increase, the disturbance footprints, water and energy consumption and scale of tailings storage facilities also rise. These factors can be mitigated by more selective mining, ore sorting and pre-concentration, and more intensive tailings dewatering. Such alternatives must be considered in conjunction with the selection of mining method, metallurgical flowsheets, major equipment selection, and key process design criteria. For example, increasing the grind size of a concentrator reduces energy consumption and eases tailings dewatering, but may cause challenges with metal recovery. Emerging technologies will be reviewed, and economic and environmental trade-offs for eco-efficient alternatives will be presented for metal sulfide mines.INTRODUCTION The metals mining industry faces significant challenges that can affect its financial viability and social license to operate. There has been a consistent decline in ore grades and a relentless push towards larger operations to capture perceived economies of scale. With these larger operations, the environmental footprint of mines has increased. Water and energy consumption, and resulting GHG emissions have also risen. In recent years, two issues have raised special concerns for stakeholders and companies: • Water scarcity, particularly in drier regions of the world such as Northern Chile, SW USA, Southern Africa and Australia • Tailings risks, following the high-profile failures of the Fundao tailings dam in Minas Gerais, Brazil in 2015 and the Mount Polley tailings dam in BC, Canada in 2014"

Jan 1, 2017

"IntroductionThe Chairman, in his speech to this body last year in Montreal, stated that the Dominion Coal Board looked to and depended upon the Bureau of Statistics for statistical material, and the Bureau does collect and publish monthly and annual data on coal. It may therefore be asked why an officer of the Dominion Coal Board should prepare and give a talk on statistics.I would explain that it has been our experience in the Board that, since the supply and consumption of coal in Canada is subject to a seasonal ebb and flow, it can be more profitably studied on the basis of a twelve-month period ending on March 31st than of a calendar year, since the end of March does represent a fairly stable end point in this ebb and flow. The figures are not prepared or published by the Bureau on that basis and it has therefore been thought that a presentation on this fiscal-year period would be of interest. The Bureau of Statistics has agreed that this may be valuable and all the data here presented are based on the reports secured from various sources by the Mining, Metallurgical and Chemical Division, Dominion Bureau of Statistics. The only contribution by either myself or the staff of the Dominion Coal Board has been the tabulation in a different twelve month period, and the comments upon the picture presented.It should be noted that the data for the month of March, 1950, are not available in all cases and consequently the figures for that year contain an estimate for this month."

Jan 1, 1950

By R. Lapcevic, P. Lokin

"Among other components, ore body „T“ was discovered in the Bor pit copper mine at a depth of app. 500m. The ore body is relatively small: 60-65m long, 40-45m wide and up to 50m high, but with an extremely high content of copper and accompanying metals. The rock mass containing the ore body is composed of altered andesite of relatively poor physical-mechanical characteristics. The exploitation of this ore body by way of conventional mining methods was associated with high risk, cost, and potential losses of the rich ore. Due to everything specified hereinbefore, the adopted solution involved ore exploitation with complete ensuring of excavation stability, thus forming an extremely large underground opening. The excavation and supporting were performed according to the NATM principles along with applying shotcrete, 9-25 m long cables, and horizontal and vertical lattice girders. The excavation of the ore body was completed in app. 2.5 years, all the while ensuring complete stability and security of people and equipment; construction works were constantly monitored. The proposed solution for ore excavation enabled more than 95% exploitation of ore as requested by the Investor, while depletion due to waste-rock excavation was less than the allowed 5%. INTRODUCTIONThe Bor copper deposit is located in Eastern Serbia. Copper exploitation in Bor commenced as far back as 1902. A total of 26 ore bodies varying in size and valuable mineral content have been excavated so far. One of the most recent excavated ore bodies is ore body „T“, which is one of the smallest bodies by volume, but also a body with one of the largest content of copper and accompanying metals. An important fact regarding its exploitation is that it is located at a depth of app. 500 m; that its shape is irregular: 60-65 m long; 40-45 m wide and app. 50 m high; and that it lays within a rock mass of relatively poor physical-mechanical characteristics. In addition, above it, in its immediate vicinity, ore body „F“ was previously excavated and its room was refilled with backfill and water. Excavation methods common in mining practice (excavation with caving, excavation with backfilling, excavation with protective pillars) were inadequate in this case for various reasons:• The immediate vicinity of the previous ore body „F“ room could cause expansion of the caving zone also to that room, along with penetration of groundwater and flotation sludge;• Possibility of deformation expansion caused by caving as far up as the surface of the terrain, including the urban area;• Difficulties in maintaining the stability of excavation sidewalls having steep slopes and great height;• Significant loss of ore mass with a relatively high content of metals etc."

Jan 1, 2015

By William M. Luff

This paper outlines the regional geology and history of the area, and summarizes the stratigraphy, structure and geology of the Brunswick No. 12 mine area. The Brunswick No. 12 deposit is a stratiform massive sulphide body. It occurs in rocks of the Tetagouche Group, which is believed to range in age from Lower to Middle Ordovician. The stratigraphic sequence, including the stratiform orebody, in ascending order consists of older metasedimentary rocks, augen schist, metasediments, augen. schist, footwall metasediments, the -massive sulphide body, iron formation, hanging-wall metasediments, siliceous tuff, basic volcanic rocks , basic iron formation and a porphyry dyke. This sequence is similar to that at some other deposits in the area. Four phases of structural deformation are known to be present in the Brunswick No. 12 mine area. The first deformation folds (F1 ) and associated faulting are the most important factors in determining the distribution of the massive sulphides. This deformation has resulted in the massive sulphides being separated into four zones: the Main Zone, the West Zone, the East Zone and the V-2 Zone. Brunswick Mining and Smelting Corporation Limited is actively mining, developing and exploring the deposit.

