Search Documents

By T. Imgrund, A. Bischoff, S. Spürk

"Specific conditions of underground coal mines at great depth, such as high temperatures, high rates of methane inflow and natural ventilation pressure provide considerable challenges for the reliable design of appropriate mine ventilation systems. For decades coal mining in Germany has coped with these extreme circumstances. Based on these experiences appropriate software tools for simulating mine ventilation networks have been developed and continuously enhanced. This paper examines differences in the simulation results and underlying calculation methods of two software solutions. The analysis is based on the comparison of FlowNetTM and VentSim DesignTM (Version 5.1) regarding the accurate prediction of fluid mechanical quantities and their validation with real measurements. A special focus lies on exceptional ventilation scenarios typical for deep coal mines, like gas inflows, fire events and buoyancy effects. The purpose of the comparison is the future utilization of the experiences gained during mining at up to 1,500 m depth for state of the art ventilation design. INTRODUCTION Ventilation is an essential component of mine operations—as providing fresh air to workplaces, diluting and removing explosive, toxic or asphyxiating pollutants and assuring sufficient climate conditions. On the other hand, the costs of ventilation contribute to a large extend to the overall operating costs of a mine, as the share in the energy consumption of a mine may be in the range of 25–50% (Belle, 2008). Accordingly, proper design of ventilation systems has been a task since early times. Consequently software for modelling of ventilation networks has been developed in order to improve efficiency and accuracy of calculations (Maleki, 2018). Compressible flow has not been considered by initial ventilation modelling software tools. In Germany, the consideration of changes in airflow density—depending on pressure and temperature—in the algorithms of ventilation simulation software has been started in 1974 by Duepre & Hofbauer. This development had been continued by the Pruefstelle fuer Grubenbewetterung (Test Centre for Mine Ventilation) and resulted in the release of a computer ventilation software named “Wetter”. The mine inspectorate of the German state of North Rhine-Westphalia, which supervises the major coal mining district in Germany, declared ventilation simulation based on compressible flow being “state of the art” in 1985 (Pollak, 1985). This pronouncement made allowance for assessing the consequences of underground fires and downtimes of main fans based on advanced software solutions."

Jan 1, 2019

By W. A. Lang

Introduction In this review, which is the fifth of the series on the Progress in Coal Technology, an attempt has been made to outline some of the more important developments that have taken place in coal carbonization during the last decade. Research into both high-and low-temperature carbonization has been active for three principal reasons: (1) the growing shortages in most countries of high-quality coking coals; (2) the demand for smokeless fuels for domestic purposes; (3) the need for metallurgical coke for the increased output of steel in the post-war years. The growing importance of coal tars as a source of chemicals for the preparation of synthetic products and of coal gases for the recovery of sulphur is evident. Many of the researches initiated because of wartime necessity have been continued .and even expanded in the post-war years. High-temperature carbonization with a suitable coal yields a strong coke which is used primarily for metallurgical purposes, a tar with good marketable value, and a large yield of gas of medium calorific value. Low-temperature carbonization gives a more free-burning solid product suitable for a domestic fuel, a high yield of a tar which is generally regarded as superior to high-temperature tar for chemical purposes, and a smaller yield of a higher-heat-value gas.