Jan 1, 1977

By G. F. Carr

"IntroductionFLUORSPAR has been found at several •localities in Newfoundland, but all the commercial deposits discovered to date are in the vicinity of St. Lawrence, a town on the southeast coast. Most of the veins are within six miles of St. Lawrence harbour, and between sea-level and an altitude of 400 feet. The St. Lawrence Corporation of Newfoundland, Limited, and Newfoundland Fluorspar, Limited, a subsidiary of the Aluminum Company of Canada. Limited. are the two producers.With the arrival of 1953, the St. Lawrence area entered upon its twenty-second •consecutive year as a producer of fluorspar. Production has increased more or less steadily during this period, as is shown by the fact that approximately one-half of the total shipments to date have been made during the past six years. Between four and five hundred men are employed by the industry, and more than $1,250,000 was paid out in wages and salaries during 1952. Shipments during that year reached an all-time high of 81,283 tons valued at $2,484,943, compared with 67,925 tons valued at $1,966,477 in 1951 (1).As a result of an agreement made in July, 1952, with the United States Defence Materials Procurement Agency, production of the St. Lawrence Corporation, Limited, and St. Lawrence Fluorspar, Incorporated, an affiliated company, will •be increased by .approximately 50,000 tons of acid-grade fluorspar per year. The contract extends over a period of four years, or until 150,000 tons of acid-grade concentrates have been produced."

Jan 1, 1954

By L. E. Djingheuzian

"IntroductionDURING the past two decades an enormous amount of empirical data has been accumulating on grinding. These data have been obtained by mill operators on grinding ores with a diversity of characteristics, and generally they have been published. However, whenever an operator, who has started milling on a new ore, has tried to find a case in literature which would exactly fit his particular grinding problem, he has failed. Evidently, something fundamental has been lacking in all these empirical data, and, as a consequence, each new operator has had to undertake his own experimenting, get the best results he can, maybe publish these results, and let it go at that. This, in the writer's opinion, has been• due to the fact that even the ablest and most inquisitive millman has been forced to look on grinding as an art, and so, except very rarely, has not been able to find the time to stop and think; if he did so, it was rather in a philosophic way, that grinding is a fundamental process, a process that takes place in river beds, on the sea shore, etc.Nevertheless, when all the data so far published are correlated and examined as a whole, one is struck with the advances that have been made in grinding. The writer (7) had made such a study in 1949, and, when the correlation was completed, it showed that there was nothing heterogeneous about the accumulated data and that when brought together they were in harmony with each other. The writer's conclusion was that, if grinding criteria were defined and were expressed in such a way as to make integration of any data into basic formulae possible, grinding would be established as a mathematically exact science, and grinding worries of the harassed mill operator would be at an end!The first attempts to rationalize comminution were made by Rittinger and Kick. However, their theories led to endless disputes which did not accomplish much, except possibly clearing the path for subsequent investigators."

Jan 1, 1952

By Charles B. Newmarch

Abstract In the course of coal studies undertaken by the B.C. Department of Mines in southeastern British Columbia, special attention was directed to problems of coal seam correlation. Methods that had been used successfully in other coalfields were found, in the Crowsnest area, to have a restricted use or furnished only additional evidence that might prove helpful when used in conjunction with other criteria. A correlation technique involving semi-quantitative spectrographic analyses of coal ashes was developed. Elements detected in the ash include Si, B, P, Fe, Mg, Mn, Pb, Ti, Cr, Ga, Ca, Al, Ge, Ba, Mo, V, Ag, ?y;b, Na, Zn, Zr, Ni, Sr, Cu, K. Of these, the elements found to be most useful in correlation were Na, Ba, Si, V, and Mg. The element Na was invariably detected in the ash from one of the seams but was not found in samples taken from any of the others. In all of the four seams sampled statistically, significant differences in the amount of certain trace elements were noted. When the values obtained for these trace elements were portrayed in the form of histograms, the resulting diagrams had a characteristic shape for each seam. The diagrams provided a basis for seam identification within the limited area (8,000 feet by 4,000 feet) that was investigated. Introduction During the field seasons of 1946, 1947, and 1948 the British Columbia Department of Mines undertook a geological investigation of the coal measures of southeastern B.C. As field work progressed in the Crowsnest area it was found that, within the Kootenay formation, which contains all the commercial seams of the region, the coal beds are the most persistent stratigraphic units. Because of relatively rapid changes in ?both the thickness of the seams and the interval between seams, difficulty has invariably been experienced in attempts at correlation. Even short-range correlati0ns by able geologists who have worked in the Crowsnest coal basin have been questioned by the operating companies. It was apparent, therefore, that a more dependable correlation technique was needed so that stratigraphic and structural studies could be of greatest value. This paper presents, firstly, a summary of the results obtained in attempted correlations using methods that have been found effective in other coalfields. Secondly, a method based on semi-quantitative spectrographic analysis of coal ash is described and the apparently promising results are discussed.

Jan 1, 1950

By G. E. Wittur

"The twenty-one members of the Organization for Economic Cooperation and Development, comprising eighteen western European nations plus Canada, the United States and Japan. account for two-thirds of world steel production. The Special Committee for Iron and Steel was formed by the OECD to study trends and problems in the steel industries of member countries. The paper begins with a summary on the Organization, including an historical sketch, its structure, member-ship and objectives. The steel industry of the entire OECD is briefly described before proceeding to a more detailed discussion of various aspects of the steel industries of European OECD members, emphasizing practices and conditions that differ from those in North America. Benefits to Canada of representation at meetings of the OECD Special Committee for Iron and Steel are described."

Jan 1, 1967