Jan 1, 1951

By Phil A. Keele

"IntroductionGeneralThe Genesee Coal Mine is a joint venture of Fording Coal Limited and the city of Edmonton. The mine supplies thermal coal to the Genesee Generating Station operated by Edmonton Power and is located approximately 75 km southwest of Edmonton (Fig. I).Under the terms of the joint venture agreement, Fording Coal Limited has designed and developed the Genesee Coal Mine. Fording also operates the mine which has a minimum economic life of thirty-five years. Mine development started in the spring of 1987 with the construction of the dragline erection pad and mine service complex. Major development of mining areas was carried out in 1988 with the construction of haul roads, powerlines, topsoil recovery, etc. Mining officially commenced on December 14,1988.The mine produces 1.6 million tonnes of coal per year and employs 65 people. MiningGround conditions have turned out to be very poor, as expected with the majority of the overburden in the first few years a soft lacustrine clay with minor amounts of fine-grained glacial till. To compound matters, what was expected to be a relatively uniform coal subcrop turned out to be a very irregular erosional contact.The coal mined at Genesee is a sub-bituminous Class B thermal coal with approximately 16070 ash, 21% moisture, 8300 Btu/lb and 0.27% sulphur on an as-mined basis.The primary piece of mining equipment used at the Genesee Coal Mine is a M8200 walking dragline. It has an effective operating radius of 100.6 m, a 50.5 m3 bucket, and weighs approximately 3860 tonnes yielding a ground pressure of III KN/m2•Figure 2 illustrates schematically the single pass mining sequence presently employed at the Genesee Coal Mine. The M8200 is used to lift all coal out of the cut, the coal being placed in stockpiles on the prepared pad .This method maximizes coal recovery under the conditions where spoil failures due to poor material would otherwise put men and equipment at risk. The coal is subsequently loaded by the coal shovel operating on the same bench as the M8200 dragline and delivered to the plant as required.All mined areas, as required under Alberta Legislation, are to be returned to an agricultural land capability equal to or better than that which existed prior to mining. Reclamation activities, as a result, are an important and integral part of the mining process. A complete list of the primary mining equipment deployed at the Genesee Operations appears in Table I."

Jan 1, 1994

By Rong. G., T. Q. Lin, W. Du

Based on analysis of the evolutionary history of the valley in Baihetan, the mechanism of asymmetrical evolution, gradual migration-incision evolved from left bank to the right, is revealed in Baihetan river valleys. The process of in-situ stress evolution is carried out by using the Universal Distinct Element Code (UDEC). Consequently, the numerical results which indicate the main regulations of that stress field are as follow: (1) The phenomenon termed "high in-situ stress fold" appears in the bottom of the valley. With the maximum principal stress being 28-34 MPa, the stress increases significantly at a vertical depth of approximately 130 m. (2) The in-situ stress presents zonal distribution along the bank slope. It is apparent that the in-situ stress field consists of stress relaxation zone (SRZ), stress concentration zone (SCZ) and original stress zone (OSZ). The horizontal depth of stress relaxation zone varies from the left bank (roughly 200 m) to the right (about 120 m). Furthermore, the stress evolution of the left bank slope is studied. As a result, it is found that asymmetrical erosion contributes to the difference of the in-situ stress distribution as a critical factor, between the left bank and the right. And for an asymmetrical valley, the evolutionary process of in-situ stress field is a circular procedure, which includes the incision of valley, the accumulation of landslides and the migration of valley.

Jan 1, 2015

By K. Musgrave

"The ISO 9000 Quality Management System Standards have become internationally accepted as the way to manage quality assurance. The author has developed a Maintenance Management System Standard using ISO 9001as a model and is working with a major basemetal mining company to implement this. This paper describes the structure of the standard and the steps required for its implementation.Using a management standard ensures that a system is maintained, reviewed by internal audit, and when instances of failing to follow the procedures (nonconformances) occur, that corrective action is taken. It also ensures that regular reviews are made and that the sys-tem is continuously improved.The Standard is designed so that if an organization decides to register to an ISO 9000standard, the Maintenance Management System will be in a format that is compatible and can be incorporated with little effort into the Quality System.IntroductionIn reviewing maintenance operations at many mining companies, and often seeing those same organizations some years later, two recurring issues have been noticed..The first issue is how dependent effective maintenance is upon individual supervisors and crews. In one situation, a mine that had an excellent maintenance system in the 1980s. Now, with new supervisors and crews, it is starting to develop a system that will bring it back to where it once was. No written procedures remain from the earlier excellent system.The second issue is that most operations feel that maintenance is the sole responsibility of the maintenance supervisors and crews. Nothing could be further from the truth. Maintenance, like safety, is everyone’s responsibility. If the operator does not report problems and perform daily checks, and if the production supervisor runs equipment until it fails, then nothing the maintenance crew does will prevent emergency breakdowns and lost production. More importantly, equipment will be operated in unsafe conditions, putting employees at risk and, with today’s regulations, leaving supervisors open to prosecution.The Maintenance Management System outlined in this paper is designed to establish the present best practices as standard procedures, to provide a continual review so that these practices are improved in the future, and to identify instances where the system fails so that corrective action is taken. The mine referred to above is using this approach to make sure that, this time, the system it implements will survive."

Jan 1, 1997

By A. F. Sirianni

The Peace River iron ore deposit represents the sole source of raw material for an integrated steel industry in Alberta. The ore has proved refractory to beneficiation by a number of techniques. A selective oil-phase agglomeration technique is described. Medium-grade concentrates, analyzing 48-53% Fe and 10-14% SiO2 were obtained with recoveries of about 75% of the total iron. These results appear to represent the optimum possible for this ore body.

Jan 1, 1977

By A. McLean, M. Barati

In this paper, examples are presented of pyrometallurgical research and associated teaching activities during the past century within the Department of Metallurgical Engineering, now the Department of Materials Science and Engineering, at the University of Toronto. Throughout these years, pyrometallurgical research has been characterized by recognition of the importance of the interdependence of measurements and models as well as the development and application of sensors, for the generation, validation and practical implementation of new knowledge. The important role played in the delivery of lectures and participation in joint research by Adjunct Professors with strong backgrounds in the pyrometallurgical industry is described. Projects conducted in close collaboration with the industrial sector and opportunities for students to obtain practical experience working as teams on a "round-the clock" shift basis within an industrial pilot plant environment are outlined. These activities, together with the involvement of students in poster competitions and the presentation of papers at society conferences and technical meetings, are still vital elements in the development of pyrometallurgists equipped with the appropriate professional skills for subsequent employment within academia, government laboratories or the industrial sector.

Jan 1, 2015

By L. E. Fischer

The background for the 630-million-dollar-plus iron ore project at Kudremukh is outlined. The system and plants for mining, crushing, concentrating, transporting via a slurry pipeline, filtering and shiploading 7.5 million metric tons of iron ore per year are fully described. The mode of operation and the problems encountered in such a transfer of North American technology to developing countries are analyzed. Difficulties encountered during construction are discussed and the progress milestones made over a two-year period are enumerated.

Jan 1, 1979

During the past decade, the miner-al industries have been faced with an increasing shortage of engineers. The point has now been reached where the shortage may be termed critical. This shortage may be attributed directly to declining enrollment in the mineral science programs offered by the universities on this continent. Although the reasons for declining enrollment are undoubtedly many, two major hypotheses may be postulated. The first is that high-school graduates are either unaware of the mineral industries and the opportunities in them or that they are aware of them but have somehow obtained a false image of their true nature. The second is that they are aware of the true nature of these industries and the opportunities they offer but find them exceedingly unattractive. The problem of dwindling enrollments has, in recent years, been subjected to a concerted attack by the industries and professions concerned. However, their efforts to date have been based essentially on the first hypothesis. Sufficient results are now available to suggest that either the methods of attack are inappropriate

Jan 1, 1965

By J. Suarez Condezo, E. Herrera Alarcon

The Ilo Smelter Modernization Project will require treating the slag from the Peirce Smith converters in Slag Cleaning Furnaces using pig iron technology. Currently the slags from the converters show variable magnetite contents. The copper contained in this slag is recovered in Reverberatory Furnaces, where the smelting rate was improved due to the high silica content of the converter slag. Preliminary industrial tests where developed to clean the slag from converters using pig iron. The results showed that the magnetite content has a significant influence in this process. This work describes the actions that are being implemented in the converter operation to control the magnetite content in the slag in order to maintain the high copper recovery of the smelter when the new facilities are commissioned. This task will demand a strong control of both the slag chemistry and converter practices in order to get the copper recovery considered as the design criteria (~97.4%).

Jan 1, 2007

By J. Jerome MacDonald, Stephen B. Flewelling

"In the base metals industry of today, operations required to continuously improve productivity and reduce unit production costs. Consistent with these goals is the improvement of the muck haulage cycle from open stopes with the No. 12 Mine.Existing haulage from open stopes occurs with LHD units experience at Brunswick indicates that LHD units have a higher unit cost per tonne mucked than loader-truck combinations when the haulage exceeds approximately 150 m.The reintroduction of open stoping at Brunswick made existing loader-truck combinations unsuitable. It was recognized that application of recent continuous loading technology could potentially result in significant unit cost savings and productivity increases.A review of the technology resulted in the testing of the Voest Alpine AL60 loader in the open stopes located on the 1000m Le vel. Testing began in January 1988 and finished in late November 1988. The test will provide experience as well as quantified production and maintenenace parameters f or the purpose of quantifying production unit costs and system productivity, ultimately resulting in a decision to further utilize or not utilize the loader as a primarymucking unit at Brunswick .INTRODUCTIONBrunswick Mining and Smelting Corporation Ltd. produces approximately 10500 tonnes per day from the No. 12Mine located 35 km southwest of Bathurst, New Brunswick Mining is the largest (single mine) producer of zinc in the world having mined over 52 million tonnes since 1964. Many years of production still remain with proven and probable reserves in excess of 90 million tonnes. Reserves grade at an average of 3.65% Pb. 8.99070 Zn, 99g/mt Ag and 0.32% Cu . The operation employs 1446 people with approximately 800underground including operations and maintenance staff.In the No. 12 Mine two major mining methods are presently utilized . The primary method is Mechanized Cut and Fill (MCF) accounting for approximately 6500 tonnes per day from four major areas. The remaining 4000 tonnes per day is produced from open stopes with the majority of 2800 tonnes per day being produced by the 1000 level.The 1000Level contains 30 million tonnes segmented into open stope blocks 30 m high, 15m and 30 m on strike , with a transverse width of 10m to 50 m (Fig. I). Stopes are organized on a primary secondary stope arrangement along strike. Primary stopes are undercut and overcut full size with the back fully cablebolted. All stope and lateral development is driven 4.0 m high. All stopes to date are flat bottom (Fig. 2). Primary stopes are filled with cemented rock- fill , secondaries with conventional rockfill, Haulage from the stopes is primarily with 8-yard LHD units ; mucking is approximately 50% conventional and 50% remote. Haul distance to date has averaged approximately 150m with current stope haul distances of approximately 300m. Haulage is presently to a small jaw crusher situated on the 1000 Level. From August 1989on, haulage will be to a set of ore passes feeding to a large gyratory crusher situated on the 1200 Level. Start up of the gyratory crusher corresponds to an increase in tonnage from 1000 Level to 4100 tonnes per day."

Jan 1, 1989

By Chantale Doucet

L?utilisation du remblai en pâte dans les exploitations en vrac est de plus en plus importante. Puisque la technologie existe pour fabriquer du remblai en pâte sans construire une usine coûteuse, il est maintenant possible d?élargir le domaine d?utilisation du remblai en pâte pour y inclure des gisements filoniens où le besoin annuel de remblai est moindre. Dans certains cas, l?utilisation du remblai en pâte pourrait permettre de réaliser d?importantes économies telles que la réduction de la dilution, la stabilité des ouvertures, la récupération d?une plus grande partie du minerai par la réduction de la taille des piliers et l?entreposage de moins de résidus à la surface. L?ampleur des économies est parfois difficile à chiffrer mais il est tout de même important d?en tenir compte lors de la décision d?utiliser du remblai en pâte puisque ce sont souvent ces économies qui seront déterminantes. Différentes méthodes d?extraction avec remblai en pâte appliquées aux mines filoniennes seront présentées. Des défis et les solutions reliés à l?utilisation du remblai en pâte à la Mine Doyon seront discutés.

Oct 1, 2001

By R. B. Fermor

"AbstractAttention is drawn to the ventilation problems arising from the use of diesel vehicles underground, especially in view of the fact that diesel fumes in combination with other pollutants may be more harmful than diesel fumes alone or the other pollutants alone.Means for minimizing the harmful effects of using diesels underground are listed, and the quantities of air' required in mines in which diesel-powered vehicles are used are discussed. Mines are classified in three categories on the basis of severity of ventilation problems, and statistics are given for these categories.Details of the various components contributing to total ventilation needs are given, and the ventilation needs of individual mines in the three categories are listed. A description is given of the principles according to which main ventilation coursing is planned and the selection and siting of main fans is discussed.General Considerations in the Use of Diesel-Engined Vehicles UndergroundIN ORDER to reduce physiological hazards, present and latent, to workers in mines in which extensive use is made of diesel equipment underground, it is important that mine ventilation systems reduce the concentrations of rock dust, diesel fumes and particulate matter as rapidly as possible to an acceptable level in all parts of the mine.There is some evidence that the long-term effects of a combination of the above pollutants are greater than those of anyone of them alone, which makes the problem even more pressing."

Jan 1, 1977

By W. Mueller, M. Rocheleau, E. Dimroth

The paleogeographic evolution of the Abitibi Belt is subdivided into three phases, namely: 1) a phase of the growth of a submarine volcanic chain, 2) a phase of the emergence and growth of volcanic islands and 3) a phase of uplif t and erosion of volcanic islands. Isostatic calculations suggest that the volcanic sequence in the south of the Abitibi Belt rests on oceanic basement or on the mantle; the volcanic sequence in the north of the belt rests on about 13-14 km of tonalitic basement. 10-15 km of plutonic material accreted to the volcanic islands during paleogeographic phases 1 and 2, and caused the uplif t during paleogeographic phase 3.

Jan 1, 1984

By James McManus

The original analogue instrumentation at Lornex Mining Corporation to optimize the throughput by controlling the power drawn by the semi-autogenous mills was found to be inadequate because of the frequent changes in ore type. Although the trunnion bearing pressure of the mill was a crucial control criterion, it was not utilized in the original control scheme. After several plant tests of different types of analogue controllers were unsuccessful in finding any control equipment suitable for this application, it was concluded that a digital process control computer was required. Computer control strategy to optimize the grinding rate by controlling the power and the bearing pressure of the semi-autogenous mill was developed and a Fox 2 /30 computer made by Foxboro was selected. After six months of experimentation, it was found that the throughput was increased substantially by computer control.

Jan 1, 1978

By J. C. Marchand, M. A. Berube

"L'objectif principal recherché lors du broyage d 'un minerai est de libérer adéquatement ses valeurs utiles en vue de leur concentration ultérieure. La pratique courante consiste à tenter d'obtenir un produit de broyage d'une granulométrie constante. Malheureusement, les propriétés texturales des minéraux utiles varient naturellement dans un gisement et une telle stratégie n'entraine pas toujours pour ces minéraux un degré de libération constant. Pour un rendement optimal du procédé de concentration, cette variable très importante doit donc être périodiquement vérifiée.Jusqu'à maintenant, la plupart des études de libération des minerais se font en examinant des sections polies de particules du minerai broyé. Le GRAAIM a récemment assemblé un système modulaire d'analyse d'images qui servira en grande partie à des mesures automatiques du degré de libération des minéraux. Le système s'avère relativement peu coûteux comparativement à la plupart des analyseurs de texture conventionnels si l'on considère que plusieurs de ses composantes, par exemple le miniordinateur, sont utilisées à une foule d'autres applications, et il permet de plus une grande souplesse d'utilisation puisque l'on a qu'à construire des algorithmes de mesure et de calcul en fonction de l'objectif recherché. Des programmes particuliers permettant des études automatiques de libération sur des sections polies de particules ont ainsi été élaborés. Ils permettent également des mesures de teneurs et de distributions granulométriques apparentes des particules. Des résultats obtenus dans le cas de minerais de fer sont brièvement présentés afin d'illustrer la technique."

Jan 1, 1983

By S. Foged

Umicore and MWH jointly demonstrated that mechanical dewatering of goethite and neutralised tailings significantly increased the life of a 30 ha tailings pond and improved the operation of the pond. Umicore operates one of its zinc production plants in Balen, Belgium. As part of its production process, an excess of neutralised and goethite¬containing tailings is generated. These have historically been stored inside large lined ponds. As the storage area of the current goethite pond was nearing its capacity, Umicore studied the potential for an extension to the existing embankment. However, this extension would face intense regulatory scrutiny, because the environmental and safety impacts were considered important. Together with Umicore, MWH suggested and investigated an alternative treatment approach consisting of mechanical dewatering prior to storage. A feasibility study was prepared where wet storage was compared to dry storage. Differences in safety risks, environmental impacts and economic costs were outlined. The study demonstrated that the life of the tailings pond could be increased from 6 to 22 years, seriously reducing the environmental impacts and safety risks at no significantly higher cost than would have been incurred with the continued operation of the existing pond. The results of the study are presented in this paper.

Jan 1, 2006

By R. Fukuzawa

"The objective of this research is to evaluate the magnitude of carbon prices required to drive process development and innovation for the global nickel industry in a direction that tackles the multifaceted sustainability challenges that the industry faces, including air pollution reduction and greenhouse gas abatement. The results suggest that the currently considered carbon prices are not sufficient to drive innovations in processing methods or upstream pollution prevention. The co-benefits of climate change mitigation and pollution prevention cannot be readily realized under climate change policy alone. Increased coordination between climate change policy and performance-based environmental legislation is necessary. INTRODUCTIONNickel is an important metal in our modern society as it is used in stainless steel, alloys, electroplating and rechargeable batteries, all of which are integral to our economic growth and development (Eckelman, 2010).However, nickel production is energy intensive and therefore susceptible to emerging climate change policies, which may lead to production curtailment and/or increased unit costs of production unless changes in efficiency or energy sources are made (Mudd, 2010). The industry is faced with multi-faceted constraints: future technology must not only deal with metallurgical, financial and environmental constraints but also promote low energy and low carbon practices. This presents a challenge for this industry where technology innovation, development and commercialization are often lengthy, risky and costly processes (Imrie, 2006).Climate change is one of the many challenges faced by our society. Others include other pollution to air, water and land, resources shortage and economic development. From a policy perspective, it is important to balance multiple and often competing needs in an integrated manner. It would require some levels of trade-off in order to maximize the overall effectiveness but also to ensure that one policy does not undermine other policy objectives.The aims of this study are to evaluate how developments in climate change policy would affect the nickel industry in the context of existing environmental regulations and how the industry could respond under these constraints."

Jan 1, 2012

By Ahmad Ghahreman, James McNeice

"Cerium is the most abundant rare earth metal and is often found in deposits along with small amounts of more valuable metals such as neodymium and gadolinium1. As a result, the production of cerium oxide often exceeds market demands, thus in some cases it would make more sense to remove the cerium from the process solutions before further purification. A common method of cerium removal is to precipitate CeO2 from the acidic leach liquors by raising the pH to oxidize cerium(III) to cerium(IV). This study investigates the oxidation kinetics using three oxidants; hydrogen peroxide, sodium hypochlorite, and potassium permanganate. The effect of oxidant, pH, cerium concentration and temperature on the oxidation kinetics will be discussed. Cerium oxidation in solutions with pH ranging from 1.0 to 4.0 was investigated at cerium concentrations ranging from 2.0 g/L to 16.0 g/L. A cerium recovery of 40% can be achieved at different conditions with each oxidant at room temperature, with higher recovery at 60°C.INTRODUCTION Over the last 70 years, the rare earth elements (REE) have become crucial components of modern technology. These metals are categorized as light rare earths (LREE) or heavy rare earths (HREE) by governments and miners based on weight, abundance, and therefore value. The minerals bastnaesite, monazite, and xenotime compose the majority of the world?s exploitable sources of these metals (Binnemans, 2013; Parker and Baroch, 1971). Geologists classify the LREE ores as „cerium group? minerals, approximately 50% cerium oxide by weight. The cerium group minerals monazite and bastnaesite compose the majority of world production, leading to an overproduction of cerium relative to world demand. This ratio of light to heavy REE in deposits has led to a phenomenon referred to as the balance problem (Binnemans et al., 2013). As an example, to produce 1 tonne of europium oxide from a bastnaesite deposit 450 tonnes of cerium oxide must be processed. This means that any push to increase production and access the value of the HREE metals will drive down the value of the LREE metals leading to diminishing returns (Zepf, 2016). These ores also contain measurable levels of thorium, subjecting them to complex radioactive waste regulations. During the 20th century, the USA was the largest producer of rare earth metals (REMs), primarily sourced from the Mountain Pass mine in California. However, due to a combination of market dynamics and regulations, China has dominated the market for the last two decades. The largest Chinese REE mine, Bayan Obo, produces rare earth (RE) concentrate as a byproduct of iron mining, decreasing their relative production costs (Gupta and Krishnamurthy, 2005). This mine alone represents about half of world bastnaesite production (Zhi and Yang, 2014). Rising demand for high-tech products has forced Chinese producers to commission other large mines, climbing to 90% of world production in the early years of the new millennium (Mancheri, 2016). This presents the west with a looming supply risk of these critical metals in the future."

Jan 1, 2017

By Guy Archambault, Réal Daigneault

"Un trait marquant du cadre tectorwstratigraphique de la Sous-province de l'Abitibi est la présence de nombreux couloirs de déformation d’extension régionale et sub-concordants au grain stratigraphique. La présence de grandes masses granitoïdes qui perturbent l'allure du grain tectonique est typique de la partie nord de la Sous-province de l'Abitibi. Des rides E-W constituées de complexes plutoniques précoces forment des reliefs structuraux agissant comme des moles résistants qui interfèrent avec la déformation régionale.Deux types de couloirs de déformation sont distingués, les couloirs de bordure et les discontinuités structurales. Les couloirs de bordure représentent des auréoles de déformation élevée qui s’accompagnent généralement d’un métamorphisme au faciès amphibolite. lls suivent /'interface entre les roches granitoïdes et les assemblages supracrustaux. Ces couloirs sont de puissance kilométrique et sont confines, surtout au sein des roches vertes, a l’interface des complexes granitoïdes d’importance. La limite entre la Sous-province de l'Opatica et les roches supra crustales de l'Abitibi est caractérisée par un important couloir de bordure issu possiblement d'un chargement tectonique irrégulier et concentre lors du raccourcissement horizontal.Les discontinuités structurales sont des failles ductiles qui se propagent surtout en direction E-W mais avec des variantes de directions SE et NE. Les discontinuités E-W se caractérisent par la présence d'une linéation d'étirement à fort angle de chute. Les discontinuités SE sont caractérisées par des linéations d'étirement horizontales et directionnelles et les mouvements observes sont system attiquement dextres. Les discontinuités NE sont des failles à comportement beaucoup plus fragile et se distinguent par des composantes de mouvement senestre. Elles sont tar dives par rapport aux discontinuités E-W et SE et ne représentent pas la symétrique du système SE.La combinaison des systèmes E-W et SE décrit un motif anastomose a l' échelle régionale. Les failles ductiles se rejoignent defaçon asymptotique, isolant des blocs peu ou pas affectes par la déformation. L'anastomose est un phénomène qui se produit a toute échelle et est reliée principalement aux Mt érogénéités et aux anisotropies 1) des forces agissantes (champs de contraintes régionale et locale) et 2) de la réponse del' empilement supra crustal (compositions différentes, fabrique initiate, propriétés mécaniques variées, niveaux d'altération).Dans le but de respecter un raccourcissement horizontal N-S, différents modelés sont proposés; ils mettent en cause soit une transpression dextre, soit des failles inverses réactivées en failles décrochèrent dextres soit des failles de chevauchement redressées."

Jan 1, 1990